login attempts - Page 422

Wrapping a point-to-point link

- by user3712955

I'm using a pair of IP radios (non-WiFi) to bridge my office engineering LAN (172.0.0.0/8) to a lab in another building. The radios work fine, but they expose a web management interface I'd like to hide, and they also generate traffic (ARP, STP, and more) that I need to keep off my (very, very clean) LAN segments. I have some ARM-Linux boards (similar to Beagle/Panda/RasPi) running Ubuntu, and I've put one at each end of the link, between the radio and the LAN. Each of the boards has 2 wired Ethernet interfaces, eth0 and eth1. The LAN segments are connected to eth0, and the radios are connected to eth1. I'd like to accomplish the following: Keep radio-originated traffic off my LAN segments! Hide all services provided by the radio (web, ssh, etc.) Transparently pass all traffic between the LAN segments (including things like ARP). The above also applies to the ARM-Linux boards: No stray traffic my LAN from them either! I'd like the system to look like a switch: LAN packets arriving at one eth0 appear at the other. And neither eth0 should have an IP address: The working system should behave like a CAT6 cable with some latency (instead of ARM boards and radios). Unfortunately, I'm confused about how to properly configure the ARM Ubuntu systems. What I'm guessing I need is a bridge on each board (br0?) and a VLAN (vlan0 or eth0.0?) to isolate the LAN traffic from everything else as it passes through the ARM boards and the radios. Then I need some kind of a firewall to block sending anything out eth0 that isn't from the other eth0 (via the VLAN). I've looked at the ip and ebtables commands (especially -t broute). While the concepts sorta-kinda make sense, I'm completely lost in the details. Edit: In the perverse case that a system on one of my LAN segments has the same IP address as one of the radios, or as eth1 on the ARM-Ubuntu boards, a VLAN won't work. Which I believe means I need to tunnel all traffic between the two eth0 interfaces to get that "like a wire" behavior. Help? Finally, I'd like to have a way to temporarily expose services on the ARM boards (ssh) and the radios (web) for maintenance purposes. Ideally, it would expose an IP address with ssh available on port 22. Once connected, I figure I'd start an X11 session and run a browser on the ARM board to access the radios. Or something. I could login via the console to enable/disable this, or perhaps could use a GPIO to trigger a script. I feel I've identified most of the pieces needed to make all this happen, but I have no idea how to combine them to make a working system. Thanks!

Read the article

C# Bind DataTable to Existing DataGridView Column Definitions

- by Timothy

I've been struggling with a NullReferenceException and hope someone here will be able to point me in the right direction. I'm trying to create and populate a DataTable and then show the results in a DataGridView control. The basic code follows, and Execution stops with a NullReferenceException at the point where I invoke the new UpdateResults_Delegate. Oddly enough, I can trace entries.Rows.Count successfully before I return it from QueryEventEntries, so I can at least show 1) entries is not a null reference, and 2) the DataTable contains rows of data. I know I have to be doing something wrong, but I just don't know what. private void UpdateResults(DataTable entries) { dataGridView.DataSource = entries; } private void button_Click(object sender, EventArgs e) { PerformQuery(); } private void PerformQuery() { DateTime start = new DateTime(dateTimePicker1.Value.Year, dateTimePicker1.Value.Month, dateTimePicker1.Value.Day, 0, 0, 0); DateTime stop = new DateTime(dateTimePicker2.Value.Year, dateTimePicker2.Value.Month, dateTimePicker2.Value.Day, 0, 0, 0); DataTable entries = QueryEventEntries(start, stop); UpdateResults(entries); } private DataTable QueryEventEntries(DateTime start, DateTime stop) { DataTable entries = new DataTable(); entries.Columns.AddRange(new DataColumn[] { new DataColumn("event_type", typeof(Int32)), new DataColumn("event_time", typeof(DateTime)), new DataColumn("event_detail", typeof(String))}); using (SqlConnection conn = new SqlConnection(DSN)) { using (SqlDataAdapter adapter = new SqlDataAdapter( "SELECT event_type, event_time, event_detail FROM event_log " + "WHERE event_time >= @start AND event_time <= @stop", conn)) { adapter.SelectCommand.Parameters.AddRange(new Object[] { new SqlParameter("@start", start), new SqlParameter("@stop", stop)}); adapter.Fill(entries); } } return entries; } Update I'd like to summarize and provide some additional information I've learned from the discussion here and debugging efforts since I originally posted this question. I am refactoring old code that retrieved records from a database, collected those records as an array, and then later iterated through the array to populate a DataGridView row by row. Threading was originally implemented to compensate and keep the UI responsive during the unnecessary looping. I have since stripped out Thread/Invoke; everything now occurs on the same execution thread (thank you, Sam). I am attempting to replace the slow, unwieldy approach using a DataTable which I can fill with a DataAdapter, and assign to the DataGridView through it's DataSource property (above code updated). I've iterated through the entries DataTable's rows to verify the table contains the expected data before assigning it as the DataGridView's DataSource. foreach (DataRow row in entries.Rows) { System.Diagnostics.Trace.WriteLine( String.Format("{0} {1} {2}", row[0], row[1], row[2])); } One of the column of the DataGridView is a custom DataGridViewColumn to stylize the event_type value. I apologize I didn't mention this before in the original post but I wasn't aware it was important to my problem. I have converted this column temporarily to a standard DataGridViewTextBoxColumn control and am no longer experiencing the Exception. The fields in the DataTable are appended to the list of fields that have been pre-specified in Design view of the DataGridView. The records' values are being populated in these appended fields. When the run time attempts to render the cell a null value is provided (as the value that should be rendered is done so a couple columns over). In light of this, I am re-titling and re-tagging the question. I would still appreciate it if others who have experienced this can instruct me on how to go about binding the DataTable to the existing column definitions of the DataGridView.

Read the article

Why does WPF Style to show validation errors in ToolTip work for a TextBox but fails for a ComboBox?

- by Mike B

I am using a typical Style to display validation errors as a tooltip from IErrorDataInfo for a textbox as shown below and it works fine. <Style TargetType="{x:Type TextBox}"> <Style.Triggers> <Trigger Property="Validation.HasError" Value="true"> <Setter Property="ToolTip" Value="{Binding RelativeSource={RelativeSource Self}, Path=(Validation.Errors)[0].ErrorContent}"/> </Trigger> </Style.Triggers> </Style> But when i try to do the same thing for a ComboBox like this it fails <Style TargetType="{x:Type ComboBox}"> <Style.Triggers> <Trigger Property="Validation.HasError" Value="true"> <Setter Property="ToolTip" Value="{Binding RelativeSource={RelativeSource Self}, Path=(Validation.Errors)[0].ErrorContent}"/> </Trigger> </Style.Triggers> </Style> The error I get in the output window is: System.Windows.Data Error: 17 : Cannot get 'Item[]' value (type 'ValidationError') from '(Validation.Errors)' (type 'ReadOnlyObservableCollection`1'). BindingExpression:Path=(0)[0].ErrorContent; DataItem='ComboBox' (Name='ownerComboBox'); target element is 'ComboBox' (Name='ownerComboBox'); target property is 'ToolTip' (type 'Object') ArgumentOutOfRangeException:'System.ArgumentOutOfRangeException: Specified argument was out of the range of valid values.Parameter name: index' Oddly it also attempts to make invalid Database changes when I close the window if I change any ComboBox values (This is also when the binding error occurs)!!! Cannot insert the value NULL into column 'EmpFirstName', table 'OITaskManager.dbo.Employees'; column does not allow nulls. INSERT fails. The statement has been terminated. Simply by commenting the style out everyting works perfectly. How do I fix this? Just in case anyone needs it one of the comboBox' xaml follows: <ComboBox ItemsSource="{Binding Path=Employees}" SelectedValuePath="EmpID" SelectedValue="{Binding Path=SelectedIssue.Employee2.EmpID, Mode=OneWay, ValidatesOnDataErrors=True}" ItemTemplate="{StaticResource LastNameFirstComboBoxTemplate}" Height="28" Name="ownerComboBox" Width="120" Margin="2" SelectionChanged="ownerComboBox_SelectionChanged" /> <DataTemplate x:Key="LastNameFirstComboBoxTemplate"> <TextBlock> <TextBlock.Text> <MultiBinding StringFormat="{}{1}, {0}" > <Binding Path="EmpFirstName" /> <Binding Path="EmpLastName" /> </MultiBinding> </TextBlock.Text> </TextBlock> </DataTemplate> SelectionChanged: (I do plan to implement commanding before long but, as this is my first WPF project I have not gone full MVVM yet. I am trying to take things in small-medium sized bites) // This is done this way to maintain the DataContext Integrity // and avoid an error due to an Object being "Not New" in Linq-to-SQL private void ownerComboBox_SelectionChanged(object sender, SelectionChangedEventArgs e) { Employee currentEmpl = ownerComboBox.SelectedItem as Employee; if (currentEmpl != null && currentEmpl != statusBoardViewModel.SelectedIssue.Employee2) { statusBoardViewModel.SelectedIssue.Employee2 = currentEmpl; } }

Read the article

Android-Java: Constructing a triangle based on Coordinates on a map and your bearing

- by Aidan

Hi Guys, I'm constructing a geolocation based application and I'm trying to figure out a way to make my application realise when a user is facing the direction of the given location (a particular long / lat co-ord). I've got the math figured, I just have the triangle to construct. //UPDATE So I've figured out a good bit of this... Below is a method which takes in a long / lat value and attempts to compute a triangle finding a point 700 meters away and one to its left + right. It'd then use these to construct the triangle. It computes the correct longitude but the latitude ends up somewhere off the coast of east Africa. (I'm in Ireland!). public void drawtri(double currlng,double currlat, double bearing){ bearing = (bearing < 0 ? -bearing : bearing); System.out.println("RUNNING THE DRAW TRIANGLE METHOD!!!!!"); System.out.println("CURRENT LNG" + currlng); System.out.println("CURRENT LAT" + currlat); System.out.println("CURRENT BEARING" + bearing); //Find point X(x,y) double distance = 0.7; //700 meters. double R = 6371.0; //The radius of the earth. //Finding X's y value. Math.toRadians(currlng); Math.toRadians(currlat); Math.toRadians(bearing); distance = distance/R; Global.Alat = Math.asin(Math.sin(currlat)*Math.cos(distance)+ Math.cos(currlat)*Math.sin(distance)*Math.cos(bearing)); System.out.println("CURRENT ALAT!!: " + Global.Alat); //Finding X's x value. Global.Alng = currlng + Math.atan2(Math.sin(bearing)*Math.sin(distance) *Math.cos(currlat), Math.cos(distance)-Math.sin(currlat)*Math.sin(Global.Alat)); Math.toDegrees(Global.Alat); Math.toDegrees(Global.Alng); //Co-ord of Point B(x,y) // Note: Lng = X axis, Lat = Y axis. Global.Blat = Global.Alat+ 00.007931; Global.Blng = Global.Alng; //Co-ord of Point C(x,y) Global.Clat = Global.Alat - 00.007931; Global.Clng = Global.Alng; } From debugging I've determined the problem lies with the computation of the latitude done here.. Global.Alat = Math.asin(Math.sin(currlat)*Math.cos(distance)+ Math.cos(currlat)*Math.sin(distance)*Math.cos(bearing)); I have no idea why though and don't know how to fix it. I got the formula from this site.. http://www.movable-type.co.uk/scripts/latlong.html It appears correct and I've tested multiple things... I've tried converting to Radians then post computations back to degrees, etc. etc. Anyone got any ideas how to fix this method so that it will map the triangle ONLY 700 meters in from my current location in the direction that I am facing? Thanks, EDIT/// Converting the outcome to radians gives me a lat of 5.6xxxxxxxxxxxxxx .I have a feeling this bug has something to do with conversions but its not THAT simple. The equation is correct, it just.. outputs wrong..

