Search Results

Search found 4304 results on 173 pages for 'bytes'.

Page 43/173 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

• Unable to connect to Wireless after installing Ubuntu 12.10

  - by Moulik

  I am using Asus U56E laptop and after installing Ubuntu 12.10 alongside Windows 8, I am unable to connect to the Wireless. I have been trying to solve this problem since two weeks and couldn't solve it. Please help. Any answer would be appreciated. Here are some command-line results. lspci -v | grep -iA 7 network ubuntu@ubuntu:~$ lspci -v | grep -iA 7 network 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Subsystem: Intel Corporation Centrino Wireless-N + WiMAX 6150 BGN Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at de800000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi lsmod | grep iwlwifi ubuntu@ubuntu:~$ lsmod | grep iwlwifi iwlwifi 386826 0 mac80211 539908 1 iwlwifi cfg80211 206566 2 iwlwifi,mac80211 ubuntu@ubuntu:~$ dmesg | grep iwlwifi [ 57.846261] iwlwifi: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 57.846264] iwlwifi: Copyright(c) 2003-2012 Intel Corporation [ 57.846336] iwlwifi 0000:02:00.0: >pci_resource_len = 0x00002000 [ 57.846338] iwlwifi 0000:02:00.0: >pci_resource_base = ffffc90000c7c000 [ 57.846341] iwlwifi 0000:02:00.0: >HW Revision ID = 0x67 [ 57.846438] iwlwifi 0000:02:00.0: >irq 52 for MSI/MSI-X [ 59.558335] iwlwifi 0000:02:00.0: >loaded firmware version 41.28.5.1 build 33926 [ 59.558514] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUG disabled [ 59.558516] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUGFS enabled [ 59.558517] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 59.558519] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 59.558520] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_P2P disabled [ 59.558522] iwlwifi 0000:02:00.0: >Detected Intel(R) Centrino(R) Wireless-N + WiMAX 6150 BGN, REV=0x84 [ 59.558583] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 59.569083] iwlwifi 0000:02:00.0: >device EEPROM VER=0x557, CALIB=0x6 [ 59.569085] iwlwifi 0000:02:00.0: >Device SKU: 0x150 [ 59.569087] iwlwifi 0000:02:00.0: >Valid Tx ant: 0x1, Valid Rx ant: 0x3 [ 59.569100] iwlwifi 0000:02:00.0: >Tunable channels: 13 802.11bg, 0 802.11a channels [ 70.208469] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.208648] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 [ 70.366319] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.366470] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 sudo lshw -c network ubuntu@ubuntu:~$ sudo lshw -c network *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:84:99:c4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.5.0-17-generic firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 54:04:a6:2b:6a:ef capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) ifconfig ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 54:04:a6:2b:6a:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:176 errors:0 dropped:0 overruns:0 frame:0 TX packets:176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14368 (14.3 KB) TX bytes:14368 (14.3 KB) wlan0 Link encap:Ethernet HWaddr 40:25:c2:84:99:c4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) iwconfig ubuntu@ubuntu:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off iwlist scan ubuntu@ubuntu:~$ iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results nm-tool ubuntu@ubuntu:~$ nm-tool NetworkManager Tool State: disconnected - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 54:04:A6:2B:6A:EF Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: disconnected Default: no HW Address: 40:25:C2:84:99:C4 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points hypeness2: Infra, 00:21:29:DA:08:4F, Freq 2462 MHz, Rate 54 Mb/s, Strength 42 WPA love: Infra, 68:7F:74:17:02:66, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 DIRECT-MwSCX-3400Pamela: Infra, 02:15:99:A3:3F:AC, Freq 2412 MHz, Rate 54 Mb/s, Strength 22 WPA2 router: Infra, 1C:AF:F7:D6:76:F3, Freq 2417 MHz, Rate 54 Mb/s, Strength 20 WPA2 wing: Infra, E8:40:F2:34:E4:F7, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 132LINKSYS: Infra, 00:1A:70:80:1F:E9, Freq 2437 MHz, Rate 54 Mb/s, Strength 57 WEP VMITTAL: Infra, E0:46:9A:3C:F0:C4, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 WEP HP-Print-10-LaserJet 1025: Infra, 7C:E9:D3:7E:F8:10, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 ACNBB: Infra, 00:26:75:22:A6:2F, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 SATKAIVAL: Infra, 00:18:E7:CE:69:A6, Freq 2412 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2 hypeness: Infra, B8:E6:25:24:C3:B1, Freq 2437 MHz, Rate 54 Mb/s, Strength 54 WPA WPA2 CSNetwork: Infra, BC:14:01:58:C5:88, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2 tharma: Infra, BC:14:01:E2:06:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 15 WPA WPA2 Active2.4: Infra, 10:6F:3F:0E:F3:8E, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 ACNBB: Infra, 00:26:75:58:4E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 85 KO: Infra, BC:14:01:2E:AF:A8, Freq 2452 MHz, Rate 54 Mb/s, Strength 22 WPA WPA2 FEAR: Infra, 00:18:4D:C0:BC:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA Pamela: Infra, BC:14:01:52:F6:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 bvrk2: Infra, 78:CD:8E:7B:3C:79, Freq 2457 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 BELL030: Infra, D8:6C:E9:17:AF:09, Freq 2462 MHz, Rate 54 Mb/s, Strength 22 WPA2 Desai: Infra, 00:1D:7E:52:FB:C5, Freq 2437 MHz, Rate 54 Mb/s, Strength 14 WEP Sritharan: Infra, BC:14:01:E5:59:78, Freq 2462 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 PFN: Infra, 00:13:10:8B:CF:45, Freq 2437 MHz, Rate 54 Mb/s, Strength 19 WEP rfkill list all ubuntu@ubuntu:~$ rfkill list all 0: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wimax: WiMAX Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no so these are some more results sudo modprobe -r iwlwifi ubuntu@ubuntu:~$ sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1 ubuntu@ubuntu:~$ sudo modprobe iwlwifi 11n_disable=1 echo "blacklist asus_wmi" | sudo tee -a /etcmodprobe.d/blacklist.conf ubuntu@ubuntu:~$ echo "blacklist asus_wmi" | sudo tee -a /etc/modprobe.d/blacklist.conf blacklist asus_wmi echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf ubuntu@ubuntu:~$ echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi ubuntu@ubuntu:~$ sudo modprobe -rfv iwlwifi rmmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko sudo modprobe -v iwlwifi ubuntu@ubuntu:~$ sudo modprobe -v iwlwifi insmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko 11n_disable=1

  Read the article

• Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

  - by Donal

  I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

  Read the article

• Trying to run Soldier of fortune 2 on ubuntu 12.04 64 using wine 1.4

  - by Fyksen

  Im trying to run SoF 2 multiplayer in ubuntu 12.04. If I run in terminal I get this output: fyksen@fyksen-skole:~/Nedlastinger/SOF2_FULL på gunnar (gunnar)$ wine SoF2MP.exe fixme:thread:NtQueryInformationThread Cannot get kerneltime or usertime of other threads err:seh:setup_exception_record stack overflow 1916 bytes in thread 0009 eip 7bc3e41f esp 01270bb4 stack 0x1270000-0x1271000-0x1a70000 It seems like it's the: "err:seh:setup_exception_record stack overflow 1916 bytes in thread 0009 eip 7bc3e41f esp 01270bb4 stack 0x1270000-0x1271000-0x1a70000" I google it but i couldn't find any solution

  Read the article

• No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

  - by jrosell

  Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

  Read the article

• creating a bootable USB stick on OS X

  - by Rob

  I'm trying to create a bootable USB stick on OS X using http://www.ubuntu.com/download/help/create-a-usb-stick-on-mac-osx When this finishes, I get a message in terminal saying "695+1 records in 695+1 records out 729067520 bytes transferred in 264.563662 secs (2755736 bytes/sec)" But a message pops up saying "The disk you inserted was not readable by this computer" Options are Initialize, Ignore or Eject. What am I doing wrong or omitting. (oh - complete novice)

  Read the article

• w3wp.exe (ASP .Net) eating memory (2 replies)

  Hello, i'm on a VPS with Windows 2003 x64 (IIS 6.0 so) and i have a serious problem with w3wp.exe. It starts from 60 Mb and then grows until the whole avaiable RAM is used. http://img32.imageshack.us/img32/4120/w3wpgraph.png Here's an example image showing w3wp.exe private bytes and Gen 0 Heap size. They seems related, but if I use &quot;.NET CLR Memory/# Bytes in all Heaps &quot; it is much lower than priv...

  Read the article

• To Obtain EPOCH Time Value from a Packed BIT Structure in C [migrated]

  - by xde0037

  This is not a home assignment! We have a binary data file which has following data structure: (It is a 12 byte structure): I need to find out Epoch time value(total time value is packed in 42 bits as described below): Field-1 : Byte 1, Byte 2, + 6 Bits from Byte 3 Time-1 : 2 Bits from Byte 3 + Byte 4 Time-2 : Byte 5, Byte 6, Byte 7, Byte 8 Field-2 : Byte 9, Byte 10, Byte 11, Byte 12 For Field-1 and Field-2 I do not have issue as they can be taken out easily. I need time value in Epoch Time (long) as it has been packed in Bytes 5,6,7,8 and 3 and 4 as follows: (the bit structure for the time value is as follows): Bytes 5 to 8 (32 bit word) Packs time value bits from 0 thru 31 (byte 5 has 0 to 7 bits, byte 6 has 8 to 15, byte 7 has 16 to 23, byte 8 has 24 to 31). the remaining 10 bits of time value are packed in Bytes 3 and byte 4 as follows: byte 3 has 2 bits:32 and 33, and Byte 4 has remaining bits : 34 to 41. So total bits for time value is 42 bits, packed as above. I need to compute epoch value coming out of these 42 bits. How do I do it? I have done something like this but not sure it gives me correct value: typedef struct P_HEADER { unsigned int tmuNumber : 21; unsigned int time1 : 10; // Bits 6,7 from Byte-3 + 8 bits from Byte-4 unsigned int time2 : 32; // 32 bits: Bytes 5,6,7,8 unsigned int traceKey : 32; } __attribute__((__packed__)) P_HEADER; Then in the code : P_HEADER *header1; //get input string in hexa,etc..etc.. //parse the input with the header as : header1 = (P_HEADER *)inputBuf; // then print the header1->time1, header1->time2 .... long ttime = header1->time1|header1->time2; //?? is this the way to get values out? Any hint tip will be appreciated. Environment is : gcc 4.1, Linux Thanks in advance.

  Read the article

• How many bits for sequence number using Go-Back-N protocol.

  - by Mike

  Hi Everyone, I'm a regular over at Stack Overflow (Software developer) that is trying to get through a networking course. I got a homework problem I'd like to have a sanity check on. Here is what I got. Q: A 3000-km-long T1 trunk is used to transmit 64-byte frames using Go-Back-N protocol. If the propagation speed is 6 microseconds/km, how many bits should the sequence numbers be? My Answer: For this questions what we need to do is lay the base knowledge. What we are trying to find is the size of the largest sequence number we should us using Go-Back-N. To figure this out we need to figure out how many packets can fit into our link at a time and then subtract one from that number. This will ensure that we never have two packets with the same sequence number at the same time in the link. Length of link: 3,000km Speed: 6 microseconds / km Frame size: 64 bytes T1 transmission speed: 1544kb/s (http://ckp.made-it.com/t1234.html) Propagation time = 6 microseconds / km * 3000 km = 18,000 microseconds (18ms). Convert 1544kb to bytes = 1544 * 1024 = 1581056 bytes Transmission time = 64 bytes / 1581056bytes / second = 0.000040479 seconds (0.4ms) So then if we take the 18ms propagation time and divide it by the 0.4ms transmission time we will see that we are going to be able to stuff ( 18 / 0.4) 45 packets into the link at a time. That means that our sequence number should be 2 ^ 45 bits long! Am I going in the right direction with this? Thanks, Mike

  Read the article

• Several IPs for my VPS

  - by Serafim

  I bought vps on santrex.net but can't receive any reply from support. My Problem: I have 5 ip but it pings only 1!!! I can't setup DNS because I need 2 ip minimum . Could you help me to activate other my IPs? root@spnova:~# ifconfig eth0 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.100 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:163342 errors:0 dropped:0 overruns:0 frame:0 TX packets:13585 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32862185 (32.8 MB) TX bytes:15189036 (15.1 MB) eth0:0 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.101 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:1 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.102 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:2 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.103 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:3 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.104 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:11885 errors:0 dropped:0 overruns:0 frame:0 TX packets:11885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8124693 (8.1 MB) TX bytes:8124693 (8.1 MB) root@spnova:~# nano /etc/network/interfaces # Auto generated eth0 interfaces auto eth0 lo iface eth0 inet static address 188.72.240.100 netmask 255.255.255.0 up route add -net 188.72.225.0 netmask 255.255.255.0 dev eth0 up route add default gw 188.72.225.1 iface lo inet loopback auto eth0:0 iface eth0:0 inet static address 188.72.240.101 netmask 255.255.255.0 auto eth0:1 iface eth0:1 inet static address 188.72.240.102 netmask 255.255.255.0 auto eth0:2 iface eth0:2 inet static address 188.72.240.103 netmask 255.255.255.0 auto eth0:3 iface eth0:3 inet static address 188.72.240.104 netmask 255.255.255.0

  Read the article

• Can I upgrade the CPU in my Lenovo 3000 N100 laptop?

  - by Pavel

  I've got an Intel Core Duo T2300 in my laptop (Lenovo 3000 N100, 0768-49G). Here is what I could find out about it: $ sudo dmidecode # dmidecode 2.11 SMBIOS 2.4 present. 42 structures occupying 1436 bytes. Table at 0x000DC010. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: LENOVO Version: 61ET37WW Release Date: 06/04/07 Address: 0xE6B70 [...] Handle 0x0002, DMI type 2, 8 bytes Base Board Information Manufacturer: LENOVO Product Name: CAPELL VALLEY(NAPA) CRB [...] Handle 0x0004, DMI type 4, 35 bytes Processor Information Socket Designation: U2E1 Type: Central Processor Family: Other Manufacturer: Intel ID: E8 06 00 00 FF FB E9 BF Version: Genuine Intel(R) CPU T2300 @ 1.66GHz Voltage: 3.3 V External Clock: 166 MHz Max Speed: 2048 MHz Current Speed: 1600 MHz Status: Populated, Enabled Upgrade: ZIF Socket L1 Cache Handle: 0x0005 L2 Cache Handle: 0x0006 L3 Cache Handle: Not Provided Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified $ cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 14 model name : Genuine Intel(R) CPU T2300 @ 1.66GHz stepping : 8 microcode : 0x39 cpu MHz : 1000.000 cache size : 2048 KB I believe the chipset is "Mobile Intel 945GM Express", but I don't know how to verify it on a Linux system. I'm not sure about the socket, but Intel claims "Sockets Supported: PBGA479, PPGA478". Now, I'd like to upgrade to the fastest compatible CPU available, but I'm a bit lost in all the details. Can you guys help me out with a couple of questions, please? What CPUs can I choose from? (I think it's only the Core2Duo line, but it should be enough for an upgrade) Can I use a 64-bit CPU? Can I use a CPU with a higher FSB than 667 MHz? Do I have to worry about additional cooling, or is it enough to check for similar voltage/TDP values? Thank you!

  Read the article

• Browser sends http request with RANGE

  - by nute

  I have a local testing environment in a Fedora virtual machine. Strangely, resources (css and js files) don't seem to work. Looking at Firebug, I see that the browser sends the HTTP request with "Range bytes=0-". The server responds with either an empty 200OK or an empty 206 Partial Content. Here is an example: Response Headers Date Mon, 23 Nov 2009 23:33:26 GMT Server Apache/2.2.13 (Fedora) Last-Modified Thu, 19 Nov 2009 22:58:55 GMT Etag "18-3aec-478c14dbee138" Accept-Ranges bytes Content-Length 15084 Content-Range bytes 0-15083/15084 Connection close Content-Type text/css Request Headers Host fedora.test User-Agent Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091105 Fedora/3.5.5-1.fc11 Firefox/3.5.5 Accept text/css,*/*;q=0.1 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 300 Connection keep-alive Referer http://fedora.test/pictures/ Cookie __utma=26341546.1613992749.1258504422.1258569125.1258752550.4; __utmz=26341546.1258504422.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); PHPSESSID=tqf8jfmc77qihe97rl4tmhq685 Range bytes=0- If-Range "18-3aec-478c14dbee138" I don't know if the browser is sending the wrong request, or if it's the server that is doing this. Request made to the outside (such as google analytics) are working fine. This is running in Fedora 11 in VirtualBox. Apache. PHP. The files are being served through the "shared folders" feature of VirtualBox (could it be related?). No error logs could help me.

  Read the article

• How do I tell ubuntu to send traffic to a single IP through eth6?

  - by flashnode

  I want to ensure that all IP traffic going to 172.16.60.62 uses eth6. Please provide complete commands because my linux-fu is rusty. The host is running Ubuntu Precise 12.04 user@host:~$ ifconfig eth3 eth3 Link encap:Ethernet HWaddr 00:e0:81:72:fe:c9 inet addr:172.16.60.122 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe72:fec9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:128500 errors:0 dropped:0 overruns:0 frame:0 TX packets:29082 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67524823 (67.5 MB) TX bytes:2217634 (2.2 MB) Interrupt:71 Base address:0x6000 user@host:~$ ifconfig eth6 eth6 Link encap:Ethernet HWaddr 00:60:dd:47:81:35 inet addr:172.16.60.61 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:8135/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:109610 errors:0 dropped:0 overruns:0 frame:0 TX packets:109388 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10785630 (10.7 MB) TX bytes:10754350 (10.7 MB) Interrupt:70 user@host:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.60.1 0.0.0.0 UG 0 0 0 eth3 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth3

  Read the article

• special case ssh connection lag

  - by Hersheezy

  Setup We have a DMZ and LAN in our office that are connected to the outside with the following setup: +------+ | |------> LAN (normal office router) |Modem | | |------> DMZ (a single machine) +------+ Our internet account is with Comcast and we have 5 status IPs, one of which points to the single machine in the DMZ. Problem ssh connections initiated ANYWHERE EXCEPT the office LAN are really fast. However, from the LAN, there is about a 5 second delay. WTF?? Extra info The DMZ machine is debian 5. Executing a wget to the DMZ has no lag. When executing the following, everything up to HERE IS WHERE THE LAG IS INCURRED executes immediately. ssh -vvvv [email protected] ... debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/shopkins/.ssh/id_rsa (0x22440830) debug2: key: /home/shopkins/.ssh/identity ((nil)) debug2: key: /home/shopkins/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127` HERE IS WHERE THE LAG IS INCURRED debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /home/shopkins/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/shopkins/.ssh/identity debug3: no such identity: /home/shopkins/.ssh/identity debug1: Trying private key: /home/shopkins/.ssh/id_dsa debug3: no such identity: /home/shopkins/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password:

  Read the article

• Upgrading PEAR from 1.9.0 to 1.9.1 fails

  - by Skelton

  Hi All, I'm willing to install phpunit 5.3 with MAMP 1.9 and there for I need to upgrade PEAR to version 1.9.1. The current version installed is 1.9.0. When I try the to upgrade I get the following: sudo pear channel-update pear.php.net sudo pear upgrade pear Could not get contents of package "/Applications/MAMP/bin/php5.3/bin/pear". Invalid tgz file. upgrade failed When I force the upgrade It still doesn't work: sudo pear upgrade --force PEAR downloading PEAR-1.9.1.tgz ... Starting to download PEAR-1.9.1.tgz (293,587 bytes) .............................................................done: 293,587 bytes upgrade ok: channel://pear.php.net/PEAR-1.9.1 PEAR: Optional feature webinstaller available (PEAR's web-based installer) PEAR: Optional feature gtkinstaller available (PEAR's PHP-GTK-based installer) PEAR: Optional feature gtk2installer available (PEAR's PHP-GTK2-based installer) PEAR: To install optional features use "pear install pear/PEAR#featurename" sudo pear -V PEAR Version: 1.9.0 As bindbn suggested: sudo pear install --offline /Users/tom/Downloads/PEAR-1.9.1.tgz Ignoring installed package pear/PEAR Nothing to install sudo pear upgrade --force --alldeps PEAR downloading PEAR-1.9.1.tgz ... Starting to download PEAR-1.9.1.tgz (293,587 bytes) .............................................................done: 293,587 bytes upgrade ok: channel://pear.php.net/PEAR-1.9.1 PEAR: Optional feature webinstaller available (PEAR's web-based installer) PEAR: Optional feature gtkinstaller available (PEAR's PHP-GTK-based installer) PEAR: Optional feature gtk2installer available (PEAR's PHP-GTK2-based installer) PEAR: To install optional features use "pear install pear/PEAR#featurename" pear -V PEAR Version: 1.9.0 I hope someone can figure this out! Thanks!

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Why can't I route to some sites from my MacBook Pro that I can see from my iPad?

  - by Robert Atkins

  I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

  Read the article

• Windows 7 machine, can't connect remotely until after ping

  - by rjohnston

  I have a Windows 7 (Home Premium) machine that doubles as a media centre and subversion server. There's a couple of problems with this setup, when connecting to the server from an XP (SP3) machine: Firstly, the machine won't respond to it's machine name until after it's IP address has been pinged. Here's an example: Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\Rob>ping damascus Ping request could not find host damascus. Please check the name and try again. C:\Documents and Settings\Rob>ping 192.168.1.17 Pinging 192.168.1.17 with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time=2ms TTL=128 ... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 2ms, Average = 1ms C:\Documents and Settings\Rob>ping damascus Pinging damascus [192.168.1.17] with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time<1ms TTL=128 .... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 1ms, Average = 0ms C:\Documents and Settings\Rob> Likewise, subversion commands with either the machine name or IP address will fail until the machine's IP address is pinged. Occasionally, the machine won't respond to pings on it's IP address, it'll just come back with "Request timed out". The svn server is VisualSVN, if that helps... Any ideas?

  Read the article

• Passwordless SSH not working - keys copied and permissions set

  - by Comcar

  I know this question has been asked, but I'm certain I've done what all the other answers suggest. Machine A: used keygen -t rsa to create id_rsa.pub in ~/.ssh/ copied Machine A's id_rsa.pub to Machine B user's home directory Made the file permissions of id_rsa.pub 600 Machine B added Machine A's pub key to authorised_keys and authorised_keys2: cat ~/id_rsa.pub ~/.ssh/authorised_keys2 made the file permissions of id_rsa.pub 600 I've also ensured both the .ssh directories have the permission 700 on both machine A and B. If I try to login to machine B from machine A, I get asked for the password, not the ssh pass phrase. I've got the root users on both machines to talk to each other using password-less ssh, but I can't get a normal user to do it. Do the user names have to be the same on both sides? Or is there some setting else where I've missed. Machine A is a Ubuntu 10.04 virtual machine running inside VirtualBox on a Windows 7 PC, Machine B is a dedicated Ubuntu 9.10 server UPDATE : I've run ssh with the option -vvv, which provides many many lines of output, but this is the last few commands: debug3: check_host_in_hostfile: filename /home/pete/.ssh/known_hosts debug3: check_host_in_hostfile: match line 1 debug1: Host '192.168.1.19' is known and matches the RSA host key. debug1: Found key in /home/pete/.ssh/known_hosts:1 debug2: bits set: 504/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/pete/.ssh/identity ((nil)) debug2: key: /home/pete/.ssh/id_rsa (0x7ffe1baab9d0) debug2: key: /home/pete/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127 debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/pete/.ssh/identity debug3: no such identity: /home/pete/.ssh/identity debug1: Offering public key: /home/pete/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/pete/.ssh/id_dsa debug3: no such identity: /home/pete/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password

  Read the article

• How can I find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Is this a File Header / Magic Number?

  - by Hammer Bro.

  I've got 120,000 files (way more, actually; this is just an arbitrary subset) of an unknown type. Linux file does not identify them (not that they're necessarily Linux files), nor do any other methods I've tried. There are only two hints about them that I currently have. One is that I suspect some compression is employed -- I have metadata that claims the file sizes are always some amount larger than what I observe. The other is that in 100,000 of these files, the first 16 bytes are always: ff ee ee dd 00 00 00 00 01 00 00 00 00 00 00 00 That really looks like a file header/magic number to me, but I just can't place it. Does anyone know what kind of files this would indicate? Alternatively, can anyone convince me that these suspiciously common bytes certainly do not indicate a specific file type? UPDATE I don't know the exact reverse-engineering details, but most of the files in our case are zips after the first 29(? or so) bytes are ignored. So in practice the problem is solved (we know how to process the files) but in theory the question is still unanswered -- I don't know which application routinely prepends about 29 bytes to its zips. [I'm not sure if I should leave the question open or not at this point.]

  Read the article

• BackupPC - why does it use rsync --sender --server ... ?

  - by Jakobud

  I'm in the process of experimenting with BackupPC on a CentOS 5.5 server. I have everything pretty much setup with default values. I tried setting up a basic backup for a host's /www directory. The backup fails with the following errors: full backup started for directory /www Running: /usr/bin/ssh -q -x -l root target /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Xfer PIDs are now 30395 Read EOF: Connection reset by peer Tried again: got 0 bytes Done: 0 files, 0 bytes Got fatal error during xfer (Unable to read 4 bytes) Backup aborted (Unable to read 4 bytes) Not saving this as a partial backup since it has fewer files than the prior one (got 0 and 0 files versus 0) First of all, yes I have my ssh keys setup to allow me to ssh to the target server without requiring a password. In the process of troubleshooting, I tried the above ssh command directly from the command line, and it hangs. Looking at the end of the debug messages for SSH I get: debug1: Sending subsystem: /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Request for subsystem '/usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/' failed on channel 0 Next I started looking at the rsync flags. I did not recognize --server and --sender. Looking at the rsync man pages, sure enough, I don't see anything about --server or --sender in there. What are those in there for? Looking at the BackupPC config I have this: RsyncClientPath = /usr/bin/rsync RsyncClientCmd = $sshPath -q -x -l root $host $rsyncPath $argList+ And for the arguments, I have the following listed: --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive Notice there is no --server, --sender or --ignore-times. Why are these things getting added in? Is this part of the problem?

  Read the article

• Gnome 3 gdm fails to start after preupgrade from fedora 14 to 15

  - by digital illusion

  I'm not able to boot fedora 15 in runlevel 5. After all services start, when the login screen should appear, gdm just show a mouse waiting cursor and keeps restarting itself. From /var/log/gdm/\:0-greeter.log Gtk-Message: Failed to load module "pk-gtk-module" /usr/bin/gnome-session: symbol lookup error: /usr/lib/gtk-3.0/modules/libatk-bridge.so: undefined symbol: atk_plug_get_type /usr/libexec/gnome-setting-daemon: symbol lookup error: /usr/lib/gtk-3.0modules/libatk-bridge.so: undefined symbol: atk_plug_get_type Where should atk_plug_get_type be defined? Edit: Here a better description of the error (system-config-network-gui:2643): Gnome-WARNING **: Accessibility: failed to find module 'libgail-gnome' which is needed to make this application accessible /usr/bin/python: symbol lookup error: /usr/lib/gtk-2.0/modules/libatk-bridge.so: undefined symbol: atk_plug_get_type Why there are still references to gtk2? Did preupgrade fail? Attaching upgrade log... it seems gdm was not added, but it is present in the users and groups list. May 26 11:25:52 sysimage sendmail[1076]: alias database /etc/aliases rebuilt by root May 26 11:25:52 sysimage sendmail[1076]: /etc/aliases: 77 aliases, longest 23 bytes, 795 bytes total May 26 11:46:09 sysimage useradd[1793]: failed adding user 'dbus', data deleted May 26 11:53:37 sysimage systemd-machine-id-setup[2443]: Initializing machine ID from D-Bus machine ID. May 26 11:55:28 sysimage useradd[2835]: failed adding user 'apache', data deleted May 26 11:55:38 sysimage useradd[2842]: failed adding user 'haldaemon', data deleted May 26 11:55:43 sysimage useradd[2848]: failed adding user 'smolt', data deleted May 26 11:57:32 sysimage sendmail[3032]: alias database /etc/aliases rebuilt by root May 26 11:57:32 sysimage sendmail[3032]: /etc/aliases: 77 aliases, longest 23 bytes, 795 bytes total May 26 11:57:46 sysimage groupadd[3066]: group added to /etc/group: name=cgred, GID=482 May 26 11:57:47 sysimage groupadd[3066]: group added to /etc/gshadow: name=cgred May 26 11:57:47 sysimage groupadd[3066]: new group: name=cgred, GID=482 May 26 11:58:42 sysimage useradd[3086]: failed adding user 'ntp', data deleted May 26 12:00:13 sysimage dbus: avc: received policyload notice (seqno=2) May 26 12:15:08 sysimage useradd[4950]: failed adding user 'gdm', data deleted May 26 12:24:39 sysimage dbus: avc: received policyload notice (seqno=3) May 26 12:25:24 sysimage useradd[5522]: failed adding user 'mysql', data deleted May 26 12:25:37 sysimage useradd[5533]: failed adding user 'rpcuser', data deleted May 26 12:26:31 sysimage useradd[5592]: failed adding user 'tcpdump', data deleted Any suggestions before I revert installation to F14?

  Read the article

• Forcing a particular SSL protocol for an nginx proxying server

  - by vitch

  I am developing an application against a remote https web service. While developing I need to proxy requests from my local development server (running nginx on ubuntu) to the remote https web server. Here is the relevant nginx config: server { server_name project.dev; listen 443; ssl on; ssl_certificate /etc/nginx/ssl/server.crt; ssl_certificate_key /etc/nginx/ssl/server.key; location / { proxy_pass https://remote.server.com; proxy_set_header Host remote.server.com; proxy_redirect off; } } The problem is that the remote HTTPS server can only accept connections over SSLv3 as can be seen from the following openssl calls. Not working: $ openssl s_client -connect remote.server.com:443 CONNECTED(00000003) 139849073899168:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:177: --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 226 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- Working: $ openssl s_client -connect remote.server.com:443 -ssl3 CONNECTED(00000003) <snip> --- SSL handshake has read 1562 bytes and written 359 bytes --- New, TLSv1/SSLv3, Cipher is RC4-SHA Server public key is 1024 bit Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE SSL-Session: Protocol : SSLv3 Cipher : RC4-SHA <snip> With the current setup my nginx proxy gives a 502 Bad Gateway when I connect to it in a browser. Enabling debug in the error log I can see the message: [info] 1451#0: *16 peer closed connection in SSL handshake while SSL handshaking to upstream. I tried adding ssl_protocols SSLv3; to the nginx configuration but that didn't help. Does anyone know how I can set this up to work correctly?

  Read the article

• Why can't I route to some sites from my MacBook Pro that I can see from my iPad? [closed]

  - by Robert Atkins

  I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

  Read the article

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >