Search Results

Search found 29938 results on 1198 pages for 'version hunter'.

Page 439/1198 | < Previous Page | 435 436 437 438 439 440 441 442 443 444 445 446  | Next Page >

• Need help partitioning when reinstalling Ubuntu 14.04

  - by Chris M.

  I upgraded to 14.04 about a month ago on my HP Mini netbook (about 16 GB hard disk). A few days ago the system crashed (I don't know why but I was using internet at the time). When I restarted the computer, Ubuntu would not load. Instead, I got a message from the BIOS saying Reboot and Select proper Boot device or Insert Boot Media in selected Boot device and press a key I took this to mean that I needed to reinstall 14.04. When I try to reinstall Ubuntu from the USB stick, I choose "Erase disk and install Ubuntu" but then I get a message: Some of the partitions you created are too small. Please make the following partitions at least this large: / 3.3 GB If you do not go back to the partitioner and increase the size of these partitions, the installation may fail. At first I hit Continue to see if it would install anyway, and it gave the message: The attempt to mount a file system with type ext4 in SCSI1 (0,0,0), partition # 1 (sda) at / failed. You may resume partitioning from the partitioning menu. The second time I hit Go Back, and it took me to the following partitioning table: Device Type Mount Point Format Size Used System /dev/sda /dev/sda1 ext4 (checked) 3228 MB Unknown /dev/sda5 swap (not checked) 1063 MB Unknown + - Change New Partition Table... Revert Device for boot loader installation: /dev/sda ATA JM Loader 001 (4.3 GB) At this point I'm not sure what to do. I've never partitioned my hard drive before and I don't want to screw things up. (I'm not particularly tech savvy.) Can you instruct me what I should do. (P.S. I'm afraid the table might not appear as I typed it in.) Results from fdisk: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 4294 MB, 4294967296 bytes 255 heads, 63 sectors/track, 522 cylinders, total 8388608 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda doesn't contain a valid partition table Disk /dev/sdb: 7860 MB, 7860125696 bytes 155 heads, 31 sectors/track, 3194 cylinders, total 15351808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009a565 Device Boot Start End Blocks Id System /dev/sdb1 * 2768 15351807 7674520 b W95 FAT32 ubuntu@ubuntu:~$ Here is what it displays when I open the Disks utility (I tried the screenshot terminal command you suggested but it didn't seem to do anything): 4.3 GB Hard Disk /dev/sda Model: JM Loader 001 (01000001) Size: 4.3 GB (4,294,967,296 bytes) Serial Number: 01234123412341234 Assessment: SMART is not supported Volumes Size: 4.3 GB (4,294,967,296 bytes) Device: /dev/sda Contents: Unknown (There is a button in the utility that when you click it gives the following options: Format... Create Disk Image... Restore Disk Image... Benchmark but SMART Data & Self-Tests... is dimmed out) When I hit F9 Change Boot Device Order, it shows the hard drive as: SATA:PM-JM Loader 001 When I hit F10 to get me into the BIOS Setup Utility, under Diagnostic it shows: Primary Hard Disk Self Test Not Support NetworkManager Tool State: disconnected Device: eth0 Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 00:26:55:B0:7F:0C Capabilities: Carrier Detect: yes Wired Properties Carrier: off When I run command lshw -C network, I get: WARNING: you should run this program as super-user. *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:16 memory:feafc000-feafffff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: c0 serial: 00:26:55:b0:7f:0c capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:febc0000-febfffff ioport:ec80(size=128) WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• How do I get to work my Atheros AR9485 Wireless card in Ubuntu 14.04 LTS?

  - by Ivan Kreimer

  I've recently installed Ubuntu 14.04 LTS in my ASUS D550CA, and so far things have gone great. The only problem I've got is the Wi-Fi. It doesn't work. I've got an Qualcomm Atheros AR9485. I've tried installing the drivers, but the sytem says it doesn't find any. So I started looking around this forum for solutions. I've read every single post from this forum about my Wi-Fi network adapter, and I've found nothing that solves my problem. Let me give you some info about my configuration. Disclaimer: my configuration is in spanish, so if you don't understand something you can either use Google translate, or use your imagination. :D When I run $ sudo lshw -C network this is what I get: *-network DEACTIVATED descripción: Interfaz inalámbrica producto: AR9485 Wireless Network Adapter fabricante: Qualcomm Atheros id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: wlan0 versión: 01 serie: 28:e3:47:5c:5d:3f anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.13.0-34-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:f7d00000-f7d7ffff memoria:f7d80000-f7d8ffff *-network descripción: Ethernet interface producto: RTL8101E/RTL8102E PCI Express Fast Ethernet controller fabricante: Realtek Semiconductor Co., Ltd. id físico: 0.2 información del bus: pci@0000:03:00.2 nombre lógico: eth0 versión: 06 serie: e0:3f:49:ce:57:49 tamaño: 100Mbit/s capacidad: 100Mbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8402-1_0.0.1 10/26/11 ip=181.165.245.39 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s recursos: irq:41 ioport:e000(size=256) memoria:f0004000-f0004fff memoria:f0000000-f0003fff At the beginning, you'll see that it says "*-network DEACTIVATED" (or at least that's what I translated), is that something bad? Then, when I run ipconfig this is what I get: eth0 Link encap:Ethernet direcciónHW e0:3f:49:ce:57:49 Direc. inet:181.165.245.39 Difus.:181.165.245.255 Másc:255.255.255.0 Dirección inet6: fe80::e23f:49ff:fece:5749/64 Alcance:Enlace ACTIVO DIFUSIÓN FUNCIONANDO MULTICAST MTU:1500 Métrica:1 Paquetes RX:221199 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:62025 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:124409589 (124.4 MB) TX bytes:7471899 (7.4 MB) lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:65536 Métrica:1 Paquetes RX:2977 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:2977 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:397158 (397.1 KB) TX bytes:397158 (397.1 KB) When I put iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Finally, when I put sudo rfkill list all, I got: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no I hope anyone can help me solve this, I've searched a lot and found no solution. Thanks a lot.

  Read the article

• Customizing the Test Status on the TFS 2010 SSRS Stories Overview Report

  - by Bob Hardister

  This post shows how to customize the SQL query used by the Team Foundation Server 2010 SQL Server Reporting Services (SSRS) Stories Overview Report. The objective is to show test status for the current version while including user story status of the current and prior versions.  Why? Because we don’t copy completed user stories into the next release. We only want one instance of a user story for the product because we believe copies can get out of sync when they are supposed to be the same. In the example below, work items for the current version are on the area path root and prior versions are not on the area path root. However, you can use area path or iteration path criteria in the query as suits your needs. In any case, here’s how you do it: 1. Download a copy of the report RDL file as a backup 2. Open the report by clicking the edit down arrow and selecting “Edit in Report Builder” 3. Right click on the dsOverview Dataset and select Dataset Properties 4. Update the following SQL per the comments in the code: Customization 1 of 3 … -- Get the list deliverable workitems that have Test Cases linked DECLARE @TestCases Table (DeliverableID int, TestCaseID int); INSERT @TestCases     SELECT h.ID, flh.TargetWorkItemID     FROM @Hierarchy h         JOIN FactWorkItemLinkHistory flh             ON flh.SourceWorkItemID = h.ID                 AND flh.WorkItemLinkTypeSK = @TestedByLinkTypeSK                 AND flh.RemovedDate = CONVERT(DATETIME, '9999', 126)                 AND flh.TeamProjectCollectionSK = @TeamProjectCollectionSK         JOIN [CurrentWorkItemView] wi ON flh.TargetWorkItemID = wi.[System_ID]                  AND wi.[System_WorkItemType] = @TestCase             AND wi.ProjectNodeGUID  = @ProjectGuid              --  Customization 1 of 3: only include test status information when test case area path = root. Added the following 2 statements              AND wi.AreaPath = '{the root area path of the team project}'  …          Customization 2 of 3 … -- Get the Bugs linked to the deliverable workitems directly DECLARE @Bugs Table (ID int, ActiveBugs int, ResolvedBugs int, ClosedBugs int, ProposedBugs int) INSERT @Bugs     SELECT h.ID,         SUM (CASE WHEN wi.[System_State] = @Active THEN 1 ELSE 0 END) Active,         SUM (CASE WHEN wi.[System_State] = @Resolved THEN 1 ELSE 0 END) Resolved,         SUM (CASE WHEN wi.[System_State] = @Closed THEN 1 ELSE 0 END) Closed,         SUM (CASE WHEN wi.[System_State] = @Proposed THEN 1 ELSE 0 END) Proposed     FROM @Hierarchy h         JOIN FactWorkItemLinkHistory flh             ON flh.SourceWorkItemID = h.ID             AND flh.TeamProjectCollectionSK = @TeamProjectCollectionSK         JOIN [CurrentWorkItemView] wi             ON wi.[System_WorkItemType] = @Bug             AND wi.[System_Id] = flh.TargetWorkItemID             AND flh.RemovedDate = CONVERT(DATETIME, '9999', 126)             AND wi.[ProjectNodeGUID] = @ProjectGuid              --  Customization 2 of 3: only include test status information when test case area path = root. Added the following statement              AND wi.AreaPath = '{the root area path of the team project}'       GROUP BY h.ID … Customization 2 of 3 … -- Add the Bugs linked to the Test Cases which are linked to the deliverable workitems -- Walks the links from the user stories to test cases (via the tested by link), and then to -- bugs that are linked to the test case. We don't need to join to the test case in the work -- item history view. -- --    [WIT:User Story/Requirement] --> [Link:Tested By]--> [Link:any type] --> [WIT:Bug] INSERT @Bugs SELECT tc.DeliverableID,     SUM (CASE WHEN wi.[System_State] = @Active THEN 1 ELSE 0 END) Active,     SUM (CASE WHEN wi.[System_State] = @Resolved THEN 1 ELSE 0 END) Resolved,     SUM (CASE WHEN wi.[System_State] = @Closed THEN 1 ELSE 0 END) Closed,     SUM (CASE WHEN wi.[System_State] = @Proposed THEN 1 ELSE 0 END) Proposed FROM @TestCases tc     JOIN FactWorkItemLinkHistory flh         ON flh.SourceWorkItemID = tc.TestCaseID         AND flh.RemovedDate = CONVERT(DATETIME, '9999', 126)         AND flh.TeamProjectCollectionSK = @TeamProjectCollectionSK     JOIN [CurrentWorkItemView] wi         ON wi.[System_Id] = flh.TargetWorkItemID         AND wi.[System_WorkItemType] = @Bug         AND wi.[ProjectNodeGUID] = @ProjectGuid         --  Customization 3 of 3: only include test status information when test case area path = root. Added the following statement         AND wi.AreaPath = '{the root area path of the team project}'     GROUP BY tc.DeliverableID … 5. Save the report and you’re all set. Note: you may need to re-apply custom parameter changes like pre-selected sprints.

  Read the article

• My LAN USB NIC is not working in ubuntu 11.10?

  - by Gaurav_Java

  Today i start my system its seems that my LAN port is not working . so i buy one USB to LAN adapter and i plug in ubuntu system its doen't connect automatically .when i check result lsusb its shows me that there is one DM9601 Ethernet adapter is connected when i click on network information in panel its shows me that there is something " wired NEtwork (Broadcom NetLink BCM5784M gigabit Ethernet PCIe) I think want some driver for that .i don't have any idea how it can be used ? here output of sudo lspci -nn *00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07) 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) 00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07) 00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03) 00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03) 00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03) 00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03) 00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03) 00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03) 00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03) 00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03) 00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03) 00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03) 00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93) 00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03) 00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03) 00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03) 02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) 04:00.0 Network controller [0280]: Intel Corporation WiFi Link 5100 [8086:4232]* sudo lshw -class network *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 00:1f:16:9a:56:98 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:f4500000-f450ffff *-network DISABLED description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fa:09:02:00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-17-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:46 memory:f4600000-f4601fff *-network description: Ethernet interface physical id: 4 logical name: eth1 serial: 00:60:6e:00:f1:7d size: 100Mbit/s capacity: 100Mbit/s capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=dm9601 driverversion=22-Aug-2005 duplex=full firmware=Davicom DM9601 USB Ethernet ip=192.168.1.34 link=yes multicast=yes port=MII speed=100Mbit/s I am using Wimax internet connection which i have to connect from browser . at that time my system is not showing that i am connected to any wired connection. but when i connect internet from other system after getting conneted to internet . when i plug again my USB LAN then its shows that you are conneted to wired connetion. here is screenshot for conneting wimax from browser after connecting to internet network connection shows

  Read the article

• No Wireless Networks, BCM4313 [duplicate]

  - by TalonPlz

  This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

  Read the article

• Hyper-V for Developers Part 1 Internal Networks

  Over the last year, weve been working with Microsoft to build training and demo content for the next version of Office Communications Server code-named Microsoft Communications Server 14.  This involved building multi-server demo environments in Hyper-V, getting them running on demo servers which we took to TechEd, PDC, and other training events, and sometimes connecting the demo servers to the show networks at those events.  ITPro stuff that should scare the hell out of a developer! It can get ugly when I occasionally have to venture into ITPro land.  Lets leave it at that. Having gone through this process about 10 to 15 times in the last year, I finally have it down.  This blog series is my attempt to put all that knowledge in one place if anything, so I can find it somewhere when I need it again.  Ill start with the most simple scenario and then build on top of it in future blog posts. If youre an ITPro, please resist the urge to laugh at how trivial this is. Internal Hyper-V Networks Lets start simple.  An internal network is one that intended only for the virtual machines that are going to be on that network it enables them to communicate with each other. Create an Internal Network On your host machine, fire up the Hyper-V Manager and click the Virtual Network Manager in the Actions panel. Select Internal and leave all the other default values. Give the virtual network a name, and leave all the other default values. After the virtual network is created, open the Network and Sharing Center and click Change Adapter Settings to see the list of network connections. The only thing I recommend that you do is to give this connection a friendly label, e.g. Hyper-V Internal.  When you have multiple networks and virtual networks on the host machines, this helps group the networks so you can easily differentiate them from each other.  Otherwise, dont touch it, only bad things can happen. Connect the Virtual Machines to the Internal Network Im assuming that you have more than 1 virtual machine already configured in Hyper-V, for example a Domain Controller, and Exchange Server, and a SharePoint Server. What you need to do is basically plug in the network to the virtual machine.  In order to do this, the machine needs to have a virtual network adapter.  If the VM doesnt have a network adapter, open the VMs Settings and click Add Hardware in the left pane.  Choose the virtual network to which to bind the adapter to. If you already have a virtual network adapter on the VM, simply connect it to the virtual network. Assign IP Addresses to the Virtual Machines on the Internal Network Open the Network and Sharing Center on your VM, there should only be 1 network at this time.  Open the Properties of the connection, select Internet Protocol Version 4 (TCP/IPv4) and hit Properties. In this environment, Im assigning IP addresses as 192.168.0.xxx.  This particular VM has an IP address of 192.168.0.40 with a subnet mask of 255.255.255.0, and a DNS Server of 192.168.0.18.  DNS is running on the Domain Controller VM which has an IP address of 192.168.0.18. Repeat this process on every VM in your environment, obviously assigning a unique IP address to each.  In an environment with a domain controller, you should now be able to ping the machines from each other. What Next? After completing this process, heres what you still cannot do: Access the internet from any of the VMs Remote desktop to a VM from the host Remote desktop to a VM over the network In the next post, well take a look configuring an External network adapter on the virtual machines.  Well then build on top of that so that you can RDP into the VMs from the host machine and over the network.Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Upgraded to 12.04 now wifi doesn't work

  - by Benito Kestelman

  My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

  Read the article

• trying to setup wireless

  - by JohnMerlino

  I'm trying to set up wireless on vostro 1520 dell laptop, with latest Ubuntu install. Here's the output of some of the commands that I was told to run: lshw -C network viggy@ubuntu:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 03 serial: 00:24:e8:da:84:25 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.2.6 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:47 ioport:3000(size=256) memory:f6004000-f6004fff memory:f6000000-f6003fff memory:f6020000-f603ffff *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0e:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:fa000000-fa003fff *-network DISABLED description: Wireless interface physical id: 1 logical name: wlan0 serial: 0c:60:76:05:ee:74 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-29-generic firmware=N/A multicast=yes wireless=IEEE 802.11bg lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 1a:00.0 FireWire (IEEE 1394): O2 Micro, Inc. Device 10f7 (rev 01) 1a:00.1 SD Host controller: O2 Micro, Inc. Device 8120 (rev 01) 1a:00.2 Mass storage controller: O2 Micro, Inc. Device 8130 (rev 01) iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extensions. At this point in time, I don't have wireless.

  Read the article

• ReSharper 8.0 EAP now available

  - by TATWORTH

  Originally posted on: http://geekswithblogs.net/TATWORTH/archive/2013/06/28/resharper-8.0-eap-now-available.aspxJetbrains have just released |ReSharper 8.0 Beta on their Early Access |Programme at http://www.jetbrains.com/resharper/whatsnew/?utm_source=resharper8b&utm_medium=newsletter&utm_campaign=resharper&utm_content=customersResharper 8.0 comes with the following new features:Support for Visual Studio 2013 Preview. Yes, ReSharper is known to work well with the fresh preview of Visual Studio 2013, and if you have already started digging into it, ReSharper 8.0 Beta is ready for the challenge.Faster code fixes. Thanks to the new Fix in Scope feature, you can choose to batch-fix some of the code issues that ReSharper detects in the scope of a project or the whole solution. Supported fixes include removing unused directives and redundant casts.Project dependency viewer. ReSharper is now able to visualize a project dependency graph for a bird's eye view of dependencies within your solution, all without compiling anything!Multifile templates. ReSharper's file templates can now be expanded to generate more than one file. For instance, this is handy for generating pairs of a main logic class and a class for extensions, or sets of partial files.Navigation improvements. These include a new action called Go to Everything to let you search for a file, type or method name from the same input box; support for line numbers in navigation actions; a new tool window called Assembly Explorer for browsing through assemblies; and two more contextual navigation actions: Navigate to Generic Substitutions and Navigate to Assembly Explorer.New solution-wide refactorings. The set of fresh refactorings is headlined by the highly requested Move Instance Method to move methods between classes without making them static. In addition, there are Inline Parameter and Pull Parameter. Last but not least, we're also introducing 4 new XAML-specific refactorings!Extraordinary XAML support. A plethora of new and improved functionality for all developers working with XAML code includes dedicated grid inspections and quick-fixes; Extract Style, Extract, Move and Inline Resource refactorings; atomic renaming of dependency properties; and a lot more.More accessible code completion. ReSharper 8 makes more of its IntelliSense magic available in automatic completion lists, including extension methods and an option to import a type. We're also introducing double completion which gives you additional completion items when you press the corresponding shortcut for the second time.A new level of extensibility. With the new NuGet-based Extension Manager, discovering, installing and uninstalling ReSharper extensions becomes extremely easy in Visual Studio 2010 and higher. When we say extensions, we mean not only full-fledged plug-ins but also sets of templates or SSR patterns that can now be shared much more easily.CSS support improvements. Smarter usage search for CSS attributes, new CSS-specific code inspections, configurable support for CSS3 and earlier versions, compatibility checks against popular browsers - there's a rough outline of what's new for CSS in ReSharper 8.A command-line version of ReSharper. ReSharper 8 goes beyond Visual Studio: we now provide a free standalone tool with hundreds of ReSharper inspections and additionally a duplicate code finder that you can integrate with your CI server or version control system.Multiple minor improvements in areas such as decompiling and code formatting, as well as support for the Blue Theme introduced in Visual Studio 2012 Update 2.

  Read the article

• Getting Audio from a Zone

  - by bleonard

  Now that I have Firefox and Java Web Start running from a zone, the last piece of the puzzle was audio (essential because most Flash content is accompanied by sound).  In the global zone there's a nice little utility called audiotest for testing your sound: bleonard@solaris:~$ audiotest Sound subsystem and version: SunOS Audio 4.0 (0x00040003) Platform: SunOS 5.11 snv_151a i86pc *** Scanning sound adapter #1 *** /dev/sound/audio810:0dsp (audio engine 0): audio810#0 - Performing audio playback test... <left> ................OK <right> ...............OK <stereo> ..............OK <measured sample rate 47727.00 Hz (-0.57%)> *** All tests completed OK *** Of course, before you can try audiotest in a zone, it must be installed: root@myzone:~# pkg install audio-utilities Packages to install: 1 Create boot environment: No DOWNLOAD PKGS FILES XFER (MB) Completed 1/1 6/6 0.4/0.4 PHASE ACTIONS Install Phase 20/20 PHASE ITEMS Package State Update Phase 1/1 Image State Update Phase 2/2 However, we'll need to do more than just install audiotest: root@myzone:~# audiotest /dev/mixer: No such file or directory The device file is missing from /dev. The audio devices also need to be added to the zone. For this we modify the zone configuration as follows: bleonard@solaris:~$ sudo zonecfg -z myzone Password: zonecfg:myzone> add device zonecfg:myzone:device> set match=/dev/audio* zonecfg:myzone:device> end zonecfg:myzone> add device zonecfg:myzone:device> set match=/dev/sound/* zonecfg:myzone:device> end zonecfg:myzone> add device zonecfg:myzone:device> set match=/dev/mixer* zonecfg:myzone:device> end zonecfg:myzone> add device zonecfg:myzone:device> set match=/dev/sndstat zonecfg:myzone:device> end zonecfg:myzone> verify zonecfg:myzone> exit Then reboot the zone: bleonard@solaris:~$ sudo zoneadm -z myzone reboot After which, audiotest should work: root@myzone:~# audiotest Sound subsystem and version: SunOS Audio 4.0 (0x00040003) Platform: SunOS 5.11 snv_151a i86pc *** Scanning sound adapter #1 *** /dev/sound/audio810:0dsp (audio engine 0): audio810#0 - Performing audio playback test... <left> ................OK <right> ...............OK <stereo> ..............OK <measured sample rate 48208.00 Hz (0.43%)> *** All tests completed OK *** You can also examine /dev/sndstat for additional information: root@myzone:~# cat /dev/sndstat SunOS Audio Framework Audio Devices: 0: audio810#0 Intel AC'97, ICH (DUPLEX) Mixers: 0: audio810#0 Intel AC'97, ICH AC'97 codec: SigmaTel STAC9700 However, when testing the sound from Firefox (from a user account other than root), such as this recent Flash presentation on Solaris availability, you may still be disappointed. This is simply a permissions problem, as the devices only have read and write permissions for root: root@myzone:~# ls -l /dev/audio* crw------- 1 root root 99, 3 Jul 1 10:21 /dev/audio crw------- 1 root root 99, 4 Jul 1 10:21 /dev/audioctl To address this: root@myzone:~# chmod 777 /dev/audio* root@myzone:~# chmod 777 /dev/sound/* And you should be all set.

  Read the article

• How do I get 5.1 surround sound working on an Acer Aspire 5738ZG?

  - by kbargais_LV

  I got a problem with sound. I tried everything but no results. :( I got 3 sound ports. my daemon: # This file is part of PulseAudio. # # PulseAudio is free software; you can redistribute it and/or modify # it under the terms of the GNU Lesser General Public License as published by # the Free Software Foundation; either version 2 of the License, or # (at your option) any later version. # # PulseAudio is distributed in the hope that it will be useful, but # WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU # General Public License for more details. # # You should have received a copy of the GNU Lesser General Public License # along with PulseAudio; if not, write to the Free Software # Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 # USA. ## Configuration file for the PulseAudio daemon. See pulse-daemon.conf(5) for ## more information. Default values are commented out. Use either ; or # for ## commenting. ; daemonize = no ; fail = yes ; allow-module-loading = yes ; allow-exit = yes ; use-pid-file = yes ; system-instance = no ; local-server-type = user ; enable-shm = yes ; shm-size-bytes = 0 # setting this 0 will use the system-default, usually 64 MiB ; lock-memory = no ; cpu-limit = no ; high-priority = yes ; nice-level = -11 ; realtime-scheduling = yes ; realtime-priority = 5 ; exit-idle-time = 20 ; scache-idle-time = 20 ; dl-search-path = (depends on architecture) ; load-default-script-file = yes ; default-script-file = /etc/pulse/default.pa ; log-target = auto ; log-level = notice ; log-meta = no ; log-time = no ; log-backtrace = 0 resample-method = speex-float-1 ; enable-remixing = yes ; enable-lfe-remixing = no flat-volumes = no ; rlimit-fsize = -1 ; rlimit-data = -1 ; rlimit-stack = -1 ; rlimit-core = -1 ; rlimit-as = -1 ; rlimit-rss = -1 ; rlimit-nproc = -1 ; rlimit-nofile = 256 ; rlimit-memlock = -1 ; rlimit-locks = -1 ; rlimit-sigpending = -1 ; rlimit-msgqueue = -1 ; rlimit-nice = 31 ; rlimit-rtprio = 9 ; rlimit-rttime = 1000000 ; default-sample-format = s16le ; default-sample-rate = 44100 ; default-sample-channels = 6 ; default-channel-map = front-left,front-right default-fragments = 8 default-fragment-size-msec = 10 ; enable-deferred-volume = yes ; deferred-volume-safety-margin-usec = 8000 ; deferred-volume-extra-delay-usec = 0

  Read the article

• Drivers for Atheros AR928X?

  - by Pato7

  I am new in Ubuntu and I had a big trouble with wifi. My ubuntu 12.10 doesn't detect my wifi card and I can't toggle the "activate wireless" option on the tasks bar (it is grey). I searched for drivers to make it work, but nothing worked for me. Can anyone give me a hand? Many thanks in advanced! lspci output 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV710 [Mobility Radeon HD 4500/5100 Series] 01:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI RV710/730 HDMI Audio [Radeon HD 4000 series] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8057 PCI-E Gigabit Ethernet Controller (rev 10) 03:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) 0c:03.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 0c:03.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 0c:03.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) lshw -c network output *-network descripción: Ethernet interface producto: 88E8057 PCI-E Gigabit Ethernet Controller fabricante: Marvell Technology Group Ltd. id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: eth0 versión: 10 serie: 00:24:be:83:b2:4f tamaño: 100Mbit/s capacidad: 1Gbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.123 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s recursos: irq:45 memoria:d3520000-d3523fff ioport:c000(size=256) memoria:d3500000-d351ffff *-network DESACTIVADO descripción: Interfaz inalámbrica producto: AR928X Wireless Network Adapter (PCI-Express) fabricante: Atheros Communications Inc. id físico: 0 información del bus: pci@0000:03:00.0 nombre lógico: wlan0 versión: 01 serie: 2c:81:58:e6:b6:03 anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.5.0-18-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:d2100000-d210ffff rfkill list all output 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: sony-wifi: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• Violation of the DRY Principle

  - by Onorio Catenacci

  I am sure there's a name for this anti-pattern somewhere; however I am not familiar enough with the anti-pattern literature to know it. Consider the following scenario: or0 is a member function in a class. For better or worse, it's heavily dependent on class member variables. Programmer A comes along and needs functionality like or0 but rather than calling or0, Programmer A copies and renames the entire class. I'm guessing that she doesn't call or0 because, as I say, it's heavily dependent on member variables for its functionality. Or maybe she's a junior programmer and doesn't know how to call it from other code. So now we've got or0 and c0 (c for copy). I can't completely fault Programmer A for this approach--we all get under tight deadlines and we hack code to get work done. Several programmers maintain or0 so it's now version orN. c0 is now version cN. Unfortunately most of the programmers that maintained the class containing or0 seemed to be completely unaware of c0--which is one of the strongest arguments I can think of for the wisdom of the DRY principle. And there may also have been independent maintainance of the code in c. Either way it appears that or0 and c0 were maintained independent of each other. And, joy and happiness, an error is occurring in cN that does not occur in orN. So I have a few questions: 1.) Is there a name for this anti-pattern? I've seen this happen so often I'd find it hard to believe this is not a named anti-pattern. 2.) I can see a few alternatives: a.) Fix orN to take a parameter that specifies the values of all the member variables it needs. Then modify cN to call orN with all of the needed parameters passed in. b.) Try to manually port fixes from orN to cN. (Mind you I don't want to do this but it is a realistic possibility.) c.) Recopy orN to cN--again, yuck but I list it for sake of completeness. d.) Try to figure out where cN is broken and then repair it independently of orN. Alternative a seems like the best fix in the long term but I doubt the customer will let me implement it. Never time or money to fix things right but always time and money to repair the same problem 40 or 50 times, right? Can anyone suggest other approaches I may not have considered? If you were in my place, which approach would you take? If there are other questions and answers here along these lines, please post links to them. I don't mind removing this question if it's a dupe but my searching hasn't turned up anything that addresses this question yet. EDIT: Thanks everyone for all the thoughtful responses. I asked about a name for the anti-pattern so I could research it further on my own. I'm surprised this particular bad coding practice doesn't seem to have a "canonical" name for it.

  Read the article

• Gnome-shell fails to load on 12.10

  - by Githlar

  I'm usually the one answering questions, but in this I'm throughly stumped! My Setup: Ubuntu 12.10 (Dist upgrade form 12.04) ATI M96 [Mobility Radeon HD 4650] Upon the first installation of 12.10 I had all kinds of issues getting the Legacy ATI drivers to install (I guess the source for the drivers isn't kosher with kernel 3.5). So, I added the repository ppa:makson96/fglrx - which has a version of the ATI source patched to work with kernel 3.5. After installation of fglrx-legacy from that PPA, gnome-shell and all my graphics work fine... until today. The Problem I unsuspended my computer today and the screen was black (not off, the black from the gnome lock screen). I'd move my mouse/hit a key and the background would flash and then it'd go back to black. Restarted via VT1 Logged into Gnome (gnome-shell) session, but no gnome-shell! Investigation: First, I went to VT1 and tried export DISPLAY=:0;gnome-shell --replace. It appeared to work fine, switch back to X and nothing. Went back to VT1 and saw this error message: JS ERROR: !!! Exception was: TypeError: Object 0x7fc748129c30 is not a subclass of (null), it's a xO JS ERROR: !!! message = '"Object 0x7fc748129c30 is not a subclass of (null), it's a xO"' JS ERROR: !!! fileName = '"/usr/share/gnome-shell/js/ui/tweener.js"' JS ERROR: !!! lineNumber = '218' JS ERROR: !!! stack = '"()@/usr/share/gnome-shell/js/ui/tweener.js:218 wrapper()@/usr/share/gjs-1.0/lang.js:204 ()@/usr/share/gjs-1.0/lang.js:145 ()@/usr/share/gjs-1.0/lang.js:239 init()@/usr/share/gnome-shell/js/ui/tweener.js:49 init()@/usr/share/gnome-shell/js/ui/environment.js:96 @<main>:1 "' Window manager warning: Log level 32: Execution of main.js threw exception: TypeError: Object 0x7fc748129c30 is not a subclass of (null), it's a xO Note: Everywhere it says "it's a xO", xO is actually garbled and changes every time (I'm thinking memory corruption?) This error is thrown by line 96 of /usr/share/gnome-shell/js/ui/environment.js: tweener.Init() Did a purge of fglrx-legacy, reboot, reinstall fglrx-legacy, reboot... same thing. Did a ppa-purge of ppa:gnome3-team/gnome3, and reinstalled gnome-shell and ubuntu-desktop from the standard repositores... same thing. I'm really at a loss here. I love gnome-shell and after using it for nearly a year now gnome classic just seems so archaic. Additional Information Apt log from the day I first suspended my machine (these are upgrades from the gnome3-team/gnome3 ppa and ubuntu-wine/ppa ppa): Start-Date: 2012-11-24 17:30:28 Commandline: aptdaemon role='role-commit-packages' sender=':1.618' Install: gkbd-capplet:amd64 (3.6.0-0ubuntu1), gnome-control-center-unity:amd64 (1.0-0ubuntu1~ubuntu12.10.1) Upgrade: nautilus:amd64 (3.6.2-0ubuntu0.1~quantal1, 3.6.3-0ubuntu2~ubuntu12.10.1), libgnome-control-center1:amd64 (3.4.2-0ubuntu19, 3.6.3-0ubuntu6~ubuntu12.10.1), wine1.5-i386:i386 (1.5.17-0ubuntu4, 1.5.18-0ubuntu1), wine1.5:amd64 (1.5.17-0ubuntu4, 1.5.18-0ubuntu1), gnome-settings-daemon:amd64 (3.4.2-0ubuntu14, 3.6.3-0ubuntu1~ubuntu12.10.1), gnome-control-center-data:amd64 (3.4.2-0ubuntu19, 3.6.3-0ubuntu6~ubuntu12.10.1), gnome-accessibility-themes:amd64 (3.6.0.2-0ubuntu1, 3.6.2-0ubuntu2~ubuntu12.10.1), gnome-themes-standard:amd64 (3.6.0.2-0ubuntu1, 3.6.2-0ubuntu2~ubuntu12.10.1), wine1.5-amd64:amd64 (1.5.17-0ubuntu4, 1.5.18-0ubuntu1), nautilus-data:amd64 (3.6.2-0ubuntu0.1~quantal1, 3.6.3-0ubuntu2~ubuntu12.10.1), gnome-control-center:amd64 (3.4.2-0ubuntu19, 3.6.3-0ubuntu6~ubuntu12.10.1), libnautilus-extension1a:amd64 (3.6.2-0ubuntu0.1~quantal1, 3.6.3-0ubuntu2~ubuntu12.10.1) End-Date: 2012-11-24 17:31:32 fglrxinfo (driver appears to be working): display: :0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: ATI Mobility Radeon HD 4650 OpenGL version string: 3.3.11653 Compatibility Profile Context Does anybody have any further ideas?

  Read the article

• Does *every* project benefit from written specifications?

  - by nikie

  I know this is holy war territory, so please read the question to the end before answering. There are many cases where written specifications make a lot of sense. For example, if you're a contractor and you want to get paid, you need written specs. If you're working in a team with 20 persons, you need written specs. If you're writing a programming language compiler or interpreter (and it's not perl), you'll usually write a formal specification. I don't doubt that there are many more cases where written specifications are a really good idea. I just think that there are cases where there's so little benefit in written specs, that it doesn't outweigh the costs of writing and maintaining them. EDIT: The close votes say that "it is difficult to say what is asked here", so let me clarify: The usefulness of written, detailed specifications is often claimed like a dogma. (If you want examples, look at the comments.) But I don't see the use of them for the kind of development I'm doing. So what is asked here is: How would written specifications help me? Background information: I work for a small company that's developing vertical market software. If our product is easier to use and has better performance than the competition, it sells. If it's harder to use, even if it behaves 100% as the specification says, it doesn't sell. So there are no "external forces" for having written specs. The advantage would have to be somewhere in the development process. Now, I can see how frozen specifications would make a developer's life easier. But we'll never have frozen specs. If we see in the middle of development that feature X is not intuitive to use the way it's specified, then we can only choose between changing the specification or developing a product that won't sell. You'll probably ask by now: How do you know when you're done? Well, we're continually improving our product. The competition does the same. So (hopefully) we're never done. We keep improving the software, and when we reach a point when the benefits of the improvements we've added since the last release outweigh the costs of an update, we create a new release that is then tested, localized, documented and deployed. This also means that there's rarely any schedule pressure. Nobody has to do overtime to make a deadline. If the feature isn't done by the time we want to release the next version, it'll simply go into the next version. The next question might be: How do your developers know what they're supposed to implement? The answer is: They have a lot of domain knowledge. They know the customers business well enough, so a high-level description of the feature (or even just the problem that the customer needs solved) is enough to implement it. If it's not clear, the developer creates a few fake screens to get feedback from marketing/management or customers, but this is nowhere near the level of detail of actual specifications. This might be inefficient for larger teams, but for a small team with low turnover it works quite well. It has the additional benefit that the developer in question often comes up with a better solution than the person writing the specs might have. This question is already getting very long, but let me address one last point: Testing. Like I said in the beginning, if our software behaves 100% like the spec says, it still can be crap. In fact, if it's so unintuitive that you need a spec to know how to test it, it probably is crap. It makes sense to have fixed, written tests for some core functionality and for regression bugs, but again, this is nowhere near a full written spec of how the software should behave when. The main test is: hand the software to a user who doesn't know it yet and tell him to use the new feature X. If she can figure out how to use it and it works, it works.

  Read the article

• When will EBS 12.2 be released?

  - by Steven Chan (Oracle Development)

  The most frequently asked question at OpenWorld this year was, "When will EBS 12.2 be released?" Sadly, Oracle's communication policies prohibit us from speculating about release dates for unreleased software. We are not permitted to give estimates, rough timelines, guesses, or anything else that remotely resembles specific guidance on release dates. You can monitor My Oracle Support and this blog for updates on EBS 12.2.  I'll post them here as soon as they're available.  I'm embedding an old favourite from 2007 in its entirety here, since it applies equally to new releases as well as certifications. "Loose Lips Sink Ships" (March 20, 2007)If I were to sort emails in my inbox into groups, the biggest -- by far -- would be the one for emails that start with, "When will _____ be certified with the E-Business Suite?"  I answer these dutifully but know that my replies can sometimes be maddening, for two reasons:  technical uncertainty, and Oracle's rules for such communications. On the Spiral Model of CertificationsTechnology stack certifications tend to be highly iterative in nature.  As a result, statements about certification dates tend to be accurate only when made in hindsight.  Laypeople are horrified to hear this, but it's the ugly truth.  Uncertainty is simply inherent to the process.  I've become inured to it over the years, but it might come as a surprise to you that it can take many cycles to get fully-released software to work together.  Take this scenario: We test a particular combination of Component A and B. If we encounter a problem, say, with Component A, we log a bug. We receive a new version of Component A. The process iterates again. The reality is this: until a certification is completed and released, there's no accurate way of telling how many iterations are yet to come.  This is true regardless of the number of iterations that have already been completed.  Our Lips Are SealedGenerally, people understand that things are subject to change, so the second reason I can't say anything specific is actually much more important than the first.  "Loose lips might sink ships" was coined in World War II in an effort to remind people that careless talk can have serious consequences.  Curiously, this applies to Oracle's communications about upcoming features, configurations, and releases, too.  As a publicly traded company, we have very strict policies that prohibit us from linking specific releases to specific dates.  If you've ever listened to an earnings call with analysts, you'll often hear them asking, "Can you add a little more color to that statement?"  For certifications, color is usually the only thing that I have.  Sometimes I can provide a bit more information about the technical nature of the certification in question, such as expected footprints or version levels.  I can occasionally share technical issues that we've found, too, to convey the degree of risk or complexity involved in the certification.  Aside from that, there's little additional information about specific dates, date ranges, or even speculation about dates that I can provide... that is, without having one of those uncomfortable conversations with Oracle Legal.  So, as much as it pains me to do so, when it comes to dates, I'm always forced to conclude with a generic reply that blandly states one of the following: We're working on that certification right now That certification is in the pipeline but hasn't been started yet We don't have plans for that certification Don't Shoot the MessengerThankfully, I've developed a thick skin over the years -- which is a good thing, considering the colorful and energetic responses I've received over the years after answering these questions.  However, on behalf of my Oracle colleagues who are faced with these questions every day in the field, I urge you to remember that they're required to follow these same corporate rules about date disclosures.  It never hurts to ask, but don't be too disappointed if we can't provide you with a detailed answer.  The Go-Go's had it right, after all.  Related Articles Webcast Replay Available: Technical Preview of EBS 12.2 Online Patching

  Read the article

• Gnome Install Error (1)

  - by Guy1984

  I'm trying to install Gnome on my Ubuntu 12.04 P.Pangolin and getting the following errors: root@***:~# sudo apt-get install gnome-core gnome-session-fallback Reading package lists... Done Building dependency tree Reading state information... Done gnome-core is already the newest version. gnome-session-fallback is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 4 not upgraded. 5 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up bluez (4.98-2ubuntu7) ... start: Job failed to start invoke-rc.d: initscript bluetooth, action "start" failed. dpkg: error processing bluez (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of gnome-bluetooth: gnome-bluetooth depends on bluez (>= 4.36); however: Package bluez is not configured yet. dpkg: error processing gnome-bluetooth (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-shell: gnome-shell depends on gnome-bluetooth (>= 3.0.0); however: Package gnome-bluetooth is not configured yet. dpkg: error processing gnome-shell (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-user-share: gnome-user-share depends on gnome-bluetooth; however: Package gnome-bluetooth is not configured yet. dpkg: error processing gnome-user-share (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-core: gnome-core depends on gNo apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already nome-bluetooth (>= 3.0); however: Package gnome-bluetooth is not configured yet. gnome-core depends on gnome-shell (>= 3.0); however: Package gnome-shell is not configured yet. gnome-core depends on gnome-user-share (>= 3.0); however: Package gnome-user-share is not configured yet. dpkg: error processing gnome-core (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: bluez gnome-bluetooth gnome-shell gnome-user-share gnome-core E: Sub-process /usr/bin/dpkg returned an error code (1) Syslog: Oct 5 16:04:17 ks34900 bluetoothd[5176]: Bluetooth daemon 4.98 Oct 5 16:04:17 ks34900 bluetoothd[5176]: Starting SDP server Oct 5 16:04:17 ks34900 bluetoothd[5176]: opening L2CAP socket: Address family not supported by protocol Oct 5 16:04:17 ks34900 bluetoothd[5176]: Server initialization failed Oct 5 16:04:17 ks34900 bluetoothd[5176]: Failed to init alert plugin Oct 5 16:04:17 ks34900 bluetoothd[5176]: Failed to init time plugin Oct 5 16:04:17 ks34900 bluetoothd[5176]: Failed to init proximity plugin Oct 5 16:04:17 ks34900 bluetoothd[5176]: Failed to open control socket: Address family not supported by protocol (97) Oct 5 16:04:17 ks34900 bluetoothd[5176]: Can't init bnep module Oct 5 16:04:17 ks34900 bluetoothd[5176]: Failed to init network plugin Oct 5 16:04:17 ks34900 bluetoothd[5176]: Unable to start SCO server socket Oct 5 16:04:17 ks34900 bluetoothd[5176]: Failed to init audio plugin Oct 5 16:04:17 ks34900 bluetoothd[5176]: Failed to init gatt_example plugin Oct 5 16:04:17 ks34900 bluetoothd[5176]: Can't open HCI socket: Address family not supported by protocol (97) Oct 5 16:04:17 ks34900 bluetoothd[5176]: adapter_ops_setup failed Oct 5 16:04:17 ks34900 kernel: init: bluetooth main process (5176) terminated with status 1 Oct 5 16:04:17 ks34900 kernel: init: bluetooth main process ended, respawning Oct 5 16:04:17 ks34900 bluez: Stopping uarts Oct 5 16:04:17 ks34900 bluez: Stopping rfcomm Any thoughts?

  Read the article

• How can I work efficiently on a desktop sharing workflow?

  - by OSdave

  I am a freelance Magento developer, based in Spain. One of my clients is a Germany based web development company and they're asking me something I think it's impossible. OK, maybe not impossible but definitely not a preferred way of doing things. One of their clients has a Magento Entreprise installation, which is the paid (and I think proprietary) version of Magento. Their client has forbidden them to download the files from his server. My client is asking me now to study one particular module of the application in order to interact with it from a custom module I'll have to develop. As they have a read-only ssh access to their client's server, they came up with this solution: Set up a desktop/screen sharing session between one of their developer's station and mine, alongsides with a skype conversation. Their idea is that I'll say to the developer: show me file foo.php The developer will then open this foo.php file in his IDE. I'll have then to ask him to show me the bar method, the parent class, etc... Remember that it's a read-only session, so forget about putting a Zend_Debug::log() anywhere, and don't even think about a xDebug breakpoint (they don't use any kind of debugger, sic). Their client has also forbidden them to use any version control system... My first reaction when they explained to me this was (and I actually did say it outloud to them): Well, find another client. but they took it as a joke from me. I understand that in a business point of view rejecting a client is not a good practice, but I think that the condition of this assignment make it impossible to complete. At least according to my workflow. I mean, the way I work or learn a new framework/program is: download all files and copy of db on my pc create a git repository and a branch run the application locally use breakpoints use Zend_Debug::log() write the code and tests commit to git repo upload to (test/staging first if there is one, production if not) server I have agreed to try the desktop sharing session, although I think it will be a waste of time. On one hand I don't mind, they pay me for that time, but I know me and I don't like the sensation of loosing my time. On the other hand, I have other clients for whom I can work according to my workflow. I am about to say to them that I cannot (don't want to) do it. Well, I'll first try this desktop sharing session: maybe I'm wrong and it can actually work. But I like to consider myself as a professional, and I know that I don't know everything. So I try to keep an open mind and I am always willing to learn new stuff. So my questions are: Can this desktop-sharing workflow work? What should be done in order to take the most of it? Taking into account all the obstacles (geographic locations, no local, no git), is there another way for me to work on that project?

  Read the article

• Memory is full with vertex buffer

  - by Christian Frantz

  I'm having a pretty strange problem that I didn't think I'd run into. I was able to store a 50x50 grid in one vertex buffer finally, in hopes of better performance. Before I had each cube have an individual vertex buffer and with 4 50x50 grids, this slowed down my game tremendously. But it still ran. With 4 50x50 grids with my new code, that's only 4 vertex buffers. With the 4 vertex buffers, I get a memory error. When I load the game with 1 grid, it takes forever to load and with my previous version, it started up right away. So I don't know if I'm storing chunks wrong or what but it stumped me -.- for (int x = 0; x < 50; x++) { for (int z = 0; z < 50; z++) { for (int y = 0; y <= map[x, z]; y++) { SetUpVertices(); SetUpIndices(); cubes.Add(new Cube(device, new Vector3(x, map[x, z] - y, z), grass)); } } } vertexBuffer = new VertexBuffer(device, typeof(VertexPositionTexture), vertices.Count(), BufferUsage.WriteOnly); vertexBuffer.SetData<VertexPositionTexture>(vertices.ToArray()); indexBuffer = new IndexBuffer(device, typeof(short), indices.Count(), BufferUsage.WriteOnly); indexBuffer.SetData(indices.ToArray()); Thats how theyre stored. The array I'm reading from is a byte array which defines the coordinates of my map. Now with my old version, I used the same loading from an array so that hasn't changed. The only difference is the one vertex buffer instead of 2500 for a 50x50 grid. cubes is just a normal list that holds all my cubes for the vertex buffer. Another thing that just came to mind would be my draw calls. If I'm setting an effect for each cube in my cube list, that's probably going to take a lot of memory. How can I avoid doing this? I need the foreach method to set my cubes to the right position foreach (Cube block in cube.cubes) { effect.VertexColorEnabled = false; effect.TextureEnabled = true; Matrix center = Matrix.CreateTranslation(new Vector3(-0.5f, -0.5f, -0.5f)); Matrix scale = Matrix.CreateScale(1f); Matrix translate = Matrix.CreateTranslation(block.cubePosition); effect.World = center * scale * translate; effect.View = cam.view; effect.Projection = cam.proj; effect.FogEnabled = false; effect.FogColor = Color.CornflowerBlue.ToVector3(); effect.FogStart = 1.0f; effect.FogEnd = 50.0f; cube.Draw(effect); noc++; }

  Read the article

• MySQL Server 5.6 default my.cnf and my.ini

  - by user12626240

  We've introduced a default my.cnf / my.ini file for MySQL Server that you can now see in the 5.6.8 release candidate: # For advice on how to change settings please see # http://dev.mysql.com/doc/refman/5.6/en/server-configuration-defaults.html [mysqld] # Remove leading # and set to the amount of RAM for the most important data # cache in MySQL. Start at 70% of total RAM for dedicated server, else 10%. # innodb_buffer_pool_size = 128M   # Remove leading # to turn on a very important data integrity option: logging # changes to the binary log between backups. # log_bin   # These are commonly set, remove the # and set as required. # basedir = ..... # datadir = ..... # port = ..... # socket = ..... # server_id = .....   # Remove leading # to set options mainly useful for reporting servers. # The server defaults are faster for transactions and fast SELECTs. # Adjust sizes as needed, experiment to find the optimal values. # join_buffer_size = 128M # sort_buffer_size = 2M # read_rnd_buffer_size = 2M   sql_mode=NO_ENGINE_SUBSTITUTION,STRICT_TRANS_TABLES    There is also a template file called my-default.cnf or my-default.ini that has these lines near the start: # *** DO NOT EDIT THIS FILE. It's a template which will be copied to the # *** default location during install, and will be replaced if you # *** upgrade to a newer version of MySQL.   On Linux systems, the mysql_install_db command will copy the template file to the final location, where the server will read and use the file, removing the extra three lines. On Windows, the installer will create extra settings based on the answers you gave during installation. Neither will overwrite an existing my.cnf or my.ini file. The only initially active setting here is to change the value of  sql_mode from the server default of NO_ENGINE_SUBSTITUTION to NO_ENGINE_SUBSTITUTION,STRICT_TRANS_TABLES. This strict mode changes warnings for some non-standard behaviour into errors. This can cause applications which rely on the non-standard things, like dates that aren't valid, to lose data. If we had just changed the server default, the new setting would affect all servers that lack an explicit sql_mode setting, including those where strict mode is harmful. So we did it in the default file instead because that will only affect new server installations. You should expect that in our next version after 5.6, the server default will include STRICT_TRANS_TABLES. Our Windows installer and some of our connectors already use STRICT_TRANS_TABLES by default. Strict has been our preferred setting for many years and it is good to see some development platforms are using it. If you need the old behaviour, just remove the STRICT_TRANS_TABLES setting. If you do this, please also ask your application provider to make it unnecessary. They can do that by setting the session sql_mode setting in their own connections, so the rest of the applications using the server don't have to have an undesirable default. We've kept this file as small as possible because we found that our old files were too big and confused people. We've also now removed the old my-huge and related example files. One key part of this is the link to the documentation, where we will provide an introduction to some key settings. We'd like to hear your feedback on settings that will benefit most users or are most important to call out for existing users. Please do that by commenting here or if you prefer by adding comments to this bug report.

  Read the article

• Asus X202e VivoBook, dual boot. How to get around UEFI and have Win8 & Ubuntu?

  - by Nukeface

  I've gotten my hands on an Asus Vivobook X202e. I like it, handy to use, small, etc etc. Oh, it's the i3 core version. For school I still need Windows * sigh * for the .NET development. (I know, possible in Ubuntu, this n that, but for ease atm wanting to keep it with Win8). So. How to install both on this little thing? I've found a way into the BIOS (before splash screen, mash F2. Works only after reboot, not cold boot). But the whole boot loading setup is different than from what I know, and I must've messed up something because it's been "Attempting Repairs", "Analyzing hard disk", and a bunch of other things for the past 15 minutes. (All I've done is selected "disabled" on secure boot, picky as ** Microsoft). Keeping the original Windows installation is of no concern. Found the product key already and have a clean install waiting. BTW, not trying to leech knowledge, even though first question and no answers. I'm more and more active on Stackoverflow. But, especially due to secure boot and windows 8, I'm going over to Ubuntu. Well, more and more anyway, I like my Windows based games as well ;) UPDATE Managed to do a clean install of Windows 8 Pro. After disabling Secure Boot, also had to disable fast boot, and enable Launch CSM, leaving the option which appeared (Launch PXE OpROM) disabled. Then I rebooted, with the USB Boot drive I created using the Windows 7 USB DVD Download Tool (scroll down for download link), provided by Microsoft. During the installation, I chose to install a clean version, therefor deleted the partitions containing current windows files. I left the Recovery partition (you never know...). Of course, the new Windows Installation dit not like this. Apparantly Windows cannot be installed on a GPT hard disk. Remember I hadn't changed the partition table, was still factory default! Minus a few partitions, granted. So deleted ALL partittions, did a format of the disk, created a new partition. Et voila, Windows installation started. FINALLY! WONDROUS After the installation, Windows still had background images located in C:/Users/ ME /AppData/Local/Microsoft/Themes/RoamedThemeFiles/DesktopBackground/ that I had in the previous installation. Before doing: format, delete partition, cascade partitions, create new partition of different size, format partition, install Windows. It managed to keep the images through all that. Anyone got an idea on that one? It also remembered the settings for the Windows Aero theme... UPDATED QUESTION: After all this you'd think I'd have the rest figured out. Wrong. Ubuntu 12.10, 64 bit installation can't read the partitioning of the hdd during the installation. Any ideas on how to fix this so the install for a dual-boot system can proceed? (Preferably without starting anew with Windows as well ;) )

  Read the article

• Cannot establish maximum resolution on ASUS PB278Q

  - by dentuzhik

  I've recently bought brand new ASUS PB278Q monitor. When trying to connect to my laptop, everything works great, except that I can't get the native resolution of my monitor (2560x1440) working. The automatic is 1920x1080. My graphic card is Nvidia GeForce 320m. Here's output from lspci for it: ~$ lspci | grep VGA 02:00.0 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 320M] (rev a2) and also xrandr: ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected primary 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 I have proprietary drivers installed on my machine, here's the info about the monitor from nvidia-settings (Actually I don't have enough reputation to post images, so here's the text): Chip Location: Internal Signal: TDMS Connection link: Single Native resolution: 2560x1440 Refresh rate: 60.00 Hz The monitor is connected to laptop via HDMI cable, and honestly I have no idea what version it is, and what version is my HDMI output of my graphics card. I tried to find how I can figure it out on the web, but had no luck. Also my video card has only VGA and HDMI outs so I can't test neither DVI-D cable nor DisplayPort. So apparently, there's some problem over there. At least I want to know exactly what's going on. I've tried to see if it a linux-specific problem, but windows also gave me the same resolution by default. What I've already tried: Connect through VGA (stupid one, of course it gave me 1920x1080). Checked two HDMI cables (not sure if they're the same or not, as mentioned above). Played around with xrandr and adding custom modes. Didn't help. Surfed for the info a lot on the web, but couldn't get appropriate results. Actually xrandr gives me the following: ~$ cvt 2560 1440 60 # 2560x1440 59.96 Hz (CVT 3.69M9) hsync: 89.52 kHz; pclk: 312.25 MHz Modeline "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr --newmode "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected primary 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 2560x1440_60.00 (0x34f) 312.2MHz h: width 2560 start 2752 end 3024 total 3488 skew 0 clock 89.5KHz v: height 1440 start 1443 end 1448 total 1493 clock 60.0Hz ~$ xrandr --addmode HDMI-0 2560x1440_60.00 X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 29 Current serial number in output stream: 30 What I intend to do next: Try another HDMI cable? Try HDMI to DVI-D cable? Try HDMI to DisplayPort cable? Another type of adapters? VGA to DVI-D? Buy another laptop with another graphic card. Damn. My ideas pretty much end here. Any ideas? Any explanations why it isn't working are appreciated.

  Read the article

• Rethinking Oracle Optimizer Statistics for P6 Part 2

  - by Brian Diehl

  In the previous post (Part 1), I tried to draw some key insights about the relationship between P6 and Oracle Optimizer Statistics.  The first is that average cardinality has the greatest impact on query optimization and that the particular queries generated by P6 are more likely to use this average during calculations. The second is that these are statistics that are unlikely to change greatly over the life of the application. Ultimately, our goal is to get the best query optimization possible.  Or is it? Stability No application administrator wants to get the call at 9am that their application users cannot get there work done because everything is running slow. This is a possibility with a regularly scheduled nightly collection of statistics. It may not just be slow performance, but a complete loss of service because one or more queries are optimized poorly. Ideally, this should not be the case. The database optimizer should make better decisions with more up-to-date data. Better statistics may give incremental performance benefit. However, this benefit must be balanced against the potential cost of system down time.  It is stability that we ultimately desire and not absolute optimal performance. We do want the benefit from more accurate statistics and better query plans, but not at the risk of an unusable system. As a result, I've developed the following methodology around managing database statistics for the P6 database.  1. No Automatic Re-Gathering - The daily, weekly, or other interval of statistic gathering is unlikely to be beneficial. Quite the opposite. It is more likely to cause problems. 2. Smart Re-Gathering - The time to collect statistics is when things have changed significantly. For a new installation of P6, this is happening more often because the data is growing from a few rows to thousands and more. But for a mature system, the data is not changing significantly from week-to-week. There are times to collect statistics: New releases of the application Changes in the underlying hardware or software versions (ex. new Oracle RDBMS version) When additional user groups are added. The new groups may use the software in significantly different ways. After significant changes in the data. This may be monthly, quarterly or yearly.  3. Always Test - If you take away one thing from this post, it would be to always have a plan to test after changing statistics. In reality, statistics can be collected as often as you desire provided there are tests in place to verify that performance is the same or better. These might be automated tests or simply a manual script of application functions. 4. Have a Way Out - Never change the statistics without a way to return to the previous set. Think of the statistics as one part of the overall application code that also includes the source code--both application and RDBMS. It would be foolish to change to the new code without a way to get back to the previous version. In the final post, I will talk about the actual script I created for P6 PMDB and possible future direction for managing query performance. 

  Read the article

• Multiple Zend application code organisation

  - by user966936

  For the past year I have been working on a series of applications all based on the Zend framework and centered on a complex business logic that all applications must have access to even if they don't use all (easier than having multiple library folders for each application as they are all linked together with a common center). Without going into much detail about what the project is specifically about, I am looking for some input (as I am working on the project alone) on how I have "grouped" my code. I have tried to split it all up in such a way that it removes dependencies as much as possible. I'm trying to keep it as decoupled as I logically can, so in 12 months time when my time is up anyone else coming in can have no problem extending on what I have produced. Example structure: applicationStorage\ (contains all applications and associated data) applicationStorage\Applications\ (contains the applications themselves) applicationStorage\Applications\external\ (application grouping folder) (contains all external customer access applications) applicationStorage\Applications\external\site\ (main external customer access application) applicationStorage\Applications\external\site\Modules\ applicationStorage\Applications\external\site\Config\ applicationStorage\Applications\external\site\Layouts\ applicationStorage\Applications\external\site\ZendExtended\ (contains extended Zend classes specific to this application example: ZendExtended_Controller_Action extends zend_controller_Action ) applicationStorage\Applications\external\mobile\ (mobile external customer access application different workflow limited capabilities compared to full site version) applicationStorage\Applications\internal\ (application grouping folder) (contains all internal company applications) applicationStorage\Applications\internal\site\ (main internal application) applicationStorage\Applications\internal\mobile\ (mobile access has different flow and limited abilities compared to main site version) applicationStorage\Tests\ (contains PHP unit tests) applicationStorage\Library\ applicationStorage\Library\Service\ (contains all business logic, services and servicelocator; these are completely decoupled from Zend framework and rely on models' interfaces) applicationStorage\Library\Zend\ (Zend framework) applicationStorage\Library\Models\ (doesn't know services but is linked to Zend framework for DB operations; contains model interfaces and model datamappers for all business objects; examples include Iorder/IorderMapper, Iworksheet/IWorksheetMapper, Icustomer/IcustomerMapper) (Note: the Modules, Config, Layouts and ZendExtended folders are duplicated in each application folder; but i have omitted them as they are not required for my purposes.) For the library this contains all "universal" code. The Zend framework is at the heart of all applications, but I wanted my business logic to be Zend-framework-independent. All model and mapper interfaces have no public references to Zend_Db but actually wrap around it in private. So my hope is that in the future I will be able to rewrite the mappers and dbtables (containing a Models_DbTable_Abstract that extends Zend_Db_Table_Abstract) in order to decouple my business logic from the Zend framework if I want to move my business logic (services) to a non-Zend framework environment (maybe some other PHP framework). Using a serviceLocator and registering the required services within the bootstrap of each application, I can use different versions of the same service depending on the request and which application is being accessed. Example: all external applications will have a service_auth_External implementing service_auth_Interface registered. Same with internal aplications with Service_Auth_Internal implementing service_auth_Interface Service_Locator::getService('Auth'). I'm concerned I may be missing some possible problems with this. One I'm half-thinking about is a config.ini file for all externals, then a separate application config.ini overriding or adding to the global external config.ini. If anyone has any suggestions I would be greatly appreciative. I have used contextswitching for AJAX functions within the individual applications, but there is a big chance both external and internal will get web services created for them. Again, these will be separated due to authorization and different available services. \applicationstorage\Applications\internal\webservice \applicationstorage\Applications\external\webservice

  Read the article

• Disabling the right-click sub menu using JQuery

  - by nikolaosk

  Recently I needed to disable the right-click contextual menu in an HTML page for a very simple HTML application I was creating for a friend.This is going to be a short post where I will demonstrate how to disable the right-click contextual menu.I will use the very popular JQuery Library. Please download the library (minified version) from http://jquery.com/downloadPlease find here all my posts regarding JQuery.In this hands-on example I will be using Expression Web 4.0.This application is not a free application. You can use any HTML editor you like.You can use Visual Studio 2012 Express edition. You can download it here. I am going to create a very simple HTML 5 page with some text and an image. The HTML markup for the page follows. <!DOCTYPE html><html lang="en">  <head>    <title>HTML 5, CSS3 and JQuery</title>        <meta http-equiv="Content-Type" content="text/html;charset=utf-8" >    <link rel="stylesheet" type="text/css" href="style.css">     <script type="text/javascript" src="jquery-1.8.2.min.js">        </script><script type="text/javascript"> (function ($) { $(document).bind('contextmenu', function () { return false;}); })(jQuery); </script>       </head>  <body>      <div id="header">      <h1>Learn cutting edge technologies</h1>      <h2>HTML 5, JQuery, CSS3</h2>    </div>      <figure>  <img src="html5.png" alt="HTML 5"></figure>        <div id="main">          <h2>HTML 5</h2>                        <article>          <p>            HTML5 is the latest version of HTML and XHTML. The HTML standard defines a single language that can be written in HTML and XML. It attempts to solve issues found in previous iterations of HTML and addresses the needs of Web Applications, an area previously not adequately covered by HTML.          </p>          </article>      </div>             </body>  </html> This is the JQuery code, I use (function ($) { $(document).bind('contextmenu', function () { return false;}); })(jQuery); I simply disable/cancel the contextmenu event.When I load the simple page on the browser and I right-click the context menu does not appear.Hope it helps!!!

  Read the article

< Previous Page | 435 436 437 438 439 440 441 442 443 444 445 446  | Next Page >