Search Results

Search found 16628 results on 666 pages for 'setup kit'.

Page 421/666 | < Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >

• USB 3.0 Device not detected in Windows 8

  - by Tek

  About my setup: Windows 8 64-bit. X79-UD3 Motherboard. Latest Windows 8 USB 3.0 Drivers from motherboard manufacturer website. All right so device manager detects my USB 3.0 ports, so all is well there. However when I plug in my external USB 3.0 hard drive, windows doesn't even make a beep; the hard drive is not picked up by device manager at all. The SAME thing happens with Ubuntu 12.10 BUT adding PCI=nomsi (as a workaround) to the Grub command line of the Ubuntu boot option makes Ubuntu 12.10 detect my external hard drive. I also have a few other doubts, if you guys would be kind enough to answer them that include: Should XHCI hand-off in the UEFI bios be enabled or disabled for Windows 8? The difference between XHCI hand-off and EHCI hand-off and what are it's effects on USB 3.0 functionality? And last but not least how can I get Windows 8 to recognize my external hard drive when Ubuntu 12.10 (after the Grub workaround) works fine?

  Read the article

• Tool to automate basic connectivity testing

  - by feicipet

  After our vendors have setup a certain test environment, we need to go in to perform connectivity testing between PC to servers and also between servers. The problem is that we run a range of tests to telnet between 2 nodes on several ports and this is a manual and rather tedious process. Does anyone know of a small tool or script that I can take input on the range of ports to be test and will run an automated range of testing against those ports? All I need to do is to validate whether a TCP connection can be established from the source PC / server to the target server IP address / port. Thanks, Wong

  Read the article

• How to prevent Windows 8 of erasing GRUB?

  - by dirleyrls

  I'm doing dualboot with Ubuntu and Windows 8 on my DELL Laptop. EFI is enabled, secure boot is not. My partitions are GPT. Everything seems to work for some time. After some normal use, GRUB stops working. The "ubuntu" EFI entry is still there on top of everything else. But the computer boots directly into the Windows Bootloader, skipping GRUB. Any clues on why is that happening or how can I prevent that? My current partiton setup is: - /dev/sda1 NTFS Windows recovery - /dev/sda2 FAT32 UEFI boot (with boot flag) - /dev/sda3 unknown (msftres flag) - /dev/sda4 NTFS Windows Drive C - /dev/sda5 ext4 /home - /dev/sda6 ext4 / I usually reinstall GRUB through chrooting from a Live Session and doing a apt-get install --reinstall grub-efi-amd64.

  Read the article

• Cleaning cruft from the stored configs database

  - by Zoredache

  I have setup stored configuration primarily as a method to manage my ssh known_hosts. Unfortunately as I retire hosts the old configs still exist in my database. The answer seems to be run the command puppet node clean <hostname>. The problem is that while this does command does run, and does clean up some data, it doesn't seem to clean up everything. For example I can still find values in the puppet_tags table that only applied to a hosts that no longer exists. What should I be doing to keep my stored configuration database clean of all extra junk that seems to be building up? P.S. Can anyone point me any documentation for the stored configuration schema?  If I could find good documentation, or at least an entity-relationship-diagram, I would be tempted to just do some manual clean-up.

  Read the article

• accessing external mysql server through "ssh tunnel" - any drawbacks?

  - by Max

  In an upcoming project I have a two server setup: one is the application server and another, already existing runs the mysql server with databases I need to access. I contacted the server admin of the mysql server and the only way I can access the remote mysql databases is via "SSH tunnel". I have never done this before and never heard of it so far, so my question, are there any drawbacks, e. g. performance wise? Isnt it rather slow compared to directly accessing the mysql server on its default port?

  Read the article

• USB-based AV application that restores compromised Windows files from CD/DVD?

  - by overtherainbow

  Hello I just tried a couple of rescue disks (AVG and Kaspersky), and I was wondering if someone knew of a solution that would work like this: The AV solution boots from a USB key, and works entirely from RAM (where the latest virus DB is downloaded) The user inserts his Windows CD/DVD in the drive If any Windows file is compromised, the AV application fetches a clean version from the CD/DVD and restores it on the hard drive optionally, any compromised drive/user-land application is quarantied, and it is up to the user to reinstall those after he successfully rebooted into a restored Windows setup Have you heard of a solution like this? It seems silly to reinstall a whole Windows computer just because one or a few system files were compromised. Thank you.

  Read the article

• SQL Server 2012 Express LocalDB &ndash; How to get started

  - by krislankford

  As many of you aware, SQL Server can be a bit of a pig when it comes to system resources on your development machine. As part of the 2012 products Microsoft has added SQL Server 2012 Express LocalDB which is a happy medium for myself when thinking about having to install a full blown SQL Server on my box. This however does not work in all cases for all development but if you are doing web or local client development then it should suffice. On the other hand, if you are working with technologies like SharePoint or trying to run Team Foundation Server on your local box then you will be out of luck while using LocalDB. To start of with, the localDB setup is delivered and packaged with Visual Studio 2012 RC. If you want to get the stand-alone installer you can download it here in either the 32 or 64 bit flavors. Once you get it installed you can start using it right away in either Visual Studio 2010 or the new Visual Studio 2012 RC. To get started you can open the SQL Server object explorer in Visual Studio by clicking   the menu option View –> SQL Server Object Explorer. This will bring up to the navigation pane where you can add a SQL Server. Once you add the SQL Server you will be prompted with the “Connect to Server” dialog to enter the server for which you can use “(localdb)\v11.0”. Click connect and you should be connected to your localDB where you can create and manage databases from Visual Studio 2010, Visual Studio 2012 or SSMS. Once you have started creating databases here you can use the database projects in Visual Studio with these database as well as use the (localdb)\v11.0 server name inside your connections string information for your development environment. Hope this helps someone get started with SQL Server 2012 Express LocalDB! It provides a great balance for developing against SQL Server 2012.

  Read the article

• Powering off sends me to "Launch Windows Repair" automatically instead! What do I do?

  - by Jason

  With Windows 2008 R2 Server, I noticed that if I remotely reboot the machine (because it is hung or I think it is hung), the server, when it restarts, defaults to "Launch Windows Repair" (or something similar) rather than "Start Windows Normally". To change it, I have to trek down to the server room and change the boot up otherwise it will go into an endless loop (because I don't have the setup media and DVD-ROM installed). This seems to be new with 2008 R2 because I have not seen it elsewhere. What do I do? How can I remove this or change the default?

  Read the article

• Cross Domain access of self hosted WCF services?

  - by Macnique

  I have developed a WPF application which communicates with a set of self hosted WCF services which are under same domain and I use the following setup in the config files. <security mode="Transport"> <transport clientCredentialType="Windows" protectionLevel="EncryptAndSign" /> <message clientCredentialType="Windows" /> </security> I hosted the services on a server in different domain .I can achieve the communication by setting the security mode to "None" which is not ideal. Is there any other setting i can user for cross domain communication or i have to do with some trusted certificates ? I would be glad if some one can guide me because all the searches on google directed me to silverlight applications +Crossdomain.xml+WCF but i have't seen any combination of WPF on crossdomain environment.

  Read the article

• how to reduce size (disk space) of windows 8?

  - by humanityANDpeace

  This questions is about what things I can do to reduce the size that Windows 8 uses. Background For example: At present and with only one programm installed (MS Access 2007) I have a about 15GB of my harddisk space used. I have little space (its a 17 GB partition on a SSD disk). I would like solutions that are like: Remove files not really needed (drivers not actually needed in the system) Help files not really needed (documentation) pagefile.sys (assuming I would have 4GB ram and no real need for swaping) hiberfil.sys (used for hibernate and sleep... I need that. though I would regain about 4GB space) At best I would like to delete mostly files that I would most likely not need. Though I have no good idea where to start there. Since my setup (hardware will not change) I would be willing to delete all the drivers that windows 8 has for hardware I do not have.... The question is about ways to reduce the space that Windows 8 uses.

  Read the article

• How do I get transparent, efficient, file system snapshotting or versioning on ext3/4?

  - by shovas

  I've long thought about versioning file systems. This is a killer feature and I've looked at Wayback, ext3cow, zfs, fuse solutions, or just cvs/svn/git overlays. I consider ext3cow the model for my requirements. Transparent, efficient, but I can do without the extra ls abc@timestamp feature. As long as I somehow get automated, transparent versioning of my files. It could be instantaneous or it could be based on snapshots on intervals of 10s, 30s, 1m, 5m, 15m, etc. Just something that will efficiently deal with thousands of files in a given directory all of various sizes, most small, but some upwards of 100m to 1gb. ZFS isn't really an option as I'm on linux (and would prefer not to use it through fuse as I already have an ext3 setup I want to version, not something new). What solutions are out there?

  Read the article

• Can one use Airport (Time Capsule) with an external DHCP server?

  - by DNS

  I currently share my DSL connection using a wireless router with DHCP disabled, and dnsmasq running on a Mac Mini serving DHCP & DNS. This setup is important because I have clients doing PXE boot, and I need the control over DHCP that dnsmasq provides. There is also a Time Capsule on the network that's used purely as a backup device; its wireless functions are disabled. The wireless router is starting to get a little flaky, and since it doesn't support 802.11n I'd like to replace it. Rather than buying a new router, I'd like to just use the Time Capsule. But I see no way to disable its DHCP server; when I set the connection type to PPPoE, it insists on serving DHCP. Is there any way to use Airport PPPoE with a DHCP server elsewhere on the network?

  Read the article

• Masquerade traffic from certain source IP to VPN connection

  - by Shuo Ran

  Network Setup: 10.0.0.1 Router: to internet 10.0.0.70 Server: Ubuntu based server,default gateway is 10.0.0.1 10.0.0.51 PC I created a PPTP connection(interface: ppp0) on Server to a machine on the internet, what I want to do is route all the traffic from certain IP address(10.0.0.51) through the PPTP connection and then to the internet. What I did are: Set the gateway on PC(10.0.0.51) as 10.0.0.70 Enabled ipv4 forward on 10,0,0,70 Add the masquerade rule to iptable: iptables -t nat -A POSTROUTING -o ppp0 -s 10.0.0.51 -j MASQUERADE After that, it seems none of the traffic from 10.0.0.51 be redirected to ppp0, instead these traffic are still going through 10.0.0.1 directly. Any thoughts on it?

  Read the article

• sa2 -A /var/log/sa/sa13: No such file or directory

  - by user53925

  I have systat version 7.0.2 and the /etc/sysconfig/sysstat has the entry HISTORY=27, this is on a redhat enterprise server 5.6, the cron setup for this is # run system activity accounting tool every minute * * * * * root /usr/lib64/sa/sa1 1 1 # generate a daily summary of process accounting at 23:53 53 23 * * * root /usr/lib64/sa/sa2 -A I get the following error from the cron sa2 -A find: /var/log/sa/sa13: No such file or directory, Looking at the directory /var/log/sa the files are created from sa01 through sa10 (sa1 created on sep1, sa2 created on sep2 and so on), then the rest of the files are from sa14 through to sa 31 (created from Aug 14 to Aug 31). I have not made any changes on the server so I am not sure why I am getting these error messages and is there a way to fix this?. Someone suggested creating empty files from sa11 through sa14 to fix this but I am not sure if this might mess up something .

  Read the article

• Cannot log-in in the install of phpmyadmin on Ubuntu

  - by Sylario

  I just installed phpmyadmin and i am trying to login in /phpmyadminpath/setup. I am greeted by an invite similar to an apache protected folder (log/password displayed in a browser pop-up, not an html popup) asking for login pass. I cannot login using system password(root) or mysql passsword(also root) I already have rails app using this mysql, and i checked the mysql password in the config files. I cannot run any mysql command in my console because of the following error : ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: NO) What is wrong with phpmyadmin and mysql?

  Read the article

• Debian SMB share having permission issues in windows 7

  - by xxpor

  Hi Everyone, I setup a Debian squeeze server with samba. I then shared my /media directory with the following configuration: [media] comment=Hard Drives read only = no locking = no path = /media guest ok = yes browsable = yes directory mask = 0777 When the drives are mapped in Windows 7, the user can write to all of the subdirectories of media (sdb1, sdc1, etc), but cannot write to any folders that they create themselves in the subdirectories of media. For example, if the user mapped /media/sdb1 to Z:, and then creates a folder Z:\test, the folder is created successfully, but no files can be written to Z:\test. If the user ssh's into the server, they have no problems writing to these directories. I have included the screenshots, in order, of what happens on Windows. This samba share is mounted with ntfs-3g, if it makes a difference. Screenshots are here

  Read the article

• Should the virtualization host be allowed to run any service?

  - by Giordano

  I recently setup a virtualization server for the small company I'm running. This server runs few virtual machines that are used for development, testing, etc... My business partner works from a remote location, thus I also installed a vpn server on the virtualization host to make it possible for him to safely reach the company services. Moreover, again on the virtualization host, I installed bacula to perform the backup of the data. Is it advisable/good practice to do so or should I create one more virtual machine to do backups and VPN? Is it a bad idea to run these services on the host itself? If yes, why? Thanks in advance!

  Read the article

• redundant http load balancer

  - by jrydberg

  Got a simple scenario with two web servers for redundancy and to scale. But how do I make a two web-server setup fully redundant? I can think of two solutions; two web servers, one load balancer spreading the load. one extra machine for the load balancer. but how will the load balancer be redundant? two machines, each running the web server AND running a load balancer, spreading the load over. have a DNS entry point to both of the machines. no extra machines needed for load balancing. How do you guys normally solve this kind of problem?

  Read the article

• openvpn and selective routing

  - by mx2323

  hi everyone, whats the best way to configure openvpn clients to go selectively go about using an openvpn connection? i want to setup a vpn server for friends in china, but i dont want them to use it for everything, just so they can access sites like youtube, facebook, cnn, etc. while they are in china through the vpn (these are blocked). it would be nice if the vpn was a backup, so for instance if they are trying to go to facebook (which is blocked), it would go through the vpn connection once finding that the normal connection does not work. this would save a lot of bandwidth cost actually, and give them a better browsing experience. is this a iptable route thing? or a dns server that i push to my clients?

  Read the article

• How do you host images using Windows Server so that they are accessible over the internet? [closed]

  - by nairware

  I was trying to figure out a way to host images (picture images, not disk images) such that they are accessible over the internet via URLs--in a way similar to a web service like Photobucket or ImageShack. I have a whole bunch of Windows Servers (Windows Server 2008 R2) available in the cloud. Instead of hosting images using Photobucket or ImageShack, I wanted to host this images directly on my own Windows cloud. This could be really complicated or really simple. I have no idea, as I know very little about IIS 6 (which is what I am using) or web servers. If this is too broad of a question (as there are probably multiple ways of implementing this), is there at least some guide or documentation of how someone else has setup image hosting? Perhaps a step-by-step guide of at least one way to do it?

  Read the article

• How do I set up a working GUEST USER account in Win XP Pro?

  - by user6501

  I have two user accounts within my WinXP Pro PC. One I'd like to erase. But I'd also like to setup a GUEST user account. I've already gotten 2-step instructions on how to get rid of the extraneous account: a) use an MS tool called delprof.msi b) manually delete the former users files in Documents & Settings. But I guess my original question was too complex -- kind of like a bill in Congress. So now I am just asking the final part of the question: How do I create a GUEST ACCOUNT -- then define what it will authorize/grant access to? i.e. internet browser(s), specific programs and files etc

  Read the article

• How to set a character set per application in *nix?

  - by SimmaDoWN

  I am attempting to set a character set of IBM850 on slackware linux for a particular application (epic5). Im using rxvt-unicode and have setup LANG/LC_*=en_US. Now if I set the encoding to IBM850 in kde's konsole program im able to display certain characters correctly. I'd rather not use IBM850 for everything; is there a way to set/alias a command for a per application execution? Ive tried things like: LC_CTYPE=IBM850 epic5 LC_ALL=IBM850 epic5 No success. Any help would be appreciated

  Read the article

• Cannot access apache webserver running on home network from internet.

  - by user60382

  I am trying to setup apache web server in my home network. I followed the instructions found at http://www.boutell.com/newfaq/creating/hostmyown.html. I have a d-link dir-601 router with a cable internet connection. I am able to connect to the web server from my LAN using the url pointing to my server's ip 192.168.0.103 in the web browser. but when I am trying to browse the same with my phone on 3G network, I get a message "server cannot be found". My Public IP starts with 61.xx.xxx.xxx and my router has an IP of 192.168.0.1 Could anyone please help me in figuring out the isuue. Thanks in advance.

  Read the article

• Can i use a Windows 2008 r2 Cluster for file redundancy

  - by JERiv

  I'm researching a sever clustering architecture as a redundancy and backup solution for a client, and something that isn't made clear is whether or not i can use server clustering to replace a file server with backup solution. Forgive my Elementary understanding of server clustering but supposing: 2 Sites (NJ, CA) Identical Servers at each site setup as a Remote Site Cluster nodes with Windows Enterprise server 2008 r2 Services: File, Terminal, AD, and maybe DNS Will the following will be true: Files (including data drives) will be synced between the two servers eliminating the need for third party backup/mirroring software to sync/backup files. Also supposing i use roaming profiles w/ folder redirection; How will client computer in the WAN access their data through the cluster (i.e. will they automatically choose the best route)

  Read the article

• Services of virtual machines

  - by RredCat

  I am looking a way to establish dev machine on the cloud. I want to have access for development from different places. I don't want to play with sync brunch and so on. It would be Lubuntu with 1G or 512M memory and I want to have way to setup my image. What I have found in the current moment: Amazon EC2 service Azure Virtual Machines I am pretty sure that there should be more services like this. I hope to find one specified for this purpose. I have experience to work in such way and I like it. Unfortunately it was server of certain company for projects of this company and I can't use it for my private aims. Could anybody suggest me anything?

  Read the article

< Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >