Search Results

Search found 10989 results on 440 pages for 'wpf commands'.

Page 421/440 | < Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >

• How broken is routing strategy that causes a martian packet (so far only) during tracepath?

  - by lkraav

  I believe I've achieved a table that routes packets from and to eth1/192.168.3.x through 192.168.3.1, and packets from and to eth0/192.168.1.x through 192.168.1.1 (helpful source). Question: when doing tracepath from 192.168.3.20 (from within vserver), I'm getting kernel: [318535.927489] martian source 192.168.3.20 from 212.47.223.33, on dev eth0 at or near the target IP, while intermediary hops go without (log below). I don't understand why this packet is arriving on eth0, instead of eth1, even after reading this: Note that you may see packets from non-routable IP addresses when running the traceroute or tracepath commands. While packets cannot be routed to these routers, packets sent between 2 routers only need to know the address of the next hop within the local networks, which could be a non-routable address. Can someone explain that paragraph in human language? Based on short initial trials so far, everything else seems to work without causing martians. Is this contained to the nature of tracepath operation or do I have some other bigger routing problem that will cause work traffic breakage? Side note: is it possible to inspect martian packet with tcpdump or wireshark or anything of the sort? I'm have not been able to get it to show up on my own. vserver-20 / # tracepath -n 212.47.223.33 1: 192.168.3.2 0.064ms pmtu 1500 1: 192.168.3.1 1.076ms 1: 192.168.3.1 1.259ms 2: 90.191.8.2 1.908ms 3: 90.190.134.194 2.595ms 4: 194.126.123.94 2.136ms asymm 5 5: 195.250.170.22 2.266ms asymm 6 6: 212.47.201.86 2.390ms asymm 7 7: no reply 8: no reply 9: no reply ^C Host routing: $ sudo ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:24:1d:de:b3:5d brd ff:ff:ff:ff:ff:ff inet 192.168.1.2/24 scope global eth0 4: eth1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:46:46:a3:6a brd ff:ff:ff:ff:ff:ff inet 192.168.3.2/27 scope global eth1 inet 192.168.3.20/27 brd 192.168.3.31 scope global secondary eth1 # linux-vserver instance $ sudo ip route default via 192.168.1.1 dev eth0 metric 3 unreachable 127.0.0.0/8 scope host 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.2 192.168.3.0/27 dev eth1 proto kernel scope link src 192.168.3.2 $ sudo ip rule 0: from all lookup local 32764: from all to 192.168.3.0/27 lookup dmz 32765: from 192.168.3.0/27 lookup dmz 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table dmz default via 192.168.3.1 dev eth1 metric 4 192.168.3.0/27 dev eth1 scope link metric 4 Gateway routing # ip route 10.24.0.2 dev tun0 proto kernel scope link src 10.24.0.1 10.24.0.0/24 via 10.24.0.2 dev tun0 192.168.3.0/24 dev br-dmz proto kernel scope link src 192.168.3.1 192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1 $ISP_NET/23 dev eth0.1 proto kernel scope link src $WAN_IP default via $ISP_GW dev eth0.1 Additional background Options for non-virtualized network interface isolation?

  Read the article

• Blocking access to websites with objective-C / root privileges in objective-C

  - by kvaruni

  I am writing a program in Objective-C (XCode 3.2, on Snow Leopard) that is capable of either selectively blocking certain sites for a duration or only allow certain sites (and thus block all others) for a duration. The reasoning behind this program is rather simple. I tend to get distracted when I have full internet access, but I do need internet access during my working hours to get to a number of work-related websites. Clearly, this is not a permanent block, but only helps me to focus whenever I find myself wandering a bit too much. At the moment, I am using a Unix script that is called via AppleScript to obtain Administrator permissions. It then activates a number of ipfw rules and clears those after a specific duration to restore full internet access. Simple and effective, but since I am running as a standard user, it gets cumbersome to enter my administrator password each and every time I want to go "offline". Furthermore, this is a great opportunity to learn to work with XCode and Objective-C. At the moment, everything works as expected, minus the actual blocking. I can add a number of sites in a list, specify whether or not I want to block or allow these websites and I can "start" the blocking by specifying a time until which I want to stay "offline". However, I find it hard to obtain clear information on how I can run a privileged Unix command from Objective-C. Ideally, I would like to be able to store information with respect to the Administrator account into the Keychain to use these later on, so that I can simply move into "offline" mode with the convenience of clicking a button. Even more ideally, there might be some class in Objective-C with which I can block access to some/all websites for this particular user without needing to rely on privileged Unix commands. A third possibility is in starting this program with root permissions and the reducing the permissions until I need them, but since this is a GUI application that is nested in the menu bar of OS X, the results are rather awkward and getting it to run each and every time with root permission is no easy task. Anyone who can offer me some pointers or advice? Please, no security-warnings, I am fully aware that what I want to do is a potential security threat.

  Read the article

• Error while starting Rails server

  - by Girish Anand

  Hello i am new to ruby and rails ... but when i am starting the rail server i am getting this error This is the error i am getting D:\mynewapp>ruby script/server = Booting WEBrick = Rails 2.3.5 application starting on http://0.0.0.0:3000 D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require': n such file to load -- rush (MissingSourceFile) from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:156:inblock in require' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:521:in new_constants_in' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:156:inrequire' from D:/mynewapp/vendor/gems/delayed_job-1.7.0/lib/delayed/worker.r 1:in <top (required)>' from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:156:inblock in require' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:521:in new_constants_in' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:156:inrequire' from D:/mynewapp/vendor/gems/delayed_job-1.7.0/lib/delayed_job.rb:6 n <top (required)>' from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:156:inblock in require' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:521:in new_constants_in' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:156:inrequire' from D:/mynewapp/config/environment.rb:39:in block in <top (requir )>' from D:/ruby/lib/ruby/gems/1.9.1/gems/rails-2.3.5/lib/initializer.rb:1 :inrun' from D:/mynewapp/config/environment.rb:9:in <top (required)>' from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:156:inblock in require' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:521:in new_constants_in' from D:/ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.5/lib/active_s port/dependencies.rb:156:inrequire' from D:/ruby/lib/ruby/gems/1.9.1/gems/rails-2.3.5/lib/commands/server. :84:in <top (required)>' from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from D:/ruby/lib/ruby/site_ruby/1.9.1/rubygems/custom_require.rb:36:in require' from script/server:3:in' Any help will be appreciated Thanks in Advance

  Read the article

• WiX unresolved reference error

  - by David

  I'm using Wix version 3.0.5419.0. I have two .wxs files, one which is a fragment, and another which uses the fragment to create the .msi file. Here is the file which uses the fragment (DaisyFarmer.wxs): <?xml version='1.0' encoding='windows-1252'?> <Wix xmlns='http://schemas.microsoft.com/wix/2006/wi' xmlns:iis='http://schemas.microsoft.com/wix/IIsExtension'> <Product Name='Daisy Web Site 1.0' Id='BB7FBBE4-0A25-4cc7-A39C-AC916B665220' UpgradeCode='8A5311DE-A125-418f-B0E1-5A30B9C667BD' Language='1033' Codepage='1252' Version='1.0.0' Manufacturer='the man'> <Package Id='5F341544-4F95-4e01-A2F8-EF74448C0D6D' Keywords='Installer' Description="desc" Manufacturer='the man' InstallerVersion='100' Languages='1033' Compressed='yes' SummaryCodepage='1252' /> <Media Id='1' Cabinet='Sample.cab' EmbedCab='yes' DiskPrompt="CD-ROM #1" /> <Property Id='DiskPrompt' Value="the man" /> <PropertyRef Id="NETFRAMEWORK35"/> <Condition Message='This setup requires the .NET Framework 3.5.'> <![CDATA[Installed OR (NETFRAMEWORK35)]]> </Condition> <Feature Id='DaisyFarmer' Title='DaisyFarmer' Level='1'> <ComponentRef Id='SchedulerComponent' /> </Feature> </Product> </Wix> The fragment I'm referencing is (Scheduler.wxs): <?xml version="1.0" encoding="utf-8"?> <Wix xmlns="http://schemas.microsoft.com/wix/2006/wi"> <Fragment> <DirectoryRef Id="TARGETDIR"> <Directory Id="dir2787390E4B7313EB8005DE08108EFEA4" Name="scheduler"> <Component Id="SchedulerComponent" Guid="{9254F7E1-DE41-4EE5-BC0F-BA668AF051CB}"> <File Id="fil9A013D0BFB837BAC71FED09C59C5501B" KeyPath="yes" Source="SourceDir\DTBookMonitor.exe" /> <File Id="fil4F0D8D05F53E6AFBDB498E7C75C2D98F" KeyPath="no" Source="SourceDir\DTBookMonitor.exe.config" /> <File Id="filF02F4686267D027CB416E044E8C8C2FA" KeyPath="no" Source="SourceDir\monitor.bat" /> <File Id="fil05B8FF38A3C85FE6C4A58CD6FDFCD2FB" KeyPath="no" Source="SourceDir\output.txt" /> <File Id="fil397F04E2527DCFDF7E8AC1DD92E48264" KeyPath="no" Source="SourceDir\pipelineOutput.txt" /> <File Id="fil83DFACFE7F661A9FF89AA17428474929" KeyPath="no" Source="SourceDir\process.bat" /> <File Id="fil2809039236E0072642C52C6A52AD6F2F" KeyPath="no" Source="SourceDir\README.txt" /> </Component> </Directory> </DirectoryRef> </Fragment> </Wix> I then run the following commands: candle -ext WixUtilExtension -ext WiXNetFxExtension DaisyFarmer.wxs Scheduler.wxs light -sice:ICE20 -ext WixUtilExtension -ext WiXNetFxExtension Scheduler.wixobj DaisyFarmer.wixobj -out DaisyFarmer.msi I'm getting an error when I run light.exe which says "DaisyFarmer.wxs(20) : error LGHT0094 : Unresolved reference to symbol 'Component:SchedulerComponent' in section 'Product:{BB7FBBE4-0A25-4CC7-A39C-AC916B665220}'." What am I missing?

  Read the article

• Can't get gitosis and ssh to play nice on cygwin

  - by Noel Kennedy

  I have followed this guide to setting up gitosis on a windows 2003 server via cygwin. I have now got to a point where it largely works. I can clone, pull and push. The problem I am having is that I think I have not got the ssh bit right at all. When I connect via msysgit from machines and accounts where I have not created or uploaded ssh keys it works. Every time I clone, pull or push I get a password challenge for the 'git' user running on the server but basically I can execute git commands. When I connect with users with an ssh key in the ~/.ssh folder, I don't get the password challange and instead I get a permissions failure: DEBUG:gitosis.serve.main:Got command "git-upload-pack '/cris.git'" DEBUG:gitosis.access.haveAccess:Access check for 'teamcity@hhit24808' as 'writable' on 'cris.git'... DEBUG:gitosis.access.haveAccess:Stripping .git suffix from 'cris.git', new value 'cris' DEBUG:gitosis.access.haveAccess:Access check for 'teamcity@hhit24808' as 'writeable' on 'cris.git'... DEBUG:gitosis.access.haveAccess:Stripping .git suffix from 'cris.git', new value 'cris' DEBUG:gitosis.access.haveAccess:Access check for 'teamcity@hhit24808' as 'readonly' on 'cris.git'... DEBUG:gitosis.access.haveAccess:Stripping .git suffix from 'cris.git', new value 'cris' ERROR:gitosis.serve.main:Repository read access denied fatal: The remote end hung up unexpectedly I have uploaded the public rsa key into the key_dir folder. Here is my conf file: [gitosis] loglevel = DEBUG [group gitosis-admin] writable = gitosis-admin members = myemail@mydomain [group cris-developers] members = myemail@mydomain TeamCity@HHIT24808 writable = cris If it matters, I have generated a key without a passphrase as I believe this is necessary to enable ssh for automated scripts. When I use keys with a passphrase, I get challanged for the phrase but then get the same permissions problem. I have tried 'writable' and 'writeable' for permissions. Help!! Update 1: When I try to clone a non-existant repo, I get the same error message, co-incidence? Update 2: Wierd, I've got one machine and one login working. It seems to be something to do with the syntax for addressing git over ssh. This now works on one machine for one login: git clone git@servername:cris.git The same command fails for a user on another machine without an uploaded ssh key. But this command works (after being challanged for git@servername's password) git clone git@servername:/home/git/repositories/cris.git neither command works on a 2nd login whose ssh key has been uploaded

  Read the article

• Integrating POP3 client functionality into a C# application?

  - by flesh

  I have a web application that requires a server based component to periodically access POP3 email boxes and retrieve emails. The service then needs to process the emails which will involve: Validating the email against some business rules (does it contain a valid reference in the subject line, which user sent the mail, etc.) Analysing and saving any attachments to disk Take the email body and attachment details and create a new item in the database Or update an existing item where the reference matches the incoming email subject line What is the best way to approach this? I really don't want to have to write a POP3 client from scratch, but I need to be able to customize the processing of emails. Ideally I would be able to plug in some component that does the access and retrieval for me, returning arrays of attachments, body text, subject line, etc. ready for my processing... [ UPDATE: Reviews ] OK, so I have spent a fair amount of time looking into (mainly free) .NET POP3 libraries so I thought I'd provide a short review of some of those mentioned below and a few others: Pop3.net - free - works OK, very basic in terms of functionality provided. This is pretty much just the POP3 commands and some base64 encoding, but it's very straight forward - probably a good introduction Pop3 Wizard - commercial / some open source code - couldn't get this to build, missing DLLs, I wouldn't bother with this C#Mail - free - works well, comes with Mime parser and SMTP client, however the comments are in Japanese (not a big deal) and it didn't work with SSL 'out of the box' - I had to change the SslStream constructor after which it worked no problem OpenPOP - free - hasn't been updated for about 5 years so it's current state is .NET 1.0, doesn't support SSL but that was no problem to resolve - I just replaced the existing stream with an SslStream and it worked. Comes with Mime parser. Of the free libraries, I'd go for C#Mail or OpenPOP. I looked at a few commercial libraries: Chillkat, Rebex, RemObjects, JMail.net. Based on features, price and impression of the company I would probably go for Rebex and may in the future if my requirements change or I run into production issues with either of C#Mail or OpenPOP. In case anyone's needs it, this is the replacement SslStream constructor that I used to enable SSL with C#Mail and OpenPOP: SslStream stream = new SslStream(clientSocket.GetStream(), false, delegate(object sender, X509Certificate cert, X509Chain chain, SslPolicyErrors errors) { return true; });

  Read the article

• C# - Alternative to System.Timers.Timer, to call a function at a specific time.

  - by Fábio Antunes

  Hello everybody. I want to call a specific function on my C# application at a specific time. At first i thought about using a Timer (System.Time.Timer), but that soon became impossible to use. Why? Simple. The Timer Class requires a Interval in milliseconds, but considering that i might want the function to be executed, lets says in a week that would mean: 7 Days = 168 hours; 168 Hours = 10,080 minutes; 10,080 Minutes = 6,048,000 seconds; 6,048,000 Seconds = 6,048,000,000 milliseconds; So the Interval would be 6,048,000,000; Now lets remember that the Interval accepted data type is int, and as we know int range goes from -2,147,483,648 to 2,147,483,647. That makes Timer useless in this case once we cannot set a Interval bigger that 2,147,483,647 milliseconds. So i need a solution where i could specify when the function should be called. Something like this: solution.ExecuteAt = "30-04-2010 15:10:00"; solution.Function = "functionName"; solution.Start(); So when the System Time would reach "30-04-2010 15:10:00" the function would be executed in the application. How can this problem be solved? Thanks just by taking the time to read my question. But if you could provide me with some help i would be most grateful. Additional Info: What these functions will do? Getting climate information and based on that info: Starting / Shutting down other Applications (most of them Console Based); Sending custom Commands to those Console Applications; Power down, Rebooting, Sleep, Hibernate the computer; And if possible schedule the BIOS to Power Up the Computer; EDIT: It would seem that the Interval accepted data type is double, however if you set a value bigger that an int to the Interval, and call Start() it throws a exception [0, Int32.MaxValue]. EDIT 2: Jørn Schou-Rode suggested using Ncron to handle the scheduling tasks, and at first look this seems a good solution, but i would like to hear about some who as worked with it.

  Read the article

• Progress gauge in status bar, using Cody Precord's ProgressStatusBar

  - by MCXXIII

  Hi. I am attempting to create a progress gauge in the status bar for my application, and I'm using the example in Cody Precord's wxPython 2.8 Application Development Cookbook. I've reproduced it below. For now I simply wish to show the gauge and have it pulse when the application is busy, so I assume I need to use the Start/StopBusy() methods. Problem is, none of it seems to work, and the book doesn't provide an example of how to use the class. In the __init__ of my frame I create my status bar like so: self.statbar = status.ProgressStatusBar( self ) self.SetStatusBar( self.statbar ) Then, in the function which does all the work, I have tried things like: self.GetStatusBar().SetRange( 100 ) self.GetStatusBar().SetProgress( 0 ) self.GetStatusBar().StartBusy() self.GetStatusBar().Run() # work done here self.GetStatusBar().StopBusy() And several combinations and permutations of those commands, but nothing happens, no gauge is ever shown. The work takes several seconds, so it's not because the gauge simply disappears again too quickly for me to notice. I can get the gauge to show up by removing the self.prog.Hide() line from Precord's __init__ but it still doesn't pulse and simply disappears never to return once work has finished the first time. Here's Precord's class: class ProgressStatusBar( wx.StatusBar ): '''Custom StatusBar with a built-in progress bar''' def __init__( self, parent, id_=wx.ID_ANY, style=wx.SB_FLAT, name='ProgressStatusBar' ): super( ProgressStatusBar, self ).__init__( parent, id_, style, name ) self._changed = False self.busy = False self.timer = wx.Timer( self ) self.prog = wx.Gauge( self, style=wx.GA_HORIZONTAL ) self.prog.Hide() self.SetFieldsCount( 2 ) self.SetStatusWidths( [-1, 155] ) self.Bind( wx.EVT_IDLE, lambda evt: self.__Reposition() ) self.Bind( wx.EVT_TIMER, self.OnTimer ) self.Bind( wx.EVT_SIZE, self.OnSize ) def __del__( self ): if self.timer.IsRunning(): self.timer.Stop() def __Reposition( self ): '''Repositions the gauge as necessary''' if self._changed: lfield = self.GetFieldsCount() - 1 rect = self.GetFieldRect( lfield ) prog_pos = (rect.x + 2, rect.y + 2) self.prog.SetPosition( prog_pos ) prog_size = (rect.width - 8, rect.height - 4) self.prog.SetSize( prog_size ) self._changed = False def OnSize( self, evt ): self._changed = True self.__Reposition() evt.Skip() def OnTimer( self, evt ): if not self.prog.IsShown(): self.timer.Stop() if self.busy: self.prog.Pulse() def Run( self, rate=100 ): if not self.timer.IsRunning(): self.timer.Start( rate ) def GetProgress( self ): return self.prog.GetValue() def SetProgress( self, val ): if not self.prog.IsShown(): self.ShowProgress( True ) if val == self.prog.GetRange(): self.prog.SetValue( 0 ) self.ShowProgress( False ) else: self.prog.SetValue( val ) def SetRange( self, val ): if val != self.prog.GetRange(): self.prog.SetRange( val ) def ShowProgress( self, show=True ): self.__Reposition() self.prog.Show( show ) def StartBusy( self, rate=100 ): self.busy = True self.__Reposition() self.ShowProgress( True ) if not self.timer.IsRunning(): self.timer.Start( rate ) def StopBusy( self ): self.timer.Stop() self.ShowProgress( False ) self.prog.SetValue( 0 ) self.busy = False def IsBusy( self ): return self.busy

  Read the article

• How to create StackedBarSeries with custom tooltip without losing standard colors

  - by Simon_Weaver

  I have a StackedBarSeries in Silverlight 4 charting (latest release). I have created a DataPointStyle called MyDataPointStyle for a custom tooltip. By itself this breaks the standard palette used for the different bars. I've applied a custom palette - as described in David Anson's blog to the chart. However when I have the DataPointStyle set for my SeriesDefinition objects it does not use this palette. I'm not sure what I'm missing - but David specifically says : ... it enables the use of DynamicResource (currently only supported by the WPF platform) to let users customize their DataPointStyle without inadvertently losing the default/custom Palette colors. (Note: A very popular request!) Unfortunately I'm inadvertently losing these colors - and I can't see why? <chartingToolkit:Chart.Palette> <dataviz:ResourceDictionaryCollection> <ResourceDictionary> <Style x:Key="DataPointStyle" TargetType="Control"> <Setter Property="Background" Value="Blue"/> </Style> </ResourceDictionary> <ResourceDictionary> <Style x:Key="DataPointStyle" TargetType="Control"> <Setter Property="Background" Value="Green"/> </Style> </ResourceDictionary> <ResourceDictionary> <Style x:Key="DataPointStyle" TargetType="Control"> <Setter Property="Background" Value="Red"/> </Style> </ResourceDictionary> </dataviz:ResourceDictionaryCollection> </chartingToolkit:Chart.Palette> <chartingToolkit:Chart.Series> <chartingToolkit:StackedBarSeries> <chartingToolkit:SeriesDefinition IndependentValueBinding="{Binding SKU}" DependentValueBinding="{Binding Qty}" DataPointStyle="{StaticResource MyDataPointStyle}" Title="Regular"/> <chartingToolkit:SeriesDefinition IndependentValueBinding="{Binding SKU}" DependentValueBinding="{Binding Qty}" DataPointStyle="{StaticResource MyDataPointStyle}" Title="FSP Orders"/> <chartingToolkit:StackedBarSeries.IndependentAxis> <chartingToolkit:CategoryAxis Title="SKU" Orientation="Y" FontStyle="Italic" AxisLabelStyle="{StaticResource LeftAxisStyle}"/> </chartingToolkit:StackedBarSeries.IndependentAxis> <chartingToolkit:StackedBarSeries.DependentAxis> <chartingToolkit:LinearAxis Orientation="X" ExtendRangeToOrigin="True" Minimum="0" ShowGridLines="True" /> </chartingToolkit:StackedBarSeries.DependentAxis> </chartingToolkit:StackedBarSeries > </chartingToolkit:Chart.Series> </chartingToolkit:Chart>

  Read the article

• Problem using ‘useLegacyV2RuntimeActivationPolicy’ & supportedRuntime in an application

  - by Notre

  Hello, I've modified a couple of different applications' .config file like this: <startup useLegacyV2RuntimeActivationPolicy="true"> <supportedRuntime version="v4.0"/> </startup> When I did this for devenv.exe.config (VS 2005 - don't ask :) ), things work great - most of the Visual Studio used .NET 2.0 but I was able to make use of an assembly targeting .NET 4.0 framework. I tried to do the same thing for a custom .exe, which happens to be based on MS CAB (slightly modified) and has a hybrid mix of WPF and WinForms content. As soon as I modified this application's app config file, I started getting this exception, sometime during application startup: The Undo operation encountered a context that is different from what was applied in the corresponding Set operation. The possible cause is that a context was Set on the thread and not reverted(undone). System.InvalidOperationException: The Undo operation encountered a context that is different from what was applied in the corresponding Set operation. The possible cause is that a context was Set on the thread and not reverted(undone). There's a big long stack trace that doesn't show anything in my application code directly (just a bunch of MS assemblies). If I modify the application's .config file to this: <startup useLegacyV2RuntimeActivationPolicy="true"> </startup> i.e.I remove the supportedRuntime element, then the application doesn't throw this exception. But when I go to the point in my code where I try to load my .NET 4 assembly, if fails with this: System.BadImageFormatException: Could not load file or assembly '' or one of its dependencies. This assembly is built by a runtime newer than the currently loaded runtime and cannot be loaded. I guess this is expected. I have two questions: 1) Any idea why I'm getting the System.InvalidOperationException exception when I modify this application's configuration file to include the supportedRuntime element, adding .NET 4 support and any suggestions on what I can do about it? 2) If the answer is "no idea why/don't know what you can do about it", then is possible for my .NET 3.5 SP1 code (C#) to provide more fine grain support for conditionally adding .NET 4 runtime support for a certain assembly(ies) without converting my entire application to target .NET 4, or without using the declarative config file approach? At some point I would convert the entire application to target .NET 4, but for the short term this is daunting task and I'm hope for some short term solution/hack. Thank you very much for any advice you can give!

  Read the article

• Eclipse Galileo won't start after OS X update to 10.6.3

  - by GC

  Hi All, I have just updated os x to 10.6.3 and no Eclipse won't start the logs show the following error, but I can't figure it out. Can anyone shed any light? !SESSION 2010-03-30 10:06:38.244 ----------------------------------------------- eclipse.buildId=M20090917-0800 java.version=1.6.0_17 java.vendor=Apple Inc. BootLoader constants: OS=macosx, ARCH=x86, WS=cocoa, NL=en_US Framework arguments: -product org.eclipse.epp.package.php.product -keyring /Users/gav/.eclipse_keyring -showlocation Command-line arguments: -os macosx -ws cocoa -arch x86 -product org.eclipse.epp.package.php.product -keyring /Users/gav/.eclipse_keyring -showlocation !ENTRY org.eclipse.ui.workbench 2 0 2010-03-30 10:06:40.139 !MESSAGE A handler conflict occurred. This may disable some commands. !SUBENTRY 1 org.eclipse.ui.workbench 2 0 2010-03-30 10:06:40.139 !MESSAGE Conflict for 'com.aptana.ide.editors.views.actions.actionKeyCommand': HandlerActivation(commandId=com.aptana.ide.editors.views.actions.actionKeyCommand, handler=com.aptana.ide.editors.views.actions.ActionKeyCommandHandler, expression=,sourcePriority=0) HandlerActivation(commandId=com.aptana.ide.editors.views.actions.actionKeyCommand, handler=com.aptana.ide.editors.views.actions.ActionKeyCommandHandler, expression=,sourcePriority=0) !ENTRY org.eclipse.ui 4 0 2010-03-30 10:06:40.964 !MESSAGE Unhandled event loop exception !STACK 0 java.lang.NullPointerException at org.eclipse.swt.graphics.Device.getFontList(Device.java:369) at org.eclipse.jface.resource.FontRegistry.filterData(FontRegistry.java:465) at org.eclipse.jface.resource.FontRegistry.createFont(FontRegistry.java:499) at org.eclipse.jface.resource.FontRegistry.defaultFontRecord(FontRegistry.java:563) at org.eclipse.jface.resource.FontRegistry.defaultFontData(FontRegistry.java:575) at org.eclipse.jface.resource.FontRegistry.getFontData(FontRegistry.java:591) at org.eclipse.ui.internal.themes.ThemeElementHelper.installFont(ThemeElementHelper.java:116) at org.eclipse.ui.internal.themes.ThemeElementHelper.populateRegistry(ThemeElementHelper.java:59) at org.eclipse.ui.internal.Workbench$33.runWithException(Workbench.java:1482) at org.eclipse.ui.internal.StartupThreading$StartupRunnable.run(StartupThreading.java:31) at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35) at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:134) at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3405) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3102) at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2316) at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2221) at org.eclipse.ui.internal.Workbench$5.run(Workbench.java:500) at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332) at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:493) at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149) at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEApplication.java:113) at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:194) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLauncher.java:110) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.java:79) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:368) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:559) at org.eclipse.equinox.launcher.Main.basicRun(Main.java:514) at org.eclipse.equinox.launcher.Main.run(Main.java:1311) It looks like the update may have upgraded the Java version, possibly :S but I don't know if this can be rolled back even if it did update it. java version "1.6.0_17" Java(TM) SE Runtime Environment (build 1.6.0_17-b04-248-10M3025) Java HotSpot(TM) 64-Bit Server VM (build 14.3-b01-101, mixed mode) Thanks in advance!

  Read the article

• Application Architecture using WCF and System.AddIn

  - by Silverhalide

  A little background -- we're designing an application that uses a client/server architecture consisting of: A server which loads server-side modules, potentially developed by other teams. A client which loads corresponding client-side modules (also potentially developed by those other teams; each client module corresponds with a server module). The client side communicates with the server side for general coordination, and as well as module specific tasks. (At this point, I think that means client talks to server, client modules talk to server modules.) Environment is .NET 3.5, and client side is WPF. The deployment scenario introduces the potential to upgrade the server, any server-side module, the client, and any client-side module independently. However, being able to "work" using mismatched versions is required. I'm therefore concerned about versioning issues. My thinking so far: A Windows Service for the server. Using System.AddIn for the server to load and communicate with the server modules will give us the greatest flexibility in terms of version compatability between server and server modules. The server and each server module vend WCF services for communication to the client side; communication between the server and a server module, or between two server modules use the AddIn contracts. (One advantage of this is that a module can expose a different interface within the server and outside it.) Similarly, the client uses System.AddIn to find, load, and communicate with the client modules. Client communications with client modules is via the AddIn interface; communications from the client and from client modules to the server side are via WCF. For maximum resilience, each module will run in a separate app-domain. In general, the system has modest performance requirements, so marshalling and crossing process boundaries is not expected to be a performance concern. (Performance requirement is basically summed up by: don't get in the way of the other parts of the system not described here.) My questions are around the idea of having two different communication and versioning models to work with which will be an added burden on our developers. System.AddIn seems quite powerful, but also a little unwieldly. (I'm also unsure of Microsoft's commitment to it in the future.) On the other hand, I'm not thrilled with WCF's versioning capabilities. I have a feeling that it would be possible to implement the System.AddIn view/adapter/contract system within WCF, but being fairly new to both technologies, I would have no idea of where to start. So... Am I on the right track here? Am I doing this the hard way? Are there gotchas I need to be aware of on this road? Thanks.

  Read the article

• Best programming aids for a quadriplegic programmer

  - by Peter Rowell

  Before you jump to conclusions, yes, this is programming related. It covers a situation that comes under the heading of, "There, but for the grace of God, go you or I." This is brand new territory for me so I'm asking for some serious help here. A young man, Honza Ripa, in a nearby town did the classic Dumb Thing two weeks after graduating from High School -- he dove into shallow water in the Russian River and had a C-4/C-5 break, sometimes called a Swimming Pool break. In a matter of seconds he went from an exceptional golfer and wrestler to a quadriplegic. (Read the story ... all of us should have been so lucky as to have a girlfriend like Brianna.) That was 10 months ago and he has regained only tiny amounts of control of his right index finger and a couple of other hand/foot motions, none of them fine-grained. His total control of his computer (currently running Win7, but we can change that as needed) is via voice command. Honza's not dumb. He had a 3.7 GPA with AP math and physics. The Problems: Since all of his input is via voice command, he is concerned that the predominance of special characters in programming will require vast amount of verbose commands. Does anyone know of any well done voice input system specifically designed for programmers? I'm thinking about something that might be modal--e.g. you say "Python input" and it goes into a macro mode for doing class definitions, etc. Given all of the RSI in programmer-land there's got to be something out there. What OS(es) does it run on? I am planning on teaching him Python, which is my preferred language for programming and teaching. Are there any applications / whatevers that are written in Python and would be a particularly good match for engaging him mentally while supporting his disability? One of his expressed interests is in stock investing, but that not might be a good starting point for a brand-new programmer. There are a lot of environments (Flash, JavaScript, etc) that are not particularly friendly to people with accessibility challenges. I vaguely remember (but cannot find) a research project that basically created an overlay system on top of a screen environment and then allowed macro command construction on top of the screen image. If we can get/train this system, we may be able to remove many hurdles to using the net. I am particularly interested in finding open source Python-based robotics and robotic prostheses projects so that he can simultaneously learn advanced programming concepts while learning to solve some of his own immediate problems. I've done a ton of googling on this, but I know there things I'm missing. I'm asking the SO community to step up to the plate here. I know this group has the answers, so let me hear them! Overwhelm me with the opportunities that any of us might have/need to still program after such a life-changing event.

  Read the article

• Injecting jms resource in servlet & best practice for MDB

  - by kislo_metal

  using ejb 3.1, servlet 3.0 (glassfish server v3) Scenario: I have MDB that listen to jms messages and give processing to some other session bean (Stateless). Servelet injecting jms resource. Question 1: Why servlet can`t inject jms resources when they use static declaration ? @Resource(mappedName = "jms/Tarturus") private static ConnectionFactory connectionFactory; @Resource(mappedName = "jms/StyxMDB") private static Queue queue; private Connection connection; and @PostConstruct public void postConstruct() { try { connection = connectionFactory.createConnection(); } catch (JMSException e) { e.printStackTrace(); } } @PreDestroy public void preDestroy() { try { connection.close(); } catch (JMSException e) { e.printStackTrace(); } } The error that I get is : [#|2010-05-03T15:18:17.118+0300|WARNING|glassfish3.0|javax.enterprise.system.container.web.com.sun.enterprise.web|_ThreadID=35;_ThreadName=Thread-1;|StandardWrapperValve[WorkerServlet]: PWC1382: Allocate exception for servlet WorkerServlet com.sun.enterprise.container.common.spi.util.InjectionException: Error creating managed object for class ua.co.rufous.server.services.WorkerServiceImpl at com.sun.enterprise.container.common.impl.util.InjectionManagerImpl.createManagedObject(InjectionManagerImpl.java:312) at com.sun.enterprise.web.WebContainer.createServletInstance(WebContainer.java:709) at com.sun.enterprise.web.WebModule.createServletInstance(WebModule.java:1937) at org.apache.catalina.core.StandardWrapper.loadServlet(StandardWrapper.java:1252) Caused by: com.sun.enterprise.container.common.spi.util.InjectionException: Exception attempting to inject Unresolved Message-Destination-Ref ua.co.rufous.server.services.WorkerServiceImpl/[email protected]@null into class ua.co.rufous.server.services.WorkerServiceImpl at com.sun.enterprise.container.common.impl.util.InjectionManagerImpl._inject(InjectionManagerImpl.java:614) at com.sun.enterprise.container.common.impl.util.InjectionManagerImpl.inject(InjectionManagerImpl.java:384) at com.sun.enterprise.container.common.impl.util.InjectionManagerImpl.injectInstance(InjectionManagerImpl.java:141) at com.sun.enterprise.container.common.impl.util.InjectionManagerImpl.injectInstance(InjectionManagerImpl.java:127) at com.sun.enterprise.container.common.impl.util.InjectionManagerImpl.createManagedObject(InjectionManagerImpl.java:306) ... 27 more Caused by: com.sun.enterprise.container.common.spi.util.InjectionException: Illegal use of static field private static javax.jms.Queue ua.co.rufous.server.services.WorkerServiceImpl.queue on class that only supports instance-based injection at com.sun.enterprise.container.common.impl.util.InjectionManagerImpl._inject(InjectionManagerImpl.java:532) ... 31 more |#] my MDB : /** * asadmin commands * asadmin create-jms-resource --restype javax.jms.ConnectionFactory jms/Tarturus * asadmin create-jms-resource --restype javax.jms.Queue jms/StyxMDB * asadmin list-jms-resources */ @MessageDriven(mappedName = "jms/StyxMDB", activationConfig = { @ActivationConfigProperty(propertyName = "connectionFactoryJndiName", propertyValue = "jms/Tarturus"), @ActivationConfigProperty(propertyName = "acknowledgeMode", propertyValue = "Auto-acknowledge"), @ActivationConfigProperty(propertyName = "destinationType", propertyValue = "javax.jms.Queue") }) public class StyxMDB implements MessageListener { @EJB private ActivationProcessingLocal aProcessing; public StyxMDB() { } public void onMessage(Message message) { try { TextMessage msg = (TextMessage) message; String hash = msg.getText(); GluttonyLogger.getInstance().writeInfoLog("geted jms message hash = " + hash); } catch (JMSException e) { } } } everything work good without static declaration: @Resource(mappedName = "jms/Tarturus") private ConnectionFactory connectionFactory; @Resource(mappedName = "jms/StyxMDB") private Queue queue; private Connection connection; Question 2: what is the best practice for working with MDB : processing full request in onMessage() or calling another bean(Stateless bean in my case) in onMessage() method that would process it. Processing including few calls to soap services, so the full processing time could be for a 3 seconds. Thank you.

  Read the article

• Synchronized Enumerator in C#

  - by Dan Bryant

  I'm putting together a custom SynchronizedCollection<T> class so that I can have a synchronized Observable collection for my WPF application. The synchronization is provided via a ReaderWriterLockSlim, which, for the most part, has been easy to apply. The case I'm having trouble with is how to provide thread-safe enumeration of the collection. I've created a custom IEnumerator<T> nested class that looks like this: private class SynchronizedEnumerator : IEnumerator<T> { private SynchronizedCollection<T> _collection; private int _currentIndex; internal SynchronizedEnumerator(SynchronizedCollection<T> collection) { _collection = collection; _collection._lock.EnterReadLock(); _currentIndex = -1; } #region IEnumerator<T> Members public T Current { get; private set;} #endregion #region IDisposable Members public void Dispose() { var collection = _collection; if (collection != null) collection._lock.ExitReadLock(); _collection = null; } #endregion #region IEnumerator Members object System.Collections.IEnumerator.Current { get { return Current; } } public bool MoveNext() { var collection = _collection; if (collection == null) throw new ObjectDisposedException("SynchronizedEnumerator"); _currentIndex++; if (_currentIndex >= collection.Count) { Current = default(T); return false; } Current = collection[_currentIndex]; return true; } public void Reset() { if (_collection == null) throw new ObjectDisposedException("SynchronizedEnumerator"); _currentIndex = -1; Current = default(T); } #endregion } My concern, however, is that if the Enumerator is not Disposed, the lock will never be released. In most use cases, this is not a problem, as foreach should properly call Dispose. It could be a problem, however, if a consumer retrieves an explicit Enumerator instance. Is my only option to document the class with a caveat implementer reminding the consumer to call Dispose if using the Enumerator explicitly or is there a way to safely release the lock during finalization? I'm thinking not, since the finalizer doesn't even run on the same thread, but I was curious if there other ways to improve this.

  Read the article

• realtime logging

  - by Ion Todirel

  I have an application which has a loop, part of a "Scheduler", which runs at all time and is the heart of the application. Pretty much like a game loop, just that my application is a WPF application and it's not a game. Naturally the application does logging at many points, but the Scheduler does some sensitive monitoring, and sometimes it's impossible just from the logs to tell what may have gotten wrong (and by wrong I don't mean exceptions) or the current status. Because Scheduler's inner loop runs at short intervals, you can't do file I/O-based logging (or using the Event Viewer) in there. First, you need to watch it in real-time, and secondly the log file would grow in size very fast. So I was thinking of ways to show this data to the user in the realtime, some things I considered: Display the data in realtime in the UI Use AllocConsole/WriteConsole to display this information in a console Use a different console application which would display this information, communicate between the Scheduler and the console app using pipes or other IPC techniques Use Windows' Performance Monitor and somehow feed it with this information ETW Displaying in the UI would have its issues. First it doesn't integrate with the UI I had in mind for my application, and I don't want to complicate the UI just for this. This diagnostics would only happen rarely. Secondly, there is going to be some non-trivial data protection, as the Scheduler has it's own thread. A separate console window would work probably, but I'm still worried if it's not too much threshold. Allocating my own console, as this is a windows app, would probably be better than a different console application (3), as I don't need to worry about IPC communication, and non-blocking communication. However a user could close the console I allocated, and it would be problematic in that case. With a separate process you don't have to worry about it. Assuming there is an API for Performance Monitor, it wouldn't be integrated too well with my app or apparent to the users. Using ETW also doesn't solve anything, just a random idea, I still need to display this information somehow. What others think, would there be other ways I missed?

  Read the article

• How to run a powershell script within a DOS batch file

  - by Don Vince

  How do I have a powershell script embedded within the same file as a DOS batch script? I know this kind of thing is possible in other scenarios: Embedding SQL in a DOS batch script using sqlcmd and a clever arrangements of goto's and comments at the beginning of the file In a *nix environment having a the name of the program you wish to run the script with on the first line of the script commented out e.g. #!/usr/local/bin/python There may not be a way to do this - in which case I will have to call the separate powershell script from the launching DOS script. One possible solution I've considered is to echo out the powershell script, and then run it. A good reason to not do this is that part of the reason to attempt this is to be using the advantages of the powershell environment without the pain of, for example, DOS escape characters I have some unusual constraints and would like to find an elegant solution. I suspect this question may be baiting responses of the variety: "why don't you try and solve this different problem instead." Suffice to say these are my constraints, sorry about that. Any ideas? Is there a suitable combination of clever comments and escape characters that will enable me to achieve this? Some thoughts on how to achieve this: A carat ^ at the end of a line in DOS is a continuation - like an underscore in VB An ampersand & in DOS typically is used to separate commands echo Hello & echo World results in 2 echos on separate lines %0 will give you the script that's currently running So something like this (if I could make it work) would be good: # & call powershell -psconsolefile %0 # & goto :EOF /* From here on in we're running nice juicy powershell code */ Write-Output "Hello World" Except... It doesn't work... because the extension of the file isn't as per powershell's liking: Windows PowerShell console file "insideout.bat" extension is not psc1. Windows PowerShell console file extension must be psc1. DOS isn't really altogether happy with the situation either - although it does stumble on '#' is not recognized as an internal or external command, operable program or batch file.

  Read the article

• What is the safe way to use fork with Apache::DBI under mod_perl2?

  - by codeholic

  I have a problem when I use Apache::DBI in child processes. The problem is that Apache::DBI provides a single handle for all processes which use it, so I get DBD::mysql::db selectall_arrayref failed: Commands out of sync; you can't run this command now at /usr/local/www/apache22/data/test-fork.cgi line 20. Reconnection doesn't help, since Apache::DBI reconnects in all processes, as I understood the following error The server encountered an internal error and was unable to complete your request. Error message: DBD driver has not implemented the AutoCommit attribute at /usr/local/lib/perl5/site_perl/5.8.9/Apache/DBI.pm line 283. , Here's the origin code: use Data::Dumper 'Dumper'; use DBI (); my $dbh = DBI->connect($dsn, $username, $password, { RaiseError => 1, PrintError => 0, }); my $file = "/tmp/test-fork.tmp"; my $pid = fork; defined $pid or die "fork: $!"; if ($pid) { my $rows = eval { $dbh->selectall_arrayref('SELECT SLEEP(1)') }; print "Content-Type: text/plain\n\n"; print $rows ? "parent: " . Dumper($rows) : $@; } else { my $rows = eval { $dbh->selectall_arrayref('SELECT SLEEP(1)') }; open FH, '>', $file or die "$file: $!"; print FH $rows ? "child: " . Dumper($rows) : $@; close FH; } The code I used for reconnection: ... else { $dbh->disconnect; $dbh = DBI->connect($dsn, $username, $password, $attrs); my $rows = eval { $dbh->selectall_arrayref('SELECT SLEEP(1)') }; open FH, '>', $file or die "$file: $!"; print FH $rows ? "child: " . Dumper($rows) : $@; close FH; } Is there a safe way to use Apache::DBI with forking? Is there a way to make it create a new connection perhaps?

  Read the article

• Django: CharField with fixed length, how?

  - by Giovanni Di Milia

  Hi everybody, I wold like to have in my model a CharField with fixed length. In other words I want that only a specified length is valid. I tried to do something like volumenumber = models.CharField('Volume Number', max_length=4, min_length=4) but it gives me an error (it seems that I can use both max_length and min_length at the same time). Is there another quick way? Thanks EDIT: Following the suggestions of some people I will be a bit more specific: My model is this: class Volume(models.Model): vid = models.AutoField(primary_key=True) jid = models.ForeignKey(Journals, db_column='jid', null=True, verbose_name = "Journal") volumenumber = models.CharField('Volume Number') date_publication = models.CharField('Date of Publication', max_length=6, blank=True) class Meta: db_table = u'volume' verbose_name = "Volume" ordering = ['jid', 'volumenumber'] unique_together = ('jid', 'volumenumber') def __unicode__(self): return (str(self.jid) + ' - ' + str(self.volumenumber)) What I want is that the volumenumber must be exactly 4 characters. I.E. if someone insert '4b' django gives an error because it expects a string of 4 characters. So I tried with volumenumber = models.CharField('Volume Number', max_length=4, min_length=4) but it gives me this error: Validating models... Unhandled exception in thread started by <function inner_run at 0x70feb0> Traceback (most recent call last): File "/Library/Python/2.5/site-packages/django/core/management/commands/runserver.py", line 48, in inner_run self.validate(display_num_errors=True) File "/Library/Python/2.5/site-packages/django/core/management/base.py", line 249, in validate num_errors = get_validation_errors(s, app) File "/Library/Python/2.5/site-packages/django/core/management/validation.py", line 28, in get_validation_errors for (app_name, error) in get_app_errors().items(): File "/Library/Python/2.5/site-packages/django/db/models/loading.py", line 131, in get_app_errors self._populate() File "/Library/Python/2.5/site-packages/django/db/models/loading.py", line 58, in _populate self.load_app(app_name, True) File "/Library/Python/2.5/site-packages/django/db/models/loading.py", line 74, in load_app models = import_module('.models', app_name) File "/Library/Python/2.5/site-packages/django/utils/importlib.py", line 35, in import_module __import__(name) File "/Users/Giovanni/src/djangoTestSite/../djangoTestSite/journaldb/models.py", line 120, in <module> class Volume(models.Model): File "/Users/Giovanni/src/djangoTestSite/../djangoTestSite/journaldb/models.py", line 123, in Volume volumenumber = models.CharField('Volume Number', max_length=4, min_length=4) TypeError: __init__() got an unexpected keyword argument 'min_length' That obviously doesn't appear if I use only "max_length" OR "min_length". I read the documentation on the django web site and it seems that I'm right (I cannot use both together) so I'm asking if there is another way to solve the problem. Thanks again

  Read the article

• C# SerialPort - Problems mixing ports with different baud rates.

  - by GrandAdmiral

  Greetings, I have two devices that I would like to connect over a serial interface, but they have incompatible connections. To get around this problem, I connected them both to my PC and I'm working on a C# program that will route traffic on COM port X to COM port Y and vice versa. The program connects to two COM ports. In the data received event handler, I read in incoming data and write it to the other COM port. To do this, I have the following code: private void HandleDataReceived(SerialPort inPort, SerialPort outPort) { byte[] data = new byte[1]; while (inPort.BytesToRead > 0) { // Read the data data[0] = (byte)inPort.ReadByte(); // Write the data if (outPort.IsOpen) { outPort.Write(data, 0, 1); } } } That code worked fine as long as the outgoing COM port operated at a higher baud rate than the incoming COM port. If the incoming COM port was faster than the outgoing COM port, I started missing data. I had to correct the code like this: private void HandleDataReceived(SerialPort inPort, SerialPort outPort) { byte[] data = new byte[1]; while (inPort.BytesToRead > 0) { // Read the data data[0] = (byte)inPort.ReadByte(); // Write the data if (outPort.IsOpen) { outPort.Write(data, 0, 1); while (outPort.BytesToWrite > 0); //<-- Change to fix problem } } } I don't understand why I need that fix. I'm new to C# (this is my first program), so I'm wondering if there is something I am missing. The SerialPort defaults to a 2048 byte write buffer and my commands are less than ten bytes. The write buffer should have the ability to buffer the data until it can be written to a slower COM port. In summary, I'm receiving data on COM X and writing the data to COM Y. COM X is connected at a faster baud rate than COM Y. Why doesn't the buffering in the write buffer handle this difference? Why does it seem that I need to wait for the write buffer to drain to avoid losing data? Thanks!

  Read the article

• OpenCV 2.4.2 on Matlab 2012b (Windows 7)

  - by Maik Xhani

  Hello i am trying to use OpenCV 2.4.2 in Matlab 2012b. I have tried those actions: downloaded OpenCV 2.4.2 used CMake on opencv folder using Visual Studio 10 and Visual Studio 10 Win64 compiler built Debug and Release version with Visual Studio first without any other option and then with D_SCL_SECURE=1 specified for every project changed Matlab's mexopts.bat and adding new lines refering to library and include (see bottom for mexopts.bat content) with Visual Studio 10 compiler tried to compile a simple file with a OpenCV library inclusion and all goes well. try to compile something that actually uses OpenCV commands and get errors. I used openmexopencv library and when tried to compile something i get this error cv.make mex -largeArrayDims -D_SECURE_SCL=1 -Iinclude -I"C:\OpenCV\build\include" -L"C:\OpenCV\build\x64\vc10\lib" -lopencv_calib3d242 -lopencv_contrib242 -lopencv_core242 -lopencv_features2d242 -lopencv_flann242 -lopencv_gpu242 -lopencv_haartraining_engine -lopencv_highgui242 -lopencv_imgproc242 -lopencv_legacy242 -lopencv_ml242 -lopencv_nonfree242 -lopencv_objdetect242 -lopencv_photo242 -lopencv_stitching242 -lopencv_ts242 -lopencv_video242 -lopencv_videostab242 src+cv\CamShift.cpp lib\MxArray.obj -output +cv\CamShift CamShift.cpp C:\Program Files\MATLAB\R2012b\extern\include\tmwtypes.h(821) : warning C4091: 'typedef ': ignorato a sinistra di 'wchar_t' quando non si dichiara alcuna variabile c:\program files\matlab\r2012b\extern\include\matrix.h(319) : error C4430: identificatore di tipo mancante, verr… utilizzato int. Nota: default-int non Š pi— supportato in C++ the content of my mexopts.bat is @echo off rem MSVC100OPTS.BAT rem rem Compile and link options used for building MEX-files rem using the Microsoft Visual C++ compiler version 10.0 rem rem $Revision: 1.1.6.4.2.1 $ $Date: 2012/07/12 13:53:59 $ rem Copyright 2007-2009 The MathWorks, Inc. rem rem StorageVersion: 1.0 rem C++keyFileName: MSVC100OPTS.BAT rem C++keyName: Microsoft Visual C++ 2010 rem C++keyManufacturer: Microsoft rem C++keyVersion: 10.0 rem C++keyLanguage: C++ rem C++keyLinkerName: Microsoft Visual C++ 2010 rem C++keyLinkerVersion: 10.0 rem rem ******************************************************************** rem General parameters rem ******************************************************************** set MATLAB=%MATLAB% set VSINSTALLDIR=c:\Program Files (x86)\Microsoft Visual Studio 10.0 set VCINSTALLDIR=%VSINSTALLDIR%\VC set OPENCVDIR=C:\OpenCV rem In this case, LINKERDIR is being used to specify the location of the SDK set LINKERDIR=c:\Program Files (x86)\Microsoft SDKs\Windows\v7.0A\ set PATH=%VCINSTALLDIR%\bin\amd64;%VCINSTALLDIR%\bin;%VCINSTALLDIR%\VCPackages;%VSINSTALLDIR%\Common7\IDE;%VSINSTALLDIR%\Common7\Tools;%LINKERDIR%\bin\x64;%LINKERDIR%\bin;%MATLAB_BIN%;%PATH% set INCLUDE=%OPENCVDIR%\build\include;%VCINSTALLDIR%\INCLUDE;%VCINSTALLDIR%\ATLMFC\INCLUDE;%LINKERDIR%\include;%INCLUDE% set LIB=%OPENCVDIR%\build\x64\vc10\lib;%VCINSTALLDIR%\LIB\amd64;%VCINSTALLDIR%\ATLMFC\LIB\amd64;%LINKERDIR%\lib\x64;%MATLAB%\extern\lib\win64;%LIB% set MW_TARGET_ARCH=win64 rem ******************************************************************** rem Compiler parameters rem ******************************************************************** set COMPILER=cl set COMPFLAGS=/c /GR /W3 /EHs /D_CRT_SECURE_NO_DEPRECATE /D_SCL_SECURE_NO_DEPRECATE /D_SECURE_SCL=0 /DMATLAB_MEX_FILE /nologo /MD set OPTIMFLAGS=/O2 /Oy- /DNDEBUG set DEBUGFLAGS=/Z7 set NAME_OBJECT=/Fo rem ******************************************************************** rem Linker parameters rem ******************************************************************** set LIBLOC=%MATLAB%\extern\lib\win64\microsoft set LINKER=link set LINKFLAGS=/dll /export:%ENTRYPOINT% /LIBPATH:"%LIBLOC%" libmx.lib libmex.lib libmat.lib /MACHINE:X64 kernel32.lib user32.lib gdi32.lib winspool.lib comdlg32.lib advapi32.lib shell32.lib ole32.lib oleaut32.lib uuid.lib odbc32.lib odbccp32.lib opencv_calib3d242.lib opencv_contrib242.lib opencv_core242.lib opencv_features2d242.lib opencv_flann242.lib opencv_gpu242.lib opencv_haartraining_engine.lib opencv_imgproc242.lib opencv_highgui242.lib opencv_legacy242.lib opencv_ml242.lib opencv_nonfree242.lib opencv_objdetect242.lib opencv_photo242.lib opencv_stitching242.lib opencv_ts242.lib opencv_video242.lib opencv_videostab242.lib /nologo /manifest /incremental:NO /implib:"%LIB_NAME%.x" /MAP:"%OUTDIR%%MEX_NAME%%MEX_EXT%.map" set LINKOPTIMFLAGS= set LINKDEBUGFLAGS=/debug /PDB:"%OUTDIR%%MEX_NAME%%MEX_EXT%.pdb" set LINK_FILE= set LINK_LIB= set NAME_OUTPUT=/out:"%OUTDIR%%MEX_NAME%%MEX_EXT%" set RSP_FILE_INDICATOR=@ rem ******************************************************************** rem Resource compiler parameters rem ******************************************************************** set RC_COMPILER=rc /fo "%OUTDIR%mexversion.res" set RC_LINKER= set POSTLINK_CMDS=del "%LIB_NAME%.x" "%LIB_NAME%.exp" set POSTLINK_CMDS1=mt -outputresource:"%OUTDIR%%MEX_NAME%%MEX_EXT%;2" -manifest "%OUTDIR%%MEX_NAME%%MEX_EXT%.manifest" set POSTLINK_CMDS2=del "%OUTDIR%%MEX_NAME%%MEX_EXT%.manifest" set POSTLINK_CMDS3=del "%OUTDIR%%MEX_NAME%%MEX_EXT%.map"

  Read the article

• South migration error: NoMigrations exception for django.contrib.auth

  - by danpalmer

  I have been using South on my project for a while, but I recently did a huge amount of development and changed development machine and I think something messed up in the process. The project works fine, but I can't apply migrations. Whenever I try to apply a migration I get the following traceback: danpalmer:pest Dan$ python manage.py migrate frontend Traceback (most recent call last): File "manage.py", line 11, in <module> execute_manager(settings) File "/Library/Python/2.6/site-packages/django/core/management/__init__.py", line 362, in execute_manager utility.execute() File "/Library/Python/2.6/site-packages/django/core/management/__init__.py", line 303, in execute self.fetch_command(subcommand).run_from_argv(self.argv) File "/Library/Python/2.6/site-packages/django/core/management/base.py", line 195, in run_from_argv self.execute(*args, **options.__dict__) File "/Library/Python/2.6/site-packages/django/core/management/base.py", line 222, in execute output = self.handle(*args, **options) File "/Library/Python/2.6/site-packages/South-0.7-py2.6.egg/south/management/commands/migrate.py", line 102, in handle delete_ghosts = delete_ghosts, File "/Library/Python/2.6/site-packages/South-0.7-py2.6.egg/south/migration/__init__.py", line 182, in migrate_app applied = check_migration_histories(applied, delete_ghosts) File "/Library/Python/2.6/site-packages/South-0.7-py2.6.egg/south/migration/__init__.py", line 85, in check_migration_histories m = h.get_migration() File "/Library/Python/2.6/site-packages/South-0.7-py2.6.egg/south/models.py", line 34, in get_migration return self.get_migrations().migration(self.migration) File "/Library/Python/2.6/site-packages/South-0.7-py2.6.egg/south/models.py", line 31, in get_migrations return Migrations(self.app_name) File "/Library/Python/2.6/site-packages/South-0.7-py2.6.egg/south/migration/base.py", line 60, in __call__ self.instances[app_label] = super(MigrationsMetaclass, self).__call__(app_label_to_app_module(app_label), **kwds) File "/Library/Python/2.6/site-packages/South-0.7-py2.6.egg/south/migration/base.py", line 88, in __init__ self.set_application(application, force_creation, verbose_creation) File "/Library/Python/2.6/site-packages/South-0.7-py2.6.egg/south/migration/base.py", line 159, in set_application raise exceptions.NoMigrations(application) south.exceptions.NoMigrations: Application '<module 'django.contrib.auth' from '/Library/Python/2.6/site-packages/django/contrib/auth/__init__.pyc'>' has no migrations. I am not that experienced with South and I haven't met this error before. The only helpful mention I can find online about this error is for pre-0.7 I think and I am on South 0.7. I ran 'easy_install -U South' just to make sure. Thanks for any help that you can provide. I really appreciate it.

  Read the article

• .NET SerialPort DataReceived event thread interference with main thread

  - by Kiran

  I am writing a serial communication program using the SerialPort class in C# to interact with a strip machine connected via a RS232 cable. When i send the command to the machine it responds with some bytes depending on the command. Like when i send a "\D" command, i am expecting to download the machine program data of 180 bytes as a continous string. As per the machine's manual, it suggests as a best practice to send an unreognized characters like comma (,) character to make sure the machine is initialized before sending the first command in the cycle. My serial communication code is as follows: public class SerialHelper { SerialPort commPort = null; string currentReceived = string.Empty; string receivedStr = string.Empty; private bool CommInitialized() { try { commPort = new SerialPort(); commPort.PortName = "COM1"; if (!commPort.IsOpen) commPort.Open(); commPort.BaudRate = 9600; commPort.Parity = System.IO.Ports.Parity.None; commPort.StopBits = StopBits.One; commPort.DataBits = 8; commPort.RtsEnable = true; commPort.DtrEnable = true; commPort.DataReceived += new SerialDataReceivedEventHandler(commPort_DataReceived); return true; } catch (Exception ex) { return false; } } void commPort_DataReceived(object sender, SerialDataReceivedEventArgs e) { SerialPort currentPort = (SerialPort)sender; currentReceived = currentPort.ReadExisting(); receivedStr += currentReceived; } internal int CommIO(string outString, int outLen, ref string inBuffer, int inLen) { receivedStr = string.Empty; inBuffer = string.Empty; if (CommInitialized()) { commPort.Write(outString); } System.Threading.Thread.Sleep(1500); int i = 0; while ((receivedStr.Length < inLen) && i < 10) { System.Threading.Thread.Sleep(500); i += 1; } if (!string.IsNullOrEmpty(receivedStr)) { inBuffer = receivedStr; } commPort.Close(); return inBuffer.Length; } } I am calling this code from a windows form as follows: len = SerialHelperObj.CommIO(",",1,ref inBuffer, 4) len = SerialHelperObj.CommIO(",",1,ref inBuffer, 4) If(inBuffer == "!?*O") { len = SerialHelperObj.CommIO("\D",2,ref inBuffer, 180) } A valid return value from the serial port looks like this: \D00000010000000000010 550 3250 0000256000 and so on ... I am getting some thing like this: \D00000010D,, 000 550 D,, and so on... I feel that my comm calls are getting interferred with the one when i send commands. But i am trying to make sure the result of the comma command then initiating the actual command. but the received thread is inserting the bytes from the previous communication cycle. Can any one please shed some light into this...? I lost quite some hair just trying to get this work. I am not sure where i am doing wrong

  Read the article

• How do I prevent the concurrent execution of a javascript function?

  - by RyanV

  I am making a ticker similar to the "From the AP" one at The Huffington Post, using jQuery. The ticker rotates through a ul, either by user command (clicking an arrow) or by an auto-scroll. Each list-item is display:none by default. It is revealed by the addition of a "showHeadline" class which is display:list-item. HTML for the UL Looks like this: <ul class="news" id="news"> <li class="tickerTitle showHeadline">Test Entry</li> <li class="tickerTitle">Test Entry2</li> <li class="tickerTitle">Test Entry3</li> </ul> When the user clicks the right arrow, or the auto-scroll setTimeout goes off, it runs a tickForward() function: function tickForward(){ var $active = $('#news li.showHeadline'); var $next = $active.next(); if($next.length==0) $next = $('#news li:first'); $active.stop(true, true); $active.fadeOut('slow', function() {$active.removeClass('showHeadline');}); setTimeout(function(){$next.fadeIn('slow', function(){$next.addClass('showHeadline');})}, 1000); if(isPaused == true){ } else{ startScroll() } }; This is heavily inspired by Jon Raasch's A Simple jQuery Slideshow. Basically, find what's visible, what should be visible next, make the visible thing fade and remove the class that marks it as visible, then fade in the next thing and add the class that makes it visible. Now, everything is hunky-dory if the auto-scroll is running, kicking off tickForward() once every three seconds. But if the user clicks the arrow button repeatedly, it creates two negative conditions: Rather than advance quickly through the list for just the number of clicks made, it continues scrolling at a faster-than-normal rate indefinitely. It can produce a situation where two (or more) list items are given the .showHeadline class, so there's overlap on the list. I can see these happening (especially #2) because the tickForward() function can run concurrently with itself, producing different sets of $active and $next. So I think my question is: What would be the best way to prevent concurrent execution of the tickForward() method? Some things I have tried or considered: Setting a Flag: When tickForward() runs, it sets an isRunning flag to true, and sets it back to false right before it ends. The logic for the event handler is set to only call tickForward() if isRunning is false. I tried a simple implementation of this, and isRunning never appeared to be changed. The jQuery queue(): I think it would be useful to queue up the tickForward() commands, so if you clicked it five times quickly, it would still run as commanded but wouldn't run concurrently. However, in my cursory reading on the subject, it appears that a queue has to be attached to the object its queue applies to, and since my tickForward() method affects multiple lis, I don't know where I'd attach it.

  Read the article

• Mercurial over ssh client and server on Windows

  - by Ben Von Handorf

  I'm trying to configure Mercurial for use with both a windows server (freeSSHd) and client (both command line and TortoiseHG). I'm using the most recent versions of everything... all downloaded in the past few days. Using public key auth, I have been able to get connected to the server and I'm able to use plink to execute "hg version" and get a response, but when I try to clone a repository from the ssh server the command appears to hang. Running with -v yields: hg -v clone ssh://<username>@<server>//hg/repositoryA testRepositoryA running "plink.exe -i "<path to private key file>" <username>@<server> "hg -R /hg/repositoryA serve --stdio"" with nothing more forthcoming. Running the hg serve command directly on the server yields an apparently responsive Mercurial server, but the clients do not seem to make any further requests. Running "hg serve" in the repository directory and cloning over http works perfectly. What should I be looking for to help debug this? Is there something the clients (hg and TortoiseHG) aren't sending to continue the request stream? Additional Information: If I change to an invalid repository on the target machine, the appropriate error is displayed, so it does appear that the remote hg is running and correctly evaluating the path. Running with --debug and --traceback results in: sending hello command sending between command It hangs here, until I CTRL-C Traceback (most recent call last): File "mercurial\dispatch.pyo", line 46, in _runcatch File "mercurial\dispatch.pyo", line 452, in _dispatch File "mercurial\dispatch.pyo", line 320, in runcommand File "mercurial\dispatch.pyo", line 504, in _runcommand File "mercurial\dispatch.pyo", line 457, in checkargs File "mercurial\dispatch.pyo", line 451, in <lambda> File "mercurial\util.pyo", line 402, in check File "mercurial\commands.pyo", line 636, in clone File "mercurial\hg.pyo", line 187, in clone File "mercurial\hg.pyo", line 63, in repository File "mercurial\sshrepo.pyo", line 51, in __init__ File "mercurial\sshrepo.pyo", line 73, in validate_repo KeyboardInterrupt interrupted! Responding to Ryan: There does not appear to be any CPU usage or increasing memory usage on the server. It appears to be waiting for the client to send a request or something similar. 11/19/2009 : More information: The problem is definitely in the freeSSHd/server side of the equation. Connecting to bitbucket over ssh with the same keyset works fine. Still working on this.

  Read the article

< Previous Page | 417 418 419 420 421 422 423 424 425 426 427 428  | Next Page >