Search Results

Search found 10827 results on 434 pages for 'spring boot'.

Page 421/434 | < Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >

  • Network Services disabled (not starting) on Windows XP

    - by Rickesh John
    I am currently running Windows XP Service Pack 3 on my system. But today, when I failed to connect to the internet, via a LAN cable, I realized that almost all of the vital network services had stopped functioning. Any attempts to start it through services.msc gives me the following message: Could not start the DNS Client Service on Local Computer Error 1068: The dependency service group failed to start All my software or services that are related to networking have stopped functioning, for example, Windows Firewall is turned off permanently, so is my Avast Anti-Virus' service of Real Time Shields and Web Shield. When I insert the LAN wire into my laptop, it registers itself, but this is what I get when I do a ping localhost C:>ping localhost Unable to contact IP driver, error code 2 Moveover, with ipconfig I get this : Windows IP Configuration An internal error occurred: The request is not supported. Please contact Microsoft Product Support Services for further help. Additional Information: Unable to query host name On some further poking around, I saw that none of the "NETWORK SERVICE" process in task manager, except svchost.exe were running. Also, when I first opened the task manager, I saw some 20 processes running with username column empty for most of them. With some search in Google, I found out that these services were important, DHCP DNS Net logon Network connection Network location Awareness TCP/IP Net BIOS Helper none of them, except Network Connections are working, they do not start. The event viewer of my system shows a bunch of 7000 and 7001 event errors. I have tried re installing the network driver, booting in safe mode with networking and tried to enable those services mentioned above. I had disabled System Restore some time back, so I have no restore points for my system. I tried a lot of things from Google searches but none of them worked. Also, with such a long list of issue, I am a little confused as to what should I search on the internet. :( One more thing I would like to mention, previous morning, my anti-virus Avast detected a RootKit buried deep in my system folders. It was removed, but maybe this was a problem caused by the root kit. I did run a boot-time scan but no viruses were found. Please please please advice. Is formatting and re-installation of Windows my only option?

    Read the article

  • How to remove RAID flag on unstriped drive without losing data?

    - by Alex Folland
    I have a Gigabyte Z68X-UD4-B3 motherboard. It advertises this new thing called "XHD", which is like RAID but makes a SSD and traditional-style drive work together to enable high speed with high capacity. I don't want to use this feature, and I already have Windows 7 64 installed without using this feature. When I first installed my 2 hard drives (1 SSD and 1 traditional-style drive) in my machine and booted it up for the first time, it ran a program from the mobo that asked me if I wanted to set up XHD. Thinking it would go to some config screen, I said yes. It immediately started doing something with my drives and finished. I considered that strange, but figured it wouldn't matter when I simply install Windows onto my SSD only. I now have my BIOS and Windows running in AHCI mode with no RAID arrays and separate drives. My SSD is one of those new Corsair Force GT drives which loses power every so often, causing Windows to BSOD. I've figured everything out about this problem, including installing the latest firmware from Corsair, and the only way to fix it at this point is by installing Intel Rapid Storage Technology to control AHCI instead of Windows, since the Windows AHCI driver disables the drive's power every once in a while and can't be configured not to do so. I've tried installing Intel Rapid Storage Technology. When I reboot my machine after doing so, it BSODs just after the Windows logo. I've figured out this is because my SSD and my traditional drive are flagged as RAID, as seen in the "Intel Matrix Storage Manager" program found by switching the BIOS hard drive handling to "RAID" mode. This is due to the XHD auto-config program I mentioned earlier. Normally, the BIOS is set to AHCI, and when the drives boot in AHCI mode, they work perfectly. So, I've concluded the data is stored in AHCI mode but the drives' flags are set to RAID. I've figured out that I can accomplish my objective by using the "Intel Matrix Storage Manager" program on the mobo (with "Reset disks to non-RAID"), but doing so would cause it to completely wipe the drives I select. I want to simply toggle these flags from RAID to AHCI so Intel Rapid Storage Technology doesn't fail and cause a BSOD upon booting, but without wiping the drives.

    Read the article

  • All internet requests in Windows time out

    - by Brandon
    So, I've run into a very strange problem with my home wireless network. Previously, at seemingly random times, the router seemed to disconnect all wireless hosts and cause all of the wired hosts to have a "limited connection" according to windows. In order to fix this, I had to unplug all of the wired hosts from the router, unplug the modem from the router, and power cycle the router. This seemed to solve the problem for a while until the exact same thing happened a day later and I had to go through the same process again. That's where I noticed something weird happening. There was one wireless host (a Windows Vista laptop) that seemed to be causing the router to disconnect the other hosts whenever it connected. When this happened, only that laptop was able to use the wireless from the router. When this happened, I disconnected it from the wireless (by disabling the wireless adapter) then reconnected it (by re-enabling it) and now it, like the other hosts, couldn't connect. I've never really seen anything this strange happen on our network before. So, I restored the router to factory settings and the problem seems to have vanished except one crucial problem. There's another host (a Windows 7 laptop) that was perfectly able to connect before all of the router issues and even in between the crashing and power-cycling events but now says its connected and says it's able to reach the Internet, but all requests time out. In any browser I've tried, the tab says connecting to [site]... for a solid minute and then tells me the request timed out. When I try to ping google.com in cmd it also says request timed out. In frustration, I booted into a dual-boot Ubuntu installation on the Windows 7 host and the connection works fine, to my surprise, as ubuntu is where I am now typing this rather long question. I haven't looked through the event log in windows but will post anything I find in an edit I haven't tried connecting (in Windows 7) to any other wireless network, since The fact that it works in Ubuntu suggests its Windows and not the router but I didn't change any wireless settings in windows before it being able to reach the Internet and not. Does anyone have any clue what could have happened. I opened to buying another router as this one is almost a year old :) but I would like to know whats going on here. Thanks in Advance! P.S. Sorry for how long my question is, I'm a little anxious (:

    Read the article

  • Logitech Optical Mouse Frozen In Middle of Windows XP Pro Screen

    - by Code Sherpa
    Hi. I have a Logitech Optical Mouse/Keyboard. I have been using them just fine with the system drivers for almost a year now. I recently updated my Kaspersky software and rebooted. Now the mouse is frozen in the middle of my screen. I am not able to login to the Windows XP Pro box that has the frozen mouse (because i can't work the mouse) but am able to remote desktop to this computer. Things I know / have tried: When I boot on the problem computer, I am able to use the keyboard, but not the mouse. I have installed the latest version of Logitech's SetPoint (with the updated drivers) on the problem computer (via remote desktop) and that didn't seem to matter. I bought new batteries for the mouse and that didn't matter. I have tried the mouse/keyboard on another computer and the mouse works just fine there. My suspicion is that the Kaspersky install has overwritten a driver of some sort. Things I have not done (and would appreciate detailed steps if you feel this is the way to go): 1) Uninstalled all the mouse drivers on the machine and reboot. Then, reinstall. Note: When I get to the Device Manager I don't see an option for Human Interface Devices (where the mouse device is). Here are my options: Computer, Disk Drives, DVD/CD-Rom drives, Floppy controllers, IDE ATA/ATAPI, Imaging devices, Network Adapters, Other devices, Ports, Processors, Sound, video, and gaming, System devices, USB controllers. Also, I should point out that Video Controller is the only thing under Other devices and it has a yellow exclamation mark. The same is true for all the items under Universal Serial Bus controllers. I think this means I have to update my BIOS but, since my mouse was working just fine without doing that, I don't think that is my problem. So, how do I get to my Mouse Device? 2) Update my BIOS. Note: As pointed out above, I don't think this matters as my mouse was working just fine under my computer's current BIOS version. Thanks for your help.

    Read the article

  • Linux Best Practices

    - by Zac
    I'm a life-long Windows developer switching over to Linux for the first time, and I'm starting off with Ubuntu to ease the learning curve. My new laptop will primarily be a development machine: 6GB RAM, 320 GB HD. I'd like there to be 2 non-root users: (a) Development, which will always be me, and (b) Guest, for anyone else. I assume the root user is added by default, like System Administrator in Windows. (1) I'd like to mount /home to its own partition, but how does this work if I have two user accounts (Development and Guest)? Are there 2 separate /home directories, or do they get shared? Is it possible to allocate more space for Development and only a tiny bit of space for Guest in GRUB2? How?!?! (2) I'm assuming that its okay that all of my development tools (Eclipse & plugins, SVN, JUnit, ant, etc.) and Java will end up getting installed in non-/home directories such as /usr and /opt, but that my Eclipse/SVN workspace will live under my /home directory on a separate partition... any problems, issues, concerns with that? (3) As far as partitioning schemes, nothing too complicated, but not plain Jane either: Boot Partition, 512 MB, in case I want to install other OSes Ubuntu & non-/home file system, 187.5 GB Swap Partition, 12 GB = RAM x 2 /home Partition, 120 GB I don't have any bulky media data (I don't have music or video libraries, this is a lean and mean dev machine) so having 320 GB is like winning the lottery and not knowing what to do with all this space. I figured I'd give a little extra space to the OS/FS partition since I'll be running JEE containers locally and doing a lot of file IO, logging and other memory-instensive operations. Any issues, problems, concerns, suggestions? (4) I was thinking about using ext4; seems to have good filestamping without any space ceiling for me to hit. Any other suggestions for a dev machine? (5) I read somewhere that you need to be careful when you install software as the root user, but I can't remember why. What general caveats do I need to be aware of when doing things (installing packages, making system configurations, etc.) as root vs "Development" user? Thanks!

    Read the article

  • Create and manage child name servers (glue records) within my domain?

    - by basilmir
    Preface I use a top level domain provider that only allows me to add "normal" third-party name servers (a list where i can add "ns1.hostingcompany.com" type entries... nothing else) AND "child name servers" which i can later attach to my parent account ( ns1.myowndomain.com and an ip address). They do not provide other means of linking up. I want to host my own server and dns, even with just one name server (at first). My setup: Airport Extreme - get's a static ip address from my ISP Mac Mini Server - sits behind the Airport and get's a 10.0.1.2 My problem is that i can't seem to configure DNS correctly. I added a "child nameserver" with my airport's external static ip address at the top level provider, so to my understanding i should have all DNS traffic redirected to my Airport. I've opened port 53 UDP to let the traffic in. Now, what i don't get is this. My Mini Server is sitting on a 10.0.1.2 address and i have setup dns correctly, with an A record to point and resolve my server AND a reverse lookup to that 10.0.1.2. So it's ok for "internal stuff". Here is the clicker... How, when a request comes from the exterior for a reverse lookup, does the server "know" ... well look i have everything in 10.0.1.2 but the guy outside needs something from my real address. I can't begin to describe the MX record bonanza... How do i set this "right"? Do i "need" my Mini Server to sit on the external address directly (i can see how this could be the preferred solution, being close to a "real" server i have in my mind). If not... do i need a PTR record on the 10.0.1.2 server but with the external address in there? My dream: I will extend this "setup" with multiple Mini's in different cities where i work. I want a distributed something (Xgrid comes to mind). PS. Be gentle, i've read 2 books and the subject, and bought both the Lynda Essentials and DNS and Networking to boot, still i'm far from being on top of things.

    Read the article

  • Windows 7 reboot and freezing, possible power problems?

    - by mikelbring
    My Gateway LX Series desktop is about 6-8 months old. When I bought it, it had Windows Vista. I then put the RC version of Windows 7 on it. About 3 months after I bought it, it would randomly start to reboot, actually just shut off. I monitored the temperature levels and they seemed normal. So I installed a fresh Windows 7 Ultimate OEM 64bit. It actually got worse and would reboot more frequently. I then contacted Gateway and they said my machine was built for Windows Vista (made me chuckle), and told me to update my BIOS. So I did, and it was fixed for a good couple months. Recently, it started to do it again. Now I noticed early on it was doing it most often, if not every time when I was either watching a flash video or playing a flash game. So I decided to download the drivers again and I also downloaded my motherboard drivers. Seemed to be okay. A week later it started doing it again. And now it's doing it even more frequently. Sometimes I would turn it on, login into Windows and *BAM!* it would shut off. Now I am at the point where I can hardly get it to turn on. It would freeze at the point where it says "Starting Windows", with the Windows logo. Sometimes it would say "Checking disk for consistency" or whatever and freeze there (not shut off, just freeze). I even got the prompt to launch startup repair. But that also freezes when it says starting Windows. It does not really freeze, just never loads up. I am kind of lost as to what's going on. I have a few ideas but nothing I want to pursue (graphics card? hard drive?). Another thing I did try was to boot into a live disk of Ubuntu and try to launch every program I could and get on the internet but I never got it to reboot. So it sounds like to me it's a Windows thing, but I have no idea. I am just stuck and would like to see if any one has any ideas or could lead me in the right direction.

    Read the article

  • Triple monitor setup in linux

    - by Brendan Abel
    I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

    Read the article

  • USB hard drive not recognized

    - by user318772
    Until recently I was using the portable USB hard drive in my win 7 laptop and ubuntu laptop. Suddenly now none of the laptops recognize it. This is the message i get by doing lsusb... Bus 001 Device 004: ID 1058:1010 Western Digital Technologies, Inc. Elements External HDD Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 0b97:7762 O2 Micro, Inc. Oz776 SmartCard Reader Bus 003 Device 002: ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 Hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub fdisk doesn't show the external hard drive Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004a743 Device Boot Start End Blocks Id System /dev/sda1 * 2048 152111103 76054528 83 Linux /dev/sda2 152113150 156301311 2094081 5 Extended /dev/sda5 152113152 156301311 2094080 82 Linux swap / Solaris when i do testdisk TestDisk 6.14, Data Recovery Utility, July 2013 Christophe GRENIER <[email protected]> http://www.cgsecurity.org TestDisk is free software, and comes with ABSOLUTELY NO WARRANTY. Select a media (use Arrow keys, then press Enter): >Disk /dev/sda - 80 GB / 74 GiB - ST980825AS Disk /dev/sdb - 2199 GB / 2048 GiB testdisk-> Intel->analyse I get partition error Disk /dev/sdb - 2199 GB / 2048 GiB - CHS 2097152 64 32 Current partition structure: Partition Start End Size in sectors Partition: Read error Here is the output of dmesg [11948.549171] Add. Sense: Invalid command operation code [11948.549177] sd 2:0:0:0: [sdb] CDB: [11948.549181] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.550489] sd 2:0:0:0: [sdb] Invalid command failure [11948.550495] sd 2:0:0:0: [sdb] [11948.550499] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.550505] sd 2:0:0:0: [sdb] [11948.550508] Sense Key : Illegal Request [current] [11948.550514] Info fld=0x0 [11948.550519] sd 2:0:0:0: [sdb] [11948.550525] Add. Sense: Invalid command operation code [11948.550531] sd 2:0:0:0: [sdb] CDB: [11948.550534] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.551870] sd 2:0:0:0: [sdb] Invalid command failure [11948.551876] sd 2:0:0:0: [sdb] [11948.551880] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.551885] sd 2:0:0:0: [sdb] [11948.551888] Sense Key : Illegal Request [current] [11948.551895] Info fld=0x0 [11948.551900] sd 2:0:0:0: [sdb] [11948.551905] Add. Sense: Invalid command operation code [11948.551911] sd 2:0:0:0: [sdb] CDB: [11948.551914] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 If possible i want to retrive at least some data from this hard drive. If thats not possible I would like to format it and use it. Any help will be greatly appreciated Thanks

    Read the article

  • Creating a fallback error page for nginx when root directory does not exist

    - by Ruirize
    I have set up an any-domain config on my nginx server - to reduce the amount of work needed when I open a new site/domain. This config allows me to simply create a folder in /usr/share/nginx/sites/ with the name of the domain/subdomain and then it just works.™ server { # Catch all domains starting with only "www." and boot them to non "www." domain. listen 80; server_name ~^www\.(.*)$; return 301 $scheme://$1$request_uri; } server { # Catch all domains that do not start with "www." listen 80; server_name ~^(?!www\.).+; client_max_body_size 20M; # Send all requests to the appropriate host root /usr/share/nginx/sites/$host; index index.html index.htm index.php; location / { try_files $uri $uri/ =404; } recursive_error_pages on; error_page 400 /errorpages/error.php?e=400&u=$uri&h=$host&s=$scheme; error_page 401 /errorpages/error.php?e=401&u=$uri&h=$host&s=$scheme; error_page 403 /errorpages/error.php?e=403&u=$uri&h=$host&s=$scheme; error_page 404 /errorpages/error.php?e=404&u=$uri&h=$host&s=$scheme; error_page 418 /errorpages/error.php?e=418&u=$uri&h=$host&s=$scheme; error_page 500 /errorpages/error.php?e=500&u=$uri&h=$host&s=$scheme; error_page 501 /errorpages/error.php?e=501&u=$uri&h=$host&s=$scheme; error_page 503 /errorpages/error.php?e=503&u=$uri&h=$host&s=$scheme; error_page 504 /errorpages/error.php?e=504&u=$uri&h=$host&s=$scheme; location ~ \.(php|html) { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_intercept_errors on; } } However there is one issue that I'd like to resolve, and that is when a domain that doesn't have a folder in the sites directory, nginx throws an internal 500 error page because it cannot redirect to /errorpages/error.php as it doesn't exist. How can I create a fallback error page that will catch these failed requests?

    Read the article

  • Detection of battery status totally messed up

    - by Faabiioo
    I already posted this question in the Ubuntu forum and stackOverflow. I forward it here with the hope to find some different opinions about the problem. I have an Acer TravelMate 5730, which is 3 y.o., running Ubuntu 10.04 LTS. One year ago I changed the battery because the old one died. Since then, everything worked like a charm. A week ago I was using my laptop running on battery; it was charged up to 60%. Suddenly it shut down and for about 24h it was like the battery was totally broken: it didn't charge anymore and the 'upower --dump' said state: critical. I was kind of resigned to buy a new battery, when suddenly the orange light became green: battery was charged and actually working; strangely the battery indicator was stuck to 100%, even after 2 hours running. I tried again with 'upower --dump' or 'acpi -b' commands and it kept saying battery is discharging, though maintaining the percentage to 100%. Thus, battery working fine up to 3 hours, without any warning when it was almost empty, likely to result in a brute shut down. Today something different. the 'upower --dump' command says: ... present: yes rechargeable: yes state: fully-charged energy: 0 Wh energy-empty: 0 Wh energy-full: 65.12 Wh energy-full-design: 65.12 Wh energy-rate: 0 W voltage: 14.481 V percentage: 0% capacity: 100% technology: lithium-ion I tried to boot WinXP and the problem is pretty much the same, with the battery fully-charged, percentage equal to 0% and no way to fix it. While writing, the situation has changed again: present: yes rechargeable: yes state: charging energy: 0 Wh energy-empty: 0 Wh energy-full: 65.12 Wh energy-full-design: 65.12 Wh energy-rate: 0 W voltage: 14.474 V percentage: 0% capacity: 100% technology: lithium-ion ...charging, but it does not charge up. (Recall, the battery lasted 3 hours until yesterday!). So, the big question is: is it an hardware issue, like a dedicated internal circuit is broken? or maybe it is just the battery that must be changed. Or, rather, some BIOS problem that could be fixed in some way. I'd appreciate every help that can shed some light on this annoying problem thanks

    Read the article

  • Concerning persistence size in the Linux Live Creator

    - by user63085
    Message : Hello everyone! I have ,for the last several months, used the Linux Live USB Creator which it is a very useful app to make portable OS on to flash drives. I mostly use this application to test and try out new OS's as they are released, before I decide to make a hard disk installatio on to the computer. In many cases, the application developers will allow the “persistence” feature in the flash-drive-installed OS, which is just another way of saying that after multiple boot-ups and shutdowns, all the changes made to the OS will be saved in the flash-drive. But I have a question about the limit of the Persistence size in Linux Live USB Creator (currently version 2.6). I install Super OS 10 on to a partition on my external drive which has 30 GB. I wanted to reserve 10 GB for the persistence so that I can install more applications and space will not run out as I update the installed applications or when I do system updates. But why is it that only 3950 MB can be put for persistence? It would be great if, when desired, as much more persistence space could be set aside so that the space will not run out soon. Also, as I have installed the OS on a 30 GB drive, I tried to see how much space is left. But it seems only the remaining of the Persistence space is displayed when I click on the File System folder. For example, after I have just installed it now, there is 3.5 GB of free space. Where can I access the remaining 26 GB or so drive space which is in the same drive? How do I access it Sir?? It would be helpful if any one could explain and help me with this. Most importantly, it would be a big relief if the persistence can be somehow expanded by a work-around so that I can continue using my SuperOS 10.04 (now heavily customized) OS, which unfortunately has just over 576 MB of space left now, after I removed OpenOffice.org and installed the Libre Office earlier today. This is what remains from the maximum allowable 3950 MB of space for persistence at set-up. Thanks in advance!

    Read the article

  • vmdk to live cd - VMware vmxnet virtual NIC driver Kernel panic

    - by ronalchn
    Task I am trying to convert a virtual machine to a live CD. Specifically, the virtual machine I am trying to convert is the IOI 2013 Competition Environment. In this task, I am aided by a guide Converting a virtual disk image: VDI or VMDK to an ISO you can distribute. Symptoms However, after getting through all the instructions, the live CD causes a kernel panic on boot on bare metal. In particular, the screen shows: [0.737348] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.737503] sr 3:0:0:0: >Attached scsi CD-ROM sr0 [0.737638] sr 3:0:0:0: >Attached scsi generic sg2 type 5 [0.737771] Freeing unused kernel memory: 756k freed [0.738093] Write protecting the kernel text: 5960k [0.738155] Write protecting the kernel read-only data: 2424k [0.738224] NX-protecting the kernel data: 4280k Loading, please wait... [0.752252] udevd[100]: starting version 175 [0.768708] VMware vmxnet3 virtual NIC driver - version 1.1.29.0-k-NAPI [0.781204] VMware PVSCSI driver - version 1.0.2.0-k [0.789555] VMware vmxnet virtual NIC driver [0.799356] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [0.799356] [0.799472] Pid: 1, comm: init Tainted: G 0 3.5.0-17-generic #28-Ubuntu [0.799549] Call Trace: [0.799603] [<c15bf0ec>] panic+0x81/0x17b [0.799654] [<c104a6a5>] do_exit+0x745/0x7a0 [0.799707] [<c104a9a4>] do_group_exit+0x34/0xa0 [0.799760] [<c104aa28>] sys_exit_group+0x18/0x20 [0.799813] [<c15cff5f>] sysenter_do_call+0x12/0x28 Possible problem I suspect that the problem is the VMware vmxnet virtual NIC driver - however, I do not know how I can uninstall it, and possibly install one for a bare metal machine. If anyone knows which packages needs installing/uninstalling at the .rootfs/ chroot directory stage, please let me know. Details on procedure Do note that after importing the .ova file into Virtualbox, the virtual machine is stored as a .vmdk file already, and not a .vdi file. I would like to point out some results of the procedure followed in case of any questions. This is after extracting the filesystem from the .raw file to the .rootfs/ directory mentioned in the blog. I changed the filesystem table as mentioned in the blog, then looked at the possible "kernel optimized for virtualization". However, I found that linux-image-generic was already installed. Also, when running the command dpkg-query --showformat='${Package}\n' -W 'vmware-tools*' (or dpkg-query --showformat='${Package}\n' -W '*-virtual'), no packages were found. Thus, I did not find any virtualization specific packages. I proceeded to generate the iso following the steps in the blog, and burned it to a DVD.

    Read the article

  • Computer randomly reboots during "intensive activity".

    - by Reznor
    My friend has been playing games on his new build for some time now. However, lately, his computer will randomly reboot out of nowhere, so far only happening in game, and presumably only to happen in game as it happens nowhere else. This can happen in game during play or even in the options. Note, it isn't a crash or blue screen. It's just a normal reboot. This started today, I believe, and has only occured in two games: Dead Space and Stalker: Shadow of Chernobyl. He has played a handful of games before these, for about a week or so, without this problem. We theorized on two possibilities: Maybe something is overheating? Maybe the power supply is inadequate? These two were quickly dismissed, as all his components were operating at normal temperatures when he got back to his desktop from the reboot, and we all know these parts don't exactly cool down quickly, especially if they get hot enough to trigger a reboot. Besides, I know at-least my motherboard reports processor overheating at start-up, and requests I press f1 to continue into boot. The PSU one was dismissed too. He has an 850w power supply on a rig that was estimated to take only 720 some watts, that's with some overcompensating to be safe. He opened up his case to make sure nothing was seated wrong or in the way. All was fine, but he did notice a sticker on his video card. It had a giant barcode on it and some numbers. Now, I'm used to seeing these stickers, they're the warranty stickers, right, and removal voids the warranty? Yeah, well, we find it odd because this sticker is slapped right over the circuits of the video card, not on a block or anything. Is this normal? Should he remove it? Right now, I am concerned with the memory. Could that be at fault? Here are his specs: Windows 7 Home Premium, 64-Bit Intel i7 950 EVGA GeForce 570 GTX 4 GB DDR3 PC10666 dual-channel Corsair RAM Corsair 850w PSU Gigabyte GA-X58A-UD3R Western Digital 1 TB WD1001FALS

    Read the article

  • Wireless Network suddenly cant connect after Windows update

    - by vinir
    UPDATE: As my patience started to end, the laptop started to display symptoms of other malfunctions, so I ended up returning it to Asus and actually had the price of the laptop back in store credit. I did not solve the problem per se, but as I don't have the notebook and the screen, the keyboard, the touchpad and other parts were malfunctioning, I can safely assume that it was put to rest. I don't know how to behave when my question isn't actually answered, but was "solved", so I placed this over here. Anyone that knows how to end this topic, I would appreciate the heads up. Thanks for everything, everyone, it's nice to see that this topic in the community was active even when all this time had passed. vinir So I bought an ASUS K43E notebook earlier this year and built a wireless conection to link it to. It worked great for the first weeks, but then I updated my Windows 7 Home Basic with the daily updates; After that my home network couldn't be reached no matter what I did. I have linux on dual boot on the same notebook and it can connect to my home wireless network flawlessly. I have a hunch that it's somehow related to the Network Profile settings. I have noticed my network was set as "Home network", but after the system updates I got changed to "Public". Now I can't connect to it to change the profile settings. My Atheros Network adapter is updated to the latest driver (march 2012), and I still can't connect. The funny thing is that the same thing happened to my mother's notebook, as it has the same Network Adapter, Atheros AR9285, as I recall it. I managed to fix it on my mother's computer by using an specific network LSP and profiling reset that was available through her notebook's antivirus program, avast! Internet Security. I can't get that to work on my notebook, but I suspect that some related tool might just make it work too. So the question is: how to modify a network's profile and settings that were stored in my notebook? I can't connect to the specific network on Windows, as stated before.

    Read the article

  • Can't recover hard drive

    - by BreezyChick89
    My drive got corrupt after a thunderstorm. It used to be 1 partition of 2.5tb but now it shows 2 partitions. It's weird because 300gig free space is about how much it had before corrupting, but it was part of the first partition. I tried $ sudo resize2fs -f /dev/sdb1 Resizing the filesystem on /dev/sdb1 to 536870911 (4k) blocks. resize2fs: Can't read an block bitmap while trying to resize /dev/sdb1 Please run 'e2fsck -fy /dev/sdb1' to fix the filesystem after the aborted resize operation. sudo e2fsck -f /dev/sdb1 e2fsck 1.42 (29-Nov-2011) The filesystem size (according to the superblock) is 610471680 blocks The physical size of the device is 536870911 blocks Either the superblock or the partition table is likely to be corrupt! Abort? n .... Error reading block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes Force rewrite<y>? yes Error writing block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes ... A lot of these. I can't use e2fsck -y because the first question aborts if I say "y". If I put a weight on the 'y' key it fails because none of the errors were really fixed. I asked this question before and tried using gparted but gparted fails because the first thing it does is: e2fsck -f -y -v /dev/sdb1 giving the same error. The disk status says healthy. There are no bad blocks. This is very frustrating because I can see the data in testdisk and it looks like it's all there. I already bought another 2.5tb drive and made a clone using dd. The next step if I can't fix this is to wipe that drive and just move the data with testdisk, but it seems certain folders will copy infinitely until the drive is full because of symlinks or errors so it's also a difficult option. sudo fdisk -l Disk /dev/sdb: 2500.5 GB, 2500495958016 bytes 255 heads, 63 sectors/track, 304001 cylinders, total 4883781168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005da5e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 4294969342 2147483647+ 83 Linux sudo badblocks -b 4096 -n -o badfile /dev/sdb 610471680 536870911 badfile is empty I also tried changing the superblock with "fsck -b" but all of them are the same.

    Read the article

  • SQL Express 2008 R2 on Amazon EC2 instance: tons of free memory, poor performance

    - by gravyface
    The old SQL Express 2005 was running on a low-end single Xeon CPU Dell server, RAID 5 7200 disks, 2 GB RAM (SBS 2003). I have not done any baseline measurements on the old physical server, but the Web app is used by half a dozen people (maybe 2 concurrently), so I figured "how bad can an Amazon EC2 instance be?". It's pretty horrible: a difference of 8 seconds of load time on one screen. First of all, I'm not a SQL guru, but here's what I've tried: Had a Small Instance, now running a c1.medium (High Cpu Medium) Windows 2008 32-bit R2 EBS-backed instance running IIS 7.5 and SQL Express 2008 R2. No noticeable improvement. Changed Page File from fixed 256 to Automatic. Setup a Striped Mirror from within Disk Management with two attached 1 GB EBS volumes. Moved database and transaction log, left everything else on the boot EBS volume. No noticeable change. Looked at memory, ~1000 MB of physical memory free (1.7 GB total). Changed SQL instance to use a minimum of 1024 RAM; restarted server, no change in memory usage. SQL still only using ~28MB of RAM(!). So I'm thinking: this database is tiny (28MB), why isn't the whole thing cached in RAM? Surely that would speed up performance. The transaction log is 241 MB. Seems kind of large in comparison -- has this not been committed? Is it a cause of performance degradation? I recall something about Recovery Models and log sizes somewhere in my travels, but not positive. Another thing: the old server was running SQL Express 2005. Not sure if that has any impact, but I tried changing the compatibility level from SQL 2000 to 2008, but that had no effect. Anyways, what else can I try here? Seems ridiculous to throw more virtual hardware at this thing. I know I/O is going to be rough on EBS volumes, but surely others are successfully running small .NET/SQL apps on reasonably priced instances?

    Read the article

  • TrueCrypt partition will no longer mount

    - by sparkyuiop
    I am hoping for some advice to help me out of my situation, with luck. I have a computer running Windows 7 Ultimate x64 with 3 hard disks installed. On my 2TB hard disk 2 (non-system disk) I have 4 partitions. One is for music, another for video, a downloads partition and a 500GB RAW Truecrypt encrypted partition / volume that I had setup to mount with 4 photographs used as keyfiles. The 4 photographs are located in my 'Documents' partition which is one of four partitions on my 1.5TB hard disk 1 (non-system disk) When I setup the disk encryption I did not (I'm 99% sure) create a password, I only used the 4 photograph keyfiles to mount the volume. Recently my 1TB hard disk 0 (system / boot) started to fail so I decided to replace it. I was going to clone the old disk to a new disk but decided that a fresh installation would be more beneficial. Once I had transferred all the required 'User Data' from my old hard disk 0 (C: disk) I discarded it. I reinstalled Truecrypt, pointed to the partition, selected my 4 keyfiles photographs and I mounted my encrypted volume with no issues. In fact I mounted it several times after re-installing Windows and after reboots. Now all of a sudden when I try and mount it I get the message "incorrect keyfile(s) and/or password or not a Truecrypt volume". Now I am not sure why this happened as I do not recall exactly what I did between last mounting the volume successfully and it not mounting. Here are some of the possible things I may have done to cause it to stop working but I am at a loss as to where to start to try and resolve the problem. 1. I had swapped the drive letters to a preferred order. 2. I possibly swapped the physical SATA connectors on the mainboard. 3. I enabled 'Hot Plugging' for the two non-system hard disk SATA ports and the DVD SATA port in the BIOS. I have tried changing the encrypted partition drive letter as suggested in another post but this does not help. On my old system the encrypted drive was drive "X". I have about tried it with all the other free drive letters but alas nothing changes. I do not recall what drive letter was allocated to the encrypted partition before I changed them all. I have not tried to change the letter back to what it possibly was to start with as I am happy with the current layout. I will try this is anyone thinks it would be worthwhile though. I do hope I have managed to convey my situation in an understandable manner and live in hope someone could help me recover years of personal files. Thank you very much for taking the time to read my post and for any suggestions you may offer. Regards Phillip Thorne (UK) Anyone???

    Read the article

  • is it a good idea to change a recovery partition from primary to logical? [HP laptop]

    - by DiegoDD
    I have a new HP laptop, model dv6-6c85la, with 1TB hard drive, and it has 4 primary partitions, like this: |<- system [199 MB] -|<- c: [899.8 GB] -|<- d:(recovery) [27.5 GB] -|<- e:(hp_tools) [4 GB] -| I wanted to make another partition, splitting "C" which is the main partition, into TWO partitions, and leave the rest as it is. but it doesn't let me because they are already 4 primary partitions (the ones in the diagram). I read somewhere, that i could in fact split C into 2 partitions, but only if the adjacent partition (in this case d:(recovery) is converted into a "logical" partition. That way, the new unallocated part taken from C, and the recovery partition, would each be logical, "inside" an extended partition (right???) As i understand, the resulting partitions would be: primary (system, no letter), primary (c:), extended [ logical (x:) | logical(d:recovery) ], primary (e: hp_tools) "x" being the new one. am i correct? My question is, if i do convert the recovery partition to logical (and thus, it is inside an extended partition adjacent to the new "x:" one), would i have any problems when in case of a disaster i would like to restore the system using the now logical instead of primary RECOVERY partition? Or it is completely safe to change it to logical? My main concern is because i think i may need to be primary so the recovery can proceed in boot time? Or i am completely wrong? how does the recovery process happens? I also understand that i can simply create recovery media, in DVDs, and then even i would be able to delete that recovery partition completely, but as of now, i don't want to do that. I may create the disks, but i don't want to delete the partition, simply because it would be a lot faster and easier to recover from a hard drive than disks. Wrapping up: if i change a recovery partition from primary to logical, will the system still be capable of using it to recover? or it NEEDS to be primary to work? The whole point is that i want to split C:, but as things are, i cant directly, i'd need to change the recovery partition to logical. Or is there another way? thanks.

    Read the article

  • How do I resolve "Unable to resolve attribute [organizationType.id] against path" exception?

    - by Dave
    I'm using Spring 3.1.1.RELEASE, Hibernate 4.1.0.Final, JUnit 4.8, and JPA 2.0 (hibernate-jpa-2.0-api). I'm trying to write a query and search based on fields of member fields. What I mean is I have this entity … @GenericGenerator(name = "uuid-strategy", strategy = "uuid.hex") @Entity @Table(name = "cb_organization", uniqueConstraints = {@UniqueConstraint(columnNames={"organization_id"})}) public class Organization implements Serializable { @Id @NotNull @GeneratedValue(generator = "uuid-strategy") @Column(name = "id") /* the database id of the Organization */ private String id; @ManyToOne @JoinColumn(name = "state_id", nullable = true, updatable = false) /* the State for the organization */ private State state; @ManyToOne @JoinColumn(name = "country_id", nullable = false, updatable = false) /* The country the Organization is in */ private Country country; @ManyToOne(optional = false) @JoinColumn(name = "organization_type_id", nullable = false, updatable = false) /* The type of the Organization */ private OrganizationType organizationType; Notice the members "organizationType," "state," and "country," which are all objects. I wish to build a query based on their id fields. This code @Override public List<Organization> findByOrgTypesCountryAndState(Set<String> organizationTypes, String countryId, String stateId) { CriteriaBuilder builder = entityManager.getCriteriaBuilder(); CriteriaQuery<Organization> criteria = builder.createQuery(Organization.class); Root<Organization> org = criteria.from(Organization.class); criteria.select(org).where(builder.and(org.get("organizationType.id").in(organizationTypes), builder.equal(org.get("state.id"), stateId), builder.equal(org.get("country.id"), countryId))); return entityManager.createQuery(criteria).getResultList(); } is throwing the exception below. How do I heal the pain? java.lang.IllegalArgumentException: Unable to resolve attribute [organizationType.id] against path at org.hibernate.ejb.criteria.path.AbstractPathImpl.unknownAttribute(AbstractPathImpl.java:116) at org.hibernate.ejb.criteria.path.AbstractPathImpl.locateAttribute(AbstractPathImpl.java:221) at org.hibernate.ejb.criteria.path.AbstractPathImpl.get(AbstractPathImpl.java:192) at org.mainco.subco.organization.repo.OrganizationDaoImpl.findByOrgTypesCountryAndState(OrganizationDaoImpl.java:248) at org.mainco.subco.organization.repo.OrganizationDaoTest.testFindByOrgTypesCountryAndState(OrganizationDaoTest.java:55) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.junit.runners.model.FrameworkMethod$1.runReflectiveCall(FrameworkMethod.java:44) at org.junit.internal.runners.model.ReflectiveCallable.run(ReflectiveCallable.java:15) at org.junit.runners.model.FrameworkMethod.invokeExplosively(FrameworkMethod.java:41) at org.junit.internal.runners.statements.InvokeMethod.evaluate(InvokeMethod.java:20) at org.springframework.test.context.junit4.statements.RunBeforeTestMethodCallbacks.evaluate(RunBeforeTestMethodCallbacks.java:74) at org.springframework.test.context.junit4.statements.RunAfterTestMethodCallbacks.evaluate(RunAfterTestMethodCallbacks.java:83) at org.springframework.test.context.junit4.statements.SpringRepeat.evaluate(SpringRepeat.java:72) at org.springframework.test.context.junit4.SpringJUnit4ClassRunner.runChild(SpringJUnit4ClassRunner.java:231) at org.junit.runners.BlockJUnit4ClassRunner.runChild(BlockJUnit4ClassRunner.java:49) at org.junit.runners.ParentRunner$3.run(ParentRunner.java:193) at org.junit.runners.ParentRunner$1.schedule(ParentRunner.java:52) at org.junit.runners.ParentRunner.runChildren(ParentRunner.java:191) at org.junit.runners.ParentRunner.access$000(ParentRunner.java:42) at org.junit.runners.ParentRunner$2.evaluate(ParentRunner.java:184) at org.springframework.test.context.junit4.statements.RunBeforeTestClassCallbacks.evaluate(RunBeforeTestClassCallbacks.java:61) at org.springframework.test.context.junit4.statements.RunAfterTestClassCallbacks.evaluate(RunAfterTestClassCallbacks.java:71) at org.junit.runners.ParentRunner.run(ParentRunner.java:236) at org.springframework.test.context.junit4.SpringJUnit4ClassRunner.run(SpringJUnit4ClassRunner.java:174) at org.eclipse.jdt.internal.junit4.runner.JUnit4TestReference.run(JUnit4TestReference.java:50) at org.eclipse.jdt.internal.junit.runner.TestExecution.run(TestExecution.java:38) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:467) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:683) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:390) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:197)

    Read the article

  • apache tomcat sermyadmin deployment error

    - by lepricon123
    I am getting the following errro when i try to start the application Mar 23, 2010 7:51:09 PM org.apache.catalina.core.ApplicationContext log INFO: Set web app root system property: 'sermyadmin-production-2.0.1' = [/usr/local/tomcat6/webapps/sermyadmin/] Mar 23, 2010 7:51:09 PM org.apache.catalina.core.ApplicationContext log INFO: Initializing log4j from [/usr/local/tomcat6/webapps/sermyadmin/WEB-INF/classes/log4j.properties] Mar 23, 2010 7:51:09 PM org.apache.catalina.core.ApplicationContext log INFO: Initializing Spring root WebApplicationContext Mar 23, 2010 7:51:23 PM org.apache.catalina.core.StandardContext listenerStart SEVERE: Exception sending context initialized event to listener instance of class org.codehaus.groovy.grails.web.context.GrailsContextLoaderListener org.springframework.beans.factory.access.BootstrapException: Error executing bootstraps; nested exception is org.codehaus.groovy.runtime.InvokerInvocationException: org.springframework.dao.InvalidDataAccessResourceUsageException: could not execute query; nested exception is org.hibernate.exception.SQLGrammarException: could not execute query at org.codehaus.groovy.grails.web.context.GrailsContextLoader.createWebApplicationContext(GrailsContextLoader.java:66) at org.springframework.web.context.ContextLoader.initWebApplicationContext(ContextLoader.java:199) at org.springframework.web.context.ContextLoaderListener.contextInitialized(ContextLoaderListener.java:45) at org.apache.catalina.core.StandardContext.listenerStart(StandardContext.java:3843) at org.apache.catalina.core.StandardContext.start(StandardContext.java:4350) at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:791) at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:771) at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:525) at org.apache.catalina.startup.HostConfig.deployWAR(HostConfig.java:829) at org.apache.catalina.startup.HostConfig.deployWARs(HostConfig.java:718) at org.apache.catalina.startup.HostConfig.deployApps(HostConfig.java:490) at org.apache.catalina.startup.HostConfig.start(HostConfig.java:1147) at org.apache.catalina.startup.HostConfig.lifecycleEvent(HostConfig.java:311) at org.apache.catalina.util.LifecycleSupport.fireLifecycleEvent(LifecycleSupport.java:117) at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1053) at org.apache.catalina.core.StandardHost.start(StandardHost.java:719) at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1045) at org.apache.catalina.core.StandardEngine.start(StandardEngine.java:443) at org.apache.catalina.core.StandardService.start(StandardService.java:516) at org.apache.catalina.core.StandardServer.start(StandardServer.java:710) at org.apache.catalina.startup.Catalina.start(Catalina.java:578) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:288) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413) Caused by: org.codehaus.groovy.runtime.InvokerInvocationException: org.springframework.dao.InvalidDataAccessResourceUsageException: could not execute query; nested exception is org.hibernate.exception.SQLGrammarException: could not execute query at org.apache.catalina.core.StandardContext.listenerStart(StandardContext.java:3843) at org.apache.catalina.core.StandardContext.start(StandardContext.java:4350) at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:791) at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:771) at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:525) at org.apache.catalina.startup.HostConfig.deployWAR(HostConfig.java:829) at org.apache.catalina.startup.HostConfig.deployWARs(HostConfig.java:718) at org.apache.catalina.startup.HostConfig.deployApps(HostConfig.java:490) at org.apache.catalina.startup.HostConfig.start(HostConfig.java:1147) at org.apache.catalina.startup.HostConfig.lifecycleEvent(HostConfig.java:311) at org.apache.catalina.util.LifecycleSupport.fireLifecycleEvent(LifecycleSupport.java:117) at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1053) at org.apache.catalina.core.StandardHost.start(StandardHost.java:719) at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1045) at org.apache.catalina.core.StandardEngine.start(StandardEngine.java:443) at org.apache.catalina.core.StandardService.start(StandardService.java:516) at org.apache.catalina.core.StandardServer.start(StandardServer.java:710) at org.apache.catalina.startup.Catalina.start(Catalina.java:578) ... 2 more Caused by: org.springframework.dao.InvalidDataAccessResourceUsageException: could not execute query; nested exception is org.hibernate.exception.SQLGrammarException: could not execute query at BootStrap$_closure1.doCall(BootStrap.groovy:7) ... 20 more Caused by: org.hibernate.exception.SQLGrammarException: could not execute query ... 21 more Caused by: com.mysql.jdbc.exceptions.jdbc4.MySQLSyntaxErrorException: Table 'opensips.jsec_role' doesn't exist at com.mysql.jdbc.Util.handleNewInstance(Util.java:406)

    Read the article

  • JPA thinks I'm deleting a detached object

    - by Steve
    So, I've got a DAO that I used to load and save my domain objects using JPA. I finally managed to get the transaction stuff working (with a bunch of help from the folks here...), now I've got another issue. In my test case, I call my DAO to load a domain object with a given id, check that it got loaded and then call the same DAO to delete the object I just loaded. When I do that I get the following: java.lang.IllegalArgumentException: Removing a detached instance mil.navy.ndms.conops.common.model.impl.jpa.Group#10 at org.hibernate.ejb.event.EJB3DeleteEventListener.performDetachedEntityDeletionCheck(EJB3DeleteEventListener.java:45) at org.hibernate.event.def.DefaultDeleteEventListener.onDelete(DefaultDeleteEventListener.java:108) at org.hibernate.event.def.DefaultDeleteEventListener.onDelete(DefaultDeleteEventListener.java:74) at org.hibernate.impl.SessionImpl.fireDelete(SessionImpl.java:794) at org.hibernate.impl.SessionImpl.delete(SessionImpl.java:772) at org.hibernate.ejb.AbstractEntityManagerImpl.remove(AbstractEntityManagerImpl.java:253) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:48) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:37) at java.lang.reflect.Method.invoke(Method.java:600) at org.springframework.orm.jpa.SharedEntityManagerCreator$SharedEntityManagerInvocationHandler.invoke(SharedEntityManagerCreator.java:180) at $Proxy27.remove(Unknown Source) at mil.navy.ndms.conops.common.dao.impl.jpa.GroupDao.delete(GroupDao.java:499) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:48) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:37) at java.lang.reflect.Method.invoke(Method.java:600) at org.springframework.aop.support.AopUtils.invokeJoinpointUsingReflection(AopUtils.java:304) at org.springframework.aop.framework.ReflectiveMethodInvocation.invokeJoinpoint(ReflectiveMethodInvocation.java:182) at org.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:149) at org.springframework.transaction.interceptor.TransactionInterceptor.invoke(TransactionInterceptor.java:106) at org.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:171) at org.springframework.aop.framework.JdkDynamicAopProxy.invoke(JdkDynamicAopProxy.java:204) at $Proxy28.delete(Unknown Source) at mil.navy.ndms.conops.common.dao.impl.jpa.GroupDaoTest.testGroupDaoSave(GroupDaoTest.java:89) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:48) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:37) at java.lang.reflect.Method.invoke(Method.java:600) at junit.framework.TestCase.runTest(TestCase.java:164) at junit.framework.TestCase.runBare(TestCase.java:130) at junit.framework.TestResult$1.protect(TestResult.java:106) at junit.framework.TestResult.runProtected(TestResult.java:124) at junit.framework.TestResult.run(TestResult.java:109) at junit.framework.TestCase.run(TestCase.java:120) at junit.framework.TestSuite.runTest(TestSuite.java:230) at junit.framework.TestSuite.run(TestSuite.java:225) at org.eclipse.jdt.internal.junit.runner.junit3.JUnit3TestReference.run(JUnit3TestReference.java:130) at org.eclipse.jdt.internal.junit.runner.TestExecution.run(TestExecution.java:38) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:460) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.runTests(RemoteTestRunner.java:673) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.run(RemoteTestRunner.java:386) at org.eclipse.jdt.internal.junit.runner.RemoteTestRunner.main(RemoteTestRunner.java:196) Now given that I'm using the same DAO instance, and I've not changed EntityManagers (unless Spring does so without letting me know), how can this be a detached object? My DAO code looks like this: public class GenericJPADao implements IWebDao, IDao, IDaoUtil { private static Logger logger = Logger.getLogger (GenericJPADao.class); protected Class voClass; @PersistenceContext(unitName = "CONOPS_PU") protected EntityManagerFactory emf; @PersistenceContext(unitName = "CONOPS_PU") protected EntityManager em; public GenericJPADao() { super ( ); ParameterizedType genericSuperclass = (ParameterizedType) getClass ( ).getGenericSuperclass ( ); this.voClass = (Class) genericSuperclass.getActualTypeArguments ( )[1]; } ... public void delete (INTFC modelObj, EntityManager em) { em.remove (modelObj); } @SuppressWarnings("unchecked") public INTFC findById (Long id) { return ((INTFC) em.find (voClass, id)); } } The test case code looks like: IGroup loadedGroup = dao.findById (group.getId ( )); assertNotNull (loadedGroup); assertEquals (group.getId ( ), loadedGroup.getId ( )); dao.delete (loadedGroup); // - This generates the above exception loadedGroup = dao.findById (group.getId ( )); assertNull(loadedGroup); Can anyone tell me what I'm doing wrong here? Thanks

    Read the article

  • Diagramming Software for a Developer/Designer

    - by Craig Walker
    For a long time I've been looking for a good diagramming/vector-based drawing program that meets my needs as a developer. I'd like to: Draw database diagrams Draw flow charts Draw object-modeling diagrams (UML being the standard) Draw other free-form diagrams (basically boxes & arrows with the occasional clipart) Draw mockups of user interfaces and web pages EDIT: I want good-looking electronic-format diagrams that I can show to 3rd parties, not just something for my own internal use. EDIT 2: I'm also looking for Windows software, although I'm toying with the idea of switching to Mac, so a really good Mac-only product might get me to switch. Basically I need a good vector graphic program (with decent grouping, connecting lines, and ideally auto-routing). I'd prefer a diagramming tool that can also be used for drawing (for the UI mockups) rather than a drawing tool that can also be used for diagrams. I've tried Visio on several occasions, and every time I've been disappointed. The interface always seems to get in my way at some point. It's pretty close to what I want, and the latest version (I got the trail from MS) seems to be better than previous ones in terms of usability, but I really don't want to plunk down that sort of cash for a mediocre product. I've tried Dia and Inkscape, and while initially promising and with the right price tag, I found both of them to be lacking in several ways (including some recurring bugs). I've toyed with getting Adobe Illustrator, but I've never used it before, and I have a feeling that it wouldn't handle the diagramming aspect very well, and I don't want to buy a copy just to find out it doesn't meet my needs. So far, the product that I've had the most success with is, sadly, OpenOffice Draw. It's free of course (which lowers my expectations and thus improves my view of it) and its usability is pretty good, but in the end I'd like something more suited to diagramming. I'm willing to spend real money (in the $500-$1K range) for a really good piece of software if it does everything I want it to. The front runner is of course Visio but I'm hoping for more. Does anybody have any recommendations? CONCLUSION: @dlamblin had the most informative post, but the part I gained the most from was his/her (and others) mention of OmniGraffle, not Gliffy. I gave Gliffy a try, and it seemed neet for occational use, but since it's a Flash app (note: not AJAX as dlamblin mentioned) it's still a bit of a pain to use (no keyboard shortcuts for copy/paste was pretty much a deal breaker for me). I also tried SmartDraw, but it had 3-strikes-you're-out against it: The trial period was only 7 days long. It used some nonstandard (and visually jarring) GUI widget toolkit for its UI. At the very least it makes me suspicious (how do I know it will actually work & support the standard Windows features?) It crashed on me early into my trial. OmniGraffle looks like exactly what I want... except that it's Mac-only (so I couldn't give it a try). However, it got good reviews from my Mac-owning coworker, and I hope to try it on a friend's Mac soon. If it's good enough then I might spring for a new MacBook.

    Read the article

  • TableView Cells Use Whole Screen Height

    - by Kyle
    I read through this tutorial Appcelerator: Using JSON to Build a Twitter Client and attempted to create my own simple application to interact with a Jetty server I setup running some Spring code. I basically call a get http request that gives me a bunch of contacts in JSON format. I then populate several rows with my JSON data and try to build a TableView. All of that works, however, my tableView rows take up the whole screen. Each row is one screen. I can scroll up and down and see all my data, but I'm trying to figure out what's wrong in my styling that's making the cells use the whole screen. My CSS is not great, so any help is appreciated. Thanks! Here's my js file that's loading the tableView: // create variable "win" to refer to current window var win = Titanium.UI.currentWindow; // Function loadContacts() function loadContacts() { // empty array "rowData" for table view cells var rowData = []; // create http client var loader = Titanium.Network.createHTTPClient(); // set http request method and url loader.setRequestHeader("Accept", "application/json"); loader.open("GET", "http://localhost:8080/contactsample/contacts"); // run the function when the data is ready for us to process loader.onload = function(){ Ti.API.debug("JSON Data: " + this.responseText); // evaluate json var contacts = JSON.parse(this.responseText); for(var i=0; i < contacts.length; i++) { var id = contacts[i].id; Ti.API.info("JSON Data, Row[" + i + "], ID: " + contacts[i].id); var name = contacts[i].name; Ti.API.info("JSON Data, Row[" + i + "], Name: " + contacts[i].name); var phone = contacts[i].phone; Ti.API.info("JSON Data, Row[" + i + "], Phone: " + contacts[i].phone); var address = contacts[i].address; Ti.API.info("JSON Data, Row[" + i + "], Address: " + contacts[i].address); // create row var row = Titanium.UI.createTableViewRow({ height:'auto' }); // create row's view var contactView = Titanium.UI.createView({ height:'auto', layout:'vertical', top:5, right:5, bottom:5, left:5 }); var nameLbl = Titanium.UI.createLabel({ text:name, left:5, height:24, width:236, textAlign:'left', color:'#444444', font:{ fontFamily:'Trebuchet MS', fontSize:16, fontWeight:'bold' } }); var phoneLbl = Titanium.UI.createLabel({ text: phone, top:0, bottom:2, height:'auto', width:236, textAlign:'right', font:{ fontSize:14} }); var addressLbl = Titanium.UI.createLabel({ text: address, top:0, bottom:2, height:'auto', width:236, textAlign:'right', font:{ fontSize:14} }); contactView.add(nameLbl); contactView.add(phoneLbl); contactView.add(addressLbl); row.add(contactView); row.className = "item" + i; rowData.push(row); } Ti.API.info("RowData: " + rowData); // create table view var tableView = Titanium.UI.createTableView( { data: rowData }); win.add(tableView); }; // send request loader.send(); } // get contacts loadContacts(); And here are some screens showing my problem. I tried playing with the top, bottom, right, left pixels a bit and didn't seem to be getting anywhere. All help is greatly appreciated. Thanks!

    Read the article

  • OSGI Declarative Services (DS): What is a good way of using service component instances

    - by Christoph
    I am just getting started with OSGI and Declarative Services (DS) using Equinox and Eclipse PDE. I have 2 Bundles, A and B. Bundle A exposes a component which is consumed by Bundle B. Both bundles also expose this service to the OSGI Service registry again. Everything works fine so far and Equinox is wireing the components together, which means the Bundle A and Bundle B are instanciated by Equinox (by calling the default constructor) and then the wireing happens using the bind / unbind methods. Now, as Equinox is creating the instances of those components / services I would like to know what is the best way of getting this instance? So assume there is third class class which is NOT instantiated by OSGI: Class WantsToUseComponentB{ public void doSomethingWithComponentB(){ // how do I get componentB??? Something like this maybe? ComponentB component = (ComponentB)someComponentRegistry.getComponent(ComponentB.class.getName()); } I see the following options right now: 1. Use a ServiceTracker in the Activator to get the Service of ComponentBundleA.class.getName() (I have tried that already and it works, but it seems to much overhead to me) and make it available via a static factory methods public class Activator{ private static ServiceTracker componentBServiceTracker; public void start(BundleContext context){ componentBServiceTracker = new ServiceTracker(context, ComponentB.class.getName(),null); } public static ComponentB getComponentB(){ return (ComponentB)componentBServiceTracker.getService(); }; } 2. Create some kind of Registry where each component registers as soon as the activate() method is called. public ComponentB{ public void bind(ComponentA componentA){ someRegistry.registerComponent(this); } or public ComponentB{ public void activate(ComponentContext context){ someRegistry.registerComponent(this); } } } 3. Use an existing registry inside osgi / equinox which has those instances? I mean OSGI is already creating instances and wires them together, so it has the objects already somewhere. But where? How can I get them? Conclusion Where does the class WantsToUseComponentB (which is NOT a Component and NOT instantiated by OSGI) get an instance of ComponentB from? Are there any patterns or best practises? As I said I managed to use a ServiceTracker in the Activator, but I thought that would be possible without it. What I am looking for is actually something like the BeanContainer of Springframework, where I can just say something like Container.getBean(ComponentA.BEAN_NAME). But I don't want to use Spring DS. I hope that was clear enough. Otherwise I can also post some source code to explain in more detail. Thanks Christoph UPDATED: Answer to Neil's comment: Thanks for clarifying this question against the original version, but I think you still need to state why the third class cannot be created via something like DS. Hmm don't know. Maybe there is a way but I would need to refactor my whole framework to be based on DS, so that there are no "new MyThirdClass(arg1, arg2)" statements anymore. Don't really know how to do that, but I read something about ComponentFactories in DS. So instead of doing a MyThirdClass object = new MyThirdClass(arg1, arg2); I might do a ComponentFactory myThirdClassFactory = myThirdClassServiceTracker.getService(); // returns a if (myThirdClassFactory != null){ MyThirdClass object = objectFactory.newInstance(); object.setArg1("arg1"); object.setArg2("arg2"); } else{ // here I can assume that some service of ComponentA or B went away so MyThirdClass Componenent cannot be created as there are missing dependencies? } At the time of writing I don't know exactly how to use the ComponentFactories but this is supposed to be some kind of pseudo code :) Thanks Christoph

    Read the article

< Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >