Search Results

Search found 24734 results on 990 pages for 'floating point conversion'.

Page 434/990 | < Previous Page | 430 431 432 433 434 435 436 437 438 439 440 441  | Next Page >

• unable to sniff traffic despite network interface being in monitor or promiscuous mode

  - by user65126

  I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

  Read the article

• MySQL Memory usage

  - by Rob Stevenson-Leggett

  Our MySQL server seems to be using a lot of memory. I've tried looking for slow queries and queries with no index and have halved the peak CPU usage and Apache memory usage but the MySQL memory stays constantly at 2.2GB (~51% of available memory on the server). Here's the graph from Plesk. Running top in the SSH window shows the same figures. Does anyone have any ideas on why the memory usage is constant like this and not peaks and troughs with usage of the app? Here's the output of the MySQL Tuning Primer script: -- MYSQL PERFORMANCE TUNING PRIMER -- - By: Matthew Montgomery - MySQL Version 5.0.77-log x86_64 Uptime = 1 days 14 hrs 4 min 21 sec Avg. qps = 22 Total Questions = 3059456 Threads Connected = 13 Warning: Server has not been running for at least 48hrs. It may not be safe to use these recommendations To find out more information on how each of these runtime variables effects performance visit: http://dev.mysql.com/doc/refman/5.0/en/server-system-variables.html Visit http://www.mysql.com/products/enterprise/advisors.html for info about MySQL's Enterprise Monitoring and Advisory Service SLOW QUERIES The slow query log is enabled. Current long_query_time = 1 sec. You have 6 out of 3059477 that take longer than 1 sec. to complete Your long_query_time seems to be fine BINARY UPDATE LOG The binary update log is NOT enabled. You will not be able to do point in time recovery See http://dev.mysql.com/doc/refman/5.0/en/point-in-time-recovery.html WORKER THREADS Current thread_cache_size = 0 Current threads_cached = 0 Current threads_per_sec = 2 Historic threads_per_sec = 0 Threads created per/sec are overrunning threads cached You should raise thread_cache_size MAX CONNECTIONS Current max_connections = 100 Current threads_connected = 14 Historic max_used_connections = 20 The number of used connections is 20% of the configured maximum. Your max_connections variable seems to be fine. INNODB STATUS Current InnoDB index space = 6 M Current InnoDB data space = 18 M Current InnoDB buffer pool free = 0 % Current innodb_buffer_pool_size = 8 M Depending on how much space your innodb indexes take up it may be safe to increase this value to up to 2 / 3 of total system memory MEMORY USAGE Max Memory Ever Allocated : 2.07 G Configured Max Per-thread Buffers : 274 M Configured Max Global Buffers : 2.01 G Configured Max Memory Limit : 2.28 G Physical Memory : 3.84 G Max memory limit seem to be within acceptable norms KEY BUFFER Current MyISAM index space = 4 M Current key_buffer_size = 7 M Key cache miss rate is 1 : 40 Key buffer free ratio = 81 % Your key_buffer_size seems to be fine QUERY CACHE Query cache is supported but not enabled Perhaps you should set the query_cache_size SORT OPERATIONS Current sort_buffer_size = 2 M Current read_rnd_buffer_size = 256 K Sort buffer seems to be fine JOINS Current join_buffer_size = 132.00 K You have had 16 queries where a join could not use an index properly You should enable "log-queries-not-using-indexes" Then look for non indexed joins in the slow query log. If you are unable to optimize your queries you may want to increase your join_buffer_size to accommodate larger joins in one pass. Note! This script will still suggest raising the join_buffer_size when ANY joins not using indexes are found. OPEN FILES LIMIT Current open_files_limit = 1024 files The open_files_limit should typically be set to at least 2x-3x that of table_cache if you have heavy MyISAM usage. Your open_files_limit value seems to be fine TABLE CACHE Current table_cache value = 64 tables You have a total of 426 tables You have 64 open tables. Current table_cache hit rate is 1% , while 100% of your table cache is in use You should probably increase your table_cache TEMP TABLES Current max_heap_table_size = 16 M Current tmp_table_size = 32 M Of 15134 temp tables, 9% were created on disk Effective in-memory tmp_table_size is limited to max_heap_table_size. Created disk tmp tables ratio seems fine TABLE SCANS Current read_buffer_size = 128 K Current table scan ratio = 2915 : 1 read_buffer_size seems to be fine TABLE LOCKING Current Lock Wait ratio = 1 : 142213 Your table locking seems to be fine The app is a facebook game with about 50-100 concurrent users. Thanks, Rob

  Read the article

• Intel Rapid Storage / Smart Response SSD caching issue

  - by goober

  Background Recently built my own PC. It works! Almost. It's been a while since getting into the guts of these things, so I'm familiar but may be missing something simple. FYI, I don't care about blowing the OS away -- it's brand new and we can go back from scratch as many times as necessary. Goal / Issue I'd like to use the SSD to take advantage of Intel's Smart Response technology (allows the SSD to act as a cache for HDDs) I would like the SSD cache to act as a cache for my HDDs, which I would like to be in a RAID1 array (so I get the speed from the SSD and the redundancy from the RAID1) However, Windows only sees the drive in device manager (not as a drive), so I'm unsure what to do about that. Related: as far as I know, for this to work, the drives all have to be in a single RAID array (i.e. a RAID0 pairing of the SSD and the RAID1 HDD array). However, when attempting this at the BIOS level, I am told there is not enough space for an array. Steps so Far Moved the SSD onto the Intel controller (I'd had it on the Marvel 6.0 controller instead of the Intel controller, so the BIOS was only seeing it in a strange way) Updated the BIOS of the motherboard to the latest version Reinstalled Intel's RST (iRST?) software several times, as some forums reported it working after reinstalling 3 times (which does not inspire confidence). Checked Intel storage: it does see the SSD as a physical, non-RAID device. However, it says no space exists if I try to create an array. Checked the BIOS: it does not show up in the boot order, but is an option that can be selected under boot options. Tried the firmware update for that model. Issue: the firmware CD doesn't detect a drive; maybe the Intel storage controller is making it difficult? moved the ssd to the marvel controller. The firmware update cd appeared to hang while searching for drives. swapped out the SATA cable for the manufacturer's and moved back to the intel storage controller. Noticed at this point that in the Intel RST software, a device DOES show up in addition to the RAID set -- only shown as a "60 GB internal disk". Windows doesn't appear to see it as a drive, but it does still show in device manager. Move SSD to port from 0-3 on MOBO and set SATA mode to IDE (after disconnecting RAID1 config) to allow the firmware update to work. Firmware was already at the latest version. Next Steps ? Components involved ASUS P8Z68-V PRO motherboard (Intel Z68 Chipset) Intel i7 2600k Processor 2 x 1TB 7200 RPM HDDs 64 GB Crucial M4 SSD (M4-CT064M4SSD2) For Reference -- Storage Configuration Intel 3 gbps Intel 3gbps Intel 6gbps Marvel 6gbps +----------+ +----------+ +----------+ +----------+ | | <----+ | | +-+ | | | |----------| | |----------| |-|--------| |----------| | | | | + | | | | | | +----------+ | +--|-------+ +-|--------+ +----------+ | | | + v v | 1 TB HDD 64 GB SSD + +> 1 TB HDD For Reference -- Intel RST (v10.8.0.1003) Screenshot Don't mind the "rebuilding" -- knocked a power cable out at one point; it's doing its job, not an indicator of a bad HDD. Any thoughts? Thanks in advance for any help!

  Read the article

• moving raid 10 to another identical server both on Smart Array 6i controllers

  - by SalimQrdl

  I have dead HP DL 380G4 with RAID 1+0 with 1 logical volume from 4x72GB drives on built-in Smart Array 6i 128Mb BBWC. It was shut down properly. It seems it was usual death for Proliant with ILO led 2,3,8 lighting. I want to move array to another identical server with same raid firmware level. What is the best strategy?: I have RAID 1+0 on bay 0 bay 1 bay 2 bay 3 As I understand bay0+bay1 are in RAID 1 , bay2+bay3 are in RAID 1, and both RAID 1 pairs are in RAID 0. So should I : Clear RAID config on new server, insert bay 0, bay 2 and power-on or Create RAID 1+0 with 1 logical volume from clear HDDs , and then poweroff ,remove HDDs and insert 2 HDDs(bay 0, bay 2) from old RAID 1+0. then power-on. (each hdd has its raid position info stored but may be could work on same config) According to documentation for Smart Array 6i it could be possible to migrate. however one requirement point is unclear for me Before you move drives, the following conditions must be met: • The array is in its original configuration. " What is orginal and non-original config for RAID 1+0? Another point "If you want to move an array to another controller, you must also consider the following additional limitations: • All drives in the array must be moved at the same time." I want to move one hdd from each RAID 1 pair. to have mirrors untouched just in case. Do they mean to move all 4 simultaniously? Smart Array 6i User Guide: Moving Drives and Arrays You can move drives to other ID positionson the same array controller. You can also move a complete arrayfrom one controller to another, even if the controllers are on different servers. Before you move drives, the following conditions must be met: • If moving thedrives to a different server, the new server must have enough empty bays to accommodate all the drives simultaneously. • The move will not result in more than 14 physical drives per controller channel. • No controller will be configured with more than 32 logical volumes. • The array has no failed or missing drives. • The array is in its original configuration. • The controller is not reading from or writing to any of the spare drives in the array. • The controller is not running capacity expansion, capacity extension, or RAID or stripe size migration. • The controller is using the latestfirmware version (recommended). If you want to move an array to another controller, you must also consider the following additional limitations: • All drives in the array must be moved at the same time. • In most cases, a moved array (and the logical drives that it contains) can still undergo arraycapacity expansion, logical drive capacity extension, or migration of RAID level orstripe size. When all the conditions have been met: Back up all data before removing any drives or changing configuration. This step is requiredif you are moving data-containing drives from a controller that does not have a battery-backed cache. Power down the system. If you are moving an array from a controller that contains a RAID ADG logical volume to a controller that does not support RAID ADG: Move the drives. Power up the system. If a 1724 POST message is displayed, drive positions were changed successfully and the configuration was updated. If a 1785 (NotConfigured)POST message is displayed: a. Power down the system immediately to prevent data loss. b. Return the drives to their original locations. c. Restore the data from backup, if necessary. Check the new drive configuration byrunning ORCA or ACU ("Configuring an Array" on page 9).

  Read the article

• Computer makes hissing noise, turns off after few seconds

  - by Kaustubh P

  I have a problem similar to the questions posted here and here. This is my config: Asus M3N78-EM, with AMD Phenom X3 720 2800 Black Edition, 4GB Transcend DDR2 RAM, Nvidia 9400GT. HD is a 160 GB IDE, and a LG IDE DVD-ROM. The power button is a bit off, I have removed the cover of the switch, and the only way it turns on is just giving the "stick" under the cover a gentle press. It turns on sometimes, and at other times, I have to cut-off the power from the PSU, and try again. I will describe my problem in as detail as possible, please bear with me: The problem has started in the last week, a few months after I changed the to the powerswitch arrangement as described above. The PC makes a hissing noise, and I wasn't able to pin-point the noise source, because of the various other fans. At first, removing the HD, rebooting w/o the HD, turning it off, reconnecting and booting made the problem go away. But of late, it doesn't happen. As suggested in the other questions, I tried reducing the load by disconnecting both the IDE drives, and the problem (noise + turn-off) still occurs. I also connected another 80G IDE HD,today morning, adn it still made that noise, and turned off. I also opened up the PSU, but I couldn't see any fault in that, I tried rotating the fan by blowing into the blades, and with my fingers, but the hissing noise didn't come from there. Or maybe the speed wasn't enough to evoke that noise. A few weeks ago: I had cleaned the Cabinet and had repasted the processor and its fan using some thermal paste. Could that be at fault? I also used a vacuum to blow the dust out of the PSU, could the power have been too much, to maybe offset the fan or something? A label on the PSU says it uses a ball-bearing fan. That only leaves me with the Processor fan and the processor itself. I didn't try removing the processor fan and processor from the motherboard, and then turning the PC on, fearing damage. Will doing so cause any damage? What can I do to localize and pin-point the problem? Also, after a few tries, the Computer starts up. Sometimes it turns of within 2 seconds, sometimes after the POST. Once it turned off at the grub. Another time it booted completely and then turned off. The only way to ensure that the PC wont turn off, is if the hissing noise stops. EDIT: I suspect it to be the Processor/Processor fan, owing to the source of noise. All the config, except for the Cabinet, is just over a year old. EDIT2: I also just remembered, that I had set the "On-power resume" to turn on, i.e. If I supply he PC with power, it will turn itself on, w/o me needing to press the switch. I had done that to workaround the faulty power-switch, as noted above. EDIT3: I calculated the power my system needs, from the antec site, and I just arrived at 292W

  Read the article

• Simple Cisco ASA 5505 config issue

  - by Ben Sebborn

  I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

  Read the article

• Accessing resources on localhost using domain credentials

  - by jas

  I'm trying to set up Team Foundation Server 2010, Sharepoint Server 2010 and Report Server 2008R2. I apologize for how long my question/problem is but I'm really lost on where to even look so am being as descriptive as possible in hopes that I'm making sense. The goal: Since developers can be inside or outside the firewall there needs to be a single http point of entry to TFS that works regardless of which side of the firewall you are and needs to work with external access to SharePoint and Report Server. Meaning we have it set up in DNS so buildserver.mydomain.com: points to the build service box which contains all of the services listed at the top of this post and specific services are defined/located by the port number. This is working great on every machine inside and out except for from the build server itself. All services must be able to work using external URLs. If I use http:// buildserver.mydomain.com:4800/tfs (the external URL) from my notebook which is behind the firewall I'm able to login with my domain credentials as expected. If the other developer points to the same URL from their home which isn't on the domain they are also able to login using their domain credentials. However if I am directly on buildserver and call SharePoint, TFS or Reporting Server from (i.e. http:// buildserver.mydomain.com:4800) itself using the external URL, I am prompted for a username and password. Entering my domain credentials results in another prompt to enter my credentials again. It will prompt three times regardless of which credentials are used (I have rights as a domain admin) and then after the third prompt directs me to a blank white page as though access was denied. There are no errors displayed on the page and nothing ends up in the event viewer. From buildserver if i use just the host name (the internal URL), then I'm prompted a single time for credentials and it works. i.e. http:// buildserver:4800/tfs works from the server itself. The behavior is identical for any service requiring authentication. Meaning from the box itself Sharepoint Central Admin, SharePoint WebApp, TFS, TFS Web Access, Report Server and Report Manager all fail using the external URL but will succeed if called using the interal URL. So the problem comes into play when configuring all of the services to work together. The only way to configure TFS is locally from the server which means I must point to the internal reporting server url (http:// buildserver:4800/reports and reportServer respectively instead of http:// buildserver.domainname.com:4800 like they need to be) since external URLs aren't working from itself. If I configure TFS to use the internal URL for Report Server then creating team projects or working in the SharePoint site for the team project fails for anyone not inside the domain since their machines have no idea who http:// buildserver:/reports even is or how to resolve them. I have configured Sharepoint with Alternate Access Mappings as well as set up Report Server to listen for external URLs. The external URLs simply aren't working when called from the server itself. I hope this makes sense. Thanks for taking the time to read this rather verbose plea for help.

  Read the article

• How to stop Apache from crashing my entire server?

  - by CyberShadow

  I maintain a Gentoo server with a few services, including Apache. It's fairly low-end (2GB of RAM and a low-end CPU with 2 cores). My problem is that, despite my best efforts, an over-loaded Apache crashes the entire server. In fact, at this point I'm close to being convinced that Linux is a horrible operating system that isn't worth anyone's time looking for stability under load. Things I tried: Adjusting oom_adj for the root Apache process (and thus all its children). That had close to no effect. When Apache was overloaded it would bring the system to a grind, as the system paged out everything else before it got to kill anything. Turning off swap. Didn't help, it would unload memory paged to binaries of processes and other files on /, thus causing the same effect. Putting it in a memory-limited cgroup (limited to 512 MB of RAM, 1/4th of the total). This "worked", at least in my own stress tests - except the server keeps crashing under load (basically stalling all other processes, inaccessible via SSH, etc.) Running it with idle I/O priority. This wasn't a very good idea in the end, because it just caused the system load to climb indefinitely (into the thousands) with almost no visible effect - until you tried to access an unbuffered part of the disk. This caused the task to freeze. (So much for good I/O scheduling, eh?) Limiting the number of concurrent connections to Apache. Setting the number too low caused web sites to become unresponsive due to most slots being occupied with long requests (file downloads). I tried various Apache MPMs without much success (prefork, event, itk). Switching from prefork/event+php-cgi+suphp to itk+mod_php. This improved performance, but didn't solve the actual problem. Switching I/O schedulers (cfq to deadline). Just to stress this out: I don't care if Apache itself goes down under load, I just want the rest of my system to remain stable. Of course, having Apache recover quickly after a brief period of intensive load would be great to have, but one step at a time. Right now I am mostly dumbfounded by how can humanity, in this day and age, design an operating system where such a seemingly simple task (don't allow one system component to crash the entire system) seems practically impossible - or at least, very hard to do. Please don't suggest things like VMs or "BUY MORE RAM". Some more information gathered with a friend's help: The processes hang when the cgroup oom killer is invoked. Here's the call trace: [<ffffffff8104b94b>] ? prepare_to_wait+0x70/0x7b [<ffffffff810a9c73>] mem_cgroup_handle_oom+0xdf/0x180 [<ffffffff810a9559>] ? memcg_oom_wake_function+0x0/0x6d [<ffffffff810aa041>] __mem_cgroup_try_charge+0x32d/0x478 [<ffffffff810aac67>] mem_cgroup_charge_common+0x48/0x73 [<ffffffff81081c98>] ? __lru_cache_add+0x60/0x62 [<ffffffff810aadc3>] mem_cgroup_newpage_charge+0x3b/0x4a [<ffffffff8108ec38>] handle_mm_fault+0x305/0x8cf [<ffffffff813c6276>] ? schedule+0x6ae/0x6fb [<ffffffff8101f568>] do_page_fault+0x214/0x22b [<ffffffff813c7e1f>] page_fault+0x1f/0x30 At this point, the apache memory cgroup is practically deadlocked, and burning CPU in syscalls (all with the above call trace). This seems like a problem in the cgroup implementation...

  Read the article

• Windows XP Video Configuration Issues

  - by Matt

  Recently I had my motherboard burn out on me. Needing the machine for work, I purchased a different motherboard and installed that. Generally a reinstall of windows is good at that point but I am not in a position to do that so I just decided I would live with it for now. When I can log-in, everything works fine, what doesn't is getting to the log-in prompt to begin with. Basically when I first installed the new mobo, every time I rebooted the machine, I would not get the windows login prompt. One of the monitors would receive a signal but the screen would be black. Moving the mouse would not show the cursor and hitting the up arrow key and typing my password and hitting enter (which will normally log you in without mouse) wouldn't change anything. I would then change the monitor configuration around (2 lcd's and a crt) and reboot and at least one of the monitors would work and display the login prompt. I could then go into display properties and turn on the other monitors. However if I rebooted again, I would get the black screen on one monitor again. I would then have to change the configuration again to one not used before and I could re-do the manual setup at that point. I think windows saves the configurations so I had to keep giving it new ones. Needless to say I've been trying to not turn off my machine. Early this week I actually got the prompt to come up without playing musical monitors. Thinking everything was getting better, I found no harm in rebooting to install the latest windows updates. Boy was I wrong. Now no matter what I do I can't get a windows log-in prompt to display. I've tried almost every conceivable combination. The new mobo has onboard video so I set that in the bios (yea bios screen always displays fine, its not until windows boots that there is a problem) to be the primary video. Still no luck. I have two other graphics cards in the machine which I'm using. Tried all kinds of configurations between those and on-board but still get this black screen of death. I read somewhere that deleting the video drivers would reset the configurations. I logged into safe mode (which works on one monitor), and uninstalled the display drivers. Still no luck and when I booted back into safe mode, it wanted to install new hardware and the display adapters weren't there as expected. Anyone have any ideas? A fresh install would be a pain and I might be getting my old board back from RMA soon so not sure I want to go through with that just yet. Only thing I can think of is to continue to try other combinations like physically removing the graphics cards. They are both EVGA 8600 cards and the windows boot screen does display fwiw.

  Read the article

• All client browsers repeatedly asking for NTLM authentication when running through local proxy server

  - by Marko

  All client browsers repeatedly asking for NTLM authentication when running through local proxy server. When pointing browsers through the local proxy to the internet, some but not all clients are being repeatedley prompted to authenticate to the proxy server. I have inspected the headers using firefox live headers as well as fiddler, and in all cases the authentication prompts happen when requesting SSL resources. an example of this would be as follows: GET http://gmail.google.com/mail/ HTTP/1.1 Accept: image/gif, image/jpeg, image/pjpeg, image/pjpeg, application/x-shockwave- flash, application/x-ms-application, application/x-ms-xbap, application/vnd.ms- xpsdocument, application/xaml+xml, */* Accept-Language: en-gb User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Accept-Encoding: gzip, deflate Proxy-Connection: Keep-Alive Host: gmail.google.com GET http://gmail.google.com/mail/ HTTP/1.1 Accept: image/gif, image/jpeg, image/pjpeg, image/pjpeg, application/x-shockwave- flash, application/x-ms-application, application/x-ms-xbap, application/vnd.ms- xpsdocument, application/xaml+xml, */* Accept-Language: en-gb User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Accept-Encoding: gzip, deflate Proxy-Connection: Keep-Alive Host: gmail.google.com Proxy-Authorization: NTLM TlRMTVNTUAABAAAAB7IIogkACQAvAAAABwAHACgAAAAFASgKAAAAD1dJTlhQMUdGTEFHU0hJUDc= GET http://gmail.google.com/mail/ HTTP/1.1 Accept: image/gif, image/jpeg, image/pjpeg, image/pjpeg, application/x-shockwave- flash, application/x-ms-application, application/x-ms-xbap, application/vnd.ms- xpsdocument, application/xaml+xml, */* Accept-Language: en-gb User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Accept-Encoding: gzip, deflate Proxy-Connection: Keep-Alive Proxy-Authorization: NTLM TlRMTVNTUAADA (more stuff goes here I cut it short) Host: gmail.google.com At this point the username and password prompt has appeared in the browser, it does not matter what is typed into this box, correct credentials, random nonsense the browser does not accept anything in this box it will continue to popup. If I press cancel, I sometimes get a http 407 error, but on other occasions I click cancel the website proceeds to download and show normally. This is repeatable with some clients running through my proxy server, but in other cases it does not happen at all. In the cases where a client computer works normally, the only difference I can see is that the 3rd request for SSL resource comes back with a 200 response, see below: CONNECT gmail.google.com:443 HTTP/1.0 User-Agent: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; Trident/5.0; MALC) Proxy-Connection: Keep-Alive Content-Length: 0 Host: gmail.google.com Pragma: no-cache Proxy-Authorization: NTLM TlRMTVNTUAADAAAAGAAYAIAAAA A SSLv3-compatible ClientHello handshake was found. I have tried resetting user accounts as well as computer accounts in Active Directory. User accounts and passwords that are being used are correct and the passwords have been reset so they are not out of sync. I have removed the clients and even the proxy server from the domain, and rejoined them. I have installed a complete separate proxy server and get exactly the same problem when I point clients to a different proxy server on a different IP address.

  Read the article

• PC runs very slowly for no apparent reason

  - by GalacticCowboy

  I have a Dell Latitude D820 that I've owned for about 2.5 years. It is a Core 2 Duo T7200 2.0GHz, with 2 GB of RAM, an 80 GB hard drive and an NVidia Quadro 120M video card. The computer was purchased in late November of 2006 with XP Pro, and included a free upgrade to Vista Business. (Vista was available on MSDN but not yet via retail, so the Vista Business upgrades weren't shipped until March of '07.) Since we had an MSDN subscription at the time, I installed Vista Ultimate on it pretty much as soon as I got it. It ran happily until sometime in the spring of 2007 when Media Center (which I had never used except to watch DVDs) started throwing some kind of bizarre SQL (CE?) error. This error would pop up at random times just while using the computer. Furthermore, Media Center would no longer start. I never identified the cause of this error. I had the Vista Business upgrade by this time, so I nuked the machine, installed XP and all the drivers, and then the Vista Business upgrade. Again, it ran happily for a few months and then started behaving badly once again. Vista Business doesn't have Media Center, so this exhibited completely unrelated symptoms. For no apparent reason and at fairly random times, the machine would suddenly appear to freeze up or run very slowly. For example, launching a new application window (any app) might take 30-45 seconds to paint fully. However, Task Manager showed very low CPU load, memory, etc. I tried all the normal stuff (chkdsk, defrag, etc.) and ran several diagnostic programs to try to identify any problems, but none found anything. It eventually reached the point that the computer was all but unusable, so I nuked it again and installed XP. This time I decided to stick with XP instead of going to Vista. However, within the past couple of months it has started to exhibit the same symptoms in XP that I used to see in Vista. The computer is still under Dell warranty until December, but so far they aren't any help unless I can identify a specific problem. A friend (partner in a now-dead business) has an identical machine that was purchased at the same time. His machine exhibits none of these symptoms, which leads me to believe it is a hardware issue, but I can't figure out how to identify it. Any ideas? Utilities? Seen something similar? At this point I can't even identify any pattern to the behavior, but would be willing to run a "stress test"-style app for as long as a couple days if I had any hope that it would find something. EDIT July 17 I'm testing jerryjvl's answer regarding the video card, though I'm not sure it fully explains the symptoms yet. This morning I ran a video stress test. The test itself ran fine, but immediately afterward the PC started acting up again. I left ProcExp open and various system processes were consuming 50-60% of the CPU but with no apparent reason. For example, "services.exe" was eating about 40%, but the sum of its child processes wasn't higher than about 5%. I left it alone for several minutes to settle down, and then it was fine again. I used the "video card stability test" from firestone-group.com. Its output isn't very detailed, but it at least exercises the hardware pretty hard. EDIT July 22 Thanks for your excellent suggestions. Here is an update on what I have tried so far. Ran memtest86, SeaTools (Seagate), Hitachi drive fitness test, video card stability test (mentioned above). The video card test was the only one that seemed to produce any results, though it didn't occur during the actual test. I defragged the drive (again...) with JkDefrag I dropped the video card

  Read the article

• Causes of sudden massive filesystem damage? ("root inode is not a directory")

  - by poolie

  I have a laptop running Maverick (very happily until yesterday), with a Patriot Torx SSD; LUKS encryption of the whole partition; one lvm physical volume on top of that; then home and root in ext4 logical volumes on top of that. When I tried to boot it yesterday, it complained that it couldn't mount the root filesystem. Running fsck, basically every inode seems to be wrong. Both home and root filesystems show similar problems. Checking a backup superblock doesn't help. e2fsck 1.41.12 (17-May-2010) lithe_root was not cleanly unmounted, check forced. Resize inode not valid. Recreate? no Pass 1: Checking inodes, blocks, and sizes Root inode is not a directory. Clear? no Root inode has dtime set (probably due to old mke2fs). Fix? no Inode 2 is in use, but has dtime set. Fix? no Inode 2 has a extra size (4730) which is invalid Fix? no Inode 2 has compression flag set on filesystem without compression support. Clear? no Inode 2 has INDEX_FL flag set but is not a directory. Clear HTree index? no HTREE directory inode 2 has an invalid root node. Clear HTree index? no Inode 2, i_size is 9581392125871137995, should be 0. Fix? no Inode 2, i_blocks is 40456527802719, should be 0. Fix? no Reserved inode 3 (<The ACL index inode>) has invalid mode. Clear? no Inode 3 has compression flag set on filesystem without compression support. Clear? no Inode 3 has INDEX_FL flag set but is not a directory. Clear HTree index? no .... Running strings across the filesystems, I can see there are what look like filenames and user data there. I do have sufficiently good backups (touch wood) that it's not worth grovelling around to pull back individual files, though I might save an image of the unencrypted disk before I rebuild, just in case. smartctl doesn't show any errors, neither does the kernel log. Running a write-mode badblocks across the swap lv doesn't find problems either. So the disk may be failing, but not in an obvious way. At this point I'm basically, as they say, fscked? Back to reinstalling, perhaps running badblocks over the disk, then restoring from backup? There doesn't even seem to be enough data to file a meaningful bug... I don't recall that this machine crashed last time I used it. At this point I suspect a bug or memory corruption caused it to write garbage across the disks when it was last running, or some kind of subtle failure mode for the SSD. What do you think would have caused this? Is there anything else you'd try?

  Read the article

• ASA 5505 stops local internet when connected to VPN

  - by g18c

  Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• Can't communicate between lan ports on openwrt router

  - by ScaryAardvark

  I've got a WBMR-HP-G300H Buffalo Airstation router on which I've installed the lates OpenWRT software. All is working well (ADSL, WIFI etc) except for one niggle. I can't communicate between lan ports. i.e. if I have one computer connected on lan port 1 and I try to ping another computer on lan port 2 then I get "destination unreachable". I can ping both computers from the router itself and can also ping each computer from a seperate laptop connected wirelessly. All computers are in the same subnet range (10.0.0.?/24). I suspect that I may need to configure a vlan on the switch but everytime I try and do this with various google'ed configuration I keep freezing out all lan-ports and I have to revert back using a wirelessly connected laptop. Here's my /etc/config/network: config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config interface 'lan' option type 'bridge' option proto 'static' option netmask '255.255.255.0' option ipaddr '10.0.0.1' option _orig_ifname 'eth0 wlan0' option _orig_bridge 'true' option ifname 'eth0' config adsl-device 'adsl' option fwannex 'a' option annex 'a2p' config interface 'wan' option _orig_ifname 'nas0' option _orig_bridge 'false' option proto 'pppoa' option encaps 'vc' option atmdev '0' option vci '38' option vpi '0' option username '?????????????' option password '??????????????' Any help would be warmly received. Here's some more config stuff. root@OpenWrt:~# ifconfig -a br-lan Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:226576 errors:0 dropped:346 overruns:0 frame:0 TX packets:269292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:26771676 (25.5 MiB) TX bytes:183986450 (175.4 MiB) eth0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb0 Link encap:Ethernet HWaddr 36:60:EC:DF:13:A1 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb1 Link encap:Ethernet HWaddr 4A:7B:75:67:54:E0 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:780 errors:0 dropped:0 overruns:0 frame:0 TX packets:780 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:58369 (57.0 KiB) TX bytes:58369 (57.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 00-24-A5-BD-66-08-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2424 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:320188 (312.6 KiB) TX bytes:0 (0.0 B) pppoa-wan Link encap:Point-to-Point Protocol inet addr:81.136.179.204 P-t-P:81.134.80.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:258894 errors:0 dropped:0 overruns:0 frame:0 TX packets:212976 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:177341656 (169.1 MiB) TX bytes:25192459 (24.0 MiB) wlan0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:204063 errors:0 dropped:0 overruns:0 frame:0 TX packets:245516 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:26613140 (25.3 MiB) TX bytes:162799765 (155.2 MiB) root@OpenWrt:~# brctl show bridge name bridge id STP enabled interfaces br-lan 8000.0024a5bd6608 no wlan0 eth0 root@OpenWrt:~# swconfig dev eth0 show Global attributes: enable_vlan: 0 Port 0: pvid: 0 link: port:0 link:up speed:1000baseT full-duplex txflow rxflow Port 1: pvid: 0 link: port:1 link:down Port 2: pvid: 0 link: port:2 link:down Port 3: pvid: 0 link: port:3 link:down Port 4: pvid: 0 link: port:4 link:up speed:100baseT full-duplex txflow rxflow auto Port 5: pvid: 0 link: port:5 link:up speed:100baseT full-duplex txflow rxflow auto Regards Mark.

  Read the article

• Capistrano + Nginx + Passenger = 403

  - by slimchrisp

  I asked this over at stackoverflow as well, but still haven't received any answers that have helped me to solve this problem. I have spent almost a week at this point trying to solve the issue, and I'm just not making any headway. It seems that this issue is pretty common, but none of the solutions I found online work for me. A buddy of mine is actually creating the same setup, and he is having the same issue. After a few days stuck with the 403 error I started over using this tutorial: http://blog.ninjahideout.com/posts/a-guide-to-a-nginx-passenger-and-rvm-server I had hoped starting from scratch using this tutorial would work, but no dice. Either way, if you view the tutorial you can see what steps I have taken. Here is essentially what I have going on. I have a VPS account on linode.com Server OS is Ubuntu 10.04 Local OS (shouldn't matter, but just so you know) used to deploy with Capistrano is Snow Leopard 10.6.6 I use RVM on the server. Version is 1.2.2 I was previously on ruby-1.9.2-p0 [ i386 ], but per the tutorial listed above I switched to ree-1.8.7-2010.02 [ i386 ]. Running 'which ruby' from the command line verifies that I am using 1.8.7 with the following output: /usr/local/rvm/rubies/ree-1.8.7-2010.02/bin/ruby passenger -v prints the following: Phusion Passenger version 3.0.2 Running 'nginx -v' gives me a message that the command nginx could not be found. The server is definitely there and running as I can use nginx to serve static files, but this could have something to do with my problem. I have two users dealing with the install. root which I used to install everything, and deployer which is a user I created specifically to for deploying my applications My web app directory is in the deployer user's home directory as follows: /home/deployer/webapps/mysite.com/public Per Capistrano default deploy, a symbolic link called current is created in the public folder, and points to /home/deployer/webapps/mysite.com/public/releases/most_current_release I have chmodded the deployer directory recursively to 777 /opt/nginx permissions: rwxr-xr-x /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2 permissions: rwxrwsrwx My nginx config file has gone through just short of eternity variations, but currently looks like this: ================================================================================== worker_processes 1; events { worker_connections 1024; } http { passenger_root /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2; passenger_ruby /usr/local/rvm/bin/passenger_ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { # listen *:80; server_name mysite.com www.mysite.com; root /home/deployer/webapps/mysite.com/public/current; passenger_enabled on; passenger_friendly_error_pages on; access_log logs/mysite.com/server.log; error_log logs/mysite.com/error.log info; error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } } ================================================================================== I bounce nginx, hit the site, and boom. 403, and logs say directory index of /home/deployer... is forbidden As others with a similar problem have said, you can drop an index.html into the public/releases/current_release and it will render. But rails no worky. That's basically it. At this point I have just about completely exhausted every possible solution attempt I can think of. I am a programmer and definitely not a sysadmin, so I am 99% sure this has something to do with permissions that I have hosed, but for the life of me I just can't figure out where. If anyone can help I would really really appreciate it. If there's any specific permission things you want me to check (ie groups/permissions), can you please include the commands to do so as well. Hopefully this will help others in the future who read this post. Let me know if there is any other information I can provide, and thanks in advance!!!

  Read the article

• How can I recover an ext4 filesystem corrupted after a fsck?

  - by Regan

  I have an ext4 filesystem on luks over software raid5. The filesystem was operating "just fine" for several years when I was beginning to run out of space. I had a 9T volume on 6x2T drives. I began upgrading to 3T drives by doing the mdadm fail, remove, add, rebuild, repeat process until I had a larger array. I then grew the luks container, and then when I unmounted and tried to resize2fs I was given the message the filesystem was dirty and needed e2fsck. Without thinking I just did e2fsck -y /dev/mapper/candybox and it began spewing all kinds of inode being removed type messages (can't remember exactly) I killed e2fsck and tried to remount the filesystem to backup data I was concerned about. When trying to mount at this point I get: # mount /dev/mapper/candybox /candybox mount: wrong fs type, bad option, bad superblock on /dev/mapper/candybox, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Looking back at my older logs I noticed the filesystem was giving this error each time the machine booted: kernel: [79137.275531] EXT4-fs (dm-2): warning: mounting fs with errors, running e2fsck is recommended So shame on me for not paying attention :( I then tried to mount using every backup superblock (one after another) and each attempt left this in my log: EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 0 failed (26534!=65440) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 1 failed (38021!=36729) EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 2 failed (18336!=39845) ... EXT4-fs (dm-2): ext4_check_descriptors: Checksum for group 11911 failed (28743!=44098) BUG: soft lockup - CPU#0 stuck for 23s! [mount:2939] Attempts to restart e2fsck results in: # e2fsck /dev/mapper/candybox e2fsck 1.41.14 (22-Dec-2010) e2fsck: Group descriptors look bad... trying backup blocks... candy: recovering journal e2fsck: unable to set superblock flags on candy At this point, I decided it best to order some more drives and make an image using ddrescue Now two weeks later I have an image of the luks partition in a .img file. # ls -lh total 14T -rw-r--r-- 1 root root 14T Oct 25 01:57 candybox.img -rw-r--r-- 1 root root 271 Oct 20 14:32 candybox.logfile After numerous attempts using everything I could find online I could not coerce e2fsck to do anything on the image, so I used mkfs.ext4 -L candy candybox.img -m 0 -S and I was able to mount the dirty filesystem readonly without the journal and recover 960G of data. It gave all kinds of errors of various directories not existing and so forth but I was able to get some stuff. Which gave me some hope! I then ran e2fsck again and it had to recreate the root inode and gave a massive list of correcting group counts, I accepted the root inode creation and said no to everything else, leaving a completely empty filesystem. Re-ran again and said yes to all questions with the same result but now a "clean" but empty filesystem. extundelete gives me 0 recoverable inodes found. And now I'm stuck again, I can't come up with any other methods other than dropping to something like photorec which will give me an absolute mess with how large the filesystem was. I'm willing to re-copy the image from the original array and start over, if I can get any suggestions or ideas on a way to get more of my files back. I wish I could give more detailed logs of the commands that have run, but the output is long scrolled passed except for what gets logged to syslog and my memory is not as detailed due to the timeframe this has occurred over. Any help is greatly appreciated!

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• Hosed Windows 7 permissons

  - by Anthony

  Here is the most interesting thing I've noticed since the problems started: If I go into a control panel/system module (in this case the Resource Monitor) that has a "Check Online" type option, Firefox (my default browser) opens right up without a problem. But if I just start Firefox from any shortcuts (start menu, desktop, etc), the Firefox process starts up (and the start menu icon starts glowing) only to end without notice a few seconds later. Possibly related: If I start up in Safe-Mode (w/o Networking, but haven't tried with yet), I can start up FF or Chrome just fine, but if I attempt to open Chrome normally, I get a permissions error. Opera and Safari seem to be okay (mostly). Safari crashes when I try to download any files. All of the above leads me to believe that some (but clearly not all) core files have messed up permissions. Or rather, that I no longer have permission. System still does, based on Firefox opening without fail when the system initiates it. I've run MS Forefront once in normal mode, Malwarebytes twice in normal mode and once in safe-mode. One trojan found and deleted, but the problem persists. Two other things worth mentioning: I accidentally duplicated my library... I thought I'd try to add the "Internet" folder to my start menu, next to music and downloads. The first advanced thing I tried was "create new library". I clearly misunderstood what this means. I thought it was a way to add virtual folders to the library (which I thought, in turn, would allow me to choose it as a link on the start menu), but instead it recreated my already existing user folder, AppData and all. I didn't notice this until today. Then I tried setting permissions for my User folder to full control, recursively... Confused but not giving up,I thought I could maybe create a shortcut to the NetHood folder manually, but instead got hit with an access denied error. So I tried to change the permission levels for all sub-folders to my user folder so that I had full control. I got several access denied errors along the way. At this point I gave up, went out, ended up caught in the rain and stuck on a friend's couch and showing up late for work the next day. Thanks for nothing, Microsoft. When I finally got home today (20 hours later), I noticed that Firefox was acting really strange. I tried opening Chrome to see if the problem was client side or server side, and instead got the above-mentioned "you don't have permission to open this program" alert. And I think that's the whole story. Oh, I also did a system restore, but not chose a point from this morning (an auto update), and it worked but the problem wasn't fixed. And then all the earlier restore points were gone. So the questions are: a) is there a way to set the admin and user privs back to "default"? b) would this, in anyone's expert opinion, fix the problems I'm having? c) how come being logged in as an admin isn't the same as being logged in with admin privs? It seems that half the time I have to do run as admin for fairy standard things because i'm being treated as me-theuser and not me-theadmin. Thanks for reading.

  Read the article

• How do bots access directories on a server that are not DocumentRoot of public IP address? How do I stop them?

  - by tmsimont

  I have a local network set up with apache2 and "named" running on OpenSuse 13.1 Linux. I used the "named" service to use my computer as a domain server. I set up my router to point to ask my computer for domain lookups, so I have a chance to have it rewrite a bunch of domains on my network to its own local IP, 192.168.0.111 This works great. I use virtual host configuration to allow various domains and subdomains (re-routed to the same IP via named) to pull up different directories in my computer. For example: <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias fmb.wa.net DocumentRoot /home/work/wa.net/fmb </VirtualHost> <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias postrecord.wa.net DocumentRoot /home/work/wa.net/postrecord </VirtualHost> <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias cvalley.wa.net DocumentRoot /home/work/wa.net/cvalley_local </VirtualHost> This makes it possible for me to hit cvalley.wa.net from any device in my network and get the site that lives in /home/work/wa.net/cvalley_local I decided to forward port 80 to this computer, so I could share a few development sites with coworkers. I can't control which site they see with the same named service, because they'd have to use my computer as their domain name server... So I added a line like this: <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias MY.IP.XXX.XX DocumentRoot /home/work/wa.net/cvalley </VirtualHost> Where "MY.IP.XXX.XX" is my public IP address. This works as expected, when you hit my IP address from a public network you see the site that lives in /home/work/wa.net/cvalley. The point of confusion that I have is that there are public IP addresses in my logs in other sites. I would have expected it to be impossible to access other sites in my network, unless the public user somehow figured out what I'm calling my ServerAliases, and is mimicing my domain set up... How can public traffic be hitting my other local sites? How can I recreate this kind of access? Here are some examples of public IP's hitting my VirtualHost sites: 162.253.66.76 - - [15/Aug/2014:19:20:47 -0600] "GET /xmlrpc.php HTTP/1.0" 404 1004 "-" "-" 162.253.66.74 - - [16/Aug/2014:10:50:28 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 185.4.227.194 - - [16/Aug/2014:11:16:45 -0600] "GET http://24x7-allrequestsallowed.com/?PHPSESSID=1rysxtj500143WQMVT%5E_NAZ%5BQ HTTP/1.1" 200 262 "-" "-" 101.226.254.138 - - [16/Aug/2014:13:32:14 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 162.253.66.74 - - [16/Aug/2014:14:26:19 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 212.129.2.119 - - [16/Aug/2014:16:00:51 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 91.240.163.111 - - [16/Aug/2014:18:34:32 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 162.253.66.74 - - [16/Aug/2014:19:02:53 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 122.226.223.69 - - [17/Aug/2014:05:53:09 -0600] "GET http://www.k2proxy.com//hello.html HTTP/1.1" 404 1006 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/6.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; .NET4.0C; .NET4.0E)" ::1 - - [17/Aug/2014:10:19:26 -0600] "OPTIONS * HTTP/1.0" 200 - "-" "Apache/2.4.6 (Linux/SUSE) OpenSSL/1.0.1e PHP/5.4.20 (internal dummy connection)" 162.209.65.196 - - [17/Aug/2014:15:31:53 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 111.206.199.163 - - [18/Aug/2014:11:12:56 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 37.187.180.168 - - [18/Aug/2014:15:40:00 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 62.210.38.226 - - [18/Aug/2014:18:35:16 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" Is there anything that I can do to reliably deny public access by default, but allow it only in one VirtualHost?

  Read the article

• How to change TXSDateTime SOAP serialization in Delphi 7?

  - by LukLed

  I am trying to use Java based webservice and have soap request: <?xml version="1.0"?> <SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"> <SOAP-ENV:Body xmlns:NS1="http://something/"> <NS1:getRequest id="1"> <sessionId xsi:type="xsd:string"></sessionId> <reportType xsi:type="NS1:reportType">ALL</reportType> <xsd:dateFrom xsi:type="xsd:dateTime">2010-05-30T23:29:43.088+02:00</xsd:dateFrom> <xsd:dateTo xsi:type="xsd:dateTime">2010-05-31T23:29:43.728+02:00</xsd:dateTo> </NS1:getRequest> <parameters href="#1" /> </SOAP-ENV:Body> </SOAP-ENV:Envelope> It doesn't work, because webservice doesn't recognize dates as parameters. When I change <xsd:dateFrom xsi:type="xsd:dateTime">2010-05-30T23:29:43.088+02:00</xsd:dateFrom> <xsd:dateTo xsi:type="xsd:dateTime">2010-05-31T23:29:43.728+02:00</xsd:dateTo> to <dateFrom xsi:type="xsd:dateTime">2010-05-30T23:29:43.088+02:00</xsd:dateFrom> <dateTo xsi:type="xsd:dateTime">2010-05-31T23:29:43.728+02:00</xsd:dateTo> everything works ok, but Delphi (without Delphi source code changes) doesn't allow to change generated XML, it has only some options. Is it possible to set conversion options, so TSXDateTime is converted to <dateFrom, not <xsd:dateFrom tag? Did you meet that problem?

  Read the article

• Serialize C# dynamic object to JSON object to be consumed by javascript

  - by Jeff Jin

  Based on the example c# dynamic with XML, I modified DynamicXml.cs and parsed my xml string. the modified part is as follows public override bool TryGetMember(GetMemberBinder binder, out object result) { result = null; if (binder.Name == "Controls") result = new DynamicXml(_elements.Elements()); else if (binder.Name == "Count") result = _elements.Count; else { var attr = _elements[0].Attribute( XName.Get(binder.Name)); if (attr != null) result = attr.Value; else { var items = _elements.Descendants( XName.Get(binder.Name)); if (items == null || items.Count() == 0) return false; result = new DynamicXml(items); } } return true; } The xml string to parse: "< View runat='server' Name='Doc111'>" + "< Caption Name='Document.ConvertToPdf' Value='Allow Conversion to PDF'></ Caption>" + "< Field For='Document.ConvertToPdf' ReadOnly='False' DisplayAs='checkbox' EditAs='checkbox'></ Field>" + "< Field For='Document.Abstract' ReadOnly='False' DisplayAs='label' EditAs='textinput'></ Field>" + "< Field For='Document.FileName' ReadOnly='False' DisplayAs='label' EditAs='textinput'></ Field>" + "< Field For='Document.KeyWords' ReadOnly='False' DisplayAs='label' EditAs='textinput'></ Field>" + "< FormButtons SaveCaption='Save' CancelCaption='Cancel'></ FormButtons>" + "</ View>"; dynamic form = new DynamicXml(markup_fieldsOnly); is there a way to serialize the content of this dynamic object(name value pairs inside dynamic) form as JSON object and sent to client side(browser)?

  Read the article

• Negative ItemCount in SharePoint Document Library

  - by ccomet

  What can be done about negative numbers in library item counts? ItemCount is a read-only property, what are you supposed to do when it is drastically incorrect? Earlier last week, I was doing some testing involving the copying and moving of files and folders from one document library to another. I was transfering the items from our actual document library to a sandbox "Test" library that I used to run all sorts of object model and workflow testing in before migrating to the public lists and libraries. I noticed that with files, things worked correctly, but when I copied a folder that had a file inside it (using SPFolder.CopyTo()), the item count for the test library did not actually update. Since this testing was mostly playing around, I paid it little heed. Today I was back in the test library to test a different workflow (regarding PDF conversion). While I was there, I decided to delete the folder I left last week since I didn't need it anymore. And that's when I saw the item count for the list drop to -1 in the All Site Content View. When I deleted the new PDF I had just uploaded, it then dropped to -2! I even checked with the object model... getting an instance of the library I checked the ItemCount property... lo and behold it was also -2. Is there any process which runs in the background, kinda like the one that cleans up workflow history, which will correct this kind of issue? Or is a programmer expected to keep watch for this kind of situation and come up with calculations to compensate the "count penalty", as it were?

  Read the article

• How do I filter out NaN FLOAT values in Teradata SQL?

  - by Paul Hooper

  With the Teradata database, it is possible to load values of NaN, -Inf, and +Inf into FLOAT columns through Java. Unfortunately, once those values get into the tables, they make life difficult when writing SQL that needs to filter them out. There is no IsNaN() function, nor can you "CAST ('NaN' as FLOAT)" and use an equality comparison. What I would like to do is, SELECT SUM(VAL**2) FROM DTM WHERE NOT ABS(VAL) > 1e+21 AND NOT VAL = CAST ('NaN' AS FLOAT) but that fails with error 2620, "The format or data contains a bad character.", specifically on the CAST. I've tried simply "... AND NOT VAL = 'NaN'", which also fails for a similar reason (3535, "A character string failed conversion to a numeric value."). I cannot seem to figure out how to represent NaN within the SQL statement. Even if I could represent NaN successfully in an SQL statement, I would be concerned that the comparison would fail. According to the IEEE 754 spec, NaN = NaN should evaluate to false. What I really seem to need is an IsNaN() function. Yet that function does not seem to exist.

  Read the article

• VS2008 -> VS2010 leads to cryptic STL errors

  - by Jakobud

  The following C++ library was successfully compiled in VS2008 http://sourceforge.net/projects/xmlrpcc4win/files/xmlrpcc4win/XmlRpcC4Win1.0.8.zip/download When I open it in VS2010, it goes through the conversion wizard process without any errors. Now, when I attempt to compile it in VS2010, I get some weird STL errors like these: 1>TimXmlRpc.cpp(1018): error C2039: 'back_insert_iterator' : is not a member of 'std' 1>TimXmlRpc.cpp(1018): error C2065: 'back_insert_iterator' : undeclared identifier 1>TimXmlRpc.cpp(1018): error C2275: 'XmlRpcValue::BinaryData' : illegal use of this type as an expression 1>TimXmlRpc.cpp(1018): error C2065: 'ins' : undeclared identifier 1>TimXmlRpc.cpp(1018): error C2039: 'back_inserter' : is not a member of 'std' 1>TimXmlRpc.cpp(1018): error C3861: 'back_inserter': identifier not found 1>TimXmlRpc.cpp(1019): error C2065: 'ins' : undeclared identifier 1>TimXmlRpc.cpp(1031): error C2039: 'back_insert_iterator' : is not a member of 'std' 1>TimXmlRpc.cpp(1031): error C2065: 'back_insert_iterator' : undeclared identifier 1>TimXmlRpc.cpp(1031): error C2275: 'std::vector<_Ty>' : illegal use of this type as an expression 1> with 1> [ 1> _Ty=char 1> ] 1>TimXmlRpc.cpp(1031): error C2065: 'ins' : undeclared identifier 1>TimXmlRpc.cpp(1031): error C2039: 'back_inserter' : is not a member of 'std' 1>TimXmlRpc.cpp(1031): error C3861: 'back_inserter': identifier not found 1>TimXmlRpc.cpp(1032): error C2065: 'ins' : undeclared identifier I'm not sure what to make of some of these. For instance, back_insert_iterator is in fact a member of std, but VS doesn't seem to think it is. How do I fix errors like these? They just don't seem to make much sense so I'm not sure where to begin. Perhaps its something in my project settings? For example, here is line 1018, which gives the std error: std::back_insert_iterator<BinaryData> ins = std::back_inserter(*(u.asBinary)); If anyone could give me some direction I'd appreciate it. I'm new enough to C++ that I'm having a tough time figuring out this one.

  Read the article

< Previous Page | 430 431 432 433 434 435 436 437 438 439 440 441  | Next Page >