Search Results

Search found 14772 results on 591 pages for 'full trust'.

Page 437/591 | < Previous Page | 433 434 435 436 437 438 439 440 441 442 443 444  | Next Page >

• Windows 7 UAC (user access control) is being disabled on every reboot

  - by Christian Thamer

  To put it simply, I noticed UAC was disabled so I enabled it. I was prompted to reboot the computer for the changes to take effect. Upon my reboot I checked the settings again as I hadn't disabled UAC in the first place. It was again set to off (never notify). For the heck of it I repeated the process a couple of more times. Same result each time. I have Microsoft Security Essentials running a full scan nightly so I should be protected from viruses. I also did an on demand scan with the online tool at www.antivirus.com. Nothing was found. Other than the fact that UAC is being disabled on each reboot I have no other reason to suspect a virus. So my question is does anyone have insight into if this is a possible problem with a virus or other malware changing my UAC settings on each boot or is it possibly a problem with Windows and UAC itself? If it is malware are there suggestions for other products outside of the ones I have used to detect and remove it.

  Read the article

• Advance DNS - Redirecting Emails to new webhost

  - by Martin

  I am not to sure if this question belongs here but I will surely find out soon enough. I have two web hosts (Not sure why it has been setup this way but it has). I do not want to use the original web host to handle the emails as the Data that we get from them is 500 mb which is already full with hosting the website. The second web host has an unlimited data plan and was created so we could use this host for the email accounts. Now the problem is I have reset the Advance DNS Zone records on both accounts and I am not sure what they were before. (Silly me should have taken a backup of how it was setup before hand I know) Emails were working before and going to the second hosts server now they are going to the first host but it has no email addresses setup for use so all emails are bouncing saying that the address does not exist. Host 1 IP: 192.185.96.110 Host 2 IP: 27.54.88.66 So far I have changed the Advanced DNS Zone record on Host 1 with the following: A Record: mail.australisinstitute.qld.edu.au - 27.54.88.66 I have not made any changes on Host 2 and both hosts have the default MX Records. If I need to provide any more information I can but I just hope someone can decipher what I have said haha. Cheers in advance!

  Read the article

• File download speed issue over a dedicated fibre link

  - by nixnotwin

  My ISP has installed a fibre based dedicated internet connection at the place where I work. In the beginning the connection terminated at one of the ISP's core routers. It resulted in a strange issue. Eventhough the assigned speed was 5mbps, when tests were done by downloading large files over http and ftp from multiple locations, the speed never went above 2mbps. But bittorrent downloads reached 5mbps. Even file download from the ISP servers were fine. So, at the ISP our link was attached directly to their edge router. After this file downloads from high bandwidth servers, like Google and MS, reached the 5 mbps limit. Sometimes the speed would fall down below 2 mbps and suddenly it will go up to the 5 mbps limit ( it keeps on happening during any single file download). But other downloads like ubuntu apt repositories still struggle to go above 2 mbps. The engineers at the ISP have not been able to sort out the issue. After they moved us to their edge router instead of giving us 8 public ip's, they just gave 4 ip's. When we enquired about it, they told us that giving more ip's would result in arp overload at their edge router. But somehow I was able to convince them to give us the 8 ip's which we wanted. But the file download issue has remained. What might be the reason for files from different location getting downloaded with different speeds, that too with heavy fluctuation in speeds? I have downloaded files from same url's from a connection belonging to another smaller ISP, and the speeds were fine and reached full 5 mbps limit.

