Search Results

Search found 23193 results on 928 pages for 'apple remote desktop'.

Page 433/928 | < Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >

  • What would cause my Windows machine to seize?

    - by Coltin
    I run Windows XP SP2 on a Desktop I built (I know that doesn't provide much, but I can't say "on a Dell X103938R" or something). It has 'seized' about 7 times in its year and a half life. Everything freezes. I can't move the mouse cursor and the keyboard seems unresponsive. I can turn the monitor on and off and it will hold the last image. The light for the mouse is responsive if I move it. The keyboard lights change when pressed (cap locks, etc). I've waited upto ten minutes for a change, nothing. I haven't connected any activity to the seizing. It's happened when all I was "running" were fullscreen programs (games), just checking email, or once when I was sitting at my desktop (I was reading a book and when I tried to use the mouse, nothing). I've never been able to figure it out. I have to hard reset, and then its fine. It doesn't file system check or anything (not sure if Windows does that). No error when I load up the computer, nothing. If I had uTorrent open, it will have to recheck the torrent files to make sure they weren't corrupted though. (It's not always open when it seizes either). I'm using an AMD Athlon 5400+ with a NVidia GeForce 8600 GT, if that helps. I'm using two hard drives, 500Gb Wester Digital with a 1Tb Hitachi.

    Read the article

  • USB 3.0 hard disk not detected on a particular host controller?

    - by Alvin Wong
    I have a USB 3.0 hard disk which has always been working on my desktop with an XHCI. Now I just bought a notebook with an XHCI (something with Intel's Ivy Bridge setup). The first time I plug the hard disk in its 3.0 port it is detected and working. A few hours later I try to connect it again, but seems that the notebook just ignored it! The light on the hard disk didn't blink as usual (instead it is hold at on). I then tested it with my desktop again and it is working perfectly. It gets trickier when I plug it in the USB 2.0 port of that notebook it is detected and working perfectly (despite the slower speed). Then I try to plug in an USB 2.0 USB flash drive to that USB 3.0 port, and it is detected (of course as USB 2.0). So, there are two USB 3.0 ports on my notebook's XHCI. Both of them are not working with my hard disk but working perfectly fine with my USB 2.0 UFD. What's wrong with it? When I plug in the hard disk, device manager doesn't change. I've tried re-installing the driver for the XHCI, but it changes nothing. Had I broke the USB 3.0-specific pins of both USB 3.0 ports?

    Read the article

  • Mercurial internal Setup on Windows 7 - Exception happened during processing of request from ...

    - by Sad0w1nL1ght
    Hy, i have 1 central repository and many locals. On my machine i have local and a central repository too. I can make clone/commit/update/push/pull very easy between the local and central repository on my local machine. but when i want to make a clone from another machine it gets an error. listening at http://MyLocalMachine:8000/ (bound to *:8000) ---------------------------------------- Exception happened during processing of request from ('192.168.0.194', 49319) Traceback (most recent call last): File "SocketServer.pyc", line 558, in process_request_thread File "SocketServer.pyc", line 320, in finish_request File "mercurial\hgweb\server.pyc", line 47, in __init__ File "SocketServer.pyc", line 615, in __init__ File "BaseHTTPServer.pyc", line 329, in handle File "BaseHTTPServer.pyc", line 323, in handle_one_request File "mercurial\hgweb\server.pyc", line 79, in do_GET File "mercurial\hgweb\server.pyc", line 70, in do_POST File "mercurial\hgweb\server.pyc", line 63, in do_write File "mercurial\hgweb\server.pyc", line 127, in do_hgweb File "mercurial\hgweb\hgweb_mod.pyc", line 86, in __call__ File "mercurial\hgweb\hgweb_mod.pyc", line 118, in run_wsgi ErrorResponse ---------------------------------------- The command line wich started the central repo: hg serve -R TT -n TTZoli The command from remote machine for cloning: hg clone --pull http://MyLocalMachine:8000/TT Config for the central repo: [ui] username = MyLocalUserName username = test <[email protected]> with this user i'm trying to acces the central repo [web] push_ssl = false Config for the remote repo: [ui] username = test <[email protected]> [web] push_ssl = false I'm not sure if it's relevant,my firewall is turned off on both machines, and the files in /hg folder are not versioned on the server, except hgignore. Could you please suggest some ideas? What could be the problem? Thanks in advance!

    Read the article

  • Computer resetting semi-randomly

    - by Peter
    Hi, I'm having a problem with my desktop whereby it sometimes resets itself semi-randomly. For example, I'll switch it on, it'll boot an OS and shortly after getting to the desktop it will immediately reset with no warning. The time isn't consistent - sometimes it does it before reaching login. I'm pretty sure it's not an OS thing; have tried Ubuntu and a Windows install and both exhibit it. It also doesn't appear to be heat-related because sometimes it appears to be able to "get past" it and will then run stably even under load; if anything it seems to be worse from a cold start. My gut feeling is some kind of power issue but I'm clutching at straws a little. Any suggestions on how I could go about testing it or trying to narrow the problem down would be appreciated. The machine is four years old now so while I can replace components if needed, it's not worth enough that I'm comfortable buying new parts without being pretty confident that they'll fix the problem. Thanks in advance for any help :) Edit: Okay, the motherboard is a MSI K8N SLI; CPU is an Athlon64 X2 4200+. Has one video card, a GeForce 7800GT. 1GB RAM, not sure of brand; 3 hard drives, two SATA and one PATA. Flashed motherboard to latest BIOS some time ago. Edit the Second: I thought I'd narrowed it down to the PSU for a while, but then it recurred again. I ended up pulling everything out but CPU, RAM and motherboard and it still seems to be stuffed (if anything, it's gotten worse in the last couple of days). I assume it's one of those three components, but the machine is old enough that I don't really want to spend money replacing any of them. So thanks for everyone's suggestions; much appreciated!

    Read the article

  • Lucid Lynx login issue

    - by Bart Silverstrim
    Recently upgraded from Karmic to Lynx. Upgrade seemed to go well, no noticeable issues. I logged in, and my window manager wasn't starting. An application would appear, but sans control buttons and border, so figured the windows manager needed to be given a swift kick. Opened a web browser and a quick google had me run "metacity --replace &" and everything popped up. I re-ran the Compiz configuration tool to enable my rotating desktop cube to the way I liked it, and had to reconfigure my desktop switcher to the right number of desktops (although the first time I ran it, it crashed on the panel and reloaded...odd, but once it relaunched it seemed fine.) Today I installed updates, rebooted and logged in for the second time since my upgrade. Again, the window manager was dead, and my compiz settings were gone, and the workspaces were set back to four (and when I clicked on the preferences to change them, it crashed on the panel and reloaded again). Resetting everything made things look somewhat normal again. I'm guessing it'll work until I reboot again. Googling around isn't turning up similar complaints about Lucid Lynx and the window manager. Before I go deleting preference files, anyone else know of this kind of issue and what could be done about it? Or should I start taking the stab in the dark approach of deleting preference files hoping one of them is corrupt or has something unsupported in it that's throwing LL for a loop?

    Read the article

  • How to use the correct SSH private key?

    - by Dail
    I have a private key inside /home/myuser/.ssh/privateKey I have a problem connecting to the ssh server, because i always get: Permission denied (publickey). I tried to debug the problem and i find that ssh is reading wrong file, take a look at the output: [damiano@Damiano-PC .ssh]$ ssh -v root@vps1 OpenSSH_5.8p2, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for vps1 debug1: Applying options for * debug1: Connecting to 111.111.111.111 [111.111.111.111] port 2000. debug1: Connection established. debug1: identity file /home/damiano/.ssh/id_rsa type -1 debug1: identity file /home/damiano/.ssh/id_rsa-cert type -1 debug1: identity file /home/damiano/.ssh/id_dsa type -1 debug1: identity file /home/damiano/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 74:8f:87:fe:b8:25:85:02:d4:b6:5e:03:08:d0:9f:4e debug1: Host '[111.111.111.111]:2000' is known and matches the RSA host key. debug1: Found key in /home/damiano/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/damiano/.ssh/id_rsa debug1: Trying private key: /home/damiano/.ssh/id_dsa debug1: No more authentication methods to try. as you can see ssh is trying to read: /home/damiano/.ssh/id_rsa but i don't have this file, i named it differently. How could I tell to SSH to use the correct private key file? Thanks!

    Read the article

  • Multicast hostname lookups on OSX

    - by KARASZI István
    I have a problem with hostname lookups on my OSX computer. According to Apple's HK3473 document it says for v10.6: Host names that contain only one label in addition to local, for example "My-Computer.local", are resolved using Multicast DNS (Bonjour) by default. Host names that contain two or more labels in addition to local, for example "server.domain.local", are resolved using a DNS server by default. Which is not true as my testing. If I try to open a connection on my local computer to a remote port: telnet example.domain.local 22 then it will lookup the IP address with multicast DNS next to the A and AAAA lookups. This causes a two seconds lookup timeout on every lookup. Which is a lot! When I try with IPv4 only then it won't use the multicast queries to fetch the remote address just the simple A queries. telnet -4 example.domain.local 22 When I try with IPv6 only: telnet -6 example.domain.local 22 then it will lookup with multicast DNS and AAAA again, and the 2 seconds timeout delay occurs again. I've tried to create a resolver entry to my /etc/resolver/domain.local, and /etc/resolver/local.1, but none of them was working. Is there any way to disable this multicast lookups for the "two or more label addition to local" domains, or simply disable it for the selected subdomain (domain.local)? Thank you!

    Read the article

  • LDAP, Active Directory and bears, oh my!

    - by Tim Post
    What I have: Workstations running Ubuntu Jaunty mounting /home on a remote NFS server. User accounts are still created locally on each individual workstation. Workstations running Windows XP / Vista NFS server (as noted above) Windows 2008 server All machines share a single private network (LAN). What I need to accomplish: A single, intuitive (GUI driven) place for an office administrator to create user accounts. This should let anyone login to their (linux or windows) workstation, then fire up remote desktop and use the same login to the Windows 2008 server, from any machine on the network. I have read so much on samba, LDAP vs AD, etc and now I'm even more confused than I was before I began researching the problem. Ideally, Linux and Windows users should be able to get to their local files once logged into the Win2008 server. I am a programmer, not an interoperability guru and I'm completely lost on where to even start trying to accomplish this, plus I've run out of things to Google. How would you do this? Is it even possible?

    Read the article

  • OpenWRT + OpenVPN client forwarding from lan to vpn not working

    - by Dariusz Górecki
    I've OpenWRT router with Backfire 10.03.1-rc3 (arch:brcm 2.6 kernel) I've set up an OpenVPN client connecting my router with workplace lan, and it works nicely, I can connect from router to networks (several) in workplace. My OpenVPN client uci-config looks like: config 'openvpn' 'stream_client' option 'nobind' '1' option 'float' '1' option 'client' '1' option 'reneg_sec' '0' option 'management' '127.0.0.1 31194' option 'explicit_exit_notify' '1' option 'verb' '3' option 'persist_tun' '1' option 'persist_key' '1' list 'remote' 'remote.address.cutted' option 'ca' '/lib/uci/upload/cbid.openvpn.stream_client.ca' option 'key' '/lib/uci/upload/cbid.openvpn.stream_client.key' option 'cert' '/lib/uci/upload/cbid.openvpn.stream_client.cert' option 'enable' '1' option 'dev' 'tun1' I've set the 'STREAM_VPN' Zone to allow in/out traffic, and I've added rules for zone-to-zone lan<-vpn and vpn<-lan config 'zone' option 'name' 'stream_vpn' option 'network' 'stream_vpn' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'forwarding' option 'src' 'lan' option 'dest' 'stream_vpn' config 'forwarding' option 'src' 'stream_vpn' option 'dest' 'lan' And interface config: config 'interface' 'stream_vpn' option 'proto' 'none' option 'ifname' 'tun1' option 'defaultroute' '0' option 'peerdns' '0' Now, from my router everything works nicely, the problem is that I cannot connect from computer inside a lan to hosts in networks provided by vpn connection :/ What I've missed, or what I'm doing wrong? And how can I force using specified DNS when connected to vpn? (I know that sever should use PUSH DNS option, but is PUSHes only routes)

    Read the article

  • Ubuntu karmic, chroot, Ubuntu server 8.04 LTS and Plesk

    - by morpheous
    I am pretty new to the Linux environment, and although I have been using Ubuntu Karmic desktop for development work, I have always prefered the GUI tools and very rarely use the terminal. I am about to launch a site (a VPS) which will be running Ubuntu server 8.04 LTS and Plesk. I want to install both the server (8.04 LTS) and Plesk in a 'chroot' on my Karmic desktop. I also want to test install some packages I have written for the server, and generally familiarize myself with the environment before I signup to the hosting service. I will be running a streamline server (no GUI), with only the following software: PHP Python mySQL PostgreSQL Apache Plesk Third party packages I developed In terms of mail, I think the hosting provider provides a mail service, so I dont know if I will need to run my own mail server. I will like some advice on the following: How can I install Ubuntu 8.0.4 server LTS in a chroot? How can I install Plesk in Ubuntu 8.0.4 server LTS (from the command line) Can anyone recommend how I back up the remote server when I go live (i.e. what tools to use)?. I will need to back up both databases, as well as some config data and installation packages

    Read the article

  • How to avoid ugly dithering when running KDE over VNC?

    - by Chris Jester-Young
    I'm currently setting up a new Xen paravirt domain running KDE (4.2.2, from Kubuntu 9.04). As I have been unable to get the virtual framebuffer working in it, I've decided to set up VNC (from the vnc4server package), and run KDE over Xvnc. This is all fine and good, and KDE starts up okay. However, all the colours look dithered, especially on the task bar and title bar, making them impossible to see. From my web searches, it appears to be because these items are drawn using Porter-Duff. This is especially the case when using the Oxygen style, and Oxygen and Ozone window titlebars (selecting these styles generates messages about Porter-Duff being unavailable); not using those styles at least makes most of the UI widgets and window titles usable again. But this doesn't solve the problem for the task bar, nor for the desktop, where the only theme available to me is Oxygen (this is under the "Desktop Settings - Plasma Workspace" window, just for reference). So, unless I have a way to use a non-Porter-Duff theme for those, it seems that KDE would still be unusable under VNC. So if someone experienced with KDE can advise on how to work around, or even fix, these issues, I'd appreciate it very much. :-)

    Read the article

  • FTP not listing directory NcFTP PASV

    - by Jacob Talbot
    I am attempting to setup Multicraft on my server, all is running smoothly however the FTP won't allow anyone to connect from a remote FTP client, where net2ftp will work smoothly from a remote location. I have included the transcript from my FTP client, Transmit below to give you an idea of what's going on. I have disabled iptables as well, and still no luck either way. Transmit 4.1.7 (x86_64) Session Transcript [Version 10.8.2 (Build 12C54)] (21/10/12 11:23 PM) LibNcFTP 3.2.3 (July 23, 2009) compiled for UNIX 220: Multicraft 1.7.1 FTP server Connected to ateam.bn-mc.net. Cmd: USER jacob.9 331: Username ok, send password. Cmd: PASS xxxxxxxx 230: Login successful Cmd: TYPE A 200: Type set to: ASCII. Logged in to ateam.bn-mc.net as jacob.9. Cmd: SYST 215: UNIX Type: L8 Cmd: FEAT 211: Features supported: EPRT EPSV MDTM MLSD MLST type*;perm*;size*;modify*;unique*;unix.mode;unix.uid;unix.gid; REST STREAM SIZE TVFS UTF8 End FEAT. Cmd: OPTS UTF8 ON 200: OK Cmd: PWD 257: "/" is the current directory. Cmd: PASV Could not read reply from control connection -- timed out. (SReadline 1)

    Read the article

  • Why is my connection slow?

    - by Jay R.
    I have a Dell Precision T5400 with a Broadcom 1Gb onboard NIC. For some strange reason, when I access machines on our local network, the best I can get is around 125KB/s download speed. My laptop that has a 10/100Mb NIC onboard usually gets around 300KB/s or better from the same network resource. Both machines are plugged into the same 1Gb switch which connects to our local network wall jack at 100Mb half duplex. There is also a printer plugged into the same switch at 100Mb full. The resource I'm using for the test is a 30MB zip file copied from a jetty webserver that is running as part of a cruisecontrol installation. The cruisecontrol installation is running WindowsXP with full real-time antivirus and Altiris patch management and inventory running. That stuff on its own is eating some of the download speed. I've seen the laptop reach into the multiple MB/s download speed before, but the desktop never seems to get past 125KB/s to 130KB/s. In WindowsXP, before I upgraded the driver in the desktop, it was that slow. In Fedora, it is still slow even though it appears to be using the same driver version as the upgraded Windows driver. The upgraded Windows driver is faster, but still not nearly as fast as the laptop. What gives? Any insight to improve the situation would be appreciated. Could it be that the BroadCom board just isn't that good, or the driver in linux is just not as good as the Windows one?

    Read the article

  • Is there a way to avoid Wacom Control Panel to stop showing in certain cases?

    - by S.gfx
    This is the problem: Suddenly, you double click on desktop Wacom tablet settings icon, and it won't show the dialog. It appears to be loaded as it's shown down in the Windows taskbar. I suspect it is caused by change of resolution or some setting, maybe suddenly it sets the origin of the panel dialog at some 3000 pixels to the right or something. I have dug in the wacom_tablet.dat file to see if I can fix it changing some value there, but it looks like a log, a history, more than a ini for settings. And anyway does not solve it. My solution is having always a very complete settings file done and backed up to restore (with Wacom utility for this, which in previous driver versions did not exist) when this happens, but it is counter-productive: You change the settings even per each project (and software) needs. I have seen it happenning with Cintiq 12", intuos4 A6, Graphires, Intuos 1. Is it just me, doing something weird every time? I doubt it, it's normal use, I am amazed that it seems no one else has had this problem (or nobody asked). It happens often with typical use. Maybe it's because I'm setting a shortcut in the desktop? Weird as it works perfect until some random moment. (I have dug in Wacom's forums and FAQs, then here, but nothing related to it. Neither in "related questions".) The thing happens in Win XP, 7, etc. It's done so for years in my experience, and several times at work, which is worse.

    Read the article

  • SSH works in putty but not terminal

    - by Ryan Naddy
    When I try to ssh this in a terminal: ssh [email protected] I get the following error: Connection closed by 69.163.227.82 When I use putty, I am able to connect to the server. Why is this happening, and how can I get this to work in a terminal? ssh -v [email protected] OpenSSH_6.0p1 (CentrifyDC build 5.1.0-472) (CentrifyDC build 5.1.0-472), OpenSSL 0.9.8w 23 Apr 2012 debug1: Reading configuration data /etc/centrifydc/ssh/ssh_config debug1: /etc/centrifydc/ssh/ssh_config line 52: Applying options for * debug1: Connecting to sub.domain.com [69.163.227.82] port 22. debug1: Connection established. debug1: identity file /home/ryannaddy/.ssh/id_rsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_rsa-cert type -1 debug1: identity file /home/ryannaddy/.ssh/id_dsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_dsa-cert type -1 debug1: identity file /home/ryannaddy/.ssh/id_ecdsa type -1 debug1: identity file /home/ryannaddy/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5 debug1: match: OpenSSH_5.1p1 Debian-5 pat OpenSSH_5* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.0 debug1: Miscellaneous failure Cannot resolve network address for KDC in requested realm debug1: Miscellaneous failure Cannot resolve network address for KDC in requested realm debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP Connection closed by 69.163.227.82

    Read the article

  • Sony PMB causing failure to load Windows 7 Pro 64-bit normally or even Safe Mode

    - by Wesley
    After installing Sony's Picture Motion Browser on my desktop with Windows 7 Pro x64, it always goes to Startup Repair due to Windows 7 failing to start. This always happens after I try to install it. I've installed with all unnecessary programs closed and all disk drives and unnecessary usb ports empty. I don't exactly know what is causing the problem. Any ideas? My desktop is an HP m8530f. http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01469325&tmp_task=prodinfoCategory&lc=en&dlc=en&cc=us&product=3740333&lang=en Only upgrades are an HD4350 and a 500W PSU. EDIT: Windows 7 cannot start now. I'm currently running diagnostic tests from the BIOS. EDIT: Here are the problem details. Problem Signature: Problem Event Name: StartupRepairOffline Problem Signature 01: 6.1.7600.16385 Problem Signature 02: 6.1.7600.16385 Problem Signature 03: unknown Problem Signature 04: 21201022 Problem Signature 05: AutoFailover Problem Signature 06: 8 Problem Signature 07: CorruptFile OS Version: 6.1.7600.2.0.0.256.1 Local ID: 1033 CONCLUSION: So, I think Sony PMB may have caused some sort of corruption in the system files. So if you have Windows 7 and plan on installing Sony PMB, find a Vista or XP machine to install on.

    Read the article

  • Unable to use OpenGL or install nVidia driver on openSUSE 12.2

    - by djechelon
    I have an ASUS N76VZ laptop with 12.2 openSUSE and GeForce GT650M card. I found that KDE doesn't allow me to use OpenGL rendering. I tried to install nVidia's driver from script but once it writes the xorg.conf file I'm unable to boot desktop. I have the following errors in system log Oct 30 08:28:13 RAYNOR kdm[2727]: X server died during startup Oct 30 08:28:13 RAYNOR kdm[2727]: X server for display :0 cannot be started, session disabled I noticed that the /etc/X11/xorg.conf backup file was empty, so I renamed the new xorg.conf and left none: the desktop booted!!! How can I fix OpenGL rendering with or without driver installation? [Update]: Xorg.0.log says [ 1434.207] compiled for 4.0.2, module version = 1.0.0 [ 1434.207] Module class: X.Org Server Extension [ 1434.207] (II) NVIDIA GLX Module 304.60 Sun Oct 14 20:44:54 PDT 2012 [ 1434.207] (II) Loading extension GLX [ 1434.207] (II) LoadModule: "record" [ 1434.207] (II) Loading /usr/lib64/xorg/modules/extensions/librecord.so [ 1434.207] (II) Module record: vendor="X.Org Foundation" [ 1434.207] compiled for 1.12.3, module version = 1.13.0 [ 1434.207] Module class: X.Org Server Extension [ 1434.207] ABI class: X.Org Server Extension, version 6.0 [ 1434.207] (II) Loading extension RECORD [ 1434.207] (II) LoadModule: "dri" [ 1434.207] (II) Loading /usr/lib64/xorg/modules/extensions/libdri.so [ 1434.207] (II) Module dri: vendor="X.Org Foundation" [ 1434.207] compiled for 1.12.3, module version = 1.0.0 [ 1434.207] ABI class: X.Org Server Extension, version 6.0 [ 1434.207] (II) Loading extension XFree86-DRI [ 1434.207] (II) LoadModule: "nvidia" [ 1434.208] (II) Loading /usr/lib64/xorg/modules/drivers/nvidia_drv.so [ 1434.208] (II) Module nvidia: vendor="NVIDIA Corporation" [ 1434.208] compiled for 4.0.2, module version = 1.0.0 [ 1434.208] Module class: X.Org Video Driver [ 1434.208] (II) NVIDIA dlloader X Driver 304.60 Sun Oct 14 20:24:42 PDT 2012 [ 1434.208] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs [ 1434.208] (++) using VT number 8 [ 1434.320] (EE) No devices detected. [ 1434.320] Fatal server error: [ 1434.320] no screens found [ 1434.320] Please consult the The X.Org Foundation support at http://wiki.x.org for help.

    Read the article

  • How to remove static IP from Mitel 5312 and enable DHCP

    - by jimbo
    I'm not sure this is the right forum for this question -- although I'm confident I'll be told if not! -- but I've read the fine manual (at least, such a manual as I have), I've googled and I cannot get any insight into where to even start solving this problem. I have a bunch of Mitel 5312 handsets, talking to a 3300 ICP controller. Some handsets are at a remote location, get an address from my DHCP server over there, and use the Mitel "Teleworker" extension to connect in over the Internet. The remaining handsets were set up with static IPs by a BT-supplied engineer, on the same subnet as the ICP itself. So far, so good. I have one remaining teleworker licence, and need to move a handset from the home location to the remote. I've managed to boot it and configure teleworker, but I cannot for the life of me see where I tell it to forget its static IP, and make a DHCP request. Any ideas? Should I be looking on the controller, or holding magic combinations of buttons on the handset itself? EDIT: Following some advice from Robert, below, I've broken out a spare device and reassigned the profile for this user's extension to the MAC of the new phone, and a new profile to the old MAC. Unfortunately this still doesn't get me anywhere -- the new handset now asks for the teleworker install password. I suspect I'm going to have to get a Mitel engineer involved here, since I've never been given that password... Unless anyone has any great ideas?

    Read the article

  • Windows 8 folder to folder sync software

    - by Danny
    I'm looking for direct folder to folder synchronization in Windows 8. I was previously using Live Mesh to accomplish this, but now it looks like that is no longer an option. Note that I'm talking about direct folder to folder sync between different computers, not syncing to the cloud. I'm aware of products like Google Drive, SkyDrive, Dropbox, etc. The problem with them is the space limitation. Basically, I was syncing important files before between my desktop and all of my laptops. One folder for example is My Pictures. This folder has almost 40 gigs of files, which is why the options listed above are not going to work for me. Just need direct syncing, nothing stored on the cloud. I was told by a Microsoft employee that SkyDrive would be replacing Mesh and would provide all the same functionality. So far this looks to be completely false, since the ability to remote desktop is gone along with folder to folder sync. Unless I'm just missing something?

    Read the article

  • How can I display additional boot and shutdown information on the Windows 7 welcome screen?

    - by Daniel Saner
    There is a small tweak, I believe it is a registry key, that allows to display additional information on the Welcome and Shutting down screens of Windows 7 (and most likely Vista, too). I have activated this tweak on one of my systems; unfortunately I forgot how I did it, and I can't seem to find the website that originally gave me that information. Usually, the Windows 7 welcome screen will just display "Welcome" when logging in. With the tweak activated, my Welcome screen gives status information such as "Loading user settings" or "Preparing desktop". When shutting down, the default screen simply says "Shutting down". With the tweak activated, it gives additional status information such as "Stopping Windows services". This appears the same way that Windows gives information when updates are installed or configured during the startup or shutdown procedure, and I find them quite helpful in getting a feel for what task takes how long during that process. The only setting I was able to find is the Boot log checkbox on the Boot tab of the msconfig application. However, this results in Windows displaying console logs of drivers it is loading, etc., instead of the animated Windows title. This is NOT the setting I am looking for. The "additional boot information" setting that I have activated on this system still displays the regular animated Windows logo, and only replaces the strings displayed on the blue Welcome and Shutdown screens. Could someone direct me to the registry key (or whatever setting) that is used to get this behaviour? Edit: Here are a few pictures of the enhanced Welcome and Shutdown screens taken with my mobile phone—they're in German though. Login screens "Waiting for User Profile Service" and "Preparing desktop": Logout screen "Stopping Windows services":

    Read the article

  • Keyboard issue when using kitty+puttycyg but not when using putty or cygwin alone

    - by kamaradclimber
    I would like to use a unique way to use console on my windows setup. Previously I used putty for remote access to linux servers and cygwin to have unix-like tools on windows. Then I discovered kitty which is a patched putty and have added the puttycyg patch. It provides the same way to connect to remote and local console. However, there is a strange behavior using vim when connected to the local console (using the puttycyg patch) : keys display A/B/C/D and replace the current character by these letter. In insert mode it does replace the caracter, in normal mode, no modification is made to the document even if the caracter is displayed as replaced. For instance, when I type : fixed bug with product deleted I get : fixed bbug wiwith prprodudueleteted I have read a lot of questions about this type of issue 3, 4 and googled it but there is no answer that work for me. The issue is present only for the setup kitty+puttycyg patch : cygwin alone works perfectly (and putty alone works also for access to linux servers). Any help would be appreciated !

    Read the article

  • Connecting remotely to an SQL server inside a LAN

    - by vondip
    Hello everyone, I am using SQL server 2008 inside my home lan. I've configured it to accept remote connections and I can now connect to the server from other pcs inside the lan. The problems rises when I try connecting to the server from a computer outside of my home lan. I've disabled my router's firewall and I've configured a virtual server on port 1433 forwarding to the correct lan ip. What's wrong? why is it not working? Thank you very much for your help~! Edit: This is the error I keep getting: A network related or instance specific error occured while establishing connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that the SQL SERVER is configued to allow remote connections. (provider : Sql network interfaces, error: 25- Connection string is not valid) OK these are my router's details: edimax br-6204wg I am not sure how I am supposed to browse google.com. can you be a bit more specific?

    Read the article

  • The Network folder specified is currently mapped using a different user name and password

    - by Frank Thornton
    I have a NAS device, it has 3 shares. On one computer I have access to all 3 of the shares. On another computer I keep getting this error when try and add a 2nd one. The Network folder specified is currently mapped using a different user name and password [...] That is the message I keep getting. What causes that? EDIT: Every share has it's own username and password. EDIT: NET USE on the one running 3 from the same NAS device New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------------------- OK T: \\192.168.2.5\SHARE1 Microsoft Windows Network OK X: \\Nas-1dsho-abc\SHARE2 Microsoft Windows Network Disconnected Y: \\192.168.2.9\backups Microsoft Windows Network OK Z: \\Nas-1dsho-abc\cbackups Microsoft Windows Network The command completed successfully. NET USE on the other: New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------------------- OK Y: \\192.168.2.5\SHARE1 Microsoft Windows Network Unavailable Z: \\192.168.2.5\SHARE2 Microsoft Windows Network The command completed successfully.

    Read the article

  • Trouble getting latest version of Git

    - by TheMethod
    I am using Ubuntu 10.04 LTS. I'm looking at using git as source control for personal projects and Github as a remote repository. I was having trouble pushing a commit to my remote github repo getting the following error message: The requested URL returned error: 403 while accessing https://github.com/Jstall/helloworld.git/info/refs When I did some digging I found that the problem could be me not having the latest version of Git. When I did a --version I found that I have version 1.7.0.4 locally. So I tried to update git using: sudo apt-get install git but get the following error: Reading package lists... Done Building dependency tree Reading state information... Done Package git is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package git has no installation candidate I've tried running: sudo apt-get update and trying again but it didn't seem to make a difference. I'm not sure if it's relevant but I'm also getting a couple of 404's when I run update: Err http://wine.budgetdedicated.com edgy/main Packages 404 Not Found Fetched 4,117B in 0s (5,142B/s) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/edgy/universe/binary-i386/Packages.gz 404 Not Found [IP: 91.189.91.15 80] W: Failed to fetch http://wine.budgetdedicated.com/apt/dists/edgy/main/binary-i386/Packages.gz 404 Not Found I'm not sure when I should try next. Could anyone suggest a course of action to get this resolved? Any advice would be appreciated. Thanks much!

    Read the article

  • Compress a folder of PDF files into separate zip archives

    - by Panrubius
    I wanted to take a folder full of PDF files and create a number of separate zip files, after following the advice on this question everything worked *almost*perfectly. Here's what happened: When I issued this command in Terminal: zip -s 5m -r ~/Desktop/invoices ~/Desktop/Invoices/ Everything worked really well, in that I got 11 ZIP files of approximately 5 MB each; placed in the folder specified. However, the files they outputted were named as follows: invoices.z01 invoices.z02 invoices.z03 invoices.z04 invoices.z05 invoices.z06 invoices.z07 invoices.z08 invoices.z09 invoices.z10 invoices.zip So as you can see only invoices.zip has been named correctly. I could go through and rename them one by one, but seriously, if we start doing that then what in the name of Evolution are computers for?! Now, I am also aware that I'm relatively new to the Terminal; so I could be making a very silly mistake somewhere. If that's the case, please be patient :-) Any help would be greatly appreciated. One last note: I'm quadriplegic so I would like to avoid GUI applications as much as possible, I use voice recognition software you see this working in the Terminal is much much easier.

    Read the article

< Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >