Search Results

Search found 22871 results on 915 pages for 'automated install'.

Page 421/915 | < Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• Weird problem with Visual C++ 2010 Express

  - by Robert Vella

  This has happened before on my Vista Premium installation, and now it's happening on my Windows 7 Home Premium installation. Basically everytime I install Visual Studio Express 2010, it works fine for a random amount of time but then suddenly starts to hide from my sight -- that's the best way I can explain it. VS does not crash, and from what I can tell it does not freeze either; It continues to work, I can even "minimize" and "maximize" it; I simply cannot see it nor can I interact with it any meaningful way. Also: After the "crash" there are no logs in: Root\Program Files (x86)\Microsoft Visual Studio 10.0\Microsoft Visual C++ 2010 Express - ENU. Nor any other files created at the time of the crash. There are no traces in the event viewer. The program seems to be functioning perfectly in the process manager. If I reinstall Visual C++, it works normally for a seemingly random period of time before going cookoo again. I am stumped. This has never happened to me before, with any other program. And yet I doubt it really is a problem with Visual C++; More like something general that seems to have picked on it for some reason. Still, after a clean install with a new OS, I'm kinda thinking there's something wrong here. Any help would be appreciated, altough I suspect that the answer to this question will make me feel embarassed. P.S. Not sure if it helps, but I think around the same time I started having problems (On both installations) with windows turning off the display when I leave the computer, and then seemingly crashing when it turns it on again -- in fact when I interact with it it seems to be responding to my commands without actually display anything.

  Read the article

• Dialog box tells me there's a missing driver when installing 64-bit version of Windows 7

  - by Eikern

  I'm trying to install Windows 7 64-bit on my computer (ASUS P6T Deluxe V2, one 80GB HDD and two 1 TB HDDs). When I'm supposed to select whether I want to Upgrade or do a Custom install, I get a dialog box telling me: Load Driver A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the Windows installation media is in the CD/DVD drive, you can safely remove it for this step. I've tried to reach this step using a 32-bit installation disc, but that doesn't generate this message at all. Through the command windows (shift-F10) I can reach all of my drives, including my optical drive, without any problems--so what kind of device driver is it the installation wants? I've tried all the obvious drivers on the CD that followed my motherboard, but I can't seem to find the right one. The problem is that I don't know what device I'm supposed to load the drivers for in the first place. Can anyone help me? Edit: It turned out that my downloaded image was corrupted. I borrowed a DVD from a friend of mine, which worked!

  Read the article

• Automatic driver search & update on Windows?

  - by Ben

  I have a Dell laptop issued by my employer, and I always find it a real pain to search for, download and maintain their drivers. It baffles me that there does not seem to be a nice way (product, website, ...) to just download the stuff you need, without hassle. The same goes for the other Windows based laptops in my direct environment. Are there any (preferably free) automated solutions available? Or do you have a nice workflow - other than searching the manufacturers website - to help smoothing this process?

  Read the article

• Serve my website from different server during downtime

  - by nfedyashev.mp

  I have a VPS server running in the cloud. Fully automated server image upgrade/downgrade(by RAM/HDD plans). The problem is that server upgrade/downgrade takes time and involves total unavailability during this period(up to 30 minutes). Goal: during this downtime server my website(http://mydomain.here) from different server with some message like "Under construction". How can I do this? -- mydomain.here is hosted on godaddy and uses its DNS(If I call it right). It's pointing with A-record to my VPS's IP address now. Change in these DNS settings will take more than 30minutes, so it's not an option. How can I find mode "dynamic" DNS? What should I learn?