  Read the article

• Symantec Endpoint Protection Virus Definitions

  - by Gus Denton

  I have done some Googling but I cannot get a definitive answer certainly not from the Symantec KB. I have a Virtualised Win 2003R2 server 32bit. It has been provisioned to me with Symantec Endpoint Protection 11.0.62xxx CLIENT (not a definitions server) the directory C:\Program Files\Common Files\Symantec Shared\VirusDefs is 750MB IT doesn't contain .tmp directories so it is NOT a corrupt definitions server. IT does contain directories named with a date pattern YYYYMMDD.xxx Some of these folders are 12 months old and I would like to recover the space. The sysmantect forums are full of this stuff but a lot of the postings contain links back to documents that are not specific to End Point Protection Client. It appears that I should be able to delete the older folders and all will be OK. with a service restart however there is a warning about having Live Update Administrator Installed Firstly I have no idea if I have this installed how to I check and secondly can I just ditch these old files and restart ? Regards Gus Denton Learning and Teaching Uni of New South Wales Sydney Australia For those trying to assist me I thankyou. I have followed some instructions found on the Symantec site and assumed that the response from Nixphoe would resolve my issue. It appears that as I am on a provisioned VM from a central IT unit I cannot run the Symantec commands from the Run prompt as my admin creds to get me in. (smc -stop) Basically I need to claw back some Diskspace from the c: drive which is being filed up with WSUS patches and Symantec files. I have managed to delete one symantec cache through the live update control panel and recovered 470Mb I suppose my last question for those more experienced than myself is, can I simply remove say the two oldest virus definition folders without completely foobaring the End Point protection and the server ? Regards Gus

  Read the article

• Tell Tomcat to drop requests instead of dying "All threads (150) are currently busy"

  - by Nicolas Raoul

  My Tomcat 6.0.26 sometimes dies saying: SEVERE: All threads (150) are currently busy, waiting. Increase maxThreads (150) or check the servlet status ... then Tomcat shuts down, and users can't access the webapp until I restart Tomcat manually. Some of the threads indeed take a long time to execute, it is by-design, not a thread-gone-wild problem. I know I could increase maxThreads, but that is not a viable solution, because the server might receive requests even more requests. QUESTION: Instead of dying, can I tell Tomcat to just drop requests when maxThreads is reached and the AJP/1.3 backlog is full? Below is my server.xml in any case: <?xml version='1.0' encoding='utf-8'?> <Server port="8005" shutdown="SHUTDOWN"> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <Listener className="org.apache.catalina.core.JasperListener" /> <Listener className="org.apache.catalina.mbeans.ServerLifecycleListener" /> <Listener className="org.apache.catalina.mbeans.GlobalResourcesLifecycleListener" /> <GlobalNamingResources> <Resource name="UserDatabase" auth="Container" type="org.apache.catalina.UserDatabase" description="User database that can be updated and saved" factory="org.apache.catalina.users.MemoryUserDatabaseFactory" pathname="conf/tomcat-users.xml" /> </GlobalNamingResources> <Service name="Catalina"> <Executor name="tomcatThreadPool" namePrefix="catalina-exec-" minSpareThreads="100"/> <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" enableLookups="false" useBodyEncodingForURI="true" backlog="150" maxThreads="150" executor="tomcatThreadPool" keepAliveTimeout="5000" connectionTimeout="300000" /> <Engine name="Catalina" defaultHost="localhost" jvmRoute="ecm1"> <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/> <Host name="localhost" appBase="webapps" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false"> </Host> </Engine> </Service> </Server>

  Read the article

• Exchange Server 2010: move mailboxes from recoveded and mounted edb to user's mailbox

  - by user36090

  One of our exchange servers crashed, and I am trying to recover the mailboxes. We had 1 exchange 2003 server named "apex" and 1 exchange 2010 server named "2008Enterprise. the exchange 2010 server named "2008Enterprise" crashed. I created a new exchange 2010 server named "Providence". I ran the command on Providence: New-MailboxDatabase -Recovery -Name JBCMail -Server Providence -EdbFilePath "c:\data\Exchange\Mailbox\Mailbox Database 0579285147\Mailbox Database 0579285147.edb" -LogFolderPath "c:\data\Exchange\Mailbox\Mailbox Database 0579285147" this command executed and finished without error I then ran the command: eseutil /p E00 this command was executed from the below directory: c:\data\Exchange\Mailbox\Mailbox Database 0579285147 I then mounted the JBCMail with the mount command note: I do not have my full typed command. Inside my Exchange Management Console (EMC) I can view the new mailbox database named JBCMail. The JBCMail database is show as mounted on the exchange server named Providence. I can see the crashed Exchange server named 2008Exchange. In the EMC the crashed exchange server states the Copy Status under ServerConfiguration-Mailbox is ServiceDown. From here I need to recover three mailboxes The mail boxes are on the apex server. How do I move the mailboxs from apex to Providence? How do I restore the mailboxes from JBCmail mounted database to the user's mailbox? I do not fully understand how to use the Restore-Mailbox command because when I use this command it tries to restore the mailbox to the dead apex server. Restore-Mailbox -ID 'Jason Young' -RecoveryDatabase JBCMail

  Read the article

• Windows product key is valid but wont activate

  - by pnongrata

  Last month, I needed to install Windows XP (Pro Version 2002 SP3) from a Reinstallation CD a co-worker gave me, and with a product key the IT team told me to use. Everything installed successfully and I have been using the XP machine for the last 30 days without any problems; however it kept reminding me to activate Windows, and of course, I never did (laziness). It now has me locked out of my machine and won't let me log in until I activate it. So I proceed to the Activation Screen which asks me: Do you want to activate Windows now? I choose "Yes, let's activate Windows over the Internet now.", and click the Next button. It now asks me: Do you want to register while you are activating Windows? I choose "No, I don't want to register now; let's just activate Windows.", and click the Next button. I now see the following screen: Notice how the title reads "Unauthorized product key", and how there are only 3 buttons: Telephone Remind me later Retry Please note that the Retry button is disabled until I enter the full product key that IT gave me, then it enables. However, at no point in time do I see a Next button, indicating that the product key was valid/successful. So instead, I just click the Retry button, and the screen refreshes, this time with a different title Incorrect product key Could something be wrong with the Windows XP reinstallation CD (do they "expire" after a certain amount of time, etc.)? Or is this the normal/typical workflow for what happens when you just have a bad product key? I ask because, after this happened I emailed IT and they supplied me whether several other product keys to try. But every time its the same result, same thing happening over again and again. So I guess it's possible that IT has given me several bad keys, but it's more likely something else is going on here. Any thoughts or ways to troubleshoot? Thanks in advance!

  Read the article

• Font for Wine that supports the entire character set of the Win32 Console?

  - by Brian Campbell

  I would like to be able to display in the Wine console all characters that the Win32 console can display. I've written a small test program to print out all 8-bit characters: #include <stdio.h> int main(int argc, char *argv[]) { int i, j; for (i = 0; i <= 0xF0; i+=0x10) { for (j = i; j <= i + 0x0F; ++j) printf("%2x:%c", j, (char)j); printf("\n"); } getchar(); return 0; } Under Wine, the best I can do so far is using Andale Mono: While this is what I see on Windows Server 2008: Is there anywhere I can legally download a font that will allow me to view all of those characters under Wine? edit I've found a set of DOS fonts that includes a CP437 font, which should cover the character set I'm interested in. However, even if I install this font, wineconsole doesn't seem to recognize it. Is there any way I can get wineconsole to use this font, or convert this font to a format that wineconsole can use? Or is there any way I can extract fonts from DOSEMU for use in Wine? Oh, and I should probably mention that I'm on Mac OS X 10.6.2, installing Wine via MacPorts, using the wine-devel package. more information I have tried installing some console fonts that should cover the full character set as Mac OS X fonts (such as the NewDOS font listed above, and a font I tried converting from the fonts supplied by DOSEMU). Wine does not seem to pick up on new fonts installed in Mac OS X. Is there a way to register new fonts I've installed with Wine? Would manually editing the system.reg file that seems to contain font mappings work, or is there something else I'd need to do? bump Bounty ends soon, I'm still looking for an answer for this. Does anyone use the Wine console for complex text user interfaces?

  Read the article

• MySQL taking a long time to start

  - by Dscoduc

  I'm running Windows Server 2008 with MySQL installed and every time I reboot the server the MySQL Service doesn't start right away. A look into the Windows Eventlog shows that the MySQL Service was hung at startup. Looking at the Services.msc console shows the service state at Starting... Eventually, like 10 minutes, the MySQL Service actually finishes the startup process and the database becomes available for my Wordpress server... I looked at the MySQL .err files and didn't find anything that would indicate a delay in the statup process... Can anyone suggest a way to determine what is causing the delay, and more importantly, how to prevent the delay in the MySQL Startup? UPDATE: Here is the .err log contents from the shutdown to the startup complete. Notice the startup begins at 10:30:00 and the MySQL isn't ready for connections until 10:47:14, a full 17 minutes later: 100322 10:27:06 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: Normal shutdown 100322 10:27:06 [Note] Event Scheduler: Purging the queue. 0 events 100322 10:27:06 InnoDB: Starting shutdown... 100322 10:27:08 InnoDB: Shutdown completed; log sequence number 4 3854351346 100322 10:27:08 [Warning] Forcing shutdown of 1 plugins 100322 10:27:08 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: Shutdown complete 100322 10:30:00 [Note] Plugin 'FEDERATED' is disabled. 100322 10:30:01 InnoDB: Started; log sequence number 4 3854351346 100322 10:47:14 [Note] Event Scheduler: Loaded 0 events 100322 10:47:14 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: ready for connections. UPDATE 2: MySQL is configured as a service (part of the install process, nothing I did) and executes the following syntax (as it appears in the registry): "C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld" --defaults-file="C:\Program Files\MySQL\MySQL Server 5.1\my.ini" MySQL

  Read the article

• Setup Entourage for Exchange via HTTP communication

  - by Johandk

  Our ISP set up a hosted exchange server for all our mail. I've setup all our Outlook users with no problems. We have two people using Mac OSX Leopard and Entourage. Entourage has the option of adding an Exchange account, but I have no idea how to tell it to connect to exchange via HTTP. Heres an excerpt from the client setup docs the hosting company sent me for Outlook: 1 .Go to control panel 2. Select ‘Mail’ 3. Select ‘Email accounts’ Under the E-mail tab select ‘New’ Select ‘Manually configure server settings......’ - click next Select ‘Microsoft Exchange’ – click next Complete details as below with Microsoft Exchange Server as: [server address] Do not select ‘Check Name’. Instead select ‘More Settings’. Go to the Connection tab, and select the bottom option ‘Connect to Microsoft Exchange using HTTP’. And then select the ‘Exchange Proxy Settings’ button. Enter Proxy server for Exchange Check Only connect to proxy servers that have this principal name in their certificate, Enter msstd:[servername] Proxy Authentication - select Basic Authentication Select OK, and again, so that you return to the main screen. Now select ‘Check Name’. Enter Username and Password: The username should now be the full name and underlined. If so select next, and then finish. Next time you open Outlook, enter username and password Any help GREATLY appreciated.

  Read the article

• What is the difference between Startup programs in windows and the same programs being started manually

  - by sup

  I am no Windows guy, but I am trying to get a seamless integration of Windows program through Virtual Box Windows guest onto my Ubuntu machine. I more or less followed this tutorial: https://nowhere.dk/articles/running-windows-applications-natively-with-seamlessrdp Basically I start up Windows in Virtual Box and then I try to launch an application (on Ubuntu host) like this: rdesktop -A -s "c:\Program Files\ThinLinc\WTSTools\seamlessrdpshell.exe notepad.exe" 192.168.123.103:3389 -u user -p password That just gives me full Windows desktop that I do not want. However, when I run (on the Windows guest) "c:\Program Files\ThinLinc\WTSTools\seamlessrdpshell.exe" "notepad" The command above works and I get just the window I want. Now, so I thought I would put this command into startup folder of the Windows machine and everything would be fine. But it says "Unable to set up the virtual channel". (by googling, I nailed it to this file: https://sourceforge.net/p/rdesktop/code/1686/tree/seamlessrdp/trunk/ServerExe/vchannel.c - the warning is triggered (by main.c in the same directory) when function vchannel_open() returns something that C interprets as yes for if condition). I have no idea why it works when I launch this command manually via a bat file and not when I put it to startup programs. Any ideas?

  Read the article

• Batch deletion of smaller files from group of files via unix command line

  - by artlung

  I have a large number (more than 400) of directories full of photos. What I want to do is to keep the larger sizes of these photos. Each directory has 31 to 66 files in it. Each directory has thumbnails, and larger versions, plus a file called example.jpg I dispatched the example.jpg file easily with: rm */example.jpg I initially thought that it would be easy to delete the thumbnails, but the problem is they are not consistently named. The typical pattern was photo1.jpg and photo1s.jpg. I did rm */photo*s.jpg but it ended up some of the files named photoXs.jpg were actually larger and not smaller. Argh. So what I want to do is scan each directory for filesize and delete (or move) the thumbnails. I initially thought I'd just ls -R every file and extract the size of each file and save those under a threshold. The problem? In one directory the large will be 1.1 MB and the thumb is 200k. In another the large is 200k and the small 30k. Even worse, the files really are mostly named photo1.jpg - so simply putting them all in the same folder, sorting by size, and deleting in groups would not work without renaming already, and if it's possible I'd prefer to keep them in their folders. I was almost resolved to just doing this all manually, but then thought I'd ask here. How would you do this task?

  Read the article

• Slow performance on VMWare Linux server after Tomcat install

  - by Loftx

  We have a VMWare ESXi 4.1 server hosting a number of Linux and Windows guests. Recently a new Linux guest was added to this server and seemed to be performing well. Tomcat and some other applications on this server were then installed which seem to have caused the server to run really slowly without any obvious resource issues. Slow performance include: The time taken to bring up the password prompt over ssh takes a few seconds when it was previously instantaneous. The time taken to unzip a zip file which was previously a few seconds now takes around 30 seconds The time taken to compile vmware tools has increased by similar factors Both the VMWare console and monitoring commands don't report any issues with high CPU or memory usage but something is obviously slowing the server down somehow. Does anyone have any ideas what may be causing this issue and how it can be resolved? Thanks, Tom Edit As per your questions I’ve looked at some of the performance indicators on both the VM host and VM guest indicated. Firstly I tried reserving the full amount of memory (3gb) for this VM – no other machines on this server have any memory reservation. The swap in rate and swap out rate for the VM host and guest are now both zero. Balloon memory on the guest is zero and on the host is 3.5gb (total memory on the host is 12gb) The swap rate for the guest is also zero. Swap used by the host is 200mb on average. Compression and decompression rates for the host and guest are zero. Command aborts for the host are zero. Read latency is very low – maximum 10ms average 0.8ms. Write latency is higher – a few spikes to 170ms but mostly around 25ms – is this bad? Queue command latency is zero . Physical disk read latency averages 5ms but often 10ms Physical disk write latency averages 15ms but is often 20ms I hope this helps - let me know if you need any more information.

  Read the article

• SQL 2005 Install completly broken on laptop.

  - by ProfKaos

  My problems started when I set up an exploratory domain controller at home. During that process, I changed the name of my laptop, from 'erisia' to 'erisia-laptop', and this resulted in me losing my admin account on SQL Server 2005 on my laptop. SQL Server seems to store the machine name as part of the user name, so now my local admin account is 'erisia-laptop\brady', which SQL server didn't recognise. I thought I'd cut my losses and just re-install SQL 2005, but the first install was aborted, so I tried a complete uninstall, followed by the new install. The latter didn't work while the former worked way too well. Now every attempt at installing SQL Server 2005 SP2 on my laptop running XP SP3 ends in sadness, with MSXML6 being the cause, because it won't install on this OS version. WTF? Does anyone know what I can do to get SQL 2005 installed? It's the only full admin DB tool I have. SQL 2008 Express that installed with VS 2010 Beta 2 doesn't allow much server admin.

  Read the article

• Can a hardware firewall block a server accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. Is this possible? Does 'UNC traffic' go out of the machine and then back in again?

  Read the article

• Missing Data on VMWare Virtual Disk

  - by Lachlan McDonald

  Evening all, I've got a considerable problem I'm hoping to get some resolution on. I had two VMWare 6.5 virtual machines, one running Ubuntu 9.10 and the other Ubuntu 10.04. I used 9.10 as a testing server, so I could install a LAMP environment to prepare some code. Over the months I took a number of snapshots of this VM just in case something went wrong, and did a full copy of the entire VM a month ago. I created the 10.04 VM when Lucid Lynx launched so I could continue development on a fresh install. To get the files over, I simply added the 9.10 virtual disk into the 10.04 VM, grabbed some of the files I needed, and dismounted it. Unknown to me at the time, the changes to the 9.04 virtual disk meant that I could no longer boot it with the 9.10 VM. I'd always get the "The parent virtual disk has been modified since the child was created." error. I decided this was a good time to backup all the critical files, but now whenever I open the 9.04 disk to get the data it isn't in the same state as it was earlier. My question is; is it possible when I'm mounting the virtual disk that I'm not seeing the most recent snapshot, or in my blundering, have I lost the virtual disk. Cheers

  Read the article

• Why I am getting "Problem loading the page" after enabling HTTPS for Apache on Windows 7?

  - by Anish

  I enabled HTTPS on the Apache server (2.2.15) Windows 7 Enterprise by uncommenting: Include /private/etc/apache2/extra/httpd-ssl.conf in C:\Program Files (x86)\Apache Software Foundation\Apache2.2\conf\httpd.conf and modifying C:\Program Files (x86)\Apache Software Foundation\Apache2.2\conf\httpd-ssl.conf to include: DocumentRoot "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/htdocs" ServerName myserver.com:443 ServerAdmin [email protected] ... SSLCertificateFile "SSLCertificateFile "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/conf/cert.pem SSLCertificateKeyFile "SSLCertificateFile "C:/Program Files (x86)/Apache Software Foundation/Apache2.2/conf/key.pem" Then I restart apache (going to start-All Progranms-Apache Server 2.2-Control-restart) and go to localhost on port 443 in Firefox , where I get: Index of / Index of / Links/ ..... .... But on Display of WebPage I see: Unable to connect Firefox can't establish a connection to the server at localhost. *The site could be temporarily unavailable or too busy. Try again in a few moments. *If you are unable to load any pages, check your computer's network onnection. *If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. I read: Why am I getting 403 Forbidden after enabling HTTPS for Apache on Mac OS X? and added default web server configuration block to match my DocumentRoot The error Log C:\Program Files (x86)\Apache Software Foundation\Apache2.2\logs\error.log gives following error: The Apache2.2 service is running. (OS 5)Access is denied. : Init: Can't open server certificate file C:/Program Files (x86)/Apache Software Foundation/Apache2.2/conf/cert.pem I checked the permissions for cert.pem and it indicates: All the permissions (Full control, Read, Read and modify, execute, Write) are marked for Admin and I am currently logged in as Admin. I tried using oldcert.pem and oldkey.pem on the same server and it works fine. Is there anything that I missed?

  Read the article

• SQL Server 2008 R2 mirroring failing

  - by andriusn

  I have two Windows 2008 R2 (Amazon EC2) instances running SQL Server 2008 R2. I use 9TB striped disks (9x1TB EBS volumes) for storage. One server is running as principal and second one as mirror. Both started from the same image, database and tlog files located on striped disk. Mirror server failed 3 times in last 2 months with errors: EventID 823 The operating system returned error 2(The system cannot find the file specified.) to SQL Server during a write at offset 0x00000048058a00 in file 'D:\TLogs***_log.ldf'. Additional messages in the SQL Server error log and system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC CHECKDB). This error can be caused by many factors; for more information, see SQL Server Books Online. and EventID 1454 Database mirroring will be suspended. Server instance 'xxxxxxxxxx' encountered error 823, state 6, severity 24 when it was acting as a mirroring partner for database '***'. The database mirroring partners might try to recover automatically from the error and resume the mirroring session. For more information, view the error log for additional error messages. followed by EventID 19019 The MSSQLSERVER service terminated unexpectedly. After this rebooting instance is necessary to restore mirroring. First two times I thought it was hardware related (striped disk failure) and relaunched instance on new hardware. But the issue is back after few weeks again. It only affects mirror instances. Any help would be really appreciated. Thanks.

  Read the article

• Can I have 2Gbit over 1Gbit Nics

  - by Daniel

  So this really baffles me. Apparently because 1Gbit can transmit data in both directions simultaneously it should be possible to get 2Gbit of data transfer on a single NIC (1Gbit flow seend and 1Gbit receive). People claim that because 1Gbit is full-duplex (almost always) it is exactly 2Gbit in total. My intuition and electrical background tells me that something is not right here 4 twisted pairs 250Mbit capacity each gives 1Gbit. Unless it is really possible to transfer data in both directions simultaneously. I did a test with iperf. Ubuntu server 12.04 <-- MacBook Pro. Both with decent CPU speed. Tested speed of connection individually and on Mac I can see 112MB/s regardless which direction data is going. On Ubuntu with vnstat and ifstat I got 970Mbit speeds. Now, launching iperf in server mode on both machines at the same time and sending data using 2 iperf clients shows that I'm for example on Ubuntu box sending at 600Mbit, and receiving 350Mbit. which adds up to pretty much 1Gbit link. So to me there is no magical 2Gbit. Can someone confirm that or tell why I'm wrong? Another thing that confuses me i the fact that e.g. 24-port switch has for example: Throughput»up»to:»50.6Mpps Switching»capacity:»68Gbps Switch»fabric»speed:»88Gbps Which would suggest thay can handle 2GBit per port.

  Read the article

• New hard drive for backup? [closed]

  - by glaeven

  I have come to realize that I need another external drive to use with my MacBook Pro. I currently have a 1TB WD MyBook Essential that I have been using for about a year and a half. I have it currently partitioned into two drives, one for backup (I named it Leonov) and one for movies, TV shows and other large files I don't need very often (I call that side Discovery One). I use Time Machine for backups since it is completely automated and I can restore from it without much trouble (I have had to at least three times now). As of now, Leonov is full enough that every backup deletes an old one and Discovery One is approaching it's limits. I would like to get a new drive and move one of the sides to it. What are some reliable, external (~1TB) drives for under or around $100? Would it be easier to move the movies (et al.) or the backups to the new drive? I also feel like I should say that all of my important documents (for school and the like, just not my music) are also synced to Dropbox as another form of backup and access.

  Read the article

• Vmware Workstation downloads as a txt file?

  - by George Mauer

  I just went to the vmware website because I want to try workstation over virtualbox. I signed up for a workstation trial and clicked download on the 64bit linux version. What downloaded is a 320 megabyte txt file VMware-Workstation-Full-8.0.2-591240.x86_64.txt What gives? Is anyone familiar with this pattern of delivering software? How do I run it? Here is the beginning of that file: #!/usr/bin/env bash # # VMware Installer Launcher # # This is the executable stub to check if the VMware Installer Service # is installed and if so, launch it. If it is not installed, the # attached payload is extracted, the VMIS is installed, and the VMIS # is launched to install the bundle as normal. # Architecture this bundle was built for (x86 or x64) ARCH=x64 if [ -z "$BASH" ]; then # $- expands to the current options so things like -x get passed through if [ ! -z "$-" ]; then opts="-$-" fi # dash flips out of $opts is quoted, so don't. exec /usr/bin/env bash $opts "$0" "$@" echo "Unable to restart with bash shell" exit 1 fi set -e ETCDIR=/etc/vmware-installer OLDETCDIR="/etc/vmware" ### Offsets ### # These are offsets that are later used relative to EOF. FOOTER_SIZE=52 # This won't work with non-GNU stat. FILE_SIZE=`stat --format "%s" "$0"` offset=$(($FILE_SIZE - 4)) MAGIC_OFFSET=$offset offset=$(($offset - 4)) CHECKSUM_OFFSET=$offset offset=$(($offset - 4)) VERSION_OFFSET=$offset offset=$(($offset - 4)) PREPAYLOAD_OFFSET=$offset

  Read the article

• Setup.exe called from a batch file crashes with error 0x0000006

  - by Alex

  We're going to be installing some new software on pretty much all of our computers and I'm trying to setup a GPO to do it. We're running a Windows Server 2008 R2 domain controller and all of our machines are Windows 7. The GPO calls the following script which sits on a network share on our file server. The script it self calls an executable that sits on another network share on another server. The executable will imediatelly crash with an error 0x0000006. The event log just says this: Windows cannot access the file for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program Setup.exe because of this error. Here's the script (which is stored on \\WIN2K8R2-F-01\Remote Applications): @ECHO OFF IF DEFINED ProgramFiles(x86) ( ECHO DEBUG: 64-bit platform SET _path="C:\Program Files (x86)\Canam" ) ELSE ( ECHO DEBUG: 32-bit platform SET _path="C:\Program Files\Canam" ) IF NOT EXIST %_path% ( ECHO DEBUG: Folder does not exist PUSHD \\WIN2K8R2-PSA-01\PSA Data\Client START "" "Setup.exe" "/q" POPD ) ELSE ( ECHO DEBUG: Folder exists ) Running the script manually as administrator also results in the same error. Setting up a shortcut with the same target and parameters works perfectly. Manually calling the executable also works. Not sure if it matters, but the installer is based on dotNETInstaller. I don't know what version though. I'd appreciate any suggestions on fixing this. Thanks in advance! UPDATE I highly doubt this matters, but the network share that the script is hosted in is a shared drive, while the network share the script references for the executable is a shared folder. Also, both shares have Domain Computers listed with full access for the sharing and security tabs. And PUSHD works without wrapping the path in quotes.

  Read the article

• How do I handle a request for "index.php/somepath" in Nginx config?

  - by Arne

  I'm currently attempting to serve Icinga from nginx. The new Icinga-Web ui attempts to load a file from URL http://SERVER/icinga-web/index.php/appkit/squishloader/javascript (leading to a 404). How do I setup a location for this scenario? How do I get nginx to serve index.php and pass the full request path in a way Icinga understands? This is my current nginx config for icinga (adapted from the default apache config): server { server_name SERVER; root /opt/icinga/icinga-1.2.1; location /icinga-web/js/ext3 { alias /opt/icinga/icinga-1.2.1/lib/ext3; } location /icinga-web { alias /opt/icinga/icinga-1.2.1/pub; } location /icinga/cgi-bin { alias /opt/icinga/icinga-1.2.1/sbin; } location /icinga { alias /opt/icinga/icinga-1.2.1/share; } location ~ \.php([\?/].*)?$ { include fastcgi_params; fastcgi_pass 127.0.0.1:61000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } Any thoughts? Thanks!

  Read the article

• SQL Server Agent refuses to start

  - by Geo Ego

  I'm having a problem with SQL Server 2005 where the SQL Server Agent suddenly refuses to start. If I attempt to start it through Services, I get the error "SQL Server Agent (MSSQLSERVER) service on Local Computer started and then stopped." In the Application log, I have the following entry: Event Type: Error Event Source: SQLSERVERAGENT Event Category: Service Control Event ID: 103 Date: 5/20/2010 Time: 11:07:07 AM User: N/A Computer: SHAREPOINT Description: SQLServerAgent could not be started (reason: Unable to connect to server 'SHAREPOINT'; SQLServerAgent cannot start). This database has been running fine for four months. It contains a SharePoint configuration database, which two days ago stopped working, throwing me a message that the configuration database cannot be reached. It was then that I realized the SQL Server Agent was not running, and I have been unable to restart it. I have tried running it with both the local system account and the network service account, with the same results. So far, I have tried: Granting the administrators group, network service, and SharePoint SQL Server Agent account public and sysadmin roles on the database. Granting the administrators group, network service, and SharePoint SQL Server Agent account full permissions to the entire MSSQL directory and all files within. I still have no joy.

  Read the article

• Bad sectors, S.M.A.R.T., SpinRite, firmware on platter and drive id questions.

  - by Christopher Galpin

  Is it possible for S.M.A.R.T. to give false readings (say I was fiddling with lots of recovery programs, transfers, so on and so forth) or is it absolutely a read-only direct correlation to the physical status of a drive? Does SpinRite level 5 "recover bad sectors" operate on those marked at the factory? Are they on the same level as your generic bad sector, with SpinRite thus having full access? (Also I'm curious if SMART's bad sector count is zero'd afterward or if it includes factory marked sectors.) The main firmware of some drives, like a WD Passport is stored on the platter. How is it protected? Is it through marking them as bad sectors? If so, I'm wondering if SpinRite's sector recovery could bring about firmware corruption on these drives. Is the failure of a drive to report valid identity information (hdparm -I /dev/xx) consistent with corrupted firmware, or just general disk failure? I may be misunderstanding the role of firmware here. I feel I've read a drive's identity information is on the platter, just like the partition tables and so on. Is this true? (Apologizes if this is more appropriate for SuperUser.)

  Read the article

< Previous Page | 433 434 435 436 437 438 439 440 441 442 443 444  | Next Page >