Read the article

Need Help Setting an Image with Transparent Background to Clipboard

- by AMissico

I need help setting a transparent image to the clipboard. I keep getting "handle is invalid". Basically, I need a "second set of eyes" to look over the following code. (The complete working project at ftp://missico.net/ImageVisualizer.zip.) This is an image Debug Visualizer class library, but I made the included project to run as an executable for testing. (Note that window is a toolbox window and show in taskbar is set to false.) I was tired of having to perform a screen capture on the toolbox window, open the screen capture with an image editor, and then deleting the background added because it was a screen capture. So I thought I would quickly put the transparent image onto the clipboard. Well, the problem is...no transparency support for Clipboard.SetImage. Google to the rescue...not quite. This is what I have so far. I pulled from a number of sources. See the code for the main reference. My problem is the "invalid handle" when using CF_DIBV5. Do I need to use BITMAPV5HEADER and CreateDIBitmap? Any help from you GDI/GDI+ Wizards would be greatly appreciated. public static void SetClipboardData(Bitmap bitmap, IntPtr hDC) { const uint SRCCOPY = 0x00CC0020; const int CF_DIBV5 = 17; const int CF_BITMAP = 2; //'reference //'http://social.msdn.microsoft.com/Forums/en-US/winforms/thread/816a35f6-9530-442b-9647-e856602cc0e2 IntPtr memDC = CreateCompatibleDC(hDC); IntPtr memBM = CreateCompatibleBitmap(hDC, bitmap.Width, bitmap.Height); SelectObject(memDC, memBM); using (Graphics g = Graphics.FromImage(bitmap)) { IntPtr hBitmapDC = g.GetHdc(); IntPtr hBitmap = bitmap.GetHbitmap(); SelectObject(hBitmapDC, hBitmap); BitBlt(memDC, 0, 0, bitmap.Width, bitmap.Height, hBitmapDC, 0, 0, SRCCOPY); if (!OpenClipboard(IntPtr.Zero)) { throw new System.Runtime.InteropServices.ExternalException("Could not open Clipboard", new Win32Exception()); } if (!EmptyClipboard()) { throw new System.Runtime.InteropServices.ExternalException("Unable to empty Clipboard", new Win32Exception()); } //IntPtr hClipboard = SetClipboardData(CF_BITMAP, memBM); //works but image is not transparent //all my attempts result in SetClipboardData returning hClipboard = IntPtr.Zero IntPtr hClipboard = SetClipboardData(CF_DIBV5, memBM); //because if (hClipboard == IntPtr.Zero) { // InnerException: System.ComponentModel.Win32Exception // Message="The handle is invalid" // ErrorCode=-2147467259 // NativeErrorCode=6 // InnerException: throw new System.Runtime.InteropServices.ExternalException("Could not put data on Clipboard", new Win32Exception()); } if (!CloseClipboard()) { throw new System.Runtime.InteropServices.ExternalException("Could not close Clipboard", new Win32Exception()); } g.ReleaseHdc(hBitmapDC); } } private void __copyMenuItem_Click(object sender, EventArgs e) { using (Graphics g = __pictureBox.CreateGraphics()) { IntPtr hDC = g.GetHdc(); MemoryStream ms = new MemoryStream(); __pictureBox.Image.Save(ms, ImageFormat.Png); ms.Seek(0, SeekOrigin.Begin); Image imag = Image.FromStream(ms); // Derive BitMap object using Image instance, so that you can avoid the issue //"a graphics object cannot be created from an image that has an indexed pixel format" Bitmap img = new Bitmap(new Bitmap(imag)); SetClipboardData(img, hDC); g.ReleaseHdc(); } }

Read the article

facebook iframe stream.Publish cannot close dialog or skip

- by fooyee

am pulling my hair over this :( spent 10 hrs but nothing came out I read this thread http://forum.developers.facebook.com/viewtopic.php?pid=198128 but it didn't help much. I'm running a local dev App Engine server ( localhost:8080 ) iframe app so I have a couple of problems. 1) on safari 4.0.4, the publish story dialog comes up nicely with all images/data/action_links. upon posting a story (or skipping), the dialog goes blank and wouldn't close. 2) I tested the same code on firefox 3.5.8, the dialog comes up with all images/data/action_links, but then the whole thing freezes. Clicking anywhere on the dialog doesn't help at all. If i'm patient enough and click "publish", I have to wait for abt 10 seconds before the dialog says "story is published". then it freezes. (clicking on skip doesn't make a difference). btw, there is no "button clicking effect" : ie: the buttons don't look like they "sink down" upon clicking. I checked the firefox memory using the command "top" on the terminal, it all seems okay, no spike in CPU processes ( i could open other firefox tabs and work on them) My futile attempts at solving the problems... 1) so i thought, hmm could this be because of local dev (localhost) problem? I uploaded the code to the production server, the same thing happens. 2) I tried an older firefox (3.1) and the same problem persisted ( the freezing ) 3) I noticed that i kind of used 2 different FB features ( Connect and XFBML). The Connect Feature I used in the PostStory function. The XFBML feature I used before the tag. So I thought, hmm ... I tried replacing the FB_RequireFeatures["Connect"] feature with FB_RequireFeatures["XFBML"]. nothing changed. I still can't close the story dialog. 4) Is there a possibility that I didn't connect to xd_receiver.htm properly? my xd_receiver.htm is stored in my folder /media/fbconnect in my app.yaml handler: - url: /fbconnect static_dir: media/fbconnect so i thought a connection has to be established with xd_receiver.htm. any way I can test that? here're all the codes: <script type="text/javascript"> //post story function function PostStory() { //init facebook FB_RequireFeatures(["Connect"], function() { FB.Facebook.init('my_app_key', "/fbconnect/xd_receiver.htm"); FB.ensureInit(function() { var message = 'the message'; var attachment = { 'name': 'a simple app to send gifts', 'href': 'http://apps.facebook.com/my_app_name', 'caption': '{*actor*} sent u something', 'description': 'some description', "media": [{ "type": "image", "src": "http://bit.ly/105QYr", "href": "http://bit.ly/105QYr"}] }; //action links can only be seen AFTER the feed is published var action_links = [{ 'text': 'Send him/her a gift back!', 'href': 'http://somelink.com'}]; FB.Connect.streamPublish(message, attachment, action_links, null, "Share the gift with your friends", callback, false, null); }); }); function callback(post_id, exception) { //alert('Wall Post Complete'); } } </script> just before the end of the /body tag, i have this: <script type="text/javascript"> function callFBInit() { FB_RequireFeatures( ["XFBML"], function(){ FB.Facebook.init("my_app_key", "/fbconnect/xd_receiver.htm"); } ); } callFBInit(); btw, my xd_receiver.htm contains: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns=? http://www.w3.org/1999/xhtml? > <head> <title>cross-domain receiver page</title> </head> <body> <script src=?http://static.ak.facebook.com/js/api_lib/v0.4/xdcommreceiver.debug.js? type=? text/javascript? ></script> </body> </html> hope you guys can help out. thx

Read the article

Silverlight 3.0 Custom Cursor in Chart

- by Wonko the Sane

Hello All, I'm probably overlooking something that will be obvious when I see the solution, but for now... I am attempting to use a custom cursor inside the chart area of a Toolkit chart. I have created a ControlTemplate for the chart, and a grid to contain the cursors. I show/hide the cursors, and attempt to move the containing Grid, using various Mouse events. The cursor is being displayed at the correct times, but I cannot get it to move to the correct position. Here is the ControlTemplate (the funky colors are just attempts to confirm what the different pieces of the template pertain to): <dataVisTK:Title Content="{TemplateBinding Title}" Style="{TemplateBinding TitleStyle}"/> <Grid Grid.Row="1">   <chartingPrimitivesTK:EdgePanel x:Name="ChartArea" Background="#EDAEAE" Style="{TemplateBinding ChartAreaStyle}" Grid.Column="0"> <Grid Canvas.ZIndex="-1" Background="#2008AE" Style="{TemplateBinding PlotAreaStyle}"> </Grid> <Border Canvas.ZIndex="1" BorderBrush="#FF250010" BorderThickness="3" /> <Grid x:Name="gridHandCursors" Canvas.ZIndex="5" Width="32" Height="32" Visibility="Collapsed"> <Image x:Name="cursorGrab" Width="32" Source="Resources/grab.png" /> <Image x:Name="cursorGrabbing" Width="32" Source="Resources/grabbing.png" Visibility="Collapsed"/> </Grid> </chartingPrimitivesTK:EdgePanel> </Grid> </Grid> </Border> and here are the mouse events (in particular, the MouseMove): void TimelineChart_Loaded(object sender, RoutedEventArgs e) { chartTimeline.UpdateLayout(); List<FrameworkElement> chartChildren = GetLogicalChildrenBreadthFirst(chartTimeline).ToList(); mChartArea = chartChildren.Where(element => element.Name.Equals("ChartArea")).FirstOrDefault() as Panel; if (mChartArea != null) { grabCursor = chartChildren.Where(element => element.Name.Equals("cursorGrab")).FirstOrDefault() as Image; grabbingCursor = chartChildren.Where(element => element.Name.Equals("cursorGrabbing")).FirstOrDefault() as Image; mGridHandCursors = chartChildren.Where(element => element.Name.Equals("gridHandCursors")).FirstOrDefault() as Grid; mChartArea.Cursor = Cursors.None; mChartArea.MouseMove += new MouseEventHandler(mChartArea_MouseMove); mChartArea.MouseLeftButtonDown += new MouseButtonEventHandler(mChartArea_MouseLeftButtonDown); mChartArea.MouseLeftButtonUp += new MouseButtonEventHandler(mChartArea_MouseLeftButtonUp); if (mGridHandCursors != null) { mChartArea.MouseEnter += (s, e2) => mGridHandCursors.Visibility = Visibility.Visible; mChartArea.MouseLeave += (s, e2) => mGridHandCursors.Visibility = Visibility.Collapsed; } } } void mChartArea_MouseLeftButtonUp(object sender, MouseButtonEventArgs e) { if (grabCursor != null) grabCursor.Visibility = Visibility.Visible; if (grabbingCursor != null) grabbingCursor.Visibility = Visibility.Collapsed; } void mChartArea_MouseLeftButtonDown(object sender, MouseButtonEventArgs e) { if (grabCursor != null) grabCursor.Visibility = Visibility.Collapsed; if (grabbingCursor != null) grabbingCursor.Visibility = Visibility.Visible; } void mChartArea_MouseMove(object sender, MouseEventArgs e) { if (mGridHandCursors != null) { Point pt = e.GetPosition(null); mGridHandCursors.SetValue(Canvas.LeftProperty, pt.X); mGridHandCursors.SetValue(Canvas.TopProperty, pt.Y); } } Any help past this roadblock would be greatly appreciated! Thanks, wTs

