Search Results

Search found 12079 results on 484 pages for 'secondary ip'.

Page 425/484 | < Previous Page | 421 422 423 424 425 426 427 428 429 430 431 432  | Next Page >

• Translating IPTables rule to UFW

  - by Dario Fumagalli

  we are using an Ubuntu 12.04 x64 LTS VPS. Firewall being used is UFW. I have setup a Varnish + LEMP setup. along with other things, including an Openswan IPSEC VPN from our office to the VPS data center. A second in house Ubuntu box is to act as MySQL slave and fetch data from the VPS through the VPN. Master's ppp0 is seen as 10.1.2.1 from the slave, they ping etc. I have done the various required tasks but I can't get the client (slave) MySQL (nor telnet 10.1.2.1 3306) to access the master through the VPN unless I issue this fairly obvious IPTables command: iptables -A INPUT -s 10.1.2.0/24 -p tcp --dport 3306 -j ACCEPT I willingly forced the accepted input to come from the last octet. With this rule everything works just fine! However I want to translate this command to UFW syntax so to keep everything in one place. Now I admit being inexperienced with UFW, I prepared rules like: ufw allow proto tcp from 10.1.2.0/24 port mysql and 2-3 variations involving specifying 3306 instead of mysql, specifying a target IP (MySQL's my.cnf at the moment is configured as 0.0.0.0) and similar but I just don't seem to be able to replicate the simple iptables rule in a functional way. Anyone could kindly give me a suggestion that is not to dump UFW? Thanks in advance.

  Read the article

• Delete ARP cache on Mac OS when moving from one Wifi network to the other

  - by Puneet

  I am facing wireless connectivity problems when I move from one Wifi network to the other. Here is how it happens: I am at my friends place. I connect to his Wifi. His Wifi router ip address is 192.168.0.1. Everything is fine I close my laptop, come back to my house, open my laptop and I connect to the Wifi Network at my place. Different ESSID, but the Wifi router address is the same 192.168.0.1. At this point I cant get to anything on the internet. To debug I try to see if I can ping the router (192.168.0.1), I cant. I get a no route to host. Meanwhile airport tells me Im connected to Wifi. I see the arp cache and I see a permanent entry for 192.168.0.1 ? (192.168.0.1) at 5c:d9:98:65:73:6c on en1 permanent [ethernet] This permanent bit looks problematic. I go ahead and delete the arp cache entry and all is fine with the world until I go back to my friends place where the same situation plays out. Now my question is, why the hell is this happening? If there is no way around it, can I run a script on Wifi connect/disconnect to clear out the arp cache? Im using Mac OS X $uname -a Darwin 10.8.0 Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386 i386

  Read the article

• Windows Firewall Software to Filter Transit Traffic

  - by soonts

  I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

  Read the article

• Why is my Drupal Registration email considered spam by gmail? (headers included)

  - by Jasper

  I just created a Drupal website on a uni.cc subdomain that is brand-new also (it has barely had the 24 hours to propagate). However, when signing up for a test account, the confirmation email was marked as spam by gmail. Below are the headers of the email, which may provide some clues. Delivered-To: *my_email*@gmail.com Received: by 10.213.20.84 with SMTP id e20cs81420ebb; Mon, 19 Apr 2010 08:07:33 -0700 (PDT) Received: by 10.115.65.19 with SMTP id s19mr3930949wak.203.1271689651710; Mon, 19 Apr 2010 08:07:31 -0700 (PDT) Return-Path: <[email protected]> Received: from bat.unixbsd.info (bat.unixbsd.info [208.87.242.79]) by mx.google.com with ESMTP id 12si14637941iwn.9.2010.04.19.08.07.31; Mon, 19 Apr 2010 08:07:31 -0700 (PDT) Received-SPF: pass (google.com: best guess record for domain of [email protected] designates 208.87.242.79 as permitted sender) client-ip=208.87.242.79; Authentication-Results: mx.google.com; spf=pass (google.com: best guess record for domain of [email protected] designates 208.87.242.79 as permitted sender) [email protected] Received: from nobody by bat.unixbsd.info with local (Exim 4.69) (envelope-from <[email protected]>) id 1O3sZP-0004mH-Ra for *my_email*@gmail.com; Mon, 19 Apr 2010 08:07:32 -0700 To: *my_email*@gmail.com Subject: Account details for Test at YuGiOh Rebirth MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8; format=flowed; delsp=yes Content-Transfer-Encoding: 8Bit X-Mailer: Drupal Errors-To: info -A T- yugiohrebirth.uni.cc From: info -A T- yugiohrebirth.uni.cc Message-Id: <[email protected]> Date: Mon, 19 Apr 2010 08:07:31 -0700 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - bat.unixbsd.info X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [99 500] / [47 12] X-AntiAbuse: Sender Address Domain - bat.unixbsd.info X-Source: X-Source-Args: /usr/local/apache/bin/httpd -DSSL X-Source-Dir: gmh.ugtech.net:/public_html/YuGiOhRebirth

  Read the article

• Can I get a domain controller not to act as DNS for the members?

  - by rsw

  Hi, Let me try to explain my current setup. I have one linux machine acting as DHCP and DNS (dhcpd3 and bind) in my network. This works fine, all computers I hook up to the network gets an IP address and proper DNS servers set. Let's call it 10.12.0.10 However, we also have a Windows Server 2003 Domain Controller in our network to which we add our Windows computers (running XP), let's call it 10.12.0.20. I noticed that when I run 'nslookup' on one of the windows machines, it says that the primary DNS is 10.12.0.20. This have not been much of a problem since: The Windows clients are stationary The Windows server in itself point out my real DHCP/DNS, since I can reach everything specified in it However, this turns out to be a problem when we use Laptops. They connect to the domain here and gets a DNS server, but when the user travels or connect the computer from home, we hit a problem. They are connected to their internet, but their DNS is 10.12.0.20 which they can't reach since they're at home and not at the office network. I solved this by removing the register key called "NameServer" with the value 10.12.0.20, but it gets set again whenever they logon to the domain the next time (when they get back to the office). Can I somehow make the computers take whatever DNS server they are handed when connecting to the internet or a home network, instead of always trying to reach the Domain Controller?

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• Windows : Map-a-network-drive to a remote Shared-Folder (on QNAP NAS) using OpenVPN

  - by spelltox

  Provided my lack of networking knowledge, I've been struggling with this issue for quite a few days now : I have a QNAP-TS212 NAS on which i've created a shared-folder (mostly excel files). All the computers in the local network (windows) are able to access it without any problem. Now, i want to access that shared-folder remotely (windows client), so : I enabled OpenVPN (and PPTP) in QNAP admin. Installed OpenVPN on the remote client. Applied the configuration file that the QNAP generated - Configuration (openvpn.ovpn) : client dev tun script-security 3 proto udp remote ***MY_WAN_IP*** 1194 resolv-retry infinite nobind ca ca.crt auth-user-pass reneg-sec 0 cipher AES-128-CBC comp-lzo OpenVPN connect successfully from the remote client. Now, here's my problem : I can ping the NAS (got IP 10.8.0.1) from the remote client, But when i try to map-a-network-drive, i don't see the shared folder or the NAS or any of the other computers in the network... I checked - all computers are in "WORKGROUP" workgroup. I'm probably missing some basic knowledge, So - any help would be greatly appreciated ! Many thanks.

  Read the article

• Running docker in VPC and accessing container from another VPC machine

  - by Bogdan Gaza

  I'm having issues while running docker in AWS VPC. Here is my setup: I've got two machines running in VPC: 10.0.100.150 10.0.100.151 both having an elastic IPs assigned to them, both running in the same internet enabled subnet. Let's say I'm running a web server that serves static files in a container on the 10.0.100.150 machine the container: IP: 172.17.0.2 port 8111 is forwarded on the 8111 port on the machine. I'm trying to access the static files from my local machine (or another non-VPC machine also tried an EC2 instance not running in the VPC) and it work flawlessly. If I try to access the files from the other machine (10.0.100.151) it hangs. I'm using wget to pull the files. Tried to debug it with tcpdump and ngrep and that I have seen is that the request reaches the container. If I ngrep on the host machine I see the requests going in but no response going back. If I ngrep on the container I see the requests going in and the response going back. I've tried multiple iptables setups (with postrouting enabled, with manually forwarding ports etc) but no success. Help in any way - even debugging directions would be much appreciated. Thanks!

  Read the article

• Website has become slower on a VPS, was much fast on a shared host. What's wrong?

  - by Arpit Tambi

  My shared host suspended my website stating system overload, so I moved my website to a VPS which has 4GB RAM. But for some reason the website has become very slow. This is the vmstat output - procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 0 0 3050500 0 0 0 0 0 1 0 0 0 0 100 0 0 Here's the Apache Benchmark output for a STATIC html page I ran on the server itself - Benchmarking www.ask-oracle.com (be patient)...apr_poll: The timeout specified has expired (70007) Total of 20 requests completed Update: Server Config: List item Centos 5.6 4 cores cpu 4 GB RAM LAMP stack with APC Wordpress Only one website It takes almost double time to load now, same website was much fast on shared hosting. I know I need to tweak some settings but have no clue where to start from? I have already tried to optimize apache, mysql etc. Update 2: CPU usage is low, see uptime output: 11:09:02 up 7 days, 21:26, 1 user, load average: 0.09, 0.11, 0.09 Update 3: When I load any webpage, browser shows "Waiting" for a long time and then page loads quickly. So I suspect server can accept only limited connections and holds extra connections in a waiting state. How to check this? Update 4: Following is the output on executing netperf TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to localhost.localdomain (127.0.0.1) port 0 AF_INET Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 16384 10.00 9615.40 [root@ip-118-139-177-244 j3ngn5ri6r01t3]# Here are the Apache MPM settings from httpd.conf, do they look okay? <IfModule worker.c> StartServers 5 MaxClients 100 MinSpareThreads 50 MaxSpareThreads 250 ThreadsPerChild 125 MaxRequestsPerChild 10000 ServerLimit 100 </IfModule>

  Read the article

• What am I doing wrong in my config for MySql?

  - by Knight Hawk3

  When I load my my.conf with the config at the bottom Mysql fails to start and prints no errors. I am running Arch Linux (Updated) with the latest MySQL (5.5) and the latest nginx (Well latest in the repository, Not sure how to check. Only installed it today) I will give you any info you ask for. Thanks for helping! # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/run/mysqld/mysqld.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/run/mysqld/mysqld.sock skip-locking key_buffer = 16K max_allowed_packet = 1M table_cache = 4 sort_buffer_size = 64K read_buffer_size = 256K read_rnd_buffer_size = 256K net_buffer_length = 2K thread_stack = 64K # Don’t listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (using the “enable-named-pipe” option) will render mysqld useless! # #skip-networking server-id = 1 # Uncomment the following if you want to log updates #log-bin=mysql-bin # Uncomment the following if you are NOT using BDB tables skip-bdb # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = /var/lib/mysql/ #innodb_data_file_path = ibdata1:10M:autoextend #innodb_log_group_home_dir = /var/lib/mysql/ #innodb_log_arch_dir = /var/lib/mysql/ # You can set .._buffer_pool_size up to 50 – 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 16M #innodb_additional_mem_pool_size = 2M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 5M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 skip-innodb [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 1M sort_buffer_size = 1M [myisamchk] key_buffer = 1M sort_buffer_size = 1M [mysqlhotcopy] interactive-timeout So what is my silly error?

  Read the article

• Setting up port forwarding for web server

  - by reyjavikvi

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

• Connection refused in ssh tunnel to apache forward proxy setup

  - by arkascha

  I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

  Read the article

• Get Illegal Instruction error when booting Linux in VirtualBox, works fine when booted directly

  - by rkjnsn

  I have a computer on which I am dual booting Windows 7 and Gentoo Linux (both 64-bit). I want to be able to load up my Linux installation in a VM while I am booted into Windows. I have installed VirtualBox and followed the instructions for creating a raw disk VMDK. When I start the VM, Linux starts booting, but then fails with the following error when unlocking my root partition: truecrypt[441] trap invalid opcode ip:373615538e0 sp:3dd0e0dfb60 error:0 in libpixman-1.so.0[373614d6000+8d000] Everything works fine when I boot into Linux directly. What could cause an illegal instruction to be hit in libpixman only when booting in VirtualBox? Update: As a troubleshooting step, I recompiled pixman without "-march", and no longer get an illegal instruction error in that library. (The boot fails in the same spot with the same error in a different library, however.) How can I determine the specific opcode that isn't working in VirtualBox so I can disable it in my CFLAGS without having to disable all CPU-specific optimizations? I am still confused as to why there would be any user-mode instruction that would fail to work in a VM. Is this a known limitation? My CPU is an Intel Core i7 3720QM, and I have hardware virtualization support enabled.

  Read the article

• Network latency and speed of light

  - by James

  This was kinda of covered by the following Is minimum latency fixed by the speed of light? , but i would like to add the follow up a bit. The scenario is as follows; we have two opposing sites one on the West Coast of the US and one in Ireland. The customer is in central Europe, and has requested a latency test. Ireland gives responses of ~65-70ms. However the West Coast guys claim to be faster with a response of 60ms. Now a quick check says that light in fiber would take about 42ms to make the trip to the States and 8.5ms to Ireland. So obviously this is a single hop and does not include routers, switches, firewalls, protocol overhead etc. Would I be right to call BS on their figures? As a final note I tested a ping to Google IP address that was allegedly on the west coast from a site that covered a similar distance and was amazed to get a response time of 20ms. Suggesting ICMP packets that travel twice the speed of light. So A) what am I missing B) Am I right to suspect shenanigans? UPDATE: Guys thanks so far for your help and I have been reading various previous questions on this. About 5 years I had an issue where the hop from the UK to Ireland added 10ms of latency no matter what we did. In the end I moved the servers; So imagine my surprise when I have guys that claim they are 5ms faster with a transatlantic trip. So again should I call BS? Oh and assume both sites are normal mortals that don't have access to Google magical routing, warp dives or flux capacitors. :)

  Read the article

• Prevent nginx from redirecting traffic from https to http when used as a reverse proxy

  - by Chris Pratt

  Here's my abbreviated nginx vhost conf: upstream gunicorn { server 127.0.0.1:8080 fail_timeout=0; } server { listen 80; listen 443 ssl; server_name domain.com ~^.+\.domain\.com$; location / { try_files $uri @proxy; } location @proxy { proxy_pass_header Server; proxy_redirect off; proxy_set_header Host $http_host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto https; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 120; proxy_pass http://gunicorn; } } The same server needs to serve both HTTP and HTTPS, however, when the upstream issues a redirect (for instance, after a form is processed), all HTTPS requests are redirected to HTTP. The only thing I have found that will correct this issue is changing proxy_redirect to the following: proxy_redirect http:// https://; That works wonderfully for requests coming from HTTPS, but if a redirect is issued over HTTP it also redirects that to HTTPS, which is a problem. Out of desperation, I tried: if ($scheme = 'https') { proxy_redirect http:// https://; } But nginx complains that proxy_redirect isn't allowed here. The only other option I can think of is to define the two servers separately and set proxy_redirect only on the SSL one, but then I would have duplicate the rest of the conf (there's a lot in the server directive that I omitted for simplicity sake). I know I could also use an include directive to factor out the redundancy, but I really want to keep just one conf file without any dependencies. So, first, is there something I'm missing that will negate the problem entirely? Or, second, if not, is there any other way (besides including an external file) to factor out the redundant config information so that I can separate out the HTTP and HTTPS versions of the server config?

  Read the article

• Can't ping through default gateway

  - by Andrew G.H.

  I have the following configuration: Routing table on M3 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.3.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 Routing table on M1 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 So basically M3's gateway is M1, and M1's gateway is M2's wireless internet interface. If I ping 8.8.8.8 from M1, everything is ok, replies are received. Pinging from M1 to M3 and viceversa is also possible. I have configured M1 as gateway trafic forwarder using firestarter package and stopped firewall with it. iptables policies are ACCEPT for everything. Problem: I have tried ping-ing ip 8.8.8.8 from M3 but without success. What could be the source of this problem?

  Read the article

• DKIM- Filter No Signature Data

  - by Vineet Sharma

  I have installed DKIM-Filter on Postfix after reading this tutorial http://www.unibia.com/unibianet/systems-networking/how-setup-domainkeys-identified-mail-dkim-postfix-and-ubuntu-server My email now has a DKIM signature but still it is landing in the SPAM folder. Here is the header Received-SPF: neutral (google.com: 69.164.193.167 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=69.164.193.167; Authentication-Results: mx.google.com; spf=neutral (google.com: 69.164.193.167 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected]; dkim=hardfail (test mode) [email protected] Received: from promote.a2labs.in (localhost [127.0.0.1]) by promote.a2labs.in (Postfix) with ESMTPA id 34858530E8 for <[email protected]>; Mon, 28 Feb 2011 12:23:07 +0530 (IST) DKIM-Signature: v=1; a=rsa-sha256; c=simple/simple; d=a2labs.in; s=mail; t=1298875987; bh=bo+H1VYPIHMja2u7i1lnzr4k/j4Pe8iSf79bVw94XpI=; h=To:Subject:Message-ID:Date:From:Reply-To:MIME-Version: Content-Type:Content-Transfer-Encoding; b=nhTdlnUwo0iUJ92ycQzKSRjw 5Pfya0DJcJrAc8Mr2hIv8OLpgzBCzdOMWTGqR5nuUmAzgCGYBhYAM2XZwVxo9JG/iz7 oYKysmNQnskFx0TRyW3UOkDWcfHcPnCL6Y7fGzZWinmsyjsg47k+mKZg/e8jqlwTAMO PYKkt5pBz7SM0= Also my mail.err file shows Feb 28 12:17:03 ivineet dkim-filter[32181]: 1F788530E1: no signature data Feb 28 12:18:02 ivineet dkim-filter[32181]: 432BA530E2: no signature data How to fix it

  Read the article

• ports only available from the outside network

  - by ChrisJ

  This is a counter-intuitive problem for me. I have a new Win 2003 server on a static IP address w.x.y.z. Tomcat 7, PostgreSQL 9.1, and Subversion are installed. All of it appears to be working fine from the server itself. We can also access the Tomcat manager, web applications, and run "svn ls svn://w.x.y.z/" from outside our network. However, when I try from another machine in the office, phpPgAdmin and svn cannot establish connections with the server. http://w.x.y.z:5432/phppgadmin cannot connect. The svn command from above returns: svn: E730061: Unable to connect to a repository at URL 'svn://w.x.y.z/' svn: E730061: Can't connect to host 'w.x.y.z': No connection could be made because the target machine actively refused it. Tomcat manager and the other web apps we have deployed work fine. Netstat -a from the server shows this: Proto Local Address Foreign Address State TCP SERVERNAME:3690 SERVERNAME:0 LISTENING TCP SERVERNAME:5432 SERVERNAME:0 LISTENING Windows Firewall was off, but just in case I also tried to enable it and open ports 3690 (svn) and 5432 (postgres). No change. I don't have access to the router/switch because it just doesn't work that way in Port-au-Prince and our sysadmin is on R&R. Is there anything that might be causing the problem from the server side?

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7.

  Read the article

• Bridging my laptop's wireless and wired adaptors

  - by stacey.richards

  I would like to be able to connect a desktop computer that does not have a wireless adapter to my wireless network. I could just run a network cable from my ADSL/wireless router to the desktop computer but sometimes this is not practical. What I would really like to do is bridge my laptop's wireless and wired adapters in such a way that I can run a network cable from my laptop to a switch and another network cable from the switch to a desktop computer so that the desktop computer can access the Internet through my ADSL/wireless router via my latop: +--------------------+ |ADSL/wireless router| +--------------------+ | +-------------------------+ |laptop's wireless adaptor| | | |laptop's wired adaptor | +-------------------------+ | +------+ |switch| +------+ | +-----------------------+ |desktop's wired adapter| +-----------------------+ A bit of Googling suggests that I can do this by bridging my laptop's wireless and wired adapters. In Windows XP's Network Connections I select both the Local Area Connection and the Wireless Network Connection, right click and select Bridge Connections. From what I gather, this (layer 2?) bridge will examine the MAC address of traffic coming from the wireless network and pass it through to the wired network if it suspects that a network adapter with that MAC address may be on the wired side, and vice-versa. If this is the case, I would assume that when the desktop computer attempts to get an IP address from a DHCP server (which is running on the ADSL/wireless router), it would send a DHCP broadcast packet which would pass through the laptop's bridge to the router and the reply would return through the laptop's bridge back to the desktop. This doesn't happen. With some more Googling I find some instruction how this can be done with Linux. I reboot to Ubuntu 9.10 and type the following: sudo apt-get install bridge-utils sudo brctl addbr br0 sudo brctl addif br0 wlan0 sudo brctl addif br0 eth0 sudo ipconfig wlan0 0.0.0.0 sudo ipconfig eth0 0.0.0.0 Once again, the desktop cannot reach the ADSL/wireless router. I suspect that I'm missing some simple important step. Can anyone shed some light on this for me?

  Read the article

• postfix smtp_fallback_relay for deferred messages to a single domain

  - by EdwardTeach

  I use Postfix to send messages to a mail server outside my organization which frequently rejects/defers my mail. My Postfix server sees that these messages are deferred and tries again, eventually getting through. Final delivery can take up to an hour, which makes my users unhappy. In comparison, mail from my Postfix server to other hosts works normally. I have now found out about a second, unofficial MX for this domain that does not reject/defer mail. This second MX does not appear when doing a DNS MX query for the domain. Therefore, for the problem domain I would like to use this second MX as a fallback. That is: whenever mail is deferred by the primary MX, try again on the unofficial second MX. I see that there is already a postfix configuration "smtp_fallback_relay". However the documentation seems to indicate that I can not restrict usage of the fallback to a single domain. The documentation also doesn't mention deferred message handling. So is there a way to configure a single-domain, deferred-retry fallback host in Postfix? For reference, I am including my postconf output (the host names and ip addresses are fake): alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/etc/postfix/legacy_mailman, ldap:/etc/postfix/ldap-aliases.cf append_dot_mydomain = no biff = no config_directory = /etc/postfix default_destination_concurrency_limit = 2 inet_interfaces = all inet_protocols = all local_destination_concurrency_limit = 2 local_recipient_maps = $alias_maps mailbox_size_limit = 0 mydestination = myhost.my.network, localhost.my.network, localhost, my.network myhostname = myhost.my.network mynetworks = 127.0.0.0/8, [::ffff:127.0.0.0]/104, [::1]/128, 10.10.10.0/24 myorigin = my.network readme_directory = no recipient_delimiter = + relay_domains = $mydestination relayhost = smtp_fallback_relay = the.problem.host smtp_header_checks = smtpd_banner = $myhostname ESMTP $mail_name virtual_alias_maps = hash:/etc/postfix/virtual

  Read the article

• Connecting to my home router web interface from work

  - by Joe

  Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

  Read the article

• How do I secure Sql Server 2008 R2

  - by Mark Tait

  I have both a dedicated and a VPS (from Fasthosts) virtual server - the web sites/applications I run on these, access Sql Server stored on the same web server. Until now, I have logged onto Sql Server on both the deidicated and VPS server, from Sql Server Management Studio - until I noticed in my server application logs, multiple attempts to logon to Sql Server using the 'sa' username, but failed password. So someone/bot is trying hard (repeatedly every couple of hours, for approx 20 attempts during each instance) to log on... so obviously I have to lock down access to Sql Sever remotely. What I have done is gone into Configuration Manager, and in Sql Server Network Configuration - Protocols for Sql2008 and also in Sql Native Client 10.0 Configuration - Client Protocols - I have diabled Named Pipes, TCP/IP (and VIA by default). I have left Shared Memory enabled. I also disabled in Sql Server Services, the Sql Server Browser. Now the only way I can manage the databases on these servers, is by logging on to them via Remote Desktop. Can anyone confirm if this is the correct way of stopping anyone maliciously logging on to Sql Server? (I'm not a DBA or security expert - and there are hundreds of articles advising all different ways - but I was hoping for the experts here to confirm, or otherwise, if what I've done is correct) Thank you, Mark

  Read the article

• iptables rules to allow HTTP traffic to one domain only

  - by Emily

  Hi everyone, I need to configure my machine as to allow HTTP traffic to/from serverfault.com only. All other websites, services ports are not accessible. I came up with these iptables rules: #drop everything iptables -P INPUT DROP iptables -P OUTPUT DROP #Now, allow connection to website serverfault.com on port 80 iptables -A OUTPUT -p tcp -d serverfault.com --dport 80 -j ACCEPT iptables -A INPUT -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT #allow loopback iptables -I INPUT 1 -i lo -j ACCEPT It doesn't work quite well: After I drop everything, and move on to rule 3: iptables -A OUTPUT -p tcp -d serverfault.com --dport 80 -j ACCEPT I get this error: iptables v1.4.4: host/network `serverfault.com' not found Try `iptables -h' or 'iptables --help' for more information. Do you think it is related to DNS? Should I allow it as well? Or should I just put IP addresses in the rules? Do you think what I'm trying to do could be achieved with simpler rules? How? I would appreciate any help or hints on this. Thanks a lot!

  Read the article

• Cisco IOS BVI ACL: Only allow established UDP

  - by George Bailey

  Related: Cisco IOS ACL: Don't permit incoming connections just because they are from port 80 I know we can use the established keyword for TCP.. but what can we do for UDP (short of replacing a Bridge or BVI with a NAT)? Answer I found out what "UDP has no connection" means. DNS uses UDP for example.. named (DNS server) is lisenting on port 53 nslookup (DNS client) starts listening on some random port and sends a packet to port 53 of the server and notes the source port in that packet. nslookup will retry 3 times if necessary. Also the packets are so small that it does not have to worry about them coming in the wrong order. If nslookup receives a response on that port that comes from the servers IP and port then it stops listening. If the server tried to send two responses (for example a response and a response to the retry) then the server would not care if either of them made it because the client has the job to retry. In fact.. unless ICMP 3/3 packet gets through the server would not know about a failure. This is different from TCP where you get connection closed or timed out errors. DNS allows for an easy retry from the client as well as small packets.. so UDP is an excellent choice because it is more efficient. In UDP you would see nslookup sends request named sends answer In TCP you would see nslookup's machine sends SYN named's machine sends SYN-ACK nslookup's machine sends ACK and the request named's machine sends the response That is much more than is necessary for a tiny DNS packet

  Read the article

< Previous Page | 421 422 423 424 425 426 427 428 429 430 431 432  | Next Page >