Search Results

Search found 10550 results on 422 pages for 'syntax rules'.

Page 420/422 | < Previous Page | 416 417 418 419 420 421 422  | Next Page >

• Inbound SIP calls through Cisco 881 NAT hang up after a few seconds

  - by MasterRoot24

  I've recently moved to a Cisco 881 router for my WAN link. I was previously using a Cisco Linksys WAG320N as my modem/router/WiFi AP/NAT firewall. The WAG320N is now running in bridged mode, so it's simply acting as a modem with one of it's LAN ports connected to FE4 WAN on my Cisco 881. The Cisco 881 get's a DHCP provided IP from my ISP. My LAN is part of default Vlan 1 (192.168.1.0/24). General internet connectivity is working great, I've managed to setup static NAT rules for my HTTP/HTTPS/SMTP/etc. services which are running on my LAN. I don't know whether it's worth mentioning that I've opted to use NVI NAT (ip nat enable as opposed to the traditional ip nat outside/ip nat inside) setup. My reason for this is that NVI allows NAT loopback from my LAN to the WAN IP and back in to the necessary server on the LAN. I run an Asterisk 1.8 PBX on my LAN, which connects to a SIP provider on the internet. Both inbound and outbound calls through the old setup (WAG320N providing routing/NAT) worked fine. However, since moving to the Cisco 881, inbound calls drop after around 10 seconds, whereas outbound calls work fine. The following message is logged on my Asterisk PBX: [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3641 retrans_pkt: Retransmission timeout reached on transmission [email protected] for seqno 1 (Critical Response) -- See https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions Packet timed out after 6528ms with no response [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3670 retrans_pkt: Hanging up call [email protected] - no reply to our critical packet (see https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions). (I know that this is quite a common issue - I've spend the best part of 2 days solid on this, trawling Google.) I've done as I am told and checked https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions. Referring to the section "Other SIP requests" in the page linked above, I believe that the hangup to be caused by the ACK from my SIP provider not being passed back through NAT to Asterisk on my PBX. I tried to ascertain this by dumping the packets on my WAN interface on the 881. I managed to obtain a PCAP dump of packets in/out of my WAN interface. Here's an example of an ACK being reveived by the router from my provider: 689 21.219999 193.x.x.x 188.x.x.x SIP 502 Request: ACK sip:[email protected] | However a SIP trace on the Asterisk server show's that there are no ACK's received in response to the 200 OK from my PBX: http://pastebin.com/wwHpLPPz In the past, I have been strongly advised to disable any sort of SIP ALGs on routers and/or firewalls and the many posts regarding this issue on the internet seem to support this. However, I believe on Cisco IOS, the config command to disable SIP ALG is no ip nat service sip udp port 5060 however, this doesn't appear to help the situation. To confirm that config setting is set: Router1#show running-config | include sip no ip nat service sip udp port 5060 Another interesting twist: for a short period of time, I tried another provider. Luckily, my trial account with them is still available, so I reverted my Asterisk config back to the revision before I integrated with my current provider. I then dialled in to the DDI associated with the trial trunk and the call didn't get hung up and I didn't get the error above! To me, this points at the provider, however I know, like all providers do, will say "There's no issues with our SIP proxies - it's your firewall." I'm tempted to agree with this, as this issue was not apparent with the old WAG320N router when it was doing the NAT'ing. I'm sure you'll want to see my running-config too: ! ! Last configuration change at 15:55:07 UTC Sun Dec 9 2012 by xxx version 15.2 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone no service password-encryption service sequence-numbers ! hostname Router1 ! boot-start-marker boot-end-marker ! ! security authentication failure rate 10 log security passwords min-length 6 logging buffered 4096 logging console critical enable secret 4 xxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 quit no ip source-route no ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! no ip bootp server ip domain name dmz.merlin.local ip domain list dmz.merlin.local ip domain list merlin.local ip name-server x.x.x.x ip inspect audit-trail ip inspect udp idle-time 1800 ip inspect dns-timeout 7 ip inspect tcp idle-time 14400 ip inspect name autosec_inspect ftp timeout 3600 ip inspect name autosec_inspect http timeout 3600 ip inspect name autosec_inspect rcmd timeout 3600 ip inspect name autosec_inspect realaudio timeout 3600 ip inspect name autosec_inspect smtp timeout 3600 ip inspect name autosec_inspect tftp timeout 30 ip inspect name autosec_inspect udp timeout 15 ip inspect name autosec_inspect tcp timeout 3600 ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn ! ! username xxx privilege 15 secret 4 xxx username xxx secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp no ip redirects no ip unreachables no ip proxy-arp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.2 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! no ip nat service sip udp port 5060 ip nat source list 1 interface FastEthernet4 overload ip nat source static tcp x.x.x.x 80 interface FastEthernet4 80 ip nat source static tcp x.x.x.x 443 interface FastEthernet4 443 ip nat source static tcp x.x.x.x 25 interface FastEthernet4 25 ip nat source static tcp x.x.x.x 587 interface FastEthernet4 587 ip nat source static tcp x.x.x.x 143 interface FastEthernet4 143 ip nat source static tcp x.x.x.x 993 interface FastEthernet4 993 ip nat source static tcp x.x.x.x 1723 interface FastEthernet4 1723 ! ! logging trap debugging logging facility local2 access-list 1 permit 192.168.1.0 0.0.0.255 access-list 1 permit 192.168.0.0 0.0.0.255 no cdp run ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 login authentication local_auth length 0 transport output all line aux 0 exec-timeout 15 0 login authentication local_auth transport output all line vty 0 1 access-class 1 in logging synchronous login authentication local_auth length 0 transport preferred none transport input telnet transport output all line vty 2 4 access-class 1 in login authentication local_auth length 0 transport input ssh transport output all ! ! end ...and, if it's of any use, here's my Asterisk SIP config: [general] context=default ; Default context for calls allowoverlap=no ; Disable overlap dialing support. (Default is yes) udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) tcpenable=no ; Enable server for incoming TCP connections (default is no) tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) srvlookup=yes ; Enable DNS SRV lookups on outbound calls ; Note: Asterisk only uses the first host ; in SRV records ; Disabling DNS SRV lookups disables the ; ability to place SIP calls based on domain ; names to some other SIP users on the Internet ; Specifying a port in a SIP peer definition or ; when dialing outbound calls will supress SRV ; lookups for that peer or call. directmedia=no ; Don't allow direct RTP media between extensions (doesn't work through NAT) externhost=<MY DYNDNS HOSTNAME> ; Our external hostname to resolve to IP and be used in NAT'ed packets localnet=192.168.1.0/24 ; Define our local network so we know which packets need NAT'ing qualify=yes ; Qualify peers by default dtmfmode=rfc2833 ; Set the default DTMF mode disallow=all ; Disallow all codecs by default allow=ulaw ; Allow G.711 u-law allow=alaw ; Allow G.711 a-law ; ---------------------- ; SIP Trunk Registration ; ---------------------- ; Orbtalk register => <MY SIP PROVIDER USER NAME>:[email protected]/<MY DDI> ; Main Orbtalk number ; ---------- ; Trunks ; ---------- [orbtalk] ; Main Orbtalk trunk type=peer insecure=invite host=sipgw3.orbtalk.co.uk nat=yes username=<MY SIP PROVIDER USER NAME> defaultuser=<MY SIP PROVIDER USER NAME> fromuser=<MY SIP PROVIDER USER NAME> secret=xxx context=inbound I really don't know where to go with this. If anyone can help me find out why these calls are being dropped off, I'd be grateful if you could chime in! Please let me know if any further info is required.

  Read the article

• Apache + Codeigniter + New Server + Unexpected Errors

  - by ngl5000

  Alright here is the situation: I use to have my codeigniter site at bluehost were I did not have root access, I have since moved that site to rackspace. I have not changed any of the PHP code yet there has been some unexpected behavior. Unexpected Behavior: http://mysite.com/robots.txt Both old and new resolve to the robots file http://mysite.com/robots.txt/ The old bluehost setup resolves to my codeigniter 404 error page. The rackspace config resolves to: Not Found The requested URL /robots.txt/ was not found on this server. **This instance leads me to believe that there could be a problem with my mod rewrites or lack there of. The first one produces the error correctly through php while it seems the second senario lets the server handle this error. The next instance of this problem is even more troubling: 'http://mysite.com/search/term/9 x 1-1%2F2 white/' New site results in: Bad Request Your browser sent a request that this server could not understand. Old site results in: The actual page being loaded and the search term being unencoded. I have to assume that this has something to do with the fact that when I went to the new server I went from root level htaccess file to httpd.conf file and virtual server default and default-ssl. Here they are: Default file: <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName mysite.com DocumentRoot /var/www <Directory /> Options +FollowSymLinks AllowOverride None </Directory> <Directory /var/www> Options -Indexes +FollowSymLinks -MultiViews AllowOverride None Order allow,deny allow from all RewriteEngine On RewriteBase / # force no www. (also does the IP thing) RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} !^mysite\.com [NC] RewriteRule ^(.*)$ http://mysite.com/$1 [R=301,L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.+)\.(\d+)\.(js|css|png|jpg|gif)$ $1.$3 [L] # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] # codeigniter direct RewriteCond $0 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^.*$ index.php [L] </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> Default-ssl File <IfModule mod_ssl.c> <VirtualHost _default_:443> ServerAdmin webmaster@localhost ServerName mysite.com DocumentRoot /var/www <Directory /> Options +FollowSymLinks AllowOverride None </Directory> <Directory /var/www> Options -Indexes +FollowSymLinks -MultiViews AllowOverride None Order allow,deny allow from all RewriteEngine On RewriteBase / RewriteCond %{SERVER_PORT} !^443 RewriteRule ^ https://mysite.com%{REQUEST_URI} [R=301,L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.+)\.(\d+)\.(js|css|png|jpg|gif)$ $1.$3 [L] # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] # codeigniter direct RewriteCond $0 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^.*$ index.php [L] </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/ssl_access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> # SSL Engine Switch: # Enable/Disable SSL for this virtual host. SSLEngine on # Use our self-signed certificate by default SSLCertificateFile /etc/apache2/ssl/certs/www.mysite.com.crt SSLCertificateKeyFile /etc/apache2/ssl/private/www.mysite.com.key # A self-signed (snakeoil) certificate can be created by installing # the ssl-cert package. See # /usr/share/doc/apache2.2-common/README.Debian.gz for more info. # If both key and certificate are stored in the same file, only the # SSLCertificateFile directive is needed. # SSLCertificateFile /etc/ssl/certs/ssl-cert-snakeoil.pem # SSLCertificateKeyFile /etc/ssl/private/ssl-cert-snakeoil.key # Server Certificate Chain: # Point SSLCertificateChainFile at a file containing the # concatenation of PEM encoded CA certificates which form the # certificate chain for the server certificate. Alternatively # the referenced file can be the same as SSLCertificateFile # when the CA certificates are directly appended to the server # certificate for convinience. #SSLCertificateChainFile /etc/apache2/ssl.crt/server-ca.crt # Certificate Authority (CA): # Set the CA certificate verification path where to find CA # certificates for client authentication or alternatively one # huge file containing all of them (file must be PEM encoded) # Note: Inside SSLCACertificatePath you need hash symlinks # to point to the certificate files. Use the provided # Makefile to update the hash symlinks after changes. #SSLCACertificatePath /etc/ssl/certs/ #SSLCACertificateFile /etc/apache2/ssl.crt/ca-bundle.crt # Certificate Revocation Lists (CRL): # Set the CA revocation path where to find CA CRLs for client # authentication or alternatively one huge file containing all # of them (file must be PEM encoded) # Note: Inside SSLCARevocationPath you need hash symlinks # to point to the certificate files. Use the provided # Makefile to update the hash symlinks after changes. #SSLCARevocationPath /etc/apache2/ssl.crl/ #SSLCARevocationFile /etc/apache2/ssl.crl/ca-bundle.crl # Client Authentication (Type): # Client certificate verification type and depth. Types are # none, optional, require and optional_no_ca. Depth is a # number which specifies how deeply to verify the certificate # issuer chain before deciding the certificate is not valid. #SSLVerifyClient require #SSLVerifyDepth 10 # Access Control: # With SSLRequire you can do per-directory access control based # on arbitrary complex boolean expressions containing server # variable checks and other lookup directives. The syntax is a # mixture between C and Perl. See the mod_ssl documentation # for more details. #<Location /> #SSLRequire ( %{SSL_CIPHER} !~ m/^(EXP|NULL)/ \ # and %{SSL_CLIENT_S_DN_O} eq "Snake Oil, Ltd." \ # and %{SSL_CLIENT_S_DN_OU} in {"Staff", "CA", "Dev"} \ # and %{TIME_WDAY} >= 1 and %{TIME_WDAY} <= 5 \ # and %{TIME_HOUR} >= 8 and %{TIME_HOUR} <= 20 ) \ # or %{REMOTE_ADDR} =~ m/^192\.76\.162\.[0-9]+$/ #</Location> # SSL Engine Options: # Set various options for the SSL engine. # o FakeBasicAuth: # Translate the client X.509 into a Basic Authorisation. This means that # the standard Auth/DBMAuth methods can be used for access control. The # user name is the `one line' version of the client's X.509 certificate. # Note that no password is obtained from the user. Every entry in the user # file needs this password: `xxj31ZMTZzkVA'. # o ExportCertData: # This exports two additional environment variables: SSL_CLIENT_CERT and # SSL_SERVER_CERT. These contain the PEM-encoded certificates of the # server (always existing) and the client (only existing when client # authentication is used). This can be used to import the certificates # into CGI scripts. # o StdEnvVars: # This exports the standard SSL/TLS related `SSL_*' environment variables. # Per default this exportation is switched off for performance reasons, # because the extraction step is an expensive operation and is usually # useless for serving static content. So one usually enables the # exportation for CGI and SSI requests only. # o StrictRequire: # This denies access when "SSLRequireSSL" or "SSLRequire" applied even # under a "Satisfy any" situation, i.e. when it applies access is denied # and no other module can change it. # o OptRenegotiate: # This enables optimized SSL connection renegotiation handling when SSL # directives are used in per-directory context. #SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory /usr/lib/cgi-bin> SSLOptions +StdEnvVars </Directory> # SSL Protocol Adjustments: # The safe and default but still SSL/TLS standard compliant shutdown # approach is that mod_ssl sends the close notify alert but doesn't wait for # the close notify alert from client. When you need a different shutdown # approach you can use one of the following variables: # o ssl-unclean-shutdown: # This forces an unclean shutdown when the connection is closed, i.e. no # SSL close notify alert is send or allowed to received. This violates # the SSL/TLS standard but is needed for some brain-dead browsers. Use # this when you receive I/O errors because of the standard approach where # mod_ssl sends the close notify alert. # o ssl-accurate-shutdown: # This forces an accurate shutdown when the connection is closed, i.e. a # SSL close notify alert is send and mod_ssl waits for the close notify # alert of the client. This is 100% SSL/TLS standard compliant, but in # practice often causes hanging connections with brain-dead browsers. Use # this only for browsers where you know that their SSL implementation # works correctly. # Notice: Most problems of broken clients are also related to the HTTP # keep-alive facility, so you usually additionally want to disable # keep-alive for those clients, too. Use variable "nokeepalive" for this. # Similarly, one has to force some clients to use HTTP/1.0 to workaround # their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and # "force-response-1.0" for this. BrowserMatch "MSIE [2-6]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 # MSIE 7 and newer should be able to use keepalive BrowserMatch "MSIE [17-9]" ssl-unclean-shutdown httpd.conf File Just a lot of stuff from html5 boiler plate, I will post it if need be Old htaccess file <IfModule mod_rewrite.c> # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] RewriteCond $1 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^(.*)/$ /$1 [r=301,L] # codeigniter direct RewriteCond $1 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^(.*)$ /index.php/$1 [L] </IfModule> Any Help would be hugely appreciated!!

  Read the article

• OpenVPN Client timing out

  - by Austin

  I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

  Read the article

• FreeBSD 8.1 unstable network connection

  - by frankcheong

  I have three FreeBSD 8.1 running on three different hardware and therefore consist of different network adapter as well (bce, bge and igb). I found that the network connection is kind of unstable which I have tried to scp some 10MB file and found that I cannot always get the files completed successfully. I have further checked with my network admin and he claim that the problem is being caused by the network driver which cannot support the load whereby he tried to ping using huge packet size (around 15k) and my server will drop packet consistently at a regular interval. I found that this statement may not be valid since the three server is using three different network drive and it would be quite impossible that the same problem is being caused by three different network adapter and thus different network driver. Since then I have tried to tune up the performance by playing around with the /etc/sysctl.conf figures with no luck. kern.ipc.somaxconn=1024 kern.ipc.shmall=3276800 kern.ipc.shmmax=1638400000 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # Required by pf net.inet.ip.forwarding=1 #Network Performance Tuning kern.ipc.maxsockbuf=16777216 net.inet.tcp.rfc1323=1 net.inet.tcp.sendbuf_max=16777216 net.inet.tcp.recvbuf_max=16777216 # Setting specifically for 1 or even 10Gbps network net.local.stream.sendspace=262144 net.local.stream.recvspace=262144 net.inet.tcp.local_slowstart_flightsize=10 net.inet.tcp.nolocaltimewait=1 net.inet.tcp.mssdflt=1460 net.inet.tcp.sendbuf_auto=1 net.inet.tcp.sendbuf_inc=16384 net.inet.tcp.recvbuf_auto=1 net.inet.tcp.recvbuf_inc=524288 net.inet.tcp.sendspace=262144 net.inet.tcp.recvspace=262144 net.inet.udp.recvspace=262144 kern.ipc.maxsockbuf=16777216 kern.ipc.nmbclusters=32768 net.inet.tcp.delayed_ack=1 net.inet.tcp.delacktime=100 net.inet.tcp.slowstart_flightsize=179 net.inet.tcp.inflight.enable=1 net.inet.tcp.inflight.min=6144 # Reduce the cache size of slow start connection net.inet.tcp.hostcache.expire=1 Our network admin also claim that they see quite a lot of network up and down from their cisco switch log while I cannot find any up down message inside the dmesg. Have further checked the netstat -s but dont have concrete idea. tcp: 133695291 packets sent 39408539 data packets (3358837321 bytes) 61868 data packets (89472844 bytes) retransmitted 24 data packets unnecessarily retransmitted 0 resends initiated by MTU discovery 50756141 ack-only packets (2148 delayed) 0 URG only packets 0 window probe packets 4372385 window update packets 39781869 control packets 134898031 packets received 72339403 acks (for 3357601899 bytes) 190712 duplicate acks 0 acks for unsent data 59339201 packets (3647021974 bytes) received in-sequence 114 completely duplicate packets (135202 bytes) 27 old duplicate packets 0 packets with some dup. data (0 bytes duped) 42090 out-of-order packets (60817889 bytes) 0 packets (0 bytes) of data after window 0 window probes 3953896 window update packets 64181 packets received after close 0 discarded for bad checksums 0 discarded for bad header offset fields 0 discarded because packet too short 45192 discarded due to memory problems 19945391 connection requests 1323420 connection accepts 0 bad connection attempts 0 listen queue overflows 0 ignored RSTs in the windows 21133581 connections established (including accepts) 21268724 connections closed (including 32737 drops) 207874 connections updated cached RTT on close 207874 connections updated cached RTT variance on close 132439 connections updated cached ssthresh on close 42392 embryonic connections dropped 72339338 segments updated rtt (of 69477829 attempts) 390871 retransmit timeouts 0 connections dropped by rexmit timeout 0 persist timeouts 0 connections dropped by persist timeout 0 Connections (fin_wait_2) dropped because of timeout 13990 keepalive timeouts 2 keepalive probes sent 13988 connections dropped by keepalive 173044 correct ACK header predictions 36947371 correct data packet header predictions 1323420 syncache entries added 0 retransmitted 0 dupsyn 0 dropped 1323420 completed 0 bucket overflow 0 cache overflow 0 reset 0 stale 0 aborted 0 badack 0 unreach 0 zone failures 1323420 cookies sent 0 cookies received 1864 SACK recovery episodes 18005 segment rexmits in SACK recovery episodes 26066896 byte rexmits in SACK recovery episodes 147327 SACK options (SACK blocks) received 87473 SACK options (SACK blocks) sent 0 SACK scoreboard overflow 0 packets with ECN CE bit set 0 packets with ECN ECT(0) bit set 0 packets with ECN ECT(1) bit set 0 successful ECN handshakes 0 times ECN reduced the congestion window udp: 5141258 datagrams received 0 with incomplete header 0 with bad data length field 0 with bad checksum 1 with no checksum 0 dropped due to no socket 129616 broadcast/multicast datagrams undelivered 0 dropped due to full socket buffers 0 not for hashed pcb 5011642 delivered 5016050 datagrams output 0 times multicast source filter matched sctp: 0 input packets 0 datagrams 0 packets that had data 0 input SACK chunks 0 input DATA chunks 0 duplicate DATA chunks 0 input HB chunks 0 HB-ACK chunks 0 input ECNE chunks 0 input AUTH chunks 0 chunks missing AUTH 0 invalid HMAC ids received 0 invalid secret ids received 0 auth failed 0 fast path receives all one chunk 0 fast path multi-part data 0 output packets 0 output SACKs 0 output DATA chunks 0 retransmitted DATA chunks 0 fast retransmitted DATA chunks 0 FR's that happened more than once to same chunk 0 intput HB chunks 0 output ECNE chunks 0 output AUTH chunks 0 ip_output error counter Packet drop statistics: 0 from middle box 0 from end host 0 with data 0 non-data, non-endhost 0 non-endhost, bandwidth rep only 0 not enough for chunk header 0 not enough data to confirm 0 where process_chunk_drop said break 0 failed to find TSN 0 attempt reverse TSN lookup 0 e-host confirms zero-rwnd 0 midbox confirms no space 0 data did not match TSN 0 TSN's marked for Fast Retran Timeouts: 0 iterator timers fired 0 T3 data time outs 0 window probe (T3) timers fired 0 INIT timers fired 0 sack timers fired 0 shutdown timers fired 0 heartbeat timers fired 0 a cookie timeout fired 0 an endpoint changed its cookiesecret 0 PMTU timers fired 0 shutdown ack timers fired 0 shutdown guard timers fired 0 stream reset timers fired 0 early FR timers fired 0 an asconf timer fired 0 auto close timer fired 0 asoc free timers expired 0 inp free timers expired 0 packet shorter than header 0 checksum error 0 no endpoint for port 0 bad v-tag 0 bad SID 0 no memory 0 number of multiple FR in a RTT window 0 RFC813 allowed sending 0 RFC813 does not allow sending 0 times max burst prohibited sending 0 look ahead tells us no memory in interface 0 numbers of window probes sent 0 times an output error to clamp down on next user send 0 times sctp_senderrors were caused from a user 0 number of in data drops due to chunk limit reached 0 number of in data drops due to rwnd limit reached 0 times a ECN reduced the cwnd 0 used express lookup via vtag 0 collision in express lookup 0 times the sender ran dry of user data on primary 0 same for above 0 sacks the slow way 0 window update only sacks sent 0 sends with sinfo_flags !=0 0 unordered sends 0 sends with EOF flag set 0 sends with ABORT flag set 0 times protocol drain called 0 times we did a protocol drain 0 times recv was called with peek 0 cached chunks used 0 cached stream oq's used 0 unread messages abandonded by close 0 send burst avoidance, already max burst inflight to net 0 send cwnd full avoidance, already max burst inflight to net 0 number of map array over-runs via fwd-tsn's ip: 137814085 total packets received 0 bad header checksums 0 with size smaller than minimum 0 with data size < data length 0 with ip length > max ip packet size 0 with header length < data size 0 with data length < header length 0 with bad options 0 with incorrect version number 1200 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 300 packets reassembled ok 137813009 packets for this host 530 packets for unknown/unsupported protocol 0 packets forwarded (0 packets fast forwarded) 61 packets not forwardable 0 packets received for unknown multicast group 0 redirects sent 137234598 packets sent from this host 0 packets sent with fabricated ip header 685307 output packets dropped due to no bufs, etc. 52 output packets discarded due to no route 300 output datagrams fragmented 1200 fragments created 0 datagrams that can't be fragmented 0 tunneling packets that can't find gif 0 datagrams with bad address in header icmp: 0 calls to icmp_error 0 errors not generated in response to an icmp message Output histogram: echo reply: 305 0 messages with bad code fields 0 messages less than the minimum length 0 messages with bad checksum 0 messages with bad length 0 multicast echo requests ignored 0 multicast timestamp requests ignored Input histogram: destination unreachable: 530 echo: 305 305 message responses generated 0 invalid return addresses 0 no return routes ICMP address mask responses are disabled igmp: 0 messages received 0 messages received with too few bytes 0 messages received with wrong TTL 0 messages received with bad checksum 0 V1/V2 membership queries received 0 V3 membership queries received 0 membership queries received with invalid field(s) 0 general queries received 0 group queries received 0 group-source queries received 0 group-source queries dropped 0 membership reports received 0 membership reports received with invalid field(s) 0 membership reports received for groups to which we belong 0 V3 reports received without Router Alert 0 membership reports sent arp: 376748 ARP requests sent 3207 ARP replies sent 245245 ARP requests received 80845 ARP replies received 326090 ARP packets received 267712 total packets dropped due to no ARP entry 108876 ARP entrys timed out 0 Duplicate IPs seen ip6: 2226633 total packets received 0 with size smaller than minimum 0 with data size < data length 0 with bad options 0 with incorrect version number 0 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 0 fragments that exceeded limit 0 packets reassembled ok 2226633 packets for this host 0 packets forwarded 0 packets not forwardable 0 redirects sent 2226633 packets sent from this host 0 packets sent with fabricated ip header 0 output packets dropped due to no bufs, etc. 8 output packets discarded due to no route 0 output datagrams fragmented 0 fragments created 0 datagrams that can't be fragmented 0 packets that violated scope rules 0 multicast packets which we don't join Input histogram: UDP: 2226633 Mbuf statistics: 962679 one mbuf 1263954 one ext mbuf 0 two or more ext mbuf 0 packets whose headers are not continuous 0 tunneling packets that can't find gif 0 packets discarded because of too many headers 0 failures of source address selection Source addresses selection rule applied: icmp6: 0 calls to icmp6_error 0 errors not generated in response to an icmp6 message 0 errors not generated because of rate limitation 0 messages with bad code fields 0 messages < minimum length 0 bad checksums 0 messages with bad length Histogram of error messages to be generated: 0 no route 0 administratively prohibited 0 beyond scope 0 address unreachable 0 port unreachable 0 packet too big 0 time exceed transit 0 time exceed reassembly 0 erroneous header field 0 unrecognized next header 0 unrecognized option 0 redirect 0 unknown 0 message responses generated 0 messages with too many ND options 0 messages with bad ND options 0 bad neighbor solicitation messages 0 bad neighbor advertisement messages 0 bad router solicitation messages 0 bad router advertisement messages 0 bad redirect messages 0 path MTU changes rip6: 0 messages received 0 checksum calculations on inbound 0 messages with bad checksum 0 messages dropped due to no socket 0 multicast messages dropped due to no socket 0 messages dropped due to full socket buffers 0 delivered 0 datagrams output netstat -m 516/5124/5640 mbufs in use (current/cache/total) 512/1634/2146/32768 mbuf clusters in use (current/cache/total/max) 512/1536 mbuf+clusters out of packet secondary zone in use (current/cache) 0/1303/1303/12800 4k (page size) jumbo clusters in use (current/cache/total/max) 0/0/0/6400 9k jumbo clusters in use (current/cache/total/max) 0/0/0/3200 16k jumbo clusters in use (current/cache/total/max) 1153K/9761K/10914K bytes allocated to network (current/cache/total) 0/0/0 requests for mbufs denied (mbufs/clusters/mbuf+clusters) 0/0/0 requests for jumbo clusters denied (4k/9k/16k) 0/8/6656 sfbufs in use (current/peak/max) 0 requests for sfbufs denied 0 requests for sfbufs delayed 0 requests for I/O initiated by sendfile 0 calls to protocol drain routines Anyone got an idea what might be the possible cause?

  Read the article

• Unable to PPTP through NAT on Cisco 881

  - by MasterRoot24

  I'm trying to connect to a PPTP server which is sat behind a Cisco 881 NAT router. The server is running Ubuntu Server 12.04 and is running Poptop pptpd as the PPTP daemon listening for connections. As discussed in my other question, I'm trying to setup a Cisco 881 router to replace my old Linksys WAG320N. This same server and WAN connection worked fine with the WAG320N with no special configuration, other than allowing 1723 in through the firewall. On the Cisco 881, I'm using the newer ip nat enable or NAT NVI to setup static routes in through the firewall for the services running behind the router. My reason being that I can't run another copy of my live DNS domains internally with local IP addresses in. For the purposes of this question, though, I have rebuilt the router with ip nat inside/outside style NAT'ing, but this issue is still apparent. HTTP/SMTP/IMAP etc. all work ok from both the WAN and LAN interfaces of the router. I'm only having issues with SIP (see other question) and PPTP. My issue is that the GRE doesn't appear to be passing through NAT correctly and one end of the connection is not receiving GRE traffic when it should be, so the server hangs up the connection. Here's an example of /var/log/syslog with debug enabled in /etc/pptpd.conf: Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: MGR: Launching /usr/sbin/pptpctrl to handle client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pppd options file = /etc/ppp/pptpd-options Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection started Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 1) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a START CTRL CONN RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 156 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 7) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Set parameters to 100000000 maxbps, 64 window size Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a OUT CALL RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Starting call (launching pppd, opening GRE) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pty_fd = 6 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: tty_fd = 7 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 32 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): program binary = /usr/sbin/pppd Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Dec 11 21:06:30 <HOSTNAME> pppd[22627]: pppd 2.4.5 started by root, uid 0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Using interface ppp0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Connect: ppp0 <--> /dev/pts/3 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: GRE: Bad checksum from pppd. Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 15) Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Got a SET LINK INFO packet with standard ACCMs Dec 11 21:07:00 <HOSTNAME> pppd[22627]: LCP: timeout sending Config-Requests Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Connection terminated. Dec 11 21:07:00 <HOSTNAME> avahi-daemon[1042]: Withdrawing workstation service for ppp0. Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Modem hangup Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Exit. Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Reaping child PPP[22627] Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection finished Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Exiting now Dec 11 21:07:00 <HOSTNAME> pptpd[5803]: MGR: Reaped child 22626 As far as Cisco are concerned, all I need is ip nat source static tcp <SERVER LAN IP> 1723 interface FastEthernet4 1723 but of course this doesn't seem to the be helping the GRE traffic through as it should. Trying the connection to the LAN IP of the server from the same LAN as the server (behind the router), the PPTP connection works fine, so I'm confident that the server's config is ok. Furthermore, all I needed on my WAG320N was to open 1723 in the firewall. Here's my current router config: ! ! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname xxx ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 xxx quit ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! ip domain list dmz.xxx.local ip domain list xxx.local ip domain name dmz.xxx.local ip name-server 192.168.1.x ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn xxx ! ! username admin privilege 15 secret 4 xxx username joe secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.x 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.x 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ! ! ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ! ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.1.0 0.0.0.255 ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 exec-timeout 15 0 login authentication local_auth line aux 0 exec-timeout 15 0 login authentication local_auth line vty 0 4 access-class 2 in login authentication local_auth length 0 transport input all ! ! end UPDATE 16/12/2012: The only progress that I have been able to make on this issue is that I'm confident that the issue is caused by the GRE tunnels (which are required for the PPTP connection to complete) are being blocked. When attempting a connection, I can see in show ip nat nvi translations that both a TCP translation on 1723 is setup and also a GRE translation is setup also. I appear to be able to see GRE related packets on the LAN that the server is on, so I am lead to believe that the server is sending(?) GRE packets, however running Wireshark on a client PC when attempting a connection shows absolutely no GRE packets. Whilst there are no configuration directives in my config posted above (that I can pin point) which would specifically block them, it would appear that the GRE packets are not being allowed in/out of the router's firewall, even though a NAT translation entry is setup to the server's LAN address. Would anyone be able to provide me with some help to ensure that GRE packets are not blocked by the router's firewall, so that this can be ruled out as a possible issue please?

  Read the article

• Generating moderately interesting images

  - by Williham Totland

  Abstract: Can you propose a mathematical-ish algorithm over a plane of pixels that will generate a moderately interesting image, preferably one that on the whole resembles something? The story thus far: Once upon a time I decided in an effort to reduce cycle waste on my (admittedly too) numerous computers, and set out to generate images in a moderately interesting fashion; using a PRNG and some clever math to create images that would, on the whole, resemble something. Or at least, that was the plan. As it turns out, clever math requires being a clever mathematician; this I am not. At some length I arrived at a method that preferred straight lines (as these are generally the components of which our world is made), perhaps too strongly. The result is mildly interesting; resembling, perhaps, city grids as such: Now for the question proper: Given the source code of this little program; can you improve upon it and propose a method that gives somewhat more interesting results? (e.g. not city grids, but perhaps faces, animals, geography, what have you) This is also meant as a sort of challenge; I suppose and as such I've set down some completely arbitrary and equally optional rules: The comments in the code says it all really. Suggestions and "solutions" should edit the algorithm itself, not the surrounding framework, except as for to fix errors that prevents the sample from compiling. The code should compile cleanly with a standard issue C compiler. (If the example provided doesn't, oops! Tell me, and I'll fix. :) The method should, though again, this is optional, not need to elicit help from your friendly neighborhood math library. Solutions should probably be deliverable by simply yanking out whatever is between the snip lines (the ones that say you should not edit above and below, respectively), with a statement to the effect of what you need to add to the preamble in particular. The code requires a C compiler and libpng to build; I'm not entirely confident that the MinGW compiler provides the necessities, but I would be surprised if it didn't. For Debian you'll want the libpng-dev package, and for Mac OS X you'll want the XCode tools.. The source code can be downloaded here. Warning: Massive code splurge incoming! // compile with gcc -o imggen -lpng imggen.c // optionally with -DITERATIONS=x, where x is an appropriate integer // If you're on a Mac or using MinGW, you may have to fiddle with the linker flags to find the library and includes. #include <stdio.h> #include <stdlib.h> #include <png.h> #ifdef ITERATIONS #define REPEAT #endif // ITERATIONS // YOU MAY CHANGE THE FOLLOWING DEFINES #define WIDTH 320 #define HEIGHT 240 // YOU MAY REPLACE THE FOLLOWING DEFINES AS APPROPRIATE #define INK 16384 void writePNG (png_bytepp imageBuffer, png_uint_32 width, png_uint_32 height, int iteration) { char *fname; asprintf(&fname, "out.%d.png", iteration); FILE *fp = fopen(fname, "wb"); if (!fp) return; png_structp png_ptr = png_create_write_struct(PNG_LIBPNG_VER_STRING, NULL, NULL, NULL); png_infop info_ptr = png_create_info_struct(png_ptr); png_init_io(png_ptr, fp); png_set_filter(png_ptr, PNG_FILTER_TYPE_DEFAULT, PNG_FILTER_NONE); png_set_compression_level(png_ptr, Z_BEST_COMPRESSION); png_set_IHDR(png_ptr, info_ptr, width, height, 8, PNG_COLOR_TYPE_GRAY, PNG_INTERLACE_NONE, PNG_COMPRESSION_TYPE_DEFAULT, PNG_FILTER_TYPE_DEFAULT); png_set_rows(png_ptr, info_ptr, imageBuffer); png_set_invert_mono(png_ptr); /// YOU MAY COMMENT OUT THIS LINE png_write_png(png_ptr, info_ptr, PNG_TRANSFORM_IDENTITY, NULL); png_destroy_write_struct(&png_ptr, &info_ptr); fclose(fp); free(fname); } int main (int argc, const char * argv[]) { png_uint_32 height = HEIGHT, width = WIDTH; int iteration = 1; #ifdef REPEAT for (iteration = 1; iteration <= ITERATIONS; iteration++) { #endif // REPEAT png_bytepp imageBuffer = malloc(sizeof(png_bytep) * height); for (png_uint_32 i = 0; i < height; i++) { imageBuffer[i] = malloc(sizeof(png_byte) * width); for (png_uint_32 j = 0; j < width; j++) { imageBuffer[i][j] = 0; } } /// CUT ACROSS THE DASHED LINES /// ------------------------------------------- /// NO EDITING ABOVE THIS LINE; EXCEPT AS NOTED int ink = INK; int x = rand() % width, y = rand() % height; int xdir = (rand() % 2)?1:-1; int ydir = (rand() % 2)?1:-1; while (ink) { imageBuffer[y][x] = 255; --ink; xdir += (rand() % 2)?(1):(-1); ydir += (rand() % 2)?(1):(-1); if (ydir > 0) { ++y; } else if (ydir < 0) { --y; } if (xdir > 0) { ++x; } else if (xdir < 0) { --x; } if (x == -1 || y == -1 || x == width || y == height || x == y && x == 0) { x = rand() % width; y = rand() % height; xdir = (rand() % 2)?1:-1; ydir = (rand() % 2)?1:-1; } } /// NO EDITING BELOW THIS LINE /// ------------------------------------------- writePNG(imageBuffer, width, height, iteration); for (png_uint_32 i = 0; i < height; i++) { free(imageBuffer[i]); } free(imageBuffer); #ifdef REPEAT } #endif // REPEAT return 0; } Note: While this question doesn't strictly speaking seem "answerable" as such; I still believe that it can give rise to some manner of "right" answer. Maybe. Happy hunting.

  Read the article

• How to use Ninject with XNA?

  - by Rosarch

  I'm having difficulty integrating Ninject with XNA. static class Program { /** * The main entry point for the application. */ static void Main(string[] args) { IKernel kernel = new StandardKernel(NinjectModuleManager.GetModules()); CachedContentLoader content = kernel.Get<CachedContentLoader>(); // stack overflow here MasterEngine game = kernel.Get<MasterEngine>(); game.Run(); } } // constructor for the game public MasterEngine(IKernel kernel) : base(kernel) { this.inputReader = kernel.Get<IInputReader>(); graphicsDeviceManager = kernel.Get<GraphicsDeviceManager>(); Components.Add(kernel.Get<GamerServicesComponent>()); // Tell the loader to look for all files relative to the "Content" directory. Assets = kernel.Get<CachedContentLoader>(); //Sets dimensions of the game window graphicsDeviceManager.PreferredBackBufferWidth = 800; graphicsDeviceManager.PreferredBackBufferHeight = 600; graphicsDeviceManager.ApplyChanges(); IsMouseVisible = false; } Ninject.cs: using System; using System.Collections.Generic; using System.Linq; using System.Text; using Ninject.Modules; using HWAlphaRelease.Controller; using Microsoft.Xna.Framework; using Nuclex.DependencyInjection.Demo.Scaffolding; using Microsoft.Xna.Framework.Content; using Microsoft.Xna.Framework.Graphics; namespace HWAlphaRelease { public static class NinjectModuleManager { public static NinjectModule[] GetModules() { return new NinjectModule[1] { new GameModule() }; } /// <summary>Dependency injection rules for the main game instance</summary> public class GameModule : NinjectModule { #region class ServiceProviderAdapter /// <summary>Delegates to the game's built-in service provider</summary> /// <remarks> /// <para> /// When a class' constructor requires an IServiceProvider, the dependency /// injector cannot just construct a new one and wouldn't know that it has /// to create an instance of the Game class (or take it from the existing /// Game instance). /// </para> /// <para> /// The solution, then, is this small adapter that takes a Game instance /// and acts as if it was a freely constructable IServiceProvider implementation /// while in reality, it delegates all lookups to the Game's service container. /// </para> /// </remarks> private class ServiceProviderAdapter : IServiceProvider { /// <summary>Initializes a new service provider adapter for the game</summary> /// <param name="game">Game the service provider will be taken from</param> public ServiceProviderAdapter(Game game) { this.gameServices = game.Services; } /// <summary>Retrieves a service from the game service container</summary> /// <param name="serviceType">Type of the service that will be retrieved</param> /// <returns>The service that has been requested</returns> public object GetService(Type serviceType) { return this.gameServices; } /// <summary>Game services container of the Game instance</summary> private GameServiceContainer gameServices; } #endregion // class ServiceProviderAdapter #region class ContentManagerAdapter /// <summary>Delegates to the game's built-in ContentManager</summary> /// <remarks> /// This provides shared access to the game's ContentManager. A dependency /// injected class only needs to require the ISharedContentService in its /// constructor and the dependency injector will automatically resolve it /// to this adapter, which delegates to the Game's built-in content manager. /// </remarks> private class ContentManagerAdapter : ISharedContentService { /// <summary>Initializes a new shared content manager adapter</summary> /// <param name="game">Game the content manager will be taken from</param> public ContentManagerAdapter(Game game) { this.contentManager = game.Content; } /// <summary>Loads or accesses shared game content</summary> /// <typeparam name="AssetType">Type of the asset to be loaded or accessed</typeparam> /// <param name="assetName">Path and name of the requested asset</param> /// <returns>The requested asset from the the shared game content store</returns> public AssetType Load<AssetType>(string assetName) { return this.contentManager.Load<AssetType>(assetName); } /// <summary>The content manager this instance delegates to</summary> private ContentManager contentManager; } #endregion // class ContentManagerAdapter /// <summary>Initializes the dependency configuration</summary> public override void Load() { // Allows access to the game class for any components with a dependency // on the 'Game' or 'DependencyInjectionGame' classes. Bind<MasterEngine>().ToSelf().InSingletonScope(); Bind<NinjectGame>().To<MasterEngine>().InSingletonScope(); Bind<Game>().To<MasterEngine>().InSingletonScope(); // Let the dependency injector construct a graphics device manager for // all components depending on the IGraphicsDeviceService and // IGraphicsDeviceManager interfaces Bind<GraphicsDeviceManager>().ToSelf().InSingletonScope(); Bind<IGraphicsDeviceService>().To<GraphicsDeviceManager>().InSingletonScope(); Bind<IGraphicsDeviceManager>().To<GraphicsDeviceManager>().InSingletonScope(); // Some clever adapters that hand out the Game's IServiceProvider and allow // access to its built-in ContentManager Bind<IServiceProvider>().To<ServiceProviderAdapter>().InSingletonScope(); Bind<ISharedContentService>().To<ContentManagerAdapter>().InSingletonScope(); Bind<IInputReader>().To<UserInputReader>().InSingletonScope().WithConstructorArgument("keyMapping", Constants.DEFAULT_KEY_MAPPING); Bind<CachedContentLoader>().ToSelf().InSingletonScope().WithConstructorArgument("rootDir", "Content"); } } } } NinjectGame.cs /// <summary>Base class for Games making use of Ninject</summary> public class NinjectGame : Game { /// <summary>Initializes a new Ninject game instance</summary> /// <param name="kernel">Kernel the game has been created by</param> public NinjectGame(IKernel kernel) { Type ownType = this.GetType(); if(ownType != typeof(Game)) { kernel.Bind<NinjectGame>().To<MasterEngine>().InSingletonScope(); } kernel.Bind<Game>().To<NinjectGame>().InSingletonScope(); } } } // namespace Nuclex.DependencyInjection.Demo.Scaffolding When I try to get the CachedContentLoader, I get a stack overflow exception. I'm basing this off of this tutorial, but I really have no idea what I'm doing. Help?

  Read the article

• Ninject.ActivationException: Error activating IMainLicense

  - by Stefan Karlsson

  Im don't know fully how Ninject works thats wye i ask this question here to figure out whats wrong. If i create a empty constructor in ClaimsSecurityService it gets hit. This is my error: Error activating IMainLicense No matching bindings are available, and the type is not self-bindable. Activation path: 3) Injection of dependency IMainLicense into parameter mainLicenses of constructor of type ClaimsSecurityService 2) Injection of dependency ISecurityService into parameter securityService of constructor of type AccountController 1) Request for AccountController Stack: Ninject.KernelBase.Resolve(IRequest request) +474 Ninject.Planning.Targets.Target`1.GetValue(Type service, IContext parent) +153 Ninject.Planning.Targets.Target`1.ResolveWithin(IContext parent) +747 Ninject.Activation.Providers.StandardProvider.GetValue(IContext context, ITarget target) +269 Ninject.Activation.Providers.<>c__DisplayClass4.<Create>b__2(ITarget target) +69 System.Linq.WhereSelectArrayIterator`2.MoveNext() +66 System.Linq.Buffer`1..ctor(IEnumerable`1 source) +216 System.Linq.Enumerable.ToArray(IEnumerable`1 source) +77 Ninject.Activation.Providers.StandardProvider.Create(IContext context) +847 Ninject.Activation.Context.ResolveInternal(Object scope) +218 Ninject.Activation.Context.Resolve() +277 Ninject.<>c__DisplayClass15.<Resolve>b__f(IBinding binding) +86 System.Linq.WhereSelectEnumerableIterator`2.MoveNext() +145 System.Linq.Enumerable.SingleOrDefault(IEnumerable`1 source) +4059897 Ninject.Planning.Targets.Target`1.GetValue(Type service, IContext parent) +169 Ninject.Planning.Targets.Target`1.ResolveWithin(IContext parent) +747 Ninject.Activation.Providers.StandardProvider.GetValue(IContext context, ITarget target) +269 Ninject.Activation.Providers.<>c__DisplayClass4.<Create>b__2(ITarget target) +69 System.Linq.WhereSelectArrayIterator`2.MoveNext() +66 System.Linq.Buffer`1..ctor(IEnumerable`1 source) +216 System.Linq.Enumerable.ToArray(IEnumerable`1 source) +77 Ninject.Activation.Providers.StandardProvider.Create(IContext context) +847 Ninject.Activation.Context.ResolveInternal(Object scope) +218 Ninject.Activation.Context.Resolve() +277 Ninject.<>c__DisplayClass15.<Resolve>b__f(IBinding binding) +86 System.Linq.WhereSelectEnumerableIterator`2.MoveNext() +145 System.Linq.Enumerable.SingleOrDefault(IEnumerable`1 source) +4059897 Ninject.Web.Mvc.NinjectDependencyResolver.GetService(Type serviceType) +145 System.Web.Mvc.DefaultControllerActivator.Create(RequestContext requestContext, Type controllerType) +87 [InvalidOperationException: An error occurred when trying to create a controller of type 'Successful.Struct.Web.Controllers.AccountController'. Make sure that the controller has a parameterless public constructor.] System.Web.Mvc.DefaultControllerActivator.Create(RequestContext requestContext, Type controllerType) +247 System.Web.Mvc.DefaultControllerFactory.GetControllerInstance(RequestContext requestContext, Type controllerType) +438 System.Web.Mvc.DefaultControllerFactory.CreateController(RequestContext requestContext, String controllerName) +257 System.Web.Mvc.MvcHandler.ProcessRequestInit(HttpContextBase httpContext, IController& controller, IControllerFactory& factory) +326 System.Web.Mvc.MvcHandler.BeginProcessRequest(HttpContextBase httpContext, AsyncCallback callback, Object state) +157 System.Web.Mvc.MvcHandler.BeginProcessRequest(HttpContext httpContext, AsyncCallback callback, Object state) +88 System.Web.Mvc.MvcHandler.System.Web.IHttpAsyncHandler.BeginProcessRequest(HttpContext context, AsyncCallback cb, Object extraData) +50 System.Web.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +301 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +155 Account controller: public class AccountController : Controller { private readonly ISecurityService _securityService; public AccountController(ISecurityService securityService) { _securityService = securityService; } // // GET: /Account/Login [AllowAnonymous] public ActionResult Login(string returnUrl) { ViewBag.ReturnUrl = returnUrl; return View(); } } NinjectWebCommon: using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.Http; using System.Web.Http.Dependencies; using Microsoft.Web.Infrastructure.DynamicModuleHelper; using Ninject; using Ninject.Extensions.Conventions; using Ninject.Parameters; using Ninject.Syntax; using Ninject.Web.Common; using Successful.Struct.Web; [assembly: WebActivator.PreApplicationStartMethod(typeof(NinjectWebCommon), "Start")] [assembly: WebActivator.ApplicationShutdownMethodAttribute(typeof(NinjectWebCommon), "Stop")] namespace Successful.Struct.Web { public static class NinjectWebCommon { private static readonly Bootstrapper Bootstrapper = new Bootstrapper(); /// <summary> /// Starts the application /// </summary> public static void Start() { DynamicModuleUtility.RegisterModule(typeof(OnePerRequestHttpModule)); DynamicModuleUtility.RegisterModule(typeof(NinjectHttpModule)); Bootstrapper.Initialize(CreateKernel); } /// <summary> /// Stops the application. /// </summary> public static void Stop() { Bootstrapper.ShutDown(); } /// <summary> /// Creates the kernel that will manage your application. /// </summary> /// <returns>The created kernel.</returns> private static IKernel CreateKernel() { var kernel = new StandardKernel(); kernel.Bind<Func<IKernel>>().ToMethod(ctx => () => new Bootstrapper().Kernel); kernel.Bind<IHttpModule>().To<HttpApplicationInitializationHttpModule>(); kernel.Load("Successful*.dll"); kernel.Bind(x => x.FromAssembliesMatching("Successful*.dll") .SelectAllClasses() .BindAllInterfaces() ); GlobalConfiguration.Configuration.DependencyResolver = new NinjectResolver(kernel); RegisterServices(kernel); return kernel; } /// <summary> /// Load your modules or register your services here! /// </summary> /// <param name="kernel">The kernel.</param> private static void RegisterServices(IKernel kernel) { } } public class NinjectResolver : NinjectScope, IDependencyResolver { private readonly IKernel _kernel; public NinjectResolver(IKernel kernel) : base(kernel) { _kernel = kernel; } public IDependencyScope BeginScope() { return new NinjectScope(_kernel.BeginBlock()); } } public class NinjectScope : IDependencyScope { protected IResolutionRoot ResolutionRoot; public NinjectScope(IResolutionRoot kernel) { ResolutionRoot = kernel; } public object GetService(Type serviceType) { var request = ResolutionRoot.CreateRequest(serviceType, null, new Parameter[0], true, true); return ResolutionRoot.Resolve(request).SingleOrDefault(); } public IEnumerable<object> GetServices(Type serviceType) { var request = ResolutionRoot.CreateRequest(serviceType, null, new Parameter[0], true, true); return ResolutionRoot.Resolve(request).ToList(); } public void Dispose() { var disposable = (IDisposable)ResolutionRoot; if (disposable != null) disposable.Dispose(); ResolutionRoot = null; } } } ClaimsSecurityService: public class ClaimsSecurityService : ISecurityService { private const string AscClaimsIdType = "http://schemas.microsoft.com/accesscontrolservice/2010/07/claims/identityprovider"; private const string SuccessfulStructWebNamespace = "Successful.Struct.Web"; private readonly IMainLicense _mainLicenses; private readonly ICompany _companys; private readonly IAuthTokenService _authService; [Inject] public IApplicationContext ApplicationContext { get; set; } [Inject] public ILogger<LocationService> Logger { get; set; } public ClaimsSecurityService(IMainLicense mainLicenses, ICompany companys, IAuthTokenService authService) { _mainLicenses = mainLicenses; _companys = companys; _authService = authService; } }

  Read the article

• Delphi - Proper way to page though data.

  - by Brad

  I have a string list (TStrings) that has a couple thousand items in it. I need to process them in groups of 100. I basically want to know what the best way to do the loop is in Delphi. I'm hitting a brick wall when I'm trying to figure it out. Thanks unit Unit2; interface uses Windows, Messages, SysUtils, Variants, Classes, Graphics, Controls, Forms, Dialogs, StdCtrls; type TForm2 = class(TForm) Memo1: TMemo; Memo2: TMemo; Button1: TButton; procedure Button1Click(Sender: TObject); private { Private declarations } public { Public declarations } end; var Form2: TForm2; implementation Uses math; {$R *.dfm} procedure TForm2.Button1Click(Sender: TObject); var I:Integer; pages:Integer; str:string; begin pages:= ceil(memo1.Lines.Count/100) ; memo2.Lines.add('Total Pages: '+inttostr(pages)); memo2.Lines.add('Total Items: '+inttostr(memo1.Lines.Count)); // Should just do in batches of 100 VS entire list for I := 0 to memo1.lines.Count - 1 do begin if str '' then str:= str+#10+ memo1.Lines.Strings[i] else str:= memo1.Lines.Strings[i]; end; //I need to stop here every 100 items, then process the items. memo2.Lines.Add(str); end; end. Example form object Form2: TForm2 Left = 0 Top = 0 Caption = 'Form2' ClientHeight = 245 ClientWidth = 527 Color = clBtnFace Font.Charset = DEFAULT_CHARSET Font.Color = clWindowText Font.Height = -11 Font.Name = 'Tahoma' Font.Style = [] OldCreateOrder = False PixelsPerInch = 96 TextHeight = 13 object Memo1: TMemo Left = 16 Top = 8 Width = 209 Height = 175 Lines.Strings = ( '4xlt columbia thunder storm jacket' '5 things about thunder storms' 'a thunder storm with a lot of thunder ' 'and lighting sccreensaver' 'a thunder storm with a lot of thunder ' 'and lighting screensaver with no nag ' 'screens' 'all about thunder storms' 'all about thunderstorms for kids' 'amazing tornado videos and ' 'thunderstorm videos' 'are thunder storms louder in ohio?' 'bad thunder storms' 'bathing in thunder storm' 'best thunderstorm pictures' 'cartoon thunder storms' 'celtic thunder storm' 'central valley thunder storm' 'chicago thunderstorm pictures' 'cool thunderstorm pictures' 'current thunderstorm warnings' 'does thunder storms in december mean ' 'snow will be coming' 'facts about thunderstorms for kids' 'facts on thunderstorms for kids' 'fedex thunderstorm video' 'florida thunderstorms facts' 'free relaxing thunderstorm music' 'free soothing thunderstorm sounds ' 'online' 'free thunderstorm mp3' 'free thunderstorm mp3 download' 'free thunderstorm mp3 downloads' 'free thunderstorm mp3s' 'free thunderstorm music' 'free thunderstorm pictures' 'free thunderstorm sound effects' 'free thunderstorm sounds' 'free thunderstorm sounds cd' 'free thunderstorm sounds mp3' 'free thunderstorm sounds online' 'free thunderstorm soundscape' 'free thunderstorm video' 'free thunderstorm video download' 'free thunderstorm videos' 'god of storm and thunder' 'horses storm thunder rain' 'how do thunder storms form' 'how far away is a thunder storm' 'how long do thunder storms last' 'ice cube in a thunder storm' 'indoor thunderstorm safety tips' 'information about thunderstorms for kids' 'interesting thunderstorm facts' 'is it dangerous to shower during thunder ' 'storm' 'is there frequently thunder during snow ' 'storms' 'isolated thunderstorms' 'it'#39's just a thunder storm baby there is ' 'nothing you should fear lyrics' 'lightning & thunder storm safety' 'lightning and thunderstorm facts' 'lightning and thunderstorms facts' 'lightning and thunderstorms for kids' 'listen to thunderstorm sounds online' 'mississauga thunder storm' 'nature sounds free mp3 thunder storm' 'only about thunderstorms facts' 'original storm deep thunderstick' 'phone use during thunder storms' 'pictures of thunderstorms' 'pocono thunder storm' 'posters of thunder storms' 'power rangers ninja storm' 'power rangers thunder storm' 'power rangers thunder storm cast' 'power rangers thunder storm games' 'power rangers thunder storm morphers' 'power rangers thunder storm part 1' 'power rangers thunder storm part 2' 'power rangers thunderstorm' 'power rangers thunderstorm cannon' 'power rangers thunderstorm deluxe ' 'megazord' 'power rangers thunderstorm games' 'power rangers thunderstorm megazord' 'power rangers thunderstorm part 2' 'power rangers thunderstorm pictures' 'power rnager ninja storm thunder staff' 'powerful thunder and lightning storms' 'precambrian thunder storms' 'rain thunderstorm mp3' 'rain thunderstorm pictures' 'relaxing thunderstorm music' 'reminds me of ohio river thunder lighten ' 'storms' 'sacramento thunder storm' 'safety tips for when your caught in a ' 'thunder storm' 'scattered thunderstorms' 'schemer puts his head in the thunder ' 'storm' 'sedative thunder storm' 'server thunder storms' 'severe supercell thunderstorm pictures' 'severe thunder storm pictures' 'severe thunder storms' 'severe thunderstorm facts' 'severe thunderstorm pictures' 'severe thunderstorm pictures hail' 'severe thunderstorm pictures in alberta' 'severe thunderstorm pictures tornado' 'severe thunderstorm safety' 'severe thunderstorm safety tips' 'severe thunderstorm videos' 'severe thunderstorm warning' 'severe thunderstorm warning los ' 'angeles' 'severe thunderstorm warning signs' 'severe thunderstorm warnings' 'severe thunderstorms' 'severe thunderstorms facts' 'shakespeare use thunder storm for ' 'cosmic disorder julius caesar' 'soothing thunderstorm sounds online' 'sound effects of severe thunder storm' 'sound of rain storm finger snapping ' 'thunder chorus' 'split thunder storm' 'storm 3d thunder power' 'storm dark thunder' 'storm dark thunder bowling ball' 'storm dark thunder bowling ball sale' 'storm dark thunder for sale' 'storm dark thunder pearl' 'storm dark thunder pearl bowling ball' 'storm dark thunder review' 'storm dark thunder shirt' 'storm dark thunderball' 'storm deep thunder' 'storm deep thunder 11' 'storm deep thunder 15' 'storm deep thunder 15 lure' 'storm deep thunder 2' 'storm deep thunder lures' 'storm deep thunderstick' 'storm deep thunderstick crankbaits' 'storm deep thunderstick dts09' 'storm deep thunderstick jr' 'storm deep thunderstick lures' 'storm deep thundersticks' 'storm rolling thunder 3 ball roller' 'storm rolling thunder bowling bag' 'storm rolling thunder three ball bowling ' 'bag' 'storm shallow thunder' 'storm shallow thunder 15' 'storm thunder claw' 'storm thunder craw' 'storm watches thunder' 'storms with constant lightning and ' 'thunder non-stop' 'supercell thunder storms' 'supercell thunderstorm pictures' 'supercell thunderstorms' 'swimming pools thunder storms' 'tampa + lightning strikes + thunder ' 'storms' 'texas thunderstorm pictures' 'texas thunderstorm warnings' 'thunder and lightning storm' 'thunder and lighting storms' 'thunder and lightning storms' 'thunder bay snow storm video' 'thunder storm' 'thunder storm and windmill' 'thunder storm cd' 'thunder storm cloud' 'thunder storm clouds' 'thunder storm dog peppermint oil' 'thunder storm in winter' 'thunder storm in winter and weather ' 'prediction' 'thunder storm lx-3 & road blaster psx ' 'download' 'thunder storm occurances' 'thunder storm photos' 'thunder storm poems' 'thunder storm safety' 'thunder storm sign' 'thunder storm sounds' 'thunder storms' 'thunder storms and deaths' 'thunder storms and ilghting' 'thunder storms and lighting' 'thunder storms cd' 'thunder storms in the arctic arctic ' 'weather' 'thunder storms in winter' 'thunder storms on you tub' 'thunder storms pics' 'thunder storms with rain' 'thunderstorm' 'thunderstorm backgrounds' 'thunderstorm capital' 'thunderstorm capital 2008 dorfman' 'thunderstorm capital in boston' 'thunderstorm capital llc' 'thunderstorm capital of canada' 'thunderstorm capital of the us' 'thunderstorm capital of the world' 'thunderstorm facts' 'thunderstorm facts for kids' 'thunderstorm facts hail' 'thunderstorm facts tornadoes' 'thunderstorm mp3' 'thunderstorm mp3 download' 'thunderstorm mp3 download free' 'thunderstorm mp3 downloads' 'thunderstorm mp3 downloads free' 'thunderstorm mp3 files' 'thunderstorm mp3 free' 'thunderstorm mp3 free download' 'thunderstorm mp3 free downloads' 'thunderstorm mp3 torrent' 'thunderstorm mp3s' 'thunderstorm music' 'thunderstorm music cd' 'thunderstorm music downloads' 'thunderstorm music free' 'thunderstorm music playlists' 'thunderstorm music rain' 'thunderstorm pics' 'thunderstorm pictures' 'thunderstorm pictures for kids' 'thunderstorm safety' 'thunderstorm safety for kids' 'thunderstorm safety precautions' 'thunderstorm safety procedures' 'thunderstorm safety rules' 'thunderstorm safety tips' 'thunderstorm safety tips for kids' 'thunderstorm safety tips shelter' 'thunderstorm safety tips trees' 'thunderstorm sound effects' 'thunderstorm sound effects cd' 'thunderstorm sound effects download' 'thunderstorm sound effects free' 'thunderstorm sound effects free ' 'download' 'thunderstorm sound effects free music ' 'feature audio' 'thunderstorm sound effects mp3' 'thunderstorm sound effects rain' 'thunderstorm sounds' 'thunderstorm sounds cd' 'thunderstorm sounds download' 'thunderstorm sounds for sleep' 'thunderstorm sounds for sleeping' 'thunderstorm sounds free' 'thunderstorm sounds free download' 'thunderstorm sounds free downloads' 'thunderstorm sounds mp3' 'thunderstorm sounds mp3 download' 'thunderstorm sounds mp3 free' 'thunderstorm sounds online' 'thunderstorm sounds online for free' 'thunderstorm sounds online free' 'thunderstorm sounds sleep' 'thunderstorm sounds streaming' 'thunderstorm sounds torrent' 'thunderstorm soundscape' 'thunderstorm soundscapes' 'thunderstorm video' 'thunderstorm video clips' 'thunderstorm video download' 'thunderstorm video downloads' 'thunderstorm videos' 'thunderstorm videos for kids' 'thunderstorm videos lightning' 'thunderstorm videos online' 'thunderstorm wallpaper' 'thunderstorm warning' 'thunderstorm warning brisbane' 'thunderstorm warning definition' 'thunderstorm warning los angeles' 'thunderstorm warning san diego' 'thunderstorm warning san mateo county' 'thunderstorm warning santa barbara' 'thunderstorm warning santa clara' 'thunderstorm warning santa clara ' 'county' 'thunderstorm warning signal' 'thunderstorm warning signs' 'thunderstorm warning vs watch' 'thunderstorm warnings' 'thunderstorm warnings and watches' 'thunderstorm warnings for nj' 'thunderstorm warnings qld' 'thunderstorms' 'thunderstorms facts' 'thunderstorms facts for kids' 'thunderstorms for kids' 'tornados and thunder storms animated' 'understanding thunderstorms for kids' 'watch thunderstorm videos' 'weather underground forecast ' 'thunderstorms' 'what causes thunder storms' 'what is a thunder storm' 'where d thunder storms occur') TabOrder = 0 end object Memo2: TMemo Left = 240 Top = 8 Width = 265 Height = 129 Lines.Strings = ( 'Memo2') TabOrder = 1 end object Button1: TButton Left = 384 Top = 184 Width = 75 Height = 25 Caption = 'Button1' TabOrder = 2 OnClick = Button1Click end end

  Read the article

• CoreData update problems

  - by kpower

  My app makes updates in background thread then saves context changes. And in main context there is a table view that works with NSFetchedResultsController. For some time updates work correctly, but then exception is thrown. To check this I've added NSLog(@"%@", [self.controller fetchedObjects]); to -controllerDidChangeContent:. Here is what I got: "<PRBattle: 0x6d30530> (entity: PRBattle; id: 0x6d319d0 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p2> ; data: {\n battleId = \"-1\";\n finishedAt = \"2012-11-06 11:37:36 +0000\";\n opponent = \"0x6d2f730 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PROpponent/p1>\";\n opponentScore = nil;\n score = nil;\n status = 4;\n})", "<PRBattle: 0x6d306f0> (entity: PRBattle; id: 0x6d319f0 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p1> ; data: {\n battleId = \"-1\";\n finishedAt = \"2012-11-06 11:37:36 +0000\";\n opponent = \"0x6d2ddb0 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PROpponent/p3>\";\n opponentScore = nil;\n score = nil;\n status = 4;\n})", "<PRBattle: 0x6d30830> (entity: PRBattle; id: 0x6d31650 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p11> ; data: <fault>)", "<PRBattle: 0x6d306b0> (entity: PRBattle; id: 0x6d319e0 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p5> ; data: {\n battleId = 325;\n finishedAt = nil;\n opponent = \"0x6d2f730 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PROpponent/p1>\";\n opponentScore = 91;\n score = 59;\n status = 3;\n})", "<PRBattle: 0x6d30730> (entity: PRBattle; id: 0x6d31a00 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p6> ; data: {\n battleId = 323;\n finishedAt = nil;\n opponent = \"0x6d2ddb0 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PROpponent/p3>\";\n opponentScore = 0;\n score = 0;\n status = 3;\n})", "<PRBattle: 0x6d307b0> (entity: PRBattle; id: 0x6d31630 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p9> ; data: {\n battleId = 370;\n finishedAt = \"2012-11-06 14:24:14 +0000\";\n opponent = \"0x79a8e90 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PROpponent/p2>\";\n opponentScore = 180;\n score = 180;\n status = 4;\n})", "<PRBattle: 0x6d307f0> (entity: PRBattle; id: 0x6d31640 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p10> ; data: {\n battleId = 309;\n finishedAt = \"2012-11-02 01:19:27 +0000\";\n opponent = \"0x79a8e90 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PROpponent/p2>\";\n opponentScore = 120;\n score = 240;\n status = 4;\n})", "<PRBattle: 0x6d30770> (entity: PRBattle; id: 0x6d31620 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p7> ; data: {\n battleId = 315;\n finishedAt = \"2012-11-02 02:26:24 +0000\";\n opponent = \"0x79a8e90 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PROpponent/p2>\";\n opponentScore = 119;\n score = 179;\n status = 4;\n})" ) Faulted object (0xe972610) here causes crash. I've logged data during update & before saving. This object is in updatedObjects only. Why can this method return "bad" object? (Moreover, during updates this object is affected almost each update. And only after some passes becomes "bad" one). P.S.: I use RestKit to manage CoreData. UPDATED: The exception was got, when I did smth. like this: for (PRBattle *battle in [self.controller fetchedObjects) { switch (battle.statusScalar) { case ... default: [battle willAccessValueForKey:nil]; NSAssert1(NO, @"Unexpected battle status found: %@", battle); } } The exception is on line with -willAccessValueForKey:. Scalar status for battle is enum, that is bind to integer values 1..4. I've mentioned all possible values in switch's cases (above default:). And the last one has break;. So this one is possible only when battle.statusScalar returns non-enum value. Status scalar implementation in PRBattle: - (PRBattleStatuses)statusScalar { [self willAccessValueForKey:@"statusScalar"]; PRBattleStatuses result = (PRBattleStatuses)[self.status integerValue]; [self didAccessValueForKey:@"statusScalar"]; return result; } And battle.status has validation rules: - min-value: 1 - max-value: 4 - default: no value And the last thing - debug log: objc[4664]: EXCEPTIONS: throwing 0x7d33f80 (object 0xe67d2a0, a _NSCoreDataException) objc[4664]: EXCEPTIONS: searching through frame [ip=0x97b401 sp=0xbfffd9b0] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: catch(id) objc[4664]: EXCEPTIONS: unwinding through frame [ip=0x97b401 sp=0xbfffd9b0] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: handling exception 0x7d33f60 at 0x97b79f objc[4664]: EXCEPTIONS: rethrowing current exception objc[4664]: EXCEPTIONS: searching through frame [ip=0x97b911 sp=0xbfffd9b0] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: searching through frame [ip=0x9ac8b7 sp=0xbfffdc20] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: searching through frame [ip=0x97ee80 sp=0xbfffdc40] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: searching through frame [ip=0x361d0 sp=0xbfffdc70] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: searching through frame [ip=0xa701d8 sp=0xbfffde10] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: catch(id) objc[4664]: EXCEPTIONS: unwinding through frame [ip=0x97b911 sp=0xbfffd9b0] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: finishing handler objc[4664]: EXCEPTIONS: searching through frame [ip=0x97b963 sp=0xbfffd9b0] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: searching through frame [ip=0x9ac8b7 sp=0xbfffdc20] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: searching through frame [ip=0x97ee80 sp=0xbfffdc40] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: searching through frame [ip=0x361d0 sp=0xbfffdc70] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: searching through frame [ip=0xa701d8 sp=0xbfffde10] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: catch(id) objc[4664]: EXCEPTIONS: unwinding through frame [ip=0x97b963 sp=0xbfffd9b0] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: unwinding through frame [ip=0x9ac8b7 sp=0xbfffdc20] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: unwinding through frame [ip=0x97ee80 sp=0xbfffdc40] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: unwinding through frame [ip=0x361d0 sp=0xbfffdc70] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: unwinding through frame [ip=0x3656f sp=0xbfffdc70] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: unwinding through frame [ip=0xa701d8 sp=0xbfffde10] for exception 0x7d33f60 objc[4664]: EXCEPTIONS: handling exception 0x7d33f60 at 0xa701f5 2012-11-07 13:37:55.463 TestApp[4664:fb03] CoreData: error: Serious application error. An exception was caught from the delegate of NSFetchedResultsController during a call to -controllerDidChangeContent:. CoreData could not fulfill a fault for '0x6d31650 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p10>' with userInfo { NSAffectedObjectsErrorKey = ( "<PRBattle: 0x6d30830> (entity: PRBattle; id: 0x6d31650 <x-coredata://882BD521-90CD-4682-B19A-000A4976E471/PRBattle/p10> ; data: <fault>)" ); }

  Read the article

• Please help to clean up my RoR development environment

  - by PeterWong

  I started RoR development a few months ago, and being new to Mac... Time flies and now I have a lot different ruby versions, rails versions and gems versions located everywhere......And currently I installed rvm and things got even worst, all things messed! And so I started want to clean all things and use rvm again! I want to uninstall all gems, all rails, and all ruby versions, except the system's default one (the very old one born with the mac). Or any other better solutions or suggestions!? Please help! there is some info that I think will be useful: which -a ruby /opt/local/bin/ruby /opt/local/bin/ruby /usr/local/bin/ruby /usr/bin/ruby /usr/local/bin/ruby which -a rails /usr/local/bin/rails /usr/bin/rails /usr/local/bin/rails which -a compass # simliar for rspec and many other gems /usr/local/bin/compass /usr/local/bin/compass gem list *** LOCAL GEMS *** abstract (1.0.0) actionmailer (3.0.3, 3.0.1, 3.0.0, 3.0.0.rc2, 2.3.9, 2.3.5, 2.3.4) actionpack (3.0.3, 3.0.1, 3.0.0, 3.0.0.rc2, 2.3.9, 2.3.5, 2.3.4) activemodel (3.0.3, 3.0.1, 3.0.0, 3.0.0.rc2) activerecord (3.0.3, 3.0.1, 3.0.0, 3.0.0.rc2, 2.3.9, 2.3.5, 2.3.4) activeresource (3.0.3, 3.0.1, 3.0.0, 3.0.0.rc2, 2.3.9, 2.3.5, 2.3.4) activesupport (3.0.3, 3.0.1, 3.0.0, 3.0.0.rc2, 2.3.9, 2.3.5, 2.3.4) addressable (2.2.2) arel (2.0.6, 1.0.1, 1.0.0.rc1) authlogic (2.1.6, 2.1.3) aws-s3 (0.6.2) base32 (0.1.2) block_helpers (0.3.3) bluecloth (2.0.9) bowline (0.9.4) bowline-bundler (0.0.4) bson (1.1.2) builder (2.1.2) bundler (1.0.2, 1.0.0) compass (0.10.6) crack (0.1.7) devise (1.1.3) diff-lcs (1.1.2) differ (0.1.1) dynamic_form (1.1.3) engineyard (1.3.1) engineyard-serverside-adapter (1.3.3) erubis (2.6.6) escape (0.0.4) extlib (0.9.15) facebooker (1.0.75) faker (0.3.1) faraday (0.5.3, 0.5.2) fast_gettext (0.5.10, 0.4.17) fastercsv (1.5.3) fastthread (1.0.7) ffi (0.6.3) formatize (1.0.1) formtastic (1.1.0, 1.0.1) gemcutter (0.5.0) gettext (2.1.0) git (1.2.5) gosu (0.7.25 universal-darwin) haml (3.0.24, 3.0.23, 3.0.22, 3.0.21, 3.0.18) haml-rails (0.3.4) heroku (1.10.13, 1.9.13) highline (1.5.2) hirb (0.3.4, 0.3.3) hpricot (0.8.2) i18n (0.5.0, 0.4.2, 0.4.1, 0.3.7) jeweler (1.4.0) json (1.4.6) json_pure (1.4.3) linkedin (0.1.8) locale (2.0.5) mail (2.2.12, 2.2.11, 2.2.10, 2.2.9, 2.2.7, 2.2.6.1) memcache-client (1.8.5) meta_search (0.9.8, 0.9.7.2, 0.9.7.1, 0.9.6, 0.9.4) mime-types (1.16) mongo (1.1.2) mongoid (2.0.0.beta.20) multi_json (0.0.5) multipart-post (1.0.1) mysql (2.8.1) mysql2 (0.2.6, 0.2.4, 0.2.3) net-ldap (0.1.1) nice-ffi (0.4) nokogiri (1.4.4, 1.4.2) oa-basic (0.1.6) oa-core (0.1.6) oa-enterprise (0.1.6) oa-oauth (0.1.6) oa-openid (0.1.6) oauth (0.4.4, 0.4.3, 0.4.1) oauth-plugin (0.4.0.pre1) oauth2 (0.1.0) omniauth (0.1.6) paperclip (2.3.6, 2.3.4, 2.3.1.1) passenger (2.2.12) polyglot (0.3.1) pyu-ruby-sasl (0.0.3.2) querybuilder (0.9.2, 0.5.9) rack (1.2.1, 1.1.0, 1.0.1) rack-cache (0.5.3) rack-cache-purge (0.0.2, 0.0.1) rack-mount (0.6.13) rack-openid (1.2.0) rack-test (0.5.6, 0.5.4) railroady (0.11.2) rails (3.0.3, 3.0.1, 3.0.0, 3.0.0.rc2, 2.3.9, 2.3.5, 2.3.4) railties (3.0.3, 3.0.1, 3.0.0, 3.0.0.rc2) rake (0.8.7) RedCloth (3.0.4) rest-client (1.6.1) roxml (3.1.5) rscribd (1.2.0) rspec (2.3.0, 2.2.0, 2.1.0, 2.0.1) rspec-core (2.3.0, 2.2.1, 2.1.0, 2.0.1) rspec-expectations (2.3.0, 2.2.0, 2.1.0, 2.0.1) rspec-mocks (2.3.0, 2.2.0, 2.1.0, 2.0.1) rspec-rails (2.3.0, 2.2.0, 2.1.0, 2.0.1) ruby-hmac (0.4.0) ruby-mysql (2.9.3) ruby-ole (1.2.10.1) ruby-openid (2.1.8) ruby-openid-apps-discovery (1.2.0) ruby-recaptcha (1.0.2, 1.0.0) ruby-sdl-ffi (0.3) ruby-termios (0.9.6) ruby_parser (2.0.5) rubyforge (2.0.4) rubygame (2.6.4) rubygems-update (1.3.7) rubyless (0.7.0, 0.6.0, 0.3.5) rubyntlm (0.1.1) rubyzip2 (2.0.1) scribd_fu (2.0.6) searchlogic (2.4.27, 2.4.23) sequel (3.16.0, 3.15.0, 3.13.0) sexp_processor (3.0.5) shoulda (2.11.3) sinatra (1.0) slim (0.8.0) slim-rails (0.1.2) spreadsheet (0.6.4.1) sqlite3-ruby (1.3.2, 1.3.1) ssl_requirement (0.1.0) subdomain-fu (1.0.0.beta2, 0.5.4) supermodel (0.1.4) syntax (1.0.0) taps (0.3.13, 0.3.11) templater (1.0.0) temple (0.1.6) text-format (1.0.0) text-hyphen (1.0.0) thor (0.14.6, 0.14.4, 0.14.3, 0.14.1, 0.14.0) tilt (1.1) treetop (1.4.9, 1.4.8) tzinfo (0.3.23) uuidtools (2.1.1, 2.0.0) validates_timeliness (3.0.0.beta.4, 2.3.1) warden (0.10.7) will_paginate (3.0.pre2, 2.3.15, 2.3.14) xml-simple (1.0.12) ya2yaml (0.30) yajl-ruby (0.7.8, 0.7.7) yamltest (0.7.0) zena (0.16.9, 0.16.8) ====== I have ran sudo rvm implode and sudo rm -rf ~/.rvm, so no rvm now. gem env RubyGems Environment: - RUBYGEMS VERSION: 1.3.7 - RUBY VERSION: 1.8.7 (2009-06-12 patchlevel 174) [i686-darwin10.2.0] - INSTALLATION DIRECTORY: /usr/local/lib/ruby/gems/1.8 - RUBY EXECUTABLE: /usr/local/bin/ruby - EXECUTABLE DIRECTORY: /usr/local/bin - RUBYGEMS PLATFORMS: - ruby - x86-darwin-10 - GEM PATHS: - /usr/local/lib/ruby/gems/1.8 - /Users/peter/.gem/ruby/1.8 - GEM CONFIGURATION: - :update_sources => true - :verbose => true - :benchmark => false - :backtrace => false - :bulk_threshold => 1000 - :sources => ["http://rubygems.org/", "http://gems.github.com"] - REMOTE SOURCES: - http://rubygems.org/ - http://gems.github.com === ls -al /usr/local/lib/ total 5704 drwxr-xr-x 7 root wheel 238 Jun 1 2010 . drwxr-xr-x 9 root wheel 306 Dec 15 16:20 .. -rw-r--r-- 1 root wheel 1717208 Jun 1 2010 libruby-static.a -rwxr-xr-x 1 root wheel 1191880 Jun 1 2010 libruby.1.8.7.dylib lrwxrwxrwx 1 root wheel 19 Jun 1 2010 libruby.1.8.dylib -> libruby.1.8.7.dylib lrwxrwxrwx 1 root wheel 19 Jun 1 2010 libruby.dylib -> libruby.1.8.7.dylib drwxr-xr-x 6 root wheel 204 Jun 1 2010 ruby

  Read the article

• Delphi hook to redirect to different ip

  - by Chris

  What is the best way to redirect ANY browser to a different ip for specific sites? For example if the user will type www.facebook.com in any browser he will be redirected to 127.0.0.1. Also the same should happen if he will type 66.220.146.11. What I have until now is this: using the winpkfilter I am able to intercept all the traffic on port 80, with type(in or out), source ip, destination ip and packet. My problem is to modify somehow the packet so the browser will be redirected. This is the code that i have right now: program Pass; {$APPTYPE CONSOLE} uses SysUtils, Windows, Winsock, winpkf, iphlp; var iIndex, counter : DWORD; hFilt : THANDLE; Adapts : TCP_AdapterList; AdapterMode : ADAPTER_MODE; Buffer, ParsedBuffer : INTERMEDIATE_BUFFER; ReadRequest : ETH_REQUEST; hEvent : THANDLE; hAdapter : THANDLE; pEtherHeader : TEtherHeaderPtr; pIPHeader : TIPHeaderPtr; pTcpHeader : TTCPHeaderPtr; pUdpHeader : TUDPHeaderPtr; SourceIP, DestIP : TInAddr; thePacket : PChar; f : TextFile; SourceIpString, DestinationIpString : string; SourceName, DestinationName : string; function IPAddrToName(IPAddr : string) : string; var SockAddrIn : TSockAddrIn; HostEnt : PHostEnt; WSAData : TWSAData; begin WSAStartup($101, WSAData); SockAddrIn.sin_addr.s_addr := inet_addr(PChar(IPAddr)); HostEnt := gethostbyaddr(@SockAddrIn.sin_addr.S_addr, 4, AF_INET); if HostEnt < nil then begin result := StrPas(Hostent^.h_name) end else begin result := ''; end; end; procedure ReleaseInterface(); begin // Restore default mode AdapterMode.dwFlags := 0; AdapterMode.hAdapterHandle := hAdapter; SetAdapterMode(hFilt, @AdapterMode); // Set NULL event to release previously set event object SetPacketEvent(hFilt, hAdapter, 0); // Close Event if hEvent < 0 then CloseHandle(hEvent); // Close driver object CloseFilterDriver(hFilt); // Release NDISAPI FreeNDISAPI(); end; begin // Check the number of parameters if ParamCount() < 2 then begin Writeln('Command line syntax:'); Writeln(' PassThru.exe index num'); Writeln(' index - network interface index.'); Writeln(' num - number or packets to filter'); Writeln('You can use ListAdapters to determine correct index.'); Exit; end; // Initialize NDISAPI InitNDISAPI(); // Create driver object hFilt := OpenFilterDriver('NDISRD'); if IsDriverLoaded(hFilt) then begin // Get parameters from command line iIndex := StrToInt(ParamStr(1)); counter := StrToInt(ParamStr(2)); // Set exit procedure ExitProcessProc := ReleaseInterface; // Get TCP/IP bound interfaces GetTcpipBoundAdaptersInfo(hFilt, @Adapts); // Check paramer values if iIndex > Adapts.m_nAdapterCount then begin Writeln('There is no network interface with such index on this system.'); Exit; end; hAdapter := Adapts.m_nAdapterHandle[iIndex]; AdapterMode.dwFlags := MSTCP_FLAG_SENT_TUNNEL or MSTCP_FLAG_RECV_TUNNEL; AdapterMode.hAdapterHandle := hAdapter; // Create notification event hEvent := CreateEvent(nil, TRUE, FALSE, nil); if hEvent <> 0 then if SetPacketEvent(hFilt, hAdapter, hEvent) <> 0 then begin // Initialize request ReadRequest.EthPacket.Buffer := @Buffer; ReadRequest.hAdapterHandle := hAdapter; SetAdapterMode(hFilt, @AdapterMode); counter := 0; //while counter <> 0 do while true do begin WaitForSingleObject(hEvent, INFINITE); while ReadPacket(hFilt, @ReadRequest) <> 0 do begin //dec(counter); pEtherHeader := TEtherHeaderPtr(@Buffer.m_IBuffer); if ntohs(pEtherHeader.h_proto) = ETH_P_IP then begin pIPHeader := TIPHeaderPtr(Integer(pEtherHeader) + SizeOf(TEtherHeader)); SourceIP.S_addr := pIPHeader.SourceIp; DestIP.S_addr := pIPHeader.DestIp; if pIPHeader.Protocol = IPPROTO_TCP then begin pTcpHeader := TTCPHeaderPtr(Integer(pIPHeader) + (pIPHeader.VerLen and $F) * 4); if (pTcpHeader.SourcePort = htons(80)) or (pTcpHeader.DestPort = htons(80)) then begin inc(counter); if Buffer.m_dwDeviceFlags = PACKET_FLAG_ON_SEND then Writeln(counter, ') - MSTCP --> Interface') else Writeln(counter, ') - Interface --> MSTCP'); Writeln(' Packet size = ', Buffer.m_Length); Writeln(Format(' IP %.3u.%.3u.%.3u.%.3u --> %.3u.%.3u.%.3u.%.3u PROTOCOL: %u', [byte(SourceIP.S_un_b.s_b1), byte(SourceIP.S_un_b.s_b2), byte(SourceIP.S_un_b.s_b3), byte(SourceIP.S_un_b.s_b4), byte(DestIP.S_un_b.s_b1), byte(DestIP.S_un_b.s_b2), byte(DestIP.S_un_b.s_b3), byte(DestIP.S_un_b.s_b4), byte(pIPHeader.Protocol)] )); Writeln(Format(' TCP SRC PORT: %d DST PORT: %d', [ntohs(pTcpHeader.SourcePort), ntohs(pTcpHeader.DestPort)])); //get the data thePacket := pchar(pEtherHeader) + (sizeof(TEtherHeaderPtr) + pIpHeader.VerLen * 4 + pTcpHeader.Offset * 4); { SourceIpString := IntToStr(byte(SourceIP.S_un_b.s_b1)) + '.' + IntToStr(byte(SourceIP.S_un_b.s_b2)) + '.' + IntToStr(byte(SourceIP.S_un_b.s_b3)) + '.' + IntToStr(byte(SourceIP.S_un_b.s_b4)); DestinationIpString := IntToStr(byte(DestIP.S_un_b.s_b1)) + '.' + IntToStr(byte(DestIP.S_un_b.s_b2)) + '.' + IntToStr(byte(DestIP.S_un_b.s_b3)) + '.' + IntToStr(byte(DestIP.S_un_b.s_b4)); } end; end; end; // if ntohs(pEtherHeader.h_proto) = ETH_P_RARP then // Writeln(' Reverse Addr Res packet'); // if ntohs(pEtherHeader.h_proto) = ETH_P_ARP then // Writeln(' Address Resolution packet'); //Writeln('__'); if Buffer.m_dwDeviceFlags = PACKET_FLAG_ON_SEND then // Place packet on the network interface SendPacketToAdapter(hFilt, @ReadRequest) else // Indicate packet to MSTCP SendPacketToMstcp(hFilt, @ReadRequest); { if counter = 0 then begin Writeln('Filtering complete'); readln; break; end; } end; ResetEvent(hEvent); end; end; end; end.

  Read the article

• Codeigniter: Using URIs with forms

  - by Kevin Brown

  I'm using URIs to direct a function in a library: $id = $this->CI->session->userdata('id'); $URI = $this->CI->uri->uri_string(); $new = "new"; if(strpos($URI, $new) === FALSE){ $method = "update"; } elseif(strpos($URI, $new) !== FALSE){ $method = "create"; } So I have two if statements directing what information to if ($method === 'update') { // Modify form, first load $this->CI->db->from('be_survey'); $this->CI->db->where('user_id' , $id); $survey = $this->CI->db->get(); $user = array_merge($user->row_array(),$survey->row_array()); $this->CI->validation->set_default_value($user); // Display page $data['user'] = $user; } $this->CI->validation->set_rules($rules); if ( $this->CI->validation->run() === FALSE ) { // Output any errors $this->CI->validation->output_errors(); } else { // Submit form $this->_submit($method); } Submit function: function _submit($method) { //Submit and Update for current User $id = $this->CI->session->userdata('id'); $this->CI->db->select('users.id, users.username, users.email, profiles.firstname, profiles.manager_id'); $this->CI->db->from('be_users' . " users"); $this->CI->db->join('be_user_profiles' . " profiles",'users.id=profiles.user_id'); $this->CI->db->having('id', $id); $email_data['user'] = $this->CI->db->get(); $email_data['user'] = $email_data['user']->row(); $manager_id = $email_data['user']->manager_id; $this->CI->db->select('firstname','email')->from('be_user_profiles')->where('user_id', $manager_id); $email_data['manager'] = $this->CI->db->get(); $email_data['manager'] = $email_data['manager']->row(); // Fetch what they entered in the form for($i=1;$i<18;$i++){ $survey["a_".$i]= $this->CI->input->post('a_'.$i); } for($i=1;$i<15;$i++){ $survey["b_".$i]= $this->CI->input->post('b_'.$i); } for($i=1;$i<12;$i++){ $survey["c_".$i]= $this->CI->input->post('c_'.$i); } $profile['firstname'] = $this->CI->input->post('firstname'); $profile['lastname'] = $this->CI->input->post('lastname'); $profile['test_date'] = date ("Y-m-d H:i:s"); $profile['company_name'] = $this->CI->input->post('company_name'); $profile['company_address'] = $this->CI->input->post('company_address'); $profile['company_city'] = $this->CI->input->post('company_city'); $profile['company_phone'] = $this->CI->input->post('company_phone'); $profile['company_state'] = $this->CI->input->post('company_state'); $profile['company_zip'] = $this->CI->input->post('company_zip'); $profile['job_title'] = $this->CI->input->post('job_title'); $profile['job_type'] = $this->CI->input->post('job_type'); $profile['job_time'] = $this->CI->input->post('job_time'); $profile['department'] = $this->CI->input->post('department'); $profile['vision'] = $this->CI->input->post('vision'); $profile['height'] = $this->CI->input->post('height'); $profile['weight'] = $this->CI->input->post('weight'); $profile['hand_dominance'] = $this->CI->input->post('hand_dominance'); $profile['areas_of_fatigue'] = $this->CI->input->post('areas_of_fatigue'); $profile['job_description'] = $this->CI->input->post('job_description'); $profile['injury_review'] = $this->CI->input->post('injury_review'); $profile['job_positive'] = $this->CI->input->post('job_positive'); $profile['risk_factors'] = $this->CI->input->post('risk_factors'); $profile['job_improvement_short'] = $this->CI->input->post('job_improvement_short'); $profile['job_improvement_long'] = $this->CI->input->post('job_improvement_long'); if ($method == "update") { //Begin db transmission $this->CI->db->trans_begin(); $this->CI->home_model->update('Survey',$survey, array('user_id' => $id)); $this->CI->db->update('be_user_profiles',$profile, array('user_id' => $id)); if ($this->CI->db->trans_status() === FALSE) { flashMsg('error','There was a problem entering your test! Please contact an administrator.'); redirect('survey','location'); } else { //Get credits of user and subtract 1 $this->CI->db->set('credits', 'credits -1', FALSE); $this->CI->db->update('be_user_profiles',$profile, array('user_id' => $manager_id)); //Mark the form completed. $this->CI->db->set('test_complete', '1'); $this->CI->db->where('user_id', $id)->update('be_user_profiles'); // Stuff worked... $this->CI->db->trans_commit(); //Get Manager Information $this->CI->db->select('users.id, users.username, users.email, profiles.firstname'); $this->CI->db->from('be_users' . " users"); $this->CI->db->join('be_user_profiles' . " profiles",'users.id=profiles.user_id'); $this->CI->db->having('id', $email_data['user']->manager_id); $email_data['manager'] = $this->CI->db->get(); $email_data['manager'] = $email_data['manager']->row(); //Email User $this->CI->load->library('User_email'); $data_user = array( 'firstname'=>$email_data['user']->firstname, 'email'=> $email_data['user']->email, 'user_completed'=>$email_data['user']->firstname, 'site_name'=>$this->CI->preference->item('site_name'), 'site_url'=>base_url() ); //Email Manager $data_manager = array( 'firstname'=>$email_data['manager']->firstname, 'email'=> $email_data['manager']->email, 'user_completed'=>$email_data['user']->firstname, 'site_name'=>$this->CI->preference->item('site_name'), 'site_url'=>base_url() ); $this->CI->user_email->send($email_data['manager']->email,'Completed the Assessment Tool','public/email_manager_complete',$data_manager); $this->CI->user_email->send($email_data['user']->email,'Completed the Assessment Tool','public/email_user_complete',$data_user); flashMsg('success','You finished the assessment successfully!'); redirect('home','location'); } } //Create New User elseif ($method == "create") { // Build $profile['user_id'] = $id; $profile['manager_id'] = $manager_id; $profile['test_complete'] = '1'; $survey['user_id'] = $id; $this->CI->db->trans_begin(); // Add user_profile details to DB $this->CI->db->insert('be_user_profiles',$profile); $this->CI->db->insert('be_survey',$survey); if ($this->CI->db->trans_status() === FALSE) { // Registration failed $this->CI->db->trans_rollback(); flashMsg('error',$this->CI->lang->line('userlib_registration_failed')); redirect('auth/register','location'); } else { // User registered $this->CI->db->trans_commit(); flashMsg('success',$this->CI->lang->line('userlib_registration_success')); redirect($this->CI->config->item('userlib_action_register'),'location'); } } } The submit function is similar, updating the db if $method == "update", and inserting if the method == "create". The problem is, when the form is submitted, it doesn't take into account the url b/c the form submits to the function "survey", which passes data to the lib function, so things are always updated, never created. *How can I pass $method to the _submit() function correctly?!*

  Read the article

• Sorting and Re-arranging List of HashMaps

  - by HonorGod

  I have a List which is straight forward representation of a database table. I am trying to sort and apply some magic after the data is loaded into List of HashMaps. In my case this is the only hard and fast way of doing it becoz I have a rules engine that actually updates the values in the HashMap after several computations. Here is a sample data representation of the HashMap (List of HashMap) - {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=21, toDate=Tue Mar 23 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=11, toDate=Wed Mar 17 10:54:12 EDT 2010, actionId=456} {fromDate=Sat Mar 20 10:54:12 EDT 2010, eventId=20, toDate=Thu Apr 01 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 24 10:54:12 EDT 2010, eventId=22, toDate=Sat Mar 27 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=11, toDate=Fri Mar 26 10:54:12 EDT 2010, actionId=1234} {fromDate=Sat Mar 20 10:54:12 EDT 2010, eventId=11, toDate=Wed Mar 31 10:54:12 EDT 2010, actionId=1234} {fromDate=Mon Mar 15 10:54:12 EDT 2010, eventId=12, toDate=Wed Mar 17 10:54:12 EDT 2010, actionId=567} I am trying to achieve couple of things - 1) Sort the list by actionId and eventId after which the data would look like - {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=11, toDate=Wed Mar 17 10:54:12 EDT 2010, actionId=456} {fromDate=Mon Mar 15 10:54:12 EDT 2010, eventId=12, toDate=Wed Mar 17 10:54:12 EDT 2010, actionId=567} {fromDate=Wed Mar 24 10:54:12 EDT 2010, eventId=22, toDate=Sat Mar 27 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=21, toDate=Tue Mar 23 10:54:12 EDT 2010, actionId=1234} {fromDate=Sat Mar 20 10:54:12 EDT 2010, eventId=20, toDate=Thu Apr 01 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=11, toDate=Fri Mar 26 10:54:12 EDT 2010, actionId=1234} {fromDate=Sat Mar 20 10:54:12 EDT 2010, eventId=11, toDate=Wed Mar 31 10:54:12 EDT 2010, actionId=1234} 2) If we group the above list by actionId they would be resolved into 3 groups - actionId=1234, actionId=567 and actionId=456. Now here is my question - For each group having the same eventId, I need to update the records so that they have wider fromDate to toDate. Meaning, if you consider the last two rows they have same actionId = 1234 and same eventId = 11. Now we can to pick the least fromDate from those 2 records which is Wed Mar 17 10:54:12 and farther toDate which is Wed Mar 31 10:54:12 and update those 2 record's fromDate and toDate to Wed Mar 17 10:54:12 and Wed Mar 31 10:54:12 respectively. Any ideas? PS: I already have some pseudo code to start with. import java.util.ArrayList; import java.util.Calendar; import java.util.Collections; import java.util.Comparator; import java.util.Date; import java.util.HashMap; import java.util.List; import org.apache.commons.lang.builder.CompareToBuilder; public class Tester { boolean ascending = true ; boolean sortInstrumentIdAsc = true ; boolean sortEventTypeIdAsc = true ; public static void main(String args[]) { Tester tester = new Tester() ; tester.printValues() ; } public void printValues () { List<HashMap<String,Object>> list = new ArrayList<HashMap<String,Object>>() ; HashMap<String,Object> map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(21)) ; map.put("fromDate", getDate(1) ) ; map.put("toDate", getDate(7) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(456)) ; map.put("eventId", new Integer(11)) ; map.put("fromDate", getDate(1)) ; map.put("toDate", getDate(1) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(20)) ; map.put("fromDate", getDate(4) ) ; map.put("toDate", getDate(16) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(22)) ; map.put("fromDate",getDate(8) ) ; map.put("toDate", getDate(11)) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(11)) ; map.put("fromDate",getDate(1) ) ; map.put("toDate", getDate(10) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(11)) ; map.put("fromDate",getDate(4) ) ; map.put("toDate", getDate(15) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(567)) ; map.put("eventId", new Integer(12)) ; map.put("fromDate", getDate(-1) ) ; map.put("toDate",getDate(1)) ; list.add(map); System.out.println("\n Before Sorting \n "); for(int j = 0 ; j < list.size() ; j ++ ) System.out.println(list.get(j)); Collections.sort ( list , new HashMapComparator2 () ) ; System.out.println("\n After Sorting \n "); for(int j = 0 ; j < list.size() ; j ++ ) System.out.println(list.get(j)); } public static Date getDate(int days) { Calendar cal = Calendar.getInstance(); cal.setTime(new Date()); cal.add(Calendar.DATE, days); return cal.getTime() ; } public class HashMapComparator2 implements Comparator { public int compare ( Object object1 , Object object2 ) { if ( ascending == true ) { return new CompareToBuilder() .append(( ( HashMap ) object1 ).get ( "actionId" ), ( ( HashMap ) object2 ).get ( "actionId" )) .append(( ( HashMap ) object2 ).get ( "eventId" ), ( ( HashMap ) object1 ).get ( "eventId" )) .toComparison(); } else { return new CompareToBuilder() .append(( ( HashMap ) object2 ).get ( "actionId" ), ( ( HashMap ) object1 ).get ( "actionId" )) .append(( ( HashMap ) object2 ).get ( "eventId" ), ( ( HashMap ) object1 ).get ( "eventId" )) .toComparison(); } } } }

  Read the article

• What is correct HTTP status code when redirecting to a login page?

  - by PHP_Jedi

  When a user is not logged in and tries to access an page that requires login, what is the correct HTTP status code for a redirect to the login page? I don't feel that any of the 3xx fit that description. 10.3.1 300 Multiple Choices The requested resource corresponds to any one of a set of representations, each with its own specific location, and agent- driven negotiation information (section 12) is being provided so that the user (or user agent) can select a preferred representation and redirect its request to that location. Unless it was a HEAD request, the response SHOULD include an entity containing a list of resource characteristics and location(s) from which the user or user agent can choose the one most appropriate. The entity format is specified by the media type given in the Content- Type header field. Depending upon the format and the capabilities of the user agent, selection of the most appropriate choice MAY be performed automatically. However, this specification does not define any standard for such automatic selection. If the server has a preferred choice of representation, it SHOULD include the specific URI for that representation in the Location field; user agents MAY use the Location field value for automatic redirection. This response is cacheable unless indicated otherwise. 10.3.2 301 Moved Permanently The requested resource has been assigned a new permanent URI and any future references to this resource SHOULD use one of the returned URIs. Clients with link editing capabilities ought to automatically re-link references to the Request-URI to one or more of the new references returned by the server, where possible. This response is cacheable unless indicated otherwise. The new permanent URI SHOULD be given by the Location field in the response. Unless the request method was HEAD, the entity of the response SHOULD contain a short hypertext note with a hyperlink to the new URI(s). If the 301 status code is received in response to a request other than GET or HEAD, the user agent MUST NOT automatically redirect the request unless it can be confirmed by the user, since this might change the conditions under which the request was issued. Note: When automatically redirecting a POST request after receiving a 301 status code, some existing HTTP/1.0 user agents will erroneously change it into a GET request. 10.3.3 302 Found The requested resource resides temporarily under a different URI. Since the redirection might be altered on occasion, the client SHOULD continue to use the Request-URI for future requests. This response is only cacheable if indicated by a Cache-Control or Expires header field. The temporary URI SHOULD be given by the Location field in the response. Unless the request method was HEAD, the entity of the response SHOULD contain a short hypertext note with a hyperlink to the new URI(s). If the 302 status code is received in response to a request other than GET or HEAD, the user agent MUST NOT automatically redirect the request unless it can be confirmed by the user, since this might change the conditions under which the request was issued. Note: RFC 1945 and RFC 2068 specify that the client is not allowed to change the method on the redirected request. However, most existing user agent implementations treat 302 as if it were a 303 response, performing a GET on the Location field-value regardless of the original request method. The status codes 303 and 307 have been added for servers that wish to make unambiguously clear which kind of reaction is expected of the client. 10.3.4 303 See Other The response to the request can be found under a different URI and SHOULD be retrieved using a GET method on that resource. This method exists primarily to allow the output of a POST-activated script to redirect the user agent to a selected resource. The new URI is not a substitute reference for the originally requested resource. The 303 response MUST NOT be cached, but the response to the second (redirected) request might be cacheable. The different URI SHOULD be given by the Location field in the response. Unless the request method was HEAD, the entity of the response SHOULD contain a short hypertext note with a hyperlink to the new URI(s). Note: Many pre-HTTP/1.1 user agents do not understand the 303 status. When interoperability with such clients is a concern, the 302 status code may be used instead, since most user agents react to a 302 response as described here for 303. 10.3.5 304 Not Modified If the client has performed a conditional GET request and access is allowed, but the document has not been modified, the server SHOULD respond with this status code. The 304 response MUST NOT contain a message-body, and thus is always terminated by the first empty line after the header fields. The response MUST include the following header fields: - Date, unless its omission is required by section 14.18.1 If a clockless origin server obeys these rules, and proxies and clients add their own Date to any response received without one (as already specified by [RFC 2068], section 14.19), caches will operate correctly. - ETag and/or Content-Location, if the header would have been sent in a 200 response to the same request - Expires, Cache-Control, and/or Vary, if the field-value might differ from that sent in any previous response for the same variant If the conditional GET used a strong cache validator (see section 13.3.3), the response SHOULD NOT include other entity-headers. Otherwise (i.e., the conditional GET used a weak validator), the response MUST NOT include other entity-headers; this prevents inconsistencies between cached entity-bodies and updated headers. If a 304 response indicates an entity not currently cached, then the cache MUST disregard the response and repeat the request without the conditional. If a cache uses a received 304 response to update a cache entry, the cache MUST update the entry to reflect any new field values given in the response. 10.3.6 305 Use Proxy The requested resource MUST be accessed through the proxy given by the Location field. The Location field gives the URI of the proxy. The recipient is expected to repeat this single request via the proxy. 305 responses MUST only be generated by origin servers. Note: RFC 2068 was not clear that 305 was intended to redirect a single request, and to be generated by origin servers only. Not observing these limitations has significant security consequences. 10.3.7 306 (Unused) The 306 status code was used in a previous version of the specification, is no longer used, and the code is reserved. 10.3.8 307 Temporary Redirect The requested resource resides temporarily under a different URI. Since the redirection MAY be altered on occasion, the client SHOULD continue to use the Request-URI for future requests. This response is only cacheable if indicated by a Cache-Control or Expires header field. The temporary URI SHOULD be given by the Location field in the response. Unless the request method was HEAD, the entity of the response SHOULD contain a short hypertext note with a hyperlink to the new URI(s) , since many pre-HTTP/1.1 user agents do not understand the 307 status. Therefore, the note SHOULD contain the information necessary for a user to repeat the original request on the new URI. If the 307 status code is received in response to a request other than GET or HEAD, the user agent MUST NOT automatically redirect the request unless it can be confirmed by the user, since this might change the conditions under which the request was issued. I'm using 302 for now, until I find THE correct answer.

  Read the article

• How to customize and reuse a DataGridColumnHeader style?

  - by instcode

  Hi all, I'm trying to customize the column headers of a DataGrid to show sub-column headers as in the following screenshot: I've made a style for 2 sub-column as in the following XAML: <UserControl xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:data="clr-namespace:System.Windows.Controls;assembly=System.Windows.Controls.Data" xmlns:primitives="clr-namespace:System.Windows.Controls.Primitives;assembly=System.Windows.Controls.Data" xmlns:sl="clr-namespace:UI" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" x:Class="UI.ColumnHeaderGrid" mc:Ignorable="d"> <UserControl.Resources> <Style x:Key="SplitColumnHeaderStyle" TargetType="primitives:DataGridColumnHeader"> <Setter Property="Foreground" Value="#FF000000"/> <Setter Property="HorizontalContentAlignment" Value="Center"/> <Setter Property="VerticalContentAlignment" Value="Center"/> <Setter Property="IsTabStop" Value="False"/> <Setter Property="SeparatorBrush" Value="#FFC9CACA"/> <Setter Property="Padding" Value="4"/> <Setter Property="Template"> <Setter.Value> <ControlTemplate TargetType="primitives:DataGridColumnHeader"> <Grid x:Name="Root"> <Grid.ColumnDefinitions> <ColumnDefinition/> <ColumnDefinition Width="Auto"/> </Grid.ColumnDefinitions> <Rectangle x:Name="BackgroundRectangle" Fill="#FF1F3B53" Stretch="Fill" Grid.ColumnSpan="2"/> <Rectangle x:Name="BackgroundGradient" Stretch="Fill" Grid.ColumnSpan="2"> <Rectangle.Fill> <LinearGradientBrush EndPoint=".7,1" StartPoint=".7,0"> <GradientStop Color="#FCFFFFFF" Offset="0.015"/> <GradientStop Color="#F7FFFFFF" Offset="0.375"/> <GradientStop Color="#E5FFFFFF" Offset="0.6"/> <GradientStop Color="#D1FFFFFF" Offset="1"/> </LinearGradientBrush> </Rectangle.Fill> </Rectangle> <Grid> <Grid.ColumnDefinitions> <ColumnDefinition/> <ColumnDefinition Width="1"/> <ColumnDefinition/> </Grid.ColumnDefinitions> <Grid.RowDefinitions> <RowDefinition/> <RowDefinition/> <RowDefinition/> </Grid.RowDefinitions> <TextBlock Grid.Row="0" Grid.ColumnSpan="3" Text="Headers" TextAlignment="Center"/> <Rectangle Grid.Row="1" Grid.ColumnSpan="3" Fill="{TemplateBinding SeparatorBrush}" Height="1"/> <TextBlock Grid.Row="2" Grid.Column="0" Text="Header 1" TextAlignment="Center"/> <Rectangle Grid.Row="2" Grid.Column="1" Fill="{TemplateBinding SeparatorBrush}" Width="1"/> <TextBlock Grid.Row="2" Grid.Column="2" Text="Header 2" TextAlignment="Center"/> <Path x:Name="SortIcon" Grid.Column="2" Fill="#FF444444" Stretch="Uniform" HorizontalAlignment="Left" Margin="4,0,0,0" VerticalAlignment="Center" Width="8" Opacity="0" RenderTransformOrigin=".5,.5" Data="F1 M -5.215,6.099L 5.215,6.099L 0,0L -5.215,6.099 Z "/> </Grid> <Rectangle x:Name="VerticalSeparator" Fill="{TemplateBinding SeparatorBrush}" VerticalAlignment="Stretch" Width="1" Visibility="{TemplateBinding SeparatorVisibility}" Grid.Column="1"/> </Grid> </ControlTemplate> </Setter.Value> </Setter> </Style> </UserControl.Resources> <data:DataGrid x:Name="LayoutRoot"> <data:DataGrid.Columns> <data:DataGridTemplateColumn HeaderStyle="{StaticResource SplitColumnHeaderStyle}"> <data:DataGridTemplateColumn.CellTemplate> <DataTemplate> <Grid> <Grid.ColumnDefinitions> <ColumnDefinition/> <ColumnDefinition/> </Grid.ColumnDefinitions> <Border Grid.Column="0" BorderBrush="#FFC9CACA" BorderThickness="0,0,0,0"> <TextBlock Grid.Column="0" Text="{Binding GridData.Column1}"/> </Border> <Border Grid.Column="1" BorderBrush="#FFC9CACA" BorderThickness="1,0,0,0"> <TextBlock Grid.Column="0" Text="{Binding GridData.Column2}"/> </Border> </Grid> </DataTemplate> </data:DataGridTemplateColumn.CellTemplate> </data:DataGridTemplateColumn> </data:DataGrid.Columns> </data:DataGrid> Now I want to reuse & extend this style to support 2-6 sub-column headers but I don't know if there is a way to do this, like ContentPresenter "overriding": <Style x:Key="SplitColumnHeaderStyle" TargetType="primitives:DataGridColumnHeader"> <Setter property="Template"> <Setter.Value> ... <ContentPresenter Content="{TemplateBinding Content}".../> ... </Setter.Value> </Setter> </Style> <Style x:Key="TwoSubColumnHeaderStyle" BasedOn="SplitColumnHeaderStyle"> <Setter property="Content"> <Setter.Value> <Grid 2x2.../> </Setter.Value> </Setter> </Style> <Style x:Key="ThreeSubColumnHeaderStyle" BasedOn="SplitColumnHeaderStyle"> <Setter property="Content"> <Setter.Value> <Grid 2x3.../> </Setter.Value> </Setter> </Style> Anyway, please help me on these issues: Given the template above, how to support more sub-column headers without having to create new new new new template for each? Assume that the issue above is solved. How could I attach column names outside the styles? I see that some parts, properties & visualization rules in the XAML are just copies from the original Silverlight component's style, i.e. BackgroundGradient, BackgroundRectangle, VisualStateManager... They must be there in order to support default behaviors or effects but... does anyone know how to remove them, but keep all the default behaviors/effects? Please be specific because I'm just getting start with C# & Silverlight. Thanks.

  Read the article

• ASP.NET exception gives irrelevant stack trace on YSOD, very challenging!

  - by pootow

  Here is the YSOD: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Data.SqlClient.SqlException: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [SqlException (0x80131904): Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding.] System.Data.ProviderBase.DbConnectionPool.GetConnection(DbConnection owningObject) +428 System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) +65 System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) +117 System.Data.SqlClient.SqlConnection.Open() +122 ECommerce.PMethod.Sql.SqlConns.Open() +78 ECommerce.PMethod.Sql.SqlConns..ctor() +120 ECommerce.login.DatasInfo.Proc.UserCenter.IsLogin(String UserGUID, Int32 UserID) +49 ECommerce.login.Rules.Users.UserLogin.isLogin() +44 Config.isUserLogined() +5 Shopping_Shopping.Page_Load(Object sender, EventArgs e) +10 System.Web.Util.CalliHelper.EventArgFunctionCaller(IntPtr fp, Object o, Object t, EventArgs e) +14 System.Web.Util.CalliEventHandlerDelegateProxy.Callback(Object sender, EventArgs e) +35 System.Web.UI.Control.OnLoad(EventArgs e) +99 System.Web.UI.Control.LoadRecursive() +50 System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +627 [TypeInitializationException: The type initializer for 'ECommerce.ERP.DAL.DBConn' threw an exception.] ECommerce.ERP.DAL.DBConn.get_ConnString() +0 [ObjectDefinitionStoreException: Factory method 'System.String get_ConnString()' threw an Exception.] Spring.Objects.Factory.Support.SimpleInstantiationStrategy.Instantiate(RootObjectDefinition definition, String name, IObjectFactory factory, MethodInfo factoryMethod, Object[] arguments) +257 Spring.Objects.Factory.Support.ConstructorResolver.InstantiateUsingFactoryMethod(String name, RootObjectDefinition definition, Object[] arguments) +624 Spring.Objects.Factory.Support.AbstractAutowireCapableObjectFactory.InstantiateUsingFactoryMethod(String name, RootObjectDefinition definition, Object[] arguments) +60 Spring.Objects.Factory.Support.AbstractAutowireCapableObjectFactory.CreateObjectInstance(String objectName, RootObjectDefinition objectDefinition, Object[] arguments) +56 Spring.Objects.Factory.Support.AbstractAutowireCapableObjectFactory.InstantiateObject(String name, RootObjectDefinition definition, Object[] arguments, Boolean allowEagerCaching, Boolean suppressConfigure) +436 [ObjectCreationException: Error thrown by a dependency of object 'styleService' defined in 'assembly [ECommerce.Services.Impl, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null], resource [ECommerce.Services.Impl.AppContext.xml] line 56' : Initialization of object failed : Factory method 'System.String get_ConnString()' threw an Exception. while resolving 'constructor argument with name promotionservice' to 'promotionService' defined in 'assembly [ECommerce.Services.Impl, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null], resource [ECommerce.Services.Impl.AppContext.xml] line 31' while resolving 'constructor argument with name domainservice' to 'promotionDomainService' defined in 'assembly [ECommerce.Domain, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null], resource [ECommerce.Domain.AppContext.xml] line 20' while resolving 'constructor argument with name promotionrepos' to 'promotionRepos' defined in 'assembly [ECommerce.Data.AdoNet, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null], resource [ECommerce.Data.AdoNet.AppContext.xml] line 34' while resolving 'constructor argument with name connstr' to 'ECommerce.ERP.DAL.DBConn#389F399' defined in 'assembly [ECommerce.Data.AdoNet, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null], resource [ECommerce.Data.AdoNet.AppContext.xml] line 34'] Spring.Objects.Factory.Support.ObjectDefinitionValueResolver.ResolveReference(IObjectDefinition definition, String name, String argumentName, RuntimeObjectReference reference) +394 Spring.Objects.Factory.Support.ObjectDefinitionValueResolver.ResolvePropertyValue(String name, IObjectDefinition definition, String argumentName, Object argumentValue) +312 Spring.Objects.Factory.Support.ObjectDefinitionValueResolver.ResolveValueIfNecessary(String name, IObjectDefinition definition, String argumentName, Object argumentValue) +17 Spring.Objects.Factory.Support.ConstructorResolver.ResolveConstructorArguments(String objectName, RootObjectDefinition definition, ObjectWrapper wrapper, ConstructorArgumentValues cargs, ConstructorArgumentValues resolvedValues) +993 Spring.Objects.Factory.Support.ConstructorResolver.AutowireConstructor(String objectName, RootObjectDefinition rod, ConstructorInfo[] chosenCtors, Object[] explicitArgs) +171 Spring.Objects.Factory.Support.AbstractAutowireCapableObjectFactory.AutowireConstructor(String name, RootObjectDefinition definition, ConstructorInfo[] ctors, Object[] explicitArgs) +65 Spring.Objects.Factory.Support.AbstractAutowireCapableObjectFactory.CreateObjectInstance(String objectName, RootObjectDefinition objectDefinition, Object[] arguments) +161 Spring.Objects.Factory.Support.AbstractAutowireCapableObjectFactory.InstantiateObject(String name, RootObjectDefinition definition, Object[] arguments, Boolean allowEagerCaching, Boolean suppressConfigure) +636 Spring.Objects.Factory.Support.AbstractObjectFactory.CreateAndCacheSingletonInstance(String objectName, RootObjectDefinition objectDefinition, Object[] arguments) +174 Spring.Objects.Factory.Support.WebObjectFactory.CreateAndCacheSingletonInstance(String objectName, RootObjectDefinition objectDefinition, Object[] arguments) +150 Spring.Objects.Factory.Support.AbstractObjectFactory.GetObjectInternal(String name, Type requiredType, Object[] arguments, Boolean suppressConfigure) +990 Spring.Objects.Factory.Support.AbstractObjectFactory.GetObject(String name) +10 Spring.Context.Support.AbstractApplicationContext.GetObject(String name) +20 ECommerce.Common.ServiceLocator.GetService() +334 ECommerce.Mvc.Controllers.StylesController..ctor() +72 [TargetInvocationException: Exception has been thrown by the target of an invocation.] System.RuntimeTypeHandle.CreateInstance(RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean& canBeCached, RuntimeMethodHandle& ctor, Boolean& bNeedSecurityCheck) +0 System.RuntimeType.CreateInstanceSlow(Boolean publicOnly, Boolean fillCache) +86 System.RuntimeType.CreateInstanceImpl(Boolean publicOnly, Boolean skipVisibilityChecks, Boolean fillCache) +230 System.Activator.CreateInstance(Type type, Boolean nonPublic) +67 System.Web.Mvc.DefaultControllerFactory.GetControllerInstance(RequestContext requestContext, Type controllerType) +80 [InvalidOperationException: An error occurred when trying to create a controller of type 'ECommerce.Mvc.Controllers.StylesController'. Make sure that the controller has a parameterless public constructor.] System.Web.Mvc.DefaultControllerFactory.GetControllerInstance(RequestContext requestContext, Type controllerType) +190 System.Web.Mvc.DefaultControllerFactory.CreateController(RequestContext requestContext, String controllerName) +68 System.Web.Mvc.MvcHandler.ProcessRequestInit(HttpContextBase httpContext, IController& controller, IControllerFactory& factory) +118 System.Web.Mvc.MvcHandler.BeginProcessRequest(HttpContextBase httpContext, AsyncCallback callback, Object state) +46 System.Web.Mvc.MvcHandler.BeginProcessRequest(HttpContext httpContext, AsyncCallback callback, Object state) +63 System.Web.Mvc.MvcHandler.System.Web.IHttpAsyncHandler.BeginProcessRequest(HttpContext context, AsyncCallback cb, Object extraData) +13 System.Web.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +8677954 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +155 Version Information: Microsoft .NET Framework Version:2.0.50727.3082; ASP.NET Version:2.0.50727.3082 Question is: the first stack trace is irrelevant to others, what happened? Any ideas? Let me make this more clear: a MVC page uses the spring part trying to load a lazy-init service which constructor wants a connection string through a static property like this: <object id="promotionRepos" type="ECommerce.Data.AdoNet.Promotions.PromotionRepos, ECommerce.Data.AdoNet" lazy-init="true"> <constructor-arg name="provider"> <null /> </constructor-arg> <constructor-arg name="connStr"> <object type="ECommerce.ERP.DAL.DBConn, ECommerce.ERP.DAL" factory-method="get_ConnString" /> </constructor-arg> <property name="RefreshInterval" value="00:00:10" /> </object> the timeout part is some what irrelevent to all others. see this in the first exception: Shopping_Shopping.Page_Load(Object sender, EventArgs e) +10 it's another page at all. And also, ECommerce.PMethod.Sql.SqlConns.Open() uses its own connection string, not the one loaded by spring, it's different module from diffrent team. And I am sure the connection string is correct. And, this ysod cames up randomly. Sometimes nothing is wrong, and sometimes, it appears. I thought there could be something wrong with my database or the network/firewall, I will check it later, but now I want understand this tricky stack trace.

  Read the article

• Using jQuery validation plugin with tabbed navigation

  - by user3438917

  I have a tabbed navigation wizard, for which the first section needs to be validated before proceeding to the next tab. The validation should trigger when the user hits the "next" button. I am unable to get the validation to trigger though: <form id="target-group" novalidate="novalidate"> <div class="box"> <div class='box-header-main'><h2><img src="assets/img/list.png" /> Target Group Information</h2></div> <br /> <div class='box'> <div class='box-header-property'><h2><span data-bind="text:Name">New Target Group</span> | <i class='fa fa-file'></i></h2></div> <br /> <div class='row'> <div id='flight-wizard'> <div id='content' class='col-lg-12'> <div class='col-lg-12'> <div id='tabs'> <ul> <li id="targetgroup-info-tab"><a href='#tabs-1'><i class="fa fa-info-circle"></i>Target Group Info</a></li> <li id="zone-tab"><a href='#tabs-2'><i class="fa fa-map-marker"></i>Zones</a></li> </ul> <div id='tabs-1'> <div class='row'> <div class='col-xs-6'> <div class='form-group'> Name^* <input id="selectError0" name="name" class='form-control col-xs-12' data-bind="value: asdf" placeholder='Enter Name ...' /> </div> <form class='form-horizontal'> <div class='form-group'> Product(s)^* <div class='controls' id='products'> <select id='selectError3' class='form-control' data-bind="options:test, optionsText: 'Name', optionsValue : 'test', value: test, optionsCaption: 'Choose Product...'"></select> </div> </div> </form> </div> <!--RIGHT PANE--> <div class='col-xs-6'> <div class='form-group'> Platform^* <div class='controls'> <select id="selectError2" class='form-control' data-bind="options:test, optionsText: 'Name', optionsValue: 'test', value : test, optionsCaption: 'Choose Platform...'"></select> </div> </div> <form class='form-horizontal'> <div class='form-group'> AdTypes(s)^* <div class='controls' id='adtypes'> <select multiple="" id='adtypesselect' class='form-control' data-rel="chosen" data-bind="options:test, optionsText: 'Name', optionsValue : 'test', selectedOptions: test, optionsCaption: 'test...'"></select> </div> </div> </form> <button id="btn_cancel_large" class='btn btn-large btn-primary btn-round'><i class='fa fa-ban' /></i> Cancel</button> <button id="btn-next-large" class='btn btn-large btn-primary btn-round'>Next <i class='fa fa-arrow-circle-right'></i></button> </div> <!--end of right pane--> </div> </div> <div id='tabs-2'> <div class='row'> <div class='col-lg-12'> <div class='row'> <div class='col-lg-12'> <div id='zones_list' class='box-content'> <div id='add-new-targetgroupzone' class='add-new'><i class='fa fa-plus-circle'></i><a href='/#/inventory/targeting/' onclick="return false;">Add Zone</a></div> <table id="results" width="100%"> <thead> <tr> <th>Publisher</th> <th>Property</th> <th>Zone</th> <th>AdTypes</th> <th width='10%'>Quick&nbsp;Actions</th> </tr> </thead> </table> </div> </div> </div> </div> </div> <br /> <div class="btn_row"> <button id="btn_cancel_large2" class='btn btn-large btn-primary btn-round'><i class='fa fa-ban' /></i> Cancel</button> <button id="btn-submit-large" class='btn btn-large btn-primary btn-round'>Submit <i class='fa fa-arrow-circle-down'></i></button> </div> </div> </div> </div> </div> </div> </div> </div> </div> </form> <form id="zones-form" style="display: none;" novalidate="novalidate" class="slideup-form"> <div class="box"> <div class="box-header-panel"> <h2>Add Target Group Zone</h2> <div class="box-icon" id="zones-form-close"> <i class="fa fa-arrow-circle-down"></i> </div> </div> <div class="box-content clearfix"> <div class="box-content"> <table id="zones-list" width="100%"> <thead> <tr> <th>Publisher</th> <th>Property</th> <th>Zone</th> <th>AdTypes</th> <th width='10%'>Quick&nbsp;Actions</th> </tr> </thead> </table> </div> </div> </div> </div> </form> jQuery: $("#target-group").validate({ rules: { name: { required: true } }, messages: { name: "Name required", } }); $('#btn-next-large').click(function () { if ($('#target-group').valid()) $tabs.tabs('select', $(this).attr("rel")); });

  Read the article

• how to pass an id number string to this class

  - by Phil

  I'm very much a vb person, but have had to use this id number class in c#. I got it from http://www.codingsanity.com/idnumber.htm : using System; using System.Text.RegularExpressions; namespace Utilities.SouthAfrica { /// <summary> /// Represents a South African Identity Number. /// valid number = 7707215230080 /// invalid test number = 1234567891234 /// /// </summary> [Serializable()] public class IdentityNumber { #region Enumerations /// <summary> /// Indicates a gender. /// </summary> public enum PersonGender { Female = 0, Male = 5 } public enum PersonCitizenship { SouthAfrican = 0, Foreign = 1 } #endregion #region Declarations static Regex _expression; Match _match; const string _IDExpression = @"(?<Year>[0-9][0-9])(?<Month>([0][1-9])|([1][0-2]))(?<Day>([0-2][0-9])|([3][0-1]))(?<Gender>[0-9])(?<Series>[0-9]{3})(?<Citizenship>[0-9])(?<Uniform>[0-9])(?<Control>[0-9])"; #endregion #region Constuctors /// <summary> /// Sets up the shared objects for ID validation. /// </summary> static IdentityNumber() { _expression = new Regex(_IDExpression, RegexOptions.Compiled | RegexOptions.Singleline); } /// <summary> /// Creates the ID number from a string. /// </summary> /// <param name="IDNumber">The string ID number.</param> public IdentityNumber(string IDNumber) { _match = _expression.Match(IDNumber.Trim()); } #endregion #region Properties /// <summary> /// Indicates the date of birth encoded in the ID Number. /// </summary> /// <exception cref="System.ArgumentException">Thrown if the ID Number is not usable.</exception> public DateTime DateOfBirth { get { if(IsUsable == false) { throw new ArgumentException("ID Number is unusable!", "IDNumber"); } int year = int.Parse(_match.Groups["Year"].Value); // NOTE: Do not optimize by moving these to static, otherwise the calculation may be incorrect // over year changes, especially century changes. int currentCentury = int.Parse(DateTime.Now.Year.ToString().Substring(0, 2) + "00"); int lastCentury = currentCentury - 100; int currentYear = int.Parse(DateTime.Now.Year.ToString().Substring(2, 2)); // If the year is after or at the current YY, then add last century to it, otherwise add // this century. // TODO: YY -> YYYY logic needs thinking about if(year > currentYear) { year += lastCentury; } else { year += currentCentury; } return new DateTime(year, int.Parse(_match.Groups["Month"].Value), int.Parse(_match.Groups["Day"].Value)); } } /// <summary> /// Indicates the gender for the ID number. /// </summary> /// <exception cref="System.ArgumentException">Thrown if the ID Number is not usable.</exception> public PersonGender Gender { get { if(IsUsable == false) { throw new ArgumentException("ID Number is unusable!", "IDNumber"); } int gender = int.Parse(_match.Groups["Gender"].Value); if(gender < (int) PersonGender.Male) { return PersonGender.Female; } else { return PersonGender.Male; } } } /// <summary> /// Indicates the citizenship for the ID number. /// </summary> /// <exception cref="System.ArgumentException">Thrown if the ID Number is not usable.</exception> public PersonCitizenship Citizenship { get { if(IsUsable == false) { throw new ArgumentException("ID Number is unusable!", "IDNumber"); } return (PersonCitizenship) Enum.Parse(typeof(PersonCitizenship), _match.Groups["Citizenship"].Value); } } /// <summary> /// Indicates if the IDNumber is usable or not. /// </summary> public bool IsUsable { get { return _match.Success; } } /// <summary> /// Indicates if the IDNumber is valid or not. /// </summary> public bool IsValid { get { if(IsUsable == true) { // Calculate total A by adding the figures in the odd positions i.e. the first, third, fifth, // seventh, ninth and eleventh digits. int a = int.Parse(_match.Value.Substring(0, 1)) + int.Parse(_match.Value.Substring(2, 1)) + int.Parse(_match.Value.Substring(4, 1)) + int.Parse(_match.Value.Substring(6, 1)) + int.Parse(_match.Value.Substring(8, 1)) + int.Parse(_match.Value.Substring(10, 1)); // Calculate total B by taking the even figures of the number as a whole number, and then // multiplying that number by 2, and then add the individual figures together. int b = int.Parse(_match.Value.Substring(1, 1) + _match.Value.Substring(3, 1) + _match.Value.Substring(5, 1) + _match.Value.Substring(7, 1) + _match.Value.Substring(9, 1) + _match.Value.Substring(11, 1)); b *= 2; string bString = b.ToString(); b = 0; for(int index = 0; index < bString.Length; index++) { b += int.Parse(bString.Substring(index, 1)); } // Calculate total C by adding total A to total B. int c = a + b; // The control-figure can now be determined by subtracting the ones in figure C from 10. string cString = c.ToString() ; cString = cString.Substring(cString.Length - 1, 1) ; int control = 0; // Where the total C is a multiple of 10, the control figure will be 0. if(cString != "0") { control = 10 - int.Parse(cString.Substring(cString.Length - 1, 1)); } if(_match.Groups["Control"].Value == control.ToString()) { return true; } } return false; } } #endregion } } Here is the code from my default.aspx.cs page: using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.UI; using System.Web.UI.WebControls; using Utilities.Southafrica; <- this is the one i added to public partial class _Default : System.Web.UI.Page { protected void Page_Load(object sender, EventArgs e) { var someNumber = new IdentityNumber("123456"); <- gives error } } Can someone please tell the syntax for how I pass an id number to the class? Thanks

  Read the article

• Custom language - FOR loop in a clojure interpeter?

  - by Mark

  I have a basic interpreter in clojure. Now i need to implement for (initialisation; finish-test; loop-update) { statements } Implement a similar for-loop for the interpreted language. The pattern will be: (for variable-declarations end-test loop-update do statement) The variable-declarations will set up initial values for variables.The end-test returns a boolean, and the loop will end if end-test returns false. The statement is interpreted followed by the loop-update for each pass of the loop. Examples of use are: (run ’(for ((i 0)) (< i 10) (set i (+ 1 i)) do (println i))) (run ’(for ((i 0) (j 0)) (< i 10) (seq (set i (+ 1 i)) (set j (+ j (* 2 i)))) do (println j))) inside my interpreter. I will attach my interpreter code I got so far. Any help is appreciated. Interpreter (declare interpret make-env) ;; needed as language terms call out to 'interpret' (def do-trace false) ;; change to 'true' to show calls to 'interpret' ;; simple utilities (def third ; return third item in a list (fn [a-list] (second (rest a-list)))) (def fourth ; return fourth item in a list (fn [a-list] (third (rest a-list)))) (def run ; make it easy to test the interpreter (fn [e] (println "Processing: " e) (println "=> " (interpret e (make-env))))) ;; for the environment (def make-env (fn [] '())) (def add-var (fn [env var val] (cons (list var val) env))) (def lookup-var (fn [env var] (cond (empty? env) 'error (= (first (first env)) var) (second (first env)) :else (lookup-var (rest env) var)))) ;; for terms in language ;; -- define numbers (def is-number? (fn [expn] (number? expn))) (def interpret-number (fn [expn env] expn)) ;; -- define symbols (def is-symbol? (fn [expn] (symbol? expn))) (def interpret-symbol (fn [expn env] (lookup-var env expn))) ;; -- define boolean (def is-boolean? (fn [expn] (or (= expn 'true) (= expn 'false)))) (def interpret-boolean (fn [expn env] expn)) ;; -- define functions (def is-function? (fn [expn] (and (list? expn) (= 3 (count expn)) (= 'lambda (first expn))))) (def interpret-function ; keep function definitions as they are written (fn [expn env] expn)) ;; -- define addition (def is-plus? (fn [expn] (and (list? expn) (= 3 (count expn)) (= '+ (first expn))))) (def interpret-plus (fn [expn env] (+ (interpret (second expn) env) (interpret (third expn) env)))) ;; -- define subtraction (def is-minus? (fn [expn] (and (list? expn) (= 3 (count expn)) (= '- (first expn))))) (def interpret-minus (fn [expn env] (- (interpret (second expn) env) (interpret (third expn) env)))) ;; -- define multiplication (def is-times? (fn [expn] (and (list? expn) (= 3 (count expn)) (= '* (first expn))))) (def interpret-times (fn [expn env] (* (interpret (second expn) env) (interpret (third expn) env)))) ;; -- define division (def is-divides? (fn [expn] (and (list? expn) (= 3 (count expn)) (= '/ (first expn))))) (def interpret-divides (fn [expn env] (/ (interpret (second expn) env) (interpret (third expn) env)))) ;; -- define equals test (def is-equals? (fn [expn] (and (list? expn) (= 3 (count expn)) (= '= (first expn))))) (def interpret-equals (fn [expn env] (= (interpret (second expn) env) (interpret (third expn) env)))) ;; -- define greater-than test (def is-greater-than? (fn [expn] (and (list? expn) (= 3 (count expn)) (= '> (first expn))))) (def interpret-greater-than (fn [expn env] (> (interpret (second expn) env) (interpret (third expn) env)))) ;; -- define not (def is-not? (fn [expn] (and (list? expn) (= 2 (count expn)) (= 'not (first expn))))) (def interpret-not (fn [expn env] (not (interpret (second expn) env)))) ;; -- define or (def is-or? (fn [expn] (and (list? expn) (= 3 (count expn)) (= 'or (first expn))))) (def interpret-or (fn [expn env] (or (interpret (second expn) env) (interpret (third expn) env)))) ;; -- define and (def is-and? (fn [expn] (and (list? expn) (= 3 (count expn)) (= 'and (first expn))))) (def interpret-and (fn [expn env] (and (interpret (second expn) env) (interpret (third expn) env)))) ;; -- define print (def is-print? (fn [expn] (and (list? expn) (= 2 (count expn)) (= 'println (first expn))))) (def interpret-print (fn [expn env] (println (interpret (second expn) env)))) ;; -- define with (def is-with? (fn [expn] (and (list? expn) (= 3 (count expn)) (= 'with (first expn))))) (def interpret-with (fn [expn env] (interpret (third expn) (add-var env (first (second expn)) (interpret (second (second expn)) env))))) ;; -- define if (def is-if? (fn [expn] (and (list? expn) (= 4 (count expn)) (= 'if (first expn))))) (def interpret-if (fn [expn env] (cond (interpret (second expn) env) (interpret (third expn) env) :else (interpret (fourth expn) env)))) ;; -- define function-application (def is-function-application? (fn [expn env] (and (list? expn) (= 2 (count expn)) (is-function? (interpret (first expn) env))))) (def interpret-function-application (fn [expn env] (let [function (interpret (first expn) env)] (interpret (third function) (add-var env (first (second function)) (interpret (second expn) env)))))) ;; the interpreter itself (def interpret (fn [expn env] (cond do-trace (println "Interpret is processing: " expn)) (cond ; basic values (is-number? expn) (interpret-number expn env) (is-symbol? expn) (interpret-symbol expn env) (is-boolean? expn) (interpret-boolean expn env) (is-function? expn) (interpret-function expn env) ; built-in functions (is-plus? expn) (interpret-plus expn env) (is-minus? expn) (interpret-minus expn env) (is-times? expn) (interpret-times expn env) (is-divides? expn) (interpret-divides expn env) (is-equals? expn) (interpret-equals expn env) (is-greater-than? expn) (interpret-greater-than expn env) (is-not? expn) (interpret-not expn env) (is-or? expn) (interpret-or expn env) (is-and? expn) (interpret-and expn env) (is-print? expn) (interpret-print expn env) ; special syntax (is-with? expn) (interpret-with expn env) (is-if? expn) (interpret-if expn env) ; functions (is-function-application? expn env) (interpret-function-application expn env) :else 'error))) ;; tests of using environment (println "Environment tests:") (println (add-var (make-env) 'x 1)) (println (add-var (add-var (add-var (make-env) 'x 1) 'y 2) 'x 3)) (println (lookup-var '() 'x)) (println (lookup-var '((x 1)) 'x)) (println (lookup-var '((x 1) (y 2)) 'x)) (println (lookup-var '((x 1) (y 2)) 'y)) (println (lookup-var '((x 3) (y 2) (x 1)) 'x)) ;; examples of using interpreter (println "Interpreter examples:") (run '1) (run '2) (run '(+ 1 2)) (run '(/ (* (+ 4 5) (- 2 4)) 2)) (run '(with (x 1) x)) (run '(with (x 1) (with (y 2) (+ x y)))) (run '(with (x (+ 2 4)) x)) (run 'false) (run '(not false)) (run '(with (x true) (with (y false) (or x y)))) (run '(or (= 3 4) (> 4 3))) (run '(with (x 1) (if (= x 1) 2 3))) (run '(with (x 2) (if (= x 1) 2 3))) (run '((lambda (n) (* 2 n)) 4)) (run '(with (double (lambda (n) (* 2 n))) (double 4))) (run '(with (sum-to (lambda (n) (if (= n 0) 0 (+ n (sum-to (- n 1)))))) (sum-to 100))) (run '(with (x 1) (with (f (lambda (n) (+ n x))) (with (x 2) (println (f 3))))))

  Read the article

• how to pass an id number string to this class (asp.net, c#)

  - by Phil

  I'm very much a vb person, but have had to use this id number class in c#. I got it from http://www.codingsanity.com/idnumber.htm : using System; using System.Text.RegularExpressions; namespace Utilities.SouthAfrica { /// <summary> /// Represents a South African Identity Number. /// valid number = 7707215230080 /// invalid test number = 1234567891234 /// /// </summary> [Serializable()] public class IdentityNumber { #region Enumerations /// <summary> /// Indicates a gender. /// </summary> public enum PersonGender { Female = 0, Male = 5 } public enum PersonCitizenship { SouthAfrican = 0, Foreign = 1 } #endregion #region Declarations static Regex _expression; Match _match; const string _IDExpression = @"(?<Year>[0-9][0-9])(?<Month>([0][1-9])|([1][0-2]))(?<Day>([0-2][0-9])|([3][0-1]))(?<Gender>[0-9])(?<Series>[0-9]{3})(?<Citizenship>[0-9])(?<Uniform>[0-9])(?<Control>[0-9])"; #endregion #region Constuctors /// <summary> /// Sets up the shared objects for ID validation. /// </summary> static IdentityNumber() { _expression = new Regex(_IDExpression, RegexOptions.Compiled | RegexOptions.Singleline); } /// <summary> /// Creates the ID number from a string. /// </summary> /// <param name="IDNumber">The string ID number.</param> public IdentityNumber(string IDNumber) { _match = _expression.Match(IDNumber.Trim()); } #endregion #region Properties /// <summary> /// Indicates the date of birth encoded in the ID Number. /// </summary> /// <exception cref="System.ArgumentException">Thrown if the ID Number is not usable.</exception> public DateTime DateOfBirth { get { if(IsUsable == false) { throw new ArgumentException("ID Number is unusable!", "IDNumber"); } int year = int.Parse(_match.Groups["Year"].Value); // NOTE: Do not optimize by moving these to static, otherwise the calculation may be incorrect // over year changes, especially century changes. int currentCentury = int.Parse(DateTime.Now.Year.ToString().Substring(0, 2) + "00"); int lastCentury = currentCentury - 100; int currentYear = int.Parse(DateTime.Now.Year.ToString().Substring(2, 2)); // If the year is after or at the current YY, then add last century to it, otherwise add // this century. // TODO: YY -> YYYY logic needs thinking about if(year > currentYear) { year += lastCentury; } else { year += currentCentury; } return new DateTime(year, int.Parse(_match.Groups["Month"].Value), int.Parse(_match.Groups["Day"].Value)); } } /// <summary> /// Indicates the gender for the ID number. /// </summary> /// <exception cref="System.ArgumentException">Thrown if the ID Number is not usable.</exception> public PersonGender Gender { get { if(IsUsable == false) { throw new ArgumentException("ID Number is unusable!", "IDNumber"); } int gender = int.Parse(_match.Groups["Gender"].Value); if(gender < (int) PersonGender.Male) { return PersonGender.Female; } else { return PersonGender.Male; } } } /// <summary> /// Indicates the citizenship for the ID number. /// </summary> /// <exception cref="System.ArgumentException">Thrown if the ID Number is not usable.</exception> public PersonCitizenship Citizenship { get { if(IsUsable == false) { throw new ArgumentException("ID Number is unusable!", "IDNumber"); } return (PersonCitizenship) Enum.Parse(typeof(PersonCitizenship), _match.Groups["Citizenship"].Value); } } /// <summary> /// Indicates if the IDNumber is usable or not. /// </summary> public bool IsUsable { get { return _match.Success; } } /// <summary> /// Indicates if the IDNumber is valid or not. /// </summary> public bool IsValid { get { if(IsUsable == true) { // Calculate total A by adding the figures in the odd positions i.e. the first, third, fifth, // seventh, ninth and eleventh digits. int a = int.Parse(_match.Value.Substring(0, 1)) + int.Parse(_match.Value.Substring(2, 1)) + int.Parse(_match.Value.Substring(4, 1)) + int.Parse(_match.Value.Substring(6, 1)) + int.Parse(_match.Value.Substring(8, 1)) + int.Parse(_match.Value.Substring(10, 1)); // Calculate total B by taking the even figures of the number as a whole number, and then // multiplying that number by 2, and then add the individual figures together. int b = int.Parse(_match.Value.Substring(1, 1) + _match.Value.Substring(3, 1) + _match.Value.Substring(5, 1) + _match.Value.Substring(7, 1) + _match.Value.Substring(9, 1) + _match.Value.Substring(11, 1)); b *= 2; string bString = b.ToString(); b = 0; for(int index = 0; index < bString.Length; index++) { b += int.Parse(bString.Substring(index, 1)); } // Calculate total C by adding total A to total B. int c = a + b; // The control-figure can now be determined by subtracting the ones in figure C from 10. string cString = c.ToString() ; cString = cString.Substring(cString.Length - 1, 1) ; int control = 0; // Where the total C is a multiple of 10, the control figure will be 0. if(cString != "0") { control = 10 - int.Parse(cString.Substring(cString.Length - 1, 1)); } if(_match.Groups["Control"].Value == control.ToString()) { return true; } } return false; } } #endregion } } Can someone please tell the syntax for how I pass an id number to the class? Thanks

  Read the article

• Am I just not understanding TDD unit testing (Asp.Net MVC project)?

  - by KallDrexx

  I am trying to figure out how to correctly and efficiently unit test my Asp.net MVC project. When I started on this project I bought the Pro ASP.Net MVC, and with that book I learned about TDD and unit testing. After seeing the examples, and the fact that I work as a software engineer in QA in my current company, I was amazed at how awesome TDD seemed to be. So I started working on my project and went gun-ho writing unit tests for my database layer, business layer, and controllers. Everything got a unit test prior to implementation. At first I thought it was awesome, but then things started to go downhill. Here are the issues I started encountering: I ended up writing application code in order to make it possible for unit tests to be performed. I don't mean this in a good way as in my code was broken and I had to fix it so the unit test pass. I mean that abstracting out the database to a mock database is impossible due to the use of linq for data retrieval (using the generic repository pattern). The reason is that with linq-sql or linq-entities you can do joins just by doing: var objs = select p from _container.Projects select p.Objects; However, if you mock the database layer out, in order to have that linq pass the unit test you must change the linq to be var objs = select p from _container.Projects join o in _container.Objects on o.ProjectId equals p.Id select o; Not only does this mean you are changing your application logic just so you can unit test it, but you are making your code less efficient for the sole purpose of testability, and getting rid of a lot of advantages using an ORM has in the first place. Furthermore, since a lot of the IDs for my models are database generated, I proved to have to write additional code to handle the non-database tests since IDs were never generated and I had to still handle those cases for the unit tests to pass, yet they would never occur in real scenarios. Thus I ended up throwing out my database unit testing. Writing unit tests for controllers was easy as long as I was returning views. However, the major part of my application (and the one that would benefit most from unit testing) is a complicated ajax web application. For various reasons I decided to change the app from returning views to returning JSON with the data I needed. After this occurred my unit tests became extremely painful to write, as I have not found any good way to write unit tests for non-trivial json. After pounding my head and wasting a ton of time trying to find a good way to unit test the JSON, I gave up and deleted all of my controller unit tests (all controller actions are focused on this part of the app so far). So finally I was left with testing the Service layer (BLL). Right now I am using EF4, however I had this issue with linq-sql as well. I chose to do the EF4 model-first approach because to me, it makes sense to do it that way (define my business objects and let the framework figure out how to translate it into the sql backend). This was fine at the beginning but now it is becoming cumbersome due to relationships. For example say I have Project, User, and Object entities. One Object must be associated to a project, and a project must be associated to a user. This is not only a database specific rule, these are my business rules as well. However, say I want to do a unit test that I am able to save an object (for a simple example). I now have to do the following code just to make sure the save worked: User usr = new User { Name = "Me" }; _userService.SaveUser(usr); Project prj = new Project { Name = "Test Project", Owner = usr }; _projectService.SaveProject(prj); Object obj = new Object { Name = "Test Object" }; _objectService.SaveObject(obj); // Perform verifications There are many issues with having to do all this just to perform one unit test. There are several issues with this. For starters, if I add a new dependency, such as all projects must belong to a category, I must go into EVERY single unit test that references a project, add code to save the category then add code to add the category to the project. This can be a HUGE effort down the road for a very simple business logic change, and yet almost none of the unit tests I will be modifying for this requirement are actually meant to test that feature/requirement. If I then add verifications to my SaveProject method, so that projects cannot be saved unless they have a name with at least 5 characters, I then have to go through every Object and Project unit test to make sure that the new requirement doesn't make any unrelated unit tests fail. If there is an issue in the UserService.SaveUser() method it will cause all project, and object unit tests to fail and it the cause won't be immediately noticeable without having to dig through the exceptions. Thus I have removed all service layer unit tests from my project. I could go on and on, but so far I have not seen any way for unit testing to actually help me and not get in my way. I can see specific cases where I can, and probably will, implement unit tests, such as making sure my data verification methods work correctly, but those cases are few and far between. Some of my issues can probably be mitigated but not without adding extra layers to my application, and thus making more points of failure just so I can unit test. Thus I have no unit tests left in my code. Luckily I heavily use source control so I can get them back if I need but I just don't see the point. Everywhere on the internet I see people talking about how great TDD unit tests are, and I'm not just talking about the fanatical people. The few people who dismiss TDD/Unit tests give bad arguments claiming they are more efficient debugging by hand through the IDE, or that their coding skills are amazing that they don't need it. I recognize that both of those arguments are utter bullocks, especially for a project that needs to be maintainable by multiple developers, but any valid rebuttals to TDD seem to be few and far between. So the point of this post is to ask, am I just not understanding how to use TDD and automatic unit tests?

  Read the article

• C++/CLI HTTP Proxy problems...

  - by darkantimatter

  Hi, I'm trying(very hard) to make a small HTTP Proxy server which I can use to save all communications to a file. Seeing as I dont really have any experience in the area, I used a class from codeproject.com and some associated code to get started (It was made in the old CLI syntax, so I converted it). I couldn't get it working, so I added lots more code to make it work (threads etc), and now it sort of works. Basically, it recieves something from a client (I just configured Mozilla Firefox to route its connections through this proxy) and then routes it to google.com. After it sends Mozilla's data to google, recieves a responce, and sends that to Mozilla. This works fine, but then the proxy fails to recieve any data from Mozilla. It just loops in the Sleep(50) section. Anyway, heres the code: ProxyTest.cpp: #include "stdafx.h" #include "windows.h" #include "CHTTPProxy.h" public ref class ClientThread { public: System::Net::Sockets::TcpClient ^ pClient; CHttpProxy ^ pProxy; System::Int32 ^ pRecieveBufferSize; System::Threading::Thread ^ Thread; ClientThread(System::Net::Sockets::TcpClient ^ sClient, CHttpProxy ^ sProxy, System::Int32 ^ sRecieveBufferSize) { pClient = sClient; pProxy = sProxy; pRecieveBufferSize = sRecieveBufferSize; }; void StartReading() { Thread = gcnew System::Threading::Thread(gcnew System::Threading::ThreadStart(this,&ClientThread::ThreadEntryPoint)); Thread->Start(); }; void ThreadEntryPoint() { char * bytess; bytess = new char[(int)pRecieveBufferSize]; memset(bytess, 0, (int)pRecieveBufferSize); array<unsigned char> ^ bytes = gcnew array<unsigned char>((int)pRecieveBufferSize); array<unsigned char> ^ sendbytes; do { if (pClient->GetStream()->DataAvailable) { try { do { Sleep(100); //Lets wait for whole packet to get cached (If it even does...) unsigned int k = pClient->GetStream()->Read(bytes, 0, (int)pRecieveBufferSize); //Read it for(unsigned int i=0; i<(int)pRecieveBufferSize; i++) bytess[i] = bytes[i]; Console::WriteLine("Packet Received:\n"+gcnew System::String(bytess)); pProxy->SendToServer(bytes,pClient->GetStream()); //Now send it to google! pClient->GetStream()->Flush(); } while(pClient->GetStream()->DataAvailable); } catch (Exception ^ e) { break; } } else { Sleep(50); //It just loops here because it thinks mozilla isnt sending anything if (!(pClient->Connected)) break; }; } while (pClient->GetStream()->CanRead); delete [] bytess; pClient->Close(); }; }; int main(array<System::String ^> ^args) { System::Collections::Generic::Stack<ClientThread ^> ^ Clients = gcnew System::Collections::Generic::Stack<ClientThread ^>(); System::Net::Sockets::TcpListener ^ pTcpListener = gcnew System::Net::Sockets::TcpListener(8080); pTcpListener->Start(); System::Net::Sockets::TcpClient ^ pTcpClient; while (1) { pTcpClient = pTcpListener->AcceptTcpClient(); //Wait for client ClientThread ^ Client = gcnew ClientThread(pTcpClient, gcnew CHttpProxy("www.google.com.au", 80), pTcpClient->ReceiveBufferSize); //Make a new object for this client Client->StartReading(); //Start the thread Clients->Push(Client); //Add it to the list }; pTcpListener->Stop(); return 0; } CHTTPProxy.h, from http://www.codeproject.com/KB/IP/howtoproxy.aspx with a lot of modifications: //THIS FILE IS FROM http://www.codeproject.com/KB/IP/howtoproxy.aspx. I DID NOT MAKE THIS! BUT I HAVE MADE SEVERAL MODIFICATIONS! #using <mscorlib.dll> #using <SYSTEM.DLL> using namespace System; using System::Net::Sockets::TcpClient; using System::String; using System::Exception; using System::Net::Sockets::NetworkStream; #include <stdio.h> ref class CHttpProxy { public: CHttpProxy(System::String ^ szHost, int port); System::String ^ m_host; int m_port; void SendToServer(array<unsigned char> ^ Packet, System::Net::Sockets::NetworkStream ^ sendstr); }; CHttpProxy::CHttpProxy(System::String ^ szHost, int port) { m_host = gcnew System::String(szHost); m_port = port; } void CHttpProxy::SendToServer(array<unsigned char> ^ Packet, System::Net::Sockets::NetworkStream ^ sendstr) { TcpClient ^ tcpclnt = gcnew TcpClient(); try { tcpclnt->Connect(m_host,m_port); } catch (Exception ^ e ) { Console::WriteLine(e->ToString()); return; } // Send it if ( tcpclnt ) { NetworkStream ^ networkStream; networkStream = tcpclnt->GetStream(); int size = Packet->Length; networkStream->Write(Packet, 0, size); array<unsigned char> ^ bytes = gcnew array<unsigned char>(tcpclnt->ReceiveBufferSize); char * bytess = new char[tcpclnt->ReceiveBufferSize]; Sleep(500); //Wait for responce do { unsigned int k = networkStream->Read(bytes, 0, (int)tcpclnt->ReceiveBufferSize); //Read from google for(unsigned int i=0; i<k; i++) { bytess[i] = bytes[i]; if (bytess[i] == 0) bytess[i] = ' '; //Dont terminate the string if (bytess[i] < 8) bytess[i] = ' '; //Somethings making the computer beep, and its not 7?!?! }; Console::WriteLine("\n\nAbove packet sent to google. Google Packet Received:\n"+gcnew System::String(bytess)); sendstr->Write(bytes,0,k); //Send it to mozilla Console::WriteLine("\n\nAbove packet sent to client..."); //Sleep(1000); } while(networkStream->DataAvailable); delete [] bytess; } return; } Any help would be much appreciated, I've tried for hours.

  Read the article

• A minimalistic smart array (container) class template

  - by legends2k

  I've written a (array) container class template (lets call it smart array) for using it in the BREW platform (which doesn't allow many C++ constructs like STD library, exceptions, etc. It has a very minimal C++ runtime support); while writing this my friend said that something like this already exists in Boost called MultiArray, I tried it but the ARM compiler (RVCT) cries with 100s of errors. I've not seen Boost.MultiArray's source, I've started learning templates only lately; template meta programming interests me a lot, although am not sure if this is strictly one that can be categorized thus. So I want all my fellow C++ aficionados to review it ~ point out flaws, potential bugs, suggestions, optimizations, etc.; something like "you've not written your own Big Three which might lead to...". Possibly any criticism that will help me improve this class and thereby my C++ skills. Edit: I've used std::vector since it's easily understood, later it will be replaced by a custom written vector class template made to work in the BREW platform. Also C++0x related syntax like static_assert will also be removed in the final code. smart_array.h #include <vector> #include <cassert> #include <cstdarg> using std::vector; template <typename T, size_t N> class smart_array { vector < smart_array<T, N - 1> > vec; public: explicit smart_array(vector <size_t> &dimensions) { assert(N == dimensions.size()); vector <size_t>::iterator it = ++dimensions.begin(); vector <size_t> dimensions_remaining(it, dimensions.end()); smart_array <T, N - 1> temp_smart_array(dimensions_remaining); vec.assign(dimensions[0], temp_smart_array); } explicit smart_array(size_t dimension_1 = 1, ...) { static_assert(N > 0, "Error: smart_array expects 1 or more dimension(s)"); assert(dimension_1 > 1); va_list dim_list; vector <size_t> dimensions_remaining(N - 1); va_start(dim_list, dimension_1); for(size_t i = 0; i < N - 1; ++i) { size_t dimension_n = va_arg(dim_list, size_t); assert(dimension_n > 0); dimensions_remaining[i] = dimension_n; } va_end(dim_list); smart_array <T, N - 1> temp_smart_array(dimensions_remaining); vec.assign(dimension_1, temp_smart_array); } smart_array<T, N - 1>& operator[](size_t index) { assert(index < vec.size() && index >= 0); return vec[index]; } size_t length() const { return vec.size(); } }; template<typename T> class smart_array<T, 1> { vector <T> vec; public: explicit smart_array(vector <size_t> &dimension) : vec(dimension[0]) { assert(dimension[0] > 0); } explicit smart_array(size_t dimension_1 = 1) : vec(dimension_1) { assert(dimension_1 > 0); } T& operator[](size_t index) { assert(index < vec.size() && index >= 0); return vec[index]; } size_t length() { return vec.size(); } }; Sample Usage: #include "smart_array.h" #include <iostream> using std::cout; using std::endl; int main() { // testing 1 dimension smart_array <int, 1> x(3); x[0] = 0, x[1] = 1, x[2] = 2; cout << "x.length(): " << x.length() << endl; // testing 2 dimensions smart_array <float, 2> y(2, 3); y[0][0] = y[0][1] = y[0][2] = 0; y[1][0] = y[1][1] = y[1][2] = 1; cout << "y.length(): " << y.length() << endl; cout << "y[0].length(): " << y[0].length() << endl; // testing 3 dimensions smart_array <char, 3> z(2, 4, 5); cout << "z.length(): " << z.length() << endl; cout << "z[0].length(): " << z[0].length() << endl; cout << "z[0][0].length(): " << z[0][0].length() << endl; z[0][0][4] = 'c'; cout << z[0][0][4] << endl; // testing 4 dimensions smart_array <bool, 4> r(2, 3, 4, 5); cout << "z.length(): " << r.length() << endl; cout << "z[0].length(): " << r[0].length() << endl; cout << "z[0][0].length(): " << r[0][0].length() << endl; cout << "z[0][0][0].length(): " << r[0][0][0].length() << endl; // testing copy constructor smart_array <float, 2> copy_y(y); cout << "copy_y.length(): " << copy_y.length() << endl; cout << "copy_x[0].length(): " << copy_y[0].length() << endl; cout << copy_y[0][0] << "\t" << copy_y[1][0] << "\t" << copy_y[0][1] << "\t" << copy_y[1][1] << "\t" << copy_y[0][2] << "\t" << copy_y[1][2] << endl; return 0; }

  Read the article

• Erroneous/Incorrect C2248 error using Visual Studio 2010

  - by Dylan Bourque

  I'm seeing what I believe to be an erroneous/incorrect compiler error using the Visual Studio 2010 compiler. I'm in the process of up-porting our codebase from Visual Studio 2005 and I ran across a construct that was building correctly before but now generates a C2248 compiler error. Obviously, the code snippet below has been generic-ized, but it is a compilable example of the scenario. The ObjectPtr<T> C++ template comes from our codebase and is the source of the error in question. What appears to be happening is that the compiler is generating a call to the copy constructor for ObjectPtr<T> when it shouldn't (see my comment block in the SomeContainer::Foo() method below). For this code construct, there is a public cast operator for SomeUsefulData * on ObjectPtr<SomeUsefulData> but it is not being chosen inside the true expression if the ?: operator. Instead, I get the two errors in the block quote below. Based on my knowledge of C++, this code should compile. Has anyone else seen this behavior? If not, can someone point me to a clarification of the compiler resolution rules that would explain why it's attempting to generate a copy of the object in this case? Thanks in advance, Dylan Bourque Visual Studio build output: c:\projects\objectptrtest\objectptrtest.cpp(177): error C2248: 'ObjectPtr::ObjectPtr' : cannot access private member declared in class 'ObjectPtr' with [ T=SomeUsefulData ] c:\projects\objectptrtest\objectptrtest.cpp(25) : see declaration of 'ObjectPtr::ObjectPtr' with [ T=SomeUsefulData ] c:\projects\objectptrtest\objectptrtest.cpp(177): error C2248: 'ObjectPtr::ObjectPtr' : cannot access private member declared in class 'ObjectPtr' with [ T=SomeUsefulData ] c:\projects\objectptrtest\objectptrtest.cpp(25) : see declaration of 'ObjectPtr::ObjectPtr' with [ T=SomeUsefulData ] Below is a minimal, compilable example of the scenario: #include <stdio.h> #include <tchar.h> template<class T> class ObjectPtr { public: ObjectPtr<T> (T* pObj = NULL, bool bShared = false) : m_pObject(pObj), m_bObjectShared(bShared) {} ~ObjectPtr<T> () { Detach(); } private: // private, unimplemented copy constructor and assignment operator // to guarantee that ObjectPtr<T> objects are not copied ObjectPtr<T> (const ObjectPtr<T>&); ObjectPtr<T>& operator = (const ObjectPtr<T>&); public: T * GetObject () { return m_pObject; } const T * GetObject () const { return m_pObject; } bool HasObject () const { return (GetObject()!=NULL); } bool IsObjectShared () const { return m_bObjectShared; } void ObjectShared (bool bShared) { m_bObjectShared = bShared; } bool IsNull () const { return !HasObject(); } void Attach (T* pObj, bool bShared = false) { Detach(); if (pObj != NULL) { m_pObject = pObj; m_bObjectShared = bShared; } } void Detach (T** ppObject = NULL) { if (ppObject != NULL) { *ppObject = m_pObject; m_pObject = NULL; m_bObjectShared = false; } else { if (HasObject()) { if (!IsObjectShared()) delete m_pObject; m_pObject = NULL; m_bObjectShared = false; } } } void Detach (bool bDeleteIfNotShared) { if (HasObject()) { if (bDeleteIfNotShared && !IsObjectShared()) delete m_pObject; m_pObject = NULL; m_bObjectShared = false; } } bool IsEqualTo (const T * pOther) const { return (GetObject() == pOther); } public: T * operator -> () { ASSERT(HasObject()); return m_pObject; } const T * operator -> () const { ASSERT(HasObject()); return m_pObject; } T & operator * () { ASSERT(HasObject()); return *m_pObject; } const T & operator * () const { ASSERT(HasObject()); return (const C &)(*m_pObject); } operator T * () { return m_pObject; } operator const T * () const { return m_pObject; } operator bool() const { return (m_pObject!=NULL); } ObjectPtr<T>& operator = (T * pObj) { Attach(pObj, false); return *this; } bool operator == (const T * pOther) const { return IsEqualTo(pOther); } bool operator == (T * pOther) const { return IsEqualTo(pOther); } bool operator != (const T * pOther) const { return !IsEqualTo(pOther); } bool operator != (T * pOther) const { return !IsEqualTo(pOther); } bool operator == (const ObjectPtr<T>& other) const { return IsEqualTo(other.GetObject()); } bool operator != (const ObjectPtr<T>& other) const { return !IsEqualTo(other.GetObject()); } bool operator == (int pv) const { return (pv==NULL)? IsNull() : (LPVOID(m_pObject)==LPVOID(pv)); } bool operator != (int pv) const { return !(*this == pv); } private: T * m_pObject; bool m_bObjectShared; }; // Some concrete type that holds useful data class SomeUsefulData { public: SomeUsefulData () {} ~SomeUsefulData () {} }; // Some concrete type that holds a heap-allocated instance of // SomeUsefulData class SomeContainer { public: SomeContainer (SomeUsefulData* pUsefulData) { m_pData = pUsefulData; } ~SomeContainer () { // nothing to do here } public: bool EvaluateSomeCondition () { // fake condition check to give us an expression // to use in ?: operator below return true; } SomeUsefulData* Foo () { // this usage of the ?: operator generates a C2248 // error b/c it's attempting to call the copy // constructor on ObjectPtr<T> return EvaluateSomeCondition() ? m_pData : NULL; /**********[ DISCUSSION ]********** The following equivalent constructs compile w/out error and behave correctly: (1) explicit cast to SomeUsefulData* as a comiler hint return EvaluateSomeCondition() ? (SomeUsefulData *)m_pData : NULL; (2) if/else instead of ?: if (EvaluateSomeCondition()) return m_pData; else return NULL; (3) skip the condition check and return m_pData as a SomeUsefulData* directly return m_pData; **********[ END DISCUSSION ]**********/ } private: ObjectPtr<SomeUsefulData> m_pData; }; int _tmain(int argc, _TCHAR* argv[]) { return 0; }

  Read the article

< Previous Page | 416 417 418 419 420 421 422  | Next Page >