Read the article

AT91SAM7X512's SPI peripheral gets disabled on write to SPI_TDR

- by Dor

My AT91SAM7X512's SPI peripheral gets disabled on the X time (X varies) that I write to SPI_TDR. As a result, the processor hangs on the while loop that checks the TDRE flag in SPI_SR. This while loop is located in the function SPI_Write() that belongs to the software package/library provided by ATMEL. The problem occurs arbitrarily - sometimes everything works OK and sometimes it fails on repeated attempts (attemp = downloading the same binary to the MCU and running the program). Configurations are (defined in the order of writing): SPI_MR: MSTR = 1 PS = 0 PCSDEC = 0 PCS = 0111 DLYBCS = 0 SPI_CSR[3]: CPOL = 0 NCPHA = 1 CSAAT = 0 BITS = 0000 SCBR = 20 DLYBS = 0 DLYBCT = 0 SPI_CR: SPIEN = 1 After setting the configurations, the code verifies that the SPI is enabled, by checking the SPIENS flag. I perform a transmission of bytes as follows: const short int dataSize = 5; // Filling array with random data unsigned char data[dataSize] = {0xA5, 0x34, 0x12, 0x00, 0xFF}; short int i = 0; volatile unsigned short dummyRead; SetCS3(); // NPCS3 == PIOA15 while(i-- < dataSize) { mySPI_Write(data[i]); while((AT91C_BASE_SPI0->SPI_SR & AT91C_SPI_TXEMPTY) == 0); dummyRead = SPI_Read(); // SPI_Read() from Atmel's library } ClearCS3(); /**********************************/ void mySPI_Write(unsigned char data) { while ((AT91C_BASE_SPI0->SPI_SR & AT91C_SPI_TXEMPTY) == 0); AT91C_BASE_SPI0->SPI_TDR = data; while ((AT91C_BASE_SPI0->SPI_SR & AT91C_SPI_TDRE) == 0); // <-- This is where // the processor hangs, because that the SPI peripheral is disabled // (SPIENS equals 0), which makes TDRE equal to 0 forever. } Questions: What's causing the SPI peripheral to become disabled on the write to SPI_TDR? Should I un-comment the line in SPI_Write() that reads the SPI_RDR register? Means, the 4th line in the following code: (The 4th line is originally marked as a comment) void SPI_Write(AT91S_SPI *spi, unsigned int npcs, unsigned short data) { // Discard contents of RDR register //volatile unsigned int discard = spi->SPI_RDR; /* Send data */ while ((spi->SPI_SR & AT91C_SPI_TXEMPTY) == 0); spi->SPI_TDR = data | SPI_PCS(npcs); while ((spi->SPI_SR & AT91C_SPI_TDRE) == 0); } Is there something wrong with the code above that transmits 5 bytes of data? Please note: The NPCS line num. 3 is a GPIO line (means, in PIO mode), and is not controlled by the SPI controller. I'm controlling this line by myself in the code, by de/asserting the ChipSelect#3 (NPCS3) pin when needed. The reason that I'm doing so is because that problems occurred while trying to let the SPI controller to control this pin. I didn't reset the SPI peripheral twice, because that the errata tells to reset it twice only if I perform a reset - which I don't do. Quoting the errata: If a software reset (SWRST in the SPI Control Register) is performed, the SPI may not work properly (the clock is enabled before the chip select.) Problem Fix/Workaround The SPI Control Register field, SWRST (Software Reset) needs to be written twice to be cor- rectly set. I noticed that sometimes, if I put a delay before the write to the SPI_TDR register (in SPI_Write()), then the code works perfectly and the communications succeeds. Useful links: AT91SAM7X Series Preliminary.pdf ATMEL software package/library spi.c from Atmel's library spi.h from Atmel's library An example of initializing the SPI and performing a transfer of 5 bytes is highly appreciated and helpful.

Read the article

SSL and mod_rewrite error

- by wnoveno

Hi, I have https on my site. Pages with rewritten URL in my site are inaccessible while direct urls (folders). here's the htaccess ## 2009-12-17 16:52 JGC [START] ## Enable http compression for this site <IfModule mod_deflate.c> SetOutputFilter DEFLATE ## Directive "DeflateCompressionLevel" not allowed in .htaccess, only valid in server config and virtual hosts # DeflateCompressionLevel 9 # file-types indicated will not be compressed SetEnvIfNoCase Request_URI \.(?:gif|jpe?g|png)$ no-gzip dont-vary SetEnvIfNoCase Request_URI \.(?:swf|flv|pdf)$ no-gzip dont-vary SetEnvIfNoCase Request_URI \.(?:exe|t?gz|zip|gz2|sit|rar)$ no-gzip dont-vary <IfModule mod_headers.c> Header append Vary User-Agent </IfModule> </IfModule> ## 2009-12-17 16:52 JGC [END] ## 2010-03-05 16:05 JGC [START] #<IfModule mod_alias.c> #RedirectMatch 301 ^(/)$ /online-casino-poker-register.html #RedirectMatch 301 ^(/en)$ /en/online-casino-poker-register.html #RedirectMatch 301 ^(/en/)$ /en/online-casino-poker-register.html #RedirectMatch 301 ^(/en\.html)$ /en/online-casino-poker-register.html #RedirectMatch 301 ^(/sc)$ /sc/online-casino-poker-register.html #RedirectMatch 301 ^(/sc/)$ /sc/online-casino-poker-register.html #RedirectMatch 301 ^(/sc\.html)$ /sc/online-casino-poker-register.html #RedirectMatch 301 ^(/ch)$ /ch/online-casino-poker-register.html #RedirectMatch 301 ^(/ch/)$ /ch/online-casino-poker-register.html #RedirectMatch 301 ^(/ch\.html)$ /ch/online-casino-poker-register.html #</IfModule> ## 2010-03-05 16:05 JGC [END] ## # @version $Id: htaccess.txt 10492 2008-07-02 06:38:28Z ircmaxell $ # @package Joomla # @copyright Copyright (C) 2005 - 2008 Open Source Matters. All rights reserved. # @license http://www.gnu.org/copyleft/gpl.html GNU/GPL # Joomla! is Free Software ## ##################################################### # READ THIS COMPLETELY IF YOU CHOOSE TO USE THIS FILE # # The line just below this section: 'Options +FollowSymLinks' may cause problems # with some server configurations. It is required for use of mod_rewrite, but may already # be set by your server administrator in a way that dissallows changing it in # your .htaccess file. If using it causes your server to error out, comment it out (add # to # beginning of line), reload your site in your browser and test your sef url's. If they work, # it has been set by your server administrator and you do not need it set here. # ##################################################### ## Can be commented out if causes errors, see notes above. Options +FollowSymLinks # # mod_rewrite in use RewriteEngine On #RewriteLog "/var/www/html/dafa888/rewrite.log" #RewriteLogLevel 3 RewriteCond %{HTTP_COOKIE} !jfcookie\[lang\] [NC] RewriteCond %{HTTP:Accept-Language} ^zh-cn [NC] RewriteRule ^$ /sc/ [L,R=301] RewriteCond %{HTTP_COOKIE} !jfcookie\[lang\] [NC] RewriteCond %{HTTP:Accept-Language} ^zh-tw [NC] RewriteRule ^$ /ch/ [L,R=301] #RewriteCond %{HTTP_COOKIE} !jfcookie[lang] [NC] #RewriteCond %{HTTP_COOKIE} jfcookie\[lang\] [NC] #RewriteCond %{HTTP_COOKIE} jfcookie\[lang\]=([^;]+) [NC] #RewriteRule ^(.*)$ /%1/$1 [NC,QSA] ########## Begin - Rewrite rules to block out some common exploits ## If you experience problems on your site block out the operations listed below ## This attempts to block the most common type of exploit `attempts` to Joomla! # # Block out any script trying to set a mosConfig value through the URL RewriteCond %{QUERY_STRING} mosConfig_[a-zA-Z_]{1,21}(=|\%3D) [OR] # Block out any script trying to base64_encode crap to send via URL RewriteCond %{QUERY_STRING} base64_encode.*$.*$ [OR] # Block out any script that includes a <script> tag in URL RewriteCond %{QUERY_STRING} (\<|%3C).*script.*(\>|%3E) [NC,OR] # Block out any script trying to set a PHP GLOBALS variable via URL RewriteCond %{QUERY_STRING} GLOBALS(=|\[|\%[0-9A-Z]{0,2}) [OR] # Block out any script trying to modify a _REQUEST variable via URL RewriteCond %{QUERY_STRING} _REQUEST(=|\[|\%[0-9A-Z]{0,2}) # Send all blocked request to homepage with 403 Forbidden error! RewriteRule ^(.*)$ index.php [F,L] # ########## End - Rewrite rules to block out some common exploits # Uncomment following line if your webserver's URL # is not directly related to physical file paths. # Update Your Joomla! Directory (just / for root) RewriteBase / #RewriteCond %{HTTP_HOST} ^(.*)$ [NC] #RewriteRule ^(.*)$ http://www.%1/$1 [R=301] ########## Begin - Joomla! core SEF Section # RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/index.php RewriteCond %{REQUEST_URI} (/|\.php|\.html|\.htm|\.feed|\.pdf|\.raw|/[^.]*)$ [NC] RewriteRule (.*) index.php RewriteRule .* - [E=HTTP_AUTHORIZATION:%{HTTP:Authorization},L] # ########## End - Joomla! core SEF Section

Read the article

Getting Custom NSCell with NSButtonCell instance to handle mouse click/mouse events

- by sidha

OK I'm really stumped on this one. I want to make a checkbox with a NSTextFieldCell combined together. It's important that the checkbox goes ON if the mouse hits the box, NOT the text. I've accomplished this, more or less, but the issue is receiving the mouse event because I click one checkbox in a row, but ALL of them turn to NSOnState. I will show what I've done and my various failed attempts in order to get this to work. So this is how I've done it so far: header: @interface MyCheckboxCellToo : NSTextFieldCell { NSButtonCell *_checkboxCell; } implementation: - (NSUInteger)hitTestForEvent:(NSEvent *)event inRect:(NSRect)cellFrame ofView:(NSView *)controlView { NSPoint point = [controlView convertPoint:[event locationInWindow] fromView:nil]; NSLog(@"%@", NSStringFromPoint(point)); NSRect checkFrame; NSDivideRect(cellFrame, &checkFrame, &cellFrame, cellFrame.size.height/*3 + [[_checkboxCell image] size].width*/, NSMinXEdge); if (NSMouseInRect(point, checkFrame, [controlView isFlipped])) { // the checkbox, or the small region around it, was hit. so let's flip the state NSCellStateValue checkState = ([_checkboxCell state] == NSOnState) ? NSOffState:NSOnState; [self setState:checkState]; [_checkboxCell setState:checkState]; [controlView setNeedsDisplay:YES]; return NSCellHitTrackableArea; } return [super hitTestForEvent:event inRect:cellFrame ofView:controlView]; } I know I probably shouldn't be doing: [self setState:checkState]; [_checkboxCell setState:checkState]; [controlView setNeedsDisplay:YES]; in there... because the result is that EVERY checkbox in every goes to NSOnState. Is this because cells are re-used? How come the ImageAndTextCell can have different images in the same tableview? How do I handle the mouse event? I have tried: - (BOOL)trackMouse:(NSEvent *)theEvent inRect:(NSRect)cellFrame ofView:(NSView *)controlView untilMouseUp:(BOOL)untilMouseUp { NSLog(@"%s %@", _cmd, theEvent); return [_checkboxCell trackMouse:theEvent inRect:cellFrame ofView:controlView untilMouseUp:untilMouseUp]; // return YES; // return [super trackMouse:theEvent inRect:cellFrame ofView:controlView untilMouseUp:untilMouseUp]; } - (BOOL)startTrackingAt:(NSPoint)startPoint inView:(NSView *)controlView { NSLog(@"%s %@", _cmd, NSStringFromPoint(startPoint)); return [super startTrackingAt:startPoint inView:controlView]; } - (BOOL)continueTracking:(NSPoint)lastPoint at:(NSPoint)currentPoint inView:(NSView *)controlView { NSLog(@"%s %@", _cmd, NSStringFromPoint(currentPoint)); return [super continueTracking:lastPoint at:currentPoint inView:controlView]; } - (void)stopTracking:(NSPoint)lastPoint at:(NSPoint)stopPoint inView:(NSView *)controlView mouseIsUp:(BOOL)flag { NSLog(@"%s %d %@", _cmd, flag, NSStringFromPoint(stopPoint)); } trackMouse: ... DOES gets called but startTrackingAt:..., continueTracking:..., and stopTracking:.... DO NOT get called when I click on the checkbox "hit area" in trackMouse:... I have tried return [_checkboxCell trackMouse:theEvent inRect:cellFrame ofView:controlView untilMouseUp:untilMouseUp]; and return [super trackMouse:theEvent inRect:cellFrame ofView:controlView untilMouseUp:untilMouseUp]; and neither seems to result in the mouse event being handled by the checkbox. How do I get that single checkbox to go NSOnState? I know I'm pretty close but after a lot of doc reading and google searching I haven't been successful at solving this. suggestions and comments welcome.. OK here is a bit more to show creation and destruction of the object.. - (id)init { if ((self = [super init])) { _checkboxCell = [[NSButtonCell alloc] init]; [_checkboxCell setButtonType:NSSwitchButton]; [_checkboxCell setTitle:@""]; [_checkboxCell setTarget:self]; [_checkboxCell setImagePosition:NSImageLeft]; [_checkboxCell setControlSize:NSRegularControlSize]; } return self; } - copyWithZone:(NSZone *)zone { MyCheckboxCellToo *cell = (MyCheckboxCellToo *)[super copyWithZone:zone]; cell->_checkboxCell = [_checkboxCell copyWithZone:zone]; return cell; } - (void)dealloc { [_checkboxCell release]; [super dealloc]; }

Read the article

NSURLConnection not "firing" until UITableView scrolls..

- by Simon

Hi, I've got a UITableView that loads an image asynchronously and places it in the UITableViewCell once it's loaded (I'm using almost the exact same code as in the "LazyTableImages" tutorial). This works fine for all images when I scroll the table, but it's not loading the images that are first in the view. The code is definitely working fine as the class that actually sends the NSURLConnection request is being called correctly (I added an NSLog and it reached the console). The NSURLConnection is just not calling the delegate methods (didReceiveData, connectionDidFinishLoading, etc). Here's my code: HomeController.m - (UITableViewCell *)tableView:(UITableView *)tableView cellForRowAtIndexPath:(NSIndexPath *)indexPath { static NSString *CellIdentifier = @"Cell"; UITableViewCell *cell = [tableView dequeueReusableCellWithIdentifier:CellIdentifier]; if (cell == nil) { cell = [[[UITableViewCell alloc] initWithStyle:UITableViewCellStyleDefault reuseIdentifier:CellIdentifier] autorelease]; NSArray *feed = [feeds objectAtIndex: indexPath.row]; /** * Name of person */ [...] /** * Feed entry */ [...] /** * Misc work */ [...] } FeedRecord *feedRecord = [self.entries objectAtIndex:indexPath.row]; if( !feedRecord.image ) { if (self.table.dragging == NO && self.table.decelerating == NO) { [self startIconDownload:feedRecord forIndexPath:indexPath]; } cell.imageView.image = [UIImage imageNamed:@"Placeholder.png"]; } return cell; } - (void)startIconDownload:(FeedRecord *)feedRecord forIndexPath:(NSIndexPath *)indexPath { IconDownloader *iconDownloader = [imageDownloadsInProgress objectForKey:indexPath]; if (iconDownloader == nil) { iconDownloader = [[IconDownloader alloc] init]; iconDownloader.feedRecord = feedRecord; iconDownloader.indexPathInTableView = indexPath; iconDownloader.delegate = self; [imageDownloadsInProgress setObject:iconDownloader forKey:indexPath]; [iconDownloader startDownload]; [iconDownloader release]; } } IconDownload.m #import "IconDownloader.h" #import "FeedRecord.h" #define kAppIconHeight 48 @implementation IconDownloader @synthesize feedRecord; @synthesize indexPathInTableView; @synthesize delegate; @synthesize activeDownload; @synthesize imageConnection; #pragma mark - (void)dealloc { [feedRecord release]; [indexPathInTableView release]; [activeDownload release]; [imageConnection cancel]; [imageConnection release]; [super dealloc]; } - (void)startDownload { NSLog(@"%@ %@",@"Started downloading", feedRecord.profilePicture); // this shows in log self.activeDownload = [NSMutableData data]; // alloc+init and start an NSURLConnection; release on completion/failure NSURLConnection *conn = [[NSURLConnection alloc] initWithRequest: [NSURLRequest requestWithURL: [NSURL URLWithString:feedRecord.profilePicture]] delegate:self]; self.imageConnection = conn; NSLog(@"%@",conn); // this shows in log [conn release]; } - (void)cancelDownload { [self.imageConnection cancel]; self.imageConnection = nil; self.activeDownload = nil; } #pragma mark - #pragma mark Download support (NSURLConnectionDelegate) - (void)connection:(NSURLConnection *)connection didReceiveData:(NSData *)data { NSLog(@"%@ %@",@"Got data for", feedRecord.profilePicture); [self.activeDownload appendData:data]; } - (void)connection:(NSURLConnection *)connection didFailWithError:(NSError *)error { NSLog(@"%@",@"Fail!"); // Clear the activeDownload property to allow later attempts self.activeDownload = nil; // Release the connection now that it's finished self.imageConnection = nil; } - (void)connectionDidFinishLoading:(NSURLConnection *)connection { NSLog(@"%@ %@",@"Done", feedRecord.profilePicture); // Set appIcon and clear temporary data/image UIImage *image = [[UIImage alloc] initWithData:self.activeDownload]; self.feedRecord.image = image; self.activeDownload = nil; [image release]; // Release the connection now that it's finished self.imageConnection = nil; NSLog(@"%@ %@",@"Our delegate is",delegate); // call our delegate and tell it that our icon is ready for display [delegate feedImageDidLoad:self.indexPathInTableView]; } @end Has anyone else experienced anything like this or can identify an issue with my code? Thanks!

Read the article

How can I reset addAttributeToFilter in Magento searches

- by Bobby

I'm having problems getting the addAttributeToFilter function within a loop to behave in Magento. I have test data in my store to support searches for all of the following data; $attributeSelections=array( array('size' => 44, 'color' => 67, 'manufacturer' => 17), array('size' => 43, 'color' => 69, 'manufacturer' => 17), array('size' => 42, 'color' => 70, 'manufacturer' => 17)); And my code to search through these combinations; foreach ($attributeSelections as $selection) { $searcher = Mage::getSingleton('catalogsearch/advanced')->getProductCollection(); foreach ($selection as $k => $v) { $searcher->addAttributeToFilter("$k", array('eq' => "$v")); echo "$k: $v<br />"; } $result=$searcher->getData(); print_r($result); } This loop gives the following results (slightly sanitised for veiwing pleasure); size: 44 color: 67 manufacturer: 17 Array ( [0] => Array ( [entity_id] => 2965 [entity_type_id] => 4 [attribute_set_id] => 28 [type_id] => simple [sku] => 1006-0001 [size] => 44 [color] => 67 [manufacturer] => 17 ) ) size: 43 color: 69 manufacturer: 17 Array ( [0] => Array ( [entity_id] => 2965 [entity_type_id] => 4 [attribute_set_id] => 28 [type_id] => simple [sku] => 1006-0001 [size] => 44 [color] => 67 [manufacturer] => 17 ) ) size: 42 color: 70 manufacturer: 17 Array ( [0] => Array ( [entity_id] => 2965 [entity_type_id] => 4 [attribute_set_id] => 28 [type_id] => simple [sku] => 1006-0001 [size] => 44 [color] => 67 [manufacturer] => 17 ) ) So my loop is function and generating the search. However, the values fed into addAttributeToFilter on the first itteration of the loop seem to remain stored for each search. I've tried clearing my search object, for example, unset($searcher) and unset($result). I've also tried magento functions such as getNewEmptyItem(), resetData(), distinct() and clear() but none have the desired effect. Basically what I am trying to do is check for duplicate products before my script attempts to programatically create a product with these attribute combinations. The array of attribute selections may be of varying sizes hence the need for a loop. I would be very appreiciative if anyone might be able to shed some light on my problem.

Read the article

TripleDES in Perl/PHP/ColdFusion

- by Seidr

Recently a problem arose regarding hooking up an API with a payment processor who were requesting a string to be encrypted to be used as a token, using the TripleDES standard. Our Applications run using ColdFusion, which has an Encrypt tag - that supports TripleDES - however the result we were getting back was not what the payment processor expected. First of all, here is the resulting token the payment processor were expecting. AYOF+kRtg239Mnyc8QIarw== And below is the snippet of ColdFusion we were using, and the resulting string.  <cfset theKey="123412341234123412341234"> <cfset theString = "username=test123"> <cfset strEncodedEnc = Encrypt(theString, theKey, "DESEDE", "Base64")>  As you can see, this was not returning the string we were hoping for. Seeking a solution, we ditched ColdFusion for this process and attempted to reproduce the token in PHP. Now I'm aware that various languages implement encryption in different ways - for example in the past managing encryption between a C# application and PHP back-end, I've had to play about with padding in order to get the two to talk, but my experience has been that PHP generally behaves when it comes to encryption standards. Anyway, on to the PHP source we tried, and the resulting string. /* PHP Circus (here be Elephants) */ $theKey="123412341234123412341234"; $theString="username=test123"; $strEncodedEnc=base64_encode(mcrypt_ecb (MCRYPT_3DES, $theKey, $theString, MCRYPT_ENCRYPT)); /* resulting string(strEncodedEnc): sfiSu4mVggia8Ysw98x0uw== */ As you can plainly see, we've got another string that differs from both the string expected by the payment processor AND the one produced by ColdFusion. Cue head-against-wall integration techniques. After many to-and-fro communications with the payment processor (lots and lots of reps stating 'we can't help with coding issues, you must be doing it incorrectly, read the manual') we were finally escalated to someone with more than a couple of brain-cells to rub together, who was able to step back and actually look at and diagnose the issue. He agreed, our CF and PHP attempts were not resulting in the correct string. After a quick search, he also agreed that it was not neccesarily our source, but rather how the two languages implemented their vision of the TripleDES standard. Coming into the office this morning, we were met by an email with a snippet of source code, in Perl. This is was the code they were directly using on their end to produce the expected token. #!/usr/bin/perl # Perl Crypt Calamity (here be...something) use strict; use CGI; use MIME::Base64; use Crypt::TripleDES; my $cgi = CGI->new(); my $param = $cgi->Vars(); $param->{key} = "123412341234123412341234"; $param->{string} = "username=test123"; my $des = Crypt::TripleDES->new(); my $enc = $des->encrypt3($param->{string}, $param->{key}); $enc = encode_base64($enc); $enc =~ s/\n//gs; # resulting string (enc): AYOF+kRtg239Mnyc8QIarw== So, there we have it. Three languages, three implementations of what they quote in the documentation as TripleDES Standard Encryption, and three totally different resulting strings. My question is, from your experience of these three languages and their implementations of the TripleDES algorithm, have you been able to get any two of them to give the same response, and if so what tweaks to the code did you have to make in order to come to the result? I understand this is a very drawn out question, but I wanted to give clear and precise setting for each stage of testing that we had to perform. I'll also be performing some more investigatory work on this subject later, and will post any findings that I come up with to this question, so that others may avoid this headache.

Read the article

Java Synchronized List Deadlock

- by portoalet

From Effective Java 2nd edition item 67 page 266-268: The background thread calls s.removeObserver, which attempts to lock observers, but it can’t acquire the lock, because the main thread already has the lock. All the while, the main thread is waiting for the background thread to finish removing the observer, which explains the deadlock. I am trying to find out which threads deadlock in the main method by using ThreadMXBean (http://stackoverflow.com/questions/1102359/programmatic-deadlock-detection-in-java) , but why does it not return the deadlocked threads? I used a new Thread to run the ThreadMXBean detection. public class ObservableSet<E> extends ForwardingSet<E> { public ObservableSet(Set<E> set) { super(set); } private final List<SetObserver<E>> observers = new ArrayList<SetObserver<E>>(); public void addObserver(SetObserver<E> observer) { synchronized(observers) { observers.add(observer); } } public boolean removeObserver(SetObserver<E> observer) { synchronized(observers) { return observers.remove(observer); } } private void notifyElementAdded(E element) { synchronized(observers) { for (SetObserver<E> observer : observers) observer.added(this, element); } } @Override public boolean add(E element) { boolean added = super.add(element); if (added) notifyElementAdded(element); return added; } @Override public boolean addAll(Collection<? extends E> c) { boolean result = false; for (E element : c) result|=add(element); //callsnotifyElementAdded return result; } public static void main(String[] args) { ObservableSet<Integer> set = new ObservableSet<Integer>(new HashSet<Integer>()); final ThreadMXBean threadMxBean = ManagementFactory.getThreadMXBean(); Thread t = new Thread(new Runnable() { @Override public void run() { while( true ) { long [] threadIds = threadMxBean.findDeadlockedThreads(); if( threadIds != null) { ThreadInfo[] infos = threadMxBean.getThreadInfo(threadIds); for( ThreadInfo threadInfo : infos) { StackTraceElement[] stacks = threadInfo.getStackTrace(); for( StackTraceElement stack : stacks ) { System.out.println(stack.toString()); } } } try { System.out.println("Sleeping.."); TimeUnit.MILLISECONDS.sleep(1000); } catch (InterruptedException e) { // TODO Auto-generated catch block e.printStackTrace(); } } } }); t.start(); set.addObserver(new SetObserver<Integer>() { public void added(ObservableSet<Integer> s, Integer e) { ExecutorService executor = Executors.newSingleThreadExecutor(); final SetObserver<Integer> observer = this; try { executor.submit(new Runnable() { public void run() { s.removeObserver(observer); } }).get(); } catch (ExecutionException ex) { throw new AssertionError(ex.getCause()); } catch (InterruptedException ex) { throw new AssertionError(ex.getCause()); } finally { executor.shutdown(); } } }); for (int i = 0; i < 100; i++) set.add(i); } } public interface SetObserver<E> { // Invoked when an element is added to the observable set void added(ObservableSet<E> set, E element); } // ForwardingSet<E> simply wraps another Set and forwards all operations to it.

Read the article

Need Help Setting Transparent Image to Clipboard

- by AMissico

I need help setting a transparent image to the clipboard. I keep getting "handle is invalid". Following is the specific code with the complete working project at ftp://missico.net/ImageVisualizer.zip. This is an image Debug Visualizer class library, but I made to run as executable for testing. (Note that window is a toolbox window and show in taskbar is set to false.) I was tired of having to perform a screen capture on the toolbox window, open with an image editor, and then deleting the background added due to the screen capture. So I thought I would quickly put the transparent image onto the clipboard. Well, the problem is...no transparency support for Clipboard.SetImage. Google to the rescue...not quite. This is what I have so far pulled from a number of sources. See the code for the main reference. My problem is the "invalid handle" when using CF_DIBV5. I imagine the problem is related to BITMAPV5HEADER and CreateDIBitmap. Any help from you GDI/GDI+ Wizards would be greatly appreciated. public static void SetClipboardData(Bitmap bitmap, IntPtr hDC) { const uint SRCCOPY = 0x00CC0020; const int CF_DIBV5 = 17; const int CF_BITMAP = 2; //'reference //'http://social.msdn.microsoft.com/Forums/en-US/winforms/thread/816a35f6-9530-442b-9647-e856602cc0e2 IntPtr memDC = CreateCompatibleDC(hDC); IntPtr memBM = CreateCompatibleBitmap(hDC, bitmap.Width, bitmap.Height); SelectObject(memDC, memBM); using (Graphics g = Graphics.FromImage(bitmap)) { IntPtr hBitmapDC = g.GetHdc(); IntPtr hBitmap = bitmap.GetHbitmap(); SelectObject(hBitmapDC, hBitmap); BitBlt(memDC, 0, 0, bitmap.Width, bitmap.Height, hBitmapDC, 0, 0, SRCCOPY); if (!OpenClipboard(IntPtr.Zero)) { throw new System.Runtime.InteropServices.ExternalException("Could not open Clipboard", new Win32Exception()); } if (!EmptyClipboard()) { throw new System.Runtime.InteropServices.ExternalException("Unable to empty Clipboard", new Win32Exception()); } //IntPtr hClipboard = SetClipboardData(CF_BITMAP, memBM); //works but image is not transparent //all my attempts result in SetClipboardData returning hClipboard = IntPtr.Zero IntPtr hClipboard = SetClipboardData(CF_DIBV5, memBM); //because if (hClipboard == IntPtr.Zero) { // InnerException: System.ComponentModel.Win32Exception // Message="The handle is invalid" // ErrorCode=-2147467259 // NativeErrorCode=6 // InnerException: throw new System.Runtime.InteropServices.ExternalException("Could not put data on Clipboard", new Win32Exception()); } if (!CloseClipboard()) { throw new System.Runtime.InteropServices.ExternalException("Could not close Clipboard", new Win32Exception()); } g.ReleaseHdc(hBitmapDC); } } private void __copyMenuItem_Click(object sender, EventArgs e) { //'Applications that I have verified can paste the clipboard custom data format PNG are: //' Word 2003 //' Excel 2003 using (Graphics g = __pictureBox.CreateGraphics()) { IntPtr hDC = g.GetHdc(); MemoryStream ms = new MemoryStream(); __pictureBox.Image.Save(ms, ImageFormat.Png); ms.Seek(0, SeekOrigin.Begin); Image imag = Image.FromStream(ms); // Derive BitMap object using Image instance, so that you can avoid the issue //"a graphics object cannot be created from an image that has an indexed pixel format" Bitmap img = new Bitmap(new Bitmap(imag)); SetClipboardData(img, hDC); g.ReleaseHdc(); } }

Read the article

Sending emails in web applications

- by Denise

Hi everyone, I'm looking for some opinions here, I'm building a web application which has the fairly standard functionality of: Register for an account by filling out a form and submitting it. Receive an email with a confirmation code link Click the link to confirm the new account and log in When you send emails from your web application, it's often (usually) the case that there will be some change to the persistence layer. For example: A new user registers for an account on your site - the new user is created in the database and an email is sent to them with a confirmation link A user assigns a bug or issue to someone else - the issue is updated and email notifications are sent. How you send these emails can be critical to the success of your application. How you send them depends on how important it is that the intended recipient receives the email. We'll look at the following four strategies in relation to the case where the mail server is down, using example 1. TRANSACTIONAL & SYNCHRONOUS The sending of the email fails and the user is shown an error message saying that their account could not be created. The application will appear to be slow and unresponsive as the application waits for the connection timeout. The account is not created in the database because the transaction is rolled back. TRANSACTIONAL & ASYNCHRONOUS The transactional definition here refers to sending the email to a JMS queue or saving it in a database table for another background process to pick up and send. The user account is created in the database, the email is sent to a JMS queue for processing later. The transaction is successful and committed. The user is shown a message saying that their account was created and to check their email for a confirmation link. It's possible in this case that the email is never sent due to some other error, however the user is told that the email has been sent to them. There may be some delay in getting the email sent to the user if application support has to be called in to diagnose the email problem. NON-TRANSACTIONAL & SYNCHRONOUS The user is created in the database, but the application gets a timeout error when it tries to send the email with the confirmation link. The user is shown an error message saying that there was an error. The application is slow and unresponsive as it waits for the connection timeout When the mail server comes back to life and the user tries to register again, they are told their account already exists but has not been confirmed and are given the option of having the email re-sent to them. NON-TRANSACTIONAL & ASYNCHRONOUS The only difference between this and transactional & asynchronous is that if there is an error sending the email to the JMS queue or saving it in the database, the user account is still created but the email is never sent until the user attempts to register again. What I'd like to know is what have other people done here? Can you recommend any other solutions other than the 4 I've mentioned above? What's a reasonable way of approaching this problem? I don't want to over-engineer a system that's dealing with the (hopefully) rare situation where my mail server goes down! The simplest thing to do is to code it synchronously, but are there any other pitfalls to this approach? I guess I'm wondering if there's a best practice, I couldn't find much out there by googling.

Read the article

Fatal error on a non-object

- by Chris Leah

Hey, so I have created a function to check the DB for unique entries, but when I call the function it doesn't seem to work and gives me a fatal error any ideas ? Thanks :) //Check for unique entries function checkUnique($table, $field, $compared) { $query = $mysqli->query('SELECT '.$mysqli->real_escape_string($field).' FROM '.$mysqli->real_escape_string($table).' WHERE "'.$mysqli->real_escape_string($field).'" = "'.$mysqli->real_escape_string($compared).'"'); if(!$query){ return TRUE; } else { return FALSE; } } The page calling it..... //Start session session_start(); //Check if the session is already set, if so re-direct to the game if(isset($_SESSION['id'], $_SESSION['logged_in'])){ Header('Location: ../main/index.php'); }; //Require database connection require_once('../global/includes/db.php'); require_once('../global/functions/functions.php'); //Check if the form has been submitted if (isset($_POST['signup'])){ //Validate input if (!empty($_POST['username']) && !empty($_POST['password']) && $_POST['password']==$_POST['password_confirm'] && !empty($_POST['email']) && validateEmail($_POST['email']) == TRUE && checkUnique('users', 'email', $_POST['email']) == TRUE && checkUnique('users', 'username', $_POST['username']) == TRUE) { //Insert user to the database $insert_user = $mysqli->query('INSERT INTO (`username, `password`, `email`, `verification_key`) VALUES ("'.$mysqli->real_escape_string($_POST['username']).'", "'.$mysqli-real_escape_string(md5($_POST['password'])).'", "'.$mysqli->real_escape_string($_POST['email']).'", "'.randomString('alnum', 32). '"') or die($mysqli->error()); //Get user information $getUser = $mysqli->query('SELECT id, username, email, verification_key FROM users WHERE username = "'.$mysqli->real_escape_string($_POST['username']).'"' or die($mysqli->error())); //Check if the $getUser returns true if ($getUser->num_rows == 1) { //Fetch associated fields to this user $row = $getUser->fetch_assoc(); //Set mail() variables $headers = 'From: [email protected]'."\r\n". 'Reply-To: [email protected]'."\r\n". 'X-Mailer: PHP/'.phpversion(); $subject = 'Activate your account (Music Battles.net)'; //Set verification email message $message = 'Dear '.$row['username'].', I would like to welcome you to Music Battles. Although in order to enjoy the gmae you must first activate your account. \n\n Click the following link: http://www.musicbattles.net/home/confirm.php?id='.$row['id'].'key='.$row['verification_key'].'\n Thanks for signing up, enjoy the game! \n Music Battles Team'; //Attempts to send the email if (mail($row['email'], $subject, $message, $headers)) { $msg = '<p class="success">Accound has been created, please go activate it from your email.</p>'; } else { $error = '<p class="error">The account was created but your email was not sent.</p>'; } } else { $error = '<p class="error">Your account was not created.</p>'; } } else { $error = '<p class="error">One or more fields contain non or invalid data.</p>'; } } Erorr.... Fatal error: Call to a member function query() on a non-object in /home/mbattles/public_html/global/functions/functions.php on line 5

Read the article

Cannot Logout of Facebook with Facebook C# SDK

- by Ryan Smyth

I think I've read just about everything out there on the topic of logging out of Facebook inside of a Desktop application. Nothing so far works. Specifically, I would like to log the user out so that they can switch identities, e.g. People sharing a computer at home could then use the software with their own Facebook accounts, but with no chance to switch accounts, it's quite messy. (Have not yet tested switching Windows users accounts as that is simply far too much to ask of the end user and should not be necessary.) Now, I should say that I have set the application to use these permissions: string[] permissions = new string[] { "user_photos", "publish_stream", "offline_access" }; So, "offline_access" is included there. I do not know if this does/should affect logging out or not. Again, my purpose for logging out is merely to switch users. (If there's a better approach, please let me know.) The purported solutions seem to be: Use the JavaScript SDK (FB.logout()) Use "m.facebook.com" instead Create your own URL (and possibly use m.facebook.com) Create your own URL and use the session variable (in ASP.NET) The first is kind of silly. Why resort to JavaScript when you're using C#? It's kind of a step backwards and has a lot of additional overhead in a desktop application. (I have not tried this as it's simply disgustingly messy to do this in a desktop application.) If anyone can confirm that this is the only working method, please do so. I'm desperately trying to avoid it. The second doesn't work. Perhaps it worked in the past, but my umpteen attempts to get it to work have all failed. The third doesn't work. I've tried umpteen dozen variations with zero success. The last option there doesn't work for a desktop application because it's not ASP.NET and you don't have a session variable to work with. The Facebook C# SDK logout also no longer works. i.e. public FacebookLoginDialog(string appId, string[] extendedPermissions, bool logout) { IDictionary<string, object> loginParameters = new Dictionary<string, object> { { "response_type", "token" }, { "display", "popup" } }; _navigateUri = FacebookOAuthClient.GetLoginUrl(appId, null, extendedPermissions, logout, loginParameters); InitializeComponent(); } I remember it working in the past, but it no longer works now. (Which truly puzzles me...) It instead now directs the user to the Facebook mobile page, where the user must manually logout. Now, I could do browser automation to automatically click the logout link for the user, however, this is prone to breaking if Facebook updates the mobile UI. It is also messy, and possibly a worse solution than trying to use the JavaScript SDK FB.logout() method (though not by much). I have searched for some kind of documentation, however, I cannot find anything in the Facebook developer documentation that illustrates how to logout an application. Has anyone solved this problem, or seen any documentation that can be ported to work with the Facebook C# SDK? I am certainly open to using a WebClient or HttpClient/Response if anyone can point to some documentation that could work with it. I simply have not been able to find any low-level documentation that shows how this approach could work. Thank you in advance for any advice, pointers, or links.

Read the article

Keyboard for programming

- by exhuma

This may seem a bit a tangential topic. It's not directly related to actual code, but is important for our line of work nevertheless. Over the years, I've switched keyboards a few times. All of them had slightly different key layouts. And I'm not talking about the language/locale layout, but the physical layout! Why not the locale layout? Well, quite frankly, that's easy to change via software. I personally have a German keyboard but have it set to the UK layout. Why? It's quite hard to find different layouts in the shops where I live. Even ordering is not always easy in the shops. So that leaves me with Internet shops. But I prefer to "test" my keyboards before buying. The most notable changes are: Mangled "Home Key Block" I've seen this first on a Logitech keyboard, but it may have originated elsewhere. Shape of the "Enter" key I've seen three different cases so far: Two lines high, wider at the top Two lines high, wider at the bottom One line high Shape of the Backspace button I've seen two types so far: One "character" wide Two "characters" wide OS Keys For Macs, you have the Option and Command buttons, for Windows you have the Windows and Context Menu buttons. Cherry even produced a Linux keyboard once (unfortunately I cannot find many details except news results). I assume a dedicated Linux keyboard would sport a Compose key and had the SysRq always labelled as well (note that some standard layouts do this already). Obviously... .. all these differences entail that some keys have to be moved around the board a lot. Which means, if you are used to one and have to work on another one, you happen to hit the wrong keys quite often. As it happens, this is much more annoying for programmers as it is for people who write texts. Mainly because the keys which are moved around are special character keys, often used in programming. Often these hardware layouts depend also indirectly on where you buy the keyboards. Honestly, I haven't seen a keyboard with a one-line "Enter" key in Germany, nor Luxembourg. I may just have missed it but that's how it looks to me at least. A survey I've seen some attempts at surveys in the style "which keyboard is best for programming". But they all - in my opinion - are not using comparable sets. So I was wondering if it was possible to concoct a survey taking the above criteria into account. But ignoring key dimensions that one would be a bit overkill I guess ;) From what I can see there are the following types of physical layout: Backspace: 2-characters wide Enter: 2-Lines, wider top Backspace: 2-characters wide Enter: 1-Line Backspace: 1-character wide Enter: 2-Lines, wider bottom Then there are the other possible permutations (home-key block, os-keys), which in total makes for quite a large list of categories. Now, I wonder... Would anyone be interested in such a survey? I personally would. Because I am looking for the perfect fit for me. If yes, then I could really use the help of anyone here to propose some models to include in the survey. Once I have some models for each category (I'd say at least 3 per category) I could go ahead and write up a survey, put it on-line and let the it collect data for a while. What do you think?

Read the article

How do you stop scripters from slamming your website hundreds of times a second?

- by davebug

[update] I've accepted an answer, as lc deserves the bounty due to the well thought-out answer, but sadly, I believe we're stuck with our original worst case scenario: CAPTCHA everyone on purchase attempts of the crap. Short explanation: caching / web farms make it impossible for us to actually track hits, and any workaround (sending a non-cached web-beacon, writing to a unified table, etc.) slows the site down worse than the bots would. There is likely some pricey bit of hardware from Cisco or the like that can help at a high level, but it's hard to justify the cost if CAPTCHAing everyone is an alternative. I'll attempt to do a more full explanation in here later, as well as cleaning this up for future searchers (though others are welcome to try, as it's community wiki). I've added bounty to this question and attempted to explain why the current answers don't fit our needs. First, though, thanks to all of you who have thought about this, it's amazing to have this collective intelligence to help work through seemingly impossible problems. I'll be a little more clear than I was before: This is about the bag o' crap sales on woot.com. I'm the president of Woot Workshop, the subsidiary of Woot that does the design, writes the product descriptions, podcasts, blog posts, and moderates the forums. I work in the css/html world and am only barely familiar with the rest of the developer world. I work closely with the developers and have talked through all of the answers here (and many other ideas we've had). Usability of the site is a massive part of my job, and making the site exciting and fun is most of the rest of it. That's where the three goals below derive. CAPTCHA harms usability, and bots steal the fun and excitement out of our crap sales. To set up the scenario a little more, bots are slamming our front page tens of times a second screenscraping (and/or scanning our rss) for the Random Crap sale. The moment they see that, it triggers a second stage of the program that logs in, clicks I want One, fills out the form, and buys the crap. In current (2/6/2009) order of votes: lc: On stackoverflow and other sites that use this method, they're almost always dealing with authenticated (logged in) users, because the task being attempted requires that. On Woot, anonymous (non-logged) users can view our home page. In other words, the slamming bots can be non-authenticated (and essentially non-trackable except by IP address). So we're back to scanning for IPs, which a) is fairly useless in this age of cloud networking and spambot zombies and b) catches too many innocents given the number of businesses that come from one IP address (not to mention the issues with non-static IP ISPs and potential performance hits to trying to track this). Oh, and having people call us would be the worst possible scenario. Can we have them call you? BradC Ned Batchelder's methods look pretty cool, but they're pretty firmly designed to defeat bots built for a network of sites. Our problem is bots are built specifically to defeat our site. Some of these methods could likely work for a short time until the scripters evolved their bots to ignore the honeypot, screenscrape for nearby label names instead of form ids, and use a javascript-capable browser control. lc again "Unless, of course, the hype is part of you

Read the article

RegEx to ignore / skip everything in html tags

- by Scott Sumpter

Looking for a way to combine two Regular Expressions. One to catch the urls and the other to ensure is skips text within html tags. See sample text below functions. Need to pass a block of news text and format text by wrapping urls and email addresses in html tags so users don't have to. The below code works great until there are already html tags within the text. In that case it doubles the html tags. There are plenty of examples to strip html, but I want to just ignore it since the url is already linkified. Also - if there is an easier was to accomplish this, with or without Regex, please let me know. none of my attempts to combine Regexs have worked. coding in ASP.NET VB but will take any workable example/direction. Thanks! ===== Functions ============= Public Shared Function InsertHyperlinks(ByVal inText As String) As String Dim strBuf As String Dim objMatches As Object Dim iStart, iEnd As Integer strBuf = "" iStart = 1 iEnd = 1 Dim strRegUrlEmail As String = "\b(www|http|\S+@)\S+\b" 'RegEx to find urls and email addresses Dim objRegExp As New Regex(strRegUrlEmail, RegexOptions.IgnoreCase) 'Match URLs and emails Dim MatchList As MatchCollection = objRegExp.Matches(inText) If MatchList.Count <> 0 Then objMatches = objRegExp.Matches(inText) For Each Match In MatchList iEnd = Match.Index strBuf = strBuf & Mid(inText, iStart, iEnd - iStart + 1) If InStr(1, Match.Value, "@") Then strBuf = strBuf & HrefGet(Match.Value, "EMAIL", "_BLANK") Else strBuf = strBuf & HrefGet(Match.Value, "WEB", "_BLANK") End If iStart = iEnd + Match.Length + 1 Next strBuf = strBuf & Mid(inText, iStart) InsertHyperlinks = strBuf Else 'No hyperlinks to replace InsertHyperlinks = inText End If End Function Shared Function HrefGet(ByVal url As String, ByVal urlType As String, ByVal Target As String) As String Dim strBuf As String strBuf = "<a href=""" If UCase(urlType) = "WEB" Then If LCase(Left(url, 3)) = "www" Then strBuf = "<a href=""http://" & url & """ Target=""" & _ Target & """>" & url & "</a>" Else strBuf = "<a href=""" & url & """ Target=""" & _ Target & """>" & url & "</a>" End If ElseIf UCase(urlType) = "EMAIL" Then strBuf = "<a href=""mailto:" & url & """ Target=""" & _ Target & """>" & url & "</a>" End If HrefGet = strBuf End Function ===== Sample Text ============= This would be the inText parameter. Midway through the ride, we see a Skip this too. But sometimes we go here [insert normal www dot link dot com]. If you'd like to join us contact Bill Smith at [email protected]. Thanks! sorry stack overflow won't allow multiple hyperlinks to be added. ===== End Sample Text =============

Read the article

Why does Keychain Services return the wrong keychain content?

- by Graham Lee

I've been trying to use persistent keychain references in an iPhone application. I found that if I created two different keychain items, I would get a different persistent reference each time (they look like 'genp.......1', 'genp.......2', …). However, attempts to look up the items by persistent reference always returned the content of the first item. Why should this be? I confirmed that my keychain-saving code was definitely creating new items in each case (rather than updating existing items), and was not getting any errors. And as I say, Keychain Services is giving a different persistent reference for each item. I've managed to solve my immediate problem by searching for keychain items by attribute rather than persistent references, but it would be easier to use persistent references so I'd appreciate solving this problem. Here's my code: - (NSString *)keychainItemWithName: (NSString *)name { NSString *path = [GLApplicationSupportFolder() stringByAppendingPathComponent: name]; NSData *persistentRef = [NSData dataWithContentsOfFile: path]; if (!persistentRef) { NSLog(@"no persistent reference for name: %@", name); return nil; } NSArray *refs = [NSArray arrayWithObject: persistentRef]; //get the data CFMutableDictionaryRef params = CFDictionaryCreateMutable(NULL, 0, &kCFTypeDictionaryKeyCallBacks, &kCFTypeDictionaryValueCallBacks); CFDictionaryAddValue(params, kSecMatchItemList, refs); CFDictionaryAddValue(params, kSecClass, kSecClassGenericPassword); CFDictionaryAddValue(params, kSecReturnData, kCFBooleanTrue); CFDataRef item = NULL; OSStatus result = SecItemCopyMatching(params, (CFTypeRef *)&item); CFRelease(params); if (result != errSecSuccess) { NSLog(@"error %d retrieving keychain reference for name: %@", result, name); return nil; } NSString *token = [[NSString alloc] initWithData: (NSData *)item encoding: NSUTF8StringEncoding]; CFRelease(item); return [token autorelease]; } - (void)setKeychainItem: (NSString *)newToken forName: (NSString *)name { NSData *tokenData = [newToken dataUsingEncoding: NSUTF8StringEncoding]; //firstly, find out whether the item already exists NSDictionary *searchAttributes = [NSDictionary dictionaryWithObjectsAndKeys: name, kSecAttrAccount, kCFBooleanTrue, kSecReturnAttributes, nil]; NSDictionary *foundAttrs = nil; OSStatus searchResult = SecItemCopyMatching((CFDictionaryRef)searchAttributes, (CFTypeRef *)&foundAttrs); if (noErr == searchResult) { NSMutableDictionary *toStore = [foundAttrs mutableCopy]; [toStore setObject: tokenData forKey: (id)kSecValueData]; OSStatus result = SecItemUpdate((CFDictionaryRef)foundAttrs, (CFDictionaryRef)toStore); if (result != errSecSuccess) { NSLog(@"error %d updating keychain", result); } [toStore release]; return; } //need to create the item. CFMutableDictionaryRef params = CFDictionaryCreateMutable(NULL, 0, &kCFTypeDictionaryKeyCallBacks, &kCFTypeDictionaryValueCallBacks); CFDictionaryAddValue(params, kSecClass, kSecClassGenericPassword); CFDictionaryAddValue(params, kSecAttrAccount, name); CFDictionaryAddValue(params, kSecReturnPersistentRef, kCFBooleanTrue); CFDictionaryAddValue(params, kSecValueData, tokenData); NSData *persistentRef = nil; OSStatus result = SecItemAdd(params, (CFTypeRef *)&persistentRef); CFRelease(params); if (result != errSecSuccess) { NSLog(@"error %d from keychain services", result); return; } NSString *path = [GLApplicationSupportFolder() stringByAppendingPathComponent: name]; [persistentRef writeToFile: path atomically: NO]; [persistentRef release]; }

Read the article

Model Object called in NSOutlineView DataSource Method Crashing App

- by Alec Sloman

I have a bewildering problem, hoping someone can assist: I have a model object, called Road. Here's the interface. @@@ @interface RoadModel : NSObject { NSString *_id; NSString *roadmapID; NSString *routeID; NSString *title; NSString *description; NSNumber *collapsed; NSNumber *isRoute; NSString *staff; NSNumber *start; NSArray *staffList; NSMutableArray *updates; NSMutableArray *uploads; NSMutableArray *subRoads; } @property (nonatomic, copy) NSString *_id; @property (nonatomic, copy) NSString *roadmapID; @property (nonatomic, copy) NSString *routeID; @property (nonatomic, copy) NSString *title; @property (nonatomic, copy) NSString *description; @property (nonatomic, copy) NSNumber *collapsed; @property (nonatomic, copy) NSNumber *isRoute; @property (nonatomic, copy) NSString *staff; @property (nonatomic, copy) NSNumber *start; @property (nonatomic, copy) NSArray *staffList; @property (nonatomic, copy) NSMutableArray *updates; @property (nonatomic, copy) NSMutableArray *uploads; @property (nonatomic, copy) NSMutableArray *subRoads; - (id)initWithJSONObject:(NSDictionary *)JSONObject; @end This part is fine. To give you some background, I'm translating a bunch of JSON into a proper model object so it's easier to work with. Now, I'm trying to display this in an NSOutlineView. This is where the problem is. In particular, I have created the table and a datasource. - (id)initWithRoads:(NSArray *)roads { if (self = [super init]) root = [[NSMutableArray alloc] initWithArray:roads]; return self; } - (NSInteger)outlineView:(NSOutlineView *)outlineView numberOfChildrenOfItem:(id)item { if (item == nil) return root.count; return 0; } - (BOOL)outlineView:(NSOutlineView *)outlineView isItemExpandable:(id)item { return NO; } - (id)outlineView:(NSOutlineView *)outlineView child:(NSInteger)index ofItem:(id)item { if (item == nil) item = root; if (item == root) return [root objectAtIndex:index]; return nil; } - (id)outlineView:(NSOutlineView *)outlineView objectValueForTableColumn:(NSTableColumn *)tableColumn byItem:(id)item { return [item title]; } In the final datasource method, it attempts to return the "title" string property of the model object, but for some reason crashes each time. I have checked that the method is taking in the correct object (I checked [item class] description], and it is the right object), but for some reason if I call any of the objects accessors the app immediately crashes. This is totally puzzling because in the init method, I can iterate through root (an array of RoadModel objects), and print any of its properties without issue. It is only when I'm trying to access the properties in any of the datasource methods that this occurs. I wonder if there is something memory-wise that is going on behind the scenes and I am not providing for it. If you can shed some light on to this situation, it would be greatly appreciated! Thanks in advance!

Read the article

Issue with translating a delegate function from c# to vb.net for use with Google OAuth 2

- by Jeremy

I've been trying to translate a Google OAuth 2 example from C# to Vb.net for a co-worker's project. I'm having on end of issues translating the following methods: private OAuth2Authenticator<WebServerClient> CreateAuthenticator() { // Register the authenticator. var provider = new WebServerClient(GoogleAuthenticationServer.Description); provider.ClientIdentifier = ClientCredentials.ClientID; provider.ClientSecret = ClientCredentials.ClientSecret; var authenticator = new OAuth2Authenticator<WebServerClient>(provider, GetAuthorization) { NoCaching = true }; return authenticator; } private IAuthorizationState GetAuthorization(WebServerClient client) { // If this user is already authenticated, then just return the auth state. IAuthorizationState state = AuthState; if (state != null) { return state; } // Check if an authorization request already is in progress. state = client.ProcessUserAuthorization(new HttpRequestInfo(HttpContext.Current.Request)); if (state != null && (!string.IsNullOrEmpty(state.AccessToken) || !string.IsNullOrEmpty(state.RefreshToken))) { // Store and return the credentials. HttpContext.Current.Session["AUTH_STATE"] = _state = state; return state; } // Otherwise do a new authorization request. string scope = TasksService.Scopes.TasksReadonly.GetStringValue(); OutgoingWebResponse response = client.PrepareRequestUserAuthorization(new[] { scope }); response.Send(); // Will throw a ThreadAbortException to prevent sending another response. return null; } The main issue being this line: var authenticator = new OAuth2Authenticator<WebServerClient>(provider, GetAuthorization) { NoCaching = true }; The Method signature reads as for this particular line reads as follows: Public Sub New(tokenProvider As TClient, authProvider As System.Func(Of TClient, DotNetOpenAuth.OAuth2.IAuthorizationState)) My understanding of Delegate functions in VB.net isn't the greatest. However I have read over all of the MSDN documentation and other relevant resources on the web, but I'm still stuck as to how to translate this particular line. So far all of my attempts have resulted in either the a cast error (see below) or no call to GetAuthorization. The Code (vb.net on .net 3.5) Private Function CreateAuthenticator() As OAuth2Authenticator(Of WebServerClient) ' Register the authenticator. Dim client As New WebServerClient(GoogleAuthenticationServer.Description, oauth.ClientID, oauth.ClientSecret) Dim authDelegate As Func(Of WebServerClient, IAuthorizationState) = AddressOf GetAuthorization Dim authenticator = New OAuth2Authenticator(Of WebServerClient)(client, authDelegate) With {.NoCaching = True} 'Dim authenticator = New OAuth2Authenticator(Of WebServerClient)(client, GetAuthorization(client)) With {.NoCaching = True} 'Dim authenticator = New OAuth2Authenticator(Of WebServerClient)(client, New Func(Of WebServerClient, IAuthorizationState)(Function(c) GetAuthorization(c))) With {.NoCaching = True} 'Dim authenticator = New OAuth2Authenticator(Of WebServerClient)(client, New Func(Of WebServerClient, IAuthorizationState)(AddressOf GetAuthorization)) With {.NoCaching = True} Return authenticator End Function Private Function GetAuthorization(arg As WebServerClient) As IAuthorizationState ' If this user is already authenticated, then just return the auth state. Dim state As IAuthorizationState = AuthState If (Not state Is Nothing) Then Return state End If ' Check if an authorization request already is in progress. state = arg.ProcessUserAuthorization(New HttpRequestInfo(HttpContext.Current.Request)) If (state IsNot Nothing) Then If ((String.IsNullOrEmpty(state.AccessToken) = False Or String.IsNullOrEmpty(state.RefreshToken) = False)) Then ' Store Credentials HttpContext.Current.Session("AUTH_STATE") = state _state = state Return state End If End If ' Otherwise do a new authorization request. Dim scope As String = AnalyticsService.Scopes.AnalyticsReadonly.GetStringValue() Dim _response As OutgoingWebResponse = arg.PrepareRequestUserAuthorization(New String() {scope}) ' Add Offline Access and forced Approval _response.Headers("location") += "&access_type=offline&approval_prompt=force" _response.Send() ' Will throw a ThreadAbortException to prevent sending another response. Return Nothing End Function The Cast Error Server Error in '/' Application. Unable to cast object of type 'DotNetOpenAuth.OAuth2.AuthorizationState' to type 'System.Func`2[DotNetOpenAuth.OAuth2.WebServerClient,DotNetOpenAuth.OAuth2.IAuthorizationState]'. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.InvalidCastException: Unable to cast object of type 'DotNetOpenAuth.OAuth2.AuthorizationState' to type 'System.Func`2[DotNetOpenAuth.OAuth2.WebServerClient,DotNetOpenAuth.OAuth2.IAuthorizationState]'. I've spent the better part of a day on this, and it's starting to drive me nuts. Help is much appreciated.

Read the article

Maven not setting classpath for dependencies properly

- by Matthew

OS name: "linux" version: "2.6.32-27-generic" arch: "i386" Family: "unix" Apache Maven 2.2.1 (r801777; 2009-08-06 12:16:01-0700) Java version: 1.6.0_20 I am trying to use the mysql dependency in with maven in ubuntu. If I move the "mysql-connector-java-5.1.14.jar" file that maven downloaded into my $JAVA_HOME/jre/lib/ext/ folder, everything is fine when I run the jar. I think I should be able to just specify the dependency in the pom.xml file and maven should take care of setting the classpath for the dependency jars automatically. Is this incorrect? My pom.xml file looks like this: <project xmlns="http://maven.apache.org/POM/4.0.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://maven.apache.org/POM/4.0.0 http://maven.apache.org/xsd/maven-4.0.0.xsd"> <modelVersion>4.0.0</modelVersion> <groupId>com.ion.common</groupId> <artifactId>TestPreparation</artifactId> <version>1.0-SNAPSHOT</version> <packaging>jar</packaging> <name>TestPrep</name> <url>http://maven.apache.org</url> <properties> <project.build.sourceEncoding>UTF-8</project.build.sourceEncoding> </properties> <build> <plugins> <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-jar-plugin</artifactId> <configuration> <archive> <manifest> <addClasspath>true</addClasspath> <mainClass>com.ion.common.App</mainClass> </manifest> </archive> </configuration> </plugin> </plugins> </build> <dependencies>  <dependency> <groupId>junit</groupId> <artifactId>junit</artifactId> <version>3.8.1</version> <scope>test</scope> </dependency>  <dependency> <groupId>mysql</groupId> <artifactId>mysql-connector-java</artifactId> <version>5.1.14</version> <scope>compile</scope> </dependency> </dependencies> </project> The command "mvn package" builds it without any problems, and I can run it, but when the application attempts to access the database, this error is presented: java.lang.ClassNotFoundException: com.mysql.jdbc.Driver at java.net.URLClassLoader$1.run(URLClassLoader.java:217) at java.security.AccessController.doPrivileged(Native Method) at java.net.URLClassLoader.findClass(URLClassLoader.java:205) at java.lang.ClassLoader.loadClass(ClassLoader.java:321) at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:294) at java.lang.ClassLoader.loadClass(ClassLoader.java:266) at java.lang.Class.forName0(Native Method) at java.lang.Class.forName(Class.java:186) at com.ion.common.Functions.databases(Functions.java:107) at com.ion.common.App.main(App.java:31) The line it is failing on is: Class.forName("com.mysql.jdbc.Driver"); Can anyone tell me what I'm doing wrong or how to fix it?

Search Results

Search found 11227 results on 450 pages for 'login attempts'.

Page 422/450 | < Previous Page | 418 419 420 421 422 423 424 425 426 427 428 429 | Next Page >

- by user3712955

- by Timothy

- by Mike B

- by Aidan

- by AMissico

- by fooyee

- by Wonko the Sane

- by Dor

- by wnoveno

- by sidha

- by Simon

- by Bobby

- by Seidr

- by portoalet

- by AMissico

- by Denise

- by Chris Leah

- by Ryan Smyth

- by exhuma

- by davebug

- by Scott Sumpter

- by Graham Lee

- by Alec Sloman

- by Jeremy

- by Matthew

< Previous Page | 418 419 420 421 422 423 424 425 426 427 428 429 | Next Page >