Search Results

Search found 1441 results on 58 pages for 'troubleshooting'.

Page 44/58 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• Windows 8 & Hyper-V Can't Bridge Wifi Connection

  - by xinunix

  So I have an odd issue that I can't quite figure out... I am running Windows 8 Enterprise on a Dell 6420 laptop. I have a Broadcom 802.11n wireless adapter. I am connected to an home router (Netgear WNDR3700) that is connected to the internet. It is a very simple home network setup. I am trying to stand-up a few VMs in Hyper-V and want the VMs to be able to access the internet over my wireless connection. I have found numerous examples of how to set this up using both External and Internal Virtual Switches but have yet to be able to get it to work on my machine. I have narrowed the issue down to the fact that my host machine always loses internet connection when I bridge my wifi connection (both when it is bridged automatically by windows when I setup an external virtual switch bound to the wifi adapter or if I do it manually by creating an internal virtual switch, right click on it and my wifi network and select "Bridge Connections".) In both cases after the bridge is established, my host machine can no longer connect to the internet. I am not sure where to start with troubleshooting this problem. After the bridge is setup, an ipconfig shows all netowrk devices on the machine as "Media Disconnected". I do know that the wireless adapter is connected to the router b/c it shows the connection as active and full-strength. The only thing I can possibly think of is that this machine also has the Cisco VPN client installed on it which installs a Cisco Virtual Network Adapter. Is it possible that this Cisco Virtual Adapter is causing me issues when I try to bridge? I saw some people had a similar issue with a VirtualBox virtual adapter when trying to share via Hyper-V. Any thoughts or suggestions on how to troubleshoot?

  Read the article

• Determine the time difference between two linux servers

  - by Paul

  I am troubleshooting a latency network issue on a network. It is probably a nic or cabling issue, but while I was going through the process of figuring it out, I was looking at the timings of a ping packet leaving a network card and arriving at another server. Both linux. So I have tcpdump running on both, and I issue a ping from one to the other, and back again, and looking at the timing differences might have shed light on where the latency is coming from. It is an academic exercise now, as I need to eliminate some more fundamental causes, but I was curious as to how this could be achieved. Given that ntpd is installed and running on two servers, how can I confirm the current time discrepency between the two servers, to whatever level of accuracy is possible - given that we are talking about latency on a local lan, which is ideally a millisecond or so. NTP itself is accurate to a couple of ms under good conditions, and as both servers are in the same environment, they should (presumably) achieve a similar level of accuracy, and so should have a time discrepency between them of a only few ms - but how can I check this?

  Read the article

• DNS Does Not Register at Off-site Locations

  - by Russ Warren

  First of all, let me give you the specifics of our setup: Windows Small Business Server 2008 Domain w/ all applicable updates on the DC The DC does DHCP for the main site The DC does DNS for all sites 3 sites including our headquarters where the DC is located All sites are connected through OpenVPN SSL tunnels terminated by an Untangle box at each site The 2 remote sites us the Untangle box as a DHCP server for their subnet, which assigns the DC as the primary DNS server Collection of Windows XP and Windows 7 workstations connected to the domain Here's the issue: All of the workstations at the main site register with the DNS server on the domain controller fine. As they grab an IP from the DHCP server, it updates the DNS server with the new host record. I have 2 systems (each at different remote sites) that fail to register with the DNS server. I've attempted the following troubleshooting steps: Confirmed the network adapter is using the DC as a DNS server Confirmed 2-way traffic is possible between DC and workstation Verified the "Register with DNS server" setting was checked in the adapter properties Attempted ipconfig /registerdns and received no errors For the time being, I have setup a DHCP reservation for these systems and manually created a host record. This seems to work fine, but I need a solution for any new systems that go out there.

  Read the article

• Excel file growing huge (>150 MB)

  - by Josh

  There is one particular Excel file that is used by a number of employees at my company. It is edited from both Excel 2003 and 2007, with the "Sharing" feature turned on to allow multiple writers at once. The file has a decent amount of data on several sheets with some basic formatting, and used to be about 6MB, which seems reasonable for its content. But after a few weeks of editing, the file grew to 10, then 20 MB, and eventually skyrocketed to more than 150 MB, even though it still has about the same amount of data as before. It now takes 5-10 minutes to open it, and that much time again to save it. The first time this happened, I copied the content of each sheet into a new, blank workbook, and saved the new workbook; this brought it back down to about 6MB. Now, it has blown up again. The workbook uses the "Data Validation" feature to limit the values in certain columns to the contents of a few named ranges. Copying all the data into a new workbook means re-setting up all the data validation, which is a pain and not something that we want to do every month. As a troubleshooting step, I tried saving the file in "XML Spreadsheet 2003" format, hoping to get some insight into what was being stored. Sure enough, the file was almost a gig, and almost all of the 10 million lines look like this: <NamedCell ss:Name="Z_21D5114F_E50C_46AC_AA4F_C3FF540C717F_.wvu.FilterData"/> <NamedCell ss:Name="Z_1EE2BA5E_3011_4F9A_8ACD_E58835250FC4_.wvu.FilterData"/> <NamedCell ss:Name="Z_1E3BDCEA_6A72_4ECC_BF4F_7B03CC66181E_.wvu.FilterData"/> I've seen a few VBScripts online to manage and enumerate named cells that are hidden in Excel's built-in interface, though I wonder how they'd handle my 10 million named cells. What I really need, though, is an understanding of why this keeps happening. What actions in excel could be causing this?

  Read the article

• Apache 403 Forbidden Error when accessing local web server using local IP address

  - by amjo324

  I have an odd problem when attempting to browse to pages stored on a local web server (Apache 2.2). The pages are served as expected when I browse to localhost or 127.0.0.1 on port 80. Yet when I attempt to browse to the same pages by referencing the local IP address (192.168.x.x), I receive a HTTP 403 (Forbidden) error. In essence, http://localhost:80 works but 192.168.x.x:80 doesn't even though I'm specifying the IP of the local machine. You may be thinking "who cares? just use localhost". However, this is the first step in troubleshooting why I cannot remotely access these pages from different hosts on my LAN. I'm presuming this can't be a firewall issue as I'm only connecting to the local machine. Even so, I verified there was no iptables rules that could be having an effect. I've checked the Apache error logs and the corresponding line of relevance is: [Sat Oct 19 07:38:35 2013] [error] [client 192.168.x.x] client denied by server configuration: /var/www/ I've inspected most of the apache config files and they don't appear to differ from what you would expect with a default install. I can't see anything in apache2.conf that would be a problem and httpd.conf is an empty file. This is an excerpt from /etc/apache2/sites-enabled/000-default: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> Any insight as to where I can look next to find a solution ? Thanks in advance.

  Read the article

• Web SMTP Server(foo.com) will not send mail to exchange server which is also(foo.com)

  - by Atom

  I think I understand this problem fully, but I do not know how to approach it or where to go in terms of troubleshooting. I've got my one domain http://foo.com that runs a Zen Cart installation that needs to be able to send emails to users(order confirmation, password reset). This works fine to send to any other domain BUT foo.com. I'm running a locally hosted exchange server that is foo.com, and we can send and receive email just fine. If I run tail -f /usr/local/psa/var/log/maillog I recieve this error: Apr 1 10:08:51 foo qmail-local-handlers[25824]: Handlers Filter before-local for qmail started ... Apr 1 10:08:51 foo qmail-local-handlers[25824]: from= Apr 1 10:08:51 foo qmail-local-handlers[25824]: [email protected] Apr 1 10:08:51 foo qmail-local-handlers[25824]: cannot reinject message to '[email protected]' Apr 1 10:08:51 foo qmail: 1270141731.583139 delivery 32410: failure: This_address_no_longer_accepts_mail./ Apr 1 10:08:51 foo qmail: 1270141731.584098 status: local 0/10 remote 0/20 I understand that the foo.com SMTP service doesn't have any account but the one that is used to authenticate mail being sent, so of course, I understand why it's saying 'this address no longer accepts mail'. My question is, how can I get the foo.com(web) SMTP service to handle emails meant for my exchange server([email protected]) or how do I handle the mail that needs to be sent to our exchange server? Is this something to do with MX records? Thanks in advance A

  Read the article

• How to troubleshoot connectivity when curl gets an *empty response*

  - by chad

  I want to know how to proceed in troubleshooting why a curl request to a webserver doesn't work. I'm not looking for help that would be dependent upon my environment, I just want to know how to collect information about exactly what part of the communication is failing, port numbers, etc. chad-integration:~ # curl -v 111.222.159.30 * About to connect() to 111.222.159.30 port 80 (#0) * Trying 111.222.159.30... connected * Connected to 111.222.159.30 (111.222.159.30) port 80 (#0) > GET / HTTP/1.1 > User-Agent: curl/7.19.0 (x86_64-suse-linux-gnu) libcurl/7.19.0 OpenSSL/0.9.8h zlib/1.2.3 libidn/1.10 > Host: 111.222.159.30 > Accept: */* > * Empty reply from server * Connection #0 to host 111.222.159.30 left intact curl: (52) Empty reply from server * Closing connection #0 So, I understand that an empty response means that curl didn't get any response from the server. No problem, that's precisely what I'm trying to figure out. But what more specific info can I derive from cURL here? It was able to successfully "connect", so doesn't that involve some bidirectional communication? If so, then why does the response not come also? Note, I've verified my service is up and returning responses. Note, I'm a bit green at this level of networking, so feel free to provide some general orientation material.

  Read the article

• Improving abysmal 802.11n wireless network

  - by concept

  I am in desperate need of help to improve the abysmal performance of my 802.11n wireless network. At best I get 30Mbs (this is an internet download) from a technology that boasts 300Mbs, even worse is the LAN where to date best i have ever gotten is 1Mbs. It is literally quicker to copy the file to a USB and walk it to the other computer. Infrastructure is this AP 802.11n only broadcasting at both 2.4GHz and 5GHz Mac with 802.11a/b/g/n card is connected to the AP via 5GHz Linux with 802.11a/b/g/n card is connected to AP via 2.4GHz I have conducted the following tests (results at end of post) Internet based speed test wired and wireless LAN file copy wired and wireless I have read: http://nutsaboutnets.com/troubleshooting-wi-fi-problems/ http://www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-- speed http colon //www.wi-fiplanet dot com/tutorials/7-tips-to-increase-wi-fi-performance.html Slow file transfer on network between two 802.11n laptops (connected directly together via access point) Wireless Network Performance Issues Slower than expected 802.11n wireless network speeds I have made the following optimizations AP broadcasts only 802.11n on both 2.4GHz and 5GHz frequencies 2.4GHz is on a channel with least interference (live in an apartment with lots of APs), this did make a 10Mb/sec improvement Our AP is the only one transmitting on the 5GHz freq. Security: WPA Personal WPA2 AES encryption Bandwidth: 20MHz / 40MHz (i assume this to be channel bonding) I have tried the following with 0 improvement Dropped the Fragment Threshold to 512 Dropped the Request To Send (RTS) Threshold to 512 and 1 Even thought of buying a frequency spectrum analyzer, until i saw the cost of them!!! Speed test results Linux Wired: DOWNLOAD 128.40Mb/s UPLOAD 10.62Mb/s www dot speedtest dot net/my-result/2948381853 Mac Wired: DOWNLOAD 118.02Mb/s UPLOAD 10.56Mb/s www dot speedtest dot net/my-result/2948384406 Linux Wireless: DOWNLOAD 23.99Mb/s UPLOAD 10.31Mb/s www.speedtest dot net/my-result/2948394990 Mac Wireless: DOWNLOAD 22.55Mb/s UPLOAD 10.36Mb/s www.speedtest dot net/my-result/2948396489 LAN NFS 53,345,087 bytes (51Mb) file Linux Mac NFS Wired: 65.6959 Mb/sec Linux Mac NFS Wireless: .9443 Mb/sec All help is appreciated, even testing methods will be accepted.

  Read the article

• How to re-join an AD2003 domain with Samba after deleting the machine account?

  - by Guss

  During some troubleshooting I deleted the machine account for a Linux server running samba from our AD 2003 domain. We are using Kerberos for authentication, and after I deleted the machine account I tried to join the domain again using net ads join -U Administrator But I keep getting Kerberos errors like these: [2009/08/18 16:14:36, 0] libads/kerberos.c:ads_kinit_password(228) kerberos_kinit_password [email protected] failed: Client not found in Kerberos database Failed to join domain: Improperly formed account name It appears as if samba remembers that it once had an account with the AD and keeps trying to reconnect to it, but I want to create a new account from scratch. I tried to delete all the .tdb files I could find as well as everything under /var/cache/samba but to no avail - it still behaves the same. I also tried to create the machine account on the AD side, but then I get a similar error when I try to join, about failure to authenticate with the machine account - it looks like samba tries the previous machine account password and I don't know how to reset it, or even if I could figure out what samba uses - how to set it in the AD. Any help would be greatly appreciated, as at this point the only thing I can think about is to reformat and reinstall the machine, and I would really REALLY love to not do that. Thanks in advance.

  Read the article

• Suspected Router problems, [closed]

  - by jordon_user

  I am new to this forum. I appreciate any help you can offer. I have been troubleshooting an error with both my WIRED Internet Connection I have 3 desktops running through this working connection (Router) with no problems. Two computers, one laptop and desktop experience the issue. If I connect directly to the Modem, on either, no problem on the internet. Through the Router, my computer connects for a period of time but if ever awaking my comp, or restarting, the yellow explanation mark returns. The only way I can get the connection up = cmd. ipconfig /release, ipconfig /renew. This constant command is annoying and was hoping for a permanent fix. Audio is also not working. I know its likely a driver error, but its an old comp we put together and if there's an easy fix itd be great to hear from you! If you need any more info just let me know. Thanks! THanks guys!

  Read the article

• Mapped networkdrive on logout

  - by Robuust

  I'm using a script to keep a mapped networkconnection alive, but ofcourse the mapped connection is gone when I logout. The point is now, that I'm running this on Windows Server 2008 R2, where I use remote desktop to login on the administrator account. However, it should remain logged in and not remove the mapped connection as this script takes care of not logging out on MS office 365 sharepoint. Is there a way to keep the mapped networklocation (L:) available after logout? So the script can run to remain the connection? # Create an IE Object and navigate to my SharePoint Site $ie = New-Object -ComObject InternetExplorer.Application $ie.navigate('https://xxx.sharepoint.com/') # Don't need the object anymore, so let's close it to free up some memory $ie.Quit() # Just in case there was a problem with the web client service # I am going to stop and start it, you could potentially remove this # part if you want. I like it just because it takes out a step of # troubleshooting if I'm having problems. Stop-Service WebClient Start-Service WebClient # We are going to set the $Drive variable here, this is just # going to tell the command what drive letter to map you can # change this to whatever you want (if you change it to a # drive that is already mapped it will overwrite it, so be careful. $Drive = "L:" # You can change the drive destiniation to whatever you want, # it has to be a document library or folder of course. $DrvDest = "https://xxx.sharepoint.com/files/" # Here is where we create the object to map the network drive and # then map the network drive $net = New-Object -ComObject WScript.Network; $net.mapnetworkdrive($Drive,$DrvDest) # That is the end of the script, now schedule this with task # scheduler and every so often and you should be set.

  Read the article

• (Mac Intel) HP PS driver prints in B&W from Adobe Reader after installing Cannon PS driver

  - by JohnB

  I have a unique problem that leaves me at a loss as to where to start troubleshooting. We have three Macs we use for graphics, two of which are PowerPC and one which is Intel. They are set up to print to an HP 5500dn, but occasionally this printer gets tied up with a massive print job, so I installed the PS driver (iR-PSv1.81MacOSX) for the Cannon C3200 Printer/copier on each of the machines. Both of the PowerPC Macs installed without issue, but the Intel Mac exhibits strange behavior: I've confirmed that while the Cannon driver is installed (whether or not the Cannon is set up for printing in print settings), the HP 5500dn will print in color from Safari, but only prints in black and white from Adobe Reader. The Cannon printer itself has not exhibited any strange behavior As soon as the Cannon driver is uninstalled, the HP 5500dn prints in color from Adobe Reader again. We run a network of Windows PCs, and the 'Mac room' mostly takes care of itself, so we don't have any experienced Mac administrators onsite. The Cannon is capable of Appletalk, but the PS driver seemed easier to work with (and Appletalk is currently disable on the Cannon. I'm not against using the Appletalk compatible drivers, but I would rather use the PS driver if at all possible - I don't want to open up the proverbial can of worms. If someone has any clues or suggestions that would help troubleshoot this problem, I would be grateful. I've already done some googling, but due to the obscure nature of this problem, I haven't been very successful. I don't like to create multiple threads on multiple sites, but I'm posting here due to Chopper3's suggestion on my post on ServerFault (http://serverfault.com/questions/135349/mac-intel-hp-ps-driver-prints-in-bw-from-adobe-reader-after-installing-cannon)

  Read the article

• Where to get working Sysinternals tools for Windows 2000?

  - by mihi

  Yes, I know Windows 2000 will run end-of-life in this year, but we still have a lot of Windows 2000 boxes we try to migrate but no idea if all of them can be migrated this year... Recently I downloaded a new Sysinternals Suite (most recent file date 2010-03-25) and noticed that some tools just do not work on Windows 2000 any longer, which makes troubleshooting a lot harder. I checked all the tools in the suite to check which tools do not work, and dug through to find older versions that do work, but I don't know if there are more recent ones (with fewer bugs) available. I did not find any way to download old versions from Sysinternals website. :-( So here is my list: Does not work Works ADExplorer.exe 1.30.0.0 ? Coreinfo.exe 2.00 ? disk2vhd.exe 1.5.0.0 ? livekd.exe 3.14 3.0 procdump.exe 1.72 ? Procmon.exe 2.8 (Frequent crashes) Filemon/Regmon 7.04 ShellRunas.exe 1.01 ? vmmap.exe 2.62 2.2 ZoomIt.exe 4.1 1.21 If you know of any more recent versions (preferrably with download links) that work on Windows 2000, or an official download link for older versions, it would be highly appreciated.

  Read the article

• Current wisdom on SQL Server and Hyperthreading?

  - by BradC

  Lots of articles out there (see Slava Oks's original SQL 2000 article and Kevin Kline's SQL 2005 update) recommend disabling hyperthreading on SQL servers, or at least testing your specific workload before enabling it on your servers. This issue is gradually becoming less relevant as true multi-core processors replace hyperthreaded ones, but what's the current wisdom on this issue? Does this advice change any with SQL 2005 64-bit, or SQL 2008, or Windows Server 2008? Ideally, this should be tested in advance in a staging environment, but what about for servers that have already made it into production with HT enabled? How can I tell if performance issues we're experiencing might be related to HT? Is there some specific combination of perfmon counters that might point me in that direction, as opposed to all the other things I normally pursue when working on improving SQL performance? Edit: This is especially attractive because of the potential for an across the board improvement for some of my high-cpu servers, but the client is going to want to see something concrete that helps me identify which servers really could benefit from disabling hyperthreading. Of course, conventional performance troubleshooting is ongoing, but sometimes any little bit helps.

  Read the article

• Git push over http (using git-http-backend) and Apache is not working

  - by Ole_Brun

  I have desperately been trying to get push for git working through the "smart-http" mode using git-http-backend. However after many hours of testing and troubleshooting, I am still left with error: Cannot access URL http://localhost/git/hello.git/, return code 22 fatal: git-http-push failed` I am using latest versions of Ubuntu (12.04), Apache2 (2.2.22) and Git (1.7.9.5) and have followed different tutorials found on the Internet, like this one http://www.parallelsymmetry.com/howto/git.jsp. My VHost file currently looks like this: <VirtualHost *:80> SetEnv GIT_PROJECT_ROOT /var/www/git SetEnv GIT_HTTP_EXPORT_ALL SetEnv REMOTE_USER=$REDIRECT_REMOTE_USER DocumentRoot /var/www/git ScriptAliasMatch \ "(?x)^/(.*?)\.git/(HEAD | \ info/refs | \ objects/info/[^/]+ | \ git-(upload|receive)-pack)$" \ /usr/lib/git-core/git-http-backend/$1/$2 <Directory /var/www/git> Options +ExecCGI +SymLinksIfOwnerMatch -MultiViews AllowOverride None Order allow,deny allow from all </Directory> </VirtualHost> I have changed the ownership of the /var/www/git folder to root.www-data and for my test repositories I have enabled anonymous push by doing git config http.receivepack true. I have also tried with authenticated users but with the same outcome. The repositories were created using: sudo git init --bare --shared [repo-name] While looking at the apache2 access.log, it appears to me that WebDAV is trying to be used, and that git-http-backend is never fired: 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "GET /git/hello.git/info/refs?service=git-receive-pack HTTP/1.1" 200 207 "-" "git/1.7.9.5" 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "GET /git/hello.git/HEAD HTTP/1.1" 200 232 "-" "git/1.7.9.5" 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "PROPFIND /git/hello.git/ HTTP/1.1" 405 563 "-" "git/1.7.9.5" What am I doing wrong? Is it an issue with the version of git and/or apache that I am using perhaps? BTW: I have read all the git http related questions on ServerFault and StackOverflow, and none of them provided me with a solution, so please don't mark this as duplicate.

  Read the article

• Very strange networking problem in all computers in my house

  - by Anthony

  I have three computers in my house: One desktop (wired), and two laptops (wireless). I'm using Cox Communications (yes they suck), and yesterday they had a major outage. I know it was them because I called them up when I started losing connection to the internet. All the computers can connect just fine, but they don't have internet access. It just says "local only". The weird thing is, some of them work occasionally. For the first day my laptop was working perfectly, while all the other computers couldn't connect. Later on in the day it got reversed, and the desktop was the one with internet access. By the second day the problem on Cox's end was fixed, but we still had no access. I called them up and they reset my modem, and did the usual troubleshooting stuff. It never fixed the problem, but we found out that the problem had to do with conflicting IP addresses. My router was a Linksys WRT54G and it was about 5 years old. I figured it might have gotten damaged from the outage since it was so old, and now it's having trouble "fixing itself" and giving out the proper IP addresses. So I bought a new router, a Cisco Linksys E1000. I set everything up, and still the same problem. My computer has access right now (that's how I'm writing this), but no other computers seem to be able to get access. Is there possible damage to the modem? Can someone help me please? Sorry for this being so long.

  Read the article

• Does Windows 7 Authenticate Cached Credentials on Startup

  - by Farray

  Problem I have a Windows domain user account that gets automatically locked-out semi-regularly. Troubleshooting Thus Far The only rule on the domain that should automatically lock an account is too many failed login attempts. I do not think anyone nefarious is trying to access my account. The problem started occurring after changing my password so I think it's a stored credential problem. Further to that, in the Event Viewer's System log I found Warnings from Security-Kerberos that says: The password stored in Credential Manager is invalid. This might be caused by the user changing the password from this computer or a different computer. To resolve this error, open Credential Manager in Control Panel, and reenter the password for the credential mydomain\myuser. I checked the Credential Manager and all it has are a few TERMSRV/servername credentials stored by Remote Desktop. I know which stored credential was incorrect, but it was stored for Remote Desktop access to a specific machine and was not being used (at least not by me) at the time of the warnings. The Security-Kerberos warning appears when the system was starting up (after a Windows Update reboot) and also appeared earlier this morning when nobody was logged into the machine. Clarification after SnOrfus answer: There was 1 set of invalid credentials that was stored for a terminal server. The rest of the credentials are known to be valid (used often & recently without issues). I logged on to the domain this morning without issue. I then ran windows update which rebooted the computer. After the restart, I couldn't log in (due to account being locked out). After unlocking & logging on to the domain, I checked Event Viewer which showed a problem with credentials after restarting. Since the only stored credentials (according to Credential Manager) are for terminal servers, why would there be a Credential problem on restart when remote desktop was not being used? Question Does anyone know if Windows 7 "randomly" checks the authentication of cached credentials?

  Read the article

• HTB.init / tc behind NAT

  - by Ben K.

  I have an Ubuntu 10 box that I'm trying to set up as a bandwidth-shaping router. The machine has one WAN interface, eth0 and two LAN interfaces, eth1 and eth2. NAT is configured using MASQUERADE as described at InternetConnectionSharing. I'm mostly concerned with shaping outbound traffic from the LAN interfaces -- in the end, I'd like to end up with a hard 768Kbps limit per-LAN-interface (rather than a limit on eth0 pooled across all interfaces). I installed HTB.init, and riffing on the examples, tried to set this up on eth1 by putting three files into /etc/sysconfig/htb: /etc/sysconfig/htb/eth1 DEFAULT=30 R2Q=100 /etc/sysconfig/htb/eth1-2.root RATE=768Kbps BURST=15k /etc/sysconfig/htb/eth1-2:30.dfl RATE=768Kbps CEIL=788Kbps BURST=15k LEAF=sfq I can /etc/init.d/htb start and /etc/init.d/htb stats and see information that /seems/ to suggest it's working...but when I try pulling a large file via the WAN interface the shaping clearly isn't in effect. Any suggestions? My guess is it has something to do with where the shaping falls in the NAT chain, but I really have no idea where to begin troubleshooting this. ---- Update: Here's my /etc/init.d/htb list output, it seems to make sense -- the default rate for eth1 is 768Kbps? ### eth0: queueing disciplines qdisc htb 1: root refcnt 2 r2q 100 default 30 direct_packets_stat 0 qdisc sfq 30: parent 1:30 limit 127p quantum 1514b perturb 10sec ### eth0: traffic classes class htb 1:2 root rate 768000bit ceil 768000bit burst 1599b cburst 1599b class htb 1:30 parent 1:2 leaf 30: prio 0 rate 6144Kbit ceil 6144Kbit burst 15Kb cburst 1598b ### eth0: filtering rules filter parent 1: protocol ip pref 100 u32 filter parent 1: protocol ip pref 100 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 100 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:30 match 00000000/00000000 at 12 match 00000000/00000000 at 16 ### eth1: queueing disciplines qdisc htb 1: root refcnt 2 r2q 100 default 30 direct_packets_stat 0 qdisc sfq 30: parent 1:30 limit 127p quantum 1514b perturb 10sec ### eth1: traffic classes class htb 1:2 root rate 768000bit ceil 768000bit burst 1599b cburst 1599b class htb 1:30 parent 1:2 leaf 30: prio 0 rate 6144Kbit ceil 6144Kbit burst 15Kb cburst 1598b

  Read the article

• Unable to logon using terminal server connection

  - by satch

  I have several W2K3 SP2 servers, admin TS enabled. I discovered this morning, I was unable to logon into some of them. I've a couple of Citrix servers in different farms, a SAP (IA64) app server and a cvs server. All of them show same sympthoms; remote connections are refused. I've been able to logon locally, and terminal server service is up, there are no users (so connections are not depleted). There are no errors in log in most servers. One of the Citrix ones, reported following errors: Event ID 50 Source TermDD Type Error Description The RDP protocol component X.224 detected an error in the protocol stream and has disconnected the client. and Event ID 1006 Source TermService Type Error Description The terminal server received large number of incomplete connections. The system may be under attack. Anyway, I suppose these errors appear because server isn't working, and Citrix users try to logon massively. (I nmap'ed server and port seems up). I've solved this problem rebooting before, but with so many servers affected it seems like a crappy workaround. Any idea about troubleshooting it properly? Thanks in advance

  Read the article

• Hubs/switches taking out switches?

  - by Bart Silverstrim

  Here's the issue...we have a network with a lot of Cisco switches. Someone plugged in a hub on the network, and then we started seeing "weird" behavior; errors in communication between clients and servers, or network timeouts, dropping network connections, etc. It seemed that somehow that hub (or SOHO switch) was particularly freaking out our Cisco 3700 series switches. Disconnect that hub or netgear-type SOHO switch and things settled down again. We're in the process of trying to get a centralized logging server for SNMP and management, etc., to see if we can trap errors or narrow down when someone does this sort of thing without our knowledge because things seem to work, for the most part, without issue, we just get freaky oddball incidents on particular switches that don't seem to have any explanation until we find out someone decided to take matters into their own hands to expand available ports in their room. Without getting into procedure changes or locking down ports or "in our organization they'd be fired" answers, can someone explain why adding a small switch or hub, not necessarily a SOHO router (even a dumb hub apparently caused the 3700's to freak out) sending DHCP request out, will cause issues? The boss said it's because the Cisco's are getting confused because that rogue hub/switch is bridging multiple MAC's/IP's into one port on the Cisco switches and they just choke on that, but I thought their routing tables should be able to handle multiple machines coming into the port. Anyone see that behavior before and have a clearer explanation of what's happening? I'd like to know for future troubleshooting and better understanding that just waving my hand and saying "you just can't".

  Read the article

• 2000 Server, User can't logon

  - by Mike I

  I hope you can help me. I recently upgraded a workstation at my office (to a whole new machine) and ran into a pretty serious problem. Friday until 5:00 PM, I could access my mail on 2000 Exchange server. When I shut the old workstation down and put in the new workstation, I tried to set up an account. When I put the server name in appropriate field and typed my username and hit check names, my username does not come up. So to troubleshoot, (It also is a SMB server) I try to logon to my file share. (My local credentials are the same as server credientials of user account) When I try to logon to share, I just get the Username/Password screen (Never had gotten that before since credentials are the same) Again, in troubleshooting mode, I try to log on to my user from another workstation. Still can't authenticate via my user. Every other user can authenticate and load up their shares/mailboxes. I have restored Exchange from the backup as of 3 days ago (Thursday) but the exact same issue is still there. I really do not understand what is wrong and what else I can do to troubleshoot. If anyone has some pointers for me, I will surely accept them. Thanks, Mike

  Read the article

• Exchange 2007 relay from sendmail, message "Undelivered". Possible reasons?

  - by garlicman

  Note: This is my re-post from Stackoverflow. I've been messing with a test environment for security purposes where a DMZ RHEL5 sendmail server is used as a relay for an Exchange 2007 server. Exchange is working in the environment, I have Vista and XP VMs using Outlook on the Domain to send e-mail to each other. I've been trying to simulate an external internet VM sending an e-mail to the DMZ sendmail relay, which forwards to the Exchange server. Before everyone thinks this is too big a problem/question, I've followed the sendmail/Exchange guides and all I want to know is how I can determine why a relayed message/e-mail in Exchange is "Undelivered". Basically I send a SMTP message to the sendmail server, which relayed to my Exchange. The /var/log/maillog shows the e-mail being relayed to Exchange. Nov 17 13:41:22 externalmailserver sendmail[9017]: pAHIfMuW009017: from=<[email protected]>, size=1233, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA, relay=[10.50.50.1] Nov 17 13:42:17 externalmailserver sendmail[9050]: pAHIfMuW009017: to=<[email protected]>, delay=00:00:55, xdelay=00:00:36, mailer=relay, pri=121233, relay=mailserver.xyz.local. [192.168.1.20], dsn=2.0.0, stat=Sent (<[email protected]> Queued mail for delivery) This is good, but the To never receives the e-mail from Exchange. So I started poking around Exchange. In the "Message Tracking" Troubleshooting Assistant I queried the processed messages and found this: (I had to copy and paste the cells... sorry for the format) 2011/11/17 RECEIVE SMTP <[email protected]> "Undelivered Mail Returned to Sender" [email protected] [email protected] 192.168.100.10 MAILSERVER\DMZ Relay [email protected] I just want to know if anyone has any suggestions on why the DMZ Relay Connector I setup isn't relaying and is instead returning the forwarded e-mail to sender as Undelivered? My Exchange Relay Receive Connector is pretty simple. The Exchange server's FQDN is set as the HELO response, all available IP addresses can receive relayed e-mail, and the IP address of my sendmail server is specifically set as a remote server.

  Read the article

• Mail queue directory stuck in IIS SMTP server

  - by Loftx

  Hi there, We have an IIS SMTP server which sends out a largish number of mails (4000 or so) in batches overnight, and recently we've seen mails get "stuck" in the queue directory. Normally restarting the SMTP service seems to fix this, but it's happened a few times so I'm looking for more information. We sent out around 12,000 emails last night in 3 batches of roughly 4000. Around 10 hours later there are still 2000 or so in the queue directory which don't seem to be leaving the queue. Any new mails which appear in the queue are picked up almost immediately and sent to their destination, but these 2000 or so don't seem to move. Looking at the date modified on the emails some match up with the time they were sent, but around 1000 of them have modified dates stretching up to now. e.g. there was one mail with a date in the message headers of 5:30 this morning, but it's date modified is 11:50 and there are 3 other messages with a date modified of 11:50, then 5 with 11:49, 2 with 11:45 stretching back for a few hours and all with actual message headers far earlier. The logs for the server look like this 11:54:52 127.0.0.1 EHLO - 250 11:54:52 127.0.0.1 MAIL - 250 11:54:52 127.0.0.1 RCPT - 250 11:54:52 127.0.0.1 DATA - 250 11:54:52 127.0.0.1 QUIT - 240 11:54:53 85.115.62.190 - - 0 11:54:53 85.115.62.190 EHLO - 0 11:54:53 85.115.62.190 - - 0 11:54:53 85.115.62.190 MAIL - 0 11:54:53 85.115.62.190 - - 0 11:54:53 85.115.62.190 RCPT - 0 11:54:53 85.115.62.190 - - 0 11:54:53 85.115.62.190 DATA - 0 11:54:53 85.115.62.190 - - 0 11:54:54 85.115.62.190 - - 0 11:54:54 85.115.62.190 QUIT - 0 11:54:54 85.115.62.190 - - 0 All codes are either 250 or 240 or 0. I believe 250 and 240 indicate success, but I don't know what all the 0s are. Could someone with more experience of mail server troubleshooting give me a hand or tell me what to try next. Thanks, Tom

  Read the article

• Booting Debian5 (Lenny) on 2.6.16 Kernel

  - by bk

  Due to a proprietary kernel module that I don't have the source to and is very picky about what kernel versions it will load into (even with modprobe --f), I find myself in need of running a 2.6.16.XX kernel on my Debian5 machine. The machine boots fine with the 2.6.26-2 stock kernel, and I have successfully build and booted 2.6.26 and 2.6.31 based kernels by making a .deb and the ndoing dpkg -i. However, when I do the same approach for 2.6.16, the kernel hangs at boot. I'm testing this in a VMWare image, so I don't think its an issue of newer hardware not supported by the older kernel. For a working kernel, at boot I get: Uncompressing Linux.. OK booting the kernel Loading, please wait... mdadm: No devices listed in the conf file were found kinit name_to_dev_t /dev/hda5 (dev5,3) ... With 2.6.16.60, I never get the kinit message. It hangs after the mdadm line. There are no mdadm arrays on this machine, so I doubt its an issue inside the mdadm stuff, which is supposed to just error out as it does in the 2.6.26 case above, but for some reason I'm getting stuck getting into kinit. I've been banging my head against this wall so I'm very open to suggestions on how to go about troubleshooting this.

  Read the article

• BackupPC - why does it use rsync --sender --server ... ?

  - by Jakobud

  I'm in the process of experimenting with BackupPC on a CentOS 5.5 server. I have everything pretty much setup with default values. I tried setting up a basic backup for a host's /www directory. The backup fails with the following errors: full backup started for directory /www Running: /usr/bin/ssh -q -x -l root target /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Xfer PIDs are now 30395 Read EOF: Connection reset by peer Tried again: got 0 bytes Done: 0 files, 0 bytes Got fatal error during xfer (Unable to read 4 bytes) Backup aborted (Unable to read 4 bytes) Not saving this as a partial backup since it has fewer files than the prior one (got 0 and 0 files versus 0) First of all, yes I have my ssh keys setup to allow me to ssh to the target server without requiring a password. In the process of troubleshooting, I tried the above ssh command directly from the command line, and it hangs. Looking at the end of the debug messages for SSH I get: debug1: Sending subsystem: /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Request for subsystem '/usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/' failed on channel 0 Next I started looking at the rsync flags. I did not recognize --server and --sender. Looking at the rsync man pages, sure enough, I don't see anything about --server or --sender in there. What are those in there for? Looking at the BackupPC config I have this: RsyncClientPath = /usr/bin/rsync RsyncClientCmd = $sshPath -q -x -l root $host $rsyncPath $argList+ And for the arguments, I have the following listed: --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive Notice there is no --server, --sender or --ignore-times. Why are these things getting added in? Is this part of the problem?

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >