Search Results

Search found 2064 results on 83 pages for '802 11g'.

Page 44/83 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• Laptop is super slow on network

  - by Gary

  So on our network we have a bunch of wireless macs and window Operating laptops, we have a network setup with 802.11g,b,n. All the laptops seem fine except one which is only getting speeds of 54Mb. I have changed the encryption from AES to TKIP and reset the connection, i have updated the drivers, tried plugging it into the LAN and still same slow speed. Apparently the laptop with the slow speed is fine on other networks. I don't know what to do, can anyone help me?

  Read the article

• My wireless has suddenly became disabled by hardware switch, BIOS, rfkill, fn+f8 do nothing

  - by cwwk

  I have a toshiba l655d-s5145. There is no physical toggle for the wireless, although the f8 key is supposed to do the trick. It doesn't. The wireless has been working since October, and suddenly, nothing. RFKILL reports that the wireless is hard blocked, but unblock wifi, unblock 0, unblock all do nothing. I inserted a usb dongle, and that is also disabled by hardware switch, although rfkill reports that it is neither hard nor soft blocked. My onboard wireless is 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) according to lspci. Lsmod reports that these drivers are loaded. rtl8192c_common 75767 1 rtl8192ce rtlwifi 110972 1 rtl8192ce I resorted to reformatting the drive and reinstalling, but that also did not work. In BIOS I restored system defaults as there is no specific entry for wifi. Before reinstalling a pure xubuntu I went into Unity and saw that the airplane mode was on and despite being toggled off, it returned to the on position. I'm not sure where to find airplane mode in Xubuntu. What else can I do? I need my wireless.

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• Broadcom Wireless Issues in Lubuntu 14.04

  - by ratxinxaxcage67

  I recently installed Lubuntu 14.04 on my parents' old laptop, and I've been having a super difficult time getting the Broadcom card up and running. I've been following this thread: Installing Broadcom Wireless Drivers ...but I'm still stuck. lspci -vnn | grep Network showed: 06:05.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 02) iwconfig showed: lo no wireless extensions. eth0 no wireless extensions. I've installed b43-firmware-installer and b43-fwcutter and also the linux-firmware-nonfree package. At boot, I keep getting a b43-phy0 error, so I tried sudo rmmod b43, and I got: rmmod: ERROR: Module b43 is not currently loaded I also tried: dmesg | grep b43 [ 17.318405] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4) [ 17.384870] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw [ 18.046777] b43legacy ssb0:0: Direct firmware load failed with error -2 [ 18.046785] b43legacy ssb0:0: Falling back to user helper [ 18.047858] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed. [ 18.047965] b43legacy-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3). I went to url it told me to, but it didn't tell me to do anything I haven't already tried. Any help and/or suggestions would be greatly appreciated!

  Read the article

• Is the BCM4306 wireless card ipv6 capable?

  - by horroricane

  I've been trying to connect with ipv6 enabled networks with my Broadcom Wireless card under Ubuntu 12.04. The wireless card model is BCM4306. $lspci $Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03) $Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) I have been unsuccesful to connect through an ipv6 address, but I can still connect to a network when assigned an ipv4 address. While searching for an answer or a solution, I know the kernel can handle dealing with ipv6. So, what's left to question should be the hardware handling the connection. Unfortunately nothing comes up when I specifically try to search for information on BCM4306 ipv6 capabilities. I just tried using a wired connection to establish an ipv6 only connection to the network I'm on right now, but I got the same behavior of constant disconnections. Maybe it's not the hardware? I don't know.. I don't want to disable ipv6 on my machine as relevant networks I'll be connecting to will be using it exclusively, but I'm not sure what is wrong and which parts should I replace/fix to get this working.. Could someone please point me in a fruitful direction to get ipv6 working under Ubuntu 12.04?

  Read the article

• 12.10 Wireless networking

  - by user108594

  I downloaded ubuntu 12.10 using WUBI and cannot connect to the internet. I removed it and downloaded ubuntu 12.04 still cannot connect. This I assume rules out the program being the problem. I reinstalled 12.10. When loaded I get the same message W/red (x) stating Internet not connected. I went to the Settings drop down box and it does not reveal the network list but (enable networking has a ck mark). Am running a HP Laptop with a w/7/64 OS that has a kill switch that indicates (orangeno connection) I downloaded 12.10 on my desktop (on the same network) and everything OK. I tried to follow the instructions in the help menu but got lost and confused . Sincerely Dan Additional Info per request Broadcom 802.11b/g Wlan Internal pc [hp laptop] P.S. I've been out of town for about a month. TKS for your gitback I did install 12.10 via cd and everything ok,but retried alongside 7 and unable to connect to internet,also took laptop and hard wired using ethernet cable and everything ok. stumped again and running out of ideas!!!

  Read the article

• Wireless connection disconnects and reconnects with a Netgear WNA1000

  - by William Berkenkamp

  Ever since I made the permanent switch from Vista to Ubuntu i've had wireless connectivity problems. From watching the network manager when it disconnects it seems like it turns off the receiver for some reason. Could it be bad drivers? I used their install software and the site doesn't really offer driver downloads. The adapter is a Netgear WNA1000 if memory serves, and I don't know much about the router except that it's a Motorola Surfboard. And I figure this might help a bit *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: 00:1b:b9:a7:39:a4 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:d800(size=256) memory:feaff000-feafffff memory:feac0000-feadffff *-network description: Wireless interface physical id: 1 bus info: usb@2:1.1 logical name: wlan0 serial: 00:26:f2:8b:fb:38 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.2.0-24-generic-pae firmware=1.9.4 ip=10.0.0.36 link=yes multicast=yes wireless=IEEE 802.11bgn I have tried installing WICD and it didn't fix the problem. Any help would be greatly appreciated. This problem is greatly limiting what I can do with my computer.

  Read the article

• Driver for asus wireless PC card WL-100GE

  - by emab

  I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• cannot boot ubuntu 13.10 with my usb, Can i change the kernal on my laptop to run it?

  - by Carlos Dunick

  Currently i am running 12.04 and looking for an upgrade to 13.10 I first tried a bootable 64bit usb and failed. With the message saying "Kernal requires an x86-64 CPU but only detected an I686 CPU Unable to boot please use a kernal appropriate for your CPU" then tried 32bit and same message came up. Is this due to my laptop simply being to slow? or can/should i change the kernal somehow? Acer Aspire 5710z Intel Pentium dual core processor, 1.73Ghz, 533 MHz FSB, 1 MB L2 cache. 2GB DDR2 lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) 00:1c.2 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02) 04:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02) 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 06:00.0 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller 06:00.1 SD Host controller: ENE Technology Inc ENE PCI SmartMedia / xD Card Reader Controller 06:00.2 FLASH memory: ENE Technology Inc Memory Stick Card Reader Controller 06:00.3 FLASH memory: ENE Technology Inc ENE PCI Secure Digital / MMC Card Reader Controller

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• Wifi doesn't connect if I'm upstairs

  - by user11233

  Hello there, I'm finding that Wifi connects when I'm in the living room, where the internet router etc is. But if I try to connect upstairs it is a no go. Booting in Windows 7 (dual boot :D ) I find that Wifi connects. I find this very confusing and have it since the install. Please help! Kind regards. #sudo lshw -c network *-network description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 00:21:5d:1a:63:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=2.6.35-26-generic firmware=8.24.2.12 ip=10.0.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11abg resources: irq:49 memory:de200000-de201fff Hope it helps! Hello guys, just tried to connect internet upstairs and to my surprise it does connect. Don't know exactly why. Only thing I've done recently is input the codes said bij Oli. Two things I've done on my own 1: installed Jupiter and 2: installed laptop-mode-tools. I really don't know if this can effect my internet but it's the only thing I can think of. Thanks for all the help, really appreciate it :) PS If someone thinks it might be helpful for others I would like to help find a 'real' solution to this problem. Just post down what I need to post here and I will try my best to help.

  Read the article

• ubuntu 11.10 can't find wireless after waking from sleep

  - by Colleen

  I've tried a lot of proposed solutions, most of them adding files to /etc/pm/config.d, as well as WiFi stops working after waking from suspend and nothing has worked. hardware info: [colleen@colleen-HP ~]$ sudo lshw -C network [sudo] password for colleen: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:b1:ea:67 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:4000(size=256) memory:c1404000-c1404fff memory:c1400000-c1403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 8c:a9:82:99:48:8c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-21-generic-pae firmware=39.31.5.1 build 35138 ip=192.168.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:c5500000-c5501fff Is anyone else still having this problem? The two solutions I haven't tried are installing wicd and upgrading because I've heard both are kind of unstable/buggy and wicd frankly scares me.

  Read the article

• Wifi interface changes name seemingly at random

  - by ray_voelker

  I'm currently having some issues getting a wireless interface to work continuously under an install of Ubuntu 12.04.1 LTS. Some of the issues I'm experiencing include Connection will drop out after some time after it has initially worked. Interface will be a different name after a reboot. For example, wlan0 will become wlan4 when using the ifconfig -a command. Ubuntu will take a long time to boot, looking for network adapters. The purpose of this build is to function as a web kiosk in a library. The computer is supposed to boot up into a web browser, and allow for browsing of the catalog. For some reason this interface does not appear to be working as it should. Are there any explanations for some of these problems I'm having, and perhaps some solutions? The wireless card appears as this after doing an lspci ... Ralink corp. RT2561/RT61 802.11g PCI In the /etc/network/interfaces file I have the following configuration for the interface. auto wlan0 iface wlan0 inet dhcp wireless-essid UDwireless wireless-mode Managed Thanks in advance for help on this.

  Read the article

• Vlan Tagging at Access Port in Switch

  - by singh

  I'm Confused from the fact that Vlan tagging is done at access port and trunk port always gets tagged packets (until its case of native vlan).But I still believe in other fact which says tagging happen only when a frame hit the trunk port which means trunk port gets untagged frame and tagging is not possible at access port. Would like to know where actually this tagging happens ? and also which command we can use to encapsulate 802.1q protocol to access port ? The way we do at trunk port is switchport trunk encapsulation dot1q Is the above command applicable for access mode also?

  Read the article

• How do I know if I need a layer 3 switch?

  - by eekmeter

  We currently have a flat network with a bunch of unmanaged switches. I would like to use VLANs to segregate certain users like guests and I would like to use 802.1x. However, I'm not sure if what I need is a layer 3 or a level 2 switch. From what I understand a layer 3 switch does routing between VLANs. I don't think I need this at the moment but as I said I'm not sure since this is all new to me. What else would a layer 3 switch do for me? Our network is relatively small, less than a 100 users. What exactly does a layer 3 switch do that I can't get with a layer 2 switch? When would I need a layer 3?

  Read the article

• Blacklist a single access point of a wireless network

  - by Zr40

  At my university, one of the wireless access points is failing. When something tries to associate to the network using that access point, it deassociates the client, claiming 802.1X authentication failure. Other access points do work normally using the same credentials. The issue has been reported, but after a month it still has still not been fixed. Now, I'm looking for a way to blacklist the access point's BSSID, so the OS prefers other access points on the same SSID. How can I blacklist specific BSSIDs in either Mac OS X Snow Leopard or Windows 7?

  Read the article

• How do I know if I need a level 3 switch?

  - by eekmeter

  We currently have a flat network with a bunch of unmanaged switches. I would like to use VLANs to segregate certain users like guests and I would like to use 802.1x. However, I'm not sure if what I need is a level 3 or a level 2 switch. From what I understand a level 3 switch does routing between VLANs. I don't think I need this at the moment but as I said I'm not sure since this is all new to me. What else would a level 3 switch do for me? Our network is relatively small, less than a 100 users. What exactly does a level 3 switch do that I can't get with a level 2 switch? When would I need a level 3?

  Read the article

• Is 50% download speed on a wireless G network normal?

  - by Bartlomiej Skwira

  I have a wired connection of about 36Mb/s, but my wireless speed is max at about 18-19Mb/s. I have a WRT54G-TM (T-Mobile, 802.11G) router with DD-WRT firmware - I've upgraded it to latest build. Done some settings changes: changed channel - 13 wireless network mode - G-only ACK Timing - 0 Fragmentation Threshold and RTS Threshold - 2304 Basic Rate - All Signal/Noise ratio: -46/-94, signal quality ~50-60%. Is this normal with G networks? Edit: The AP is located about 2 meters from laptop, no walls or metal objects, but its next to a TV. I've done a channel scan (had problems locating it, go to "Status - Wireless - Site survey" - lame naming) and everybody else is on channels 1 and 6. Switched to channel 11 but it didn't help. As for trasmit power I got best results with default 71mw. The antenna might be a factor, I'm using the default 2 antennas.

  Read the article

• Windows 7/8 can't connect to an N Router

  - by xenoterracide

  I have a router running OpenWRT backfire, with N and A/B/G being broadcast. A linux laptop, and a Mac laptop can see the N network and connect to it (or at least they could last weekend). But there is now a Windows 7 Desktop with a B/G/N wireless card, and a Windows 8 Laptop with a B/G/N wireless card that can't see the N network only the B/G broadcast. The B/G and N have different SSID's and Encryption ( WEP and WPA2 PSK respectively ). The N SSID isn't even visible. Does anyone have any suggestions as to how to troubleshoot further? Or what might be the cause? update wireless info Desktop Dell Wireless 1502 802.11b/g/n Atheros Communications Inc 9.2.0.412

  Read the article

• Switch to switch encryption over a wireless bridge (TrustSec?)

  - by metatheorem

  I am planning to connect an existing Cisco 3750 switch to a 3560C switch over a wireless PTP bridge. The bridge will be WPA2 protected, but I am looking for an additional measure of security between the switches to prevent other wireless access through either switch. They do not support IPSec, only 802.1Q tunnels, and buying additional hardware is not likely an option. I am looking into using TrustSec manual mode between the switches. After some effort reading into TrustSec and MACsec, I am mostly certain this is a good choice over the wireless bridge, keeping in mind it is a shared medium. Two questions: Can I reliably prevent other wireless traffic from accessing the switches using TrustSec? Does anyone know of any better options with the 3000 series switches?

  Read the article

• list and explanations of ways to boost this router's signal strength? [closed]

  - by barlop

  Possible Duplicates: Improve Wireless Signal How to get wireless coverage over my whole house? What's the best way to increase the range of my 802.11g router? The back of my house doesn't have WiFi Signal I'm interested in ways that are both specific to certain routers, and generic. When I say generic, I don't necessarily mean a one way that works for many.. but it can also be a generic answer, so mentioning solutions for different situations. So not just the one router I mention. Explanations are important, as well as all the ways. One i'm particularly interested in boosting the strength of is this wireless router/modem Netgear VMDG280 maybe anywhere in a big house with three floors, maybe from the garden.

  Read the article

• How to remove AegisP.sys

  - by NinjaCat

  When I boot my laptop, I get the following event in the error log... I cannot tell which service is trying to use the aegisp.sys file or generating this event. Can anyone shed some light? Google is not very helpful with this issue ;) Event Type: Error Event Source: Service Control Manager Event Category: None Event ID: 7000 Date: 8/20/2010 Time: 10:50:03 PM User: N/A Computer: XXX Description: The AEGIS Protocol (IEEE 802.1x) v3.6.0.0 service failed to start due to the following error: The system cannot find the file specified. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• WIndows Hosted Network

  - by Nandakumar V

  I have created a hosted network in my windows7 system. The netsh wlan show hostednetwork command gives the output Hosted network settings ----------------------- Mode : Allowed SSID name : "rambo" Max number of clients : 100 Authentication : WPA2-Personal Cipher : CCMP Hosted network status --------------------- Status : Started BSSID : xx:xx:xx:xx:xx:xx Radio type : 802.11n Channel : 11 Number of clients : 1 xx:xx:xx:xx:xx:xx Authenticated But I have forgot the password for this connection and after some googling I found the command netsh wlan refresh hostednetwork YourNewNetworkPassword. But on executing this command it get the error C:\Users\user>netsh wlan refresh hostednetwork rambo123 Invalid value "rambo123" for command option "data". Usage: refresh hostednetwork [data=]key I have no idea what is wrong with this command.

  Read the article

• My wireless network slows down every 7.5 minutes when my desktop is switched on

  - by Dog Ears

  My network has lag spikes lasting for a few seconds every 7.5 mins. The spikes also effect any other computer connected connected to my wirless router at the time. My wife has to connect her laptop via a cable to prevent the lag causing problems when she's VPNing into her work. If I switch my PC off the problem goes away! I've got an Edimax 7728ln 802.11n wireless card and Speedtouch 585v7 (I'm with Be) I've Tried... Updated the drivers from Edimax website: 2.0.3.0 (it does say 3.0.2.0 in devices properties though) WLAN Optimizer doesn't seem to be helping What can I do?

  Read the article

• Can one use Airport (Time Capsule) with an external DHCP server?

  - by DNS

  I currently share my DSL connection using a wireless router with DHCP disabled, and dnsmasq running on a Mac Mini serving DHCP & DNS. This setup is important because I have clients doing PXE boot, and I need the control over DHCP that dnsmasq provides. There is also a Time Capsule on the network that's used purely as a backup device; its wireless functions are disabled. The wireless router is starting to get a little flaky, and since it doesn't support 802.11n I'd like to replace it. Rather than buying a new router, I'd like to just use the Time Capsule. But I see no way to disable its DHCP server; when I set the connection type to PPPoE, it insists on serving DHCP. Is there any way to use Airport PPPoE with a DHCP server elsewhere on the network?

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >