Search Results

Search found 37414 results on 1497 pages for 'open port'.

Page 423/1497 | < Previous Page | 419 420 421 422 423 424 425 426 427 428 429 430  | Next Page >

• Extending partition on linux gparted but not more space in the vm

  - by Asken

  I have a vm test installation of a linux running a build server. Unfortunately I just pressed ok when adding the disk and ended up with an 8gb drive to play with. Well into the test the builds are consuming more and more space, of course. The vm drive was resized to 21gb and using gparted I expanded the drive partitions and that all worked fine but when I go back into the console and do df there's still only 8gb available. How can I claim the other 13gb I added? fdisk -l Disk /dev/sda: 21.0 GB, 20971520000 bytes 255 heads, 63 sectors/track, 2549 cylinders, total 40960000 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0006d284 Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 40959999 20229121 5 Extended /dev/sda5 501760 40959999 20229120 8e Linux LVM vgdisplay --- Volume group --- VG Name ct System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 2 Max PV 0 Cur PV 1 Act PV 1 VG Size 19.29 GiB PE Size 4.00 MiB Total PE 4938 Alloc PE / Size 1977 / 7.72 GiB Free PE / Size 2961 / 11.57 GiB VG UUID MwiMAz-52e1-iGVf-eL4f-P5lq-FvRA-L73Sl3 lvdisplay --- Logical volume --- LV Name /dev/ct/root VG Name ct LV UUID Rfk9fh-kqdM-q7t5-ml6i-EjE8-nMtU-usBF0m LV Write Access read/write LV Status available # open 1 LV Size 5.73 GiB Current LE 1466 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:0 --- Logical volume --- LV Name /dev/ct/swap_1 VG Name ct LV UUID BLFaa6-1f5T-4MM0-5goV-1aur-nzl9-sNLXIs LV Write Access read/write LV Status available # open 2 LV Size 2.00 GiB Current LE 511 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 252:1

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• Access to CD/DVD Drive is Denied through Windows 7 Explorer (Permission Problem)

  - by Synetech inc.

  A while ago I started having trouble with my optical drives. Both of them keep showing up in Explorer as CD/DVD drives on boot, but as soon as I put a disc in either one, it suddenly turns into a hard-drive—“local disk” is displayed in the Type column, though the File System column remains UDF/CDFS. (I though that maybe it was a permission issue on the registry key in HKLM\System\CurrentControlSet..., but I’m not so certain because of the next test.) When I try to open a disc (of any type), I get an access denied error message. If I open an elevated command-prompt, I am able to access the files. Also, if I kill Explorer and run it from an elevated command-prompt (thus giving Explorer elevated permissions), then I can access the files from Explorer. I’ve tried uninstalling and reinstalling the devices without success. The security dialog indicates that there are none set for the drives (no owner and no permissions). I tried setting the owner, but am only able to do so if there is a disc in it (it complains if it is empty), but the settings do not stick (if I immediately open the security dialog after setting it, it is empty again). I tried setting permissions, but that gives an error. I’ve included a screencap-flowchart of the security dialog of one of the drives below. (Yes, I made sure that there are no upper- or lower-filters, and yes, I ran sfc. I also made sure that in the policy editor, “devices: restrict CD-ROM...” is not set.) Does anyone know what the owner and permissions are supposed to be for optical drives and how to reset them?

  Read the article

• Changing the View of a Folder When It Is Opened from Finder

  - by user60044

  When I was running OS 10.4 I had all my folders beautifully organized with position and which ones should be opened in View mode and which one in Icon, etc. When I transitioned to 10.6 I found that OS ignored all that information and imposes an awful consequence of changing the view for some folder and that view moving up to all parent folders which don't have their views locked. The only way I can think of to get this functionality back is to either write a program that given a root directory will enumerate it setting the views based upon a static template I have. The other way I thought I could accomplish this is by Folder Actions. Aside from the fact that I don't know AppleScript it seems folder actions cannot be inherited. Since I have 1000s of folders involved here, all being inherited from a single root, I could not possibly manually add that action to each of those folders. What I would like to have is a folder action that whenever I open the folder from Finder, then if it contains any JPG, GIF, etc. type image files that it will automatically open that folder with a view of Icon with a reasonable size to support the number of images. If the folder contains only folders, then to open that folder in the list view. Does anyone have anything that could do this for me? Thank You, -- Mark

  Read the article

• How do i play nicely with MS SQL/SQL Server 2008

  - by acidzombie24

  Big problem. I have nearly given up. I am trying to port my prototype to use MS SQL so it will work on a server once i get it (the server will be SQL Server 2008, shared, i dont know any more info). So i tried to connect to SQL Server via visual studios IDE and had no luck. I enabled TCP and named pipes and restarted the service (and computer) with still no luck. I remembered about mdf files so i made that after an obstacle of not being able to make the connect string require i figure out visual studio has it in its properties and successfully connected with that. Then i had a problem with nested transactions. After not being able to figure out how to check i wondered if i can configure it to allow it somehow. I always thought all of MS were the same except for limitations but sql server seems to support nested transactions so theres no point trying to work around the problem with .mdf files since i wont need them and really just used it to port the base of my sql code and to check if syntax is correct. I tried installing SQL Server Management Studio since people mentioned it several times (as a solution or at least help). When installing it on windows 7 it says it may not be compatible. After running it, it launched SQL Server Installation Center (64-bit) which doesnt seem to be the same thing as i dont see a way to modify any of my server (networking) configurations or edit user permissions, etc. I am clueless what to do next. Does anyone have any ideas? I'm posting here bc i think my problem is more configurations and sql server then programming.

  Read the article

• How to diagnose issue between mobo, RAID, and SSD cache drive? [migrated]

  - by goober

  Background This issue is happening on my custom-built desktop. Relevant specs: Motherboard: ASUS P8Z68-V PRO Utilizing Intel RST technology (application that uses unused SSD as cache) Processor: Intel core i7-2600k (not overclocked) HDDs: RAID1 of 2x Seagate Barracuda 1TB (ST31000524AS) (RAID performed via z68 chipset) Machine has run fine for ~1 year with no issues, and has been well-maintained (dust, etc.) What Happened Random Freezing issues -- intermittent Looked at the RST application screen to see that the acceleration cache was listed as "unavailable" -- recommended that I power down and reconnect the drive. Reconnected the drive to no avail. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Now, the freeze happens whenever loading something particularly data-driven (a video, a game, etc.) Steps Attempted Reconnected the drive to no avail. Updated Intel RST software to v. 11.6.0.1030 to see if that made a difference. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Connected the drive as its own volume. Formatted it, ran disk check errors -- all seems fine. Reconnected the drive and selected it again as the cache drive. Now, what happens when there is a freeze: Machine freezes I am unable to perform any command Screen then goes black I hit the reset button During boot, all drives show as "Disabled" and I am told no volume can be found I then hit the reset button (or power off/on) again. Either the next time (or sometimes after repeating this once more), the metadata cache is reconstructed and the system boots fine, showing the SSD as a cache. Question I believe this is an issue with the SSD itself, but how can I be sure since connecting it separately appeared to show no problems? I want to make sure it's not an issue with the motherboard, SATA ports, etc.

  Read the article

• empty file from tomcat https redirect?

  - by amertune

  I am using tomcat 6.0.20, with jdk 1.6.0_18 on 64 bit linux (tomcat downloaded from tomcat.apache.org, not installed from repositories). I have iptables redirects from port 80 - 8080 and 443 - 8443. In server.xml, the connector for port 8080 redirects to 443, and the 8443 connector has proxyPort="443". In conf/web.xml, I have added this bit at the end of the file (but still inside the <web-app</webapp tags). <security-constraint> <web-resource-collection> <web-resource-name>Protected Context</web-resource-name> <url-pattern>/*</url-pattern> </web-resource-collection> <user-data-constraint> <transport-guarantee>CONFIDENTIAL</transport-guarantee> </user-data-constraint> </security-constraint> I also have two contexts, ROOT and mywebapp. If I go to http://myurl.com, then I get redirected to https://myurl.com. If I go to http://myurl.com/mywebapp/, then I get redirected to https://myurl.com/mywebapp/. The problem I'm having is when I go to http://myurl.com/mywebapp (no trailing slash). When I do this I get a prompt to download an empty file that has an empty name. Going to https://myurl.com/mywebapp works. I would think that a user typing myurl.com/mywebapp is far from rare. Is there something I'm missing?

  Read the article

• IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

  - by NVRAM

  I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

  Read the article

• Apache mod_proxy

  - by mhouston100

  Uggh, I'm spewing that I can't figure this out, I'm so frustrated: <VirtualHost *:80> servername domain1.com.au ServerAdmin webmaster@localhost DocumentRoot /var/www/html ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined <Proxy *> Order Allow,Deny Allow from all </Proxy> RewriteEngine on ReWriteCond %{SERVER_PORT} !^443$ RewriteRule ^/(.*) https://%{HTTP_HOST}/$1 [NC,R,L] </VirtualHost> <VirtualHost *:443> servername domain1.com.au SSLEngine on SSLCertificateFile /etc/apache2/ssl/owncloud.pem SSLCertificateKeyFile /etc/apache2/ssl/owncloud.key DocumentRoot /var/www/html </VirtualHost> <VirtualHost *:*> Servername domain2.com.au ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / https://192.168.1.12/ ProxyPassReverse / https://192.168.1.12/ </VirtualHost> Not sure if it's clear what I'm trying to do, but I've read and read and READ, I still can't figure it out. Basically I have a working Apache server with a rewrite to force HTTPS, as seen in the first two VirtualHost entries. I now have a webmail service I set up on another server, under another domain name, however I only have one incoming public IP address. So I'm trying to have any incoming requests for the second domain to be proxied to the other server to access the webmail, whether its port 80 or 443. IMAP and POP3 are no problems, I can just forward the ports directly to the correct server. The results of the above configuration is that requests to domain2.com.au (port 80 or 443) are forwarded to https://domain1.com.au. Am I headed in the right direction?

  Read the article

• What differences are there between "home" switches and "professional" switches?

  - by pjreddie

  Our radio station uses a PtP wireless system to stream our radio and TV signals from our studio up a hill to our transmitter. We have been having problems with warbly sound and drop outs that come from some point in this system. An engineer that occasionally visits the station thinks it could be the switches we use on each side of the PtP wireless system to connect the PtP devices to the encoders and decoders and wants us to get two of these switches: http://www.amazon.com/Netgear-JGS516-ProSafe-16-Port-Ethernet/dp/B0002CWPOK/ref=dp_return_1 The encoder/decoder setup only streams 8Mbps total so it seems like the switches we have should not be stressed out, unless they are causing sufficient latency to degrade the performance of the encoder/decoder. At each end of the connection we only have 4 connections, is there any reason we couldn't get a cheaper, "home" quality switch like this: http://www.amazon.com/D-Link-DGS-1005G-5-Port-Gigabit-Desktop/dp/tech-data/B003X7TRWE/ref=de_a_smtd Is there a significant difference that we would notice in terms of latency between these two switches? How much does the quality of the switch actually matter in this scenario? Any help is appreciated, feel free to ask questions if anything needs clarification. Thanks

  Read the article

• Apache Virtual Hosts behind Cisco Router

  - by Theo

  I'm setting up an Apache 2.2 Ubuntu web server for internal services that is also supposed to be accessed from outside our LAN. Our LAN has a single external IP that is the external IP of our RV042 Cisco router. We have set up several A records on our external DNS server that point to this IP. Our internal DNS server resolve the same records to the internal IP of our web server, so computers from inside the network can access them using the same address as if they were outside. We forwarded the router's external 80 port to our web server's 80 port. I have set up one Virtual Host for each domain name in our list, and my httpd.conf is something like this: ServerName web.domain.com NameVirtualHost *:80 <VirtualHost *:80> ServerName alfresco.domain.com <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /alfresco http://localhost:8080/alfresco ProxyPassReverse /alfresco http://localhost:8080/alfresco ProxyPass /share http://localhost:8080/share ProxyPassReverse /share http://localhost:8080/share </VirtualHost> <VirtualHost *:80> ServerName crm.domain.com DocumentRoot /var/www/sugarcrm </VirtualHost> Now, this works if we are in our LAN. However, if we are outside of our LAN we reach our web server's default page saying: It Works! This is the default web page for this server. But we can't reach the virtual hosts, as if the domain name is not being preserved when the router forward the packets to the web server. Am I doing something wrong? How can I check what is going on? What should be the settings to make this work from outside?

  Read the article

• LVS / IPVS difference in ActiveConn since upgrading

  - by Hans

  I've recently migrated from an old version of LVS / ldirectord (Ultra Monkey) to a new Debian install with ldirectord. Now the amount of Active Connections is usually higher than the amount of Inactive Connections, it used to be the other way around. Basically on the old load balancer the connections looked something like: -> RemoteAddress:Port Forward Weight ActiveConn InActConn -> 10.84.32.21:0 Masq 1 12 252 -> 10.84.32.22:0 Masq 1 18 368 However since migrating it to the new load balancer it looks more like: -> RemoteAddress:Port Forward Weight ActiveConn InActConn -> 10.84.32.21:0 Masq 1 313 141 -> 10.84.32.22:0 Masq 1 276 183 Old load balancer: Debian 3.1 ipvsadm 1.24 ldirectord 1.2.3 New load balancer: Debian 6.0.5 ipvsadm 1.25 ldirectord 1.0.3 (I guess the versioning system changed) Is it because the old load balancer was running a kernel from 2005, and ldirectord from 2004, and things have simply changed in the past 7 - 8 years? Did I miss some sysctl settings that I should be enforcing for it to behave in the same way? Everything appears to be working fine but can anyone see an issue with this behaviour? Thanks in advance! Additional info: I'm using LVS in masquerading mode, the real servers have the load balancer as their gateway. The real servers are running Apache, which hasn't changed during the upgrade. The boxes themselves show roughly the same amount of Inactive Connections shown in ipvsadm.

  Read the article

• Tuning up a MySQL server

  - by NinjaCat

  I inherited a mysql server, and so I've started with running the MySQLTuner.pl script. I am not a MySQL expert but I can see that there is definitely a mess here. I'm not looking to go after every single thing that needs fixing and tuning, but I do want to grab the major, low hanging fruit. Total Memory on the system is: 512MB. Yes, I know it's low, but it's what we have for the time being. Here's what the script had to say: General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries When making adjustments, make tmp_table_size/max_heap_table_size equal Reduce your SELECT DISTINCT queries without LIMIT clauses Increase table_cache gradually to avoid file descriptor limits Your applications are not closing MySQL connections properly Variables to adjust: query_cache_limit (> 1M, or use smaller result sets) tmp_table_size (> 16M) max_heap_table_size (> 16M) table_cache (> 64) innodb_buffer_pool_size (>= 326M) For the variables that it recommends that I adjust, I don't even see most of them in the mysql.cnf file. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_buffer_pool_size = 220M innodb_flush_log_at_trx_commit = 2 innodb_file_per_table = 1 innodb_thread_concurrency = 32 skip-locking big-tables max_connections = 50 innodb_lock_wait_timeout = 600 slave_transaction_retries = 10 innodb_table_locks = 0 innodb_additional_mem_pool_size = 20M user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking bind-address = localhost key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 4 myisam-recover = BACKUP query_cache_limit = 1M query_cache_size = 16M log_error = /var/log/mysql/error.log expire_logs_days = 10 max_binlog_size = 100M skip-locking innodb_file_per_table = 1 big-tables [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] [isamchk] key_buffer = 16M !includedir /etc/mysql/conf.d/

  Read the article

• Vagrant VM Fails to Boot

  - by Rob Wilkerson

  I have a Vagrant environment that requires me to forward port 80 so I bring it up under sudo on an OS X machine. This has always been fine until I recently upgraded to Vagrant 1.2.2. Now it fails to boot. [default] Waiting for VM to boot. This can take a few minutes. [default] Failed to connect to VM! Failed to connect to VM via SSH. Please verify the VM successfully booted by looking at the VirtualBox GUI. Because I'm running under sudo, the machine never gets added to the Virtualbox GUI, but that's always been the case for this environment. I don't get any indication that there was a problem with the additions -- a potential source of this error, from what I've read. I can bring things up just fine if I change to using port 8080 on the host machine. I can't use the app, but the VM itself loads up and provisions nicely. As far as I can tell, the only thing that's changed is: I upgraded my Vagrant version I updated the project's Vagrantfile to use v2 syntax. Anyone have any idea what I might be missing? I thought I'd be able to find this pretty easily, but it's quickly becoming a very real problem.

  Read the article

• Doesn't work Nginx + SSI

  - by boopidoopi

  I have some problems. Nginx doesn't work with SSI. Nginx listens 80 port (frontend), apache2 listens 81 port (backend). That is my nginx configurations: server { listen 80; server_name test.dev www.test.dev; error_log /var/log/nginx/error.log debug; log_subrequest on; location / { ssi on; proxy_pass http://localhost:81; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 15m; client_body_buffer_size 128k; } } SSI include in test.dev index.php: <!--# include virtual="http:test.dev/test.html" -- When I open test.dev/index.php I see clean page. In page source: <!--# include virtual="http:test.dev/test.html" -- So how to enable SSI in nginx? Can you help me?

  Read the article

• linux networking: how to redirect incoming connections from old server to new server?

  - by aliz

  hi I'm in the process of moving my old server to a new server, but i will keep the old server running for database replication and load balancing, etc. each server has a separate internet connection with a static ip, and they are connected through a local Ethernet connection. I've got Ubuntu 8.04 32-bit running on old server and Debian 6.0 64-bit on new one. shorewall firewall is installed on both servers. there are some outdoor devices which are periodically sending data to port 43597 for old server IP address. I can run multiple instances of the network service which is responsible for receiving data from devices on a server but on different ports. here's the question: how can I run the service on new server and have connections coming to old server redirected to it, and new devices can still connect to new server's IP address preferably on the same port and same service? until all devices get updated to send to new server. I've tried a shorewall DNAT rule, but seems like new server's default route should be changed to ethernet connection, which breaks other things. I also found about redir utility, but still haven't tried it. is there any best practice or simple solution for such a scenario, i'm not aware of? thanks in advance.

  Read the article

• RAID5 issue after replacing motherboard and upgrading firmware

  - by 8steve8

  ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with Windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. This screenshot should show that the SNs match, which raises the question why the software doesn't realize the drive is a member of the array. I'd like to know if anyone has experienced anything similar, and what should I do, can I force the drive to be recognized as a member (without wiping data)?

  Read the article

• 403 Forbiden on Apache (CentOS) Server

  - by pouya

  These are my VM setup: HOST: windows 7 ultimate 32bit GUEST: CentOs 6.3 i386 Virtualization soft: Oracle virtualBox 4.1.22 Networking: NAT -> (PORT FORWARD: HOST:8080 => GUEST:80) Shared Folder: centos all the project files goes into shared folder and for each project file a virtualhost conf file is created in /etc/httpd/conf.d/ like /etc/httpd/conf.d/$domain I wasn't able to see anything in my browser before disabling both windows firewall and iptables in centos after that if i type for example: http://www.$domain:8080/ all i see is: Forbidden You don't have permission to access / on this server. Apache/2.2.15 (CentOS) Server at www.$domain.com Port 8080 A sample Virtual Host conf file: <VirtualHost *:80> #General DocumentRoot /media/sf_centos/path/to/public_html ServerAdmin webmaster@$domain ServerName www.$domain ServerAlias $domain *.$domain #Logging ErrorLog /var/log/httpd/$domain-error.log CustomLog /var/log/httpd/$domain-access.log combined #mod rewrite RewriteEngine On RewriteLog /var/log/httpd/$domain-rewrite.log RewriteLogLevel 0 </VirtualHost> centos shared folder is availabe to guest at /media/sf_centos These are file permissons for sf_centos: drwxrwx--- root vboxsf vboxsf group includes: apache and root So these are my questions: 1- How to solve Forbidden Problem? 2- How to setup both host and guest firewalls? 3- How can i improve this developement environment to simulate production environment as much as possible specially security improvements?

  Read the article

• Server Intermittently Inaccessible Externally (but Accessible Internally Continuously)

  - by nicorellius

  I have a CRM on a server on a network. We have a static IP and another server outward facing. We use port-forwarding to map to the CRM, so that when you go to the IP or the FQDN, you get to the CRM: xxx.xxx.xxx.xxx crm.example.com Internally, we can access the CRM by going to crm or crm.example.com Lately, I've been noticing that accessing the server from outside the network times out or gives 503, bad gateway. During that time, I can also SSH (different port, so this works) into the outward facing computer and access the server just fine. I have a robot monitoring the site and indeed via HTTP monitoring the site is going down periodically. I looked through the Apache server access and error logs and nothing stuck out at me so I'm a bit confused as to what could be going on. I also searched the access logs for 503 and found nothing. When I run tracert from outside the network, it appears the packets basically make it through the wider area servers (Comcast city and county servers) and end up dropping at the CRM server's front step. I'm tempted to replace the server because it is older and underpowered but it would be nice to know what is going on. Any ideas what to do next?

  Read the article

• How to setup apache to catch a proxy_pass from nginx?

  - by Paté

  I have a working apache vhost such as <VirtualHost localhost:10006> DocumentRoot "/home/pate/***/git/kohana_site/public/site/" </VirtualHost> <VirtualHost *:10006> ServerName api.* DocumentRoot "/home/pate/***/git/kohana_site/public/api/" LogLevel debug </VirtualHost> If i point to localhost:10006 I get my website and api.localhost:10006 I get my api. Then I have haproxy setup on top of that, that runs on port 10010 and both localhost:10010 and api.localhost:10010 have the expected behaviour. Now I have nginx setup on port 80 with this configuration. server { listen 10000; server_name api.*; location / { proxy_pass http://legacy_server; } } server { listen 10000 default; server_name _; location /nginx_status { stub_status on; access_log off; } # images are accessed via the CDN over HTTP (not https) location /n/image { proxy_pass http://image_caching_server; } location / { return 301 https://$host:10014$request_uri; } } upstream legacy_server { server localhost:10010 fail_timeout=0; } the problem is that apache does not recognize the vhost properly and redirects api.localhost to the website instead of the api. I tried playing with set_proxy_header Host $host but it doesn't seem to do anything.

  Read the article

• Cannot make bind9 forward DNS query to subdomain unless recursive enabled

  - by PP.

  I am trying to develop my own dynamic DNS. I'm running my own custom DNS for the subdomain on port 5353. ASCII diagram: INET --->:53 Bind 9 --->:5353 node.js | V zone_files I have example.com. The node.js DNS is for dyn.example.com. In my /etc/bind/named.conf.local I have: zone "example.com" { type master; file "/etc/bind/db.com.example"; allow-transfer { zonetxfrsafe; }; }; zone "dyn.example.com" IN { # DYNAMIC type forward; forwarders { 127.0.0.1 port 5353; }; forward only; }; I've even gone so far as to add a NS in my example.com zone file: $TTL 86400 @ IN SOA ns.example.com. hostmaster.example.com. ( 2013070104 ; Serial 7200 ; Refresh 1200 ; Retry 2419200 ; Expire 86400 ) ; Negative Cache TTL ; NS ns ; inet of our nameserver ns A 1.2.3.4 ; NS record for subdomain dyn NS ns When I attempt to get a record from the subdomain server it doesn't get forwarded: dig @127.0.0.1 test.dyn.example.com However if I turn recursive on in /etc/bind/named.conf.options: options { recursion yes; } .. then I CAN see the request going to the subdomain server. But I don't want recursion yes; in my Bind configuration as it is poor security practice (and allows all-and-sundry requests that are not related to my managed zones). How does one forward (proxy) zone queries for just one zone? Or do I give up on Bind altogether and find a DNS server that can actually forward specific queries?

  Read the article

• Embedded Windows XP

  - by Kyle

  My company acquired a brake press for bending large structural steel plates. We received it second hand and it came with an embedded copy of windows XP. Now for the part that's driving me nuts: plug and play has been turned off, also accessibility options has been disabled. What does this mean for me? Keyboards will not work! Nothing that plugs into a USB port will work and it does not have a CD ROM drive. I have tried to turn on plug and play using the on screen keyboard but it is not there since accessibility options is turned off. I would just get an updated copy of the the embedded OS but they come from Sweden and are extremely expensive. I assume there has got to be a way to get a USB devices to work. We need to get a wifi adapter on it so I can use team viewer and remotely configure it for our needs. Things to keep in mind: There is no keyboard so everything has to be done with the mouse There is no PS2 port for a keyboard just a mouse. Odd. I am 5 states away from this location and have been working with a tech who is physically installing the machine. System 32 seems to be missing A LOT of files, the tech told me there is only 8 folders in there and no other files (I don't even understand how Windows is running like this). If anyone has ANY ideas I would appreciate it, I am unsure where to go from here.

  Read the article

• Windows 7 does not detect my new hard drive?

  - by jasondavis

  I just built a really nice new PC. Some specs... Intel i7-930 CPU ASRock Extreme X58 motherboard with sata 3 and USB 3.0 12gb of G-Skill DDR3 RAM 80gb Intel G2 Solid state drive for Windows 7 and other programs to run on Windows 7 Pro 64bit OS 2 1gb grapghic cards for 4 monitor support Thats the main components. Well today my new 1tb western digital hard drive came which I plan to use for data to preserve the life of my SSD (hopefully). I hooked up it's sata power input and then hooked up it's sata data cable to a sata 2 port on my motherboard, I boot windows 7 and go into my computer and the drive is not showing up with my other drives. I then re-boot again and check again, no luck. I then shut down the PC and open the case back up, I then check my connections and they all look good. I then boot up and I can see the new HD is on and spinning. I then go into my BIOS settings to see if it registers there and it DOES! It shows I have a WD 1tb hard drvie on sata 2 port 6. So I am at a loss of why it is not showing up as an option in windows? Windows acts as if the drive is not there. Please help

  Read the article

• How do I tell Websphere 7 about a front end load balancer so that re-directs are handled correctly?

  - by TiGz

  On WebLogic 11G I can use the console to set the FrontendHost and FrondendPort on a server or on a cluster so that re-directs are handled correctly and end up resolving to the front end load balancer instead of the local host. The MBeans associated with this on WebLogic are, for example: MBean Name com.bea:Name=AdminServer,Type=WebServer,Server=AdminServer Attribute Name FrontendHost Description The name of the host to which all redirected URLs will be sent. If specified, WebLogic Server will use this value rather than the one in the HOST header. Sets the HTTP frontendHost Provides a method to ensure that the webapp will always have the correct HOST information, even when the request is coming through a firewall or a proxy. If this parameter is configured, the HOST header will be ignored and the information in this parameter will be used in its place. Type java.lang.String Readable / Writable RW How is the same thing achieved under Websphere 7? Follow up info: So I have 2 use cases actually. One is that I have a web app running under WebSphere on host A on port 9002 and a LB running on host B at port 80, when I visit the home page of the app via the LB on http://hostb/app the app redirects my browser to http://hostb:9002/app and it 404's I think this is WebSphere's fault but I guess it could be the app's fault? The second is that the web app in question needs to send emails containing URls that the customer can click on to get back into the web app - obviously this needs to be via the LB. On WebLogic the app uses MBeans to derive the LB url and I was hoping to use a similar mechanism on WebSphere.

  Read the article

< Previous Page | 419 420 421 422 423 424 425 426 427 428 429 430  | Next Page >