  Read the article

• grub2 error : out of disk

  - by Nostradamnit

  Hi everyone, I recently install ArchBang on a machine with Ubuntu and XP. I ran update-grub from Ubuntu and it found the new install and created an entry. However, when I try to boot it, I get: error: out of disk error: you need to load kernel first I've tried several things, including adding a new entry in 40_custom, but nothing changes. Here are the entries I have: default found by update-grub ### BEGIN /etc/grub.d/30_os-prober ### menuentry "ArchBang Linux (on /dev/sda4)" { insmod part_msdos insmod ext2 set root='(hd0,msdos4)' search --no-floppy --fs-uuid --set 75f96b44-3a8f-4727-9959-d669b9244f2a linux /boot/vmlinuz26 root=/dev/sda4 rootfstype=ext4 ro xorg=vesa quiet nomodeset swapon initrd /boot/kernel26.img } menuentry "ArchBang Linux Fallback (on /dev/sda4)" { insmod part_msdos insmod ext2 set root='(hd0,msdos4)' search --no-floppy --fs-uuid --set 75f96b44-3a8f-4727-9959-d669b9244f2a linux /boot/vmlinuz26 root=/dev/sda4 rootfstype=ext4 ro xorg=vesa quiet nomodeset swapon initrd /boot/kernel26-fallback.img } ### END /etc/grub.d/30_os-prober ### custom entry in 40_custom based on various ideas found on the internets menuentry "ArchBang Linux (on /dev/sda4)" { insmod part_msdos insmod ext2 set root='(hd0,msdos4)' search --no-floppy --fs-uuid --set 75f96b44-3a8f-4727-9959-d669b9244f2a linux /boot/vmlinuz26 root=/dev/disk/by-uuid/75f96b44-3a8f-4727-9959-d669b9244f2a rootfstype=ext4 ro xorg=vesa quiet nomodeset swapon initrd /boot/kernel26.img } I think the problem has something to do with the sda4 not being mounted at boot-time... Thanks in advance for you help, Sam

  Read the article

• Can I boot up a virtual machine natively?

  - by Anshul

  My question is: Is is possible to run a virtual machine natively on your hardware if you have installed the proper drivers etc? In other words, can I use a VHD as a regular hard drive to boot from? The reason I want to do this is that I do both graphics-intensive and audio-intensive work, but my computer is not powerful enough to handle both at the same time and many times I install a bunch of audio programs that I don't want affecting the stability of my graphics programs. Basically I wanted to have sandboxing between the two sets of applications. So I tried running the graphics-intensive programs in a VirtualBox VM and the audio-intensive work natively (simply because it's a pain to route ASIO audio devices in/out of VirtualBox). This kind-of works - the graphics-intensive stuff is tolerable, but still relatively slow, because it's running inside a VM. So my next idea was to just dual-boot and install the graphics and audio programs in separate partitions but I frequently use them in tandem, so it wouldn't be practical to reboot my machine every time I need to use the other set of programs. But I could live with this scenario: If I need to do more audio-intensive stuff, I'll just boot up to the audio partition and run the graphics programs in a VM, and then when I'm working heavily on the graphics part, I'll just boot the graphics partition as a regular OS directly on the hardware. Is this possible? For example by booting up a VHD as a regular hard drive? Or by setting up dual-boot, and every time the audio partition is shut down, synchronize the graphics VM VHD with the native graphics partition? Is it practical, given the above scenario? And if it's not possible, barring buying another computer, can anyone suggest a best-of-all-worlds setup (the two worlds being performance, sandboxing, and running in parallel) for the above scenario? Thanks in advance.

  Read the article

• Setting up scripts in Amazon EC2 Cloud

  - by racket99

  Hello, I am currently running a few perl and python scripts on a windows pc and would like to port over to the Amazon EC2 servers running 64-bit LINUX. The scripts are basic web scrapers that go to a variety of websites, get data and then save daily as csv files. I would like to install these in the cloud and get them running in an automated way so that they will run without my intervention. Also given that I don't want to lose all the data if the instance crashes, I should also upload the csv files to Amazon S3. Any idea how I can do this? I am not terribly versed in LINUX nor do I know Perl/Python well. What is the best way for me to tackle thi

  Read the article

• Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

  - by Shasteriskt

  I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

  Read the article

• fglrx-legacy-driver not seeing Radeon HD 4650 AGP

  - by Rocket Hazmat

  I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got fglrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci EDIT: fglrx 12.4 seems to work. Thing is, since I am on kernel 3.2, I need to apply this patch to common/lib/modules/fglrx/build_mod/firegl_public.c. I thought ATI dropped support for the 4xxx series after 12.4. Why doesn't 12.6 legacy work?

  Read the article

• Linux Software RAID1: How to boot after (physically) removing /dev/sda? (LVM, mdadm, Grub2)

  - by flight

  A server set up with Debian 6.0/squeeze. During the squeeze installation, I configured the two 500GB SATA disks (/dev/sda and /dev/sdb) as a RAID1 (managed with mdadm). The RAID keeps a 500 GB LVM volume group (vg0). In the volume group, there's a single logical volume (lv0). vg0-lv0 is formatted with extfs3 and mounted as root partition (no dedicated /boot partition). The system boots using GRUB2. In normal use, the systems boots fine. Also, when I tried and removed the second SATA drive (/dev/sdb) after a shutdown, the system came up without problem, and after reconnecting the drive, I was able to --re-add /dev/sdb1 to the RAID array. But: After removing the first SATA drive (/dev/sda), the system won't boot any more! A GRUB welcome message shows up for a second, then the system reboots. I tried to install GRUB2 manually on /dev/sdb ("grub-install /dev/sdb"), but that doesn't help. Appearently squeeze fails to set up GRUB2 to launch from the second disk when the first disk is removed, which seems to be quite an essential feature when running this kind of Software RAID1, isn't it? At the moment, I'm lost whether this is a problem with GRUB2, with LVM or with the RAID setup. Any hints?

  Read the article

• Building PHP For MacOS

  - by Eray

  I was using XAMPP and decided to uninstall it and use MacOS' in-built apache and php modules. But while uninstalling XAMPP I deleted /usr/bin/php files and other PHP-CLI files accidentally. And I decided to install newest version of PHP (5.5.12) instead of rebuilding current version (5.4.24). Downloaded it and unzip. After this executed this command as mentioned at this guide. ./configure '--with-apxs2=/usr/sbin/apxs' '--enable-cli' '--with-config-file-path=/etc' '--with-zlib=/usr' '--enable-bcmath' '--with-bz2=/usr' '--enable-calendar' '--disable-cgi' '--with-curl=/usr' '--enable-dba' '--enable-ndbm=/usr' '--enable-exif' '--enable-fpm' '--enable-ftp' '--with-gd' '--enable-gd-native-ttf' '--enable-mbregex' '--with-mysql=mysqlnd' '--with-mysqli=mysqlnd' '--with-pear' '--with-pdo-mysql=mysqlnd' '--with-mysql-sock=/var/mysql/mysql.sock' '--with-tidy' '--enable-wddx' '--with-xmlrpc' '--enable-zip' make make install When i check phpinfo() , it's still version 5.4.24 . This line from my httpd.conf LoadModule php5_module libexec/apache2/libphp5.so /usr/libexec/apache2/libphp5.so coming from old version and i couldn't ind libphp5.so for new version. There is no libphp5.so file inside modules dir. How can i use new PHP build with Apache ? UPDATE Results of php -v command . PHP 5.5.12 (cli) (built: May 27 2014 05:17:21) Copyright (c) 1997-2014 The PHP GroupZend Engine v2.5.0, Copyright (c) 1998-2014 Zend Technologies

  Read the article

• Ignore non-unicode programs language when installing software

  - by mitya

  This is something that is driving me nuts for a while and I haven't been able to find a solution for this problem anywhere. I am running Windows 7 and my "Language for non-Unicode programs" setting is set to Russian. I need for some non-unicode software that has a Russian UI. However, for most of my software I prefer to use the English UI. A lot of software out there is multilingual and is too smart for my liking. When installing, it switches the UI to Russian and the software UI stays in Russian after the installation without an option to change that, besides setting the "non-unicode language" to English. It switches back to Russian once I revert the setting and reboot. Most of the time it is driver software, i.e: Intel, HP, etc. How can force the installation to run English and stay that way after install, ignoring the "Language for non-Unicode programs" setting? Now, I understand this might be specific to the installer: MSI, Install Shield, etc. But any solution will be good, even if I have to apply it for every software installation. Thanks in advance for any helpful information!

  Read the article

• Have OS X send wake on lan before printing to shared printer

  - by Dean Hill

  I have a MacBook that prints to a shared Windows 7 printer. Sometimes the Windows machine is asleep, and the Mac will just queue up its print requests. I recently created a script to send a wake-on-lan packet to a Windows 7 machine. This wakes up the Windows machine and printing starts. Great, but I think the system can be automated en Is it possible to have the MacBook run the wake-on-lan script everytime something is printed? Stated more generally, can I have the OS X print subsystem execute a script everytime something is printed?

  Read the article

• Transferring filesystem-structured music collection to ipod

  - by ansgri

  I have a rather large music collection organized like music/<artist>/<album>/<track>-<title>.<fmt>, mostly mp3. However, the tagging is rather inconsistent, as on the PC or with better old players (Cowon D2+) I don't care and use the filesystem view. However, in the iTunes this all gets messed up because it doesn't care about file locations and looks at tags. What's worse though, it consistently splits compilations into single-track artist-albums. So, is there a way to take the existing filesystem artist-album structure and bring it to the form compatible with iTunes/iPod? Again, I don't care about tags. Automated approach is most welcome, but at least please direct me to some document specifying all the little details about iTunes' metadata requirement for compilations.

  Read the article

• Licensing SQL Server 2012 Reporting Services w/ SharePoint 2010

  - by Evan M.

  Here's my situation: I have 1 VM that is running SharePoint 2010 SP1. I have a different physical server that is running SQL Server 2008 R2 that hosts all the configuration and content database for SharePoint. Now, we want to start providing BI capabilities to our users with SharePoint and SQL Server. With it's new features, 2012 is the obvious way to go. To support this, I'm looking to build a new VM that will have SQL Server 2012 installed w/ Analysis services and SSIS, which will be the platform that gets our data from our Oracle databases, puts it in a warehouse hosted by the SQL 2012 instance, and is put into cubes. What's getting me about the platform is licensing for Reporting Services and PowerPivot. My plan was to install SSRS and PowerPivot on the current SharePoint server. But my understanding of the licensing means that instead of the new SQL server being licensed, I'd have to license both new server, and the SharePoint server. Conversely, I could install SharePoint onto the SQL server, and only have to get a second SP license, but then I'd have the added complexity of deploying a separated application server, and combines my data and application servers. Is my licensing understanding correct, or can I have SSRS and PowerPivot installed separately without incurring additional licensing costs?

  Read the article

• Update in grub.cfg file for loading new kernel image in Ubuntu 11.04

  - by user1627657

  I am new to Linux. I am compiling Linux kernel (ver: 2.6.34.12) in gcc in traditional manner in VMware machine in Ubuntu (kernel version - 2.6.38-8-generic) 11.04 version. I am unable to find, where to update about newly compiled kernel in the grub.cfg file. I updated the newly created image version name in the existing image. Then VMware didn't able to load new kernel. I have searched in internet but I didn't find. So anyone can help me, to update in the grub.cfg and to successfully load new kernel. Few things about what I have done: Make bzImage to create image file. Make modules_install && make install to install modules and then sudo mkinitramfs -o initramfs.img-2.6.34 2.6.34. Then sudo gedit grub.cfg. In that at the mementry I updated the version of vmlinuz and initrd from 2.6.38-8 to 2.6.34.12. This is I have done.

  Read the article

• Read ahead buffering while playing video file from optical disc

  - by Saxtus

  I was wondering if there is a program for Windows 7 (64-bit), that reads ahead the file to be played back (usually MKV files in my case) to the RAM, so the disc that the video file resides in, won't spin for the entire duration of the playback, but only every time the cache is almost empty (with big enough cache so it won't need the drive for long periods). A program that I've used in the past (called DVDIdle), was doing that universally for every video player I wanted, but they've stopped updating it 6 years ago and now it doesn't seem to work with Windows 7 (tried using compatibility mode too). The method I am using now, is to either have the drive wearing down and buzzing all the time or manually copy the entire file to HDD, SSD or RamDisk and play it from there. The closest thing I've found, is a software that slows down the drive's spin speed, but I was looking for something more convenient, automated, without waiting for an entire file to be copied before starting playback or needing any HDD space, like I've used to in the past. Thanks in advance.

  Read the article

• How to remove Media Center from Windows 8

  - by Arabella

  I bought 2 Windows 8 upgrades, 1 for my PC and 1 for my notebook. I added Windows Media Center to my notebook using the free offer in November (side note: the key was emailed to me within 5 minutes, I see many people have been complaining that it takes a few days). Today I decided to add WMC to my PC as well, so I went onto the Microsoft website, same like last time, and I received the email within a few minutes. Once I added WMC, entered the key and the computer rebooted, my activation is now broken: This product key is already being used on another PC. Try a different key or buy a new one. After rereading the product key email, I realised that the WMC key was exactly the same as the one I had received in November for my notebook (I used the same email, i.e. my Microsoft account Outlook email, for both). I didn't think this would be a problem, as on Microsoft's feature pack page it states: ...is limited to five licenses per customer per promotion. So then I decided, I'll just remove WMC from my PC and go back to Windows 8 Pro. So I turned off the WMC feature, PC restarted, activation still broken because my key has been replaced. I then tried to activate it with my original Pro key. The error it gave was that this key cannot be used with this version of Windows, as it is now Windows 8 Pro with Media Center and not Windows 8 Pro anymore. I've searched a bit and it seems the only way to remove it is do a clean install. I tried the Windows 8 Downgrade Helper, which told me I was already running Win 8 Pro when I tried to downgrade, and that I was running Win 8 Pro with Media center when I tried the other option. To sum up: How do I remove Windows Media Center from Windows 8 Pro without having to do a clean install?

  Read the article

• Overriding RPM public key database

  - by pilcrow

  Can rpm be persuaded to import and fetch public keys from an arbitrary pubkey database? On the same build machine I've got two automated users who each need to verify package signatures from different sources, signed under different keys. If I rpm --import pkg-source1.pub pkg-source2.pub, each user will be able to verify packages intended for the other. I'd rather each user not know about the other's public keyring. Is there a way I can specify an alternate or supplementary pubkey database on a per-user or per-rpm(8)-invocation basis?

  Read the article

• Installing sphinx on a web hosting server

  - by fiftyeight

  I want to install sphinx search on a web-hosting server. I'm on a Linux VPS with hostgator, but I never actually installed anything on a remote server so this will be a first time for me. If there's anyone here who installed sphinx it's really help me I had some problems when using sphinx on my PC with the permissions and the MySQL files, eventually I got it working on my PC. Anyway, I'd me really grateful if anyone can help me with some questions Do i need root access to install sphinx? I have root access to the server but I'd connect to it as a normal user since doing stuff as root is always less secure. can anyone tell me by what user I need to execute the indexer and the search daemon? Should I use root access in order to this? when I did it as a normal user on my PC it gave me some trouble with the PID file and the log files. last time I executed the search deamon I executed it as a normal user and it gave me some trouble, I created the folder /var/log/ for log files and did chmod 777 on it, but still when I executed the search daemon it created the PID file "searchd.pid" file but with no permissions for some reason, any idea why? Thanx in advance. fiftyeight

  Read the article

• Why does Windows/Microsoft Updates always take such a long time to detect available updates?

  - by RLH

  It's a common task for many of us who work in any form of IT position using Windows. Eventually you have to install/re-install a version of Windows and what follows is a very long OS updating process. For a long time I have accepted the fact that this is a slow process and that's all there is to it. There is a lot to download, and some updates require restarts followed by further updates... Ugh! This morning I had to go through the process of installing Windows XP with SP3. I'm installing the OS on a VM on an SSD and I've been working on this thing for over 6 hours. Although, think there are many ways to knit-pick this process for improvements, there is one step that is always particularly slow and I can not figure out a good reason why. That step is the detection step on a manual update. Specifically, when navigate to the Windows (or Microsoft) Updates page, and then click the 'Custom' button to detect your updates. It appears that your PC just sits there for a painful amount of time. Check your Task Manager and it looks like your PC is, in fact, locked because your CPU isn't cooking but that's certainly not the case. Somethings happening but I have no clue what's going on? What is the updating software doing? If the registry was being searched, shouldn't my CPU usage peak? Does anybody know what's happening? I can loosely justify why some of the steps in the update process take so long. However, this one doesn't seem to have any reasoning.

  Read the article

• Getting Started in SuSE as an Ubuntu User

  - by Subhamoy Sengupta

  I am not a Linux newbie, but haven't touched SuSE in a very very long time (last time I tried it, it was SuSE 7!). Finally now I felt like giving it a try, and many things seem strange or unnecessarily complex. I have a series of questions. How do I ensure that my packages are uptodate? It sounds silly, but I tried the obvious methods already. I have disabled the default repositories that show up when you do zypper lr, and added Tumbleweed and packman repositories (Essentials, Multimedia, Extra). Then I did a sudo zypper ref --force and then sudo zypper dup, and it tells me many dependencies are not met. I have already added solder.allowVendorChange=true to /etc/zypp/zypp.conf, so it should not care which repository the latest versions are in, and just upgrade to it. Even when I chose to skip the packages with unmet dependencies, and seemed like quite a bit happened in the background, I opened Firefox afterwards and the version was 7! I am guessing things did not go as expected. But of course this is not a problem with SuSE, but I am not understanding the system right. How do I do it right? When I start typing arguments of a command, for example sudo zypper install, when I type sudo zypper ins and keep hitting TAB, nothing happens! It always worked in Ubuntu and I feel very uneasy with this. Is this how SuSE is supposed to be? When I try to install something, and I start writing its name, even though the package exists and I am sure of it, hitting TAB does not autocomplete it. This is also quite inconvenient. Why is it not happening? There are many things in SuSE that are really great, and I think I will stay with it and not go back to Ubuntu once I settle these very rudimentary issues. But right now they are giving me a lot of grief! Please help!

  Read the article

• ubuntu preseed installation keep missing mirror files

  - by JackWu

  Install ubuntu12.04.2 with preseed file, but there is one buggy problem about preseed mirror setting. The symptom here is installing process got stuck. So I track down the log file, and find out the real problem, the installation is looking for a file that's not there. This is just one of them, another pops up if I faked this file. This all happened during preseed, so I believe preseed has something to do with this. I google ubuntu preseed mirror and find this post saying: # If you select ftp, the mirror/country string does not need to be set. #d-i mirror/protocol string ftp d-i mirror/country string manual d-i mirror/http/hostname string archive.ubuntu.com d-i mirror/http/directory string /ubuntu d-i mirror/http/proxy string # Alternatively: by default, the installer uses CC.archive.ubuntu.com where # CC is the ISO-3166-2 code for the selected country. You can preseed this # so that it does so without asking. #d-i mirror/http/mirror select CC.archive.ubuntu.com # Suite to install. #d-i mirror/suite string lucid # Suite to use for loading installer components (optional). #d-i mirror/udeb/suite string lucid # Components to use for loading installer components (optional). #d-i mirror/udeb/components multiselect main, restricted I wonder the difference between d-i mirror/http/hostname and d-i mirror/http/mirror, I mean they all specify a mirror, right? In my preseed file, this is no d-i mirror/http/mirror, and d-i mirror/http/hostname points to my own repo as you might notice in the previous image. Here is my question: Does preseed fetches file/resource from internet, if I use local repo? Why it's looking for file that's not even there? This has bothered for quite time, many thanks in advance to anyone who might give any help.

  Read the article

• Reset rc.d so software starts at boot again

  - by natli

  I ran the following 2 commands on my VPS box and now it boots without starting any software at all. According to rcconf it's still supposed to start my chosen software (ssh etc.) but it doesn't. update-rc.d vz defaults update-rc.d vzeventd defaults I already tried removing them again with update-rc.d -f vz remove update-rc.d -f vzeventd remove But that didnt't change anything. /etc/rc.local also still correctly lists some scripts I want to run at start-up, but they don't seem to be called either. I expect the top 2 commands to be responsible, but here's everything I did: mkdir /var/openvz-dl cd /var/openvz-dl wget http://download.openvz.org/kernel/branches/rhel6-2.6.32/042stab062.2/vzkernel-2.6.32-042stab062.2.x86_64.rpm wget http://download.openvz.org/kernel/branches/rhel6-2.6.32/042stab062.2/vzkernel-devel-2.6.32-042stab062.2.x86_64.rpm wget http://download.openvz.org/utils/vzctl/4.0/vzctl-4.0-1.x86_64.rpm wget http://download.openvz.org/utils/vzctl/4.0/vzctl-core-4.0-1.x86_64.rpm wget http://download.openvz.org/utils/ploop/1.5/ploop-1.5-1.x86_64.rpm wget http://download.openvz.org/utils/ploop/1.5/ploop-lib-1.5-1.x86_64.rpm wget http://download.openvz.org/utils/vzquota/3.1/vzquota-3.1-1.x86_64.rpm apt-get install fakeroot alien fakeroot alien --to-deb --scripts --keep-version vz*.rpm ploop*.rpm dpkg -i vz*.deb ploop*.deb --force-overwrite update-rc.d vz defaults update-rc.d vzeventd defaults reboot A huge part of that failed because I was running it on an OpenVZ VPS which has a shared kernel that can't be altered, so I also had to fix the dpkg like so (it was moaning about wanting to install vzkernel with a package not being found); rm /var/lib/dpkg/info/vzkernel* dpkg-reconfigure vzkernel --force dpkg --purge --force-all vzkernel But that didn't fix the boot issue either. How do I make my software start at boot again?

  Read the article

< Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >