activate - Page 44 - Developer IT

Can only bring up one of two interfaces

- by mstaessen

I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

Read the article

What else can I do to secure my Linux server?

- by eric01

I want to put a web application on my Linux server: I will first explain to you what the web app will do and then I will tell you what I did so far to secure my brand new Linux system. The app will be a classified ads website (like gumtree.co.uk) where users can sell their items, upload images, send to and receive emails from the admin. It will use SSL for some pages. I will need SSH. So far, what I did to secure my stock Ubuntu (latest version) is the following: NOTE: I probably did some things that will prevent the application from doing all its tasks, so please let me know of that. My machine's sole purpose will be hosting the website. (I put numbers as bullet points so you can refer to them more easily) 1) Firewall I installed Uncomplicated Firewall. Deny IN & OUT by default Rules: Allow IN & OUT: HTTP, IMAP, POP3, SMTP, SSH, UDP port 53 (DNS), UDP port 123 (SNTP), SSL, port 443 (the ones I didn't allow were FTP, NFS, Samba, VNC, CUPS) When I install MySQL & Apache, I will open up Port 3306 IN & OUT. 2) Secure the partition in /etc/fstab, I added the following line at the end: tmpfs /dev/shm tmpfs defaults,rw 0 0 Then in console: mount -o remount /dev/shm 3) Secure the kernel In the file /etc/sysctl.conf, there are a few different filters to uncomment. I didn't know which one was relevant to web app hosting. Which one should I activate? They are the following: A) Turn on Source Address Verification in all interfaces to prevent spoofing attacks B) Uncomment the next line to enable packet forwarding for IPv4 C) Uncomment the next line to enable packet forwarding for IPv6 D) Do no accept ICMP redirects (we are not a router) E) Accept ICMP redirects only for gateways listed in our default gateway list F) Do not send ICMP redirects G) Do not accept IP source route packets (we are not a router) H) Log Martian Packets 4) Configure the passwd file Replace "sh" by "false" for all accounts except user account and root. I also did it for the account called sshd. I am not sure whether it will prevent SSH connection (which I want to use) or if it's something else. 5) Configure the shadow file In the console: passwd -l to lock all accounts except user account. 6) Install rkhunter and chkrootkit 7) Install Bum Disabled those services: "High performance mail server", "unreadable (kerneloops)","unreadable (speech-dispatcher)","Restores DNS" (should this one stay on?) 8) Install Apparmor_profiles 9) Install clamav & freshclam (antivirus and update) What did I do wrong and what should I do more to secure this Linux machine? Thanks a lot in advance

Read the article

How to install RAID drivers on already installed Windows 7?

- by happysencha

64-bit Windows 7 Ultimate 6GB RAM Intel i7 920 Intel X25-M SSD 80GB 2,5" Club 3D Radeon HD5750 GA-EX58-UD4P Motherboard I've been running fine with Windows 7 installed on the SSD. I wanted to create an mirrored Raid-1 setup for backups using two hard disks, so I ordered two Samsung HD203WI. This motherboard supports two different RAID controllers, the Intel's ICH10R and Gigabyte's SATA2 SATA controller. There are 6 SATA ports behind the ICH10R and 2 SATA ports for the Gigabyte controller. I googled around and seemed that the ICH10R is a better choice and since then I've been trying to make it work. When I activate the [RAID] mode from BIOS, the Windows 7 gives BSOD exactly as described by this guy: "Windows 7 will start to boot, it gets to the screen where there are 4 colors coming together and it blue screens and restarts no matter what I do." First thing I did: turned off the RAID and booted to Windows and tried to install the SATA RAID drivers from Gigabyte. I launch the driver installation program and it gives "This computer does not meet the minimum requirements for installing the software" error. I then tried Intel's Rapid Storage Technology drivers (which apparently is the same as the one offered at Gigabyte's site), but it resulted in exactly the same error. I then detached the new Samsung hard disks from the SATA ports, but left the [RAID] enabled in BIOS. To my surprise, it still BSOD'd, so at this point I knew it is an OS/driver issue. Also, I tried with the Gigabyte's RAID enabled (while the ICH10R RAID disabled) and it booted just fine. So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed." So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks. I mean why would I need to re-install operating system to add RAID setup?

Read the article

Pure Server-Side Filtering with RadGridView and WCF RIA Services

Those of you who are familiar with WCF RIA Services know that the DomainDataSource control provides a FilterDescriptors collection that enables you to filter data returned by the query on the server. We have been using this DomainDataSource feature in our RIA Services with DomainDataSource online example for almost an year now. In the example, we are listening for RadGridViews Filtering event in order to intercept any filtering that is performed on the client and translate it to something that the DomainDataSource will understand, in this case a System.Windows.Data.FilterDescriptor being added or removed from its FilterDescriptors collection. Think of RadGridView.FilterDescriptors as client-side filtering and of DomainDataSource.FilterDescriptors as server-side filtering. We no longer need the client-side one. With the introduction of the Custom Filtering Controls feature many new possibilities have opened. With these custom controls we no longer need to do any filtering on the client. I have prepared a very small project that demonstrates how to filter solely on the server by using a custom filtering control. As I have already mentioned filtering on the server is done through the FilterDescriptors collection of the DomainDataSource control. This collection holds instances of type System.Windows.Data.FilterDescriptor. The FilterDescriptor has three important properties: PropertyPath: Specifies the name of the property that we want to filter on (the left operand). Operator: Specifies the type of comparison to use when filtering. An instance of FilterOperator Enumeration. Value: The value to compare with (the right operand). An instance of the Parameter Class. By adding filters, you can specify that only entities which meet the condition in the filter are loaded from the domain context. In case you are not familiar with these concepts you might find Brad Abrams blog interesting. Now, our requirements are to create some kind of UI that will manipulate the DomainDataSource.FilterDescriptors collection. When it comes to collections, my first choice of course would be RadGridView. If you are not familiar with the Custom Filtering Controls concept I would strongly recommend getting acquainted with my step-by-step tutorial Custom Filtering with RadGridView for Silverlight and checking the online example out. I have created a simple custom filtering control that contains a RadGridView and several buttons. This control is aware of the DomainDataSource instance, since it is operating on its FilterDescriptors collection. In fact, the RadGridView that is inside it is bound to this collection. In order to display filters that are relevant for the current column only, I have applied a filter to the grid. This filter is a Telerik.Windows.Data.FilterDescriptor and is used to filter the little grid inside the custom control. It should not be confused with the DomainDataSource.FilterDescriptors collection that RadGridView is actually bound to. These are the RIA filters. Additionally, I have added several other features. For example, if you have specified a DataFormatString on your original column, the Value column inside the custom control will pick it up and format the filter values accordingly. Also, I have transferred the data type of the column that you are filtering to the Value column of the custom control. This will help the little RadGridView determine what kind of editor to show up when you begin edit, for example a date picker for DateTime columns. Finally, I have added four buttons two of them can be used to add or remove filters and the other two will communicate the changes you have made to the server. Here is the full source code of the DomainDataSourceFilteringControl. The XAML: <UserControl x:Class="PureServerSideFiltering.DomainDataSourceFilteringControl" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:telerikGrid="clr-namespace:Telerik.Windows.Controls;assembly=Telerik.Windows.Controls.GridView" xmlns:telerik="clr-namespace:Telerik.Windows.Controls;assembly=Telerik.Windows.Controls" Width="300"> <Border x:Name="LayoutRoot" BorderThickness="1" BorderBrush="#FF8A929E" Padding="5" Background="#FFDFE2E5"> <Grid> <Grid.RowDefinitions> <RowDefinition Height="Auto"/> <RowDefinition Height="150"/> <RowDefinition Height="Auto"/> </Grid.RowDefinitions> <StackPanel Grid.Row="0" Margin="2" Orientation="Horizontal" HorizontalAlignment="Center"> <telerik:RadButton Name="addFilterButton" Click="OnAddFilterButtonClick" Content="Add Filter" Margin="2" Width="96"/> <telerik:RadButton Name="removeFilterButton" Click="OnRemoveFilterButtonClick" Content="Remove Filter" Margin="2" Width="96"/> </StackPanel> <telerikGrid:RadGridView Name="filtersGrid" Grid.Row="1" Margin="2" ItemsSource="{Binding FilterDescriptors}" AddingNewDataItem="OnFilterGridAddingNewDataItem" ColumnWidth="*" ShowGroupPanel="False" AutoGenerateColumns="False" CanUserResizeColumns="False" CanUserReorderColumns="False" CanUserFreezeColumns="False" RowIndicatorVisibility="Collapsed" IsFilteringAllowed="False" CanUserSortColumns="False"> <telerikGrid:RadGridView.Columns> <telerikGrid:GridViewComboBoxColumn DataMemberBinding="{Binding Operator}" UniqueName="Operator"/> <telerikGrid:GridViewDataColumn Header="Value" DataMemberBinding="{Binding Value.Value}" UniqueName="Value"/> </telerikGrid:RadGridView.Columns> </telerikGrid:RadGridView> <StackPanel Grid.Row="2" Margin="2" Orientation="Horizontal" HorizontalAlignment="Center"> <telerik:RadButton Name="filterButton" Click="OnApplyFiltersButtonClick" Content="Apply Filters" Margin="2" Width="96"/> <telerik:RadButton Name="clearButton" Click="OnClearFiltersButtonClick" Content="Clear Filters" Margin="2" Width="96"/> </StackPanel> </Grid> </Border> </UserControl> And the code-behind: using System; using System.Collections.Generic; using System.Linq; using System.Net; using System.Windows; using System.Windows.Controls; using System.Windows.Documents; using System.Windows.Input; using System.Windows.Media; using System.Windows.Media.Animation; using System.Windows.Shapes; using Telerik.Windows.Controls.GridView; using System.Windows.Data; using Telerik.Windows.Controls; using Telerik.Windows.Data; namespace PureServerSideFiltering { /// <summary> /// A custom filtering control capable of filtering purely server-side. /// </summary> public partial class DomainDataSourceFilteringControl : UserControl, IFilteringControl { // The main player here. DomainDataSource domainDataSource; // This is the name of the property that this column displays. private string dataMemberName; // This is the type of the property that this column displays. private Type dataMemberType; /// <summary> /// Identifies the <see cref="IsActive"/> dependency property. /// </summary> /// <remarks> /// The state of the filtering funnel (i.e. full or empty) is bound to this property. /// </remarks> public static readonly DependencyProperty IsActiveProperty = DependencyProperty.Register( "IsActive", typeof(bool), typeof(DomainDataSourceFilteringControl), new PropertyMetadata(false)); /// <summary> /// Gets or sets a value indicating whether the filtering is active. /// </summary> /// <remarks> /// Set this to true if you want to lit-up the filtering funnel. /// </remarks> public bool IsActive { get { return (bool)GetValue(IsActiveProperty); } set { SetValue(IsActiveProperty, value); } } /// <summary> /// Gets or sets the domain data source. /// We need this in order to work on its FilterDescriptors collection. /// </summary> /// <value>The domain data source.</value> public DomainDataSource DomainDataSource { get { return this.domainDataSource; } set { this.domainDataSource = value; } } public System.Windows.Data.FilterDescriptorCollection FilterDescriptors { get { return this.DomainDataSource.FilterDescriptors; } } public DomainDataSourceFilteringControl() { InitializeComponent(); } public void Prepare(GridViewBoundColumnBase column) { this.LayoutRoot.DataContext = this; if (this.DomainDataSource == null) { // Sorry, but we need a DomainDataSource. Can't do anything without it. return; } // This is the name of the property that this column displays. this.dataMemberName = column.GetDataMemberName(); // This is the type of the property that this column displays. // We need this in order to see which FilterOperators to feed to the combo-box column. this.dataMemberType = column.DataType; // We will use our magic Type extension method to see which operators are applicable for // this data type. You can go to the extension method body and see what it does. ((GridViewComboBoxColumn)this.filtersGrid.Columns["Operator"]).ItemsSource = this.dataMemberType.ApplicableFilterOperators(); // This is very nice as well. We will tell the Value column its data type. In this way // RadGridView will pick up the best editor according to the data type. For example, // if the data type of the value is DateTime, you will be editing it with a DatePicker. // Nice! ((GridViewDataColumn)this.filtersGrid.Columns["Value"]).DataType = this.dataMemberType; // Yet another nice feature. We will transfer the original DataFormatString (if any) to // the Value column. In this way if you have specified a DataFormatString for the original // column, you will see all filter values formatted accordingly. ((GridViewDataColumn)this.filtersGrid.Columns["Value"]).DataFormatString = column.DataFormatString; // This is important. Since our little filtersGrid will be bound to the entire collection // of this.domainDataSource.FilterDescriptors, we need to set a Telerik filter on the // grid so that it will display FilterDescriptor which are relevane to this column ONLY! Telerik.Windows.Data.FilterDescriptor columnFilter = new Telerik.Windows.Data.FilterDescriptor("PropertyPath" , Telerik.Windows.Data.FilterOperator.IsEqualTo , this.dataMemberName); this.filtersGrid.FilterDescriptors.Add(columnFilter); // We want to listen for this in order to activate and de-activate the UI funnel. this.filtersGrid.Items.CollectionChanged += this.OnFilterGridItemsCollectionChanged; } /// <summary> // Since the DomainDataSource is a little bit picky about adding uninitialized FilterDescriptors // to its collection, we will prepare each new instance with some default values and then // the user can change them later. Go to the event handler to see how we do this. /// </summary> void OnFilterGridAddingNewDataItem(object sender, GridViewAddingNewEventArgs e) { // We need to initialize the new instance with some values and let the user go on from here. System.Windows.Data.FilterDescriptor newFilter = new System.Windows.Data.FilterDescriptor(); // This is a must. It should know what member it is filtering on. newFilter.PropertyPath = this.dataMemberName; // Initialize it with one of the allowed operators. // TypeExtensions.ApplicableFilterOperators method for more info. newFilter.Operator = this.dataMemberType.ApplicableFilterOperators().First(); if (this.dataMemberType == typeof(DateTime)) { newFilter.Value.Value = DateTime.Now; } else if (this.dataMemberType == typeof(string)) { newFilter.Value.Value = "<enter text>"; } else if (this.dataMemberType.IsValueType) { // We need something non-null for all value types. newFilter.Value.Value = Activator.CreateInstance(this.dataMemberType); } // Let the user edit the new filter any way he/she likes. e.NewObject = newFilter; } void OnFilterGridItemsCollectionChanged(object sender, System.Collections.Specialized.NotifyCollectionChangedEventArgs e) { // We are active only if we have any filters define. In this case the filtering funnel will lit-up. this.IsActive = this.filtersGrid.Items.Count > 0; } private void OnApplyFiltersButtonClick(object sender, RoutedEventArgs e) { if (this.DomainDataSource.IsLoadingData) { return; } // Comment this if you want the popup to stay open after the button is clicked. this.ClosePopup(); // Since this.domainDataSource.AutoLoad is false, this will take into // account all filtering changes that the user has made since the last // Load() and pull the new data to the client. this.DomainDataSource.Load(); } private void OnClearFiltersButtonClick(object sender, RoutedEventArgs e) { if (this.DomainDataSource.IsLoadingData) { return; } // We want to remove ONLY those filters from the DomainDataSource // that this control is responsible for. this.DomainDataSource.FilterDescriptors .Where(fd => fd.PropertyPath == this.dataMemberName) // Only "our" filters. .ToList() .ForEach(fd => this.DomainDataSource.FilterDescriptors.Remove(fd)); // Bye-bye! // Comment this if you want the popup to stay open after the button is clicked. this.ClosePopup(); // After we did our housekeeping, get the new data to the client. this.DomainDataSource.Load(); } private void OnAddFilterButtonClick(object sender, RoutedEventArgs e) { if (this.DomainDataSource.IsLoadingData) { return; } // Let the user enter his/or her requirements for a new filter. this.filtersGrid.BeginInsert(); this.filtersGrid.UpdateLayout(); } private void OnRemoveFilterButtonClick(object sender, RoutedEventArgs e) { if (this.DomainDataSource.IsLoadingData) { return; } // Find the currently selected filter and destroy it. System.Windows.Data.FilterDescriptor filterToRemove = this.filtersGrid.SelectedItem as System.Windows.Data.FilterDescriptor; if (filterToRemove != null && this.DomainDataSource.FilterDescriptors.Contains(filterToRemove)) { this.DomainDataSource.FilterDescriptors.Remove(filterToRemove); } } private void ClosePopup() { System.Windows.Controls.Primitives.Popup popup = this.ParentOfType<System.Windows.Controls.Primitives.Popup>(); if (popup != null) { popup.IsOpen = false; } } } } Finally, we need to tell RadGridViews Columns to use this custom control instead of the default one. Here is how to do it: using System; using System.Collections.Generic; using System.Linq; using System.Net; using System.Windows; using System.Windows.Controls; using System.Windows.Documents; using System.Windows.Input; using System.Windows.Media; using System.Windows.Media.Animation; using System.Windows.Shapes; using System.Windows.Data; using Telerik.Windows.Data; using Telerik.Windows.Controls; using Telerik.Windows.Controls.GridView; namespace PureServerSideFiltering { public partial class MainPage : UserControl { public MainPage() { InitializeComponent(); this.grid.AutoGeneratingColumn += this.OnGridAutoGeneratingColumn; // Uncomment this if you want the DomainDataSource to start pre-filtered. // You will notice how our custom filtering controls will correctly read this information, // populate their UI with the respective filters and lit-up the funnel to indicate that // filtering is active. Go ahead and try it. this.employeesDataSource.FilterDescriptors.Add(new System.Windows.Data.FilterDescriptor("Title", System.Windows.Data.FilterOperator.Contains, "Assistant")); this.employeesDataSource.FilterDescriptors.Add(new System.Windows.Data.FilterDescriptor("HireDate", System.Windows.Data.FilterOperator.IsGreaterThan, new DateTime(1998, 12, 31))); this.employeesDataSource.FilterDescriptors.Add(new System.Windows.Data.FilterDescriptor("HireDate", System.Windows.Data.FilterOperator.IsLessThanOrEqualTo, new DateTime(1999, 12, 31))); this.employeesDataSource.Load(); } /// <summary> /// First of all, we will need to replace the default filtering control /// of each column with out custom filtering control DomainDataSourceFilteringControl /// </summary> private void OnGridAutoGeneratingColumn(object sender, GridViewAutoGeneratingColumnEventArgs e) { GridViewBoundColumnBase dataColumn = e.Column as GridViewBoundColumnBase; if (dataColumn != null) { // We do not like ugly dates. if (dataColumn.DataType == typeof(DateTime)) { dataColumn.DataFormatString = "{0:d}"; // Short date pattern. // Notice how this format will be later transferred to the Value column // of the grid that we have inside the DomainDataSourceFilteringControl. } // Replace the default filtering control with our. dataColumn.FilteringControl = new DomainDataSourceFilteringControl() { // Let the control know about the DDS, after all it will work directly on it. DomainDataSource = this.employeesDataSource }; // Finally, lit-up the filtering funnel through the IsActive dependency property // in case there are some filters on the DDS that match our column member. string dataMemberName = dataColumn.GetDataMemberName(); dataColumn.FilteringControl.IsActive = this.employeesDataSource.FilterDescriptors .Where(fd => fd.PropertyPath == dataMemberName) .Count() > 0; } } } } The best part is that we are not only writing filters for the DomainDataSource we can read and load them. If the DomainDataSource has some pre-existing filters (like I have created in the code above), our control will read them and will populate its UI accordingly. Even the filtering funnel will light-up! Remember, the funnel is controlled by the IsActive property of our control. While this is just a basic implementation, the source code is absolutely yours and you can take it from here and extend it to match your specific business requirements. Below the main grid there is another debug grid. With its help you can monitor what filter descriptors are added and removed to the domain data source. Download Source Code. (You will have to have the AdventureWorks sample database installed on the default SQLExpress instance in order to run it.) Enjoy!Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

Read the article

WCF AuthenticationService in IIS7 Error

- by germandb

I have a WCF Server running on IIS 7 using default application pool, with SSL activate, the services is installed in a SBS Server 2008. I implement client application services with wcf and SQL 2005 for setting the access control in my application. The application run under windows vista and is make with WPF. In my developer machine the application and the WCF services run well, the IIS i'm use for the trials is the local IIS 7 and the database is the SQL Server 2005 database hosting in my server. I'm using Visual Studio Project Designer to enable and configure client application services. using https://localhost/WcfServidorFundacion. When i'm change the authentication services location to https://WcfServices:5659/WcfServidorFundacion and recompile the application, the following error show up. Message: The web service returned the error status code: InternalServerError. Details of service failure: {"Message":" Error while processing your request ","StackTrace":"","ExceptionType":""} Stack Trace: en System.Net.HttpWebRequest.GetResponse() en System.Web.ClientServices.Providers.ProxyHelper.CreateWebRequestAndGetResponse(String serverUri, CookieContainer& cookies, String username, String connectionString, String connectionStringProvider, String[] paramNames, Object[] paramValues, Type returnType) InnerException: System.Net.WebException Message="Remote Server Error: (500) Interal Server Error." I can access the WCF service from the navigator using the url mentioned above and even make a webReference in my project. I make a capture of the response but I'cant post it because i don't have 10 reputation points I activate the error log in the IIS 7 server, and the result is a Warning in the ManagedPipilineHandler. I appreciate if any one can help me Errors & Warnings No.? Severity Event Module Name 132. view trace Warning -MODULE_SET_RESPONSE_ERROR_STATUS ModuleName ManagedPipelineHandler Notification 128 HttpStatus 500 HttpReason Internal Server Error HttpSubStatus 0 ErrorCode 0 ConfigExceptionInfo Notification EXECUTE_REQUEST_HANDLER ErrorCode La operación se ha completado correctamente. (0x0) Maybe this can help, is the web.config of my service <?xml version="1.0" encoding="utf-8"?>  <configuration> <configSections> <sectionGroup name="system.web.extensions" type="System.Web.Configuration.SystemWebExtensionsSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <sectionGroup name="scripting" type="System.Web.Configuration.ScriptingSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="scriptResourceHandler" type="System.Web.Configuration.ScriptingScriptResourceHandlerSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <sectionGroup name="webServices" type="System.Web.Configuration.ScriptingWebServicesSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="jsonSerialization" type="System.Web.Configuration.ScriptingJsonSerializationSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="Everywhere" /> <section name="profileService" type="System.Web.Configuration.ScriptingProfileServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="authenticationService" type="System.Web.Configuration.ScriptingAuthenticationServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="roleService" type="System.Web.Configuration.ScriptingRoleServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> </sectionGroup> </sectionGroup> </sectionGroup> </configSections> <appSettings /> <connectionStrings> <remove name="LocalMySqlServer" /> <remove name="LocalSqlServer" /> <add name="fundacionSelfAut" connectionString="Data Source=FUNDACIONSERVER/PRUEBAS;Initial Catalog=fundacion;User ID=wcfBaseDatos;Password=qwerty_2009;" providerName="System.Data.SqlClient" /> </connectionStrings> <system.web> <profile enabled="true" defaultProvider="SqlProfileProvider"> <providers> <clear /> <add name="SqlProfileProvider" type="System.Web.Profile.SqlProfileProvider" connectionStringName="fundacionSelfAut" applicationName="fundafe" /> </providers> <properties> <add name="FirstName" type="String" /> <add name="LastName" type="String" /> <add name="PhoneNumber" type="String" /> </properties> </profile> <roleManager enabled="true" defaultProvider="SqlRoleProvider"> <providers> <clear /> <add name="SqlRoleProvider" type="System.Web.Security.SqlRoleProvider" connectionStringName="fundacionSelfAut" applicationName="fundafe" /> </providers> </roleManager> <membership defaultProvider="SqlMembershipProvider"> <providers> <clear /> <add name="SqlMembershipProvider" type="System.Web.Security.SqlMembershipProvider" connectionStringName="fundacionSelfAut" applicationName="fundafe" enablePasswordRetrieval="false" enablePasswordReset="false" requiresQuestionAndAnswer="true" requiresUniqueEmail="true" passwordFormat="Hashed" /> </providers> </membership> <authentication mode="Forms" /> <compilation debug="true" strict="false" explicit="true"> <assemblies> <add assembly="System.Core, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> <add assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </assemblies> </compilation>   <pages> <controls> <add tagPrefix="asp" namespace="System.Web.UI" assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </controls> </pages> <httpHandlers> <remove verb="*" path="*.asmx" /> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add verb="*" path="*_AppService.axd" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" validate="false" /> </httpHandlers> <httpModules> <add name="ScriptModule" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </httpModules> <sessionState timeout="40" /> </system.web> <system.codedom> <compilers> <compiler language="c#;cs;csharp" extension=".cs" warningLevel="4" type="Microsoft.CSharp.CSharpCodeProvider, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"> <providerOption name="CompilerVersion" value="v3.5" /> <providerOption name="WarnAsError" value="false" /> </compiler> </compilers> </system.codedom>  <system.webServer> <validation validateIntegratedModeConfiguration="false" /> <modules> <add name="ScriptModule" preCondition="integratedMode" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </modules> <handlers> <remove name="WebServiceHandlerFactory-Integrated" /> <add name="ScriptHandlerFactory" verb="*" path="*.asmx" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="ScriptHandlerFactoryAppServices" verb="*" path="*_AppService.axd" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="ScriptResource" preCondition="integratedMode" verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </handlers> <tracing> <traceFailedRequests> <add path="*"> <traceAreas> <add provider="ASP" verbosity="Verbose" /> <add provider="ASPNET" areas="Infrastructure,Module,Page,AppServices" verbosity="Verbose" /> <add provider="ISAPI Extension" verbosity="Verbose" /> <add provider="WWW Server" areas="Authentication,Security,Filter,StaticFile,CGI,Compression,Cache,RequestNotifications,Module" verbosity="Verbose" /> </traceAreas> <failureDefinitions statusCodes="401.3,500,403,404,405" /> </add> </traceFailedRequests> </tracing> <security> <authorization> <add accessType="Allow" users="germanbarbosa,informatica" /> </authorization> <authentication> <windowsAuthentication enabled="false" /> </authentication> </security> </system.webServer> <system.web.extensions> <scripting> <webServices> <authenticationService enabled="true" requireSSL="true" /> <profileService enabled="true" readAccessProperties="FirstName,LastName,PhoneNumber" /> <roleService enabled="true" /> </webServices> </scripting> </system.web.extensions> <system.serviceModel> <services>  <service behaviorConfiguration="AppServiceBehaviors" name="System.Web.ApplicationServices.AuthenticationService"> <endpoint address="" binding="basicHttpBinding" bindingConfiguration="userHttps" bindingNamespace="http://asp.net/ApplicationServices/v200" contract="System.Web.ApplicationServices.AuthenticationService" /> </service>  <service behaviorConfiguration="AppServiceBehaviors" name="System.Web.ApplicationServices.RoleService"> <endpoint binding="basicHttpBinding" bindingConfiguration="userHttps" bindingNamespace="http://asp.net/ApplicationServices/v200" contract="System.Web.ApplicationServices.RoleService" /> </service>  <service behaviorConfiguration="AppServiceBehaviors" name="System.Web.ApplicationServices.ProfileService"> <endpoint binding="basicHttpBinding" bindingNamespace="http://asp.net/ApplicationServices/v200" bindingConfiguration="userHttps" contract="System.Web.ApplicationServices.ProfileService" /> </service> </services> <bindings> <basicHttpBinding>  <binding name="userHttps"> <security mode="Transport"> </security> </binding> </basicHttpBinding> </bindings> <behaviors> <serviceBehaviors> <behavior name="AppServiceBehaviors"> <serviceMetadata httpGetEnabled="false" httpsGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="true" /> <serviceAuthorization principalPermissionMode="UseAspNetRoles" roleProviderName="SqlRoleProvider" /> <serviceCredentials> <userNameAuthentication userNamePasswordValidationMode="MembershipProvider" membershipProviderName="SqlMembershipProvider" /> </serviceCredentials> </behavior> </serviceBehaviors> </behaviors> <serviceHostingEnvironment aspNetCompatibilityEnabled="true" /> </system.serviceModel> </configuration>

Read the article

IIRF reverse proxy problem

- by Sergei

Hi everyone, We have a java application ( Atlassian Bamboo) running on port 8085 on Windows 2003. It is accessile as http: //bamboo:8085. I am trying to setup reverse proxy for IIS6 using IIRF so content is accessible via http: //bamboo. It seems that I set it ip correctly, and I can retrieve Status page. This is how my IIRF.ini looks like: RewriteLog c:\temp\iirf RewriteLogLevel 2 StatusUrl /iirfStatus RewriteCond %{HTTP_HOST} ^bambooi$ [I] #This setup works #ProxyPass ^/(.*)$ http://othersite/$1 #This does not ProxyPass ^/(.*)$ http://bamboo:8085/$1 However when I type in http: //bamboo in IE, I get 'page cannot be displayed ' message. FF does not return anything at all. I made Wireshark network dump, selected 'follow TCPstream' and it seems like correct page is being retrieved.Why cannot I see it then? I also noticed that I can retrieve http: //bamboo/favicon.ico so I must be very close to the solution.. This is the Wireshark output: GET / HTTP/1.1 Accept: image/gif, image/jpeg, image/pjpeg, image/pjpeg, application/x-shockwave-flash, application/vnd.ms-excel, application/vnd.ms-powerpoint, application/msword, application/x-ms-application, application/x-ms-xbap, application/vnd.ms-xpsdocument, application/xaml+xml, */* Accept-Language: en-gb User-Agent: Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Accept-Encoding: gzip, deflate Host: bamboo Connection: Keep-Alive Cookie: JSESSIONID=wpsse0zyo4g5 HTTP/1.1 200 200 OK Date: Sat, 30 Jan 2010 09:19:46 GMT Server: Microsoft-IIS/6.0 Via: 1.1 DESTINATION_IP (IIRF 2.0) Content-Type: text/html; charset=utf-8 Transfer-Encoding: chunked <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en"> <head> <title>Dashboard</title> <meta http-equiv="content-type" content="text/html; charset=UTF-8" /> <meta name="robots" content="all" /> <meta name="MSSmartTagsPreventParsing" content="true" /> <meta http-equiv="Pragma" content="no-cache" /> <meta http-equiv="Expires" content="-1" /> <link type="text/css" rel="stylesheet" href="/s/1206/1/_/scripts/yui-2.6.0/build/grids/grids.css" />  <link rel="stylesheet" href="/s/1206/1/_/styles/main.css" type="text/css" /> <link rel="stylesheet" href="/s/1206/1/_/styles/main2.css" type="text/css" /> <link rel="stylesheet" href="/s/1206/1/_/styles/global-static.css" type="text/css" /> <link rel="stylesheet" href="/s/1206/1/_/styles/widePlanList.css" type="text/css" /> <link rel="stylesheet" href="/s/1206/1/_/styles/forms.css" type="text/css" /> <link rel="stylesheet" href="/s/1206/1/_/styles/yui-support/yui-custom.css" type="text/css" /> <link rel="shortcut icon" href="/s/1206/1/_/images/icons/favicon.ico" type="image/x-icon"/> <link rel="icon" href="/s/1206/1/_/images/icons/favicon.png" type="image/png" /> <link rel="stylesheet" href="/s/1206/1/_/styles/bamboo-tabs.css" type="text/css" />  <link rel="stylesheet" type="text/css" href="/s/1206/1/_/scripts/yui-2.6.0/build/tabview/assets/tabview-core.css"> <link rel="stylesheet" type="text/css" href="/s/1206/1/_/scripts/yui-2.6.0/build/tabview/assets/skins/sam/tabview-skin.css"> <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/yahoo/yahoo-min.js"></script> <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/event/event-min.js" ></script> <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/dom/dom-min.js" ></script>   <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/container/container-min.js"></script> <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/connection/connection-min.js"></script> <link type="text/css" rel="stylesheet" href="/s/1206/1/_/scripts/yui-2.6.0/build/container/assets/container.css" />  <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/menu/menu-min.js"></script> <link type="text/css" rel="stylesheet" href="/s/1206/1/_/scripts/yui-2.6.0/build/menu/assets/menu.css" />   <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/yahoo-dom-event/yahoo-dom-event.js"></script> <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/element/element-beta-min.js"></script>  <link rel="stylesheet" href="/s/1206/1/_/styles/yui-support/tabview.css" type="text/css" /> <link rel="stylesheet" href="/s/1206/1/_/styles/yui-support/round_tabs.css" type="text/css" /> <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/tabview/tabview-min.js"></script> <script type="text/javascript" src="/s/1206/1/_/scripts/yui-2.6.0/build/json/json-min.js"></script> <script type="text/javascript" src="/s/1206/1/_/scripts/yui-ext/yui-ext-nogrid.js"></script> <script type="text/javascript" src="/s/1206/1/_/scripts/bamboo.js"></script> <script type="text/javascript"> YAHOO.namespace('bamboo'); YAHOO.bamboo.tooltips = new Object(); YAHOO.bamboo.contextPath = ''; YAHOO.ext.UpdateManager.defaults.loadScripts = true; YAHOO.ext.UpdateManager.defaults.indicatorText = '<div class="loading-indicator">Currently loading...</div>'; YAHOO.ext.UpdateManager.defaults.timeout = 60; addUniversalOnload(addConfirmationToLinks); </script> <link rel="alternate" type="application/rss+xml" title="Bamboo RSS feed" href="/rss/createAllBuildsRssFeed.action?feedType=rssAll" /> </head> <body> <ul id="top"> <li id="skipNav"> <a href="#menu">Skip to navigation</a> </li> <li> <a href="#content">Skip to content</a> </li> </ul> <div id="nonFooter"> <div id="hd"> <div id="header"> <div id="logo"> <a href="/start.action"><img src="/images/bamboo_header_logo.gif" alt="Atlassian Bamboo" height="36" width="118" /></a> </div> <ul id="userOptions"> <li id="loginLink"> <a id="login" href="/userlogin!default.action?os_destination=%2Fstart.action">Log in</a> </li> <li id="signupLink"> <a id="signup" href="/signupUser!default.action">Signup</a> </li> <li id="helpLink"> <a id="help" href="http://confluence.atlassian.com/display/BAMBOO">Help</a> </li> </ul> </div>  <div id="menu"> <ul> <li><a id="home" href="/start.action" title="Atlassian Bamboo" accesskey="H"> <u>H</u>ome</a></li> <li><a id="authors" href="/authors/gotoAuthorReport.action" accesskey="U">A<u>u</u>thors</a></li> <li><a id="reports" href="/reports/viewReport.action" accesskey="R"> <u>R</u>eports</a></li> </ul> </div>  </div>  <div id="bd"> <div id="content"> <h1>Header here</h1> <div class="topMarginned"> <div id='buildSummaryTabs' class='dashboardTab'> </div> <script type="text/javascript"> function initUI(){ var jtabs = new YAHOO.ext.TabPanel('buildSummaryTabs'); YAHOO.bamboo.tabPanel = jtabs; // Use setUrl for Ajax loading var tab3 = jtabs.addTab('allTab', "All Plans"); tab3.setUrl('/ajax/displayAllBuildSummaries.action', null, true); var tab4 = jtabs.addTab("currentTab", "Current Activity"); tab4.setUrl('/ajax/displayCurrentActivity.action', null, true); var handleTabChange = function(e, activePanel) { saveCookie('atlassian.bamboo.dashboard.tab.selected', activePanel.id, 365); }; jtabs.on('tabchange', handleTabChange); var selectedCookie = getCookieValue('atlassian.bamboo.dashboard.tab.selected'); if (jtabs.getTab(selectedCookie)) { jtabs.activate(selectedCookie); } else { jtabs.activate('allTab'); } } YAHOO.util.Event.onContentReady('buildSummaryTabs', initUI); </script> </div> <script type="text/javascript"> setTimeout( "window.location.reload()", 1800*1000 ); </script> <div class="clearer" ></div> </div>  </div>  </div>  <div id="ft"> <div id="footer"> <p> Powered by <a href="http://www.atlassian.com/software/bamboo/">Atlassian Bamboo</a> version 2.2.1 build 1206 - <span title="15:59:44 17 Mar 2009">17 Mar 09</span> </p> <ul> <li class="first"> <a href="https://support.atlassian.com/secure/CreateIssue.jspa?pid=10060&issuetype=1">Report a problem</a> </li> <li> <a href="http://jira.atlassian.com/secure/CreateIssue.jspa?pid=11011&issuetype=4">Request a feature</a> </li> <li> <a href="http://forums.atlassian.com/forum.jspa?forumID=103">Contact Atlassian</a> </li> <li> <a href="/viewAdministrators.action">Contact Administrators</a> </li> </ul> </div>  </div>

Read the article

How TiVo is messing up customer support.

- by James Fleming

Ok, So I've gotten a TiVo and overall, I'm happy, but there have been issues and I suspect I've a defective unit. - Now the nice folks after many service calls were happy to swap it out, and to ensure continuity of service, they sent me a new unit (after a $109 deposit). That was yesterday. Today, when we go to watch a little TV, and wait for our replacement unit to arrive we find our TiVo service has been suspended. WTF? They have an exchange program, but your unit your waiting to exchange is as dead as a doornail until the replacement arrives. How hard is it to keep the old unit active for an extra week? Here is the exchange w/Tivo below... You are currently number 1 in the queue. We apologize for the delay. We will assign you to an agent as soon as one is available.The average amount of time a customer has to wait is 00:13. Kaylene (Listening) Kaylene: Thank you for contacting TiVo! My name is Kaylene. So that I may better assist you, are you an existing customer? james Fleming: yes I am, but I'm now having second thoughts about being one Kaylene: Thank you for verifying your information. How may I assist you today James? james Fleming: I've been having issues w/a tivo box & I'm getting a replacement sent out to me (after paying an additional deposit) and now my current unit is no longer activated Kaylene: I can help you today! Kaylene: When we process an exchange we do transfer over the service to the replacement box so it is active and ready to go when you receive it. james Fleming: which is to say you also make my current box worthless until such time I receive a new box?!?!? Kaylene: I apologize that your original box was deactivated so we could activate your replacement box. james Fleming: Why on Earth would I bother to pay in advance for a new box if you were going to kill my existing box. Kaylene: What features are you needing to use on your current box? james Fleming: I need to be able to access my netflix subscription (if I'm lucky enough to have it work without rebooting) Kaylene: Can I have you verify the TiVo Service Number of your TiVo box please? james Fleming: 7460011906979b4 Kaylene: We have your current box temporary service but not all features are available with temporary service as it is not paid for service. Kaylene: If you like I can transfer your service back to your current box for now. Then once you receive the new box you will have to call in and have the service transferred back to the new box. james Fleming: Not paid for? Let's see> one tivo box + 3 year service plan + monthly service + $109 deposit on a second box = what? Kaylene: Would you like me to transfer your service back to your current box? james Fleming: Yes - that would be helpful Kaylene: All you will need to do is contact us again once you receive the new box so we can transfer it back. Kaylene: I have put your service back on TiVo box 7460011906979b4. james Fleming: What would also be helpful is your firm informing me to how you'd be cutting service in the interim. james Fleming: Again - I opted to pay to have a second box delivered BEFORE returning the box I have - thus trying to have a continuity of service.. Kaylene: This is not something we normally do so it is important when you contact us to transfer the service back to the new box when you receive it that you reference this case number: 110622-006089. Kaylene: I apologize about the inconvenience. You may need force a few connections for the box to recognize the service again. james Fleming: If it's not something you normally do than WHY would you have a $109 fee and a term for the service. james Fleming: I am not mad at you, but your company is not impressing me and I'm blogging about this experience Kaylene: Again I apologize about the inconvenience but you should be good to go now. Is there anything else I can help you with today? james Fleming: so I need to go through the re-actviate process or is that somethign you do Kaylene: When you receive the new TiVo box you need to contact us so we can transfer the service to the new box for you. james Fleming: sure Kaylene: Is there anything else I can help you with today James? james Fleming: Nope - please email this transcript to me Kaylene: I apologize but we do not have the ability to e-mail you a copy of this transcript. You can view it online at http://www.tivo.com when you sign into your account or you can copy and paste it now to save it. Kaylene: Thank you for contacting TiVo today. Your reference number for our conversation is 110622-006089. You can save this for your records, and if necessary, provide this to a later agent to pull up what we discussed. There will be a brief satisfaction survey emailed to you. We would appreciate any feedback on your TiVo Chat Support experience today. Kaylene: Thank you for using TiVo Chat and have a great day James! Good-bye. Kaylene has disconnected.

Read the article

Oracle Open World 2012: SQL Developer Recap

- by thatjeffsmith

Last week was the ‘big show’ in San Francisco. I was very happy to meet many of you in person. And many of you had questions – lots of questions! We had full or overflowing rooms for our sessions and hands-on-labs. The SQL Developer ‘booths’ were also slammed several times. So exciting to see so many of YOU excited about SQL Developer. It’s very cool to hear the stories of our tools saving you and your organizations so much time (and money!) Instead of doing a Day 0 – Day 9 recap, I thought I’d share with you the questions that I heard more than once. And just for giggles, I’ll throw in some answers as well So in no particular order… What’s the difference between Oracle SQL Developer & Oracle SQL Developer Data Modeler? Mathematically speaking – two words. But as far as the actual modeling features go, there’s no difference between the two applications. The same ‘code’ or features as it pertains to data modeling and design are in both tools. However, in SQL Developer you have all of the OTHER features fighting for real estate in the UI. So I have a general rule of thumb – if you spend MOST of your time in the database, use SQL Developer. And if you spend most of your time in the data model, run the separate and dedicated program, Oracle SQL Developer Data Modeler. Here’s a couple of screenshots to drive home the UI point: Oracle SQL Developer Oracle SQL Developer Data Modeler running INSIDE of SQL Developer. Notice how the Modeler menu items fold under the file menu? Oracle SQL Developer Data Modeler Easier to navigate and manipulate your models with the stand alone modeler. Just no worksheet to run your ad-hoc queries, etc. Don’t forget you can disable the Data Modeler inside of SQL Developer via the Extensions preference page. How can I model my table partitions? Partitioning is defined via the Physical model. So after you have finished your relational model, you need to generate a physical model. Oracle SQL Developer Data Modeler Physical Model and Partitioning Open the properties for your physical model table. Enable the ‘partitioned’ property. Once you do so, the ‘Partitioning’ page will activate. Lots and lots of partitioning support and options here But what about Interval Partitioning? An extension of range partitioning in 11gR2, we don’t currently support this partitioning scheme in SQL Developer. But we’re working on it! Can SQL Developer ignore column order when comparing models? Yes! After you start a model compare, one of your options is to disregard the order of an attribute or column definition. Tell SQL Developer you don’t care when your column shows up, just as long as it DOES show up. Wow, you got a lot of questions around modeling! Is that normal? Yes! While we appreciate that many folks inherit their applications and associated designs, new applications are being ‘born’ every day. Since both of our tools are free for anyone to design their new Oracle applications with, we attract a fair amount of attention I want to do a Hands On Lab. How do I get your software and instructional guides? Go here. Download VirtualBox. Then download the VB image. Import the appliance. Start it. Connect oracle/oracle on the OEL VM. Click on ‘Start Here’ in the desktop. Follow the instructions. If you need help, ask away! You went too fast in your Tips & Tricks session. Do you have cliff notes? Yes! And you’re SO close to finding them! Just go to my SQL Developer resources page. All of my tips are documented on this blog somewhere. I’ve indexed the most popular ones on the resource page. You can use the Search dialog on the right to find the rest. Or just send me a comment or question, and I’ll do my best to answer them as they come in.

Read the article

Simultaneously calling multiple methods on a WCF service from silverlight

- by ola karlsson

A while back I had to debug some performance issues in an existing Silverlight app, as the problem / solution was a bit obscure and finding info about it was quite tricky, I thought I’d share, maybe it can help the next person with this problem. The App On start, the app would do a number of calls to different methods on a WCF service, this to populate the UI with the necessary data. Recently one of those services had been changed and was now taking quite a bit longer than it used to. This was resulting in quite a long loading time for the whole UI, which was set up so it wouldn’t let the user interact with anything, until all the service calls had finished. First I broke out the longer running service call from the others, then removed the constraint that it had to be loaded for the UI in general to become responsive. I also added a loading indicator just on that area of the UI, thinking that the main UI would load while this particular section could keep loading independently. The Problem However this is where things started to get a bit strange. I found that even after these changes, the main UI wouldn’t activate until the long running call returned. So now, I did what I should have done to start with, I got Fiddler out and had a look at what was really happening. What I found was that, once the call to the long running service method was placed, all subsequent call were waiting for that one to return before executing. Not having really worked with WCF previously or knowing much about it in general, I was stumped… I knew of the issues where Silverlight is restricted by the browsers networking features in regards to number of simultaneous connections etc. However that just didn’t seem to be the issue here, you can clearly see in Fiddler that there’s numerous calls, but they’re just not returning. I thought of the problem maybe being in the WCF service, but the calls were really not that complicated and surely the service should be able to handle a lot more than what I was throwing at it! So I did what every developer does in this type of scenario, I hit the search engines. I did a whole bunch of searching on things like “multiple simultaneous WCF calls from Silverlight” and “Calling long running WCF services from Silverlight” etc. etc. This however, pretty much got me nowhere, I found a whole heap of resources on how to do WCF calls from Silverlight but most of them were very basic and of no use what so ever. The fog is clearing It wasn’t until I came across the term “ WCF blocking calls” and started incorporating that in my searches I started to get somewhere. Those searches quite quickly brought me to the following thread in the Silverlight forum “Long-running WCF call blocking subsequent calls” which discussed the exact problem I was facing and the best part, one of the guys there had the solution! The short answer is in the forum post and the guys answering, has also done a more extensive blog post about it called “Silverlight, WCF, and ASP.Net Configuration Gotchas” which covers it very well. So come on what’s the solution?! I heard you ask, unless you’ve already gone to the links and looked it up ;) The Solution Well, it turns out that the issue is founded in a mix of Silverlight, Asp.Net and WCF, basically if you’re doing multiple calls to a single WCF web-service and you have Asp.Net session state enabled, the calls will be executed sequentially by the service, hence any long running calls will block subsequent ones. So why is Asp.Net session state effecting us, we’re working in Silverlight, right? We'll as mentioned earlier, by default Silverlight uses the browsers networking stack when doing service calls, hence to the WCF service, the call looks like it might as well be coming from a normal Asp.Net. To get around this, we look to a feature introduced in Silverlight 3, namely the Client HTTP Stack. The Client HTTP Stack to the rescue By using the following syntax (for example in our App.xaml.cs, Application_Startup method) WebRequest.RegisterPrefix("http://", WebRequestCreator.ClientHttp); we can set our Silverlight application to use the Client HTTP Stack, which incidentally solves our problem! By using Silverlights own networking stack, rather than that of the browser, we get around the Asp.Net - WCF session state issue. The above code specifies that all calls to addresses starting with “http://” should go through the client stack, this can actually be set more granular and you can specify it to be used only for certain domains etc. Summary The actual solution is well covered in the forum and blog posts I link to above. This post is more about sharing my experience, hopefully helping to spread the word about this and maybe make it a bit easier for the next poor guy with this issue to find the solution. Until next time, Ola

Read the article

doubleTwist is an iTunes Alternative that Supports Several Devices

- by Mysticgeek

There are a lot of iTunes users out there, but unfortunately you can’t use it with all of your portable devices. Today we take a look at doubleTwist, which allows you to sync your media with a multitude of portable devices and easily share it as well. Note: You can run doubleTwist on Windows or Mac, and here we take a look at the Windows version. Install & Setup doubleTwist Download and install doubleTwist using the defaults in the wizard… Installation takes several moments and you’ll see the progress while it finishes up. After installation is complete, sign up for an account if you don’t already have one. If you do have an account you can login right away. Enter in your username, email address, and password then click Sign Up. You’ll get an confirmation email and need to activate the account before you can sign in. Once you’re all signed up, launch doubleTwist and you’ll be ready to start using it. doubleTwist Music The default music store is Amazon MP3 store which might appeal to those of you who are tired of the iTunes music store. A lot of times the music is cheaper and available at higher bit rates. You can start searching for music in the Amazon Music Store and previewing songs. To purchase anything though you will need to sign into your Amazon account. Under Playlists it allows you to import your playlists from iTunes and Windows Media Player, which is a handy feature if you don’t want to set them up again. Of course you can play your songs through the music player on your desktop. Devices One of the coolest things about doubleTwist is that it supports a lot of different portable media devices including iPod, BlackBerry, Windows Mobile, Android, PSP, Smartphones, and much more. Unfortunately for Zune users…there isn’t any support for the Zune of Zune HD yet. Here we have a Creative Zen attached and can sync songs, pictures, and podcasts. An HTC-S620 Smartphone running Windows Mobile… Even a simple USB drive will be recognized and you can transfer your media to it as well. Podcasts Finding your favorite audio and video podcasts is easy with the search feature. You can easily manage and subscribe to podcasts in the subscriptions section. You can watch the video podcasts directly in doubleTwist. Sharing Media Also you can share digital media with your friends or add it to Flickr and YouTube. You can send any pictures, videos, or music in your library to other people by dragging it over. You can email users individually… Or access contacts from your Gmail and Yahoo accounts. There is a limit to how much you can send of video podcasts… only the first 10 minutes. The person you send it to will get a link in their email that points to your My Feed page on the doubleTwist site. There they can access the media you sent…in this example it’s a video podcast but you can share any media. Other Features Under My Profile you can change your avatar and personal information. In Preferences you can choose where media is stored, its startup actions, podcast subscriptions, and manage device syncing. Conclusion It’s still in beta stage so expect some bugs, but overall doubleTwist is a solid media player that is easy to use with a clean interface. It’s simple and doesn’t try to do too much so is fairly easy on system resources. The main annoyance is it tries to catalog all of your media out of the box. Which may be alright for some users with smaller media collections, but very irritating to advanced users with large collections. Also there is currently no support for the Zune, but according to their forums, it’s on the way. At the time of this writing it’s in public beta and can be downloaded for XP, Vista, Windows 7 (32 & 64 bit), and Mac OSX. If you’re looking for an iTunes alternative that works with several different portable devices, you might want to give DoubleTwist a try. Download DoubleTwist Public Beta See If Your Media Device is Supported by doubleTwist Similar Articles Productive Geek Tips MusicBee is a Fast and Powerful Music ManagerAvoid the Apple QuickTime Bloat with QT LiteBeginner Geek: Set Default Programs in Windows 7 and VistaBeginner Geeks: OpenOffice is a Free Cross Platform Alternative to MS OfficeManage Devices the Easy Way with Device Stage in Windows 7 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Play Music in Chrome by Simply Dragging a File 15 Great Illustrations by Chow Hon Lam Easily Sync Files & Folders with Friends & Family Amazon Free Kindle for PC Download Stretch popurls.com with a Stylish Script (Firefox) OldTvShows.org – Find episodes of Hitchcock, Soaps, Game Shows and more

Read the article

Weekend With #iPad

- by andrewbrust

Saturday morning, I got up, got dressed and took a 7-minute walk up to the Apple Store in New York’s Meatpacking District to pick up my reserved iPad. This precinct, which borders Greenwich Village (where I live and grew up) was, when I was a kid, a very industrial and smelly neighborhood during the day and a rough neighborhood at night. So imagine my sense of irony as I walked up Hudson Street towards 14th Street, to go wait in line with a bunch of hipsters to buy an iPad on launch day. Numerous blue T-shirt-clad Apple store workers were on hand to check people in to the line specifically identified for people who had reserved an iPad. Others workers passed out water and all of them, I kid you not, applauded people as they got their chance to go into the store and buy their devices. They also cheered people and yelled “congratulations” as they left. The event had all the charm of a mass wedding officiated by Reverend Sung Myung Moon. Once inside, a nice dude named Trey, with lots of tattoos on his calves, helped me and I acquired my device in short order. Another guy helped me activate the device, which was comical, because that has to be done through iTunes, which I hadn’t logged into in a while. Turns out my user id was my email address from the company I sold 5 1/2 years ago. Who knew? Regardless, I go the device working, packed up and left the store, shuddering as I was cheered and congratulated. By this time (about 10:30am) the line for reserved units and even walk-ins, was gone. The iPhone launch this was not. As much as I detested the Apple Store experience, I must say the device is really nice. the screen is bright, the colors are bold, and the experience is ultra-smooth. I quickly tested Safari, YouTube, Google Maps, and then installed a few apps, including the New York Times Editors’ Choice and a couple of Twitter clients. Some initial raves: Google Maps and Street View on the iPad is just amazing. The screen is full-size like a PC or Mac, but it’s right in front of you and responding to taps and flicks and pinches and it’s really engulfing. Video and photos are really nice on this device, despite the fact that 16:9 and anamorphic aspect ration content is letter boxed. It still looks amazing. And apps that are designed especially for the iPad, including The Weather Channel and Gilt and Kayak just look stunning. The richness, the friendly layout, the finger-friendly UIs, and the satisfaction of not having a keyboard between you and the information you’re managing, while you sit on a couch or an easy chair, is just really a beautiful thing. The mere experience of seeing these apps’ splash screens causes a shiver and Goosebumps. Truly. The iPad is not a desktop machine, and it’s not pocket device. That doesn’t mean it’s useless though. It’s the perfect “couchtop” computer. Now some downsides: the WiFi radio seems a bit flakey. More than a few times, I have had to toggle the WiFi off and back on to get it to connect properly. Worse yet, the iPad is totally bamboozled by the fact that I have four WiFi access points in my house, each with the same SSID. My laptops are smart enough to roam from one to the other, but the iPad seems to maintain an affinity for the downstairs access point, even if I’m turning it on two flights up. Telling the iPad to “forget” my WiFi network and then re-associate with it doesn’t help. More downers: as you might expect, there are far more applications developed for the iPhone than the iPad. And although iPhone apps run on the iPad, that provides about the same experience as watching standard def on a big HD flat panel, complete with the lousy choice of thick black borders or zooming the picture in to fill the screen. And speaking of iPhone Apps, I can’t get the Sonos one to work. Ideally, they’d have a dedicated iPad app and it would work on the first try. And the iPad is just as bad as any netbook when it comes to being a magnet for fingerprints. The lack of multi-tasking is quite painful too – truly, I don’t mind if only one app can be active at once, but the lack of ability to switch between apps, and the requirement to return to the home screen and re-launch a previous app to switch back, is already old and I’ve had the thing less than 48 hours. These are just initial impressions. I’ll have a fuller analysis soon, after I’ve had some more break-in time with my new toy. I’ll be thinking not just about the iPad and iPhone but also about Android, the 2.1 update for which was pushed to my Droid today, and Windows Phone 7, whose “hub” concept I now understand the value of. This has been a great year for alternative computing devices, and I see no net downside for Apple, Google or Microsoft. Exciting times.

Read the article

International Radio Operators Alphabet in F# & Silverlight – Part 1

- by MarkPearl

So I have been delving into F# more and more and thought the best way to learn the language is to write something useful. I have been meaning to get some more Silverlight knowledge (up to now I have mainly been doing WPF) so I came up with a really simple project that I can actually use at work. Simply put – I often get support calls from clients wanting new activation codes. One of our main app’s was written in VB6 and had its own “security” where it would require about a 45 character sequence for it to be activated. The catch being that each time you reopen the program it would require a different character sequence, which meant that when we activate clients systems we have to do it live! This involves us either referring them to a website, or reading the characters to them over the phone and since nobody in the office knows the IROA off by heart we would come up with some interesting words to represent characters… 9 times out of 10 the client would type in the wrong character and we would have to start all over again… with this app I am hoping to reduce the errors of reading characters over the phone by treating it like a ham radio. My “Silverlight” application will allow for the user to input a series of characters and the system will then generate the equivalent IROA words… very basic stuff e.g. Character Input – abc Words Generated – Alpha Bravo Charlie After listening to Anders Hejlsberg on Dot Net Rocks Show 541 he mentioned that he felt many applications could make use of F# but in an almost silo basis – meaning that you would write modules that leant themselves to Functional Programming in F# and then incorporate it into a solution where the front end may be in C# or where you would have some other sort of glue. I buy into this kind of approach, so in this project I will use F# to do my very intensive “Business Logic” and will use Silverlight/C# to do the front end. F# Business Layer I am no expert at this, so I am sure to get some feedback on way I could improve my algorithm. My approach was really simple. I would need a function that would convert a single character to a string – i.e. ‘A’ –> “Alpha” and then I would need a function that would take a string of characters, convert them into a sequence of characters, and then apply my converter to return a sequence of words… make sense? Lets start with the CharToString function let CharToString (element:char) = match element.ToString().ToLower() with | "1" -> "1" | "5" -> "5" | "9" -> "9" | "2" -> "2" | "6" -> "6" | "0" -> "0" | "3" -> "3" | "7" -> "7" | "4" -> "4" | "8" -> "8" | "a" -> "Alpha" | "b" -> "Bravo" | "c" -> "Charlie" | "d" -> "Delta" | "e" -> "Echo" | "f" -> "Foxtrot" | "g" -> "Golf" | "h" -> "Hotel" | "i" -> "India" | "j" -> "Juliet" | "k" -> "Kilo" | "l" -> "Lima" | "m" -> "Mike" | "n" -> "November" | "o" -> "Oscar" | "p" -> "Papa" | "q" -> "Quebec" | "r" -> "Romeo" | "s" -> "Sierra" | "t" -> "Tango" | "u" -> "Uniform" | "v" -> "Victor" | "w" -> "Whiskey" | "x" -> "XRay" | "y" -> "Yankee" | "z" -> "Zulu" | element -> "Unknown" Quite simple, an element is passed in, this element is them converted to a lowercase single character string and then matched up with the equivalent word. If by some chance a character is not recognized, “Unknown” will be returned… I know need a function that can take a string and can parse each character of the string and generate a new sequence with the converted words… let ConvertCharsToStrings (s:string) = s |> Seq.toArray |> Seq.map(fun elem -> CharToString(elem)) Here… the Seq.toArray converts the string to a sequence of characters. I then searched for some way to parse through every element in the sequence. Originally I tried Seq.iter, but I think my understanding of what iter does was incorrect. Eventually I found Seq.map, which applies a function to every element in a sequence and then creates a new collection with the adjusted processed element. It turned out to be exactly what I needed… To test that everything worked I created one more function that parsed through every element in a sequence and printed it. AT this point I realized the the Seq.iter would be ideal for this… So my testing code is below… let PrintStrings items = items |> Seq.iter(fun x -> Console.Write(x.ToString() + " ")) let newSeq = ConvertCharsToStrings("acdefg123") PrintStrings newSeq Console.ReadLine() Pretty basic stuff I guess… I hope my approach was right? In Part 2 I will look into doing a simple Silverlight Frontend, referencing the projects together and deploying….

Read the article

Driver error when using multiple shaders

- by Jinxi

I'm using 3 different shaders: a tessellation shader to use the tessellation feature of DirectX11 :) a regular shader to show how it would look without tessellation and a text shader to display debug-info such as FPS, model count etc. All of these shaders are initialized at the beginning. Using the keyboard, I can switch between the tessellation shader and regular shader to render the scene. Additionally, I also want to be able toggle the display of debug-info using the text shader. Since implementing the tessellation shader the text shader doesn't work anymore. When I activate the DebugText (rendered using the text-shader) my screens go black for a while, and Windows displays the following message: Display Driver stopped responding and has recovered This happens with either of the two shaders used to render the scene. Additionally: I can start the application using the regular shader to render the scene and then switch to the tessellation shader. If I try to switch back to the regular shader I get the same error as with the text shader. What am I doing wrong when switching between shaders? What am I doing wrong when displaying text at the same time? What file can I post to help you help me? :) thx P.S. I already checked if my keyinputs interrupt at the wrong time (during render or so..), but that seems to be ok Testing Procedure Regular Shader without text shader Add text shader to Regular Shader by keyinput (works now, I built the text shader back to only vertex and pixel shader) (somthing with the z buffer is stil wrong...) Remove text shader, then change shader to Tessellation Shader by key input Then if I add the Text Shader or switch back to the Regular Shader Switching/Render Shader Here the code snipet from the Renderer.cpp where I choose the Shader according to the boolean "m_useTessellationShader": if(m_useTessellationShader) { // Render the model using the tesselation shader ecResult = m_ShaderManager->renderTessellationShader(m_D3D->getDeviceContext(), meshes[lod_level]->getIndexCount(), worldMatrix, viewMatrix, projectionMatrix, textures, texturecount, m_Light->getDirection(), m_Light->getAmbientColor(), m_Light->getDiffuseColor(), (D3DXVECTOR3)m_Camera->getPosition(), TESSELLATION_AMOUNT); } else { // todo: loaded model depends on distance to camera // Render the model using the light shader. ecResult = m_ShaderManager->renderShader(m_D3D->getDeviceContext(), meshes[lod_level]->getIndexCount(), lod_level, textures, texturecount, m_Light->getDirection(), m_Light->getAmbientColor(), m_Light->getDiffuseColor(), worldMatrix, viewMatrix, projectionMatrix); } And here the code snipet from the Mesh.cpp where I choose the Typology according to the boolean "useTessellationShader": // RenderBuffers is called from the Render function. The purpose of this function is to set the vertex buffer and index buffer as active on the input assembler in the GPU. Once the GPU has an active vertex buffer it can then use the shader to render that buffer. void Mesh::renderBuffers(ID3D11DeviceContext* deviceContext, bool useTessellationShader) { unsigned int stride; unsigned int offset; // Set vertex buffer stride and offset. stride = sizeof(VertexType); offset = 0; // Set the vertex buffer to active in the input assembler so it can be rendered. deviceContext->IASetVertexBuffers(0, 1, &m_vertexBuffer, &stride, &offset); // Set the index buffer to active in the input assembler so it can be rendered. deviceContext->IASetIndexBuffer(m_indexBuffer, DXGI_FORMAT_R32_UINT, 0); // Check which Shader is used to set the appropriate Topology // Set the type of primitive that should be rendered from this vertex buffer, in this case triangles. if(useTessellationShader) { deviceContext->IASetPrimitiveTopology(D3D11_PRIMITIVE_TOPOLOGY_3_CONTROL_POINT_PATCHLIST); }else{ deviceContext->IASetPrimitiveTopology(D3D11_PRIMITIVE_TOPOLOGY_TRIANGLELIST); } return; } RenderShader Could there be a problem using sometimes only vertex and pixel shader and after switching using vertex, hull, domain and pixel shader? Here a little overview of my architecture: TextClass: uses font.vs and font.ps deviceContext-VSSetShader(m_vertexShader, NULL, 0); deviceContext-PSSetShader(m_pixelShader, NULL, 0); deviceContext-PSSetSamplers(0, 1, &m_sampleState); RegularShader: uses vertex.vs and pixel.ps deviceContext-VSSetShader(m_vertexShader, NULL, 0); deviceContext-PSSetShader(m_pixelShader, NULL, 0); deviceContext-PSSetSamplers(0, 1, &m_sampleState); TessellationShader: uses tessellation.vs, tessellation.hs, tessellation.ds, tessellation.ps deviceContext-VSSetShader(m_vertexShader, NULL, 0); deviceContext-HSSetShader(m_hullShader, NULL, 0); deviceContext-DSSetShader(m_domainShader, NULL, 0); deviceContext-PSSetShader(m_pixelShader, NULL, 0); deviceContext-PSSetSamplers(0, 1, &m_sampleState); ClearState I'd like to switch between 2 shaders and it seems they have different context parameters, right? In clearstate methode it says it resets following params to NULL: I found following in my Direct3D Class: depth-stencil state - m_deviceContext-OMSetDepthStencilState rasterizer state - m_deviceContext-RSSetState(m_rasterState); blend state - m_device-CreateBlendState viewports - m_deviceContext-RSSetViewports(1, &viewport); I found following in every Shader Class: input/output resource slots - deviceContext-PSSetShaderResources shaders - deviceContext-VSSetShader to - deviceContext-PSSetShader input layouts - device-CreateInputLayout sampler state - device-CreateSamplerState These two I didn't understand, where can I find them? predications - ? scissor rectangles - ? Do I need to store them all localy so I can switch between them, because it doesn't feel right to reinitialize the Direct3d and the Shaders by every switch (key input)?!

Read the article

MSSQL: Copying data from one database to another

- by DigiMortal

I have database that has data imported from another server using import and export wizard of SQL Server Management Studio. There is also empty database with same tables but it also has primary keys, foreign keys and indexes. How to get data from first database to another? Here is the description of my crusade. And believe me – it is not nice one. Bugs in import and export wizard There is some awful bugs in import and export wizard that makes data imports and exports possible only on very limited manner: wizard is not able to analyze foreign keys, wizard wants to create tables always, whatever you say in settings. The result is faulty and useless package. Now let’s go step by step and make things work in our scenario. Database There are two databases. Let’s name them like this: PLAIN – contains data imported from remote server (no indexes, no keys, no nothing, just plain dumb data) CORRECT – empty database with same structure as remote database (indexes, keys and everything else but no data) Our goal is to get data from PLAIN to CORRECT. 1. Create import and export package In this point we will create faulty SSIS package using SQL Server Management Studio. Run import and export wizard and let it create SSIS package that reads data from CORRECT and writes it to, let’s say, CORRECT-2. Make sure you enable identity insert. Make sure there are no views selected. Make sure you don’t let package to create tables (you can miss this step because it wants to create tables anyway). Save package to SSIS. 2. Modify import and export package Now let’s clean up the package and remove all faulty crap. Connect SQL Server Management Studio to SSIS instance. Select the package you just saved and export it to your hard disc. Run Business Intelligence Studio. Create new SSIS project (DON’T MISS THIS STEP). Add package from disc as existing item to project and open it. Move to Control Flow page do one of following: Remove all preparation SQL-tasks and connect Data Flow tasks. Modify all preparation SQL-tasks so the existence of tables is checked before table is created (yes, you have to do it manually). Add new Execute-SQL task as first task in control flow: Open task properties. Assign destination connection as connection to use. Insert the following SQL as command: EXEC sp_MSForEachTable 'ALTER TABLE ? NOCHECK CONSTRAINT ALL' GO EXEC sp_MSForEachTable 'DELETE FROM ?' GO Save task. Add new Execute-SQL task as last task in control flow: Open task properties. Assign destination connection as connection to use. Insert the following SQL as command: EXEC sp_MSForEachTable 'ALTER TABLE ? CHECK CONSTRAINT ALL' GO Save task Now connect first Execute-SQL task with first Data Flow task and last Data Flow task with second Execute-SQL task. Now move to Package Explorer tab and change connections under Connection Managers folder. Make source connection to use database PLAIN. Make destination connection to use database CORRECT. Save package and rebuilt the project. Update package using SQL Server Management Studio. Some hints: Make sure you take the package from solution folder because it is saved there now. Don’t overwrite existing package. Use numeric suffix and let Management Studio to create a new version of package. Now you are done with your package. Run it to test it and clean out all the errors you find. TRUNCATE vs DELETE You can see that I used DELETE FROM instead of TRUNCATE. Why? Because TRUNCATE has some nasty limits (taken from MSDN): “You cannot use TRUNCATE TABLE on a table referenced by a FOREIGN KEY constraint; instead, use DELETE statement without a WHERE clause. Because TRUNCATE TABLE is not logged, it cannot activate a trigger. TRUNCATE TABLE may not be used on tables participating in an indexed view.” As I am not sure what tables you have and how they are used I provided here the solution that should work for all scenarios. If you need better performance then in some cases you can use TRUNCATE table instead of DELETE. Conclusion My conclusion is bitter this time although I am very positive guy. It is A.D. 2010 and still we have to write stupid hacks for simple things. Simple tools that existed before are long gone and we have to live mysterious bloatware that is our only choice when using default tools. If you take a look at the length of this posting and the count of steps I had to do for one easy thing you should treat it as a signal that something has went wrong in last years. Although I got my job done I would be still more happy if out of box tools are more intelligent one day. References T-SQL Trick for Deleting All Data in Your Database (Mauro Cardarelli) TRUNCATE TABLE (MSDN Library) Error Handling in SQL 2000 – a Background (Erland Sommarskog) Disable/Enable Foreign Key and Check constraints in SQL Server (Decipher)

Read the article

How do I turn on wireless adapter on HP Envy dv6 7200 under Ubuntu (any version)?

- by Dave B.

I have a new HP Envy dv6 7200 with dual boot Windows 8 / Ubuntu 12.04. In windows, the F12 key in Windows activates the "airplane mode" switch which enables/disables both on-board (mini PCIe) and USB wireless adapters. In Ubuntu, however, the wireless adapter is turned off by default and cannot be turned back on via the F12 key (or any other combination of F12 and Ctrl, Fn, Shift, etc.). Let me explain the "fixes" I've seen in various forums and explain what did or did not happen. These are listed in no particular order. (Spoiler alert: wireless is still broke). Solution 1? Use HP's "Wireless Assistant" utility to permanently activate the wireless card in Windows, then boot into Ubuntu to happily find it working. Unfortunately, this utility works in Windows 7 but not Windows 8. On the other hand, hardware drivers from HP are only available for Windows 8 for this model. Catch 22 (I could not find a comparable utility for Windows 8). Solution 2? Use a USB wireless adapter to sidestep the on-board device. I purchased such a device from thinkpenguin.com to be sure that it would be Linux-friendly. However, the wireless switch enables / disables all wireless devices including USB. So, there's my $50 donation to the nice folks at thinkpenguin.com, but still no solution. Solution 3? Following the Think Penguin folk's suggestion, modify the mini PCI express adapter following instructions here: http://www.notebookforums.com/t/225429/broken-wireless-hardware-switch-fix Tempting, but I then violate the terms of my warranty mere days after opening the box. This might be a good solution for an older machine that you want to get your geek on with, but not for a new box. Solution 4? rfkill unblock all No effect whatsoever. ubuntu@ubuntu-hp-evny:~$ rfkill unblock all ubuntu@ubuntu-hp-evny:~$ rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Solution 5? Re-install drivers. Done and done. Ubuntu recognizes the device - perhaps even without re-installing the drivers? - but cannot turn it on. How do I know this? In the Network Manager drop-down menu, the wireless option is blacked out and a message reads something like: "wireless network is disabled by a hardware switch". Solution 6? Identify a physical switch on the laptop and flip it. There is no such switch on this machine. In fact, walking through Best Buy yesterday, I checked and not a single new laptop PC had a physical switch on it. All of the wireless switches are either the F2 or F12 key ... I wonder if askubuntu will not be plagued by this exact issue in the near future? Additional info - lspci ubuntu@ubuntu-hp-evny:~$ lspci 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01) 0a:00.0 Network controller: Ralink corp. Device 539b 0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Any suggestions would be much appreciated!

Read the article

Caveat utilitor - Can I run two versions of Microsoft Project side-by-side?

- by Martin Hinshelwood

A number of out customers have asked if there are any problems in installing and running multiple versions of Microsoft Project on a single client. Although this is a case of Caveat utilitor (Let the user beware), as long as the user understands and accepts the issues that can occur then they can do this. Although Microsoft provide the ability to leave old versions of Office products (except Outlook) on your client when you are installing a new version of the product they certainly do not endorse doing so. Figure: For Project you can choose to keep the old stuff That being the case I would have preferred that they put a “(NOT RECOMMENDED)” after the options to impart that knowledge to the rest of us, but they did not. The default and recommended behaviour is for the newer version installer to remove the older versions. Of course this does not apply in the revers. There are no forward compatibility packs for Office. There are a number of negative behaviours (or bugs) that can occur in this configuration: There is only one MS Project In Windows a file extension can only be associated with a single program. In this case, MPP files can be associated with only one version of winproj.exe. The executables are in different folders so if a user double-clicks a Project file on the desktop, file explorer, or Outlook email, Windows will launch the winproj.exe associated with MPP and then load the MPP file. There are problems associated with this situation and in some cases workarounds. The user double-clicks on a Project 2010 file, Project 2007 launches but is unable to open the file because it is a newer version. The workaround is for the user to launch Project 2010 from the Start menu then open the file. If the file is attached to an email they will need to first drag the file to the desktop. All your linked MS Project files need to be of the same version There are a number of problems that occur when people use on Microsoft’s Object Linking and Embedding (OLE) technology. The three common uses of OLE are: for inserted projects where a Master project contains sub-projects and each sub-project resides in its own MPP file shared resource pools where multiple MPP files share a common resource pool kept in a single MPP file cross-project links where a task or milestone in one MPP file has a predecessor/successor relationship with a task or milestone in a different MPP file What I’ve seen happen before is that if you are running in a version of Project that is not associated with the MPP extension and then try and activate an OLE link then Project tries to launch the other version of Project. Things start getting very confused since different MPP files are being controlled by different versions of Project running at the same time. I haven’t tried this in awhile so I can’t give you exact symptoms but I suspect that if Project 2010 is involved the symptoms will be different then in a Project 2003/2007 scenario. I’ve noticed that Project 2010 gives different error messages for the exact same problem when it occurs in Project 2003 or 2007. -Anonymous The recommendation would be either not to use this feature if you have to have multiple versions of Project installed or to use only a single version of Project. You may get unexpected negative behaviours if you are using shared resource pools or resource pools even when you are not running multiple versions as I have found that they can get broken very easily. If you need these thing then it is probably best to use Project Server as it was created to solve many of these specific issues. Note: I would not even allow multiple people to access a network copy of a Project file because of the way Windows locks files in write mode. This can cause write-locks that get so bad a server restart is required I’ve seen user’s files get write-locked to the point where the only resolution is to reboot the server. Changing the default version to run for an extension So what if you want to change the default association from Project 2007 to Project 2010? Figure: “Control Panel | Folder Options | Change the file associated with a file extension” Windows normally only lists the last version installed for a particular extension. You can select a specific version by selecting the program you want to change and clicking “Change program… | Browse…” and then selecting the .exe you want to use on the file system. Figure: You will need to select the exact version of “winproj.exe” that you want to run Conclusion Although it is possible to run multiple versions of Project on one system in the main it does not really make sense.

Read the article

Creating the Business Card Request InfoPath Form

- by JKenderdine

Business Card Request Demo Files Back in January I spoke at SharePoint Saturday Virginia Beach about InfoPath forms and Web Part deployment. Below is some of the information and details regarding the form I created for the session. There are many blogs and Microsoft articles on how to create a basic form so I won’t repeat that information here. This blog will just explain a few of the options I chose when creating the solutions for SPS Virginia Beach. The above link contains the zipped package files of the two InfoPath forms(no code solution and coded solution), the list template for the Location list I used, and the PowerPoint deck. If you plan to use these templates, you will need to update the forms to work within your own environments (change data connections, code links, etc.). Also, you must have the SharePoint Enterprise version, with InfoPath Services configured in order to use the Web Browser enabled forms. So what are the requirements for this template? Business Card Request Form Template Design Plan: Gather user information and requirements for card Pull in as much user information as possible. Use data from the user profile web services as a data source Show and hide fields as necessary for requirements Create multiple views – one for those submitting the form and Another view for the executive assistants placing the orders. Browser based form integrated into SharePoint team site Submitted directly to form library The base form was created using the blank template. The table and rows were added using Insert tab and selecting Custom Table. The use of tables is a great way to make sure everything lines up. You do have to split the tables from time to time. If you’ve ever split cells and then tried to re-align one to find that you impacted the others, you know why. Here is what the base form looks like in InfoPath. Show and hide fields as necessary for requirements You will notice I also used Sections within the form. These show or hide depending on options selected or whether or not fields are blank. This is a great way to prevent your users from feeling overwhelmed with a large form (this one wouldn’t apply). Although not used in this one, you can also use various views with a tab interface. I’ll show that in another post. Gather user information and requirements for card Pull in as much user information as possible. Use data from the user profile web services as a data source Utilizing rules you can load data when the form initiates (Data tab, Form Load). Anything you can automate is always appreciated by the user as that is data they don’t have to enter. For example, loading their user id or other user information on load: Always keep in mind though how much data you load and the method for loading that data (through rules, code, etc.). They have an impact on form performance. The form will take longer to load if you bring in a ton of data from external sources. Laura Rogers has a great blog post on using the User Information List to load user information. If the user has logged into SharePoint, then this can be used quite effectively and without a huge performance hit. What I have found is that using the User Profile service via code behind or the Web Service “GetUserProfileByName” (as above) can take more time to load the user data. Just food for thought. You must add the data connection in order for the above rules to work. You can connect to the data connection through the Data tab, Data Connections or select Manage Data Connections link which appears under the main data source. The data connections can be SharePoint lists or libraries, SQL data tables, XML files, etc. Create multiple views – one for those submitting the form and Another view for the executive assistants placing the orders. You can also create multiple views for the users to enhance their experience. Once they’ve entered the information and submitted their request for business cards, they don’t really need to see the main data input screen any more. They just need to view what they entered. From the Page Design tab, select New View and give the view a name. To review the existing views, click the down arrow under View: The ReviewView shows just what the user needs and nothing more: Once you have everything configured, the form should be tested within a Test SharePoint environment before final deployment to production. This validates you don’t have any rules or code that could impact the server negatively. Submitted directly to form library You will need to know the form library that you will be submitting to when publishing the template. Configure the Submit data connection to connect to this library. There is already one configured in the sample, but it will need to be updated to your environment prior to publishing. The Design template is different from the Published template. While both have the .XSN extension, the published template contains all the “package” information for the form. The published form is what is loaded into Central Admin, not the design template. Browser based form integrated into SharePoint team site In Central Admin, under General Settings, select Manage Form Templates. Upload the published form template and Activate it to a site collection. Now it is available as a content type to select in the form library. Some documentation on publishing form templates: Technet – Manage administrator approved form templates And that’s all our base requirements. Hope this helps to give a good start.

Read the article

Updating a database connection password using a script

- by Tim Dexter

An interesting customer requirement that I thought was worthy of sharing today. Thanks to James for the requirement and Bryan for the proposed solution and me for testing the solution and proving it works :0) A customers implementation of Sarbanes Oxley requires them to change all database account passwords every 90 days. This is scripted leveraging shell scripts today for most of their environments. But how can they manage the BI Publisher connections? Now, the customer is running 11g and therefore using weblogic on the middle tier, which is the first clue to Bryans proposed solution. To paraphrase and embellish Bryan's solution a little; why not use a JNDI connection from BIP to the database. Then employ the web logic scripting engine to make updates to the JNDI as needed? BIP is completely uninvolved and with a little 'timing' users will be completely unaware of the password updates i.e. change the password when reports are not being executed. Perfect! James immediately tracked down the WLST script that could be used here, http://middlewaremagic.com/weblogic/?p=4261 (thanks Ravish) Now it was just a case of testing the theory. Some steps: Create the JNDI connection in WLS Create the JNDI connection in BI Publisher pointing to the WLS connection Build new data models using or re-point data sources to use the JNDI connection. Create the WLST script to update the WLS JNDI password as needed. Test! Some details. Creating the JNDI connection in web logic is pretty straightforward. Log into hte console and look for Data Sources under the Services section of the home page and click it Click New >> Generic Datasource Give the connection a name. For the JNDI name, prefix it with 'jdbc/' so I have 'jdbc/localdb' - this name is important you'll need it on the BIP side. Select your db type - this will influence the drivers and information needed on the next page. Being a company man, Im using an Oracle db. Click Next Select the driver of choice, theres lots I know, you can read about them I just chose 'Oracle's Driver (Thin) for Instance connections; Versions 9.0.1 and later' Click Next >> Next Fill out the db name (SID), server, port, username to connect and password >> Next Test the config to ensure you can connect. >> Next Now you need to deploy the connection to your BI server, select it and click Next. You're done with the JNDI config. Creating the JNDI connection on the Publisher side is covered here. Just remember to the connection name you created in WLS e.g. 'jdbc/localdb' Not gonna tell you how to do this, go read the user guide :0) Suffice to say, it works. This requires a little reading around the subject to understand the scripting engine and how to execute scripts. Nicely covered here. However a bit of googlin' and I found an even easier way of running the script. ${ServerHome}/common/bin/wlst.sh updatepwd.py Where updatepwd.py is my script file, it can be in another directory. As part of the wlst.sh script your environment is set up for you so its very simple to execute. The nitty gritty: Need to take Ravish's script above and create a file with a .py extension. Its going to need some modification, as he explains on the web page, to make it work in your environment. I played around with it for a while but kept running into errors. The script as is, tries to loop through all of your connections and modify the user and passwords for each. Not quite what we are looking for. Remember our requirement is to just update the password for a given connection. I also found another issue with the script. WLS 10.x does not allow updates to passwords using clear type ie un-encrypted text while the server is in production mode. Its a bit much to set it back to developer mode bounce it, change the passwords and then bounce and then change back to production and bounce again. After lots of messing about I finally came up with the following: ############################################################################# # # Update password for JNDI connections # ############################################################################# print("*** Trying to Connect.... *****") connect('weblogic','welcome1','t3://localhost:7001') print("*** Connected *****") edit() startEdit() print ("*** Encrypt the password ***") en = encrypt('hr') print "Encrypted pwd: ", en print ("*** Changing pwd for LocalDB ***") dsName = 'LocalDB' print 'Changing Password for DataSource ', dsName cd('/JDBCSystemResources/'+dsName+'/JDBCResource/'+dsName+'/JDBCDriverParams/'+dsName) set('PasswordEncrypted',en) save() activate() Its pretty simple and you can expand on it to loop through the data sources and change each as needed. I have hardcoded the password into the file but you can pass it as a parameter as needed using the properties file method. Im not going to get into the detail of that here but its covered with an example here. Couple of points to note: 1. The change to the password requires a server bounce to get the changes picked up. You can add that to the shell script you will use to call the script above. 2. The script above needs to be run from the MW_HOME\user_projects\domains\bifoundation_domain directory to get the encryption libraries set correctly. My command to run the whole script was: d:\oracle\bi_mw\wlserver_10.3\common\bin\wlst.cmd updatepwd.py - where wlst.cmd is the scripting command line and updatepwd.py was my update password script above. I have not quite spoon fed everything you need to make it a robust script but at least you know you can do it and you can work out the rest I think :0)

Read the article

GameplayScreen does not contain a definition for GraphicsDevice

- by Dave Voyles

Long story short: I'm trying to intergrate my game with Microsoft's Game State Management. In doing so I've run into some errors, and the latest one is in the title. I'm not able to display my HUD for the reasons listed above. Previously, I had much of my code in my Game.cs class, but the GSM has a bit of it in Game1, and most of what you have drawn for the main screen in your GameplayScreen class, and that is what is causing confusion on my part. I've created an instance of the GameplayScreen class to be used in the HUD class (as you can see below). Before integrating with the GSM however, I created an instance of my Game class, and all worked fine. It seems that I need to define my graphics device somewhere, but I am not sure of where exactly. I've left some code below to help you understand. public class GameStateManagementGame : Microsoft.Xna.Framework.Game { #region Fields GraphicsDeviceManager graphics; ScreenManager screenManager; // Creates a new intance, which is used in the HUD class public static Game Instance; // By preloading any assets used by UI rendering, we avoid framerate glitches // when they suddenly need to be loaded in the middle of a menu transition. static readonly string[] preloadAssets = { "gradient", }; #endregion #region Initialization /// <summary> /// The main game constructor. /// </summary> public GameStateManagementGame() { Content.RootDirectory = "Content"; graphics = new GraphicsDeviceManager(this); graphics.PreferredBackBufferWidth = 1280; graphics.PreferredBackBufferHeight = 720; graphics.IsFullScreen = false; graphics.ApplyChanges(); // Create the screen manager component. screenManager = new ScreenManager(this); Components.Add(screenManager); // Activate the first screens. screenManager.AddScreen(new BackgroundScreen(), null); //screenManager.AddScreen(new MainMenuScreen(), null); screenManager.AddScreen(new PressStartScreen(), null); } namespace Pong { public class HUD { public void Update(GameTime gameTime) { // Used in the Draw method titleSafeRectangle = new Rectangle (GameplayScreen.Instance.GraphicsDevice.Viewport.TitleSafeArea.X, GameplayScreen.Instance.GraphicsDevice.Viewport.TitleSafeArea.Y, GameplayScreen.Instance.GraphicsDevice.Viewport.TitleSafeArea.Width, GameplayScreen.Instance.GraphicsDevice.Viewport.TitleSafeArea.Height); } } } class GameplayScreen : GameScreen { #region Fields ContentManager content; public static GameStates gamestate; private GraphicsDeviceManager graphics; public int screenWidth; public int screenHeight; private Texture2D backgroundTexture; private SpriteBatch spriteBatch; private Menu menu; private SpriteFont arial; private HUD hud; Animation player; // Creates a new intance, which is used in the HUD class public static GameplayScreen Instance; public GameplayScreen() { TransitionOnTime = TimeSpan.FromSeconds(1.5); TransitionOffTime = TimeSpan.FromSeconds(0.5); } protected void Initialize() { lastScored = false; menu = new Menu(); resetTimer = 0; resetTimerInUse = true; ball = new Ball(content, new Vector2(screenWidth, screenHeight)); SetUpMulti(); input = new Input(); hud = new HUD(); // Places the powerup animation inside of the surrounding box // Needs to be cleaned up, instead of using hard pixel values player = new Animation(content.Load<Texture2D>(@"gfx/powerupSpriteSheet"), new Vector2(103, 44), 64, 64, 4, 5); // Used by for the Powerups random = new Random(); vec = new Vector2(100, 50); vec2 = new Vector2(100, 100); promptVec = new Vector2(50, 25); timer = 10000.0f; // Starting value for the cooldown for the powerup timer timerVector = new Vector2(10, 10); //JEP - one time creation of powerup objects playerOnePowerup = new Powerup(); playerOnePowerup.Activated += PowerupActivated; playerOnePowerup.Deactivated += PowerupDeactivated; playerTwoPowerup = new Powerup(); playerTwoPowerup.Activated += PowerupActivated; playerTwoPowerup.Deactivated += PowerupDeactivated; //JEP - moved from events since these only need set once activatedVec = new Vector2(100, 125); deactivatedVec = new Vector2(100, 150); powerupReady = false; }

Read the article

In Social Relationship Management, the Spirit is Willing, but Execution is Weak

- by Mike Stiles

In our final talk in this series with Aberdeen’s Trip Kucera, we wanted to find out if enterprise organizations are actually doing anything about what they’re learning around the importance of communicating via social and using social listening for a deeper understanding of customers and prospects. We found out that if your brand is lagging behind, you’re not alone. Spotlight: How was Aberdeen able to find out if companies are putting their money where their mouth is when it comes to implementing social across the enterprise? Trip: One way to think about the relative challenges a business has in a given area is to look at the gap between “say” and “do.” The first of those words reveals the brand’s priorities, while the second reveals their ability to execute on those priorities. In Aberdeen’s research, we capture this by asking firms to rank the value of a set of activities from one on the low end to five on the high end. We then ask them to rank their ability to execute those same activities, again on a one to five, not effective to highly effective scale. Spotlight: And once you get their self-assessments, what is it you’re looking for? Trip: There are two things we’re looking for in this analysis. The first is we want to be able to identify the widest gaps between perception of value and execution. This suggests impediments to adoption or simply a high level of challenge, be it technical or otherwise. It may also suggest areas where we can expect future investment and innovation. Spotlight: So the biggest potential pain points surface, places where they know something is critical but also know they aren’t doing much about it. What’s the second thing you look for? Trip: The second thing we want to do is look at specific areas in which high-performing companies, the Leaders, are out-executing the Followers. This points to the business impact of these activities since Leaders are defined by a set of business performance metrics. Put another way, we’re correlating adoption of specific business competencies with performance, looking for what high-performers do differently. Spotlight: Ah ha, that tells us what steps the winners are taking that are making them winners. So what did you find out? Trip: Generally speaking, we see something of a glass curtain when it comes to the social relationship management execution gap. There isn’t a single social media activity in which more than 50% of respondents indicated effectiveness, which would be a 4 or 5 on that 1-5 scale. This despite the fact that 70% of firms indicate that generating positive social media mentions is valuable or very valuable, a 4 or 5 on our 1-5 scale. Spotlight: Well at least they get points for being honest. The verdict they’re giving themselves is that they just aren’t cutting it in these highly critical social development areas. Trip: And the widest gap is around directly engaging with customers and/or prospects on social networks, which 69% of firms rated as valuable but only 34% of companies say they are executing well. Perhaps even more interesting is that these two are interdependent since you’re most likely to generate goodwill on social through happy, engaged customers. This data also suggests that social is largely being used as a broadcast channel rather than for one-to-one engagement. As we’ve discussed previously, social is an inherently personal media. Spotlight: And if they’re still using it as a broadcast channel, that shows they still fail to understand the root of social and see it as just another outlet for their ads and push-messaging. That’s depressing. Trip: A second way to evaluate this data is by using Aberdeen’s performance benchmarking. The story is both a bit different, but consistent in its own way. The first thing we notice is that Leaders are more effective in their execution of several key social relationship management capabilities, namely generating positive mentions and engaging with “influencers” and customers. Based on the fact that Aberdeen uses a broad set of performance metrics to rank the respondents as either “Leaders” (top 35% in weighted performance) or “Followers” (bottom 65% in weighted performance), from website conversion to annual revenue growth, we can then correlated high social effectiveness with company performance. We can also connect the specific social capabilities used by Leaders with effectiveness. We spoke about a few of those key capabilities last time and also discuss them in a new report: Social Powers Activate: Engineering Social Engagement to Win the Hidden Sales Cycle. Spotlight: What all that tells me is there are rewards for making the effort and getting it right. That’s how you become a Leader. Trip: But there’s another part of the story, which is that overall effectiveness, even among Leaders, is muted. There’s just one activity in which more than a majority of Leaders cite high effectiveness, effectiveness being the generation of positive buzz. While 80% of Leaders indicate “directly engaging with customers” through social media channels is valuable, the highest rated activity among Leaders, only 42% say they’re effective. This gap even among Leaders shows the challenges still involved in effective social relationship management. @mikestilesPhoto: stock.xchng

Read the article

Training a 'replacement', how to enforce standards?

- by Mohgeroth

Not sure that this is the right stack exchange site to ask this of, but here goes... Scope I work for a small company that employs a few hundred people. The development team for the company is small and works out of visual foxpro. A specific department in the company hired me in as a 'lone gunman' to fix and enhance a pre-existing invoicing system. I've successfully taken an Access application that suffered from a lot of risks and limitations and converted it into a C# application driven off of a SQL server backend. I have recently obtained my undergraduate and am no expert by any means. To help make up for that I've felt that earning microsoft certifications will force me to understand more about .net and how it functions. So, after giving my notice with 9 months in advance, 3 months ago a replacement finally showed up. Their role is to learn what I have been designing to an attempt to support the applications designed in C#. The Replacement Fresh out of college with no real-world work experience, the first instinct for anything involving data was and still is listboxes... any time data is mentioned the list box is the control of choice for the replacement. This has gotten to the point, no matter how many times I discuss other controls, where I've seen 5 listboxes on a single form. Classroom experience was almost all C++ console development. So, an example of where I have concern is in a winforms application: Users need to key Reasons into a table to select from later. Given that I know that a strongly typed data set exists, I can just drag the data source from the toolbox and it would create all of this for me. I realize this is a simple example but using databinding is the key. For the past few months now we have been talking about the strongly typed dataset, how to use it and where it interacts with other controls. Data sets, how they work in relation to binding sources, adapters and data grid views. After handing this project off I expected questions about how to implement these since for me this is the way to do it. What happened next simply floors me: An instance of an adapter from the strongly typed dataset was created in the activate event of the form, a table was created and filled with data. Then, a loop was made to manually add rows to a listbox from this table. Finally, a variable was kept to do lookups to figure out what ID the record was for updates if required. How do they modify records you ask? That was my first question too. You won't believe how simple it is, all you do it double click and they type into a pop-up prompt the new value to change it to. As a data entry operator, all the modal popups would drive me absolutely insane. The final solution exceeds 100 lines of code that must be maintained. So my concern is that none of this is sinking in... the department is only allowed 20 hours a week of their time. Up until last week, we've only been given 4-5 hours a week if I'm lucky. The past week or so, I've been lucky to get 10. Question WHAT DO I DO?! I have 4 weeks left until I leave and they fully 'support' this application. I love this job and the opportunity it has given me but it's time for me to spread my wings and find something new. I am in no way, shape or form convinced that they are ready to take over. I do feel that the replacement has the technical ability to 'figure it out' but instead of learning they just write code to do all of this stuff manually. If the replacement wants to code differently in the end, as long as it works I'm fine with that as horrifiying at it looks. However to support what I have designed they MUST to understand how it works and how I have used controls and the framework to make 'magic' happen. This project has about 40 forms, a database with over 30 some odd tables, triggers and stored procedures. It relates labor to invoices to contracts to projections... it's not as simple as it was three years ago when I began this project and the department is now in a position where they cannot survive without it. How in the world can I accomplish any of the following?: Enforce standards or understanding in constent design when the department manager keeps telling them they can do it however they want to Find a way to engage the replacement in active learning of the framework and system design that support must be given for Gracefully inform sr. management that 5-9 hours a week is simply not enough time to learn about the department, pre-existing processes, applications that need to be supported AND determine where potential enhancements to the system go... Yes I know this is a wall of text, thanks for reading through me but I simply don't know what I should be doing. For me, this job is a monster of a reference and things would look extremely bad if I left and things fell apart. How do I handle this?

Read the article

Cookbook: SES and UCM setup

- by George Maggessy

The purpose of this post is to guide you setting up the integration between UCM and SES. On my next post I’ll show different approaches to integrate WebCenter Portal, UCM and SES based on some common scenarios. Let’s get started. WebCenter Content Configuration WebCenter Content has a component that adds functionality to the content server to allow it to be searched via the Oracle SES. To enable the component installation, go to Administration -> Admin Server and select SESCrawlerExport. Click the update button and restart UCM_server1 managed server. Once the managed server is back, we’ll configure the component. In the menu, under Administration you should see SESCrawlerExport. Click on the link. You’ll see the window below. Click on Configure SESCrawlerExport. Configure the values below: Hostname: SES hostname. Feed Location: Directory where data feeds will be saved. Metadata List: List of metadata that will be searchable by SES. After updating the values click on the Update button. Come back to the SESCrawlerExport Administration UI and click on Take Snapshot button. It will create the data feeds in the specified Feed Location. To check if the correct configuration was done, please access the following URL http://<ucm_server>:<port>/cs/idcplg?IdcService=SES_CRAWLER_DOWLOAD_CONFIG&source=default. It should download config file in the format below: <?xml version="1.0" encoding="UTF-8"?> <rsscrawler xmlns="http://xmlns.oracle.com/search/rsscrawlerconfig"> <feedLocation><![CDATA[http://adc6160699.us.oracle.com:16200/cs/idcplg?IdcService=SES_CRAWLER_DOWNLOAD_CONTROL&source=default]]></feedLocation> <errorFileLocation><![CDATA[http://adc6160699.us.oracle.com:16200/cs/idcplg?IdcService=SES_CRAWLER_STATUS&IsJava=1&source=default&StatusFeed=]]></errorFileLocation> <feedType>controlFeed</feedType> <sourceName>default</sourceName> <securityType>attributeBased</securityType> <securityAttribute name="Account" grant="true"/> <securityAttribute name="DocSecurityGroup" grant="true"/> <securityAttribute name="Collab" grant="true"/> </rsscrawler> Make sure Account and DocSecurityGroup values are true. SES Configuration Let’s start by configuring the Identity Plug-ins in SES. Go to Global Settings -> System -> Identity Management Setup. Select Oracle Content Server and click the Activate button. We’ll populate the following values: HTTP endpoint for authentication: URL to WebCenter Content. Notice that /cs/idcplg was added at the end of the URL. Admin User: UCM Admin user. This user must have access to all CPOE content. Password: Password to Admin user. Authentication Type: NATIVE. Go back to the Home tab and click on Sources on the top left. Select Oracle Content Server on the right and click the Create button. Configuration URL: URL that point to the configuration file. Example: http://<ucm_hostname>:<port>/cs/idcplg?IdcService=SES_CRAWLER_DOWNLOAD_CONFIG&source=default. User ID: UCM Admin user. Password: Password to Admin user. Click on the Authorization tab and add the appropriate values to the fields below. Make sure you see the ACCOUNT and DOCSECURITYGROUP security attributes at the end of the page. HTTP endpoint for authorization: http://<ucm_hostname>:<port>/cs/idcplg. Display URL prefix: http://<ucm_hostname>:<port>/cs. Administrator user: UCM Admin user. Administrator password. On the Document Types tab, add the documents that should be indexed by SES. As our last step, we’ll configure the Federation Trusted Entities under Global Settings. Entity Name: The user must be present in both the identity management server configured for your WebCenter application and the identity management server configured for Oracle SES. For instance, I used weblogic in my sample. Password: Entity user password.\ Now you are ready to test the integration on the SES UI: http://<ses hostname>:<port>/search/query/.

Read the article

WSS 3.0 to SharePoint 2010: Tips for delaying the Visual Upgrade

- by Kelly Jones

My most recent project has been to migrate a bunch of sites from WSS 3.0 (SharePoint 2007) to SharePoint Server 2010. The users are currently working with WSS 3.0 and Office 2003, so the new ribbon based UI in 2010 will be completely new. My client wants to avoid the new SharePoint 2010 look and feel until they’ve had time to train their users, so we’ve been testing the upgrades by keeping them with the 2007 user interface. Permission to perform the Visual Upgrade One of the first things we noticed was the default permissions for who was allowed to switch the UI from 2007 to 2010. By default, site collection administrators and site owners can do this. Since we wanted to more tightly control the timing of the new UI, I added a few lines to the PowerShell script that we are using to perform the migration. This script creates the web application, sets the User Policy, and then does a Mount-SPDatabase to attach the old 2007 content database to the 2010 farm. I added the following steps after the Mount-SPDatabase step: #Remove the visual upgrade option for site owners # it remains for Site Collection administrators foreach ($sc in $WebApp.Sites){ foreach ($web in $sc.AllWebs){ #Visual Upgrade permissions for the site/subsite (web) $web.UIversionConfigurationEnabled = $false; $web.Update(); } } These script steps loop through each Site Collection in a particular web application ($WebApp) and then it loops through each subsite ($web) in the Site Collection ($sc) and disables the Site Owner’s permission to perform the Visual Upgrade. This is equivalent to going to the Site Collection administrator settings page –> Visual Upgrade and selecting “Hide Visual Upgrade”. Since only IT people have Site Collection administrator privileges, this will allow IT to control the timing of the new 2010 UI rollout. Newly created subsites Our next issue was brought to our attention by SharePoint Joel’s blog post last week (http://www.sharepointjoel.com/Lists/Posts/Post.aspx?ID=524 ). In it, he lists some updates about the 2010 upgrade, and his fourth point was one that I hadn’t seen yet: 4. If a 2007 upgraded site has not been visually upgraded, the sites created underneath it will look like 2010 sites – While this is something I’ve been aware of, I think many don’t realize how this impacts common look and feel for master pages, and how it impacts good navigation and UI. As well depending on your patch level you may see hanging behavior in the list picker. The site and list creation Silverlight control in Internet Explorer is looking for resources that don’t exist in the galleries in the 2007 site, and hence it continues to spin and spin and eventually time out. The work around is to upgrade to SP1, or use Chrome or Firefox which won’t attempt to render the Silverlight control. When the root site collection is a 2007 site and has it’s set of galleries and the children are 2010 sites there is some strange behavior linked to the way that the galleries work and pull from the parent. Our production SharePoint 2010 Farm has SP1 installed, as well as the December 2011 Cumulative Update, so I think the “hanging behavior” he mentions won’t affect us. However, since we want to control the roll out of the UI, we are concerned that new subsites will have the 2010 look and feel, no matter what the parent site has. Ok, time to dust off my developer skills. I first looked into using feature stapling, but I couldn’t get that to work (although I’m pretty sure I had everything wired up correctly). Then I stumbled upon SharePoint 2010’s web events – a great way to handle this. Using Visual Studio 2010, I created a new SharePoint project and added a Web Event Receiver: In the Event Receiver class, I used the WebProvisioned method to check if the parent site is a 2007 site (UIVersion = 3), and if so, then set the newly created site to 2007: /// <summary> /// A site was provisioned. /// </summary> public override void WebProvisioned(SPWebEventProperties properties) { base.WebProvisioned(properties); try { SPWeb curweb = properties.Web; if (curweb.ParentWeb != null) { //check if the parent website has the 2007 look and feel if (curweb.ParentWeb.UIVersion == 3) { //since parent site has 2007 look and feel // we'll apply that look and feel to the current web curweb.UIVersion = 3; curweb.Update(); } } } catch (Exception) { //TODO: Add logging for errors } } This event is part of a Feature that is scoped to the Site Level (Site Collection). I added a couple of lines to my migration PowerShell script to activate the Feature for any site collections that we migrate. Plan Going Forward The plan going forward is to perform the visual upgrade after the users for a particular site collection have gone through 2010 training. If we need to do several site collections at once, we’ll use a PowerShell script to loop through each site collection to update the sites to 2010. If it’s just one or two, we’ll be using the “Update All Sites” button on the Visual Upgrade page for Site Collection Administrators. The custom code for newly created sites won’t need to be changed, since it relies on the UI version of the parent site. If the parent is 2010, then the new site will look 2010.

Read the article

Migrating Virtual Iron guest to Oracle VM 3.x

- by scoter

As stated on the official site, Oracle in 2009, acquired a provider of server virtualization management software named Virtual Iron; you can find all the acquisition details at this link. Into the FAQ on the official site you can also view that, for the future, Oracle plans to fully integrate Virtual Iron technology into Oracle VM products, and any enhancements will be delivered as a part of the combined solution; this is what is going on with Oracle VM 3.x. So, customers started asking us to migrate Virtual Iron guests to Oracle VM. IMPORTANT: This procedure needs a dedicated OVM-Server with no-guests running on top; be careful while execute this procedure on production environments. In these little steps you will find how-to migrate, as fast as possible, your guests between VI ( Virtual Iron ) and Oracle VM; keep in mind that OracleVM has a built-in P2V utility ( Official Documentation ) that you can use to migrate guests between VI and Oracle VM. Concepts: VI repositories. On VI we have the same "repository" concept as in Oracle VM; the difference between these two products is that VI use a raw-lun as repository ( instead of using ocfs2 and its capabilities, like ref-links ). The VI "raw-lun" repository, with a pure operating-system perspective, may be presented as in this picture: Infact on this "raw-lun" VI create an LVM2 volume-group. The VI "raw-lun" repository, with an hypervisor perspective, may be presented as in this picture: So, the relationships are: LVM2-Volume-Group <-> VI Repository LVM2-Logical-Volume <-> VI guest virtual-disk The first step is to present the VI repository ( raw-lun ) to your dedicated OVM-Server. Prepare dedicated OVM-Server On the OVM-Server ( OVS ) you need to discover new lun and, after that, discover volume-group and logical-volumes containted in VI repository; due to default OVS configuration you need to edit lvm2 configuration file: /etc/lvm/lvm.conf # By default for OVS we restrict every block device: # filter = [ "r/.*/" ] and comment the line starting with "filter" as above. Now you have to discover the raw-lun presented and, next, activate volume-group and logical-volumes: #!/bin/bash for HOST in `ls /sys/class/scsi_host`;do echo '- - -' > /sys/class/scsi_host/$HOST/scan; done CPATH=`pwd` cd /dev for DEVICE in `ls sd[a-z] sd?[a-z]`;do echo '1' > /sys/block/$DEVICE/device/rescan; done cd $CPATH cd /dev/mapper for PARTITION in `ls *[a-z] *?[a-z]`;do partprobe /dev/mapper/$PARTITION; done cd $CPATH vgchange -a yAfter that you will see a new device:[root@ovs01 ~]# cd /dev/6000F4B00000000000210135bef64994[root@ovs01 6000F4B00000000000210135bef64994]# ls -l 6000F4B0000000000061013* lrwxrwxrwx 1 root root 77 Oct 29 10:50 6000F4B00000000000610135c3a0b8cb -> /dev/mapper/6000F4B00000000000210135bef64994-6000F4B00000000000610135c3a0b8cb By your OVM-Manager create a guest server with the same definition as on VI:same core number as VI source guestsame memory as VI source guestsame number of disks as VI source guest ( you can create OVS virtual disk with a small size of 1GB because the "clone" will, eventually, extend the size of your new virtual disks )Summarizing:source-virtual-disk path ( VI ):/dev/mapper/6000F4B00000000000210135bef64994-6000F4B00000000000610135c3a0b8cbdest-virtual-disk path ( OVS ):/OVS/Repositories/0004fb00000300006cfeb81c12f12f00/VirtualDisks/0004fb000012000055e0fc4c5c8a35ee.img ** ** = to identify your virtual disk you have verify its name under the "vm.cfg" file of your new guest.Clone VI virtual-disk to OVS virtual-diskdd if=/dev/mapper/6000F4B00000000000210135bef64994-6000F4B00000000000610135c3a0b8cb of=/OVS/Repositories/0004fb00000300006cfeb81c12f12f00/VirtualDisks/0004fb000012000055e0fc4c5c8a35ee.img Clean unsupported parameters and changes on OVS.1. Restore original /etc/lvm/lvm.conf # By default for OVS we restrict every block device: filter = [ "r/.*/" ] and uncomment the line starting with "filter" as above.2. Force-stop lvm2-monitor service # service lvm2-monitor force-stop 3. Restore original /etc/lvm directories ( archive, backup and cache ) # cd /etc/lvm # rm -fr archive backup cache; mkdir archive backup cache4. Reboot OVSRefresh OVS repository and start your guest.By OracleVM Manager refresh your repository:By OracleVM Manager start your "migrated" guest: Comments and corrections are welcome. Simon COTER

Read the article

Extending Expression Blend 4 & Blend for Visual Studio 2012

- by Chris Skardon

Just getting this off the bat, I presume this will also work for Blend 5, but I can’t confirm it… Anyhews, I imagine you’re here because you want to know how to create an addin for Blend, so let’s jump right in there! First, and foremost, we’re going to need to ensure our development environment has the right setup, so the checklist: Visual Studio 2012 Blend for Visual Studio 2012 OK, let’s create a new project (class library, .NET 4.5): Hello.Extension The ‘.Extension’ bit is very very important. The addin will not work unless it is named in this way. You can put whatever you want at the front, but it has to have the extension bit. OK, so now we have a solution with one project. To this project we need to add references to the following things: Microsoft.Expression.Extensibility (from c:\program files\Microsoft Visual Studio 11.0\Blend\ -- x86 folder if you are on an x64 windows install) Microsoft.Expression.Framework (same location as above) PresentationCore PresentationFramework WindowsBase System.ComponentModel.Composition Got them? ACE. Let’s now add a project to contain our control, so, create a new WPF Application project, cunningly named something like ‘Hello.Control’… (I’m creating a WPF application here, because I’m too lazy to dig up the correct references, and this will add all the ones I need ) Once that is created, delete the App.xaml and MainWindow.xaml files, we won’t be needing them. You will also need to change the properties of the project itself, so it is only a class library. Once that is done, let’s add a new UserControl, which will be this: <UserControl x:Class="Hello.Control.HelloControl" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" mc:Ignorable="d" d:DesignHeight="300" d:DesignWidth="300"> <Grid> <TextBlock Text="HELLO!!!"/> </Grid> </UserControl> Impressive eh? Now, let’s reference the WPF project from the Extension library. All that’s left now is to code up our extension… So, add a class to the Extension project (name wise doesn’t matter), and make it implement the IPackage interface from the Microsoft.Expression.Extensibility library: public class HelloExtension : IPackage { /**/ } We’ll implement the two methods we need to: public class HelloExtension : IPackage { public void Load(IServices services) { } public void Unload() { } } We’re only really concerned about the Load method in this case, as let’s face it, the extension we have doesn’t need to do a lot to bog off. The interesting thing about the Load method is that it receives an IServices instance. This allows us to get access to all the services that Expression provides, in this case we’re interested in one in particular, the ‘IWindowService’ So, let’s get that bad boy… private IWindowService _windowService; public void Load(IServices services) { _windowService = services.GetService<IWindowService>(); } Nailed it… But why? The WindowService allows us to register our UserControl with Blend, which in turn allows people to activate and see it, which is a big plus point. So, let’s do that… We’ll create an ‘Initialize’ method to create our new control, and add it to the WindowService: private HelloControl _helloControl; public void Initialize() { _helloControl = new HelloControl(); if (_windowService.PaletteRegistry["HelloPanel"] == null) _windowService.RegisterPalette("HelloPanel", _helloControl, "Hello Window"); } First we check that we’re not already registered, and if we’re not we register, the first argument is the identifier used by the service to, well, identify your extension. The second argument is the actual control, the third argument is the name that people will see in the ‘Windows’ menu of Blend itself (so important note here – don’t put anything embarrassing or (need I say it?) sweary…) There are only two things to do now - Call ‘Initialize()’ from our Load method, and Export the class This is easy money – add [Export(typeof(IPackage))] to the top of our class… The full code will (should) look like this: [Export(typeof (IPackage))] public class HelloExtension : IPackage { private HelloControl _helloControl; private IWindowService _windowService; public void Load(IServices services) { _windowService = services.GetService<IWindowService>(); Initialize(); } public void Unload() { } public void Initialize() { _helloControl = new HelloControl(); if (_windowService.PaletteRegistry["HelloControl"] == null) _windowService.RegisterPalette("HelloControl", _helloControl, "Hello Window"); } } If you build this and copy it to your ‘Extensions’ folder in Blend (c:\program files\microsoft visual studio 11.0\blend\) and start Blend, you should see ‘Hello Window’ listed in the Window menu: That as they say is it!

Search Results

Search found 1256 results on 51 pages for 'activate'.

Page 44/51 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51 | Next Page >

- by mstaessen

- by eric01

- by happysencha

- by germandb

- by Sergei

- by James Fleming

- by thatjeffsmith

- by ola karlsson

- by Mysticgeek

- by andrewbrust

- by MarkPearl

- by Jinxi

- by DigiMortal

- by Dave B.

- by Martin Hinshelwood

- by JKenderdine

- by Tim Dexter

- by Dave Voyles

- by Mike Stiles

- by Mohgeroth

- by George Maggessy

- by Kelly Jones

- by scoter

- by Chris Skardon

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51 | Next Page >