Search Results

Search found 19625 results on 785 pages for 'local groups'.

Page 440/785 | < Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >

  • Simple Cisco ASA 5505 config issue

    - by Ben Sebborn
    I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

    Read the article

  • Why are my httpd mpm_prefork processes being reaped so quickly?

    - by Dan Pritts
    We've got a system running RHEL6, x64. We are using a local installation of apache 2.2.22 from source. we serve primarily: mod_perl applications (with a local installation of perl 5.16.0) tomcat applications proxied with mod_jk Here is some context; the main question is below. All of this talks to an Oracle backend. We are having issues with Oracle becoming unresponsive. We think this is because we're hitting the maximum process limit in oracle. We've upped the process limit, but now we are hitting memory pressure on the oracle server. We have tons of oracle sessions sitting idle. I can trace a bunch of them back to the httpd processes. We have mod_perl's Apache::DBI start up a new connection to the database with each httpd child that's spawned. We are concerned that these are not always getting closed out properly when the httpd's exit...and the httpd's are exiting very frequently. I know that it would be good to modify the mod_perl applications to use some better form of db connection pooling; we plan to pursue that but would like to solve our immediate problem sooner. So here's the main question. We are using the prefork MPM. The apache child processes are lasting at most a few minutes. Log analysis shows that each one is serving fewer than 50 clients before exiting; the last request each child serves is OPTIONS * HTTP/1.0 on some sort of internal connection; I'm under the impression that this is a "ping" from the master process. I've adjusted the MPM config as follows. I didn't want to raise MinSpareServers too high, because, after all, i'm trying to minimize the number of sessions to oracle. MinSpareServers 5 MaxSpareServers 30 MaxClients 150 MaxRequestsPerChild 10000 Right now we're serving 250-300 requests per minute. We've got 21 httpd's running, the eldest (other than the master, owned by root) being 3 minutes old. This rate of reaping of the apache children really seems excessive. What could be causing it? Apache was built with: $ ./configure --prefix=/opt/apache --with-ssl=/usr/lib --enable-expires --enable-ext-filter --enable-info --enable-mime-magic --enable-rewrite --enable-so --enable-speling --enable-ssl --enable-usertrack --enable-proxy --enable-headers --enable-log-forensic Apache config info: % /opt/apache/bin/httpd -V Server version: Apache/2.2.22 (Unix) Server built: Jul 23 2012 22:30:13 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.5, APR-Util 1.4.1 Compiled using: APR 1.4.5, APR-Util 1.4.1 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/opt/apache" -D SUEXEC_BIN="/opt/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" modules are compiled into apache rather than shared libs: % /opt/apache/bin/httpd -l Compiled in modules: core.c mod_authn_file.c mod_authn_default.c mod_authz_host.c mod_authz_groupfile.c mod_authz_user.c mod_authz_default.c mod_auth_basic.c mod_ext_filter.c mod_include.c mod_filter.c mod_log_config.c mod_log_forensic.c mod_env.c mod_mime_magic.c mod_expires.c mod_headers.c mod_usertrack.c mod_setenvif.c mod_version.c mod_proxy.c mod_proxy_connect.c mod_proxy_ftp.c mod_proxy_http.c mod_proxy_scgi.c mod_proxy_ajp.c mod_proxy_balancer.c mod_ssl.c prefork.c http_core.c mod_mime.c mod_status.c mod_autoindex.c mod_asis.c mod_info.c mod_cgi.c mod_negotiation.c mod_dir.c mod_actions.c mod_speling.c mod_userdir.c mod_alias.c mod_rewrite.c mod_so.c One final note - the red hat httpd, apr, and perl packages are all installed, but ldd shows that none of those libraries are linked with the running httpd.

    Read the article

  • Installing vim7 on Solaris Sparc 2.6 as non-root

    - by Tobbe
    I'm trying to install vim to $HOME/bin by compiling the sources. ./configure --prefix=$home/bin seems to work, but when running make I get: > make Starting make in the src directory. If there are problems, cd to the src directory and run make there cd src && make first gcc -c -I. -Iproto -DHAVE_CONFIG_H -DFEAT_GUI_GTK -I/usr/include/gtk-2.0 -I/usr/lib/gtk-2.0/include -I/usr/include/atk-1.0 -I/usr/include/pango-1.0 -I/usr/openwin/include -I/usr/sfw/include -I/usr/sfw/include/freetype2 -I/usr/include/glib-2.0 -I/usr/lib/glib-2.0/include -g -O2 -I/usr/openwin/include -o objects/buffer.o buffer.c In file included from buffer.c:28: vim.h:41: error: syntax error before ':' token In file included from os_unix.h:29, from vim.h:245, from buffer.c:28: /usr/include/sys/stat.h:251: error: syntax error before "blksize_t" /usr/include/sys/stat.h:255: error: syntax error before '}' token /usr/include/sys/stat.h:309: error: syntax error before "blksize_t" /usr/include/sys/stat.h:310: error: conflicting types for 'st_blocks' /usr/include/sys/stat.h:252: error: previous declaration of 'st_blocks' was here /usr/include/sys/stat.h:313: error: syntax error before '}' token In file included from /opt/local/bin/../lib/gcc/sparc-sun-solaris2.6/3.4.6/include/sys/signal.h:132, from /usr/include/signal.h:26, from os_unix.h:163, from vim.h:245, from buffer.c:28: /usr/include/sys/siginfo.h:259: error: syntax error before "ctid_t" /usr/include/sys/siginfo.h:292: error: syntax error before '}' token /usr/include/sys/siginfo.h:294: error: syntax error before '}' token /usr/include/sys/siginfo.h:390: error: syntax error before "ctid_t" /usr/include/sys/siginfo.h:398: error: conflicting types for '__fault' /usr/include/sys/siginfo.h:267: error: previous declaration of '__fault' was here /usr/include/sys/siginfo.h:404: error: conflicting types for '__file' /usr/include/sys/siginfo.h:273: error: previous declaration of '__file' was here /usr/include/sys/siginfo.h:420: error: conflicting types for '__prof' /usr/include/sys/siginfo.h:287: error: previous declaration of '__prof' was here /usr/include/sys/siginfo.h:424: error: conflicting types for '__rctl' /usr/include/sys/siginfo.h:291: error: previous declaration of '__rctl' was here /usr/include/sys/siginfo.h:426: error: syntax error before '}' token /usr/include/sys/siginfo.h:428: error: syntax error before '}' token /usr/include/sys/siginfo.h:432: error: syntax error before "k_siginfo_t" /usr/include/sys/siginfo.h:437: error: syntax error before '}' token In file included from /usr/include/signal.h:26, from os_unix.h:163, from vim.h:245, from buffer.c:28: /opt/local/bin/../lib/gcc/sparc-sun-solaris2.6/3.4.6/include/sys/signal.h:173: error: syntax error before "siginfo_t" In file included from os_unix.h:163, from vim.h:245, from buffer.c:28: /usr/include/signal.h:111: error: syntax error before "siginfo_t" /usr/include/signal.h:113: error: syntax error before "siginfo_t" buffer.c: In function `buflist_new': buffer.c:1502: error: storage size of 'st' isn't known buffer.c: In function `buflist_findname': buffer.c:1989: error: storage size of 'st' isn't known buffer.c: In function `setfname': buffer.c:2578: error: storage size of 'st' isn't known buffer.c: In function `otherfile_buf': buffer.c:2836: error: storage size of 'st' isn't known buffer.c: In function `buf_setino': buffer.c:2874: error: storage size of 'st' isn't known buffer.c: In function `buf_same_ino': buffer.c:2894: error: dereferencing pointer to incomplete type buffer.c:2895: error: dereferencing pointer to incomplete type *** Error code 1 make: Fatal error: Command failed for target `objects/buffer.o' Current working directory /home/xluntor/vim72/src *** Error code 1 make: Fatal error: Command failed for target `first' How do I fix the make errors? Or is there another way to install vim as non-root? Thanks in advance

    Read the article

  • How to find my VPN client IP in windows

    - by cateof
    When I run ipconfig and I get the following: C:\Documents and Settings\grmsrh14>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 112.25.2.222 Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : 112.25.2.1 DHCP Class ID . . . . . . . . . . : rise Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected PPP adapter my_lab: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.2.251.41 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : Is there a command that prints only the my_lab(VPN) IP address, ie 10.2.251.41?

    Read the article

  • Transparent proxy which preserves client mac address

    - by A G
    I have a customer that wants to intercept SSL traffic as it leaves their network. My proposed solution is to setup a proxy that is transparent and both layer 2 and layer 3 so it can simply be dropped into their network without any change in config required. The proxy has two NICs, one connected to the server, the other to the client. The client, proxy and gateway are under control of the customer, the server is not. For example: client --- Proxy --- gateway -|- server I have my proxy program configured with IP_TRANSPARENT socket option to it can respond to connections destined for a remote IP. I am using the following setup: iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 3128 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1 ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 The client in question is on its own subnet and has been configured so that the proxy is the default gateway. The result is: Client sends a frame to the proxy; source IP is client, source mac is client, destination IP is server, destination mac is proxy Proxy forwards this frame to the gateway; source IP is proxy, source mac is proxy, destination IP is server, destination mac is gateway Gateway forwards this to the server and gets a response back. Gateway sends reply back to proxy; source IP is server, source mac is gateway, destination IP is proxy, destination mac is proxy Proxy forwards this reply to client; source IP is server, source mac is proxy, destination IP is client, destination mac is client. The tproxy and iptables configuration lets the proxy send packets with a non local ip address. Is there a way to make something transparent at the mac address level? That is, put the client on the same subnet as the gateway. The gateway sees the source IP and mac as that of the client, even though they originated from the proxy. Could this be done by configuring the proxy as a bridge then use ebtables to escalate the traffic to be handled by iptables? When I use ebtables to push something up to iptables, it appears my proxy program doesn't respond to the packets as they are destined for the gateways's mac address, not the proxy's. What are some other potential avenues I could investigate? EDIT: When the client and gateway are on different subnets (and client has set the proxy as the gateway), it works as described in 1 to 5. But I want to know if it is possible to have the client and gateway on the same subnet and have the proxy fully transparent (ie client is not aware of the proxy). Thanks! EDIT 2: I can configure the proxy as a bridge using brctl, but cannot find a way to direct this traffic to my proxy program - asked here Possible for linux bridge to intercept traffic?. Currently, with the description numbered 1 to 5, it operates at layer 3; it is transparent on the client side (client thinks it is talking to the server's IP), but not on the gateway side (gateway is talking to the proxy's IP). What I want to find out is, is it possible to make this operate at layer 2, so it is fully transparent? What are the available options I should research? Thanks

    Read the article

  • How Hacker Can Access VPS CentOS 6 content?

    - by user2118559
    Just want to understand. Please, correct mistakes and write advices Hacker can access to VPS: 1. Through (using) console terminal, for example, using PuTTY. To access, hacker need to know port number, username and password. Port number hacker can know scanning open ports and try to login. The only way to login as I understand need to know username and password. To block (make more difficult) port scanning, need to use iptables configure /etc/sysconfig/iptables. I followed this https://www.digitalocean.com/community/articles/how-to-setup-a-basic-ip-tables-configuration-on-centos-6 tutorial and got *nat :PREROUTING ACCEPT [87:4524] :POSTROUTING ACCEPT [77:4713] :OUTPUT ACCEPT [77:4713] COMMIT *mangle :PREROUTING ACCEPT [2358:200388] :INPUT ACCEPT [2358:200388] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [2638:477779] :POSTROUTING ACCEPT [2638:477779] COMMIT *filter :INPUT DROP [1:40] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [339:56132] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -p tcp -m tcp ! --tcp-flags FIN,SYN,RST,ACK SYN -m state --state NEW -j DROP -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG FIN,SYN,RST,PSH,ACK,URG -j DROP -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 110 -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m tcp --dport 21 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 21 -j ACCEPT COMMIT Regarding ports that need to be opened. If does not use ssl, then seems must leave open port 80 for website. Then for ssh (default 22) and for ftp (default 21). And set ip address, from which can connect. So if hacker uses other ip address, he can not access even knowing username and password? Regarding emails not sure. If I send email, using Gmail (Send mail as: (Use Gmail to send from your other email addresses)), then port 25 not necessary. For incoming emails at dynadot.com I use Email Forwarding. Does it mean that emails “does not arrive to VPS” (before arriving to VPS, emails are forwarded, for example to Gmail)? If emails does not arrive to VPS, then seems port 110 also not necessary. If use only ssl, must open port 443 and close port 80. Do not understand regarding port 3306 In PuTTY with /bin/netstat -lnp see Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 992/mysqld As understand it is for mysql. But does not remember that I have opened such port (may be when installed mysql, the port is opened automatically?). Mysql is installed on the same server, where all other content. Need to understand regarding port 3306 2. Also hacker may be able access console terminal through VPS hosting provider Control Panel (serial console emergency access). As understand only using console terminal (PuTTY, etc.) can make “global” changes (changes that can not modify with ftp). 3. Hacker can access to my VPS exploiting some hole in my php code and uploading, for example, Trojan. Unfortunately, faced situation that VPS was hacked. As understand it was because I used ZPanel. On VPS ( \etc\zpanel\panel\bin) ) found one php file, that was identified as Trojan by some virus scanners (at virustotal.com). Experimented with the file on local computer (wamp). And appears that hacker can see all content of VPS, rename, delete, upload etc. From my opinion, if in PuTTY use command like chattr +i /etc/php.ini then hacker could not be able to modify php.ini. Is there any other way to get into VPS?

    Read the article

  • vlans on openvz, centos 6

    - by arheops
    i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

    Read the article

  • pptpd not working externally on Ubuntu Server 11.10

    - by Brendan
    I am trying to set up a pptpd vpn on our newly installed Ubuntu 11.10 64 bit server, but am not having success having a client connect via an iPhone to the VPN. Note that no clients have been able to connect to this VPN from outside of the network. The system is up to date with patches. Here is the output of /var/log/syslog. Please note that 222.153.x.y is my remote IP address. Mar 30 22:07:47 server pptpd[9546]: CTRL: Client 222.153.x.y control connection started Mar 30 22:07:47 server pptpd[9546]: CTRL: Starting call (launching pppd, opening GRE) Mar 30 22:07:47 server pppd[9555]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Mar 30 22:07:47 server pppd[9555]: pppd 2.4.5 started by root, uid 0 Mar 30 22:07:47 server pppd[9555]: Using interface ppp0 Mar 30 22:07:47 server pppd[9555]: Connect: ppp0 <--> /dev/pts/3 Mar 30 22:07:47 server pptpd[9546]: GRE: Bad checksum from pppd. Mar 30 22:08:17 server pppd[9555]: LCP: timeout sending Config-Requests Mar 30 22:08:17 server pppd[9555]: Connection terminated. Mar 30 22:08:17 server pppd[9555]: Modem hangup Mar 30 22:08:17 server pppd[9555]: Exit. Mar 30 22:08:17 server pptpd[9546]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Mar 30 22:08:17 server pptpd[9546]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Mar 30 22:08:17 server pptpd[9546]: CTRL: Reaping child PPP[9555] Mar 30 22:08:17 server pptpd[9546]: CTRL: Client 222.153.x.y control connection finished As you can see, the problem seems to be the connection timing out after 30 seconds ("Mar 30 22:08:17 server pppd[9555]: LCP: timeout sending Config-Requests". Over Wifi however (inside the local network) there are no issues: Mar 30 22:12:33 unreal-server pptpd[12406]: CTRL: Client 192.168.0.100 control connection started Mar 30 22:12:33 unreal-server pptpd[12406]: CTRL: Starting call (launching pppd, opening GRE) Mar 30 22:12:33 unreal-server pppd[12407]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Mar 30 22:12:33 unreal-server pppd[12407]: pppd 2.4.5 started by root, uid 0 Mar 30 22:12:33 unreal-server pppd[12407]: Using interface ppp0 Mar 30 22:12:33 unreal-server pppd[12407]: Connect: ppp0 <--> /dev/pts/3 Mar 30 22:12:33 unreal-server pptpd[12406]: GRE: Bad checksum from pppd. Mar 30 22:12:36 unreal-server pppd[12407]: peer from calling number 192.168.0.100 authorized Mar 30 22:12:36 unreal-server pppd[12407]: MPPE 128-bit stateless compression enabled Mar 30 22:12:36 unreal-server pppd[12407]: Cannot determine ethernet address for proxy ARP Mar 30 22:12:36 unreal-server pppd[12407]: local IP address 192.168.0.10 Mar 30 22:12:36 unreal-server pppd[12407]: remote IP address 192.168.1.1 I have set up an iptables config for the server; to check this isn't the problem I allowed all traffic temporarily, but this does NOT change the symptoms in the first example. Here is the output from /etc/iptables.rules.save *filter :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT Even with these rules applied, the output from /var/log/syslog is LINE FOR LINE what I saw in the the first block of code. Please note that before running this Ubuntu server; an old SME Server box was running in place of it, that had a pptpd server on it just like we are using, and we experienced no issues.

    Read the article

  • VirtualServer reverseproxy works locally, but not from client

    - by Yep
    Setup: 2 Webservers pointed to 127.0.0.1:8080 and :8081. Curl validates they work as expected. Apache with the following virt hosts: NameVirtualHost 192.168.1.1:80 <VirtualHost 192.168.1.1:80> ServerAdmin [email protected] ProxyPass / http://127.0.0.1:8080/ ProxyPassReverse / http://127.0.0.1:8080/ ServerName 192.168.1.1 ServerAlias http://192.168.1.1 </VirtualHost> NameVirtualHost 192.168.1.2:80 <VirtualHost 192.168.1.2:80> ServerAdmin [email protected] ProxyPass / http://127.0.0.1:8081/ ProxyPassReverse / http://127.0.0.1:8081/ ServerName 192.168.1.2 ServerAlias http://192.168.1.2 </VirtualHost> On the server I can curl to the virtualhosts and receive appropriate responses. (curl 192.168.1.1 gives me the webservers response from localhost:8080, etc) remote hosts cannot however connect to 192.168.1.1 or .2 at all. What am I missing? Re: comments Yes, the default directory Directive is still in place. # Deny access to root file system <Directory /> Options None AllowOverride None Order Deny,Allow deny from all </Directory> No apache logs are generated when trying to reach 192.168.1.1 remotely. They do get generated when curl from local. If I point the webservers to *:8080 and *:8081 instead of binding to localhost, I can access them from a remote host via 192.168.1.1 and 192.168.1.2 if i specify the 8080 and 8081 ports (both ports work on both IP's, which is what I'm trying to avoid with apache reverse proxy bind to 80 on each interface) Edit2: curl verbose output: (similar for second webserver, and for 127.0.0.1:portnum) [user@host mingle_12_2_1]$ curl -v 192.168.1.1 * About to connect() to 192.168.1.1 port 80 * Trying 192.168.1.1... connected * Connected to 192.168.1.1 (192.168.1.1) port 80 > GET / HTTP/1.1 > User-Agent: curl/7.15.5 (x86_64-redhat-linux-gnu) libcurl/7.15.5 OpenSSL/0.9.8b zlib/1.2.3 libidn/0.6.5 > Host: 192.168.1.1 > Accept: */* > < HTTP/1.1 302 Found < Date: Tue, 16 Oct 2012 16:22:08 GMT < Server: Jetty(6.1.19) < Cache-Control: no-cache < Location: http://192.168.1.1/install < X-Runtime: 130 < Content-Type: text/html; charset=utf-8 < Content-Length: 94 < Connection: close Closing connection #0 <html><body>You are being <a href="http://192.168.1.1/install">redirected</a>.</body></html> log from the request local 192.168.1.1 - - [16/Oct/2012:12:22:08 -0400] "GET / HTTP/1.1" 302 94 no apache access log or error log generated when requests from remote clients.

    Read the article

  • Forwarding rsyslog to syslog-ng, with FQDN and facility separation

    - by Joshua Miller
    I'm attempting to configure my rsyslog clients to forward messages to my syslog-ng log repository systems. Forwarding messages works "out of the box", but my clients are logging short names, not FQDNs. As a result the messages on the syslog repo use short names as well, which is a problem because one can't determine which system the message originated from easily. My clients get their names through DHCP / DNS. I've tried a number of solutions trying to get this working, but without success. I'm using rsyslog 4.6.2 and syslog-ng 3.2.5. I've tried setting $PreserveFQDN on as the first directive in /etc/rsyslog.conf (and restarting rsyslog of course). It seems to have no effect. hostname --fqdn on the client returns the proper FQDN, so the problem isn't whether the system can actually figure out its own FQDN. $LocalHostName <fqdn> looked promising, but this directive isn't available in my version of rsyslog (Available since 4.7.4+, 5.7.3+, 6.1.3+). Upgrading isn't an option at the moment. Configuring the syslog-ng server to populate names based on reverse lookups via DNS isn't an option. There are complexities with reverse DNS and the public cloud. Specifying for the forwarder to use a custom template seems like a viable option at first glance. I can specify the following, which causes local logging to begin using the FQDN on the syslog-ng repo. $template MyTemplate, "%timestamp% <FQDN> %syslogtag%%msg%" $ActionForwardDefaultTemplate MyTemplate However, when I put this in place syslog-ng seems to be unable to categorize messages by facility or priority. Messages come in as FQDN, but everything is put in to user.log. When I don't use the custom template, messages are properly categorized under facility and priority, but with the short name. So, in summary, if I manually trick rsyslog into including the FQDN, priority and facility becomes lost details to syslog-ng. How can I get rsyslog to do FQDN logging which works properly going to a syslog-ng repository? rsyslog client config: $ModLoad imuxsock.so # provides support for local system logging (e.g. via logger command) $ModLoad imklog.so # provides kernel logging support (previously done by rklogd) $ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat *.info;mail.none;authpriv.none;cron.none /var/log/messages authpriv.* /var/log/secure mail.* -/var/log/maillog cron.* /var/log/cron *.emerg * uucp,news.crit /var/log/spooler local7.* /var/log/boot.log $WorkDirectory /var/spool/rsyslog # where to place spool files $ActionQueueFileName fwdRule1 # unique name prefix for spool files $ActionQueueMaxDiskSpace 1g # 1gb space limit (use as much as possible) $ActionQueueSaveOnShutdown on # save messages to disk on shutdown $ActionQueueType LinkedList # run asynchronously $ActionResumeRetryCount -1 # infinite retries if host is down *.* @syslog-ng1.example.com *.* @syslog-ng2.example.com syslog-ng configuration (abridged for brevity): options { flush_lines (0); time_reopen (10); log_fifo_size (1000); long_hostnames (off); use_dns (no); use_fqdn (yes); create_dirs (no); keep_hostname (yes); }; source src { unix-stream("/dev/log"); internal(); udp(ip(0.0.0.0) port(514)); }; destination per_host_destination { file( "/var/log/syslog-ng/devices/$HOST/$FACILITY.log" owner("root") group("root") perm(0644) dir_owner(root) dir_group(root) dir_perm(0775) create_dirs(yes)); }; log { source(src); destination(per_facility_destination); };

    Read the article

  • Installation of Access Database Engine 32-bit Fails

    - by Rayzor78
    I am trying to install Access Database Engine 2007 32-bit. The splash screen comes up, you click "Next", then it fails with the error: Installation ended prematurely because of an error You click "OK" and another error window says: The installation of the package failed. The exact same situation happens when I try this with Access Database Engine 2010 32-bit. This production server is running Windows Server 2008 R2 SP1 64-bit. Before I tried installing Access Database Engine 32-bit, I first needed to install Microsoft Office 2010 Pro (Excel and Office Tools only). I tried the 32-bit version on the production server since that is how I set it up in our Dev environment. No luck. The 32-bit version would not install. I did NOT get the error "You have 64-bit components of Office installed". I simply received the exact same two errors listed above. So, I knew that 32-bit/64-bit did not really matter for the Office install for my project, so I installed 64-bit of Office Pro 2010 (Excel and Office Tools only) with no problems. I have a requirement that I need to have the 32-bit version of the Access Database Engine installed. 2007 or 2010, doesn't matter. I cannot use the 64-bit version of Access Database Engine 2010 because my SSIS package will not work with it. I require the 32-bit version. I've tried several steps to try to get it installed. I seriously think that the production server has some aversion to installing 32-bit applications. Here's what I've tried: Tried installing via command line with the "/passive" switch....no luck. Tried numerous iterations to copy the install file to the server (downloaded a fresh copy directly to the server, downloaded a fresh copy to my local machine then copied it over, copied it over zipped up) (http://social.msdn.microsoft.com/Forums/en-US/sqldataaccess/thread/efd3c1f0-07cd-45ca-a626-2dd0c7ac3e9f). Tried Method 1 from this link. Could not try Method 2 because it requires a server reboot and in my environment that requires a long change management process. I've verified that I am a local administrator on the server. (Evidence, I am able to install other applications (office 64-bit per above)). Verified that there are no other office products that should be blocking the installation. The fore-mentioned install of Excel 2010 64-bit was the first Office product installed on the server. VERY ODD: To test my theory that the production server does not like 32-bit applications, I installed something lightweight. I installed 7-Zip 32-bit on the production server with no problems whatsoever. Here are some things that I have not tried (i will follow-up once I do): Method 2 (as mentioned above). Requires a server reboot. Have not verified that the Dev and Production environments are 100% identical. I've done a cursory check and on the surface they appear to be the same (same OS and SP version). I need to do a deeper dive to be 100% certain. I had no problems in my Dev environment. In Dev, I installed Office 2010 Pro 64-bit (Excel & Office Tools only) then via command line w/ the "/passive" switch, installed Access Database Engine 2010 32-bit. I don't know what else to try. Any suggestions or comments?

    Read the article

  • how to troubleshoot using rsyslog to output to a mysql database

    - by ChrisNZ
    Using FreeBSD 8.0 32 bit. I have installed rsyslogd 5.5.5 with ommysql. (installed ports /usr/ports/sysutils/rsyslog55 and /usr/ports/sysutils/rsyslog55-mysql) My rsyslog.conf file looks like: $ModLoad imudp $ModLoad imtcp $ModLoad ommysql $ModLoad immark.so $ModLoad imuxsock.so $ModLoad imklog.so $OptimizeForUniprocessor on $AllowedSender UDP, 10.0.0.0/8 $UDPServerAddress 0.0.0.0 $UDPServerRun 514 $UDPServerTimeRequery 2 # +SG560 *.* :ommysql:127.0.0.1,Syslog,sysloguser,mypassword My command line flags for rsyslogd are: -c5 -4 Checking the code with -c5 -N1 returns no errors. I have confirmed that rsyslogd is working by changing the last line to say: *.* /var/log/snapgear.log which results in messages appearing in the snapgear.log file. So it is probably something to do with my MySQL setup If I do: mysql -u sysloguser -p Syslog Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 56 Server version: 5.0.86 FreeBSD port: mysql-server-5.0.86 mysql> select * from SystemEvents; Empty set (0.00 sec) mysql> :-( I have confirmed that sysloguser has full privileges for the Syslog database. If I run rsyslogd on the console in debug mode: /usr/local/sbin/rsyslogd -f /usr/local/etc/rsyslog.conf -c5 -n -d I can see this sequence of events each time a message is received: 9244.376687256:28359280: main Q: entry added, size now log 1, phys 1 entries 9244.376705694:28359280: main Q: EnqueueMsg advised worker start 9244.376726647:28359280: Listening on UDP syslogd socket 4 (IPv4/port 514). 9244.376728602:28359280: --------imUDP calling select, active file descriptors (max 4): 4 9244.376890075:283593c0: wti 0x28306e80: worker awoke from idle processing 9244.376892031:283593c0: we deleted 0 objects and enqueued 0 objects 9244.376893986:283593c0: delete batch from store, new sizes: log 1, phys 1 9244.376895942:283593c0: msgConsumer processes msg 0/1 9244.376897898:283593c0: msg parser: flags 70, from '~NOTRESOLVED~', msg 'Jun 29 17:32:24 SG560 kernel: (20000629T1732244' 9244.376900132:283593c0: parse using parser list 0x283080e8 (the default list). 9244.376902088:283593c0: dropped LF at very end of message (DropTrailingLF is set) 9244.376904044:283593c0: Parser 'rsyslog.rfc5424' returned -2160 9244.376905999:283593c0: Message will now be parsed by the legacy syslog parser (one size fits all... ;)). 9244.376907955:283593c0: Parser 'rsyslog.rfc3164' returned 0 9244.376909910:283593c0: testing filter, f_pmask 255 9244.376911866:283593c0: Called action, logging to ommysql 9244.376918012:283593c0: actionTryResume: action state: susp, next retry (if applicable): 1277869250 [now 1277869244] 9244.376919967:283593c0: action call returned -2123 9244.376921923:283593c0: tryDoAction: unexpected error code -2123, finalizing 9244.376926113:283593c0: actionTryResume: action state: susp, next retry (if applicable): 1277869250 [now 1277869244] 9244.376928069:283593c0: ruleset: get iRet 0 from rule.ProcessMsg() 9244.376930024:283593c0: ruleset.ProcessMsg() returns 0 9244.376931980:283593c0: regular consumer finished, iret=0, szlog 0 sz phys 1 9244.376933936:283593c0: XXX: enqueueing data element 0 of 1 9244.376935891:283593c0: we deleted 1 objects and enqueued 0 objects 9244.376938126:283593c0: delete batch from store, new sizes: log 0, phys 0 9244.376940082:283593c0: regular consumer finished, iret=4, szlog 0 sz phys 0 9244.376942037:283593c0: main Q:Reg/w0: worker IDLE, waiting for work. .... I can see the Action Call to ommysql returns unexpected error code -2123 Now I am stuck! Any ideas on what to look for next? Perhaps I there are extra ports I need to install? I will be very grateful for any assistance here!

    Read the article

  • How can I check if PHP was compiled with the UNICODE version of the Win32 API?

    - by Wesley Murch
    This is related to this Stack Overflow post: glob() can't find file names with multibyte characters on Windows? I'm having issues with PHP and files that have multibyte characters on Windows. Here's my test case: print_r(scandir('./uploads/')); print_r(glob('./uploads/*')); Correct Output on remote UNIX server: Array ( [0] => . [1] => .. [2] => filename-äöü.jpg [3] => filename.jpg [4] => test?test.jpg [5] => ??? ?????.jpg [6] => ?????????.jpg [7] => ???.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg [2] => ./uploads/test?test.jpg [3] => ./uploads/??? ?????.jpg [4] => ./uploads/?????????.jpg [5] => ./uploads/???.jpg ) Incorrect Output locally on Windows: Array ( [0] => . [1] => .. [2] => ??? ?????.jpg [3] => ???.jpg [4] => ?????????.jpg [5] => filename-äöü.jpg [6] => filename.jpg [7] => test?test.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg ) Here's a relevant excerpt from the answer I chose to accept (which actually is a quote from an article that was posted online over 2 years ago): From the comments on this article: http://www.rooftopsolutions.nl/blog/filesystem-encoding-and-php The output from your PHP installation on Windows is easy to explain : you installed the wrong version of PHP, and used a version not compiled to use the Unicode version of the Win32 API. For this reason, the filesystem calls used by PHP will use the legacy "ANSI" API and so the C/C++ libraries linked with this version of PHP will first try to convert yout UTF-8-encoded PHP string into the local "ANSI" codepage selected in the running environment (see the CHCP command before starting PHP from a command line window) Your version of Windows is MOST PROBABLY NOT responsible of this weird thing. Actually, this is YOUR version of PHP which is not compiled correctly, and that uses the legacy ANSI version of the Win32 API (for compatibility with the legacy 16-bit versions of Windows 95/98 whose filesystem support in the kernel actually had no direct support for Unicode, but used an internal conversion layer to convert Unicode to the local ANSI codepage before using the actual ANSI version of the API). Recompile PHP using the compiler option to use the UNICODE version of the Win32 API (which should be the default today, and anyway always the default for PHP installed on a server that will NEVER be Windows 95 or Windows 98...) I can't confirm whether this is my problem or not. I used phpinfo() and did not find anything interesting, but I wasn't sure what to look for. I've been using XAMPP for easy installations, so I'm really not sure exactly how it was installed. I'm using Windows 7, 64 bit - so forgive my ignorance, but I'm not even sure if "Win32" is relevant here. How can I check if my current version of PHP was compiled with the configuration mentioned above? PHP Version: 5.3.8 System: Windows NT WES-PC 6.1 build 7601 (Windows 7 Home Premium Edition Service Pack 1) i586 Build Date: Aug 23 2011 11:47:20 Compiler: MSVC9 (Visual C++ 2008) Architecture: x86 Configure Command: cscript /nologo configure.js "--enable-snapshot-build" "--disable-isapi" "--enable-debug-pack" "--disable-isapi" "--without-mssql" "--without-pdo-mssql" "--without-pi3web" "--with-pdo-oci=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8-11g=D:\php-sdk\oracle\instantclient11\sdk,shared" "--enable-object-out-dir=../obj/" "--enable-com-dotnet" "--with-mcrypt=static" "--disable-static-analyze"

    Read the article

  • Set up lnux box for hosting a-z [apache mysql php ssl]

    - by microchasm
    I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure Virtualhosts for SSL, setting up a CA, setting up SFTP with openSSH, or anything else would be appreciated.

    Read the article

  • libvirt upgrade caused vms to not see drives (boot media not found)

    - by bias
    I upgraded to Ubuntu 12.04.1 and now libvirt (via open nebula) successfully runs vms but they aren't finding the 2 drives (specifically, the boot drive). One is "hd" the other is "cdrom". The machine boots but fails and displays something like "boot media not found hd" (this was in a vnc terminal and I didn't copy the output anywhere so that's not the verbatim message). I tried constructing a new disk using the new version of qemu (via vmbuilder) and this new machine has the same problem as the old machine. In case it matters (I can't see why it would) I'm using open nebula to manage the machines. There's nothing relevant in any of the logs: syslog, libvirtd, oned. Which is to say nothing interesting/anomalous is reported when the machine is brought up. Versions libvirt 0.9.8-2ubuntu17.4 qemu-kvm 1.0+noroms-0ubuntu14.3 The libvirt xml config portions (relavent) <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> ... <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='qcow2'/> <source file='/var/lib/one//203/images/disk.0'/> <target dev='sda' bus='scsi'/> <alias name='scsi0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/var/lib/one//203/images/disk.1'/> <target dev='sdc' bus='scsi'/> <readonly/> <alias name='scsi0-0-2'/> <address type='drive' controller='0' bus='0' unit='2'/> </disk> <controller type='scsi' index='0'> <alias name='scsi0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </controller> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </memballoon> ... </devices> The libvirt/qemu log contains 2012-11-25 22:19:24.328+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 256 -smp 1,sockets=1,cores=1,threads=1 -name one-204 -uuid 4be6c276-19e8-bdc2-e9c9-9ca5352f2be3 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/one-204.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -device lsi,id=scsi0,bus=pci.0,addr=0x5 -drive file=/var/lib/one//204/images/disk.0,if=none,id=drive-scsi0-0-0,format=qcow2 -device scsi-disk,bus=scsi0.0,scsi-id=0,drive=drive-scsi0-0-0,id=scsi0-0-0,bootindex=1 -drive file=/var/lib/one//204/images/disk.1,if=none,media=cdrom,id=drive-scsi0-0-2,readonly=on,format=raw -device scsi-disk,bus=scsi0.0,scsi-id=2,drive=drive-scsi0-0-2,id=scsi0-0-2 -netdev tap,fd=18,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3 -netdev tap,fd=19,id=hostnet1 -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4 -usb -vnc 0.0.0.0:204 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x6 kvm: -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom" kvm: -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom"

    Read the article

  • Ubuntu Server, 2 Ethernet Devices, Same Gateway - Want to force internet traffic through 1 device (or at least allow it to work!)

    - by Chris Drumgoole
    I have a Ubuntu 10.04 Server with 2 ethernet devices, eth0 and eth1. eth0 has a static IP of 192.168.1.210 eth1 has a static IP if 192.168.1.211 The DHCP server (which also serves as the internet gateway) sits at 192.168.1.1. The issue I have right now is when I have both plugged in, I can connect to both IPs over SSH internally, but I can't connect to the internet from the server. If I unplug one of the devices (e.g. eth1), then it works, no problem. (Also, I get the same result when I run sudo ifconfig eth1 down). Question, how can I configure it so that I can have both devices eth0 and eth1 play nice on the same network, but allow internet access as well? (I am open to either enforcing all inet traffic going through a single device, or through both, I'm flexible). From my google searching, it seems I could have a unique (or not popular) problem, so haven't been able to find a solution. Is this something that people generally don't do? The reason I want to make use of both ethernet devices is because I want to run different local traffic services on on both to split the load, so to speak... Thanks in advance. UPDATE Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The secondary network interface #auto eth1 #iface eth1 inet dhcp (Note: above, I commented out the last 2 lines because I thought that was causing issues... but it didn't solve it) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 192.168.1.1 255.255.255.0 UG 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 UPDATE 2 I made a change to the /etc/network/interfaces file as suggested by Kevin. Before I display the file contents and the route table, when I am logged into the server (through SSH), I can not ping an external server, so this is the same issue I was experiencing that led to me posting this question. I ran a /etc/init.d/networking restart after making the file changes. Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp address 192.168.1.210 netmask 255.255.255.0 gateway 192.168.1.1 # The secondary network interface auto eth1 iface eth1 inet dhcp address 192.168.1.211 netmask 255.255.255.0 ifconfig output eth0 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:7f inet addr:192.168.1.210 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:27f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6397 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:538881 (538.8 KB) TX bytes:85597 (85.5 KB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:80 inet addr:192.168.1.211 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:280/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5799 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:484436 (484.4 KB) TX bytes:1184 (1.1 KB) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:635 errors:0 dropped:0 overruns:0 frame:0 TX packets:635 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:38154 (38.1 KB) TX bytes:38154 (38.1 KB) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • Set source address to use tun device does not work (Debian Squeeze)

    - by A. Donda
    there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

    Read the article

  • Log transport and aggregation at scale

    - by markdrayton
    How're you analysing log files from UNIX/Linux machines? We run several hundred servers which all generate their own log files, either directly or through syslog. I'm looking for a decent solution to aggregate these and pick out important events. This problem breaks down into 3 components: 1) Message transport The classic way is to use syslog to log messages to a remote host. This works fine for applications that log into syslog but less useful for apps that write to a local file. Solutions for this might include having the application log into a FIFO connected to a program to send the message using syslog, or by writing something that will grep the local files and send the output to the central syslog host. However, if we go to the trouble of writing tools to get messages into syslog would we be better replacing the whole lot with something like Facebook's Scribe which offers more flexibility and reliability than syslog? 2) Message aggregation Log entries seem to fall into one of two types: per-host and per-service. Per-host messages are those which occur on one machine; think disk failures or suspicious logins. Per-service messages occur on most or all of the hosts running a service. For instance, we want to know when Apache finds an SSI error but we don't want the same error from 100 machines. In all cases we only want to see one of each type of message: we don't want 10 messages saying the same disk has failed, and we don't want a message each time a broken SSI is hit. One approach to solving this is to aggregate multiple messages of the same type into one on each host, send the messages to a central server and then aggregate messages of the same kind into one overall event. SER can do this but it's awkward to use. Even after a couple of days of fiddling I had only rudimentary aggregations working and had to constantly look up the logic SER uses to correlate events. It's powerful but tricky stuff: I need something which my colleagues can pick up and use in the shortest possible time. SER rules don't meet that requirement. 3) Generating alerts How do we tell our admins when something interesting happens? Mail the group inbox? Inject into Nagios? So, how're you solving this problem? I don't expect an answer on a plate; I can work out the details myself but some high-level discussion on what is surely a common problem would be great. At the moment we're using a mishmash of cron jobs, syslog and who knows what else to find events. This isn't extensible, maintainable or flexible and as such we miss a lot of stuff we shouldn't. Updated: we're already using Nagios for monitoring which is great for detected down hosts/testing services/etc but less useful for scraping log files. I know there are log plugins for Nagios but I'm interested in something more scalable and hierarchical than per-host alerts.

    Read the article

  • How broken is routing strategy that causes a martian packet (so far only) during tracepath?

    - by lkraav
    I believe I've achieved a table that routes packets from and to eth1/192.168.3.x through 192.168.3.1, and packets from and to eth0/192.168.1.x through 192.168.1.1 (helpful source). Question: when doing tracepath from 192.168.3.20 (from within vserver), I'm getting kernel: [318535.927489] martian source 192.168.3.20 from 212.47.223.33, on dev eth0 at or near the target IP, while intermediary hops go without (log below). I don't understand why this packet is arriving on eth0, instead of eth1, even after reading this: Note that you may see packets from non-routable IP addresses when running the traceroute or tracepath commands. While packets cannot be routed to these routers, packets sent between 2 routers only need to know the address of the next hop within the local networks, which could be a non-routable address. Can someone explain that paragraph in human language? Based on short initial trials so far, everything else seems to work without causing martians. Is this contained to the nature of tracepath operation or do I have some other bigger routing problem that will cause work traffic breakage? Side note: is it possible to inspect martian packet with tcpdump or wireshark or anything of the sort? I'm have not been able to get it to show up on my own. vserver-20 / # tracepath -n 212.47.223.33 1: 192.168.3.2 0.064ms pmtu 1500 1: 192.168.3.1 1.076ms 1: 192.168.3.1 1.259ms 2: 90.191.8.2 1.908ms 3: 90.190.134.194 2.595ms 4: 194.126.123.94 2.136ms asymm 5 5: 195.250.170.22 2.266ms asymm 6 6: 212.47.201.86 2.390ms asymm 7 7: no reply 8: no reply 9: no reply ^C Host routing: $ sudo ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:24:1d:de:b3:5d brd ff:ff:ff:ff:ff:ff inet 192.168.1.2/24 scope global eth0 4: eth1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:46:46:a3:6a brd ff:ff:ff:ff:ff:ff inet 192.168.3.2/27 scope global eth1 inet 192.168.3.20/27 brd 192.168.3.31 scope global secondary eth1 # linux-vserver instance $ sudo ip route default via 192.168.1.1 dev eth0 metric 3 unreachable 127.0.0.0/8 scope host 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.2 192.168.3.0/27 dev eth1 proto kernel scope link src 192.168.3.2 $ sudo ip rule 0: from all lookup local 32764: from all to 192.168.3.0/27 lookup dmz 32765: from 192.168.3.0/27 lookup dmz 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table dmz default via 192.168.3.1 dev eth1 metric 4 192.168.3.0/27 dev eth1 scope link metric 4 Gateway routing # ip route 10.24.0.2 dev tun0 proto kernel scope link src 10.24.0.1 10.24.0.0/24 via 10.24.0.2 dev tun0 192.168.3.0/24 dev br-dmz proto kernel scope link src 192.168.3.1 192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1 $ISP_NET/23 dev eth0.1 proto kernel scope link src $WAN_IP default via $ISP_GW dev eth0.1 Additional background Options for non-virtualized network interface isolation?

    Read the article

  • VS 2010 debugger not loading symbols when attaching to NUnit

    - by Dave Hanna
    (I just posted this in the NUnit discussion group on groups.google.com) Under VS 2008, I would run my tests under NUnit, and, if I needed to debug, I would attach the VS2008 debugger to the running Nunit process (Debug - Attach to Process), and set any breakpoints on code I wanted to examine. When I hit the Run buttion in NUnit, it would hit the breakpoint. (BTW, if it matters, this was running NUnit 2.5.2). I just upgraded to NUnit 2.5.4 and VS 2010. When I set a breakpoint, then attach to NUnit, I get a little warning symbol on the breakpoint dot, and hovering over it gives the tooltip "Breakpoint will not be hit. No symbols are currently loaded". Going to the Debug - Windows - Modules window shows a whole bunch of Windows and NUnit modules loaded, with the Symbol Status of "Skipped loading symbols", and then 1 module with a funny name that changes each time (r1euhmh5 right now), and Symbol Status of "No symbols loaded". (There is no trace of a module with a name remotely like my DLL under test). Right clicking the funny filename (assuming that to be some mapping from my DLL under test), and clicking Load Symbols From - Symbol Path, and navigating to the bin\debug folder, then clicking the pdb file of my DLL under test, I get the message "A matching symbol was not found in this folder". (The top of the Open dialog box has a line that says "Original location: r1euhmh5.pdb") So what's changed? And how do I go about debugging/breakpointing under VS 2010/NUnit 2.5.4 (Or is it possible I screwed something up when I decided to go through my VS2010 options and set some of them to more advanced levels than I knew what I was doing?) I appreciate any help.

    Read the article

  • Spring security custom ldap authentication provider

    - by wuntee
    I currently have my ldap authentication context set up like this: <ldap-server url="ldap://host/dn" manager-dn="cn=someuser" manager-password="somepass" /> <authentication-manager> <ldap-authentication-provider user-search-filter="(samaccountname={0})"/> </authentication-manager> Now, I need to be able to set up a custom authorities mapper (it uses a different ldap server) - so I am assuming I need to set up my ldap-server similar to (http://static.springsource.org/spring-security/site/docs/2.0.x/reference/ldap.html): <bean id="ldapAuthProvider" class="org.springframework.security.providers.ldap.LdapAuthenticationProvider"> <constructor-arg> <bean class="org.springframework.security.providers.ldap.authenticator.BindAuthenticator"> <constructor-arg ref="contextSource"/> <property name="userDnPatterns"> <list><value>uid={0},ou=people</value></list> </property> </bean> </constructor-arg> <constructor-arg> <bean class="org.springframework.security.ldap.populator.DefaultLdapAuthoritiesPopulator"> <constructor-arg ref="contextSource"/> <constructor-arg value="ou=groups"/> <property name="groupRoleAttribute" value="ou"/> </bean> </constructor-arg> </bean> But, how do I reference that 'ldapAuthProvider' to the ldap-server in the security context? I am also using spring-security 3, so '' does not exist...

    Read the article

  • How to Link VS2010 Database Project and LINQ to SQL

    - by Jason
    As I am working with the new database projects in VS2010, and as I am learning LINQ to SQL, I am curious as to the best way to link the two groups of information so that when I update one, the other updates along with it. From my research here at SO, as well as in Google, it appears the general rule of thumb is: "Build the database, and then create your LINQ to SQL classes." Of course, if I make a change in my database, the LINQ to SQL doesn't update automatically and I have to do it by hand. This is fairly simple right now as my database is small, but I am curious if there is an easier way for this to happen. In addition, the LINQ to SQL tool is pretty nice. The ability to create tables, add associations, and even create inheritance is very simple. As my second question, I am curious as to whether or not VS2010 can work the other way - I design the database in the DBLM file and then link it back to my database project. I appreciate any help with either of these two questions. I'm really interested in making this as easy as possible to reduce errors during development and improve the speed at which changes can be made.

    Read the article

  • Fancybox Auto Close, but remain user control

    - by justinw
    Hi, i've searched through the forum yet i can't find the solution. i'm refering to this thread to do the auto close function: http://groups.google.com/group/fancybox/browse_thread/thread/d09438b7... I did follow JFK's solution which works just right: 'onComplete': function() { $("#fancybox-wrap, #fancybox-overlay").delay(3000).fadeOut(); } if you don't want the user to close the box, then add modal=true The scenario is I would like the user to have the option to close the modal when they click on the [close] button or click anywhere on the overlay. I'm using the latest version of FB and jQuery on Rails. Here's my script: <script type="text/javascript"> jQuery(document).ready(function() { jQuery("#link_post").fancybox({ 'autoDimensions':false, 'width':380, 'height':50, 'title':'This message box will automatically close in 10 seconds.', 'titlePosition':'outside', 'onComplete': function() { jQuery("#fancybox-wrap, #fancybox- overlay").delay(10000).fadeOut(); } }); }); </script> However, when i clicked on the close button, the title and close button will fade away, but the FB's content and overlay are still there! it will only fade away after 10 seconds. So, my question is how to overwrite the 'onComplete' function if user clicks on the close button before it automatically closes?

    Read the article

  • Common vulnerabilities for WinForms applications

    - by David Stratton
    I'm not sure if this is on-topic or not here, but it's so specific to .NET WinForms that I believe it makes more sense here than at the Security stackexchange site. (Also, it's related strictly to secure coding, and I think it's as on-topic as any question asking about common website vulnerabiitles that I see all over the site.) For years, our team has been doing threat modeling on Website projects. Part of our template includes the OWASP Top 10 plus other well-known vulnerabilities, so that when we're doing threat modeling, we always make sure that we have a documented process to addressing each of those common vulnerabilities. Example: SQL Injection (Owasp A-1) Standard Practice Use Stored Parameterized Procedures where feasible for access to data where possible Use Parameterized Queries if Stored Procedures are not feasible. (Using a 3rd party DB that we can't modify) Escape single quotes only when the above options are not feasible Database permissions must be designed with least-privilege principle By default, users/groups have no access While developing, document the access needed to each object (Table/View/Stored Procedure) and the business need for access. [snip] At any rate, we used the OWASP Top 10 as the starting point for commonly known vulnerabilities specific to websites. (Finally to the question) On rare occasions, we develop WinForms or Windows Service applications when a web app doesn't meet the needs. I'm wondering if there is an equivalent list of commonly known security vulnerabilities for WinForms apps. Off the top of my head, I can think of a few.... SQL Injection is still a concern Buffer Overflow is normally prevented by the CLR, but is more possible if using non-managed code mixed in with managed code .NET code can be decompiled, so storing sensitive info in code, as opposed to encrypted in the app.config... Is there such a list, or even several versions of such a list, from which we can borrow to create our own? If so, where can I find it? I haven't been able to find it, but if there is one, it would be a great help to us, and also other WinForms developers.

    Read the article

  • How to associate jquery validation with only one button if there are many?

    - by Eyla
    Greetings, In my current project, I have gridview, search button, text box for search, text box, and submit button. -I should input string in the search box then click search button. -when click search button, it will retrieve all matches records then bind them to the view grid. -then when I click a record in the gridview, it should bound a field to the second text box. finally I should submit the page by clicking in submit button. where is the problem: -the problme that I'm using jquery validation plugin that will make second text box is required. -when I click search button will not allow postback until I write some thing in second text box. How can I make scond text box only do validation for required field only when click asp.net submit button. here is my code: <%@ Page Title="" Language="C#" MasterPageFile="~/Master.Master" AutoEventWireup="true" CodeBehind="WebForm1.aspx.cs" Inherits="IMAM_APPLICATION.WebForm1" %> <%@ Register Assembly="AjaxControlToolkit" Namespace="AjaxControlToolkit" TagPrefix="cc1" %> <asp:Content ID="Content1" ContentPlaceHolderID="ContentPlaceHolder1" runat="server"> <script src="js/jquery-1.4.1-vsdoc.js" type="text/javascript"></script> <script src="js/jquery.validate.js" type="text/javascript"></script> <script src="js/js.js" type="text/javascript"></script> <script type="text/javascript"> $(document).ready(function() { $("#aspnetForm").validate({ // debug: true, rules: { "<%=txtFirstName.UniqueID %>": { required: true } }, errorElement: "mydiv", wrapper: "mydiv", // a wrapper around the error message errorPlacement: function(error, element) { offset = element.offset(); error.insertBefore(element) error.addClass('message'); // add a class to the wrapper error.css('position', 'absolute'); error.css('left', offset.left + element.outerWidth()); error.css('top', offset.top - (element.height() / 2)); } }); }) </script> <div id="mydiv"> <asp:GridView ID="GridView1" runat="server" style="position:absolute; top: 280px; left: 30px; height: 240px; width: 915px;" PageSize="5" onselectedindexchanged="GridView1_SelectedIndexChanged" AutoGenerateColumns="False" DataKeyNames="idcontact_info"> <Columns> <asp:CommandField ShowSelectButton="True" InsertVisible="False" ShowCancelButton="False" /> <asp:BoundField DataField="First_Name" HeaderText="First Name" /> <asp:BoundField AccessibleHeaderText="Midle Name" DataField="Midle_Name" /> <asp:BoundField DataField="Last_Name" HeaderText="Last Name" /> <asp:BoundField DataField="Phone_home" HeaderText="Phone Home" /> <asp:BoundField DataField="cell_home" HeaderText="Mobile Home" /> <asp:BoundField DataField="phone_work" HeaderText="Phone Work" /> <asp:BoundField DataField="cell_Work" HeaderText="Mobile Work" /> <asp:BoundField DataField="Email_Home" HeaderText="Personal Home" /> <asp:BoundField DataField="Email_work" HeaderText="Work Email" /> </Columns> </asp:GridView> <asp:ObjectDataSource ID="ObjectDataSource1" runat="server" DeleteMethod="Delete" InsertMethod="Insert" OldValuesParameterFormatString="original_{0}" SelectMethod="GetData" TypeName="IMAM_APPLICATION.DSContactTableAdapters.contact_infoTableAdapter" UpdateMethod="Update"> <DeleteParameters> <asp:Parameter Name="Original_idcontact_info" Type="Int32" /> </DeleteParameters> <UpdateParameters> <asp:Parameter Name="Title" Type="String" /> <asp:Parameter Name="First_Name" Type="String" /> <asp:Parameter Name="Midle_Name" Type="String" /> <asp:Parameter Name="Last_Name" Type="String" /> <asp:Parameter Name="Address1_Home" Type="String" /> <asp:Parameter Name="Address2_Home" Type="String" /> <asp:Parameter Name="City_Home" Type="String" /> <asp:Parameter Name="State_Home" Type="String" /> <asp:Parameter Name="Prov_Home" Type="String" /> <asp:Parameter Name="ZipCode_Home" Type="String" /> <asp:Parameter Name="Country_Home" Type="String" /> <asp:Parameter Name="Phone_home" Type="String" /> <asp:Parameter Name="Phone_Home_Ext" Type="String" /> <asp:Parameter Name="Cell_home" Type="String" /> <asp:Parameter Name="Fax_home" Type="String" /> <asp:Parameter Name="Email_Home" Type="String" /> <asp:Parameter Name="material_status" Type="String" /> <asp:Parameter Name="DateOfBrith" Type="String" /> <asp:Parameter Name="company" Type="String" /> <asp:Parameter Name="Work_Field" Type="String" /> <asp:Parameter Name="Occupation" Type="String" /> <asp:Parameter Name="sub_Occupation" Type="String" /> <asp:Parameter Name="Other" Type="String" /> <asp:Parameter Name="Address1_work" Type="String" /> <asp:Parameter Name="Address2_work" Type="String" /> <asp:Parameter Name="City_Work" Type="String" /> <asp:Parameter Name="State_Work" Type="String" /> <asp:Parameter Name="Prov_Work" Type="String" /> <asp:Parameter Name="ZipCode_Work" Type="String" /> <asp:Parameter Name="Country_Work" Type="String" /> <asp:Parameter Name="Phone_Work" Type="String" /> <asp:Parameter Name="Phone_Work_Ext" Type="String" /> <asp:Parameter Name="Cell_Work" Type="String" /> <asp:Parameter Name="Fax_Work" Type="String" /> <asp:Parameter Name="Email_work" Type="String" /> <asp:Parameter Name="WebSite" Type="String" /> <asp:Parameter Name="Note" Type="String" /> <asp:Parameter Name="Groups" Type="String" /> <asp:Parameter Name="InterPhoneHome" Type="Int32" /> <asp:Parameter Name="InterMobileHome" Type="Int32" /> <asp:Parameter Name="InterFaxHome" Type="Int32" /> <asp:Parameter Name="InterPhoneWork" Type="Int32" /> <asp:Parameter Name="InterMobileWork" Type="Int32" /> <asp:Parameter Name="InterFaxWork" Type="Int32" /> <asp:Parameter Name="rdoPhoneHome" Type="Int32" /> <asp:Parameter Name="rdoMobileHome" Type="Int32" /> <asp:Parameter Name="rdoEmailHome" Type="Int32" /> <asp:Parameter Name="rdoPhoneWork" Type="Int32" /> <asp:Parameter Name="rdoMobileWork" Type="Int32" /> <asp:Parameter Name="rdoEmailWork" Type="Int32" /> <asp:Parameter Name="locationHome" Type="Int32" /> <asp:Parameter Name="locationWork" Type="Int32" /> <asp:Parameter Name="Original_idcontact_info" Type="Int32" /> </UpdateParameters> <InsertParameters> <asp:Parameter Name="Title" Type="String" /> <asp:Parameter Name="First_Name" Type="String" /> <asp:Parameter Name="Midle_Name" Type="String" /> <asp:Parameter Name="Last_Name" Type="String" /> <asp:Parameter Name="Address1_Home" Type="String" /> <asp:Parameter Name="Address2_Home" Type="String" /> <asp:Parameter Name="City_Home" Type="String" /> <asp:Parameter Name="State_Home" Type="String" /> <asp:Parameter Name="Prov_Home" Type="String" /> <asp:Parameter Name="ZipCode_Home" Type="String" /> <asp:Parameter Name="Country_Home" Type="String" /> <asp:Parameter Name="Phone_home" Type="String" /> <asp:Parameter Name="Phone_Home_Ext" Type="String" /> <asp:Parameter Name="Cell_home" Type="String" /> <asp:Parameter Name="Fax_home" Type="String" /> <asp:Parameter Name="Email_Home" Type="String" /> <asp:Parameter Name="material_status" Type="String" /> <asp:Parameter Name="DateOfBrith" Type="String" /> <asp:Parameter Name="company" Type="String" /> <asp:Parameter Name="Work_Field" Type="String" /> <asp:Parameter Name="Occupation" Type="String" /> <asp:Parameter Name="sub_Occupation" Type="String" /> <asp:Parameter Name="Other" Type="String" /> <asp:Parameter Name="Address1_work" Type="String" /> <asp:Parameter Name="Address2_work" Type="String" /> <asp:Parameter Name="City_Work" Type="String" /> <asp:Parameter Name="State_Work" Type="String" /> <asp:Parameter Name="Prov_Work" Type="String" /> <asp:Parameter Name="ZipCode_Work" Type="String" /> <asp:Parameter Name="Country_Work" Type="String" /> <asp:Parameter Name="Phone_Work" Type="String" /> <asp:Parameter Name="Phone_Work_Ext" Type="String" /> <asp:Parameter Name="Cell_Work" Type="String" /> <asp:Parameter Name="Fax_Work" Type="String" /> <asp:Parameter Name="Email_work" Type="String" /> <asp:Parameter Name="WebSite" Type="String" /> <asp:Parameter Name="Note" Type="String" /> <asp:Parameter Name="Groups" Type="String" /> <asp:Parameter Name="InterPhoneHome" Type="Int32" /> <asp:Parameter Name="InterMobileHome" Type="Int32" /> <asp:Parameter Name="InterFaxHome" Type="Int32" /> <asp:Parameter Name="InterPhoneWork" Type="Int32" /> <asp:Parameter Name="InterMobileWork" Type="Int32" /> <asp:Parameter Name="InterFaxWork" Type="Int32" /> <asp:Parameter Name="rdoPhoneHome" Type="Int32" /> <asp:Parameter Name="rdoMobileHome" Type="Int32" /> <asp:Parameter Name="rdoEmailHome" Type="Int32" /> <asp:Parameter Name="rdoPhoneWork" Type="Int32" /> <asp:Parameter Name="rdoMobileWork" Type="Int32" /> <asp:Parameter Name="rdoEmailWork" Type="Int32" /> <asp:Parameter Name="locationHome" Type="Int32" /> <asp:Parameter Name="locationWork" Type="Int32" /> </InsertParameters> </asp:ObjectDataSource> <asp:TextBox ID="txtSearch" runat="server" style="position:absolute; top: 560px; left: 170px;" ></asp:TextBox> <asp:Button ID="btnSearch" runat="server" Text="Search" style="position:absolute; top: 555px; left: 375px;" CausesValidation="False" onclick="btnSearch_Click"/> <asp:Label ID="Label7" runat="server" Style="position: absolute; top: 630px; left: 85px;" Text="First Name"></asp:Label> <asp:TextBox ID="txtFirstName" runat="server" Style="top: 630px; left: 185px; position: absolute; height: 22px; width: 128px"></asp:TextBox> <asp:Button ID="submit" runat="server" Text="submit" /> </div> </asp:Content>

    Read the article

< Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >