Search Results

Search found 11124 results on 445 pages for 'optical drive'.

Page 436/445 | < Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >

• Splitting a raidctl mirror safely

  - by milkfilk

  I have a Sun T5220 server with the onboard LSI card and two disks that were in a RAID 1 mirror. The data is not important right now but we had a failed disk and are trying to understand how to do this for real if we had to recover from a failure. The initial situation looked like this: # raidctl -l c1t0d0 Volume Size Stripe Status Cache RAID Sub Size Level Disk ---------------------------------------------------------------- c1t0d0 136.6G N/A DEGRADED OFF RAID1 0.1.0 136.6G GOOD N/A 136.6G FAILED Green light on the 0.0.0 disk. Find / lights up the 0.1.0 disk. So I know I have a bad drive and which one it is. Server still boots obviously. First, we tried putting a new disk in. This disk came from an unknown source. Format would not see it, cfgadm -al would not see it so raidctl -l would not see it. I figure it's bad. We tried another disk from another spare server: # raidctl -c c1t1d0 c1t0d0 (where t1 is my good disk - 0.1.0) Disk has occupied space. Also the different syntax options don't change anything: # raidctl -C "0.1.0 0.0.0" -r 1 1 Disk has occupied space. # raidctl -C "0.1.0 0.0.0" 1 Disk has occupied space. Ok. Maybe this is because the disk from the spare server had a RAID 1 on it already. Aha, I can see another volume in raidctl: # raidctl -l Controller: 1 Volume:c1t1d0 (this is my server's root mirror) Volume:c1t132d0 (this is the foreign root mirror) Disk: 0.0.0 Disk: 0.1.0 ... No problem. I don't care about the data, I'll just delete the foreign mirror. # raidctl -d c1t132d0 (warning about data deletion but it works) At this point, /usr/bin/ binaries freak out. By that I mean, ls -l /usr/bin/which shows 1.4k but cat /usr/bin/which gives me a newline. Great, I just blew away the binaries (ie: binaries in mem still work)? I bounce the box. It all comes back fine. WTF. Anyway, back to recreating my mirror. # raidctl -l Controller: 1 Volume:c1t1d0 (this is my server's root mirror) Disk: 0.0.0 Disk: 0.1.0 ... Man says that you can delete a mirror and it will split it. Ok, I'll delete the root mirror. # raidctl -d c1t0d0 Array in use. (this might not be the exact error) I googled this and found of course you can't do this (even with -f) while booted off the mirror. Ok. I boot cdrom -s and deleted the volume. Now I have one disk that has a type of "LSI-Logical-Volume" on c1t1d0 (where my data is) and a brand new "Hitachi 146GB" on c1t0d0 (what I'm trying to mirror to): (booted off the CD) # raidctl -c c1t1d0 c1t0d0 (man says it's source destination for mirroring) Illegal Array Layout. # raidctl -C "0.1.0 0.0.0" -r 1 1 (alt syntax per man) Illegal Array Layout. # raidctl -C "0.1.0 0.0.0" 1 (assumes raid1, no help) Illegal Array Layout. Same size disks, same manufacturer but I did delete the volume instead of throwing in a blank disk and waiting for it to resync. Maybe this was a critical error. I tried selecting the type in format for my good disk to be a plain 146gb disk but it resets the partition table which I'm pretty sure would wipe the data (bad if this was production). Am I boned? Anyone have experience with breaking and resyncing a mirror? There's nothing on Google about "Illegal Array Layout" so here's my contrib to the search gods.

  Read the article

• Permissions restoring from Time Machine - Finder copy vs "cp" copy

  - by Ben Challenor

  Note: this question was starting to sprawl so I rewrote it. I have a folder that I'm trying to restore from a Time Machine backup. Using cp -R works fine, but certain folders cannot be restored with either the Time Machine UI or Finder. Other users have reported similar errors and the cp -R workaround was suggested (e.g. Restoring from Time Machine - Permissions Error). But I wanted to understand: Why cp -R works when the Finder and the Time Machine UI do not. Whether I could prevent the errors by changing file permissions before the backup. There do indeed seem to be some permissions that Finder works with and some that it does not. I've narrowed the errors down to folders with the user ben (that's me) and the group wheel. Here's a simplified reproduction. I have four folders with the owner/group combinations I've seen so far: ben ~/Desktop/test $ ls -lea total 16 drwxr-xr-x 7 ben staff 238 27 Nov 14:31 . drwx------+ 17 ben staff 578 27 Nov 14:29 .. 0: group:everyone deny delete -rw-r--r--@ 1 ben staff 6148 27 Nov 14:31 .DS_Store drwxr-xr-x 3 ben staff 102 27 Nov 14:30 ben-staff drwxr-xr-x 3 ben wheel 102 27 Nov 14:30 ben-wheel drwxr-xr-x 3 root admin 102 27 Nov 14:31 root-admin drwxr-xr-x 3 root wheel 102 27 Nov 14:31 root-wheel Each contains a single file called file with the same owner/group: ben ~/Desktop/test $ cd ben-staff ben ~/Desktop/test/ben-staff $ ls -lea total 0 drwxr-xr-x 3 ben staff 102 27 Nov 14:30 . drwxr-xr-x 7 ben staff 238 27 Nov 14:31 .. -rw-r--r-- 1 ben staff 0 27 Nov 14:30 file In the backup, they look like this: ben /Volumes/Deimos/Backups.backupdb/Ben’s MacBook Air/Latest/Macintosh HD/Users/ben/Desktop/test $ ls -leA total 16 -rw-r--r--@ 1 ben staff 6148 27 Nov 14:34 .DS_Store 0: group:everyone deny write,delete,append,writeattr,writeextattr,chown drwxr-xr-x@ 3 ben staff 102 27 Nov 14:51 ben-staff 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 ben wheel 102 27 Nov 14:51 ben-wheel 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 root admin 102 27 Nov 14:52 root-admin 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 root wheel 102 27 Nov 14:52 root-wheel 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown Of these, ben-staff can be restored with Finder without errors. root-wheel and root-admin ask for my password and then restore without errors. But ben-wheel does not prompt for my password and gives the error: The operation can’t be completed because you don’t have permission to access “file”. Interestingly, I can restore the file from this folder by dragging it directly to my local drive (instead of dragging its parent folder), but when I do so its permissions are changed to ben/staff. Here are the permissions after the restore for the three folders that worked correctly, and the file from ben-wheel that was changed to ben/staff. ben ~/Desktop/test-restore $ ls -leA total 16 -rw-r--r--@ 1 ben staff 6148 27 Nov 14:46 .DS_Store drwxr-xr-x 3 ben staff 102 27 Nov 14:30 ben-staff -rw-r--r-- 1 ben staff 0 27 Nov 14:30 file drwxr-xr-x 3 root admin 102 27 Nov 14:31 root-admin drwxr-xr-x 3 root wheel 102 27 Nov 14:31 root-wheel Can anyone explain this behaviour? Why do Finder and the Time Machine UI break with the ben / wheel permissions? And why does cp -R work (even without sudo)?

  Read the article

• Useful Command-line Commands on Windows

  - by Sung Meister

  The aim for this Wiki is to promote using a command to open up commonly used applications without having to go through many mouse clicks - thus saving time on monitoring and troubleshooting Windows machines. Answer entries need to specify Application name Commands Screenshot (Optional) Shortcut to commands && - Command Chaining %SYSTEMROOT%\System32\rcimlby.exe -LaunchRA - Remote Assistance (Windows XP) appwiz.cpl - Programs and Features (Formerly Known as "Add or Remove Programs") appwiz.cpl @,2 - Turn Windows Features On and Off (Add/Remove Windows Components pane) arp - Displays and modifies the IP-to-Physical address translation tables used by address resolution protocol (ARP) at - Schedule tasks either locally or remotely without using Scheduled Tasks bootsect.exe - Updates the master boot code for hard disk partitions to switch between BOOTMGR and NTLDR cacls - Change Access Control List (ACL) permissions on a directory, its subcontents, or files calc - Calculator chkdsk - Check/Fix the disk surface for physical errors or bad sectors cipher - Displays or alters the encryption of directories [files] on NTFS partitions cleanmgr.exe - Disk Cleanup clip - Redirects output of command line tools to the Windows clipboard cls - clear the command line screen cmd /k - Run command with command extensions enabled color - Sets the default console foreground and background colors in console command.com - Default Operating System Shell compmgmt.msc - Computer Management control.exe /name Microsoft.NetworkAndSharingCenter - Network and Sharing Center control keyboard - Keyboard Properties control mouse(or main.cpl) - Mouse Properties control sysdm.cpl,@0,3 - Advanced Tab of the System Properties dialog control userpasswords2 - Opens the classic User Accounts dialog desk.cpl - opens the display properties devmgmt.msc - Device Manager diskmgmt.msc - Disk Management diskpart - Disk management from the command line dsa.msc - Opens active directory users and computers dsquery - Finds any objects in the directory according to criteria dxdiag - DirectX Diagnostic Tool eventvwr - Windows Event Log (Event Viewer) explorer . - Open explorer with the current folder selected. explorer /e, . - Open explorer, with folder tree, with current folder selected. F7 - View command history find - Searches for a text string in a file or files findstr - Find a string in a file firewall.cpl - Opens the Windows Firewall settings fsmgmt.msc - Shared Folders fsutil - Perform tasks related to FAT and NTFS file systems ftp - Transfers files to and from a computer running an FTP server service getmac - Shows the mac address(es) of your network adapter(s) gpedit.msc - Group Policy Editor gpresult - Displays the Resultant Set of Policy (RSoP) information for a target user and computer httpcfg.exe - HTTP Configuration Utility iisreset - To restart IIS InetMgr.exe - Internet Information Services (IIS) Manager 7 InetMgr6.exe - Internet Information Services (IIS) Manager 6 intl.cpl - Regional and Language Options ipconfig - Internet protocol configuration lusrmgr.msc - Local Users and Groups Administrator msconfig - System Configuration notepad - Notepad? ;) mmsys.cpl - Sound/Recording/Playback properties mode - Configure system devices more - Displays one screen of output at a time mrt - Microsoft Windows Malicious Software Removal Tool mstsc.exe - Remote Desktop Connection nbstat - displays protocol statistics and current TCP/IP connections using NBT ncpa.cpl - Network Connections netsh - Display or modify the network configuration of a computer that is currently running netstat - Network Statistics net statistics - Check computer up time net stop - Stops a running service. net use - Connects a computer to or disconnects a computer from a shared resource, or displays information about computer connections odbcad32.exe - ODBC Data Source Administrator pathping - A traceroute that collects detailed packet loss stats perfmon - Opens Reliability and Performance Monitor ping - Determine whether a remote computer is accessible over the network powercfg.cpl - Power management control panel applet quser - Display information about user sessions on a terminal server qwinsta - See disconnected remote desktop sessions reg.exe - Console Registry Tool for Windows regedit - Registry Editor rasdial - Connects to a VPN or a dialup network robocopy - Backup/Restore/Copy large amounts of files reliably rsop.msc - Resultant Set of Policy (shows the combined effect of all group policies active on the current system/login) runas - Run specific tools and programs with different permissions than the user's current logon provides sc - Manage anything you want to do with services. schtasks - Enables an administrator to create, delete, query, change, run and end scheduled tasks on a local or remote system. secpol.msc - Local Security Settings services.msc - Services control panel set - Displays, sets, or removes cmd.exe environment variables. set DIRCMD - Preset dir parameter in cmd.exe start - Starts a separate window to run a specified program or command start. - opens the current directory in the Windows Explorer. shutdown.exe - Shutdown or Reboot a local/remote machine subst.exe - Associates a path with a drive letter, including local drives systeminfo -Displays a comprehensive information about the system taskkill - terminate tasks by process id (PID) or image name tasklist.exe - List Processes on local or a remote machine taskmgr.exe - Task Manager telephon.cpl - Telephone and Modem properties timedate.cpl - Date and Time title - Change the title of the CMD window you have open tracert - Trace route wmic - Windows Management Instrumentation Command-line winver.exe - Find Windows Version wscui.cpl - Windows Security Center wuauclt.exe - Windows Update AutoUpdate Client

  Read the article

• Unauthorized Access Exception using Web Deploy to Site when the site root is a UNC path

  - by Peter LaComb Jr.

  I am trying to use Web Deploy to deploy a site where the Site is rooted on a UNC path instead of a local drive. This is because I want to have a shared configuration, and have all servers point to the same UNC for content. That would allow me to deploy to one server and have all servers updated at the same time. I've created a share with everyone and users read/write. The NTFS permissions have the ID of the appDomain account as full control, and that is the same account that is configured as the specific user in Management Service Delegation. I can log on to the destination server as that ID, access the share and create/delete files. However, I'm getting the following exception in my Microsoft Web Deploy log on the destination server: User: Client IP: 192.168.62.174 Content-Type: application/msdeploy Version: 9.0.0.0 MSDeploy.VersionMin: 7.1.600.0 MSDeploy.VersionMax: 9.0.1631.0 MSDeploy.Method: Sync MSDeploy.RequestId: c060c823-cdb4-4abe-8294-5ffbdc327d2e MSDeploy.RequestCulture: en-US MSDeploy.RequestUICulture: en-US ServerVersion: 9.0.1631.0 Skip: objectName="^configProtectedData$" Provider: auto, Path: A tracing deployment agent exception occurred that was propagated to the client. Request ID 'c060c823-cdb4-4abe-8294-5ffbdc327d2e'. Request Timestamp: '8/23/2012 11:01:56 AM'. Error Details: ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER Microsoft.Web.Deployment.DeploymentDetailedUnauthorizedAccessException: Unable to perform the operation ("Create Directory") for the specified directory ("\someserver.mydomain.local\sharename\sitename\applicationName"). This can occur if the server administrator has not authorized this operation for the user credentials you are using. Learn more at: http://go.microsoft.com/fwlink/?LinkId=221672#ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER. --- Microsoft.Web.Deployment.DeploymentException: The error code was 0x80070005. --- System.UnauthorizedAccessException: Access to the path '\someserver.mydomain.local\sharename\sitename\applicationName' is denied. at Microsoft.Web.Deployment.NativeMethods.RaiseIOExceptionFromErrorCode(Win32ErrorCode errorCode, String maybeFullPath) at Microsoft.Web.Deployment.DirectoryEx.CreateDirectory(String path) at Microsoft.Web.Deployment.DirPathProviderBase.CreateDirectory(String fullPath, DeploymentObject source) at Microsoft.Web.Deployment.DirPathProviderBase.Add(DeploymentObject source, Boolean whatIf) --- End of inner exception stack trace --- --- End of inner exception stack trace --- at Microsoft.Web.Deployment.FilePathProviderBase.HandleKnownRetryableExceptions(DeploymentBaseContext baseContext, Int32[] errorsToIgnore, Exception e, String path, String operation) at Microsoft.Web.Deployment.DirPathProviderBase.Add(DeploymentObject source, Boolean whatIf) at Microsoft.Web.Deployment.DeploymentObject.Add(DeploymentObject source, DeploymentSyncContext syncContext) at Microsoft.Web.Deployment.DeploymentSyncContext.HandleAdd(DeploymentObject destObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentSyncContext.HandleUpdate(DeploymentObject destObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenNoOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenNoOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.ProcessSync(DeploymentObject destinationObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentObject.SyncToInternal(DeploymentObject destObject, DeploymentSyncOptions syncOptions, PayloadTable payloadTable, ContentRootTable contentRootTable, Nullable1 syncPassId) at Microsoft.Web.Deployment.DeploymentAgent.HandleSync(DeploymentAgentAsyncData asyncData, Nullable1 passId) at Microsoft.Web.Deployment.DeploymentAgent.HandleRequestWorker(DeploymentAgentAsyncData asyncData) at Microsoft.Web.Deployment.DeploymentAgent.HandleRequest(DeploymentAgentAsyncData asyncData) This is shown as the following on the console of the machine where I run the deployment: C:\Users\PLaComb"C:\Program Files (x86)\IIS\Microsoft Web Deploy V3\msdeploy.exe" -source:package='C:\Packages\Deployments\applicationName.zip' -dest:auto,computerName='https://SERVERNAME:8172/msdeploy.axd',includeAcls='True' -verb:sync -disableLink:AppPoolExtension -disableLink:ContentExtension -disableLink:CertificateExtension -setParamFile:"C:\Packages\Deployments\applicationName.SetParameters.xml" -allowUntrusted Info: Using ID 'c060c823-cdb4-4abe-8294-5ffbdc327d2e' for connections to the remote server. Info: Adding sitemanifest (sitemanifest). Info: Adding virtual path (JMS/admin) Info: Adding directory (JMS/admin). Error Code: ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER More Information: Unable to perform the operation ("Create Directory") for the specified directory ("\someserver.mydomain.local\sharename\sitename\applicationName"). This can occur if the server administrator has not authorized this operation for the user credentials you are using. Learn more at: http://go.microsoft.com/fwlink/?LinkId=221672#ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER. Error: The error code was 0x80070005. Error: Access to the path '\someserver.mydomain.local\sharename\sitename\applicationName' is denied. Error count: 1.

  Read the article

• Why do GPUs overheat?

  - by JAD

  About a year ago, I added a 9800GT (1 GB version) and a Corsair CX500 PSU to an HP M8000N computer. A few weeks ago, the HDD overheated and I decided to transfer the GPU & PSU to a new build, which consists of: i3 @ 3.3Ghz Gigabyte H61 Micro ATX Mobo 4GB RAM 500GB WD HDD DVD RW Drive Cooler Master Elite 430 Tower Once I had Win7 up and running, I installed all the essential drivers that came with the Gigabyte Mobo CD. However, whenever I tried installing the Graphics Media Accelerator driver, the computer would crash and enter an endless boot sequence on the next startup. I skipped installing this driver and installed the CD driver for the 9800GT, which by now is a year old. Everything was working fine, WEI rated my GPU at 6.6 graphics & aero performance. However, after updating my Nvidia drivers to the latest, the WEI dropped my rating to 3.3 for Aero, and 4.7 for graphics performance. Just to make sure that everything was ok, I ran Bad Company 2 on medium settings. The first few minutes ran just fine at a smooth framerate, so I dismissed this as Windows being Windows. About 6 hours later, I ran BC2 again. This time I averaged anywhere from 2-5 FPS. I checked the GPU temperature through GPU-Z, and it came back as 120C. The problem with this, is that the computer was on for six hours up to that point. Wouldn't the card have experienced a reactor core meltdown a lot sooner than that? Granted, the computer was "sleeping" some of the time, but still... The next day I took out a temperature gun and ran some tests. I would point the laser at a very specific area on the reverse side of the card (not the fan or "front"), and compare the temp reading with GPU-Z. After leaving the system on idle on idle for a few minutes, I ran BC2 twice. Here are the results: GPU-Z Reading / Temp Gun Reading / Time Null / 22.3°C / Comp is Off 53°C / 33.5°C / 1:49 78°C / 46°C / 1:53 - (First BC2 run; good framerate) 102°C / 64.6°C / 2:01 - (System is again on idle) 113°C / 64.8°C / 2:10 119°C / 71.8°C / 2:17 - (Second BC2 run; poor framerate) I should also mention that I also took a temp recording of another part of the GPU from 2:01-2:17. The temp in this area jumped from 75°C to 82.9°C in that time frame. This pretty much confirms that GPU-Z is reporting the temperature accurately, and the card is overheating. But I'd like to know why; the cars is doing nothing and still the temperature climbs at a steady rate. I thoroughly cleaned the GPU and PSU when I salvaged them from the old HP M8000N computer with a can of compressed air, dust cant be the issue. Similarly, the rest of the computer is brand new. I installed various Nvidia drivers, but no luck. It seems strange to me that a year-old card is suddenly failing on me; aren't they supposed to last at least two years? Could this be a driver issue? Is the motherboard faulty? Could the PSU be overfeeding the card on voltage? Neither case seems likely, as the CPU, RAM and otherwise the rest of the comp has worked flawlessly and has stayed well within respectable temp ranges (the i3 lingers around 50C, the HDD stays at 30C, so does the PSU). How can I pinpoint the issue?

  Read the article

• Graphics card initialisation problems when booting - requires a "double" boot

  - by DMA57361

  Problem Outline When booting from cold (and my machine is disconnected from main power when off, but leaving it connected doesn't help) the graphics card (single PCI-e card GeForce 460) will not initialise on the first boot, leaving me with the motherboards on-board graphics (which kick in automatically if no PCI-e card is found). However, if I restart the computer - normally I do this by powering it off just after the numlock lights up on the keyboard (ie, just after POST/BIOS and before Windows takes over), wait for the system to whirr down, and power up again - the graphics card will work correctly. Once double-booted in this matter the system seems to work correctly - with no noticeable problems. This is reproducible every time I try to boot - it has been working like this for about a month now. Background Information Sept 2010 - I suffered a hardware malfunction (crashes in Windows and graphics corruption on BIOS screens). By way of spare hardware I determined that replacing the PSU removed the issue, so I replaced the PSU with a brand new one of slightly higher power (460W replaced with 500W). Oct 2010 - The problem resurfaced. I purchased a new graphics card (GeForce 460), which removed the problem. The new graphics card immediately started having the boot initialisation problems mentioned. I presumed there was a motherboard fault all along, but because the system worked once booted, and I was temporarily out of spare money, I left the system alone and continued to use it. Early/Mid Dec 2010 - In the space of 5 days I recieved 3 instances of hard drive corruption (seemlingly fixed by chkdsk and sfc in each case...). Since I was already under the impression the motherboard was faulty, I purchased a new one ASAP, this also required new RAM (as I dropped from 4 slots to 2 and didn't want to drop mem quantity). Past 3-4 weeks - With a brand new PSU, Graphics Card, Motherboard and RAM I'm suffering the problem outlined above. So, what could be causing this and how do I can resolve it? Additional Notes Once double-booted the system seems to work entirely correctly. The graphics card problem has occured on two entirely different motherboards. I do not have the opportunity to test the graphics card in a different computer (I've only the old motherboard, which is dubious, or a really old desktop that still has an AGP port). Under load (ie, modern games for long enough for temperatures to plateau) the system remains stable and performs as expected. The software that came with the new motherboard and SpeenFan both report all voltages and temperatures are within nominal bounds, when idle and when under load. I've looking over the BIOS settings for my motherboard multiple times and can find nothing that helps. This system is configured to run with everything at standard levels - no overclocking. I've tried booting the system with only the mobo and graphics card connected (thinking maybe my new PSU was too weak for the new gfx card, even though it meets the quoted PSU requirements for the card) but the same problem persists (and really if the PSU was weak I'd have problems with the system under load). When the gfx card does not initialise the fan on its cooling unit is running, possibly slower than otherwise - but this measurement is by eye and so unreliable.

  Read the article

• Lag spikes at full CPU usage, lagy mouse, maybe video card

  - by Roberts

  My PC specs: Motherboard Name - Gigabyte GA-945PL-S3 CPU Type - DualCore Intel Core 2 Duo E4300, 1800 MHz (9 x 200) OS - Microsoft Windows 7 Ultimate OS Kernel Type - 32-bit OS Version - 6.1.7601 I bougth a new video card one month ago. GeForce 210. I didn't have any problems. I wanted to overclock it, in other words: "Play with it". So I installed Gigabyte EasyBoost from CD and overclocked the GPU 590 + 110 mhz, memory to max to 960mhz from 800mhz. Benchmarks showed a little bit bigger score. Then I overclocked shader clock from 1405 to [..] (don't remeber really). So I was playing Modern Warfare 2 when off sudden computer froze when I wanted to select team, I was afk before that. I had to reset CMOS. After that I had problems with Skype: unread messages and no sound. Then I figured it out that when ever I open EasyBoost - Skype starts to glitch again. Now I use EVGA Precission X. Now after a month, I cleaned computer and closed the case, it was open all the time. I started to overclock GPU clock only (just a bit) because there was no problems that would stop me. So sometimes on heavy CPU load graphics starts to lag. Dragging a window is painful to watch too. Sometimes the screen freezes for 5 to 10 seconds (I can see that hard disk activity is maximal). You may say that CPU fault it is, isn't it? But sometimes lag spikes starts randomly when CPU load is at maximum. All 3 benchmark softwares (PerformanceTest, NovaBench and MSI Kombustor) shows that performance of my video card has dropped about 25%. BUT! CPU score is lower too. I ignored these problems but when I refreshed Windows Experience Index I was shocked. Month before (in latvian language but not so hard to understand): Now 01.04.2012 (upgraded RAM): This happened when I tried to capture Minecraft with Fraps on underclocked GPU to 580mhz (def: 590mhz): All drivers are up to date. Average CPU temperature from 55°C to 75°C (at 70°C sometimes starts these lag spikes). Video card's tempratures are from 45°C to 60°C (very hard to reach 60°C). So my hope is that the video card is fine, cause this card is very new and I want to upgrade CPU anyways. Aplogies for my mistakes in vocabulary (I am trying to type this as fast I can). Update 02.04.2012 - 7:21 Forgot one thing, my hard disk is extrimly slow and I will upgrade it this week or next week so I will be installing same OS again. I am multi-tasker but I can't do much because of 1.8 GHz CPU and slow hard drive (Model ID - WDC WD800JD-60JRC0). The Windows Experience Index is back to normal. Actually "Spelu grafika" (Gaming graphics) are higher than month ago. During this test mouse was very lagy, but month ago there weren't any problems. WHY!?

  Read the article

• How to publish an ASP.NET MVC application to a free host

  - by Lirik

  Hi, I'm using a free web host (0000free) which supports ASP.NET MVC, but it uses Mono. This is the first time I deploy an MVC application, so I'm a little confused as to where I need to deploy it. I have Visual Studio 2010 and I used its Publish Feature (i.e. right click on the project name and click publish) and I tried several things: Publish method: FTP to the root folder. Publish method: FTP to the publich_html folder. Publish method: File System to the root folder. Publish method: File System to the publich_html folder. Publish method: File System to a local directory on my computer and then FTP to root and also tried the public_html folder. I went into the cPanel (control panel) to try and see if ASP.NET has to be added/enabled for my web site, but I didn't see anything there. I can't browse to Index.aspx nor can I redirect to it from index.html (as suggested from other posts on the host forum), right now I have a link from index.html to Index.aspx but it's not working either (see http://www.mydevarmy.com) I've also tried renaming Index.aspx to Default.aspx, but that doesn't work either. The search utility of the forum of the host is somewhat weak, so I use google to search their forum: http://www.google.com/search?q=publish+asp.net+site%3A0000free.com%2Fforum%2F&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a I've been reading Pro ASP.NET MVC Framework and they have a chapter about publishing, but it doesn't provide any specific information with respect to the location of publishing, this is all they say (and it's not very helpful in my case): Where Should I Put My Application? You can deploy your application to any folder on the server. When IIS first installs, it automatically creates a folder for a web site called Default Web Site at c:\Inetpub\wwwroot\, but you shouldn’t feel any obligation to put your application files there. It’s very common to host applications on a different physical drive from the operating system (e.g., in e:\websites\ example.com). It’s entirely up to you, and may be influenced by concerns such as how you plan to back up the server. Here is the exception I get when I try to view my Index.aspx page: Unrecognized attribute 'targetFramework'. (/home/devarmy/public_html/Web.config line 1) Description: HTTP 500. Error processing request. Stack Trace: System.Configuration.ConfigurationErrorsException: Unrecognized attribute 'targetFramework'. (/home/devarmy/public_html/Web.config line 1) at System.Configuration.ConfigurationElement.DeserializeElement (System.Xml.XmlReader reader, Boolean serializeCollectionKey) [0x00000] in <filename unknown>:0 at System.Configuration.ConfigurationSection.DoDeserializeSection (System.Xml.XmlReader reader) [0x00000] in <filename unknown>:0 at System.Configuration.ConfigurationSection.DeserializeSection (System.Xml.XmlReader reader) [0x00000] in <filename unknown>:0 at System.Configuration.Configuration.GetSectionInstance (System.Configuration.SectionInfo config, Boolean createDefaultInstance) [0x00000] in <filename unknown>:0 at System.Configuration.ConfigurationSectionCollection.get_Item (System.String name) [0x00000] in <filename unknown>:0 at System.Configuration.Configuration.GetSection (System.String path) [0x00000] in <filename unknown>:0 at System.Web.Configuration.WebConfigurationManager.GetSection (System.String sectionName, System.String path, System.Web.HttpContext context) [0x00000] in <filename unknown>:0 at System.Web.Configuration.WebConfigurationManager.GetSection (System.String sectionName, System.String path) [0x00000] in <filename unknown>:0 at System.Web.Configuration.WebConfigurationManager.GetWebApplicationSection (System.String sectionName) [0x00000] in <filename unknown>:0 at System.Web.Compilation.BuildManager.get_CompilationConfig () [0x00000] in <filename unknown>:0 at System.Web.Compilation.BuildManager.Build (System.Web.VirtualPath vp) [0x00000] in <filename unknown>:0 at System.Web.Compilation.BuildManager.GetCompiledType (System.Web.VirtualPath virtualPath) [0x00000] in <filename unknown>:0 at System.Web.Compilation.BuildManager.GetCompiledType (System.String virtualPath) [0x00000] in <filename unknown>:0 at System.Web.HttpApplicationFactory.InitType (System.Web.HttpContext context) [0x00000] in <filename unknown>:0

  Read the article

• RAID and Partitions, guidance Needed

  - by beauregarde

  Alright I have a Biostar TA790GX3A2+ Mobo 2x Seagate 750Gb Hard drive (with 2 different speeds) an X4 9750 A GeForce 9800GT and 2GB RAM Hardware Specs link text I want to configure my computer with partitions in various RAID arrays. The Partitions I know i want (disk letters are mostly for reference here) C: XP Boot D: XP Swap E: XP Run F: Games G: Data The Partitions I think I want (repeat caveat) H: small FAT for Win Legacy and DOS I: Linux J: Linux Swap K-?M?: Other Linux /whatever partitions N & O: Attic for D1 and D2 What I'd like to do, is have C: written on Disk 1 (D1),.. D: on D2,.. E: and F: striped on D1 & D2,.. G: mirrored or D1 & D2,.. I: on D2 (so i can just switch disc boot priority to open in Ubuntu),.. J: on D1,.. and H: somewhere low on D1 I am inexperienced with VMs, so i am unsure as to whether those run out of XP, or whether i need to reserve a primary partition for them. However, I think they would be preferable for testing new OS's to scheduling a partition for the same purpose. I'm also not married to XP, but -64 IS pretty important to me. QUestion Time 1) Ignoring the irrationality of it all, is such a configuration possible? If not, can some pseudo-approximation be achieved? 2) My RAID is software, isnt it? 3) How much should I short a 750GB HD? And should i use that space for my attics, or for my attics and something else, or for something else (.iso's perhaps?)? 4) if XP is striped on D1 & D2, will that interfere egregiously with my Swap writes on D2? If so, would striping both XP and Swap relieve (or at least mitigate) that issue? Should XP and Swap just be written normally on 2 different HDs? 5) Should I keep DL's and Drivers on E: (XP Run), F: (Games), or elsewhere? 6) Is 4GB enough for C:? 7) Is 30GB enough (or too much) for E:? 8) How much to reserve for the Linux and sub-Linux partitions? Also, where on the platter do you think i should put them? 9) Am I a fool to use FAT16 instead of FAT32 for H: because I'd rather run 95 than 98SE? If not, do you think 2GB or 4GB? 10) I cant predict what my Max Commit Charge will be, so recommendations for Pagefile size? 5GB? 12GB? 11) VMs, where do I run them? do they exacerbate anything? Would it be better to just emulate Linux, 95, and DOS? EC) What havent I considered that I really should? Notes: computer is mostly for playing games and watching media, though I wouldnt rule out the use of particularly blah-intensive anything.

  Read the article

• Bash can't start a programme that's there and has all the right permissions

  - by Rory

  This is a gentoo server. There's a programme prog that can't execute. (Yes the execute permission is set) About the file $ ls prog $ ./prog bash: ./prog: No such file or directory $ file prog prog: ELF 32-bit LSB executable, Intel 80386, version 1 (SYSV), for GNU/Linux 2.2.5, dynamically linked (uses shared libs), not stripped $ pwd /usr/local/bin $ /usr/local/bin/prog bash: /usr/local/bin/prog: No such file or directory $ less prog | head ELF Header: Magic: 7f 45 4c 46 01 01 01 00 00 00 00 00 00 00 00 00 Class: ELF32 Data: 2's complement, little endian Version: 1 (current) OS/ABI: UNIX - System V ABI Version: 0 Type: EXEC (Executable file) Machine: Intel 80386 Version: 0x1 I have a fancy less, to show that it's an actual executable, here's some more data: $ xxd prog |head 0000000: 7f45 4c46 0101 0100 0000 0000 0000 0000 .ELF............ 0000010: 0200 0300 0100 0000 c092 0408 3400 0000 ............4... 0000020: 0401 0a00 0000 0000 3400 2000 0700 2800 ........4. ...(. 0000030: 2600 2300 0600 0000 3400 0000 3480 0408 &.#.....4...4... 0000040: 3480 0408 e000 0000 e000 0000 0500 0000 4............... 0000050: 0400 0000 0300 0000 1401 0000 1481 0408 ................ 0000060: 1481 0408 1300 0000 1300 0000 0400 0000 ................ 0000070: 0100 0000 0100 0000 0000 0000 0080 0408 ................ 0000080: 0080 0408 21f1 0500 21f1 0500 0500 0000 ....!...!....... 0000090: 0010 0000 0100 0000 40f1 0500 4081 0a08 ........@...@... and $ ls -l prog -rwxrwxr-x 1 1000 devs 725706 Aug 6 2007 prog $ ldd prog not a dynamic executable $ strace ./prog 1249403877.639076 execve("./prog", ["./prog"], [/* 27 vars */]) = -1 ENOENT (No such file or directory) 1249403877.640645 dup(2) = 3 1249403877.640875 fcntl(3, F_GETFL) = 0x8002 (flags O_RDWR|O_LARGEFILE) 1249403877.641143 fstat(3, {st_mode=S_IFCHR|0620, st_rdev=makedev(136, 0), ...}) = 0 1249403877.641484 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2b3b8954a000 1249403877.641747 lseek(3, 0, SEEK_CUR) = -1 ESPIPE (Illegal seek) 1249403877.642045 write(3, "strace: exec: No such file or dir"..., 40strace: exec: No such file or directory ) = 40 1249403877.642324 close(3) = 0 1249403877.642531 munmap(0x2b3b8954a000, 4096) = 0 1249403877.642735 exit_group(1) = ? About the server FTR the server is a xen domU, and the programme is a closed source linux application. This VM is a copy of another VM that has the same root filesystem (including this programme), that works fine. I've tried all the above as root and same problem. Did I mention the root filesystem is mounted over NFS. However it's mounted 'defaults,nosuid', which should include execute. Also I am able to run many other programmes from that mounted drive /proc/cpuinfo: processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Xeon(TM) CPU 3.00GHz stepping : 1 cpu MHz : 2992.692 cache size : 1024 KB fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu tsc msr pae mce cx8 apic mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl cid cx16 xtpr bogmips : 5989.55 clflush size : 64 cache_alignment : 128 address sizes : 36 bits physical, 48 bits virtual power management: Example of a file that I can run I can run other programmes on that mounted filesystem on that server. For example: $ ls -l ls -rwxr-xr-x 1 root root 105576 Jul 25 17:14 ls $ file ls ls: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), for GNU/Linux 2.6.9, dynamically linked (uses shared libs), stripped $ ./ls attr cat cut echo getfacl ln more ... (you get the idea) ... rmdir sort tty $ less ls | head ELF Header: Magic: 7f 45 4c 46 02 01 01 00 00 00 00 00 00 00 00 00 Class: ELF64 Data: 2's complement, little endian Version: 1 (current) OS/ABI: UNIX - System V ABI Version: 0 Type: EXEC (Executable file) Machine: Advanced Micro Devices X86-64 Version: 0x1

  Read the article

• rdiff-backup is taking longer and longer every time it runs

  - by Jakobud

  I've been running rdiff-backup for the past week or so, every night at 4am. It started out not taking that long, but its taking longer and longer and longer every time its runs every night. In some cases there are quite a few new and changed files and in other cases, not so much. It started out taking < 10 minutes, and after a week its taking over 4.5 hrs to run. Take a look at my session stats below: StartTime 1268046002.00 (Mon Mar 8 04:00:02 2010) EndTime 1268046373.50 (Mon Mar 8 04:06:13 2010) ElapsedTime 371.50 (6 minutes 11.50 seconds) SourceFiles 213928 SourceFileSize 277271282225 (258 GB) MirrorFiles 213914 MirrorFileSize 276693097638 (258 GB) NewFiles 16 NewFileSize 578209911 (551 MB) DeletedFiles 2 DeletedFileSize 2598 (2.54 KB) ChangedFiles 27 ChangedSourceSize 5195150 (4.95 MB) ChangedMirrorSize 5217876 (4.98 MB) IncrementFiles 0 IncrementFileSize 0 (0 bytes) TotalDestinationSizeChange 578184587 (551 MB) Errors 0 StartTime 1268132402.00 (Tue Mar 9 04:00:02 2010) EndTime 1268134341.29 (Tue Mar 9 04:32:21 2010) ElapsedTime 1939.29 (32 minutes 19.29 seconds) SourceFiles 213963 SourceFileSize 307959842562 (287 GB) MirrorFiles 213928 MirrorFileSize 277271282225 (258 GB) NewFiles 37 NewFileSize 31265005547 (29.1 GB) DeletedFiles 2 DeletedFileSize 576511960 (550 MB) ChangedFiles 25 ChangedSourceSize 5243761 (5.00 MB) ChangedMirrorSize 5177011 (4.94 MB) IncrementFiles 65 IncrementFileSize 577266412 (551 MB) TotalDestinationSizeChange 31265826749 (29.1 GB) Errors 0 StartTime 1268218802.00 (Wed Mar 10 04:00:02 2010) EndTime 1268225230.15 (Wed Mar 10 05:47:10 2010) ElapsedTime 6428.15 (1 hour 47 minutes 8.15 seconds) SourceFiles 213971 SourceFileSize 307960643843 (287 GB) MirrorFiles 213963 MirrorFileSize 307959842562 (287 GB) NewFiles 9 NewFileSize 694087 (678 KB) DeletedFiles 1 DeletedFileSize 894 (894 bytes) ChangedFiles 38 ChangedSourceSize 30656167797 (28.6 GB) ChangedMirrorSize 30656059709 (28.6 GB) IncrementFiles 48 IncrementFileSize 289278151 (276 MB) TotalDestinationSizeChange 290079432 (277 MB) Errors 0 StartTime 1268305202.00 (Thu Mar 11 04:00:02 2010) EndTime 1268312788.15 (Thu Mar 11 06:06:28 2010) ElapsedTime 7586.15 (2 hours 6 minutes 26.15 seconds) SourceFiles 213971 SourceFileSize 307960643779 (287 GB) MirrorFiles 213971 MirrorFileSize 307960643843 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 15 ChangedSourceSize 30650824127 (28.5 GB) ChangedMirrorSize 30650824191 (28.5 GB) IncrementFiles 16 IncrementFileSize 689437042 (657 MB) TotalDestinationSizeChange 689436978 (657 MB) Errors 0 StartTime 1268391601.00 (Fri Mar 12 04:00:01 2010) EndTime 1268400145.85 (Fri Mar 12 06:22:25 2010) ElapsedTime 8544.85 (2 hours 22 minutes 24.85 seconds) SourceFiles 213974 SourceFileSize 307960784445 (287 GB) MirrorFiles 213971 MirrorFileSize 307960643779 (287 GB) NewFiles 5 NewFileSize 269587 (263 KB) DeletedFiles 2 DeletedFileSize 128921 (126 KB) ChangedFiles 16 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 26 IncrementFileSize 818279963 (780 MB) TotalDestinationSizeChange 818420629 (781 MB) Errors 0 StartTime 1268478002.00 (Sat Mar 13 04:00:02 2010) EndTime 1268488740.33 (Sat Mar 13 06:59:00 2010) ElapsedTime 10738.33 (2 hours 58 minutes 58.33 seconds) SourceFiles 213974 SourceFileSize 307960784238 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784445 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 16 ChangedSourceSize 30650823920 (28.5 GB) ChangedMirrorSize 30650824127 (28.5 GB) IncrementFiles 19 IncrementFileSize 1041846015 (994 MB) TotalDestinationSizeChange 1041845808 (994 MB) Errors 0 StartTime 1268560803.00 (Sun Mar 14 04:00:03 2010) EndTime 1268573194.82 (Sun Mar 14 07:26:34 2010) ElapsedTime 12391.82 (3 hours 26 minutes 31.82 seconds) SourceFiles 213974 SourceFileSize 307960784238 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784238 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 14 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 15 IncrementFileSize 1116911810 (1.04 GB) TotalDestinationSizeChange 1116911810 (1.04 GB) Errors 0 StartTime 1268647203.00 (Mon Mar 15 04:00:03 2010) EndTime 1268662364.88 (Mon Mar 15 08:12:44 2010) ElapsedTime 15161.88 (4 hours 12 minutes 41.88 seconds) SourceFiles 214010 SourceFileSize 307963430178 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784238 (287 GB) NewFiles 37 NewFileSize 2684172 (2.56 MB) DeletedFiles 1 DeletedFileSize 5348 (5.22 KB) ChangedFiles 32 ChangedSourceSize 30656134913 (28.6 GB) ChangedMirrorSize 30656167797 (28.6 GB) IncrementFiles 71 IncrementFileSize 1316460362 (1.23 GB) TotalDestinationSizeChange 1319106302 (1.23 GB) Errors 0 StartTime 1268733603.00 (Tue Mar 16 04:00:03 2010) EndTime 1268750396.76 (Tue Mar 16 08:39:56 2010) ElapsedTime 16793.76 (4 hours 39 minutes 53.76 seconds) SourceFiles 214010 SourceFileSize 307963430156 (287 GB) MirrorFiles 214010 MirrorFileSize 307963430178 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 15 ChangedSourceSize 30650823898 (28.5 GB) ChangedMirrorSize 30650823920 (28.5 GB) IncrementFiles 16 IncrementFileSize 936032413 (893 MB) TotalDestinationSizeChange 936032391 (893 MB) Errors 0 StartTime 1268820002.00 (Wed Mar 17 04:00:02 2010) EndTime 1268834619.90 (Wed Mar 17 08:03:39 2010) ElapsedTime 14617.90 (4 hours 3 minutes 37.90 seconds) SourceFiles 214010 SourceFileSize 307963430156 (287 GB) MirrorFiles 214010 MirrorFileSize 307963430156 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 14 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 15 IncrementFileSize 1289272860 (1.20 GB) TotalDestinationSizeChange 1289272860 (1.20 GB) Errors 0 Is this common behavior? It's only about 300gigs of data total. One important thing to note though, rdiff-backup is backup up stuff over to a USB2 external drive. Maybe thats why its so slow?

  Read the article

• NTFS Permissions - Access Denied even though Explicit Allow and no Deny

  - by chris613

  I'm hoping someone can help me with this NTFS permissions problem. The short version is that I can't write a new file in F:\SomeDir even though I seem to be granted full permissions via both the "Domain Admins" group and a second unprivileged group. The "Effective Permissions" tab in the explorer permissions UI shows that I have full control, and there are no "Deny"s anywhere in the ACL or anything else that looks unusual. I am logged into the machine over RDP and accessing the disk directly, not through a share. F:\SomeDir>set U USERDNSDOMAIN=THEOFFICE.LOCAL USERDOMAIN=THEOFFICE USERNAME=thisisme USERPROFILE=C:\Users\thisisme F:\SomeDir>icacls . . BUILTIN\Administrators:(I)(F) CREATOR OWNER:(I)(OI)(CI)(IO)(F) THEOFFICE\Domain Admins:(I)(OI)(CI)(F) NT AUTHORITY\SYSTEM:(I)(OI)(CI)(F) BUILTIN\Administrators:(I)(OI)(CI)(IO)(F) BUILTIN\Users:(I)(OI)(CI)(RX) Successfully processed 1 files; Failed processing 0 files F:\SomeDir>net group /domain "Domain Admins" The request will be processed at a domain controller for domain THEOFFICE.local. Group name Domain Admins Comment Designated administrators of the domain Members ------------------------------------------------------------------------------- Administrator thatguy thisisme The command completed successfully. F:\SomeDir>echo "whyUNoCreateFile?" > whyUNoCreateFile.txt Access is denied. I searched for answers and came across similar problems that lead to UAC (ex. Why does removing the EVERYONE group prevent domain admins from accessing a drive? ). I can't turn off UAC at the moment, so I try a "regular" group that I'm also part of. This group has no special rights assignments and is not part of any administrative groups. Still no dice: [***** This one command executed in an elevated shell *****] F:\SomeDir>icacls . /grant THEOFFICE\iteveryone:(OI)(CI)F processed file: . Successfully processed 1 files; Failed processing 0 files F:\SomeDir>net group /domain "iteveryone" The request will be processed at a domain controller for domain THEOFFICE.local. Group name ITeveryone Comment Members ------------------------------------------------------------------------------- Administrator thatguy thisisme otherguy someitguy The command completed successfully. F:\ScanningVMsForIBM>echo y > u Access is denied. As you can see, using a "regular" group didn't help. I have logged out and back in to the server to ensure my login token is up to date, and at any rate I belonged to these groups before the server was created. If I grant explicit permission to myself, it does allow me to write files: [***** This one command executed in an elevated shell *****] F:\SomeDir>icacls . /grant THEOFFICE\thisisme:(OI)(CI)F processed file: . Successfully processed 1 files; Failed processing 0 files F:\SomeDir>echo y > u F:\SomeDir>type u y My requirement is for the "Domain Admins" group to have Full Control, or if that's not possible without disabling UAC, then a second group will do, but I can't get either to work. I'm really stumped. Can someone please point out what I could be overlooking?

  Read the article

• Is it possible to repair a Cisco 3500 XL (3548) switch with POST Error messages?

  - by Alex

  I've got an old Cisco 3500 XL, and it seems to have hardware issues. I've loaded the latest IOS and cleared all config. Does anyone have any experience fixing the switch core? I'm a reasonably competent SMD solderer, can I replace/reflow some chips? I've checked the power supply voltages and it's all within tolerance, and no visible signs of any component damage. Some chips are hot to the touch. I understand that these were EOL as of 2007, but should have a lifetime warranty for the electronics. I don't have a Cisco support contract, so I can't file a ticket. What should I do? Console output: switch: dir flash: Directory of flash:/ 2 -rwx 1811584 <date> c3500xl-c3h2s-mz.120-5.WC17.bin 1799680 bytes available (1812992 bytes used) switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC17.bin"...################################################################################################################################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC17.bin" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by cisco Systems, Inc. Compiled Tue 13-Feb-07 15:04 by antonino Image text-base: 0x00003000, data-base: 0x00352924 Initializing C3500XL flash... flashfs[1]: 1 files, 1 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 3612672 flashfs[1]: Bytes used: 1812992 flashfs[1]: Bytes available: 1799680 flashfs[1]: flashfs fsck took 3 seconds. flashfs[1]: Initialization complete. ...done Initializing C3500XL flash. C3500XL POST: System Board Test: Passed C3500XL POST: Daughter Card Test: Passed C3500XL POST: CPU Buffer Test: Passed C3500XL POST: CPU Notify RAM Test: Passed C3500XL POST: CPU Interface Test: Passed C3500XL POST: Testing Switch Core: Passed Error with Switch Core BIST test Phase 0. Returns: Test Complete Low : 0x0FFFFFFF, Test Complete High : 0xFFFFFFFE Test Phase Low : 0x00000040, Test Phase High : 0x00000000 Test Phase Third : 0x00000000, Test Complete Third : 0x000001F8 C3500XL POST FAILURE: Testing Switch Core: Failed C3500XL POST FAILURE: Testing Buffer Table: Failed C3500XL POST FAILURE: Data Buffer Test: Failed C3500XL POST FAILURE: Configuring Switch Parameters: Failed C3500XL POST FAILURE: Switch Core BIST failed. C3500XL POST FAILURE: Cannot test Modules due to failure of Switch Core POST Del Mar Failure (0th Del Mar): req system failed to init C3500XL POST FAILURE: C3500XL POST FAILURE: ATM: required system failed to init C3500XL POST: Ethernet Controller Test: Passed C3500XL POST FAILURE: MII Test: Failed C3500XL POST FAILURE: Error waiting for Ethernet Controller and SW_PARAMS C3500XL POST FAILURE: Initialization/POST failed C3500XL POST FAILURE: AT: Failing because system POST failed Exception (8192)! Debug Exception (Could be NULL pointer dereference) CPU Register Context: Vector = 0x00002000 PC = 0x000F36F4 MSR = 0x00029200 CR = 0x22000024 LR = 0x000F6964 CTR = 0x001DE46C XER = 0x00000000 R0 = 0x00000000 R1 = 0x004E2580 R2 = 0x00000000 R3 = 0x00000000 R4 = 0x00000001 R5 = 0x00000000 R6 = 0x004E2718 R7 = 0x004E2718 R8 = 0x00000008 R9 = 0x00000000 R10 = 0x0000FFFF R11 = 0x00480000 R12 = 0x42000024 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000 R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000 R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x00000000 R24 = 0x00000000 R25 = 0x00000020 R26 = 0x004E2718 R27 = 0x004E2718 R28 = 0x00000020 R29 = 0x00002513 R30 = 0x00000001 R31 = 0x00000000 Stack trace: PC = 0x000F36F4, SP = 0x004E2580 Frame 00: SP = 0x004E25A0 PC = 0x40000016 Frame 01: SP = 0x004E2618 PC = 0x000F6964 Frame 02: SP = 0x004E26A8 PC = 0x000F76DC Frame 03: SP = 0x004E26C8 PC = 0x000E8114 Frame 04: SP = 0x004E26F0 PC = 0x001F5BF8 Frame 05: SP = 0x004E2710 PC = 0x001F5CF4 Frame 06: SP = 0x004E2748 PC = 0x0023F4DC Frame 07: SP = 0x004E2750 PC = 0x0023E650 Frame 08: SP = 0x004E27C8 PC = 0x0023E89C Frame 09: SP = 0x004E27E0 PC = 0x0028AF34 Frame 10: SP = 0x004E27E8 PC = 0x001E38F8 Frame 11: SP = 0x004E2808 PC = 0x001E39A8 Frame 12: SP = 0x004E2820 PC = 0x0014E220 Frame 13: SP = 0x004E28C8 PC = 0x0014E39C Frame 14: SP = 0x00000000 PC = 0x001EB510

  Read the article

• Upgraded Ubuntu, all drives in one zpool marked unavailable

  - by Matt Sieker

  I just upgraded Ubuntu 14.04, and I had two ZFS pools on the server. There was some minor issue with me fighting with the ZFS driver and the kernel version, but that's worked out now. One pool came online, and mounted fine. The other didn't. The main difference between the tool is one was just a pool of disks (video/music storage), and the other was a raidz set (documents, etc) I've already attempted exporting and re-importing the pool, to no avail, attempting to import gets me this: root@kyou:/home/matt# zpool import -fFX -d /dev/disk/by-id/ pool: storage id: 15855792916570596778 state: UNAVAIL status: One or more devices contains corrupted data. action: The pool cannot be imported due to damaged devices or data. see: http://zfsonlinux.org/msg/ZFS-8000-5E config: storage UNAVAIL insufficient replicas raidz1-0 UNAVAIL insufficient replicas ata-SAMSUNG_HD103SJ_S246J90B134910 UNAVAIL ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523 UNAVAIL ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969 UNAVAIL The symlinks for those in /dev/disk/by-id also exist: root@kyou:/home/matt# ls -l /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910* /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51* lrwxrwxrwx 1 root root 9 May 27 19:31 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910 -> ../../sdb lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part9 -> ../../sdb9 lrwxrwxrwx 1 root root 9 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523 -> ../../sdd lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part1 -> ../../sdd1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part9 -> ../../sdd9 lrwxrwxrwx 1 root root 9 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969 -> ../../sde lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part1 -> ../../sde1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part9 -> ../../sde9 Inspecting the various /dev/sd* devices listed, they appear to be the correct ones (The 3 1TB drives that were in a raidz array). I've run zdb -l on each drive, dumping it to a file, and running a diff. The only difference on the 3 are the guid fields (Which I assume is expected). All 3 labels on each one are basically identical, and are as follows: version: 5000 name: 'storage' state: 0 txg: 4 pool_guid: 15855792916570596778 hostname: 'kyou' top_guid: 1683909657511667860 guid: 8815283814047599968 vdev_children: 1 vdev_tree: type: 'raidz' id: 0 guid: 1683909657511667860 nparity: 1 metaslab_array: 33 metaslab_shift: 34 ashift: 9 asize: 3000569954304 is_log: 0 create_txg: 4 children[0]: type: 'disk' id: 0 guid: 8815283814047599968 path: '/dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part1' whole_disk: 1 create_txg: 4 children[1]: type: 'disk' id: 1 guid: 18036424618735999728 path: '/dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part1' whole_disk: 1 create_txg: 4 children[2]: type: 'disk' id: 2 guid: 10307555127976192266 path: '/dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part1' whole_disk: 1 create_txg: 4 features_for_read: Stupidly, I do not have a recent backup of this pool. However, the pool was fine before reboot, and Linux sees the disks fine (I have smartctl running now to double check) So, in summary: I upgraded Ubuntu, and lost access to one of my two zpools. The difference between the pools is the one that came up was JBOD, the other was zraid. All drives in the unmountable zpool are marked UNAVAIL, with no notes for corrupted data The pools were both created with disks referenced from /dev/disk/by-id/. Symlinks from /dev/disk/by-id to the various /dev/sd devices seems to be correct zdb can read the labels from the drives. Pool has already been attempted to be exported/imported, and isn't able to import again. Is there some sort of black magic I can invoke via zpool/zfs to bring these disks back into a reasonable array? Can I run zpool create zraid ... without losing my data? Is my data gone anyhow?

  Read the article

• How to recover data files from xampp-windows to xampp-linux after crash?

  - by David Buehler

  My Windows box died after I developed a database in xampp on it; fortunately I have a backup of the entire F:/TestWeb/Xampp partition. Unfortunately, I did not do an Export (nor dump) of the "Lws2" database before the crash. I have replaced the defunct machine with one running Mint7 (based on Ubuntu 9.04 "Jaunty Jackalope") and installed xampp-linux into the /opt partition, so the new xampp now runs fine in /opt/lampp, and says all the elements are secured by passwords (which I just assigned during this installation.) I assumed that Xamp-Windows installed in November would migrate easily to xampp-linux installed iin February -- a bad assumption. It apparently would have been simple if I had known enough to do an Export or a Dump before the crash, but.... The backup was done to a Network Attached Storage drive, which is formatted as "vfat" so the backup does not carry with it any valid ownership permissions from MySql on NTFS. I now see from my backup that the old data resided in \TestWeb\Xampp\Mysql\Data\Lws2\ and consists of 7 ".frm" files which define my tables. The actual data -- I suppose a ".sql" file or files -- has disappeared, and I am resigning myself to two days of retyping it. But I do not wish to do the table layouts all over again. So I copied Data tree to /opt/lampp/Data -- PhpMyAdmin does not see it. So I copied Lws2 tree to /opt/lampp/Lws2 -- PhpMyAdmin does not see it. So I copied Data tree to /opt/lampp/var/mysql/Data -- PhpMyAdmin does not see it. So I copied Lws2 tree to /opt/lampp/var/mysql/Lws2 -- PhpMyAdmin does not see it. So I adjusted all the permissions to stop saying owner "nobody" to owner "root" and gave full permissions to all groups and to all others, with permissions percolating down, in all 4 trees. You guessed it -- PhpMyAdmin does not see any database named Lws2, only its 4 default ones. I double-checked the permissions and rebooted Linux and repeated the tests. At some point in that process I did see PhpMyAdmin showing "lws2(7)" but when I clicked on it I saw a "no table found" message. I have not been able to recreate that experience. Apparently there are some setup files for MySql and for PhpMyAdmin which need to be set up by running a wizard or two or by editing the files directly. I grepped the TestWeb tree and found an old "ldir = "C:TestWeb\Xampp\MySql\" and a "DataDir = C:TestWeb\Xampp\MySql\" in a .php file and in a .bat file, but I cannot find the corresponding config file names on the /opt partition/ -- so it looks as if these wizards have not been run to create them. What config files files does Linux use to setup MySql config files for PhpMyAdmin? What wizards do I need to run to point the MySql engine and the PhpMyAdmin at the folder /opt/lampp/data/ with its lws2 folder inside it? Or which files do I need to edit, with a sample of what it normally says under Linux? Incidentally, I remember I converted from MyISAM with its .MYD and .MYI files to InnoDB after entering only a small amount of the data -- and I do not know what file types to look for -- perhaps my data is still there but under another guise or in another place? Is it something as simple as linux needing to see "/data/" instead of /Data? I will check that out while waiting for a response. If anyone can point me to documentation that discusses this level of detail -- I will read it avidly! In any case, thanks for any clarification you can give on this thorny problem. wizdum

  Read the article

• How to set up a centralized backup server with lots of offsite workstations, intermittent internet connectivity, and stubborn users?

  - by Zac B

  This might be an impossible question. Context: We have a bunch of computers across around 1000 users. We have a centralized office where 900 of the users work, most of the time. Most of the computers are laptops. They are very frequently coming on and off the network for hours at a time. Users often take their computers home and do lots of work from home. In addition, there are a handful of users who work elsewhere in the country, who are offline (no internet connection whatsoever) for more than half of the time they use their machines. All of the machines are Windows 7/XP. Problem: People are always losing data. One day someone accidentally deletes a bunch of files. The next day someone else installs a bad driver or tries to mess with something in system32 and needs a personal data backup/reinstall of Windows. Because of how many of our business operations are done without an internet connection, and how frequently computers come on- and offline, it's unfeasible to make users use network storage for all of their data. We tried giving them Dropboxes, and they stored their files elsewhere. We bought and deployed Altiris, and they uninstalled it and blamed us when they couldn't get files back that they accidentally deleted while they were offline and hadn't taken a backup in months. We tried teaching them backup best-practices, and using scheduled sync tools to upload things to the network drives, and they turned them off because they "looked like viruses". It doesn't help that many of these users are pretty high up in the business and are not amicable to any sort of "you need to do something regularly because we say so" solution. Question: Other than finding another job where IT is treated differently and users are willing to follow best practices, how would people recommend I implement a file backup solution that supports the following: Backs up to a centralized server over LAN or WAN whenever a network link becomes available, or on a schedule. Supports interrupted/resumed backups (and hopefully file-delta only backups), since connections to the network (WAN or LAN) are often slow and only open for half an hour or so. Supports relatively rapid, "I accidentally deleted the TPS reports! Oh no!" single-file recovery, ideally administered from the central backup server rather than the client PC. Supports local-to-local file delta backup on a schedule, so that users without a network connection for a few days can still retrieve accidental deletions or whatnot. Ideally, the local stored backups would be pushed up to the server whenever network link is available. Isn't configurable on the clients without certain credentials. Because the CFOs (who won't give up their admin rights on the domain) will disable it if they can. Backs up the entire hard drive. There are people who are self-righteous about storing things in C:\, or in the recycle bin, or in the C:\Windows dir (yes, I know). I'm fine integrating multiple products/solutions, or scripting different programs together myself (I'm a somewhat competent programmer), but I've been drawing a blank on where to start. Dropbox is folder-specific, Altiris doesn't cope with LAN outages or interrupted/resumed backups, Volume Shadow Copy is awesome for a local-to-local solution, but I don't know how to push days of stored shadow copies up to a server in a 2 hour window of network access. The company is fine with spending decent money on this, thousands (USD) on a server, and hundreds on clients, if necessary. I want to emphasize that this isn't a shopping list request. While I wish there was a program out there that did what I want, I've looked pretty hard, and not found anything that fits the bill. Instead, I'm hoping for ideas on where to start hacking things together from scratch/from different technologies to make something stable that works. Cheers!

  Read the article

• Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

  - by Joe Hopfgartner

  I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

  Read the article

• what is the best mid/high-end class audio/music creation audio sound card?

  - by Chris

  Hello, I have a computershop myself, and I repair computers. But one of the things I really don't know (yet) is the performace od audio cards for music creation with midi. I have searched and searched and came up with some good reviews, but after browsing for a couple of hours I could't see the trees trough the forrest :-D (it's a dutch expression) At one moment I thought the M-Audio - Delta 1010LT would be a good PCIe card, later on I read that this card was released years ago. (but that could be false information) Also any personal expierence would be great, but not necessairy. I have searched a few cards, and I hope someone can help me make a choice for a friend of mine. He's buget is between $100 and $350 I know there are audio cards from $ 500 - $1850,- this is just too expensive. The following specs are crucial: ASIO Midi Mic in minimal 5.1, 7.1 recommended it's not for airplay, but just to compose music at home. using Ableton and midi keyboard. 1. M-Audio - Delta 1010LT: 8 x 8 analog I/O 2 mic preamps or line inputs S/PDIF digital I/O (coaxial) with 2-channel PCM SCMS copy protection control digital I/O supports surround-encoded AC-3 and DTS pass-through 1 x 1 MIDI I/O directly drive up to 7.1 surround (bass management software included) software controlled 36-bit internal DSP digital mixing/routing +4dbu/-10dBV operation individually switched in software word clock I/O for sample accurate device synchronization 2. RME HDSP 9632: * Stereo Analog Ein- und Ausgang, symmetrisch*, 24-Bit/192kHz, > 110 dB SNR * Optionale Erweiterungsboards mit je 4 symmetrischen Ein- und Ausgängen * Alle analogen I/Os voll 192 kHz-fähig, also keine Reduzierung der Kanalzahl * 1 x ADAT Digital In/Out, 96 kHz-fähig (S/MUX) * 1 x SPDIF Digital In/Out, 192 kHz-fähig * 1 x Breakout Kabel für koaxialen SPDIF-Betrieb* * Also bis zu 16 Ein-und Ausgänge gleichzeitig nutzbar! * 1 x Stereo Kopfhörerausgang, parallel zum analogen Ausgang, aber eigene Pegelanpassung * 1 x MIDI I/O für 16 Kanäle Hi-Speed MIDI über Breakout Kabel * DIGICheck, RMEs einzigartiges Meter- und Analysetool mit Spectral Analyser, Professionelle Level Meter 2/8/16-Kanalig, Vector Audio Scope und diversen weiteren Analysefunktionen * HDSP Meter Bridge: Frei skalierbare Levelmeter mit Peak- und RMS Berechnung in Hardware * TotalMix: 512-Kanal Mischer mit 40 Bit interner Auflösung 3. EMU 1212M (1212 M) PCIe: * Top kwaliteit convertors 24-bit/192kHz convertors. * Hardware gestuurde effecten. * DSP zero-latency hardware mixen en monitoring. * Analoge en digitale I/O plus MIDI. * EMU Production Tools Software Bundle - Cakewalk SONAR , Steinberg Cubase LE, Ableton Live E-MU Edition **EMU 1212M PCI-e inputs/outputs:** * 2 balanced jack inputs. * 2 balanced jack outputs. * 24-bit/192kHz ADAT I/O. * 24-bit/192kHz Coaxiale S/PDif I/O switchable to AES/EBU. * MIDI I/O. 4. M-Audio Audiophile 192: - Up to 24-bit/192kHz audio - 2 balanced analog inputs (1/4” TRS) - 2 balanced analog outputs (1/4” TRS) - S/PDIF digital I/O (coaxial RCA connectors) with 2-channel PCM - SCMS copy protection control - Digital I/O supports surround-encoded AC-3 and DTS pass-through - Direct hardware input monitoring via separate balanced 1/4” TRS monitor outputs - Software routing of inputs and outputs - Digital I/O can be routed to/from external effects - 16-channel MIDI I/O - ASIO, WDM, GSIF 2 and Core Audio driver support for compatibility with most applications - 64-bit driver support for Windows - PCI 2.2 compatibility - Apple G5 compatible - Incompatible exceptions - Includes Ableton Live Lite music production software, so you can make music right away - Works with other Delta cards Technical Specifcations: - Compatibility - ASIO - WDM - GSIF 2 - Core Audio

  Read the article

• Intermittent lockups, unable to diagnose in over a year

  - by Magsol

  Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

  Read the article

• XenServer Converting HVM to Paravirtualised

  - by Karl Kloppenborg

  Recently I have been tasked with the daunting process of converting a setup of HVM enabled VMs (running on Citrix XenServer 5.6.0) into PV (paravirtualised) containers. The constraints of the project was that: The operating system must be functionally identical after the migration. minimal modification to the operating system (with exception of kernel / drive mapping) I also was allowed to change the bootloader(ie, grub) in what ever way I see fit. However, I have attempted this, I will firstly like to show you my steps I took. This at the moment is CentOS5.5 specific: Steps: yum install kernel-xen This installed: 2.6.18-194.32.1.el5xen edited: /boot/grub/menu.lst changed my specs to match: title CentOS (2.6.18-194.32.1.el5xen) root (hd0,0) kernel /vmlinuz-2.6.18-194.32.1.el5xen ro root=/dev/VolGroup00/LogVol00 console=xvc0 initrd /initrd-2.6.18-194.32.1.el5xen.img Then I changed my xenserver parameters to match: xe vm-param-set uuid=[vm uuid] PV-bootloader-args="--kernel /vmlinuz-2.6.18-194.32.1.el5xen --ramdisk /initrd-2.6.18-194.32.1.el5xen.img" xe vm-param-set uuid=[vm uuid] HVM-boot-policy="" xe vm-param-set uuid=[vm uuid] PV-bootloader=pygrub xe vbd-param-set uuid==[Virtual Block Device/VBD uuid] bootable=true Some things to note, I am running a VolGroup LVM ;) Anyways, after all these steps (which aren't much!) I boot the VM and it boots initial kernel just fine, however I am presented with this error: Boot Screen: device-mapper: dm-raid45: initialized v0.2594l Waiting for driver initialization. Scanning and configuring dmraid supported devices Scanning logical volumes Reading all physical volumes. This may take a while... Activating logical volumes Volume group "VolGroup00" not found Creating root device. Mounting root filesystem. mount: could not find filesystem '/dev/root' Setting up other filesystems. Setting up new root fs setuproot: moving /dev failed: No such file or directory no fstab.sys, mounting internal defaults setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys switchroot: mount failed: No such file or directory Now my hints are that it cannot detect / because of the fact that when you change from HVM mode to PV it does something (not that obvious) When you make a SR (storage) on a HVM, you get it mounted to the guest os as /dev/hda. However in PV mode, this presents itself as /dev/xvda... Could this be the answer? and if so, how the heck to I implement it?? Update: So I have gotten a bit further in my quest, as it now detects the LVM's... To do this, I required to recompile the xen-kernel initrd image. Command: mkinitrd -v --builtin=xen_vbd --preload=xenblk initrd-2.6.18-194.32.1.el5xen.img 2.6.18-194.32.1.el5xen Now when I boot I get this: Boot Screen: Loading dm-raid45.ko module device-mapper: dm-raid45: initialized v0.2594l Scanning and configuring dmraid supported devices Scanning logical volumes Reading all physical volumes. This may take a while... Found volume group "VolGroup00" using metadata type lvm2 Activating logical volumes 3 logical volume(s) in volume group "VolGroup00" now active Creating root device. Mounting root filesystem. mount: error mounting /dev/root on /sysroot as ext3: Device or resource busy Setting up other filesystems. Setting up new root fs setuproot: moving /dev failed: No such file or directory no fstab.sys, mounting internal defaults setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys switchroot: mount failed: No such file or directory Kernel panic - not syncing: Attempted to kill init!

  Read the article

• Amazon EC2 Instance - m1.medium Ubuntu 12.04 - Started to crash three days ago

  - by Joy

  The environment: Amazon EC2 Instance - m1.medium Ubuntu 12.04 Apache 2.2.22 - Running a Drupal Site Using MySQL DB Server RAM info: ~$ free -gt total used free shared buffers cached Mem: 3 1 2 0 0 0 -/+ buffers/cache: 0 2 Swap: 0 0 0 Total: 3 1 2 Hard drive info: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 4.7G 2.9G 62% / udev 1.9G 8.0K 1.9G 1% /dev tmpfs 751M 180K 750M 1% /run none 5.0M 0 5.0M 0% /run/lock none 1.9G 0 1.9G 0% /run/shm /dev/xvdb 394G 199M 374G 1% /mnt The problem About two days ago the site started failing becaue the MySQL server was shut down by Apache with the following message: kernel: [2963685.664359] [31716] 106 31716 226946 22748 0 0 0 mysqld kernel: [2963685.664730] Out of memory: Kill process 31716 (mysqld) score 23 or sacrifice child kernel: [2963685.664764] Killed process 31716 (mysqld) total-vm:907784kB, anon-rss:90992kB, file-rss:0kB kernel: [2963686.153608] init: mysql main process (31716) killed by KILL signal kernel: [2963686.169294] init: mysql main process ended, respawning That states that the VM was occupying 0.9GB, but my Ram has 2GB free, so 1GB was still left free. I understand that in Linux applications can allocate more memory than physically available. I don't know if this is the problme, it's the first time that it has started to happen. Obviously, the MySQL server tries to restart, but there's no memory for it apparently and it won't restart. Here is its error log: Plugin 'FEDERATED' is disabled. The InnoDB memory heap is disabled Mutexes and rw_locks use GCC atomic builtins Compressed tables use zlib 1.2.3.4 Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 Completed initialization of buffer pool Fatal error: cannot allocate memory for the buffer pool Plugin 'InnoDB' init function returned error. Plugin 'InnoDB' registration as a STORAGE ENGINE failed. Unknown/unsupported storage engine: InnoDB [ERROR] Aborting [Note] /usr/sbin/mysqld: Shutdown complete I simply restarted the Mysql service. About two hours later it happened again. I restarted it. Then it happened again 9 hours later. So then I thought of the MaxClients parameter of apache.conf, so I went to check it out. It was set at 150. I decided to drop it down to 60. As so: <IfModule mpm_prefork_module> ... MaxClients 60 </IfModule> <IfModule mpm_worker_module> ... MaxClients 60 </IfModule> <IfModule mpm_event_module> ... MaxClients 60 </IfModule> Once I did that, I had the apache2 service restart and it all went smoothly for 3/4 of a day. Since at night the MySQL service shut down once again, but this time it wasn't killed by the Apache2 service. Instead it called the OOM-Killer with the following message: kernel: [3104680.005312] mysqld invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0, oom_score_adj=0 kernel: [3104680.005351] [<ffffffff81119795>] oom_kill_process+0x85/0xb0 kernel: [3104680.548860] init: mysql main process (30821) killed by KILL signal Now I'm out of ideas. Some articles state that the ideal thing to do is change the kernel behaviour with the following (include it to the file /etc/sysctl.conf ) vm.overcommit_memory = 2 vm.overcommit_ratio = 80 So no overcommits will take place. I'm wondering if this is the way to go? Keep in mind I'm no server administrator, I have basic knowldege. Thanks a bunch in advance.

  Read the article

• Symantec Protection Suite and System Recovery 2011 Desktop Edition

  - by rihatum

  I am re-posting this as my previous question was being treated as if I am "Shopping or seeking Product Recommendations" even though I was NOT - BTW they have deleted my comments too which were not offensive in nature. anyway - I have re-phrased some parts of my question and I hope SF Admins "Do Not Modify / Edit" this one - will be most grateful for that. I have a lot of respect for the People who visit this SITE and help others ! Just To clarify : Just to go by SF rules - I am not seeking someone to Design this solution, I am simply seeking real world examples, experiences, technical expert opinions / suggestions, any tips or tricks they may have or any problems they may have faced while doing something similar above with these products. I am also not asking for Capacity Planning for Storage, We have done some research and I am seeking Expert Assurance / Suggestions. We (our company) are planning to deploy Symantec Endpoint Protection and Symantec Desktop Recovery 2011 Desktop Edition to our 3000 - 4000 workstations (Windows7 32 and 64) with a few 100s with Windows XP 32/64 Bit. I have read the implementation guide for SEP and have read tech-notes for Desktop Recovery 2011. Our team have planned to deploy this as follows : 1 x dedicated SQL 2008R2 for Symantec Endpoint Protection (Instead of using the Embedded Database) 1 x Dedicated SQL 2008R2 for Symantec Desktop Recovery 2011 (Instead of using the Embedded Database) 1 x Dedicated W2K8 R2 Box for the SEPM (Symantec Endpoint Protection Manager - Mgmt. APP) 1 x Dedicated W2K8 R2 Box for the Symantec Desktop Recovery 2011 Management Application Agent Deployment : As per Symantec Documentation for both of the above, an agent can be pushed via the Mgmt. Application (provided no firewalls are blocking ports required etc. - we have Windows firewall disabled already). Server Hardware : Per SQL Server : 16GB RAM + SAS DISKS + Dual XEON, RAID-10 for the SQL DB or I can always mount a LUN from our existing Hitachi or EMC SAN. SEPM Server : 16GB RAM + SAS DISKS + DUAL XEON System Recovery MGMT SERVER : 16GB RAM + SAS DISKS + DUAL XEON Above is the initial plan we have for 3000 - 4000 client workstation (Windows) Now my Questions :-) a) If we had these users distributed amongst two sites with AD DC / GC in each site, How would I restrict SEPM and Desktop Mgmt. solution to only check for users in their respective site ? b) At present all users are under one building but we are going to move some dept. to a new location (with dedicated connectivity), How would we control which SEPM / MGMT Server is responsible for which site ? c) We have netbackup in our environment backing up other servers, I am planning to protect these 4 (2 x SQL, 1 x SEPM, 1 x System Recovery Mgmt. Server) via netbackup or I can use System recovery 2011 server edition on all 4 of these boxes as well. (License is not an issue as we have the complete symantec portfolio included in our license). d) Now - Saving Desktop backups - What strategies have you implemented ? Any best practice recommendation for a large user base ? I was thinking to either mount a LUN from our Hitachi SAN on the Symantec Recovery Server itself or backup to the users hard drive locally and then copy it over to a network location ? Suggestions welcome :-) If you have anything to add / correct - that will be really helpful before diving into the actual implementation phase. Will be most grateful with your suggestions, recommendations and corrections with above - Many Thanks !

  Read the article

• How to diagnose and solve an erratic "HDCP Support Required"?

  - by Jom Orgstrom

  I am playing a digital tv broadcast on Windows Media Center for Windows 7. I built this system so it works with HDCP, and in fact I have been able to watch tv and bluray before with this same computer. However, I suddenly started getting an "HDCP Support Required" error from WMC. The entire message is as follows: HDCP Support Required High-bandwidth Digital Content Protection (HDCP) may not be supported by the current video card. Use an HDCP-compliant display, video card, and video driver. Or, connect using an analog connection such as component or VGA. Relevant specs are: CPU: Ivy Bridge Core i7-3770 Motherboard: Asus P8H77-I Memory: 16GB DDR3-1600 Graphics: Radeon HD 7850 (Driver by AMD, version 8.982.0.0 built on 2012/07/27) Display: Acer P243w connected by HDMI Sound: Roland Quad-Capture (It complains even when I use the bundled VIA HD Audio) TV Tuner: I-O Data GV-MC7/HZ3 OS: Windows 7 Professional SP1, Windows Update enabled. All patched and up to date. As you can see, there is nothing weird or old about my setup. I am also not doing anything strange, not doing any overclocking, weird system changes and so on. One thing that does happen from time to time, is that the display goes black for a few seconds (sometimes when watching media contents, sometimes when just using photoshop or Visual Studio). This happened with my previous setup as well, so I'd be inclined to think it is a display or cable issue (apart from the BD drive, these are the only things I kept from my previous setup to this one). But being a digital transfer, as far as I know, these things either work or not. Never erratically or with decreased quality. The thing is that sometimes I can watch the TV, sometimes not. This happens with recorded programs as well, so it's not a per-program thing. Sometimes rebooting helps, sometimes it doesn't. Sometimes unplugging and plugging back the HDMI connector helps, sometimes it doesn't. Sometimes doing so doesn't even turn the screen back on, so I have to reboot. Unfortunately, WMC's error message is quite unhelpful. I'd like to know exactly where the problem is, so I can solve it. I don't want to buy a brand new display just to then find out it was a registry setting that was misconfigured. I've tried looking at the system event viewer, but these errors don't show up at all in there. Other people who have this problem seem to have a setup that is not HDCP compliant, so I turn to you guys here. Anybody knows how to diagnose this problem? Edit: So I got the Cyberlink Blu-ray disc advisor. I ran it and told me everything was okay, except for the Video Connection Type, which showed as "Digital (without HDCP)". I then proceeded to unplug the power cable from the monitor, plugged it in again, ran the tool again, and now it's "Digital (with HDCP)". Needless to say, I can watch my TV and recorded programs on WMP again. I'm guessing that at some point, something may be slightly wrong with the HDCP setup, and Windows decides to reset the entire content protection path (which leads to the screen blanking out). Usually the reset succeeds, but sometimes it doesn't, so Windows defaults to turning HDCP off. There's no way to turn it back on, except by doing a hard reset of the display. I really want to know what the exact error was, so I can fix it. Is it the cable? is it the display? is it the video card? the driver? Also, is there any other way to try and turn HDCP on again without having to hard reset the display? Oh, questions, questions...

  Read the article

• Can I make my drives visible and change their partition type without losing my data?

  - by user165408

  I have made a lot of mistakes and now I cannot see my hard disk nor I can start my operating system on my laptop. All my passwords and important files on my hdd without any backup. I followed this course of action Changed my hard disk partitions to dynamic just for getting 5th partition. (1st mistake) Decreased partitions to 4 again. Backed up operating system from 4th to 3rd partition with Norton Ghost. Booted from a live CD for Windows XP. Formatted 4th partition and moved my all important data from 1st and 2nd partitions to the 4th partition. Deleted 1st and 2nd partitions and got 1 partition from half of empty space. So I have just 3 partitions and empty space between 1st and 2nd partitions. Tried to install Windows 8 to the first partition but it did not allow because it is dynamic. Also it did not allow to install to other partitions. Tried to install Windows XP to the 1st partition but it said if I continue I cannot use other drivers. Therefore I escaped from installing it. Booted from the Windows XP live CD then increased 1st partiton to less than 400mb of empty space. Therefore I thought it will be adjacent but it was shown as 2 partitions. In my computer I see just 3 drivers. Using Norton Ghost I recovered my OS to the 1st partition. (2nd mistake it was on 4th partition originally) Booted from a Windows XP live CD I tried to install bcdedit to the Windows XP live CD but it did not work. Then I tried to install EaseUS Partition Master Home Edition. It was installed with errors then I start it and it showed me an error like there is no hard disk. I looked to my PC and my drivers were not there. Booted from the Norton Ghost CD and it did not show me my drivers either, but before I was able to see them. I checked numbers of partition shown by the Norton Ghost utility and they are still have same numbers so I have to see my drivers but I cannot see them now. My hard disk is shown as extarnal dynamic now so I cannot see any drive in my PC in the live Windows XP. There are two options; first one is import extarnal disk and second one is convert disk to basic. Will they delete my data? I fear booting from CDs like Windows XP live CD, Norton Ghost CD, and the operating system CD/DVD, because they may overwrite a few MB their data to my data. These recover tools are already exist in Windows XP live CD by The Ultimate Boot CD for Windows. Can any of them help me? CompuAppa SwissKnife V3 DBXtract Disk Investigator Fab's AutoBackup 2.0 FileRecovery Floppy Repair Free Undelete Handy Recovery Recovery Manager Restorastion Restorastion Help File by UBCD4Win UnChk Unstoppable Copier Finally How can I make it so that my drives are visible again without losing my data? How can I convert my dynamic partitions to basic without losing my data?

  Read the article

• Where to download replacement "Explorerframe.DLL" Files for x64 Windows 7 Pro?

  - by Ben Franchuk

  After posting this question, I did some research to reveal what the problem likely was, and found what I need to fix. Following this is the original post, then my updated question. A few months ago I ended up requiring to change my computer's SID to fix a problem it had been having- Instead of fixing the problem, though, it screwed up my at-the-time current install of windows, to the point of me needing to do a fresh install. As I am in possession of an OEM copy of Windows 7 Pro 64 Bit, I successfully reinstalled over the dead copy with that (all the files that were on the computer previous to this windows install were put in a Windows.old folder). Everything installed and worked absolutely fine, except for one thing. The problem I am experiencing is that, in some Windows Explorer windows, the explorer pane doesn't show. Instead, it simply shows a white area where the pane would show. This makes some software not usable, I recently realized; Software such as Cubase, which use just the explorer pane to select file save locations, cannot save at all as the pane itself is... not operational. Below is a screenshot of this problem as it occurs in cubase; ...and again as it shows in UTorrent in the save location selector window. The highlighted area is where the sidebar would NORMALLY be. Pardon my scribbling over some of the things in the window- I would personally rather the internet did not get a glimpse of my files. I have yet to find a common reason why the pane works in some applications when they pull explorer, and others not. I have yet to see it go away, and the software affected by it has been affected since I reinstalled my copy of windows. Initially, I was able to live with it as I can type out save locations in the file name bar to navigate, but with software like Cubase, I do not have this option. Reinstalling windows again is NOT an option. Here's the updated question. After posting this question originally, I did some research on the problem in question, and it turns out that this is extremely easily fixable via replacing the file "ExplorerFrame.DLL" which is located in the System32 and SystemWOW64 Folders, in the windows folder, on the C:\ drive. As I quite frequently customize my computer, this is a normal thing for me to do and I know exactly how to safely and properly replace this file. The only problem is that I cannot for the life of me find a download of this file that actually works with my computer. I tried a couple from some different sites but they all caused explorer to not restart (I was given an error when starting the application from Task Manager) and was forced to revert to the broken .DLL files. Since there are 2 separate "ExplorerFrame.DLL" files; one for 64 bit and the other for 32 bit, I am assuming that I will need to download 2 separate versions to replace the corrupted ones. Where can I acquire these files? I am currently running Windows 7 Professional x64 Bit.

  Read the article

< Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >