Search Results

Search found 20447 results on 818 pages for 'f5 big ip'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 43/818 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

  • There's IP but can't reach gateway

    - by icky
    I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

    Read the article

  • How ISP or dns server find the nameserevr [on hold]

    - by IT researcher
    I saw some articles about how DNS propagation happens.I know that ISP or DNS server(such as google public dns) cache the ip address of website which it uses to convert domain name to ip address. But my doubt is from where these ISP or dns serevr know which nameserver to go for particular domain name. for example a domain.com has two name servers ns1.domain.com and ns2.domain.com. But how the ISP server or dns server know that it uses these name server and i have to send request to this name server.So where does this record mainatined?

    Read the article

  • Distributed development staff needing a common IP range

    - by bakasan
    I work on a development staff that is geographically distributed, mostly all throughout the state of CA, but several key members also must travel frequently. We rely quite heavily on a 3rd party provider API for a great deal of our subsystems (can't get into who it is or what they do). The 3rd party however is quite stringent on network access and have no notion of a development sandbox. Access is restricted to 2, 3 IP numbers and that's about it. Once we account for our production servers, that leaves us with an IP or two to spare for our dev team--which is still problematic as people's home IP changes, people travel, we have more than 2 devs, etc. Wide IP blocks are not permitted by the 3rd party. Nor will they allow dynamic DNS type services. There is no simple console to swap IPs on the fly either (e.g. if a dev's IP at home changes or they are on the road). As none of us are deep network experts, I'm wondering what our viable options are? Are there such things as 3rd party hosts to VPNs? Generally I think of a VPN as a mechanism to gain access to a home office, but the notion would be a 3rd party VPN that we'd all connect to and we'd register this as an IP origin w/ our 3rd party. We've considered using Amazon EC2 to effectively host a dev environment for each dev and using that to connect. Amazon only gives you so many static IPs however (I believe 5?) so this would only be a stop gap solution until our team size out strips our IP count at Amazon. Those were the only viable thoughts that I had, but again, I'm far from a networking guy. Tried searching for similar threads, but I'm not even sure I know the right vernacular to look around for.

    Read the article

  • Help with algorithmic complexity in custom merge sort implementation

    - by bitcycle
    I've got an implementation of the merge sort in C++ using a custom doubly linked list. I'm coming up with a big O complexity of n^2, based on the merge_sort() slice operation. But, from what I've read, this algorithm should be n*log(n), where the log has a base of two. Can someone help me determine if I'm just determining the complexity incorrectly, or if the implementation can/should be improved to achieve n*log(n) complexity? If you would like some background on my goals for this project, see my blog. I've added comments in the code outlining what I understand the complexity of each method to be. Clarification - I'm focusing on the C++ implementation with this question. I've got another implementation written in Python, but that was something that was added in addition to my original goal(s).

    Read the article

  • Which IP should I use for my nameserver

    - by Luke Bream
    Sorry to ask whats probably very obvious question. I have just got a new server that is fantastically cheap but unfortunatly doesnt come with any technical support and Im very out of my depth ! My hosting company has provided the following information... Below you will find your additional IP addresses added to the server 5.9.36.51 Please note that you can use the subnet only for this server. IP: 5.9.225.64 /27 Mask: 255.255.255.224 Broadcast: 5.9.225.95 Useable IP addresses: 5.9.225.65 to 5.9.225.94 It has cPanel with WHM and im going through the setup... I have a number of questions... my domian is purchased from godaddy and I want to use it as the name server. Question 1: Which IP or IP's do I enter into the godaddy interface for ns1.mydomian.com ns2.mydomain.com Question 2: In the WHM nameserver setup what do I enter for... Please enter an IP address for each of your nameservers. ns1.mydomain.com ?????? ns2.mydomain.com ?????? Add "A Entries" for Hostname IP for Entry: ????????? Thanks for aany help you can give Luke

    Read the article

  • Possible to IPSec VPN Tunnel Public IP Addresses?

    - by caleban
    A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

    Read the article

  • pptpd-logwtmp.so config wrong ip address

    - by rgc
    i have setup a pptp vpn on ubuntu 10.04, and i config local ip address , remote ip address as following: local IP address 10.0.30.100 remote IP address 192.168.13.100 after i use windows to connect to vpn server in windows , i only could send packets, can not receive any packets. i also check the pptp log in ubuntu server, and find this strange thing rcvd [IPCP ConfAck id=0x1 <compress VJ 0f 01> <addr 10.0.30.100>] rcvd [IPCP ConfReq id=0x2 <compress VJ 0f 01> <addr 192.168.13.100> <ms-dns1 202.119.32.6> <ms-dns2 202.119.32.12>] sent [IPCP ConfAck id=0x2 <compress VJ 0f 01> <addr 192.168.13.100> <ms-dns1 202.119.32.6> <ms-dns2 202.119.32.12>] Cannot determine ethernet address for proxy ARP local IP address 10.0.30.100 remote IP address 192.168.13.100 pptpd-logwtmp.so ip-up ppp0 **172.25.146.174** i did not set 172.25.146.174, it should be 192.168.13.100, can anyone tell me what should i do to fix this problem?

    Read the article

  • Domain names timing out after VPS IP change

    - by Fourjays
    I rent a CentOS 5 VPS from a UK-based provider, with DirectAdmin also installed. On Thursday night, they carried out planned maintenance to changed the two IPs I had been assigned to two new ones. On Friday, after the change had taken place, I updated my domain name records to reflect the IP change. Since then, all of the domains pointing to the VPS are timing out. Additionally, DirectAdmin was also not responding, but was was resolved by running the ipswap scripts as found in the DirectAdmin knowledgebase. It did not fix my domains though. I have contacted the VPS provider but I have been waiting for a response for some time now. I have checked again, and again, and all the IPs referenced in DirectAdmin are correct. If I go to the server IP in my browser it responds with "Apache is functioning normally." Email accounts on the server are also functioning correctly. But if I access a domain itself, it times out. Running a ping and a DNS look-up, I can confirm the nameserver IPs are correct. If I run a trace route it reaches an IP that is similar to my VPS IPs (last 2 blocks are different) before timing out (it never shows my server IP). I am relatively new to VPS management so don't have a vast wealth of experience with troubleshooting problems on them. I have checked all of the httpd configuration files, which don't seem to have any IP references in them at all. Looking in the Apache error logs, what errors there are do not coincide with times I have tried to access the site. Is this issue at my provider's end? Is there anything else I can check or test, to rule out post-IP-change problems with my server configuration? It was all running fine prior to the IP change.

    Read the article

  • Possible to IPSec VPN Tunnel Public IP Addresses?

    - by caleban
    A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

    Read the article

  • IP queue buffer

    - by summerbulb
    I seem to have an issue with IP queue. I have a linux machine that I am using to run some experiments. The linux machine is configured to be a router, having two NICs, connecting two other computers, and managing their network traffic. All incoming packages are captured, using iptables, and analyzed by a C application. The application analyzing the packets has a built-in delay, as part of the experiment. So I have one very fast computer sending packets through my linux-router and a (relatively) slow linux-router that analyses and deals with the packets, one by one. This situation leads to the fact that when I fire up a sender application on one of the computers connected to the linux-router, my IP queue on the linux-router gets filled up (almost) instantaneously. The IP queue's max length is currently set to 1024, and if it overflows, the packets are dropped. This is expected and i'm OK with it. But, (and this is where it gets interesting), every now and then I get the following error: "Failed to receive netlink message: No buffer space available" At start, I thought this was due to the IP queue overflow, but after some analysis i found that sometimes I get the error even if the IP queue buffer did not overflow, and sometime I DON'T get the message even though the buffer DID overflow. When I run > cat /proc/net/ip_queue, I get the following table (also used to monitor the IP queue overflow): Peer PID : 27389 Copy mode : 2 Copy range : 65535 Queue length : 0 Queue max. length : 1024 Queue dropped : 1166875 Netlink dropped : 2916 Looking at the last two values, Queue dropped seems to refer to packets that did not manage to get into the IP queue because the buffer was full. I can see this value rise as I bombard the linux-router. Netlink dropped ( as it's name implies :) ) seems to have to do with the error i'm getting. I did my best to search for material on this error, but wasn't able to find anything that seemed to point me in the required direction. Bottom line: Why am I getting this error and what can I do to avoid it?

    Read the article

  • Getting a domain sub-directory url for a new server

    - by Xianlin
    I have an web application server running tomcat and i need to publish my APIs to internet users. However I don't have a domain name for this server and I can only put the ip address of this server (e.g. 145.XXX.XXX.XXX) to point out where my API xml files are located. I have another web server running with a domain name "http://www.webserver.com" registered on the internet and I want to make use of its domain name to server my web application server API xml files location. How can I do that? using "www.webserver.com/api" or using "api.webserver.com"? which is better? Also I wonder if I want to publish a "rstp://145.XXX.XXX.XXX" web link for video streaming purpose, can I use "rstp://www.webserver.com/api" to replace it and how to do it? I always thought the url contain domain sub-directory name cannot point to another IP address, it only can point to another folder location on the webserver itself.

    Read the article

  • A record point not working

    - by Peter
    I'm trying to do an A record point to transfer the hosting of a domain from one provider to another. I don't want to change the nameservers as this will result in emails going down. The output when I dig for the domain shows the correct IP (78.46.63.87) for the new host. I know A records can take a while to propagate but Its been over 36hrs now and I still keep getting this error(below) when I try to pull the domain through as an addon domain via Cpanel on the new host. Are the old nameservers conflicting with the A record point? here's the error: Using nameservers with the following IPs: 208.80.125.4,208.80.126.4,208.80.124.4,208.94.148.4 Sorry, the domain is already pointed to an IP address that does not appear to use DNS servers associated with this server. Please transfer the domain to this servers nameservers or have your administrator add one of its nameservers to /etc/ips.remotedns and make the proper A entries on that remote nameserver.

    Read the article

  • IP Masquerade and forwarding

    - by poelinca
    Hi all , i got a dedicated server running ubuntu server 10.10 with 3 ip adresses on the same eth card ( example: eth0 192.168.0.1 , eth0:0 188.78.45.0 , eth0:1 ... ) with a 3 virtual machines running ( virtualization technologi used is lxc but i don't think this matters too much ) . Now i need to redirect all ports opened ( using ufw to close/open ports ) from the ip 188.78.54.0 ( eth0:0 ) to a virtual machine ip ( let's say for example 192.168.2.3 ) , all requests made by a virtual machine should be redirected back to the virtual machine that made the request ( in this example 192.168.2.3 ) . Lets say the second vm has the ip 192.168.2.4 now i need to redirect all opened ports to from eth0:1 to this ip and viceversa . And so on and so on , what are the iptables/ufw rules to get this done ? and where to save them ( witch config file ) so they stay the same after reboot . In a few words redirect all requests comming from/to eth0:0 to a certan ip , all requests comming from/to eth0:1 to another ip ... Remember i'm saying all ports opened becouse they might be dynamicly changed . p.s. please excuse my bad english

    Read the article

  • iptables, forward traffic for ip not active on the host itself

    - by gucki
    I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

    Read the article

  • How does Google store search trends in backend?

    - by Achshar
    Google trends shows what query has been searched how many times and some other properties of the said query. But how is this data stored in a database? Storing a new row for every search does not seem right. They also tell the query on a time graph, so they must have some way to look for individual searches made by users, but the number of queries they get every day, it does not feel right that they would store every search in a database row along with a time-stamp. This does not apply to just Google trends or Google in general but any other big site that gets awful number of queries and then has tools to see them in depth. I am not an expert on this but I am interested to know some high level structure of how things work behind the scenes.

    Read the article

  • iptables not allowing mysql connections to aliased ips?

    - by Curtis
    I have a fairly simple iptables firewall on a server that provides MySQL services, but iptables seems to be giving me very inconsistent results. The default policy on the script is as follows: iptables -P INPUT DROP I can then make MySQL public with the following rule: iptables -A INPUT -p tcp --dport 3306 -j ACCEPT With this rule in place, I can connect to MySQL from any source IP to any destination IP on the server without a problem. However, when I try to restrict access to just three IPs by replacing the above line with the following, I run into trouble (xxx=masked octect): iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.XXX.XXX.184 -j ACCEPT iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.XXX.XXX.196 -j ACCEPT iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.XXX.XXX.251 -j ACCEPT Once the above rules are in place, the following happens: I can connect to the MySQL server from the .184, .196 and .251 hosts just fine as long as am connecting to the MySQL server using it's default IP address or an IP alias in the same subnet as the default IP address. I am unable to connect to MySQL using IP aliases that are assigned to the server from a different subnet than the server's default IP when I'm coming from the .184 or .196 hosts, but .251 works just fine. From the .184 or .196 hosts, a telnet attempt just hangs... # telnet 209.xxx.xxx.22 3306 Trying 209.xxx.xxx.22... If I remove the .251 line (making .196 the last rule added), the .196 host still can not connect to MySQL using IP aliases (so it's not the order of the rules that is causing the inconsistent behavior). I know, this particular test was silly as it shouldn't matter what order these three rules are added in, but I figured someone might ask. If I switch back to the "public" rule, all hosts can connect to the MySQL server using either the default or aliased IPs (in either subnet): iptables -A INPUT -p tcp --dport 3306 -j ACCEPT The server is running in a CentOS 5.4 OpenVZ/Proxmox container (2.6.32-4-pve). And, just in case you prefer to see the problem rules in the context of the iptables script, here it is (xxx=masked octect): # Flush old rules, old custom tables /sbin/iptables --flush /sbin/iptables --delete-chain # Set default policies for all three default chains /sbin/iptables -P INPUT DROP /sbin/iptables -P FORWARD DROP /sbin/iptables -P OUTPUT ACCEPT # Enable free use of loopback interfaces /sbin/iptables -A INPUT -i lo -j ACCEPT /sbin/iptables -A OUTPUT -o lo -j ACCEPT # All TCP sessions should begin with SYN /sbin/iptables -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # Accept inbound TCP packets (Do this *before* adding the 'blocked' chain) /sbin/iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow the server's own IP to connect to itself /sbin/iptables -A INPUT -i eth0 -s 208.xxx.xxx.178 -j ACCEPT # Add the 'blocked' chain *after* we've accepted established/related connections # so we remain efficient and only evaluate new/inbound connections /sbin/iptables -N BLOCKED /sbin/iptables -A INPUT -j BLOCKED # Accept inbound ICMP messages /sbin/iptables -A INPUT -p ICMP --icmp-type 8 -j ACCEPT /sbin/iptables -A INPUT -p ICMP --icmp-type 11 -j ACCEPT # ssh (private) /sbin/iptables -A INPUT -p tcp --dport 22 -m state --state NEW -s xxx.xxx.xxx.xxx -j ACCEPT # ftp (private) /sbin/iptables -A INPUT -p tcp --dport 21 -m state --state NEW -s xxx.xxx.xxx.xxx -j ACCEPT # www (public) /sbin/iptables -A INPUT -p tcp --dport 80 -j ACCEPT /sbin/iptables -A INPUT -p tcp --dport 443 -j ACCEPT # smtp (public) /sbin/iptables -A INPUT -p tcp --dport 25 -j ACCEPT /sbin/iptables -A INPUT -p tcp --dport 2525 -j ACCEPT # pop (public) /sbin/iptables -A INPUT -p tcp --dport 110 -j ACCEPT # mysql (private) /sbin/iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.xxx.xxx.184 -j ACCEPT /sbin/iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.xxx.xxx.196 -j ACCEPT /sbin/iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.xxx.xxx.251 -j ACCEPT Any ideas? Thanks in advance. :-)

    Read the article

  • Accessing SQL Server using an IP Address and Port Number ... Help!

    - by Mike
    I need to access an SQL Server that is on a machine behind a firewall and you access this machine using an ip address like 95.95.95.33:6930 (not the real ip address) ... But, you get my point that by accessing 95.95.95.33 on port 6930, the firewall routes the requests to that particular machine ... My question is ... How do you construct a connection string to access the machine at address 95.95.95.33:6930 and then further access the SQL Server on port 1433 or maybe a different port like 8484 ??? Thanks Mike

    Read the article

  • In TCPServer (Ruby) how can i get the IP/MAC from the client?

    - by a0rtega
    Hi, i want to get the IP Address of the client in a TCPServer in Ruby. And (if it is possible) the MAC Address. For example, a Time Server in Ruby, see the comment. tcpserver = TCPServer.new("", 80) if tcpserver puts "Listening" loop do socket = tcpserver.accept if socket Thread.new do puts "Connected from" + # HERE! How can i get the IP Address from the client? socket.write(Time.now.to_s) socket.close end end end end Thank you very much!

    Read the article

  • C# - How to detect all IP addresses from a LAN?

    - by SAMIR BHOGAYTA
    string strHostName = string.Empty; cmbIPAddress.Items.Clear(); // Getting Ip address of local machine... // First get the host name of local machine. strHostName = Dns.GetHostName(); // Then using host name, get the IP address list.. IPHostEntry ipEntry = Dns.GetHostByName(strHostName); IPAddress[] iparrAddr = ipEntry.AddressList; if (iparrAddr.Length 0) { for (int intLoop = 0; intLoop cmbIPAddress.Items.Add(iparrAddr[intLoop].ToString()); }

    Read the article

  • Was a Big Fish in a Little Pond, Am Now a Little Fish in a Big Pond. How Do I Grow? [closed]

    - by Ziv
    I've finished high school where I was in the top three in my class, I studied a little and there too I was pretty much Big Fish in a bigger pond than high school. Now I got into my first job in a very big company, there are some incredibly talented programmers and researchers here (mostly in departments not related to mine) and for the first time I really feel like I'm incredibly average - I do not want to be average. I read technical books all the time, I try to code on my personal time but I don't feel like that's enough. What can I do to become a leading programmer again in this big company? Is there anything specifically that can be done to make myself known here? This is a very big company so in order to advance you must be very good and shine in your field.

    Read the article

  • How to get ip address programactically on Debian based system?

    - by gc
    I'm trying to retrieve the ip address of the local machine in my program. The OS running is Ubuntu 8.10. I tried using gethostname() and gethostbyname to do it. All I can get is 127.0.1.1. I learned that it seems to be a Debian thing: This thread explained it. The content of my /etc/hosts file is also: 127.0.0.1 localhost 127.0.1.1 mymachine In this case, is there any other way to programactically (prefer C or C++) to get the ip address without modifying the system file on the machine? Thanks in advance. g.c.

    Read the article

  • How much effort does it take to spoof an Ip Address in a call to a webservice?

    - by Rory Becker
    I don't want to know how... Just how complicated.... I'm thinking of securing a webservice or 2 based on the incoming client ipaddress of the caller. Is this in any way secure? Surely if the IPaddress was being spoofed then the result would have to be sent back to the address that was being spoofed and therefore not reach the spoofer? Update: Ok so from what I can tell.... I should create a Gettoken() method which checks the IPaddress and passes out a cryptographically significant token with a timeout to any valid IP address. This is then required by any other method before any kind of side effect is allowed. Since an Attacker can't (likely) get the token without having a valid IP, he will be unable to validly call any of my "dangerous" webmethods ?

    Read the article

  • GRE keepalive with Linux and RouterOS

    - by eri
    I have a Linux host and couple of routerboadrs. I created a GRE tunnel, but Linux does not answer keepalive packages. Then router mark gre connection as unreachable, so I cant send to Linux host from router subnet. If linux sends something into tunnel (ping, etc.) - RouterOS mark connection as reacheble. Second and next packages routed nicely until one minute idle (no traffic). Tunnel in linux a make in this way: remote=x.x.x.x dev=gre21 network=10.21.0.0/16 ip tunnel add ${dev} mode gre remote ${remote} ttl 255 ip addr add 172.16.1.1/24 peer 172.16.1.21 dev ${dev} ip link set ${dev} up ip route add ${network} dev ${dev} And ip l: 14: gre21: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN link/gre 0.0.0.0 peer 109.60.170.15 How to set state "running"? How to keep alive tunnel? Ping in cron?

    Read the article

  • VPN, Tunneling to hide 'real IP' through my proxy server while showing the client IP on 'real' server side

    - by mickula
    I would like to hide my 'main server' behind the load balancer, call it 'proxy server' Although I use some closed-source software on 'main server' and it needs the client IP address to operate well. When I'm setting up some VPN connection, in that software it displays the IP address of my 'proxy server'. Is there any option to set up such tunneling or vpn to: not reveal IP of 'main server' show the IP of 'client' in 'application' on 'main server' I will be grateful for all your replies and ideas.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >