plaintext email - Page 420

Poor upload/download speed on 2 x ADSL lines into a Cisco 2621XM

- by 2020mobile

Hi, Sorry never been on this site before so I apologise if not the right section or even forum. I have users complaining of very slow internetn connectivity on site and have checked with our ISP who have said that the line is testing at 8mb. We have 2 x BT lines that have our ISP broadand on them. Both lines go into a Cisco 2600 series router that then has a PIX firewall off that. Connectivity is successful just gone really slow and unable to download anything. Config is below: version 12.3 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ROUTER-ADSL-INTERNET ! logging buffered 16384 informational enable secret xxx enable password xxx ! username xxx username xxx clock summer-time UK recurring last Sun Mar 1:00 last Sun Oct 1:00 aaa new-model ! ! aaa authentication login default local aaa authorization exec default local aaa session-id common ip subnet-zero no ip source-route ! ! ! ip audit notify log ip audit po max-events 100 no ip bootp server ip name-server 213.208.106.212 no mpls ldp logging neighbor-changes no ftp-server write-enable ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! ! ! ! ! ! ! interface ATM0/0 description 01270 111111 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/0 ip address 82.133.32.9 255.255.255.248 shutdown speed 100 full-duplex no cdp enable ! interface ATM0/1 description 01270 222222 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/1 ip address 217.146.115.49 255.255.255.240 duplex auto speed auto no cdp enable ! interface Dialer0 ip address 217.146.115.250 255.255.255.248 encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication chap callin ppp chap hostname [email protected] ppp chap password 7 xxxxx ppp multilink ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! no logging trap access-list 10 permit 217.146.115.50 access-list 10 permit 82.133.32.10 access-list 10 deny any access-list 22 permit 217.146.115.50 access-list 22 permit 217.206.239.86 access-list 22 permit 82.133.32.10 access-list 22 deny any dialer-list 1 protocol ip permit no cdp run ! ! snmp-server community xxxxxx RO 10 snmp-server enable traps tty radius-server authorization permit missing Service-Type ! ! ! ! ! ! line con 0 exec-timeout 5 0 password 7 xxxxxx line aux 0 no exec line vty 0 4 access-class 22 in exec-timeout 5 0 password 7 xxxxxx transport input telnet ssh transport output none line vty 5 15 password 7 xxxxxx transport input telnet ssh ! ntp clock-period 17180095 ntp server 130.88.200.98 ! ! end Now my knowledge is very limited but ISP have said that while the lines are bonded each needs a seperate login as they've recently changed their L2TP router and that enforces the use of seperate logins - when the lines were configured we were given two logins. So, my question is what changes do I need to make to the config in order to get this working? it was ok before their change and I do have another login :- 01270 111111 - [email protected] 01270 222222 - [email protected] Apologies for the long email and thanks for taking the time to read it. Any more info I can provide please let me know. Thanks,

Read the article

Postfix "warning: cannot get RSA private key from file"

- by phew

I just followed this tutorial to set up a postfix mailserver with dovecot and mysql as backend for virtual users. Now I got the most parts working, I can connect to pop3 pop3s imap and imaps. Using echo TEST-MAIL | mail [email protected] works fine, when I log into my hotmail account it shows the email. It also works in reverse hence my MX entry for mydomain.com finally has been propagated, so I am being able to receive emails sent from [email protected] to [email protected] and view them in Thunderbird using STARTTLS via IMAP. Doing a bit more research after I got the error message "5.7.1 : Relay access denied" when trying to send mails to [email protected] using Thunderbird being logged into [email protected], I figured out that my server was acting as an "Open Mail Relay", which - ofcourse - is a bad thing. Digging more into the optional parts of the tutorial like shown workaround.org/comment/2536 and workaround.org/ispmail/squeeze/postfix-smtp-auth I decided to complete these steps aswell to be able to send mails via [email protected] through Mozilla Thunderbird, not getting the error message "5.7.1 : Relay access denied" anymore (as common mailservers reject open relayed emails). But now I ran into an error trying to get postfix working with SMTPS, in /var/log/mail.log it reads Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: cannot get RSA private key from file /etc/ssl/certs/postfix.pem: disabling TLS support Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: TLS library problem: 20251:error:0906D06C:PEM routines:PEM_read_bio:no start line:pem_lib.c:650:Expecting: ANY PRIVATE KEY: Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: TLS library problem: 20251:error:140B0009:SSL routines:SSL_CTX_use_PrivateKey_file:PEM lib:ssl_rsa.c:669: That error is logged right after I try to send a mail from my newly installed mailserver using SMTP SSL/TLS via port 465 in Thunderbird. Thunderbird then tells me a timeout occured. Google has a few results concerning that problem, yet I couldn't get it working with any of those. I would link some of them here but as a new user I am only allowed to use two hyperlinks. My /etc/postfix/master.cf looks like smtp inet n - - - - smtpd smtps inet n - - - - smtpd -o smtpd_tls_wrappermode=yes -o smtpd_sasl_auth_enable=yes and nmap tells me PORT STATE SERVICE [...] 465/tcp open smtps [...] my /etc/postfix/main.cf looks like smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no append_dot_mydomain = no readme_directory = no #smtpd_tls_cert_file = /etc/ssl/certs/postfix.pem #default postfix generated #smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key #default postfix generated smtpd_tls_cert_file = /etc/ssl/certs/postfix.pem smptd_tls_key_file = /etc/ssl/private/postfix.pem smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smptd_sasl_auth_enable = yes smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination myhostname = mydomain.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost.com, localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all virtual_mailbox_domains = mysql:/etc/postfix/mysql-virtual-mailbox-domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql-virtual-mailbox-maps.cf virtual_alias_maps = mysql:/etc/postfix/mysql-virtual-alias-maps.cf virtual_transport = dovecot dovecot_destination_recipient_limit = 1 mailbox_command = /usr/lib/dovecot/deliver The *.pem files were created like described in the tutorial above, using Postfix To create a certificate to be used by Postfix use: openssl req -new -x509 -days 3650 -nodes -out /etc/ssl/certs/postfix.pem -keyout /etc/ssl/private/postfix.pem Do not forget to set the permissions on the private key so that no unauthorized people can read it: chmod o= /etc/ssl/private/postfix.pem You will have to tell Postfix where to find your certificate and private key because by default it will look for a dummy certificate file called "ssl-cert-snakeoil": postconf -e smtpd_tls_cert_file=/etc/ssl/certs/postfix.pem postconf -e smtpd_tls_key_file=/etc/ssl/private/postfix.pem I think I don't have to include /etc/dovecot/dovecot.conf here, as login via imaps and pop3s works fine according to the logs. Only problem is making postfix properly use the self-generated, self-signed certificates. Any help appreciated! EDIT: I just tried this different tutorial on generating a self-signed certificate for postfix, still getting the same error. I really don't know what else to test. I also did check for the SSL libraries, but all seems to be fine: root@domain:~# ldd /usr/sbin/postfix linux-vdso.so.1 => (0x00007fff91b25000) libpostfix-global.so.1 => /usr/lib/libpostfix-global.so.1 (0x00007f6f8313d000) libpostfix-util.so.1 => /usr/lib/libpostfix-util.so.1 (0x00007f6f82f07000) libssl.so.0.9.8 => /usr/lib/libssl.so.0.9.8 (0x00007f6f82cb1000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007f6f82910000) libsasl2.so.2 => /usr/lib/libsasl2.so.2 (0x00007f6f826f7000) libdb-4.8.so => /usr/lib/libdb-4.8.so (0x00007f6f8237c000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007f6f82164000) libresolv.so.2 => /lib/libresolv.so.2 (0x00007f6f81f4e000) libc.so.6 => /lib/libc.so.6 (0x00007f6f81beb000) libdl.so.2 => /lib/libdl.so.2 (0x00007f6f819e7000) libz.so.1 => /usr/lib/libz.so.1 (0x00007f6f817d0000) libpthread.so.0 => /lib/libpthread.so.0 (0x00007f6f815b3000) /lib64/ld-linux-x86-64.so.2 (0x00007f6f83581000) After following Ansgar Wiechers instructions its finally working. postconf -n contained the lines as it should. The certificate/key check via openssl did show that both files are valid. So it indeed has been a permissions problem! Didn't know that chown'ing the /etc/ssl/*/postfix.pem files to postfix:postfix is not enough for postfix to read the files.

Read the article

Bandwidth Limit User

- by user45611

Hello, i'm saxtor i would like to know how to limit users bandwidth for 10gb per day however i dont want to limit them by ipaddress because if they where to go to an internet cafe the users at the cafe will be restricted with that quota, i need to log them via sockets, example the user request to download a file from http://localhost with there username and password, when they download the file sql will update there bandwidth they used, i have a script here but its not working my buffer doesnt work that rate when a user uses multiple connections thanks for the help!. /** * @author saxtor if you can improve this code email me @saxtorinc.com * @copyright 2010 / /* * CREATE TABLE IF NOT EXISTS max_traffic ( id int(255) NOT NULL AUTO_INCREMENT, limit int(255) NOT NULL, PRIMARY KEY (id) ) ENGINE=MyISAM DEFAULT CHARSET=latin1 AUTO_INCREMENT=0 ; */ //SQL Connection [this is hackable for testing] date_default_timezone_set("America/Guyana"); mysql_connect("localhost", "root", "") or die(mysql_error()); mysql_select_db("Quota") or die(mysql_error()); function quota($id) { $result = mysql_query("SELECT `limit` FROM max_traffic WHERE id='$id' ") or die(error_log(mysql_error()));; $row = mysql_fetch_array($result); return $row[0]; } function update_quota($id,$value) { $result = mysql_query("UPDATE `max_traffic` SET `limit`='$value' WHERE id='$id'") or die(mysql_error()); return $value; } if ( quota(1) != 0) $limit = quota(1); else $limit = 0; $multipart = false; //was a part of the file requested? (partial download) $range = $_SERVER["HTTP_RANGE"]; if ($range) { //pass client Range header to rapidshare // _insert($range); $cookie .= "\r\nRange: $range"; $multipart = true; header("X-UR-RANGE-Range: $range"); } $url = 'http://127.0.0.1/puppy.iso'; $filename = basename($url); //octet-stream + attachment = client always stores file header('Content-type: application/octet-stream'); header('Content-Disposition: attachment; filename="'.$filename.'"'); //always included so clients know this script supports resuming header("Accept-Ranges: bytes"); //awful hack to pass rapidshare the premium cookie $user_agent = ini_get("user_agent"); ini_set("user_agent", $user_agent . "\r\nCookie: enc=$cookie"); $httphandle = fopen($url, "r"); $headers = stream_get_meta_data($httphandle); $size = $headers["wrapper_data"][6]; $sizer = explode(' ',$size); $size = $sizer[1]; //let's check the return header of rapidshare for range / length indicators //we'll just pass these to the client foreach ($headers["wrapper_data"] as $header) { $header = trim($header); if (substr(strtolower($header), 0, strlen("content-range")) == "content-range") { // _insert($range); header($header); header("X-RS-RANGE-" . $header); $multipart = true; //content-range indicates partial download } elseif (substr(strtolower($header), 0, strlen("Content-Length")) == "content-length") { // _insert($range); header($header); header("X-RS-CL-" . $header); } } if ($multipart) header('HTTP/1.1 206 Partial Content'); flush(); $speed = 4128; $packet = 1; //this is private dont touch. $bufsize = 128; //this is private dont touch/ $bandwidth = 0; //this is private dont touch. while (!(connection_aborted() || connection_status() == 1) && $size > 0) { while (!feof($httphandle) && $size > 0) { if ($limit <= 0 ) $size = 0; if ( $size < $bufsize && $size != 0 && $limit != 0) { echo fread($httphandle,$size); $bandwidth += $size; } else { if( $limit != 0) echo fread($httphandle,$bufsize); $bandwidth += $bufsize; } $size -= $bufsize; $limit -= $bufsize; flush(); if ($speed > 0 && ($bandwidth > $speed*$packet*103)) { usleep(100000); $packet++; //update_quota(1,$limit); } error_log(update_quota(1,$limit)); $limit = quota(1); //if( $size <= 0 ) // exit; } fclose($httphandle); } exit; ?

Read the article

Server Memory with Magento

- by Mohamed Elgharabawy

I have a cloud server with the following specifications: 2vCPUs 4G RAM 160GB Disk Space Network 400Mb/s System Image: Ubuntu 12.04 LTS I am only running Magento CE 1.7.0.2 on this server. Nothing else. Usually, the server has a loading time of 4-5 seconds. Recently, this has dropped to over 30 seconds and sometimes the server just goes away and I get HTTP error reports to my email stating that HTTP requests took more than 20000ms. Running top command and sorting them returns the following: top - 15:29:07 up 3:40, 1 user, load average: 28.59, 25.95, 22.91 Tasks: 112 total, 30 running, 82 sleeping, 0 stopped, 0 zombie Cpu(s): 90.2%us, 9.3%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.3%si, 0.2%st PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31901 www-data 20 0 360m 71m 5840 R 7 1.8 1:39.51 apache2 32084 www-data 20 0 362m 72m 5548 R 7 1.8 1:31.56 apache2 32089 www-data 20 0 348m 59m 5660 R 7 1.5 1:41.74 apache2 32295 www-data 20 0 343m 54m 5532 R 7 1.4 2:00.78 apache2 32303 www-data 20 0 354m 65m 5260 R 7 1.6 1:38.76 apache2 32304 www-data 20 0 346m 56m 5544 R 7 1.4 1:41.26 apache2 32305 www-data 20 0 348m 59m 5640 R 7 1.5 1:50.11 apache2 32291 www-data 20 0 358m 69m 5256 R 6 1.7 1:44.26 apache2 32517 www-data 20 0 345m 56m 5532 R 6 1.4 1:45.56 apache2 30473 www-data 20 0 355m 66m 5680 R 6 1.7 2:00.05 apache2 32093 www-data 20 0 352m 63m 5848 R 6 1.6 1:53.23 apache2 32302 www-data 20 0 345m 56m 5512 R 6 1.4 1:55.87 apache2 32433 www-data 20 0 346m 57m 5500 S 6 1.4 1:31.58 apache2 32638 www-data 20 0 354m 65m 5508 R 6 1.6 1:36.59 apache2 32230 www-data 20 0 347m 57m 5524 R 6 1.4 1:33.96 apache2 32231 www-data 20 0 355m 66m 5512 R 6 1.7 1:37.47 apache2 32233 www-data 20 0 354m 64m 6032 R 6 1.6 1:59.74 apache2 32300 www-data 20 0 355m 66m 5672 R 6 1.7 1:43.76 apache2 32510 www-data 20 0 347m 58m 5512 R 6 1.5 1:42.54 apache2 32521 www-data 20 0 348m 59m 5508 R 6 1.5 1:47.99 apache2 32639 www-data 20 0 344m 55m 5512 R 6 1.4 1:34.25 apache2 32083 www-data 20 0 345m 56m 5696 R 5 1.4 1:59.42 apache2 32085 www-data 20 0 347m 58m 5692 R 5 1.5 1:42.29 apache2 32293 www-data 20 0 353m 64m 5676 R 5 1.6 1:52.73 apache2 32301 www-data 20 0 348m 59m 5564 R 5 1.5 1:49.63 apache2 32528 www-data 20 0 351m 62m 5520 R 5 1.6 1:36.11 apache2 31523 mysql 20 0 3460m 576m 8288 S 5 14.4 2:06.91 mysqld 32002 www-data 20 0 345m 55m 5512 R 5 1.4 2:01.88 apache2 32080 www-data 20 0 357m 68m 5512 S 5 1.7 1:31.30 apache2 32163 www-data 20 0 347m 58m 5512 S 5 1.5 1:58.68 apache2 32509 www-data 20 0 345m 56m 5504 R 5 1.4 1:49.54 apache2 32306 www-data 20 0 358m 68m 5504 S 4 1.7 1:53.29 apache2 32165 www-data 20 0 344m 55m 5524 S 4 1.4 1:40.71 apache2 32640 www-data 20 0 345m 56m 5528 R 4 1.4 1:36.49 apache2 31888 www-data 20 0 359m 70m 5664 R 4 1.8 1:57.07 apache2 32511 www-data 20 0 357m 67m 5512 S 3 1.7 1:47.00 apache2 32054 www-data 20 0 357m 68m 5660 S 2 1.7 1:53.10 apache2 1 root 20 0 24452 2276 1232 S 0 0.1 0:01.58 init Moreover, running free -m returns the following: total used free shared buffers cached Mem: 4003 3919 83 0 118 901 -/+ buffers/cache: 2899 1103 Swap: 0 0 0 To investigate this further, I have installed apache buddy, it recommeneded that I need to reduce the maxclient connections. Which I did. I also installed MysqlTuner and it suggests that I need to set my innodb_buffer_pool_size to = 3.0G. However, I cannot do that, since the whole memory is 4G. Here is the output from apache buddy: ### GENERAL REPORT ### Settings considered for this report: Your server's physical RAM: 4003MB Apache's MaxClients directive: 40 Apache MPM Model: prefork Largest Apache process (by memory): 73.77MB [ OK ] Your MaxClients setting is within an acceptable range. Max potential memory usage: 2950.8 MB Percentage of RAM allocated to Apache 73.72 % And this is the output of MySQLTuner: -------- Performance Metrics ------------------------------------------------- [--] Up for: 47m 22s (675K q [237.552 qps], 12K conn, TX: 1B, RX: 300M) [--] Reads / Writes: 45% / 55% [--] Total buffers: 2.1G global + 2.7M per thread (151 max threads) [OK] Maximum possible memory usage: 2.5G (64% of installed RAM) [OK] Slow queries: 0% (0/675K) [OK] Highest usage of available connections: 26% (40/151) [OK] Key buffer size / total MyISAM indexes: 36.0M/18.7M [OK] Key buffer hit rate: 100.0% (245K cached / 105 reads) [OK] Query cache efficiency: 92.5% (500K cached / 541K selects) [!!] Query cache prunes per day: 302886 [OK] Sorts requiring temporary tables: 0% (1 temp sorts / 15K sorts) [!!] Joins performed without indexes: 12135 [OK] Temporary tables created on disk: 25% (8K on disk / 32K total) [OK] Thread cache hit rate: 90% (1K created / 12K connections) [!!] Table cache hit rate: 17% (400 open / 2K opened) [OK] Open file limit used: 12% (123/1K) [OK] Table locks acquired immediately: 100% (196K immediate / 196K locks) [!!] InnoDB buffer pool / data size: 2.0G/3.5G [OK] InnoDB log waits: 0 -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Read this before increasing table_cache over 64: http://bit.ly/1mi7c4C Variables to adjust: query_cache_size ( 64M) join_buffer_size ( 128.0K, or always use indexes with joins) table_cache ( 400) innodb_buffer_pool_size (= 3G) Last but not least, the server still has more than 60% of free disk space. Now, based on the above, I have few questions: Are these numbers normal? Do they make sense? Do I need to upgrade the server? If I don't need to upgrade and my configuration is not correct, how do I optimize it?

Read the article

Relay Access Denied (State 13) Postfix + Dovecot + Mysql

- by Pierre Jeptha

So we have been scratching our heads for quite some time over this relay issue that has presented itself since we re-built our mail-server after a failed Webmin update. We are running Debian Karmic with postfix 2.6.5 and Dovecot 1.1.11, sourcing from a Mysql database and authenticating with SASL2 and PAM. Here are the symptoms of our problem: 1) When users are on our local network they can send and receive 100% perfectly fine. 2) When users are off our local network and try to send to domains not of this mail server (ie. gmail) they get the "Relay Access Denied" error. However users can send to domains of this mail server when off the local network fine. 3) We host several virtual domains on this mailserver, the primary domain being airnet.ca. The rest of our virtual domains (ex. jeptha.ca) cannot receive email from domains not hosted by this mailserver (ie. gmail and such cannot send to them). They receive bounce backs of "Relay Access Denied (State 13)". This is regardless of whether they are on our local network or not, which is why it is so urgent for us to get this solved. Here is our main.cf from postfix: myhostname = mail.airnet.ca mydomain = airnet.ca smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no smtpd_sasl_type = dovecot queue_directory = /var/spool/postfix smtpd_sasl_path = private/auth smtpd_sender_restrictions = permit_mynetworks permit_sasl_authenticated smtp_sasl_auth_enable = yes smtpd_sasl_auth_enable = yes append_dot_mydomain = no readme_directory = no smtp_tls_security_level = may smtpd_tls_security_level = may smtp_tls_note_starttls_offer = yes smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_auth_only = no alias_maps = proxy:mysql:/etc/postfix/mysql/alias.cf hash:/etc/aliases alias_database = hash:/etc/aliases mydestination = mail.airnet.ca, airnet.ca, localhost.$mydomain mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + local_recipient_maps = $alias_maps $virtual_mailbox_maps proxy:unix:passwd.byname home_mailbox = /var/virtual/ mail_spool_directory = /var/spool/mail mailbox_transport = maildrop smtpd_helo_required = yes disable_vrfy_command = yes smtpd_etrn_restrictions = reject smtpd_data_restrictions = reject_unauth_pipelining, permit show_user_unknown_table_name = no proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $relay_domains $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $transport_maps $mynetworks $virtual_mailbox_limit_maps $virtual_uid_maps $virtual_gid_maps virtual_alias_domains = message_size_limit = 20971520 transport_maps = proxy:mysql:/etc/postfix/mysql/vdomain.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql/vmailbox.cf virtual_alias_maps = proxy:mysql:/etc/postfix/mysql/alias.cf hash:/etc/mailman/aliases virtual_uid_maps = proxy:mysql:/etc/postfix/mysql/vuid.cf virtual_gid_maps = proxy:mysql:/etc/postfix/mysql/vgid.cf virtual_mailbox_base = / virtual_mailbox_limit = 209715200 virtual_mailbox_extended = yes virtual_create_maildirsize = yes virtual_mailbox_limit_maps = proxy:mysql:/etc/postfix/mysql/vmlimit.cf virtual_mailbox_limit_override = yes virtual_mailbox_limit_inbox = no virtual_overquote_bounce = yes virtual_minimum_uid = 1 maximal_queue_lifetime = 1d bounce_queue_lifetime = 4h delay_warning_time = 1h append_dot_mydomain = no qmgr_message_active_limit = 500 broken_sasl_auth_clients = yes smtpd_sasl_path = private/auth smtpd_sasl_local_domain = $myhostname smtpd_sasl_security_options = noanonymous smtpd_sasl_authenticated_header = yes smtp_bind_address = 142.46.193.6 relay_domains = $mydestination mynetworks = 127.0.0.0, 142.46.193.0/25 inet_interfaces = all inet_protocols = all And here is the master.cf from postfix: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - - - - smtpd #submission inet n - - - - smtpd # -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #smtps inet n - - - - smtpd # -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING #628 inet n - - - - qmqpd pickup fifo n - - 60 1 pickup cleanup unix n - - - 0 cleanup qmgr fifo n - n 300 1 qmgr #qmgr fifo n - - 300 1 oqmgr tlsmgr unix - - - 1000? 1 tlsmgr rewrite unix - - - - - trivial-rewrite bounce unix - - - - 0 bounce defer unix - - - - 0 bounce trace unix - - - - 0 bounce verify unix - - - - 1 verify flush unix n - - 1000? 0 flush proxymap unix - - n - - proxymap proxywrite unix - - n - 1 proxymap smtp unix - - - - - smtp # When relaying mail as backup MX, disable fallback_relay to avoid MX loops relay unix - - - - - smtp -o smtp_fallback_relay= # -o smtp_helo_timeout=5 -o smtp_connect_timeout=5 showq unix n - - - - showq error unix - - - - - error retry unix - - - - - error discard unix - - - - - discard local unix - n n - - local virtual unix - n n - - virtual lmtp unix - - - - - lmtp anvil unix - - - - 1 anvil scache unix - - - - 1 scache maildrop unix - n n - - pipe flags=DRhu user=vmail argv=/usr/bin/maildrop -d ${recipient} # # See the Postfix UUCP_README file for configuration details. # uucp unix - n n - - pipe flags=Fqhu user=uucp argv=uux -r -n -z -a$sender - $nexthop!rmail ($recipient) # # Other external delivery methods. # ifmail unix - n n - - pipe flags=F user=ftn argv=/usr/lib/ifmail/ifmail -r $nexthop ($recipient) bsmtp unix - n n - - pipe flags=Fq. user=bsmtp argv=/usr/lib/bsmtp/bsmtp -t$nexthop -f$sender $recipient scalemail-backend unix - n n - 2 pipe flags=R user=scalemail argv=/usr/lib/scalemail/bin/scalemail-store ${nexthop} ${user} ${extension} mailman unix - n n - - pipe flags=FR user=list argv=/usr/lib/mailman/bin/postfix-to-mailman.py ${nexthop} ${user} spfpolicy unix - n n - - spawn user=nobody argv=/usr/bin/perl /usr/sbin/postfix-policyd-spf-perl smtp-amavis unix - - n - 4 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes #127.0.0.1:10025 inet n - n - - smtpd dovecot unix - n n - - pipe flags=DRhu user=dovecot:21pever1lcha0s argv=/usr/lib/dovecot/deliver -d ${recipient Here is Dovecot.conf protocols = imap imaps pop3 pop3s disable_plaintext_auth = no log_path = /etc/dovecot/logs/err info_log_path = /etc/dovecot/logs/info log_timestamp = "%Y-%m-%d %H:%M:%S ". syslog_facility = mail ssl_listen = 142.46.193.6 ssl_disable = no ssl_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem ssl_key_file = /etc/ssl/private/ssl-cert-snakeoil.key mail_location = mbox:~/mail:INBOX=/var/virtual/%d/mail/%u mail_privileged_group = mail mail_debug = yes protocol imap { login_executable = /usr/lib/dovecot/imap-login mail_executable = /usr/lib/dovecot/rawlog /usr/lib/dovecot/imap mail_executable = /usr/lib/dovecot/gdbhelper /usr/lib/dovecot/imap mail_executable = /usr/lib/dovecot/imap imap_max_line_length = 65536 mail_max_userip_connections = 20 mail_plugin_dir = /usr/lib/dovecot/modules/imap login_greeting_capability = yes } protocol pop3 { login_executable = /usr/lib/dovecot/pop3-login mail_executable = /usr/lib/dovecot/pop3 pop3_enable_last = no pop3_uidl_format = %08Xu%08Xv mail_max_userip_connections = 10 mail_plugin_dir = /usr/lib/dovecot/modules/pop3 } protocol managesieve { sieve=~/.dovecot.sieve sieve_storage=~/sieve } mail_plugin_dir = /usr/lib/dovecot/modules/lda auth_executable = /usr/lib/dovecot/dovecot-auth auth_process_size = 256 auth_cache_ttl = 3600 auth_cache_negative_ttl = 3600 auth_username_chars = abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ01234567890.-_@ auth_verbose = yes auth_debug = yes auth_debug_passwords = yes auth_worker_max_count = 60 auth_failure_delay = 2 auth default { mechanisms = plain login passdb sql { args = /etc/dovecot/dovecot-sql.conf } userdb sql { args = /etc/dovecot/dovecot-sql.conf } socket listen { client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } master { path = /var/run/dovecot/auth-master mode = 0600 } } } Please, if you require anything do not hesistate, I will post it ASAP. Any help or suggestions are greatly appreciated! Thanks, Pierre

Read the article

OSX Server 3, Mac clients binding to OD and Profile Manager failing

- by dbf

I've made a setup containing a Mac Mini with OSX Server 3 (Mavericks 10.9.2) using Open Directory and Profile Manager (Mail, etc all set up and working). Now the thing is, internally on the local network, everything works great. Clients can bind to the OD and the users are able to login. I can install trust and settings profiles (either custom or group profiles) and all services in the profiles mentioned are being configured correctly. I can log in and out, hump around and do it a 100 times on different macs with different users, it works. My goal is to make this service publicly. The domain is with a FQDN which I own, for simplicity let's say server.domain.com. Now the only way for me to bind the clients to the OD is using LDAP mapping RCF2307 (without SSL) and a DN suffix of dc=server,dc=domain,dc=com using the Directory Utility. The options from server, or open directory will throw several errors like Connection failed to node '/LDAPv3/server.domain.com (2100). First of all I don't really understand the problem why clients can't bind to the OD like it does locally, with and without SSL (all ports are open, literally all ports are open, not just 389,636 and 1640, wasn't sure if I was missing any). When the clients are using LDAP mapping RFC2307 to bind (without SSL only), clients are able to authenticate, login and even load the Trust profile. But every Settings profile will fail with a Debug Message: Unable to find GUID in user record OD or fail to install saying missing user identification. Is there any way to get this to work without RFC2307? Because there is quite some stuff missing when using RFC2307 and not pull the mapping from the server or use open directory. Is this setup even possible? Or should I use VPN to authenticate with the OD? The network setup is a Modem/Router (DHCP off) with WAN NATted to an Airport Extreme (Using DHCP+NAT). The AE does notify with a double NAT message but I haven't had any problems with it on any other service. So WAN - 192.168.2.220 (static), AE - 10.0.1.* (dhcp) Output of DIG from the outside using dig server.domain.com ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.domain.com. IN A ;; ANSWER SECTION: server.domain.com. 77 IN A 91.50.*.* (valid WAN IP) ;; SERVER 172.*.*.1#53(172.*.*.1) (iPhone) DIG locally from a client and server (same output) ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 2, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.domain.com. IN A ;; ANSWER SECTION: server.domain.com. 10800 IN A 10.0.1.11 ;; AUTHORITY SECTION: server.domain.com. 10800 IN NS domain.com. (used for email send in relay) server.domain.com. 10800 IN NS server.domain.com. ;; SERVER 10.0.1.11#53(10.0.1.11) Are there any things I should check? Only have OSX. -- double NAT issue, plugged in the server directly on the Modem/Router with a static IP and issue remains. Guess that rules out the double NAT thing. -- changeip -checkhostname comes with There is nothing to change, e.g. success. Primary address = 10.0.1.11 Current HostName = server.domain.com DNS HostName = server.domain.com For now, I've made a workaround by using an admin account that forces a permanent VPN connection on boot. That means before it comes to the login, a connection is already made or underway. I will continue this post when I have more time, also locating all the necessary .log files of each application involved. I have some suspicions but have to debug a bit more when I have more time on my hands .. Unless, of course, I get sidetracked with having a life. Which is arguably not very likely. krypted.com

Read the article

Set up linux box for hosting a-z

- by microchasm

I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP/MySQL: To upgrade PHP and MySQL to the latest versions, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! Add IUS repository to our package manager cd /tmp wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. # list all the packages in the IUS repository; use this to find PHP/MySQL version and libraries you want to install Remove old version of PHP and install newer version from IUS rpm -qa | grep php # to list all of the installed php packages we want to remove yum shell # open an interactive yum shell remove php-common php-mysql php-cli #remove installed PHP components install php53 php53-mysql php53-cli php53-common #add packages you want transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) Upgrade MySQL from IUS repository /etc/init.d/mysqld stop rpm -qa | grep mysql # to see installed mysql packages yum shell remove mysql mysql-server #remove installed MySQL components install mysql51 mysql51-server mysql51-devel transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell service mysqld start mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project Upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Install rssh (restricted shell) to provide scp and sftp access, without allowing ssh login cd /tmp wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm useradd -m -d /home/dev -s /usr/bin/rssh dev passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. vi /etc/rssh.conf Uncomment or add: allowscp allowsftp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). rssh instructions appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html Set up virtual interfaces ifconfig eth1:1 192.168.1.3 up #start up the virtual interface cd /etc/sysconfig/network-scripts/ cp ifcfg-eth1 ifcfg-eth1:1 #copy default script and match name to our virtual interface vi ifcfg-eth1:1 #modify eth1:1 script #ifcfg-eth1:1 | modify so it looks like this: DEVICE=eth1:1 IPADDR=192.168.1.3 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes NAME=eth1:1 Add more Virtual interfaces as needed by repeating. Because of the ONBOOT=yes line in the ifcfg-eth1:1 file, this interface will be brought up when the system boots, or the network starts/restarts. service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Bringing up interface eth1: [ OK ] ping 192.168.1.3 64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.105 ms And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

Read the article

Using wget to download pdf files from a site that requires cookies to be set

- by matt74tm

I want to access a newspaper site and then download their epaper copies (in PDF). The site requires me to login using my email address and password and then it permits me to access those PDF URLs. I'm having trouble 'setting my session' in wget. When I login into the site from my browser, it sets two cookie values: [email protected] Password=12345 I tried: wget --post-data "[email protected]&Password=12345" http://epaper.abc.com/login.aspx However, that just downloaded the login page and saved it locally The FORM on the login page has two fields: txtUserID txtPassword and radiobuttons like this: <input id="rbtnManchester" type="radio" checked="checked" name="txtpub" value="44"> Another button: <input id="rbtnLondon" type="radio" name="txtpub" value="64"> If I post this to the login.aspx page, I get the same output wget --post-data "[email protected]&txtPassword=12345&txtpub=44" http://epaper.abc.com/login.aspx If I do: --save-cookies abc_cookies.txt it doesnt seem to have anything other than the default content. For the last if I do --debug as well it says: ... Set-Cookie: ASP.NET_SessionId=05kphcn4hjmblq45qgnjoe41; path=/; HttpOnly ... Stored cookie epaper.abc.com -1 (ANY) / <session> <insecure> [expiry none] ASP.NET_SessionId 05kphcn4hjmblq45qgnjoe41 Length: 107253 (105K) [text/html] Saving to: `login.aspx' ... Saving cookies to abc_cookies.txt. However, abc_cookies.txt shows ONLY the following: # HTTP cookie file. # Generated by Wget on 2011-08-16 08:03:05. # Edit at your own risk. (Not sure why I'm not getting any responses on SO - perhaps SU is a better forum - http://stackoverflow.com/questions/7064171/using-wget-to-download-pdf-files-from-a-site-that-requires-cookies-to-be-set) EDIT 1 C:\Temp>wget --cookies=on --keep-session-cookies --save-cookies abc_cookies.txt --post-data "txtUserID=abc%40gmail.com&txtPassword=password&txtpub=44&chkbox=checkbox&submit.x=48&submit.y=7" http://epaper.abc.com/login.aspx --debug SYSTEM_WGETRC = c:/progra~1/wget/etc/wgetrc syswgetrc = C:\Program Files (x86)\GnuWin32/etc/wgetrc DEBUG output created by Wget 1.11.4 on Windows-MinGW. --2011-08-18 08:15:59-- http://epaper.abc.com/login.aspx Resolving epaper.abc.com... seconds 0.00, 999.999.99.99 Caching epaper.abc.com => 999.999.99.99 Connecting to epaper.abc.com|999.999.99.99|:80... seconds 0.00, connected. Created socket 300. Releasing 0x00a2ae80 (new refcount 1). ---request begin--- POST /login.aspx HTTP/1.0 User-Agent: Wget/1.11.4 Accept: */* Host: epaper.abc.com Connection: Keep-Alive Content-Type: application/x-www-form-urlencoded Content-Length: 100 ---request end--- [POST data: txtUserID=abc%40gmail.com&txtPassword=password&txtpub=44&chkbox=checkbox&submit.x=48&submit.y=7] HTTP request sent, awaiting response... ---response begin--- HTTP/1.1 200 OK Connection: keep-alive Date: Thu, 18 Aug 2011 02:46:17 GMT Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET X-AspNet-Version: 2.0.50727 Set-Cookie: ASP.NET_SessionId=owcrje55yl45kgmhn43gq145; path=/; HttpOnly Cache-Control: private Content-Type: text/html; charset=utf-8 Content-Length: 107253 ---response end--- 200 OK Registered socket 300 for persistent reuse. Stored cookie epaper.abc.com -1 (ANY) / <session> <insecure> [expiry none] ASP.NET_SessionId owcrje55yl45kgmhn43gq145 Length: 107253 (105K) [text/html] Saving to: `login.aspx.1' 100%[======================================================================================================================>] 107,253 24.9K/s in 4.2s 2011-08-18 08:16:05 (24.9 KB/s) - `login.aspx.1' saved [107253/107253] Saving cookies to abc_cookies.txt. Done saving cookies. C:\Temp>wget --referer=http://epaper.abc.com/login.aspx --cookies=on --load-cookies abc_cookies.txt --keep-session-cookies --save-cookies abc_cookies.txt http://epaper.abc.com/PagePrint/16_08_2011_001.pdf --debug SYSTEM_WGETRC = c:/progra~1/wget/etc/wgetrc syswgetrc = C:\Program Files (x86)\GnuWin32/etc/wgetrc DEBUG output created by Wget 1.11.4 on Windows-MinGW. Stored cookie epaper.abc.com -1 (ANY) / <session> <insecure> [expiry none] ASP.NET_SessionId owcrje55yl45kgmhn43gq145 --2011-08-18 08:16:12-- http://epaper.abc.com/PagePrint/16_08_2011_001.pdf Resolving epaper.abc.com... seconds 0.00, 999.999.99.99 Caching epaper.abc.com => 999.999.99.99 Connecting to epaper.abc.com|999.999.99.99|:80... seconds 0.00, connected. Created socket 300. Releasing 0x00598290 (new refcount 1). ---request begin--- GET /PagePrint/16_08_2011_001.pdf HTTP/1.0 Referer: http://epaper.abc.com/login.aspx User-Agent: Wget/1.11.4 Accept: */* Host: epaper.abc.com Connection: Keep-Alive Cookie: ASP.NET_SessionId=owcrje55yl45kgmhn43gq145 ---request end--- HTTP request sent, awaiting response... ---response begin--- HTTP/1.1 200 OK Connection: keep-alive Date: Thu, 18 Aug 2011 02:46:30 GMT Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET X-AspNet-Version: 2.0.50727 content-disposition: attachement; filename=Default_logo.gif Cache-Control: private Content-Type: image/GIF Content-Length: 4568 ---response end--- 200 OK Registered socket 300 for persistent reuse. Length: 4568 (4.5K) [image/GIF] Saving to: `16_08_2011_001.pdf' 100%[======================================================================================================================>] 4,568 7.74K/s in 0.6s 2011-08-18 08:16:14 (7.74 KB/s) - `16_08_2011_001.pdf' saved [4568/4568] Saving cookies to abc_cookies.txt. Done saving cookies. Contents of abc_cookies.txt epaper.abc.com FALSE / FALSE 0 ASP.NET_SessionId owcrje55yl45kgmhn43gq145

Read the article

Managing BES Software Configurations

- by DaveJohnston

Hi, I am having problems with OTA deployment of a bespoke application that we have written. I have read loads of threads elsewhere and I have got mixed help, but for my particular case none of it has really helped. So I thought I would explain my exact situation and try and get some help here. I am running BES version 4.1.5 (Bundle 79) for Microsoft Exchange. The application we have written is split into 5 modules, which we control, and another 4 modules which are 3rd party libraries that we require. So for our modules the version numbers are regularly changing but for the others they are pretty much always going to remain the same. We have an alx file set up that identifies all of the files required and in fact I am able to create a software configuration and deploy the application with no problems. What I am trying to do however is maintain multiple versions of our application on the BES and be able to select which version I want to deploy to each user. I have tried this a number of ways (as I said I have read lots of other threads with solutions to this problem) but each seems to come with its own problem. First of all I tried just creating different configurations for each version of the application, but because they each had the same application ID the BES informed me that I couldn't do this. I read somewhere that the solution was to create a second shared folder (e.g. \Program Files\Common Files\RIM) and add the apploader stuff and the new version of the app to this folder. I could then create a second software configuration that would have the same application ID. The result of this seemed promising to start with. When I changed the config that was assigned to a user the new version was pushed out fine. But afterwards the BES reported that the device state was invalid, which meant I couldn't push anything else until I reactivated the device. I guess this is because the first config was never set to disallowed so the old version wasn't removed and the device essentially reported that it had multiple versions of the same application installed. The next suggestion I got was to change the application ID for each version, e.g. to include the version number. This meant that each version of the application could be included in a single configuration and I could set one to disallowed and the other to required. Initially this worked and the first version was deployed. But when I switched (i.e. the old version became disallowed and the new version required) the BES reported upgrade required and removed the old version. The device restarts and the old version is gone but the new version is not pushed out. I checked the BES and it still said Upgrade Required. I checked the log files and found: [40000] (11/12 09:50:27.397):{0xEB8} {[email protected], PIN=1234, UserId=2}SCS::PollDBQueueNewRequests - Queuing POLL_FOR_MISSING_APPS request [40000] (11/12 09:50:28.241):{0xE9C} RequestHandler::PollForMissingApps: Starting Poll For Missing Apps. [40304] (11/12 09:50:28.241):{0xE90} WorkerThreadPool:: ThreadProc(): Thread released with empty queue [40000] (11/12 09:50:28.241):{0xE9C} SCS::RemoveAppDeliveryRequests - No App Delivery Requests purged for User id 2 [30000] (11/12 09:50:28.960):{0xE9C} Discard duplicate module group "name" on device [30000] (11/12 09:50:28.960):{0xE9C} Discard duplicate module group "name" on device [40000] (11/12 09:50:29.163):{0xE9C} RequestHandler::PollForMissingApps: Completed Poll For Missing Apps, elapsed time 0.922 seconds. (You will notice I have removed actual names and email addresses etc for privacy reasons. But one question: where does the name of the module group come from? In my case it is close to the application ID but doesn't include the version number that I added at the end in order to get it to work. Is that information embedded in a COD file or something??) So it is reporting a duplicate module group on the device? What does this mean? I checked the device properties (as reported on the BES) and it confirms that the modules with the old version numbers are still present on the device. So the application has been removed but not the modules?? I checked the device and the modules are gone, so it is just the BES reporting that they are still there?? I checked the database and it has the modules in questions in the SyncDeviceMgmt table. If I delete these from the DB the BES changes to report Install Required, and low and behold the new version of the app is pushed out. So at the end of all that, my question is: does anyone have any other suggestions of how to handle upgrading our bespoke application OTA from the BES? Or can anyone point out something I am doing wrong in what I described above that might solve the problems I am having? I guess the question is why does the database maintain that the modules are on the device after they are removed? Thanks for any help you can provide.

Read the article

IPV6 causing issue with DNS

- by Mike Wells

I have set up an 'internal' DNS at my work, basically we have ourdomain.com that is for internet, email etc and I have created on one of our linux network servers (debian) a DNS using bind9 with the domain ourdomain.inc. So based on my files below and the symptoms I'm describing; what effect could IPV6 be having on my setup? What can I do to fix this? I assume it is not actually the IPV6 causing the issue, but rather something in my setup. These are the critical (I think) files I have modified: named.conf.local zone "ourdomain.inc" { type master; file "/etc/bind/zones/ourdomain.inc.db"; }; zone "201.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.201.168.192.in-addr.arpa"; }; named.conf.options options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. forwarders { 1.2.3.4; //IP of our external DNS provider }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; ourdomain.inc.db $TTL 86400 ourdomain.inc. IN SOA ns1.ipower.com. admin.ourdomain.inc. ( 2006081401 28800 3600 604800 38400 ) serv1 IN A 192.168.201.223 serv2 IN A 192.168.201.220 serv3 IN A 192.168.201.219 ns1.ipower.com. IN A 1.2.3.4 ns2.ipower.com. IN A 1.2.3.5 @ IN NS ns1.ipower.com. @ IN NS ns2.ipower.com. svn IN CNAME serv1 docs IN CNAME serv2 jira IN CNAME serv3 confluence IN CNAME serv3 fisheye IN CNAME serv3 rev.201.168.192.in-addr.arpa $TTL 86400 201.168.192.in-addr.arpa. IN SOA ns1.ipower.com. admin.ourdomain.inc. ( 2006081401; 28800; 604800; 604800; 86400 ) 223 IN PTR serv1 @ IN NS ns1.ipower.com. @ IN NS ns2.ipower.com. named.conf include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; I then made our internal DNS my preferred DNS with the two external DNSs the next in-line. More the most part this seems to work, I can ping svn.ourdomain.inc and it resolves to the correct IP, I can also ping google.com and it also resolves no problem. So all seem good. However, periodically (couple of times a day at least), I loose the ability to ping the svn.domain.inc (and all others defined under the internal DNS). What seem to fix the issue temporarily is to disable IPV6 on the network adapter of the client machine and then re-enable it. Then it works for a bit but will always fail again. System Info Internal DNS Distributor ID: Debian Description: Debian GNU/Linux 6.0.6 (squeeze) Release: 6.0.6 Codename: squeeze Linux 2.6.32-5-686 i686 BIND 9.7.3 PC OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7601 Service Pack 1 Build 7601 System Type: x64-based PC Network Card(s): 2 NIC(s) Installed. [01]: Realtek PCIe GBE Family Controller Connection Name: WORK LAN DHCP Enabled: No IP address(es) [01]: the.ipv4.address [02]: the:ipv6:address The question... So based on my files above and the symptoms I described; what effect could IPV6 be having on my setup? What can I do to fix this? I assume it is not actually the IPV6 causing the issue, but rather something in my setup.

Read the article

System Center 2012 Service Manager change request status stuck at new

- by Chuck Herrington

The guy that built and setup this system left rather abruptly and I've taken over. My current issues are I have several change requests that are stuck at New. They do not move to Pending or In Progress. The system is not sending emails when incidents are getting assigned to people. This used to work on this system. I have done a lot of searching and the usual solution to this of stopping and restarting the system center services does not help. Can anyone give me any ideas of where else to look? Update: From all the searching I have done it seemed like I was at the point of re-installing. My initial installation of SCSM 2012 was on a machine that was upgraded from SCSM 2010 and also hosted SCCM 2007 and WSUS. We decided to give it a fresh start on a new server by installing a second instance of the SCSM server on a brand new 2008 R2 server then promoting the new server to the workflow master using the procedures outlined in this article - Dealing with Multiple management Servers. I've gotten to the point where we have both the old and the new server up and the new server has been promoted. I had hopped to get spammed by emails all the sudden due to the workflow taking off, but no such luck. Once all the clients are reconfigured to point to the new server we still plan to decommission the old server but at this point it seems to be that the problem is in the database. Short of any other input from the community, my next plan is to install a 180 day trial on a test server, complete with a separate database so that I can do a side by side comparison between a completely fresh install and what I have now and see if I can find any differences. While that install is running I also plan on investigating the event logs to see if there is anything in there that can shed some light on what is happening on the new server. Update 2: So I've now got a test SCSM server up with a completely fresh install including Database and it seems to be able to transition Change Requests from New to In Progress. I'm attempting to find differences between the two. Stay Tuned! Update 3: In looking through the event log on the new SCSM machine i discovered: Log Name: Operations Manager Source: OpsMgr Root Connector Date: 10/9/2013 3:48:18 PM Event ID: 28000 Task Category: None Level: Warning Keywords: Classic User: N/A Computer: scsm02 Description: The Root connector received an exception from the SDK Service while submitting task status: Cannot set availability on a health service that doesn't exist. This lead me to Event ID 2800 logged after installing secondary server for System Center 2012 Service Manager SP1. I contacted MS to obtain the hotfix, BIG warning here, turns out the hotfix is not so "hot". In order to apply this hotfix, you have to uninstall then reinstall using the files they supply. :( This is where I am at now ... Update 4: Not much luck after the re-install. The errors in the event log have gone away on the new server but the workflows still aren't running and neither the event log nor the workflow status screen seem to indicate why. I've done a comparison of the Activity and the Change Request Event Workflows and I've removed everything from the production system that is not in my fresh test system (which is everything), shut down the services, cleared out the cache folders and restarted the services and still no joy. At the moment the only thing I can think to do is either a)nuke the entire system including the database and start over, losing all of our data in the process or b)contact MS (which is probably going to cost us a butt load of money and time in the end to only advise us to do the same thing. Maybe more idea's will come after coffee ... No answers came after coffee. Attempting to contact MS. Managed to get to their first line of defense, gave them our SA number and someone is supposed to call me back. I am trying to log into my incident on their site to update my ticket with the link to this thread but when i click on the link in the email they sent me it goes to a "Sorry, the page you requested is not available" page ... Linux is looking better and better all the time.

Read the article

Linux/Apache performance very slow even on local network

- by klausch

I have an Ubuntu server machine running Apache and MYSQL. System and version info is as follows: Linux kernel 3.0.0.-12 Apache/2.2.20 MySQL Ver 14.14.Distrib 5.1.58 I am running a few websites on this server, some HTML only, some PHP/MySQL. THe [problem is that response time is very slow, both on static as well as the dynamic sites. Sometimes it takes more than 10 seconds before a response is given, this makes the sites very slow and almost unusable. The problem occurs even when requesting from the local network. I have added the involved subdomains to my /etc/hosts file, and abolve all the problem is not solved by using IP numbers instead of URL's. So there is no DNS lookup issue. I have modified the log format by showing the response times and sometimes a files takes 12 seconds to be served, see the jquery~.js file in the example screenshot. I have no explanation for this extremely long response time, but is is not even the only issue here, some other files takes a long time to be served too, but do not show a long response time in the log file. So probably different tissues are involved here. I cannot find a solution until now, any suggestions??? THanx in advance, Klaas link to screenshot picture from access logfile Some extra configuration info: apache2.conf (comment is removed) LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_event_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType text/plain HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn Include mods-enabled/*.load Include mods-enabled/*.conf Include httpd.conf Include ports.conf LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\" %T/%D" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include conf.d/ Include sites-enabled/ And the virtual hostfile for one of the slow sites, in fact it is pretty straightforward... <VirtualHost *:80> ServerAdmin [email protected] ServerSignature EMail ServerName toenjoy.drsklaus.nl DocumentRoot /var/www/toenjoy.drsklaus.nl <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/toenjoy.drsklaus.nl/> Options Indexes FollowSymLinks MultiViews AllowOverride AuthConfig AuthType Basic AuthName "To Enjoy" AuthUserFile /etc/.htpasswd Require user petraaa Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> And the output of free -m: klaas@ubuntu-server:/etc/apache2$ free -m total used free shared buffers cached Mem: 1997 1401 595 0 144 1017 -/+ buffers/cache: 238 1758 Swap: 2035 0 2035 and I have no indication that swapping occurs on the moments the site is slow. I have runned top and it does not appear to be a CPU issue. I have the impression that the spawning of a apache thread could maybe be the bottleneck but it is just a suggestion. Maybe this gives some extra information! EDIT: The problem seemed to be gone for some time but occurs again! And not only with Apache, also connecting using SSH takes a tremendous time, sometimes it takes up to 15 seconds before the keyphrase is asked for. Also scp works very slowly. The behavious is really unpredoctable and makes the server very hard to use. Any ideas...?

Read the article

Split a long JSON string into lines in Ruby

- by David J.

Read the article

EWS - How to search for items [message] between dates ?

- by SomFred

Hi, I am trying to search for message items between two dates from the inbox folder. I use the following restrictionType but it throws this error: firmt.RootFolder = null What am I doing wrong? There is some messages between the mentionned dates ;-) Thanks for your suggestions. using (ExchangeServiceBinding esb = new ExchangeServiceBinding()) { esb.Url = ConfigurationManager.AppSettings["ExchangeWebServicesURL"].ToString(); esb.RequestServerVersionValue = new RequestServerVersion(); esb.RequestServerVersionValue.Version = ExchangeVersionType.Exchange2007_SP1; esb.PreAuthenticate = true; esb.Credentials = new NetworkCredential(email, password); FindItemType findItemRequest = new FindItemType(); // paging IndexedPageViewType ipvt = new IndexedPageViewType(); ipvt.BasePoint = IndexBasePointType.Beginning; ipvt.MaxEntriesReturned = nombreMessage; ipvt.MaxEntriesReturnedSpecified = true; ipvt.Offset = offset; findItemRequest.Item = ipvt; // filter by dates AndType andType = new AndType(); List<SearchExpressionType> searchExps = new List<SearchExpressionType>(); RestrictionType restriction = new RestrictionType(); PathToUnindexedFieldType pteft = new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.itemDateTimeSent }; IsGreaterThanOrEqualToType IsGreaterThanOrEqualTo = new IsGreaterThanOrEqualToType { Item = pteft, FieldURIOrConstant = new FieldURIOrConstantType { Item = new ConstantValueType { Value = DateTime.Today.AddDays(-6d).ToString() } } }; searchExps.Add(IsGreaterThanOrEqualTo); IsLessThanOrEqualToType IsLessThanOrEqualTo = new IsLessThanOrEqualToType { Item = pteft, FieldURIOrConstant = new FieldURIOrConstantType { Item = new ConstantValueType { Value = DateTime.Today.AddDays(1d).ToString() } } }; searchExps.Add(IsLessThanOrEqualTo); andType.Items = searchExps.ToArray(); restriction.Item = andType; findItemRequest.Restriction = restriction; //// Define the sort order of items. FieldOrderType[] fieldsOrder = new FieldOrderType[1]; fieldsOrder[0] = new FieldOrderType(); PathToUnindexedFieldType dateOrder = new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.itemDateTimeReceived }; fieldsOrder[0].Item = dateOrder; fieldsOrder[0].Order = SortDirectionType.Descending; findItemRequest.SortOrder = fieldsOrder; findItemRequest.Traversal = ItemQueryTraversalType.Shallow; // define which item properties are returned in the response findItemRequest.ItemShape = new ItemResponseShapeType { BaseShape = DefaultShapeNamesType.IdOnly }; // identify which folder to search DistinguishedFolderIdType[] folderIDArray = new DistinguishedFolderIdType[1]; folderIDArray[0] = new DistinguishedFolderIdType { Id = DistinguishedFolderIdNameType.inbox }; // add folders to request findItemRequest.ParentFolderIds = folderIDArray; // find the messages FindItemResponseType findItemResponse = esb.FindItem(findItemRequest); //------------- ArrayOfResponseMessagesType responseMessages = findItemResponse.ResponseMessages; ResponseMessageType responseMessage = responseMessages.Items[0]; if (responseMessage is FindItemResponseMessageType) { FindItemResponseMessageType firmt = (responseMessage as FindItemResponseMessageType); *******FindItemParentType fipt = firmt.RootFolder;******** object obj = fipt.Item; // FindItem contains an array of items. ArrayOfRealItemsType realitems = (obj as ArrayOfRealItemsType); ItemType[] items = realitems.Items; // if no messages were found, then return null -- we're done if (items == null || items.Count() <= 0) return null; // FindItem never gets "all" the properties, so now that we've found them all, we need to get them all. BaseItemIdType[] itemIds = new BaseItemIdType[items.Count()]; for (int i = 0; i < items.Count(); i++) itemIds[i] = items[i].ItemId; GetItemType getItemType = new GetItemType { ItemIds = itemIds, ItemShape = new ItemResponseShapeType { BaseShape = DefaultShapeNamesType.AllProperties, BodyType = BodyTypeResponseType.Text, BodyTypeSpecified = true, AdditionalProperties = new BasePathToElementType[] { new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.itemDateTimeSent }, new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.messageFrom }, new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.messageIsRead }, new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.messageSender }, new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.messageToRecipients }, new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.messageCcRecipients }, new PathToUnindexedFieldType { FieldURI = UnindexedFieldURIType.messageBccRecipients } } } }; GetItemResponseType getItemResponse = esb.GetItem(getItemType); messages = ReadItems(getItemResponse, items.Count()); }

Read the article

Rails Rake Error with XAMPP mysql database

- by edu222

I have installed XAAMP on my win7 machine and I have the apache server/mysql running on there. I set up rails to work with XAmpp as described here: XAMPP and RAILS This tutorial advises you to add this code to the XAMPP httpd.connf : Listen 3000 LoadModule rewrite_module modules/mod_rewrite.so ################################# # RUBY SETUP ################################# <virtualHost *:3000> ServerName rails DocumentRoot "c:/xampp/htdocs/FirstProject/public" <Directory "c:/xampp/htdocs/FirstProject/public/"> Options ExecCGI FollowSymLinks AllowOverride all Allow from all Order allow,deny AddHandler cgi-script .cgi AddHandler fastcgi-script .fcgi </Directory> </VirtualHost> ################################# # RUBY SETUP ################################# Xampp runs on the default localhost and mysql remains unchanged without a pw. I created a rails app with a mysql database like this: rails -d mysql C:/xampp/htdocs/FirstProject Then I started the ruby script/server from within the FirstProject location The localhost:3000/ shows the classic rails welcome I then ran a basic scaffold command: ruby script/generate scaffold FirstProject name:string email:string <br/> When I run the rake db:migrate command I get the following error: C:\xampp\htdocs\FirstProject>rake db:migrate --trace (in C:/xampp/htdocs/FirstProject) ** Invoke db:migrate (first_time) ** Invoke environment (first_time) ** Execute environment ** Execute db:migrate rake aborted! undefined method `init' for Mysql:Class C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/mysql_adapter.rb:70:in `mysql_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:223:in `send' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:223:in `new_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:245:in `checkout_new_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:188:in `checkout' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:184:in `loop' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:184:in `checkout' C:/Ruby/lib/ruby/1.8/monitor.rb:242:in `synchronize' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:183:in `checkout' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:98:in `connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:326:in `retrieve_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_specification.rb:123:in `retrieve_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_specification.rb:115:in `connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/migration.rb :435:in `initialize' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/migration.rb :400:in `new' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/migration.rb :400:in `up' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/migration.rb :383:in `migrate' C:/Ruby/lib/ruby/gems/1.8/gems/rails-2.3.5/lib/tasks/databases.rake:116 C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `call' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `execute' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `each' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `execute' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:597:in `invoke_with_call_c hain' C:/Ruby/lib/ruby/1.8/monitor.rb:242:in `synchronize' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_c hain' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:583:in `invoke' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2051:in `invoke_task' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `top_level' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `each' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `top_level' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in `standard_exceptio n_handling' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2023:in `top_level' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2001:in `run' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in `standard_exceptio n_handling' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:1998:in `run' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/bin/rake:31 C:/Ruby/bin/rake:19:in `load' C:/Ruby/bin/rake:19 Any idea on how to fix this? Thanks in advance

Read the article

alert(line) alerts 'ac' and typeof(line) is 'string', but charAt is not a function

- by Delirium tremens

alert(line) alerts 'ac' typeof(line) is 'string' When I run line.charAt(0), charAt is not a function. When line is 'http://www.google.com/', it works, I think it's the UTF-8 encoding of the file that I opened... How to make charAt work with UTF-8? UPDATED: http://mxr.mozilla.org/mozilla-central/source/netwerk/dns/src/effective_tld_names.dat?raw=1 is in my extension's chrome folder as effective_tld_names.dat To run the code: authority = 'orkut.com.br'; lines = sc_geteffectivetldnames(); lines = sc_preparetouse(lines); domainname = sc_extractdomainname(authority, lines); The code: function sc_geteffectivetldnames () { var MY_ID = "[email protected]"; var em = Components.classes["@mozilla.org/extensions/manager;1"]. getService(Components.interfaces.nsIExtensionManager); var file = em.getInstallLocation(MY_ID).getItemFile(MY_ID, "chrome/effective_tld_names.dat"); var istream = Components.classes["@mozilla.org/network/file-input-stream;1"]. createInstance(Components.interfaces.nsIFileInputStream); istream.init(file, 0x01, 0444, 0); istream.QueryInterface(Components.interfaces.nsILineInputStream); var line = {}, lines = [], hasmore; do { hasmore = istream.readLine(line); lines.push(line.value); } while(hasmore); istream.close(); return lines; } function sc_preparetouse(lines) { lines = sc_notcomment(lines); lines = sc_notempty(lines); return lines; } function sc_notcomment(lines) { var line; var commentre; var matchedcomment; var replacedlines; replacedlines = new Array(); var i = 0; while (i < lines.length) { line = lines[i]; commentre = new RegExp("^//", 'i'); matchedcomment = line.match(commentre); if(matchedcomment) { lines.splice(i, 1); } else { i++; } } return lines; } function sc_notempty(lines) { var line; var emptyre; var matchedempty; var replacedlines; replacedlines = new Array(); var i = 0; while (i < lines.length) { line = lines[i]; emptyre = new RegExp("^$", 'i'); matchedempty = line.match(emptyre); if(matchedempty) { lines.splice(i, 1); } else { i++; } } return lines; } function sc_extractdomainname(authority, lines) { for (var i = 0; i < lines.length; i++) { line = lines[i]; alert(line); alert(typeof(line)); if (line.chatAt(0) == '*') { alert('test1'); continue; } if (line.chatAt(0) == '!') { alert('test2'); line.chatAt(0) = ''; } alert('test3'); checkline = sc_checknotasteriskline(authority, line); if (checkline) { domainname = checkline; } } if (!domainname) { for (var i = 0; i < lines.length; i++) { line = lines[i]; alert(line); if (line.chatAt(0) != '*') { continue; alert('test4'); } if (line.chatAt(0) == '!') { line.chatAt(0) = ''; alert('test5'); } alert('test6'); checkline = sc_checkasteriskline(authority, line); if (checkline) { domainname = checkline; } } } return domainname; } It alerts 'ac', then 'string', then nothing.

Read the article

alert(line) alerts 'ac' and typeof(line) is 'string', but charAt is not a function

- by Delirium tremens

alert(line) alerts 'ac' typeof(line) is 'string' When I run line.charAt(0), charAt is not a function. When line is 'http://www.google.com/', it works, I think it's the UTF-8 encoding of the file that I opened... How to make charAt work with UTF-8? UPDATED: http://mxr.mozilla.org/mozilla-central/source/netwerk/dns/src/effective_tld_names.dat?raw=1 is in my extension's chrome folder as effective_tld_names.dat To run the code: authority = 'orkut.com.br'; lines = sc_geteffectivetldnames(); lines = sc_preparetouse(lines); domainname = sc_extractdomainname(authority, lines); The code: function sc_geteffectivetldnames () { var MY_ID = "[email protected]"; var em = Components.classes["@mozilla.org/extensions/manager;1"]. getService(Components.interfaces.nsIExtensionManager); var file = em.getInstallLocation(MY_ID).getItemFile(MY_ID, "chrome/effective_tld_names.dat"); var istream = Components.classes["@mozilla.org/network/file-input-stream;1"]. createInstance(Components.interfaces.nsIFileInputStream); istream.init(file, 0x01, 0444, 0); istream.QueryInterface(Components.interfaces.nsILineInputStream); var line = {}, lines = [], hasmore; do { hasmore = istream.readLine(line); lines.push(line.value); } while(hasmore); istream.close(); return lines; } function sc_preparetouse(lines) { lines = sc_notcomment(lines); lines = sc_notempty(lines); return lines; } function sc_notcomment(lines) { var line; var commentre; var matchedcomment; var replacedlines; replacedlines = new Array(); var i = 0; while (i < lines.length) { line = lines[i]; commentre = new RegExp("^//", 'i'); matchedcomment = line.match(commentre); if(matchedcomment) { lines.splice(i, 1); } else { i++; } } return lines; } function sc_notempty(lines) { var line; var emptyre; var matchedempty; var replacedlines; replacedlines = new Array(); var i = 0; while (i < lines.length) { line = lines[i]; emptyre = new RegExp("^$", 'i'); matchedempty = line.match(emptyre); if(matchedempty) { lines.splice(i, 1); } else { i++; } } return lines; } function sc_extractdomainname(authority, lines) { for (var i = 0; i < lines.length; i++) { line = lines[i]; alert(line); alert(typeof(line)); if (line.chatAt(0) == '*') { alert('test1'); continue; } if (line.chatAt(0) == '!') { alert('test2'); line.chatAt(0) = ''; } alert('test3'); checkline = sc_checknotasteriskline(authority, line); if (checkline) { domainname = checkline; } } if (!domainname) { for (var i = 0; i < lines.length; i++) { line = lines[i]; alert(line); if (line.chatAt(0) != '*') { alert('test4'); continue; } if (line.chatAt(0) == '!') { alert('test5'); line.chatAt(0) = ''; } alert('test6'); checkline = sc_checkasteriskline(authority, line); if (checkline) { domainname = checkline; } } } return domainname; } It alerts 'ac', then 'string', then nothing.

Read the article

Using MS Standalone profiler in VS2008 Professional

- by fishdump

I am trying to profile my .NET dll while running it from VS unit testing tools but I am having problems. I am using the standalone command-line profiler as VS2008 Professional does not come with an inbuilt profiler. I have an open CMD window and have run the following commands (I instrumented it earlier which is why vsinstr gave the warning that it did): C:\...\BusinessRules\obj\Debug>vsperfclrenv /samplegclife /tracegclife /globalsamplegclife /globaltracegclife Enabling VSPerf Sampling Attach Profiling. Allows to 'attaching' to managed applications. Current Profiling Environment variables are: COR_ENABLE_PROFILING=1 COR_PROFILER={0a56a683-003a-41a1-a0ac-0f94c4913c48} COR_LINE_PROFILING=1 COR_GC_PROFILING=2 C:\...\BusinessRules\obj\Debug>vsinstr BusinessRules.dll Microsoft (R) VSInstr Post-Link Instrumentation 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. Error VSP1018 : VSInstr does not support processing binaries that are already instrumented. C:\...\BusinessRules\obj\Debug>vsperfcmd /start:trace /output:foo.vsp Microsoft (R) VSPerf Command Version 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. C:\...\BusinessRules\obj\Debug> I then ran the unit tests that exercised the instrumented code. When the unit tests were complete, I did... C:\...\BusinessRules\obj\Debug>vsperfcmd /shutdown Microsoft (R) VSPerf Command Version 9.0.30729 x86 Copyright (C) Microsoft Corp. All rights reserved. Waiting for process 4836 ( C:\Program Files\Microsoft Visual Studio 9.0\Common7\IDE\vstesthost.exe) to shutdown... It was clearly waiting for VS2008 to close so I closed it... Shutting down the Profile Monitor ------------------------------------------------------------ C:\...\BusinessRules\obj\Debug> All looking good, there was a 3.2mb foo.vsp file in the directory. I next did... C:\...\BusinessRules\obj\Debug>vsperfreport foo.vsp /summary:all Microsoft (R) VSPerf Report Generator, Version 9.0.0.0 Copyright (C) Microsoft Corporation. All rights reserved. VSP2340: Environment variables were not properly set during profiling run and managed symbols may not resolve. Please use vsperfclrenv before profiling. File opened Successfully opened the file. A report file, foo_Header.csv, has been generated. A report file, foo_MarksSummary.csv, has been generated. A report file, foo_ProcessSummary.csv, has been generated. A report file, foo_ThreadSummary.csv, has been generated. Analysis completed A report file, foo_FunctionSummary.csv, has been generated. A report file, foo_CallerCalleeSummary.csv, has been generated. A report file, foo_CallTreeSummary.csv, has been generated. A report file, foo_ModuleSummary.csv, has been generated. C:\...\BusinessRules\obj\Debug> Notice the warning about environment variables and using vsperfclrenv? But I had run it! Maybe I used the wrong switches? I don't know. Anyway, loading the csv files into Excel or using the perfconsole tool gives loads of useful info with useless symbol names: *** Loading commands from: C:\temp\PerfConsole\bin\commands\timebytype.dll *** Adding command: timebytype *** Loading commands from: C:\temp\PerfConsole\bin\commands\partition.dll *** Adding command: partition Welcome to PerfConsole 1.0 (for bugs please email: [email protected]), for help type: ?, for a quickstart type: ?? > load foo.vsp *** Couldn't match to either expected sampled or instrumented profile schema, defaulting to sampled *** Couldn't match to either expected sampled or instrumented profile schema, defaulting to sampled *** Profile loaded from 'foo.vsp' into @foo > > functions @foo >>>>> Function Name Exclusive Inclusive Function Name Module Name -------------------- -------------------- -------------- --------------- 900,798,600,000.00 % 900,798,600,000.00 % 0x0600003F 20397910 14,968,500,000.00 % 44,691,540,000.00 % 0x06000040 14736385 8,101,253,000.00 % 14,836,330,000.00 % 0x06000041 5491345 3,216,315,000.00 % 6,876,929,000.00 % 0x06000042 3924533 <snip> 71,449,430.00 % 71,449,430.00 % 0x0A000074 42572 52,914,200.00 % 52,914,200.00 % 0x0A000073 0 14,791.00 % 13,006,010.00 % 0x0A00007B 0 199,177.00 % 6,082,932.00 % 0x2B000001 5350072 2,420,116.00 % 2,420,116.00 % 0x0A00008A 0 836.00 % 451,888.00 % 0x0A000045 0 9,616.00 % 399,436.00 % 0x0A000039 0 18,202.00 % 298,223.00 % 0x06000046 1479900 I am so close to being able to find the bottlenecks, if only it will give me the function and module names instead of hex numbers! What am I doing wrong? --- Alistair.

Read the article

How does this decorator make a call to the 'register' method?

- by BryanWheelock

I'm trying to understand what is going on in the decorator @not_authenticated. The next step in the TraceRoute is to the method 'register' which is also located in django_authopenid/views.py which I just don't understand because I don't see anywhere that register is even mentioned in signin() How is the method 'register' called? def not_authenticated(func): """ decorator that redirect user to next page if he is already logged.""" def decorated(request, *args, **kwargs): if request.user.is_authenticated(): next = request.GET.get("next", "/") return HttpResponseRedirect(next) return func(request, *args, **kwargs) return decorated @not_authenticated def signin(request,newquestion=False,newanswer=False): """ signin page. It manage the legacy authentification (user/password) and authentification with openid. url: /signin/ template : authopenid/signin.htm """ request.encoding = 'UTF-8' on_failure = signin_failure next = clean_next(request.GET.get('next')) form_signin = OpenidSigninForm(initial={'next':next}) form_auth = OpenidAuthForm(initial={'next':next}) if request.POST: if 'bsignin' in request.POST.keys() or 'openid_username' in request.POST.keys(): form_signin = OpenidSigninForm(request.POST) if form_signin.is_valid(): next = clean_next(form_signin.cleaned_data.get('next')) sreg_req = sreg.SRegRequest(optional=['nickname', 'email']) redirect_to = "%s%s?%s" % ( get_url_host(request), reverse('user_complete_signin'), urllib.urlencode({'next':next}) ) return ask_openid(request, form_signin.cleaned_data['openid_url'], redirect_to, on_failure=signin_failure, sreg_request=sreg_req) elif 'blogin' in request.POST.keys(): # perform normal django authentification form_auth = OpenidAuthForm(request.POST) if form_auth.is_valid(): user_ = form_auth.get_user() login(request, user_) next = clean_next(form_auth.cleaned_data.get('next')) return HttpResponseRedirect(next) question = None if newquestion == True: from forum.models import AnonymousQuestion as AQ session_key = request.session.session_key qlist = AQ.objects.filter(session_key=session_key).order_by('-added_at') if len(qlist) > 0: question = qlist[0] answer = None if newanswer == True: from forum.models import AnonymousAnswer as AA session_key = request.session.session_key alist = AA.objects.filter(session_key=session_key).order_by('-added_at') if len(alist) > 0: answer = alist[0] return render('authopenid/signin.html', { 'question':question, 'answer':answer, 'form1': form_auth, 'form2': form_signin, 'msg': request.GET.get('msg',''), 'sendpw_url': reverse('user_sendpw'), }, context_instance=RequestContext(request)) Looking at the request, it seems that account/register/ does reference the register method with 'PATH_INFO': u'/account/register/' Here is the request: <WSGIRequest GET:<QueryDict: {}>, POST:<QueryDict: {u'username': [u'BryanWheelock'], u'email': [u'[email protected]'], u'bnewaccount': [u'Signup']}>, COOKIES:{'__utma': '127460431.1218630960.1266769637.1266769637.1266864494.2', '__utmb': '127460431.3.10.1266864494', '__utmc': '127460431', '__utmz': '127460431.1266769637.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none)', 'sessionid': 'fb15ee538320170a22d3a3a324aad968'}, META:{'CONTENT_LENGTH': '74', 'CONTENT_TYPE': 'application/x-www-form-urlencoded', 'DOCUMENT_ROOT': '/usr/local/apache2/htdocs', 'GATEWAY_INTERFACE': 'CGI/1.1', 'HTTP_ACCEPT': 'application/xml,application/xhtml+xml,text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5', 'HTTP_ACCEPT_CHARSET': 'ISO-8859-1,utf-8;q=0.7,*;q=0.3', 'HTTP_ACCEPT_ENCODING': 'gzip,deflate,sdch', 'HTTP_ACCEPT_LANGUAGE': 'en-US,en;q=0.8', 'HTTP_CACHE_CONTROL': 'max-age=0', 'HTTP_CONNECTION': 'close', 'HTTP_COOKIE': '__utmz=127460431.1266769637.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); __utma=127460431.1218630960.1266769637.1266769637.1266864494.2; __utmc=127460431; __utmb=127460431.3.10.1266864494; sessionid=fb15ee538320170a22d3a3a324aad968', 'HTTP_HOST': 'workproject.com', 'HTTP_ORIGIN': 'http://workproject.com', 'HTTP_REFERER': 'http://workproject.com/account/signin/complete/?next=%2F&janrain_nonce=2010-02-22T18%3A49%3A53ZG2KXci&openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=id_res&openid.op_endpoint=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fud&openid.response_nonce=2010-02-22T18%3A49%3A53Znxxxxxxxxxw&openid.return_to=http%3A%2F%2Fworkproject.com%2Faccount%2Fsignin%2Fcomplete%2F%3Fnext%3D%252F%26janrain_nonce%3D2010-02-22T18%253A49%253A53ZG2KXci&openid.assoc_handle=AOQobUepU4xs-kGg5LiyLzfN3RYv0I0Jocgjf_1odT4RR9zfMFpQVpMg&openid.signed=op_endpoint%2Cclaimed_id%2Cidentity%2Creturn_to%2Cresponse_nonce%2Cassoc_handle&openid.sig=Jf76i2RNhqpLTJMjeQ0nnQz6fgA%3D&openid.identity=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fid%3Fid%3DAItxxxxxxxxxs9CxHQ3PrHw_N5_3j1HM&openid.claimed_id=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fid%3Fid%3DAItOaxxxxxxxxxxx4s9CxHQ3PrHw_N5_3j1HM', 'HTTP_USER_AGENT': 'Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10_5_8; en-US) AppleWebKit/532.9 (KHTML, like Gecko) Chrome/5.0.307.7 Safari/532.9', 'HTTP_X_FORWARDED_FOR': '96.8.31.235', 'PATH': '/usr/bin:/bin', 'PATH_INFO': u'/account/register/', 'PATH_TRANSLATED': '/home/spirituality/webapps/work/spirit_app.wsgi/account/register/', 'QUERY_STRING': '', 'REMOTE_ADDR': '127.0.0.1', 'REMOTE_PORT': '59956', 'REQUEST_METHOD': 'POST', 'REQUEST_URI': '/account/register/', 'SCRIPT_FILENAME': '/home/spirituality/webapps/spirituality/spirit_app.wsgi', 'SCRIPT_NAME': u'', 'SERVER_ADDR': '127.0.0.1', 'SERVER_ADMIN': '[no address given]', 'SERVER_NAME': 'workproject.com', 'SERVER_PORT': '80', 'SERVER_PROTOCOL': 'HTTP/1.0', 'SERVER_SIGNATURE': '', 'SERVER_SOFTWARE': 'Apache/2.2.12 (Unix) mod_wsgi/2.5 Python/2.5.4', 'mod_wsgi.application_group': 'www.workProject.com|', 'mod_wsgi.callable_object': 'application', 'mod_wsgi.listener_host': '', 'mod_wsgi.listener_port': '25931', 'mod_wsgi.process_group': '', 'mod_wsgi.reload_mechanism': '0', 'mod_wsgi.script_reloading': '1', 'mod_wsgi.version': (2, 5), 'wsgi.errors': <mod_wsgi.Log object at 0xb7ce0038>, 'wsgi.file_wrapper': <built-in method file_wrapper of mod_wsgi.Adapter object at 0xb7e94b18>, 'wsgi.input': <mod_wsgi.Input object at 0x999cc78>, 'wsgi.multiprocess': True, 'wsgi.multithread': False, 'wsgi.run_once': False, 'wsgi.url_scheme': 'http', 'wsgi.version': (1, 0)}>

Read the article

WPF DataGrid does not scoll on drag

- by Greg R

I have a strange problem with a WPF DataGrid from WPF Toolkit. The scrollbars appear correctly when the number of rows grows, and the scrolling works when you press up or down arrows on the scrollbar. The problem comes in when I try to drag the scrollbar on the datagrid. My page has a scroll viewer around it. When I click and drag the scrollbar on the grid, it scrolls the page scroller instead. If the scrollbar does not apear on the page, there grid still does not scroll. Is there a workaround for this??? Would really appreciate some help with this issue! For example, in this case if the page is < 280, it scrolls on drag. But drag scrolling does not work on the grid. <ScrollViewer ScrollViewer.IsDeferredScrollingEnabled="True" HorizontalScrollBarVisibility="Auto" VerticalScrollBarVisibility="Auto" > <DockPanel> <dg:DataGrid HorizontalScrollBarVisibility="Auto" SelectionMode="Single" CanUserAddRows="False" CanUserDeleteRows="False" CanUserResizeColumns="False" CanUserSortColumns="False" AutoGenerateColumns="False" RowHeaderWidth="17" ItemsSource="{Binding Path=OrderSearchVm}" IsReadOnly="True" MaxHeight="280" DockPanel.Dock="Top"> <dg:DataGrid.Columns> <dg:DataGridTextColumn Width="75" Header="Date" Binding="{Binding Path=OrderDate}" > <dg:DataGridTextColumn.ElementStyle> <Style TargetType="{x:Type TextBlock}"> <Setter Property="TextWrapping" Value="Wrap" /> </Style> </dg:DataGridTextColumn.ElementStyle> </dg:DataGridTextColumn> <dg:DataGridTextColumn Header="Type" Binding="{Binding Path=OrderType}" Width="45"/> <dg:DataGridTextColumn Header="Shipping Name" Binding="{Binding Path=ShipToName}" Width="115"> <dg:DataGridTextColumn.ElementStyle> <Style TargetType="{x:Type TextBlock}"> <Setter Property="TextWrapping" Value="Wrap" /> </Style> </dg:DataGridTextColumn.ElementStyle> </dg:DataGridTextColumn> <dg:DataGridTextColumn Header="Shipping Address " Binding="{Binding Path=ShipToAddress}" Width="160"> <dg:DataGridTextColumn.ElementStyle> <Style TargetType="{x:Type TextBlock}"> <Setter Property="TextWrapping" Value="Wrap" /> </Style> </dg:DataGridTextColumn.ElementStyle> </dg:DataGridTextColumn> <dg:DataGridTextColumn Header="E-Mail" Binding="{Binding Path=Email}" Width="140"> <dg:DataGridTextColumn.ElementStyle> <Style TargetType="{x:Type TextBlock}"> <Setter Property="TextWrapping" Value="Wrap" /> </Style> </dg:DataGridTextColumn.ElementStyle> </dg:DataGridTextColumn> </dg:DataGrid.Columns> </dg:DataGrid> </DockPanel> </ScrollViewer>

Read the article

FBML is not rendered in Facebook App in iframe - please help

- by Jakob

I'm developing an Facebook Application in PHP. It's loaded as an iframe and not as FBML. The normal interaction with Facebook works. For example the following code gives the username: $facebook = new Facebook($config->appapikey, $config->appsecret); $user_id = $facebook->require_login($required_permissions = 'email'); echo $user->name; Where $user is my class in which the user-details are loaded from facebook. My document begins the following way: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xmlns:fb="http://www.facebook.com/2008/fbml"> <head><title>Appname</title> </head> <body> <script src="http://static.ak.connect.facebook.com/js/api_lib/v0.4/FeatureLoader.js.php/de_DE" type="text/javascript"></script> And ends likes this: <script type="text/javascript"> FB_RequireFeatures(['XFBML','CanvasUtil'], function(){ FB.init("<?php echo $config->appapikey; ?>", "/app/xd_receiver.htm"); FB.CanvasClient.startTimerToSizeToContent(); }); </script> </body> </html> Also the file xd_receiver.htm is loaded as I can see in Firebug. But my problem is that for example the request-form is not loaded. My code: <fb:serverFbml> <script type="text/fbml"> <fb:fbml> <fb:request-form method="post" action="<?php echo $config->site; ?>index.php" type="appname" invite="true" target="_top" content="content"> <fb:multi-friend-selector actiontext="text" rows="3" showborder="true" target="_top"/> </fb:request-form> </fb:fbml> </script> </fb:serverFbml> I can see the code with Firebug but the form ist not displayed by Facebook. 2 or 3 weeks ago it was displayed but in this time I had the tags </fb:fbml> </script> </fb:serverFbml> arround my complete text in the body. 2 weeks ago I had the the problem that nothing any more was displayed. After I removed the tags my app is displayed but not the form. I am searchign the web vor 1 week now and read many Threads about FBML and XFBML in Facebook but nothing worked for me. So thank you in advance for help.

Read the article

GAE formpreview

- by Niklas R

I'm trying to enable form preview with Google App Engine. Getting the following error message I suspect being mistaken somewhere: ... handler = handler_class() TypeError: __call__() takes at least 2 arguments (1 given) Can you tell what's wrong with my attempt? Here is some of the code. from django.contrib.formtools.preview import FormPreview class AFormPreview(FormPreview): def done(self, request, cleaned_data): # Do something with the cleaned_data, then redirect # to a "success" page. self.response.out.write('Done!') class AForm(djangoforms.ModelForm): text = forms.CharField(widget=forms.Textarea(attrs={'rows':'11','cols':'70','class':'foo'}),label=_("content").capitalize()) def clean(self): cleaned_data = self.clean_data name = cleaned_data.get("name") if not name: raise forms.ValidationError("No name.") # Always return the full collection of cleaned data. return cleaned_data class Meta: model = A fields = ['category','currency','price','title','phonenumber','postaladress','name','text','email'] #change the order ... ('/aformpreview/([^/]*)', AFormPreview(AForm)), UPDATE: Here's a complete app where the preview is not working. Any ideas are most welcome: import cgi from google.appengine.api import users from google.appengine.ext import db from google.appengine.ext import webapp from google.appengine.ext.webapp import template from google.appengine.ext.webapp.util import run_wsgi_app from google.appengine.ext.db import djangoforms class Item(db.Model): name = db.StringProperty() quantity = db.IntegerProperty(default=1) target_price = db.FloatProperty() priority = db.StringProperty(default='Medium',choices=[ 'High', 'Medium', 'Low']) entry_time = db.DateTimeProperty(auto_now_add=True) added_by = db.UserProperty() class ItemForm(djangoforms.ModelForm): class Meta: model = Item exclude = ['added_by'] from django.contrib.formtools.preview import FormPreview class ItemFormPreview(FormPreview): def done(self, request, cleaned_data): # Do something with the cleaned_data, then redirect # to a "success" page. return HttpResponseRedirect('/') class MainPage(webapp.RequestHandler): def get(self): self.response.out.write('<html><body>' '<form method="POST" ' 'action="/">' '<table>') # This generates our shopping list form and writes it in the response self.response.out.write(ItemForm()) self.response.out.write('</table>' '<input type="submit">' '</form></body></html>') def post(self): data = ItemForm(data=self.request.POST) if data.is_valid(): # Save the data, and redirect to the view page entity = data.save(commit=False) entity.added_by = users.get_current_user() entity.put() self.redirect('/items.html') else: # Reprint the form self.response.out.write('<html><body>' '<form method="POST" ' 'action="/">' '<table>') self.response.out.write(data) self.response.out.write('</table>' '<input type="submit">' '</form></body></html>') class ItemPage(webapp.RequestHandler): def get(self): query = db.GqlQuery("SELECT * FROM Item ORDER BY name") for item in query: self.response.out.write('<a href="/edit?id=%d">Edit</a> - ' % item.key().id()) self.response.out.write("%s - Need to buy %d, cost $%0.2f each<br>" % (item.name, item.quantity, item.target_price)) class EditPage(webapp.RequestHandler): def get(self): id = int(self.request.get('id')) item = Item.get(db.Key.from_path('Item', id)) self.response.out.write('<html><body>' '<form method="POST" ' 'action="/edit">' '<table>') self.response.out.write(ItemForm(instance=item)) self.response.out.write('</table>' '<input type="hidden" name="_id" value="%s">' '<input type="submit">' '</form></body></html>' % id) def post(self): id = int(self.request.get('_id')) item = Item.get(db.Key.from_path('Item', id)) data = ItemForm(data=self.request.POST, instance=item) if data.is_valid(): # Save the data, and redirect to the view page entity = data.save(commit=False) entity.added_by = users.get_current_user() entity.put() self.redirect('/items.html') else: # Reprint the form self.response.out.write('<html><body>' '<form method="POST" ' 'action="/edit">' '<table>') self.response.out.write(data) self.response.out.write('</table>' '<input type="hidden" name="_id" value="%s">' '<input type="submit">' '</form></body></html>' % id) def main(): application = webapp.WSGIApplication( [('/', MainPage), ('/edit', EditPage), ('/items.html', ItemPage), ('/itemformpreview', ItemFormPreview(ItemForm)), ], debug=True) run_wsgi_app(application)

Read the article

handle null values for string when implementing IXmlSerializable interface

- by user208081

I have the following class that implements IXmlSerializable. When implementing WriteXml(), I need to handle the case where the string members of this class may be null values. What is the best way of handling this? Currently, I am using the default constructor in which all the string properties are initialized to empty string values. This way, when WriteXml() is called, the string will not be null. One other way I could do this is check using String.IsNullOrEmpty before writing each string in xml. Any suggestions on how I can improve this code? using System; using System.Collections.Generic; using System.Linq; using System.Text; using System.Xml.Serialization; using System.Globalization; namespace TCS.Common.InformationObjects { public sealed class FaxSender : IXmlSerializable { #region Public Constants private const string DEFAULT_CLASS_NAME = "FaxSender"; #endregion Public Constants #region Public Properties public string Name { get; set; } public string Organization { get; set; } public string PhoneNumber { get; set; } public string FaxNumber { get; set; } public string EmailAddress { get; set; } #endregion Public Properties #region Public Methods #region Constructors public FaxSender() { Name = String.Empty; Organization = String.Empty; PhoneNumber = String.Empty; FaxNumber = String.Empty; EmailAddress = String.Empty; } public FaxSender(string name, string organization, string phoneNumber, string faxNumber, string emailAddress) { Name = name; Organization = organization; PhoneNumber = phoneNumber; FaxNumber = faxNumber; EmailAddress = emailAddress; } #endregion Constructors #region IXmlSerializable Members public System.Xml.Schema.XmlSchema GetSchema() { throw new NotImplementedException(); } public void ReadXml(System.Xml.XmlReader reader) { throw new NotImplementedException(); } public void WriteXml(System.Xml.XmlWriter xmlWriter) { try { // <sender> xmlWriter.WriteStartElement("sender"); // Write the name of the sender as an element. xmlWriter.WriteElementString("name", this.Name.ToString(CultureInfo.CurrentCulture)); // Write the organization of the sender as an element. xmlWriter.WriteElementString("organization", this.Organization.ToString(CultureInfo.CurrentCulture)); // Write the phone number of the sender as an element. xmlWriter.WriteElementString("phone_number", this.PhoneNumber.ToString(CultureInfo.CurrentCulture)); // Write the fax number of the sender as an element. xmlWriter.WriteElementString("fax_number", this.FaxNumber.ToString(CultureInfo.CurrentCulture)); // Write the email address of the sender as an element. xmlWriter.WriteElementString("email_address", this.EmailAddress.ToString(CultureInfo.CurrentCulture)); // </sender> xmlWriter.WriteEndElement(); } catch { // Rethrow any exceptions. throw; } } #endregion IXmlSerializable Members #endregion Public Methods } }

Read the article

Autocomplete jQuery on User Controller within Repeater .NET

- by TheDPQ

I have a Multiview search feature on a Web User Controller that is called within a Repeater, OHMY!! I have some training sessions being listed out on a page, each calling an employeeSearch Web User Controller so people can search for employees to add to the training session. I have the Employee Names and Employee IDs listed out in JS on the page and using the jQuery autocomplete i have them search for the employee and populate a hidden field in the User controller. Once the process is done they have the option of adding yet another employee. So i had Autocompelte 'work' in all the employee search boxes, but one i do the initial search (postback) autocomplete won't work again. Then i updated $().ready(function() to pageLoad() so it works correctly on multiple searches but only in the LAST item of the repeater (jQuery is loaded on the User Controller) FYI: I have the JS string set as EMPLOYEENAME|ID and jQuery displays the Employee Name and if they select it throws the ID in a ASP:HIDDEN FIELD <script type="text/javascript"> format_item = function(item, position, length) { var str = item.toString().split("|", 2); return str[0]; } function pageLoad() { $("#<%=tb_EmployeeName.ClientID %>").autocomplete(EmployeeList, { minChars: 0, width: 500, matchContains: true, autoFill: false, scrollHeight: 300, scroll: true, formatItem: format_item, formatMatch: format_item, formatResult: format_item }); $("#<%=tb_EmployeeName.ClientID %>").result(function(event, data, formatted) { var str = data.toString().split("|", 2); $("#<%=hf_EmployeeID.ClientID %>").val(str[1]); }); }; </script> I can already guess that by repeating pageLoad within the User Controll i override the previous pageLoad. THE QUESTION: Is there a way around this, a way to have all the jQuery appear in a single pageLoad or to somehow have a single jquery call to handle all my search boxes? I can't move the jQuery into the page calling all the controllers because i have no way of referencing the specific *tb_EmployeeName* textbox AND *hf_EmployeeID* hidden field. Thank you so much for any help or insight you can give me into this problem. This is the Multiview that on the User Controller <asp:MultiView ID="mv_EmployeeArea" runat="server" ActiveViewIndex="0"> <asp:View ID="vw_Search" runat="server"> <asp:Panel ID="eSearch" runat="server"> <b>Signup Employee Search</b> (<i>Last Name, First Name</i>)<br /> <asp:TextBox ID="tb_EmployeeName" class="EmployeeSearch" runat="server"></asp:TextBox> <asp:HiddenField ID="hf_EmployeeID" runat="server" /> <asp:Button ID="btn_Search" runat="server" Text="Search" /> </asp:Panel> </asp:View> <asp:View ID="vw_Confirm" runat="server"> <b>Signup Confirmation</b> <asp:FormView ID="fv_EmployeeInfo" runat="server"> <ItemTemplate> <%#(Eval("LastName"))%>, <%#(Eval("FirstName"))%><br /> </ItemTemplate> </asp:FormView> <asp:Button ID="btn_Confirm" runat="server" Text="Signup this employee" />   <asp:Button ID="btn_Reset3" runat="server" Text="Reset" /> </asp:View> <asp:View ID="vw_ThankYou" runat="server"> <b>Thank You</b><br /> The employee has been signed up and an email confirmation has been sent out.<br /><br /> <asp:Button ID="btn_Reset" runat="server" Text="Reset" /> </asp:View> </asp:MultiView> UPDATE: I never did find an answer but i had to do a demo so i hacked together something that 'works', but feels sort of cheesy. I am still very much needed of a better question or better understanding.

Read the article

Persistance JDO - How to query a property of a collection with JDOQL?

- by Sergio del Amo

I want to build an application where a user identified by an email address can have several application accounts. Each account can have one o more users. I am trying to use the JDO Storage capabilities with Google App Engine Java. Here is my attempt: @PersistenceCapable @Inheritance(strategy = InheritanceStrategy.NEW_TABLE) public class AppAccount { @PrimaryKey @Persistent(valueStrategy = IdGeneratorStrategy.IDENTITY) private Long id; @Persistent private String companyName; @Persistent List<Invoices> invoices = new ArrayList<Invoices>(); @Persistent List<AppUser> users = new ArrayList<AppUser>(); // Getter Setters and Other Fields } @PersistenceCapable @EmbeddedOnly public class AppUser { @Persistent private String username; @Persistent private String firstName; @Persistent private String lastName; // Getter Setters and Other Fields } When a user logs in, I want to check how many accounts does he belongs to. If he belongs to more than one he will be presented with a dashboard where he can click which account he wants to load. This is my code to retrieve a list of app accounts where he is registered. public static List<AppAccount> getUserAppAccounts(String username) { PersistenceManager pm = JdoUtil.getPm(); Query q = pm.newQuery(AppAccount.class); q.setFilter("users.username == usernameParam"); q.declareParameters("String usernameParam"); return (List<AppAccount>) q.execute(username); } But I get the next error: SELECT FROM invoices.server.AppAccount WHERE users.username == usernameParam PARAMETERS String usernameParam: Encountered a variable expression that isn't part of a join. Maybe you're referencing a non-existent field of an embedded class. org.datanucleus.store.appengine.FatalNucleusUserException: SELECT FROM com.softamo.pelicamo.invoices.server.AppAccount WHERE users.username == usernameParam PARAMETERS String usernameParam: Encountered a variable expression that isn't part of a join. Maybe you're referencing a non-existent field of an embedded class. at org.datanucleus.store.appengine.query.DatastoreQuery.getJoinClassMetaData(DatastoreQuery.java:1154) at org.datanucleus.store.appengine.query.DatastoreQuery.addLeftPrimaryExpression(DatastoreQuery.java:1066) at org.datanucleus.store.appengine.query.DatastoreQuery.addExpression(DatastoreQuery.java:846) at org.datanucleus.store.appengine.query.DatastoreQuery.addFilters(DatastoreQuery.java:807) at org.datanucleus.store.appengine.query.DatastoreQuery.performExecute(DatastoreQuery.java:226) at org.datanucleus.store.appengine.query.JDOQLQuery.performExecute(JDOQLQuery.java:85) at org.datanucleus.store.query.Query.executeQuery(Query.java:1489) at org.datanucleus.store.query.Query.executeWithArray(Query.java:1371) at org.datanucleus.jdo.JDOQuery.execute(JDOQuery.java:243) at com.softamo.pelicamo.invoices.server.Store.getUserAppAccounts(Store.java:82) at com.softamo.pelicamo.invoices.test.server.StoreTest.testgetUserAppAccounts(StoreTest.java:39) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.junit.runners.model.FrameworkMethod$1.runReflectiveCall(FrameworkMethod.java:44) at org.junit.internal.runners.model.ReflectiveCallable.run(ReflectiveCallable.java:15) at org.junit.runners.model.FrameworkMethod.invokeExplosively(FrameworkMethod.java:41) at org.junit.internal.runners.statements.InvokeMethod.evaluate(InvokeMethod.java:20) at org.junit.internal.runners.statements.RunBefores.evaluate(RunBefores.java:28) at org.junit.internal.runners.statements.RunAfters.evaluate(RunAfters.java:31) at org.junit.runners.BlockJUnit4ClassRunner.runChild(BlockJUnit4ClassRunner.java:76) at org.junit.runners.BlockJUnit4ClassRunner.runChild(BlockJUnit4ClassRunner.java:50) at org.junit.runners.ParentRunner$3.run(ParentRunner.java:193) at org.junit.runners.ParentRunner$1.schedule(ParentRunner.java:52) at org.junit.runners.ParentRunner.runChildren(ParentRunner.java:191) at org.junit.runners.ParentRunner.access$000(ParentRunner.java:42) at org.junit.runners.ParentRunner$2.evaluate(ParentRunner.java:184) at org.junit.runners.ParentRunner.run(ParentRunner.java:236) at org.eclipse.jdt.internal.junit4.runner.JUnit4TestReference.run(JUnit4TestReference.java:46) at org.eclipse.jdt.internal.junit.runner.TestExecution.run(TestExecution.java:38) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:467) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:683) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:390) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:197) Any idea? I am getting JDO persistance totally wrong?

Search Results

Search found 10793 results on 432 pages for 'plaintext email'.

Page 420/432 | < Previous Page | 416 417 418 419 420 421 422 423 424 425 426 427 | Next Page >

- by 2020mobile

- by phew

- by user45611

- by Mohamed Elgharabawy

- by Pierre Jeptha

- by dbf

- by microchasm

- by matt74tm

- by DaveJohnston

- by Mike Wells

- by Chuck Herrington

- by klausch

- by David J.

- by SomFred

- by edu222

- by Delirium tremens

- by Delirium tremens

- by fishdump

- by BryanWheelock

- by Greg R

- by Jakob

- by Niklas R

- by user208081

- by TheDPQ

- by Sergio del Amo

< Previous Page | 416 417 418 419 420 421 422 423 424 425 426 427 | Next Page >