Search Results

Search found 3177 results on 128 pages for 'david sowsy'.

Page 44/128 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• Why does my PC sometimes think I am constantly pressing the control key?

  - by David Faux

  I was browsing the web with Chrome and pressed f. A search box appeared. I then pressed s, after which Chrome asked if I wanted to save the web page. I soon realized that my PC was thinking that I was constantly pressing the Ctrl key regardless of what program I was using. In response, I tried clicking both of my Ctrl keys a few times to no avail. This problem arises sporadically as I work. I am not sure what is triggering it. Why could this problem be occurring? Is it the keyboard or software? How should I respond?

  Read the article

• VLAN Tagging Traffic on Cisco Switch

  - by David W

  I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

  Read the article

• How do I remotely deploy a software package on Linux system?

  - by David MZ

  I have a software package I wrote in Mono and I want to be able to deploy it to Ubuntu server as part of my move to continuous integration and deployment work flow. I was wondering if there is a tool to help me do that, some of the tasks I will need is Register a new domain/hostname with linux Install packaegs using apt-et Copy files Run some bash scripts What are the solutions to streamline this process to automate, I understand that is more then one answer to this, I would love to hear all the methods pros and cons. Thank you

  Read the article

• Tomato VPN connect but cannot ping LAN IP

  - by David Hamilton

  I've setup TomatoVPN using these settings on the server: TAP UDP 1194 Client address pool 10.10.9.1 -10.10.9.254 LAN clients are configured with 10.10.10.x I can connect from a remote client, but pinging anything in the 10.10.10.x results in a "Destination Host Unreachable" error. Here's my client configuration script: remote x.x.x.x 1194 client dev tap0 proto udp resolv-retry infinite nobind persist-key persist-tun float ca ca.crt cert client1.crt key client1.key ns-cert-type server Any suggestions as how I can make this properly bridge the two networks?

  Read the article

• Ubuntu 10.04 Windows2003 adding a route for GPO assignment

  - by David Carvalho

  I want the PC's that receive IP from my Ubuntu DHCP3-server to be able to retrieve the GPOs that are on my windows 2003 server. I'm using virtualbox and 3 virtual machines: 1 windows 2003 server 192.168.0.2 with 1 NIC (internal network). 1 ubuntu server 10.04 lts 192.168.0.1 with 1 NIC (internal network) and 3 aliases 192.168.21.0, 192.168.22.0, 192.168.100.0 1 Windows XP machine with 3 NIC's (internal network).

  Read the article

• Uneven Cassandra load

  - by David Keen

  Should a three node Cassandra cluster with a replication factor of 3 have the same load value for all three nodes? We are using a random partitioner and NetworkTopologyStrategy. Nodetool ring shows equal values for "Owns" but unequal values for "Load". Load Owns Token 113427455640312821154458202477256070484 16.53 GB 33.33% 0 14.8 GB 33.33% 56713727820156410577229101238628035242 15.65 GB 33.33% 113427455640312821154458202477256070484 Running nodetool repair and cleanup on each node brought the load a little closer but it still seems quite unbalanced. Is this considered normal?

  Read the article

• Trouble Connecting to Virtual Machine after IP address Change

  - by David

  I have a VMware image running a copy of Fedora 11 which is hosted on a remote server. The remote server recently had its IP address change. I'm now unable to connect to my virtual machine. The server admin assures me that my virtual machine is running and assigned the new IP address. I have checked the firewalls and had the remote admin restart the VM instance. Neither of these fixed the problem. How do I troubleshoot a remote server which I am unable to SSH to? I'm actually even unable to ping the remote IP (connection timed out).

  Read the article

• Windows Update and lsass.exe

  - by David

  I have a brand new installation of Windows XP (SP1 or older). I installed Norton AntiVirus, Firefox, Putty, and Cygwin. No other software is present. Windows Update finds the following 64 updates: KB905760, KB978262, Internet Explorer 8, KB71961, KB954155, KB968816, KB923561, KB950762, KB949402, KB950974, KB951376, KB951748, KB952004, KB952954, KB955069, KB956572, KB956802, KB956803, KB956844, KB958470, KB958869, KB959426, KB960803, KB960859, KB961501, KB969059, KB970238, KB970238, KB971032, KB971468, KB971657, KB972270, KB973507, KB973815, KB973904, KB974112, KB974318, KB974392, KB975025, KB975560, KB975561, KB975713, .......) When these updates are applied, the system reboots to a black screen with two error messages. The first error message says: lsass.exe - Application Error The application failed to initialize properly (0xc00000142). Click on OK to terminate the application. The second error message says: services.exe - Application Error The application failed to initialize properly (0xc00000142). Click on OK to terminate the application. I then proceed to boot into Safe Mode, use System Restore, and everything works fine again until the 64 updates re-appear in Windows Update. I can see two options: disable Auto-Updates or install each of the 64 updates one at a time until finding the troublesome update. Does anyone have any better ideas?

  Read the article

• Is there a good hotkey cheatsheet for using Latex in Emacs?

  - by David Brown

  Is there a good hotkey cheatsheet for using Latex in Emacs? A few minutes of googling didn't turn up anything.

  Read the article

• Unmanaged Network Switch vs Managed Network Switch

  - by David

  Currently I have an unmanaged POE switch connected to a Linksys router. I am thinking of upgrading my POE switch to a gigabit POE switch, the only problem is that the switch that I want to get is a managed switch. So here's my question: with a managed switch, can I still connect all of my devices to it and have the devices request IP addresses from the DHCP server within the Linksys router or will the devices request IPs from the managed switch since I believe the switch has its own DHCP server as well?

  Read the article

• How to identify cause of system lock on debian squeeze?

  - by David Sanders

  I have a desktop system at work with debian squeeze installed. Every couple days or so, when I come in in the morning, the system appears to be asleep and won't wake up. I suspect it goes into power save mode and then doesn't receive the wake up signal when I click the mouse or touch the keyboard. Does anyone know where I should look in order to start tracking this down? Like log files, etc? I doubt it, but maybe the fact that I'm using a mac aluminum usb keyboard and a wireless usb mouse (that has an off switch) has something to do with it? Maybe, when I turn my mouse off at the end of the day, the system loses track of the device somehow? I dunno :P. Thanks in advance.

  Read the article

• Windows 7: Server disappearing from Network window

  - by David Veeneman

  I am running a small (three computer) network on a Windows Server 2003 domain. All of the computers were just upgraded to Windows 7. Since the upgrade, the icon for the domain server periodically disappears from the Network window on all three computers. It doesn't happen at the same time on all computers--the icon typically disappears from one machine, but not the others. And it's not always the same computer. The network connection is still there--I can type \\myserver and get to the network shares. It's simply the icon that's disappearing. Has this happened to anyone else? Any suggestions for a fix? Thanks in advance.

  Read the article

• Apache httpd workers retry

  - by David Newcomb

  I have an Apache httpd web server running mod_proxy and mod_proxy_balancer. The whole of /somedir is sent to 2 worker machines which service the requests using the round robin scheduler. Each worker machine is running IIS but I don't think that is important. I can demonstrate the load balancer working by repeatedly requesting a single page which contains the IP address of the machine and can see that it switches from one to the other in a predictable round robin fashion. If I switch off one of the IIS servers and start requesting the same page then each page only contains the IP address of the machine that is up. However, if I start IIS and don't run my IIS application then /somedir returns 500 (as it should). I've added 500 to the failonstatus (Apache 2.4) so when it hits the error Apache places the worker machine into error state. Apache still returns the proxy error to the client though. How can I make Apache catch the proxy failure and retry using a different worker in the same way that a connection failure does. Update There is almost the same question asked in StackOverflow so joining them together. http://stackoverflow.com/questions/11083707/httpd-mod-proxy-balancer-failover-failonstatus-transperant-switching

  Read the article

• wild card redirects issue giving error this webpage has a redirect loop

  - by david

  In my website I changed or better word modified the directory name ""vehicles-cars"" to ""vehicles-cars-for-sale"" when i tried to redirect using wild card redirect my old directory name to new directory name in my web hosting cpanel account. every time when i open pages from that directory i am getting error code. This web-page has a redirect loop. The website is php. The problem is that that my lots of pages from old directory are indexed in googles and they are getting duplicate contents. If I redirect single page it works perfect but there are lots of pages so I need wild card redirect to redirect whole directory . I really need some advice what to do with this problem. Here is .htaccess file code for redirect thanks RewriteEngine on RewriteCond %{HTTP_HOST} ^example\.com$ [OR] RewriteCond %{HTTP_HOST} ^www\.example\.com$ RewriteRule ^vehicles\-cars\/?(.*)$ "http\:\/\/example\.com\/vehicles\-cars\-for\-sale\/$1" [R=301,L] i have other wilcard redirect of whole directory with same code and its working perfect here is the code in .htaccss file which is same as above and working perfect for this directory RewriteCond %{HTTP_HOST} ^adsbuz\.com$ [OR] RewriteCond %{HTTP_HOST} ^www\.adsbuz\.com$ RewriteRule ^autos\/?(.*)$ "http\:\/\/adsbuz\.com\/vehicles\-cars\-for\-sale\/$1" [R=301,L] so i dont understand whats wrong with the above code please i really need some expert advice thanks again

  Read the article

• Nvidia Drivers on Debian / Lenny (Stable) -> Installation successful -> Monitors gets black

  - by David

  I have successfully installed the proprietary drivers for my nvidia (geforce 7300 gt) graphics card on debian/lenny. I know its not the best way to chose for driver installation ( see this link: http://wiki.debian.org/NvidiaGraphicsDrivers#non-freedrivers ). but the two ways seem to be possible for me (nvidia-kernel module compilation). Now the problem is that the monitors gets black, the power light starts blinking after i launch the x-server. Have a short look a the logs (output truncated from /var/log/Xorg.0.log): (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) Jul 28 17:10:11 NVIDIA(0): Enabling RENDER acceleration (II) Jul 28 17:10:11 NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) Jul 28 17:10:11 NVIDIA(0): enabled. (II) Jul 28 17:10:11 NVIDIA(0): NVIDIA GPU GeForce 7300 GT (G73) at PCI:1:0:0 (GPU-0) (--) Jul 28 17:10:11 NVIDIA(0): Memory: 262144 kBytes (--) Jul 28 17:10:11 NVIDIA(0): VideoBIOS: 05.73.22.25.00 (II) Jul 28 17:10:11 NVIDIA(0): Detected PCI Express Link width: 16X (--) Jul 28 17:10:11 NVIDIA(0): Interlaced video modes are supported on this GPU (--) Jul 28 17:10:11 NVIDIA(0): Connected display device(s) on GeForce 7300 GT at PCI:1:0:0: (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0): 400.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): 165.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): Internal Single Link TMDS (II) Jul 28 17:10:11 NVIDIA(0): Assigned Display Device: CRT-0 (==) Jul 28 17:10:11 NVIDIA(0): (==) Jul 28 17:10:11 NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select" (==) Jul 28 17:10:11 NVIDIA(0): will be used as the requested mode. (==) Jul 28 17:10:11 NVIDIA(0): (II) Jul 28 17:10:11 NVIDIA(0): Validated modes: (II) Jul 28 17:10:11 NVIDIA(0): "nvidia-auto-select" (II) Jul 28 17:10:11 NVIDIA(0): Virtual screen size determined to be 1280 x 1024 (--) Jul 28 17:10:11 NVIDIA(0): DPI set to (85, 86); computed from "UseEdidDpi" X config (--) Jul 28 17:10:11 NVIDIA(0): option (==) Jul 28 17:10:11 NVIDIA(0): Enabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp Here is the complete /etc/X11/xorg.conf file as generated by nvidia-xconfig: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:59 PDT 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "Module" Load "dbe" Load "extmod" Load "type1" Load "freetype" Load "glx" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" Hor

  Read the article

• Using IIS6 to run kill process. Executable hangs

  - by David

  I'm using the following code (any tried many variations) in a web page that is supposed to kill a process on the server: Process scriptProc = new Process(); SecureString password = new SecureString(); password.AppendChar('p'); password.AppendChar('s'); password.AppendChar('s'); password.AppendChar('w'); password.AppendChar('d'); scriptProc.StartInfo.UserName = "mylocaluser"; scriptProc.StartInfo.Password = password; scriptProc.StartInfo.FileName = @"C:\WINDOWS\System32\WScript.exe"; scriptProc.StartInfo.Arguments = @"c:\windows\system32\killMyApp.vbs"; scriptProc.StartInfo.UseShellExecute = false; scriptProc.Start(); scriptProc.WaitForExit(); scriptProc.Close(); The VBS file is supposed to kill a w3wp.exe process, but never works. There are no errors in the application log. It works locally. I noticed WScript.exe is in task manager every time I run the page, and never goes away. The process WScript.exe (and I tried others such a psexec.exe) is being run as a local user with admin rights (and I tried other types of users including domain admins) when run from IIS, but it works when run from the command line on the server.

  Read the article

• I am building a computer, will these components work? [closed]

  - by david

  Case: Coolermaster HAF 912 Graphic card: Sapphire RADEON HD 6850 Optical Drive: SONY SATA DVD-ROM PSU: Corsair CX500 RAM: G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) Desktop Memory Model F3-10666CL9D-8GBXL Motherboard: MSI Z77A-G43 Processor: Intel core i3 2120 Still don't know which harddrive to use, neither if i should buy a cpu cooler fan... so if you can help me, please

  Read the article

• Why is my DB read-only when attached to SQL Express, but not with SQL Web?

  - by David Rubin

  I have an .mdf/.ldf pair, originally created in 2008 R2 Standard, and well under 10GB, with ACLs: d:\db snapshot\DB_NAME.mdf SERVERNAME\SQLServerMSSQLUser$ACCOUNT$MSSQLSERVER:F OWNER RIGHTS:F BUILTIN\Administrators:F d:\db snapshot\DB_NAME_log.ldf SERVERNAME\SQLServerMSSQLUser$ACCOUNT$MSSQLSERVER:F OWNER RIGHTS:F BUILTIN\Administrators:F When I attach the database to an instance of SQL Express 2008 R2, it comes up as read-only. When exactly the same acls and user-accounts and SQLCMD statements are set up with SQL Web 2008 R2, it comes up writable. I looked at MSDN's comparison page but nothing jumped out at me. Why on earth is this happening? Thanks! UPDATE I just noticed that the name of the attached databases are different. On SQL Express (read-only) it matches the filename (e.g. DB_NAME); on SQL Web (writable) it matches the CUSTOM_NAME that I gave it in the attach command: CREATE DATABASE [CUSTOM_NAME] ON (FILENAME = 'PATH_TO_MDF'), (FILENAME = 'PATH_TO_LDF') FOR ATTACH

  Read the article

• "must issue a starttls command first" when MSSQL emails via Microsoft Online

  - by David

  I have written a stored procedure in MSSQL Server 2008 R2 which sends emails when my Application logs errors. It works fine on servers at our office but when I ran it on our remote servers I got must issue a starttls command first So maybe there is a setting somewhere which is different between the two servers, and that's why it's working on one and not the other. How do I set the server so that it issues a "starttls commaned first"?

  Read the article

• modprobe ndiswrapper - not found

  - by David

  I'm trying to use ndiswrapper on a Slackware 12 (I think) box, but I'm running into a problem with modprobe. Everything I find online says that it should be working, but for some unknown reason it isn't. Here's what I've done so far: Installed ndiswrapper (latest tarball, make, make install) Ran ndiswrapper -i on the WinXP driver for my USB wireless card Ran ndiswrapper -l which tells me the driver is present and the device is present (lsusb also confirms the device is present) Ran ndiswrapper -m which put an alias for wlan0 in /etc/modprobe.d/ndiswrapper.conf Ran depmod -a Ran modprobe ndiswrapper which tells me "FATAL: module ndiswrapper not found" Ran modprobe -l which shows no listing for ndiswrapper I even tossed in a reboot or two while trying various combinations of the above, still nothing. So naturally ifconfig wlan0 up isn't working because the device isn't being created, presumably because the module isn't loading the driver. Does anybody have any suggestions? Everything points to the notion that this should work fine, but modprobe just isn't able to find what it needs. Have I missed an important step?

  Read the article

• How to upgrade OS on Mac Mini with external USB Drive?

  - by David

  We have a G4 Mac Mini, circa 2005, running Mac OS X 10.4 Tiger, and we want to upgrade to 10.5 Leopard. We have a Leopard install disk, but the optical drive in this mini is broken. So we transferred the install disk image to a USB HDD, but now we can't figure out how to boot off it. From what I've read in Mac forums, some PPC Macs, including some G4's, have been able to boot from USB, even though it sounds like this wasn't officially supported, and it may well depend on the specific model of USB drive and Mac. My Mac says CPU is "PowerPC G4 (1.2)" and Boot ROM is "4.8.9f4". I was hoping I might just find somebody here who had that same Mac Mini and find out if they could make it work. I'd especially like to know any specifics about the USB drive they found success with. Any insights at all would be appreciated. Thanks.

  Read the article

• How do I access an Ubuntu VirtualBox guest at a static IP from an OS X host?

  - by David Siegel

  How does one configure an Ubuntu guest to use a static IP that's visible to an OS X host, and ensure that the static IP is independent of the host's network configuration? I previously used bridged networking for my guest, but I'm constantly moving my host between networks so the guest IP is always different. First, I tried setting the guest network configuration to NAT and forwarding host port 1022 to guest port 22, so I could at least ssh to a fixed address (localhost:1022): $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/Protocol" "TCP" $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/GuestPort" 22 $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/HostPort" 1022 Then, $ ssh localhost -p 1022 ssh: connect to host localhost port 1022: Connection refused But this didn't work (guest has no network access with NAT and OS X refused the connection, as you can see). I'd love a general solution that would let me communicate with my guest at a fixed IP.

  Read the article

• Strange sound from Laptop, Microphone, Speakers or Soundcard?

  - by David Schilling

  I have recently purchased a second hand computer. There didn't seem to be anything wrong with it on purchasing, however recently I have noticed a small issue. Any time I play sound or listen through my headphones, I can hear what seems to be the CPU working (ie when beginning a new task, there is a small crackling). Also if I tap my laptop I can hear the sound louder, as if it is being picked up by the mic and then playing that sound in real time through the speakers or headphones. I have tried reading other topics but cannot find an answer to this question. These are the specs I am running on; Windows 7 Home Premium 32bit Pentium Dual Core CPU T4300 @ 2.10Ghz 2.10Ghz I hope someone can help me with this issue, it would be much appreciated.

  Read the article

• In AD how to get groups the workstation is a member of from the workstation itself?

  - by David

  If I'm at the domain controller (in the Active Directory) to find out what groups the "XPSP3-A" workstation is a member of, I do: dsquery computer "CN=XPSP3-A,CN=Computers,DC=pvk,DC=local" -name XPSP3-A | dsget computer -memberof and receive the following: "CN=Sec Group 001,OU=OU1,DC=pvk,DC=local" "CN=Domain Computers,CN=Users,DC=pvk,DC=local" But how to do the same from the "XPSP3-A" workstation?

  Read the article

• Completely unintuitive Apache/PHP memory-freeing behavior

  - by David

  Okay, this one's weird. I have a Turnkey Linux server with a gig of dedicated RAM. It's running WP3.2 with a boatload of plug-ins. It's a new site, so it has very limited traffic (other than search engines, maybe 20 hits a week). Now, for a few weeks, every few days, it would max out on main RAM, start eating up virtual RAM, and then crash. It's had this behavior for a while and I've been trying to figure out which element was causing the crash. Nine days ago, I pointed my external server monitor to this server. I wrote a 5-line HTML file (not PHP and not WP) that the server monitor accesses every minute, to see if the server is up. So, now, nine days later, the server has been rock solid, up all the time, no memory leak at all. I changed NOTHING on the server itself to see this behavior change. Have you EVER seen anything like this? All the server monitor is doing is retrieving a single, super-simple HTML file and all the memory leak problems have gone away. Weird, eh?

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >