Search Results

Search found 29284 results on 1172 pages for 'weblogic 10 x'.

Page 440/1172 | < Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >

  • How can I get Haproxy to not log local requests?

    - by coneybeare
    I am trying to clean out some of the log clutter from my machines and am starting by removing requests that are generated from the server themselves. I have cache warmers running around the clock and I don't want these polluting the logs. I was able to get apache to stop logging local requests by adding a dontlog for the local IP: SetEnvIf Remote_Addr "RE\.DA\.CT\.ED" dontlog CustomLog "|logger -p local3.info -t http" combined env=!dontlog and now I am looking for something similar to put in a configuration for the Haproxy log. How can I prevent 127.0.0.1 requests from writing to the Haproxy log? UPDATE: 2/15/11 I use the excellent loggly service to pull out logs in the cloud, but I am seeing tons of logs like this: 2011 Feb 15 06:09:42.000 ip-10-251-194-96 http: RE.DA.CT.ED - - [15/Feb/2011:06:09:42 -0500] "HEAD /search/Nevad/predictive/txt HTTP/1.0" 200 - "-" "Wget/1.10.2 (Red Hat modified)" 2011 Feb 15 06:09:42.000 127.0.0.1 haproxy[10390]: 127.0.0.1:58408 [15/Feb/2011:06:09:42] www i-5dd7a331.0 0/0/0/8/8 200 210 - - --NI 0/0/0 0/0 "HEAD /search/Nevad/predictive/txt HTTP/1.1" and I want them gone. This question focuses on how to remove that haproxy log line from writing to the server side log in the first place.

    Read the article

  • Cisco BVI: Claiming IP addresses

    - by cjavapro
    I would like to make sure I understand this correctly. Given a Cisco ISO router that is set up with a BVI (a variation of a bridge route).. and the following layout "ISP router" \ "Network switch" # nothing special here. | \ | \ | \ | \ "Router 1 with NAT" "Router 2 with BVI" If I understand correctly.. the outside of a BVI will only respond to IP addresses that have already been claimed on the inside of the BVI... example subnet is 123.123.123.??? and servers inside the BVI on 123.123.123.10 and 123.123.123.11, and the NAT router is holding a public IP address of 123.123.123.50. If a connection comes in to 123.123.123.10 it will be received by router 2 but if it is received on 123.123.123.50, it will be received by router 1 and not received by router 2. and if a connection comes in to 123.123.123.90 (does not exist) it will not be received by either router. Am I correct? Is it true that the BVI router will not even receive packets to IP addresses that it does not see as existing on the inside?

    Read the article

  • Keep permalinks in Wordpress

    - by Remus Rigo
    Is there any way to set my permalinks to keep their exact link. If I have a post like this one http://blog.rigo.ro/?p=11, then I would like that every time I edit the post to keep this link. I have installed the Revision Control plugin and I set it to do not keep revisions. Any ideea how to do this? I want to keep this format of links. Edit: I took a look again, the permalinks keep their links, but every time I edit it adds a new version to the database and the next post will have a higher number. If I edit my current post for 3 times (blog.rigo.ro/?p=11) the next post will be blog.rigo.ro/?p=14. Now, my question is how can I keep all my post and edits clean, one post/more edits = one entry in the database, so if I have. 10 post on my site and I edit them, I would like that my permalinks to be from 1 to 10. PS: I don't want to edit my database manually, is there any plugin to do this?

    Read the article

  • Is there any way for ME to improve routing to an overseas server? [migrated]

    - by Simon Hartcher
    I am trying to make a connection to a gaming server in Asia from Australia, but my ISP routes my connection through the US. Tracing route to worldoftanks-sea.com [116.51.25.54]over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.1.1 2 34 ms 42 ms 45 ms 10.20.21.123 3 40 ms 40 ms 43 ms 202.7.173.145 4 51 ms 42 ms 36 ms syd-sot-ken-crt1-ge-6-0-0.tpgi.com.au [202.7.171.121] 5 175 ms 200 ms 195 ms ge5-0-5d0.cir1.seattle7-wa.us.xo.net [216.156.100.37] 6 212 ms 228 ms 229 ms vb2002.rar3.sanjose-ca.us.xo.net [207.88.13.150] 7 205 ms 204 ms 206 ms 207.88.14.226.ptr.us.xo.net [207.88.14.226] 8 207 ms 215 ms 220 ms xe-0.equinix.snjsca04.us.bb.gin.ntt.net [206.223.116.12] 9 198 ms 201 ms 199 ms ae-7.r20.snjsca04.us.bb.gin.ntt.net [129.250.5.52] 10 396 ms 391 ms 395 ms as-6.r20.sngpsi02.sg.bb.gin.ntt.net [129.250.3.89] 11 383 ms 384 ms 383 ms ae-3.r02.sngpsi02.sg.bb.gin.ntt.net [129.250.4.178] 12 364 ms 381 ms 359 ms wotsg1-slave-54.worldoftanks.sg [116.51.25.54] Trace complete. Since I think it will be unlikely that my ISP will do anything, are there any ways to improve my routing to the server without them having to intervene? NB. The game runs predominately over UDP, so I believe most low ping services are out of the question, as they rely on TCP traffic.

    Read the article

  • mysql_query missing during installation

    - by Arsenal
    Hi, I'm trying to install the pdo_mysql extension... I managed to install it succesfully, but ever since I upgraded mysql to 5.1.34 (using rpm packages) it seems to have gone down so I tried to reinstall it. However it seems to crash on ./configure as it gives 'mysql_query not found' error: configure:3961: checking for mysql_query in -lmysqlclient configure:3991: gcc -o conftest -g -O2 -I/usr/local/include/php -Wl,- rpath,/usr/lib/mysql -L/usr/lib/mysql -lmysqlclient -lz -lcrypt -lnsl -lm -lmygcc conftest.c -lmysqlclient -rdynamic -L/usr/lib/mysql -lmysqlclient -lz -lcrypt -lnsl -lm - lmygcc >&5 /usr/bin/ld: skipping incompatible /usr/lib/mysql/libmysqlclient.a when searching for -lmysqlclient /usr/bin/ld: skipping incompatible /usr/lib/mysql/libmysqlclient.a when searching for -lmysqlclient /usr/bin/ld: skipping incompatible /usr/lib/gcc/x86_64-redhat-linux/3.4.6/../../../libmysqlclient.so when searching for -lmysqlclient /usr/bin/ld: skipping incompatible /usr/lib/libmysqlclient.so when searching for -lmysqlclient /usr/bin/ld: cannot find -lmysqlclient collect2: ld returned 1 exit status configure:3997: $? = 1 configure: failed program was: | /* confdefs.h. */ ... In that file there seems to be a mysql_query(); statement. I'm pretty sure mysql_query works however since all of my websites are running normally. However the current setup is a mess (previous students kind of messed it up) and there are a whole lot of libmysqclient's in /etc: libmysqlclient.so.10.0.0 libmysqlclient.so.12.0.0 libmysqlclient.so.14.0.0 libmysqlclient.so.15.0.0 libmysqlclient.so.16.0.0 libmysqlclient_r.so.10.0.0 libmysqlclient_r.so.12.0.0 libmysqlclient_r.so.14.0.0 libmysqlclient_r.so.15.0.0 libmysqlclient_r.so.16.0.0 And just as much symlinks. Does anyone know how to get this right? Many thanks! (oh, and no pecl install pdo_mysql doesn't get me any further). I'm runnnig CentOS 4 with php 5.2.9 compiled from source and MySQL 5.1.34

    Read the article

  • Linux server: Dropped packets

    - by Lars
    I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

    Read the article

  • git : The remote end hung up unexpectedly - too many simultaneous users?

    - by Pritam Barhate
    I asked this first on StackOverflow and I was suggested that I should ask it here: We have a self hosted git server (Gitolite) on a VPS account (CPU:2.68GHz RAM:1824MB). This same VPS is also used to publish our underdevelopment web apps for client demos. (Very little traffic). so the main use of the server is as a Git Server Only. This git server is accessed by a team of 30-40 people for various projects. Our problem is that during the day when 6-7 people are trying to access the server (sometimes same repo) we get frequent error message: ssh: connect to host xxx.xxx.xx.xx port 22: Bad file number fatal: The remote end hung up unexpectedly After trying for 10-15 minutes it generally succeeds. During early mornings and late nights when there are only 1-2 people, git commands work with 100% success rate. Also I would like to note that if I access the other file hosted on the server through HTTP it works fine. I found a couple of questions on StackOverflow and on other sites regarding this. But most of the people point towards SSH key set up or conflicts between Msysgit and Cygns SSH. However I don't think this is the problem in our case as we get this behavior on Windows (using msysgit only) as well as Mac Machines. Also if it was SSH configuration issue then it shouldn't work at all. But in our case it works after 10-15 minutes. I think in our case it might be too many simultaneous connections to same server (or same repo) or something like that. Does there exists a setting or a conf file that needs to modified to solve this problem? Please help me solve this problem or point me in the right direction. Thanks in advance. Pritam.

    Read the article

  • Should I expect ICMP transit traffic to show up when using debug ip packet with a mask on a Cisco IOS router?

    - by David Bullock
    So I am trying to trace an ICMP conversation between 192.168.100.230/32 an EZVPN interface (Virtual-Access 3) and 192.168.100.20 on BVI4. # sh ip access-lists 199 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 # sh debug Generic IP: IP packet debugging is on for access list 199 # sh ip route | incl 192.168.100 192.168.100.0/24 is variably subnetted, 2 subnets, 2 masks C 192.168.100.0/24 is directly connected, BVI4 S 192.168.100.230/32 [1/0] via x.x.x.x, Virtual-Access3 # sh log | inc Buff Buffer logging: level debugging, 2145 messages logged, xml disabled, Log Buffer (16384 bytes): OK, so from my EZVPN client with IP address 192.168.100.230, I ping 192.168.100.20. I know the packet reaches the router across the VPN tunnel, because: policy exists on zp vpn-to-in Zone-pair: vpn-to-in Service-policy inspect : acl-based-policy Class-map: desired-traffic (match-all) Match: access-group name my-acl Inspect Number of Half-open Sessions = 1 Half-open Sessions Session 84DB9D60 (192.168.100.230:8)=>(192.168.100.20:0) icmp SIS_OPENING Created 00:00:05, Last heard 00:00:00 ECHO request Bytes sent (initiator:responder) [64:0] Class-map: class-default (match-any) Match: any Drop 176 packets, 12961 bytes But I get no debug log, and the debugging ACL hasn't matched: # sh log | inc IP: # # sh ip access-lists 198 Extended IP access list 198 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 Am I going crazy, or should I not expect to see this debug log? Thanks!

    Read the article

  • Configuring wsgi for a simple Python based site

    - by jbbarnes
    I have an Ubuntu 10.04 server that already has apache and wsgi working. I also have a python script that works just fine using the make_server command: if __name__ == '__main__': from wsgiref.simple_server import make_server srv = make_server('', 8080, display_status) srv.serve_forever() Now I would like to have the page always active without having to run the script manually. I looked at what Moin is doing. I found these lines in apache2.conf: WSGIScriptAlias /wiki /usr/local/share/moin/moin.wsgi WSGIDaemonProcess moin user=www-data group=www-data processes=5 threads=10 maximum-requests=1000 umask=0007 WSGIProcessGroup moin And moin.wsgi is as listed: import sys, os sys.path.insert(0, '/usr/local/share/moin') from MoinMoin.web.serving import make_application application = make_application(shared=True) QUESTION: Can I create a similar section in apache2.conf pointing to another wsgi file? Like this: WSGIScriptAlias /status /mypath/status.wsgi WSGIDaemonProcess status user=www-data group=www-data processes=5 threads=10 maximum-requests=1000 umask=0007 WSGIProcessGroup status And if so, what is required to convert my simple_server script into a daemonized process? Most of the information I find about wsgi is related to using it with frameworks like Django. I haven't found a simple howto detailing how to make this work. Thanks.

    Read the article

  • 500 Internal Server Error when setting up Apache on localhost

    - by Martin Hoe
    I downloaded and installed XAMPP, and to keep my projects nicely separated I want to create a VirtualHost for each one based on its future domain name. For example, in my first project (we'll say it's project.com) I've put this in my Apache configuration: NameVirtualHost 127.0.0.1 <VirtualHost 127.0.0.1:80> DocumentRoot C:/xampp/htdocs/ ServerName localhost ServerAdmin admin@localhost </VirtualHost> <VirtualHost 127.0.0.1:80> DocumentRoot C:/xampp/htdocs/sub/ ServerName sub.project.com ServerAdmin [email protected] </VirtualHost> <VirtualHost 127.0.0.1:80> DocumentRoot C:/xampp/htdocs/project/ ServerName project.com ServerAdmin [email protected] </VirtualHost> And this in my hosts file: # development 127.0.0.1 localhost 127.0.0.1 project.org 127.0.0.1 sub.project.org When I go to project.com in my browser, the project loads up successfully. Same if I go to sub.project.com. But, if I navigate to: http://project.com/register (one of my site pages) I get this error: Internal Server Error The server encountered an internal error or misconfiguration and was unable to complete your request. The error log shows this: [Sun May 20 02:05:54 2012] [error] [client 127.0.0.1] Request exceeded the limit of 10 internal redirects due to probable configuration error. Use 'LimitInternalRecursion' to increase the limit if necessary. Use 'LogLevel debug' to get a backtrace., referer: http://project.com/ Sun May 20 02:05:54 2012] [error] [client 127.0.0.1] Request exceeded the limit of 10 internal redirects due to probable configuration error. Use 'LimitInternalRecursion' to increase the limit if necessary. Use 'LogLevel debug' to get a backtrace., referer: http://project.com/ Any idea what config items I got wrong or how to get this working? It happens on any page that's not in in the root directory of project.com. Thanks.

    Read the article

  • Courier-imap login problem after upgrading / enabling verbose logging

    - by halka
    I've updated my mail server last night, from Debian etch to lenny. So far I've encountered a problem with my postfix installation, mainly that I managed to broke the IMAP access somehow. When trying to connect to the IMAP server with Thunderbird, all I get in mail.log is: Feb 12 11:57:16 mail imapd-ssl: Connection, ip=[::ffff:10.100.200.65] Feb 12 11:57:16 mail imapd-ssl: LOGIN: ip=[::ffff:10.100.200.65], command=AUTHENTICATE Feb 12 11:57:16 mail authdaemond: received auth request, service=imap, authtype=login Feb 12 11:57:16 mail authdaemond: authmysql: trying this module Feb 12 11:57:16 mail authdaemond: SQL query: SELECT username, password, "", '105', '105', '/var/virtual', maildir, "", name, "" FROM mailbox WHERE username = '[email protected]' AND (active=1) Feb 12 11:57:16 mail authdaemond: password matches successfully Feb 12 11:57:16 mail authdaemond: authmysql: sysusername=<null>, sysuserid=105, sysgroupid=105, homedir=/var/virtual, [email protected], fullname=<null>, maildir=xoxo.sk/[email protected]/, quota=<null>, options=<null> Feb 12 11:57:16 mail authdaemond: Authenticated: sysusername=<null>, sysuserid=105, sysgroupid=105, homedir=/var/virtual, [email protected], fullname=<null>, maildir=xoxo.sk/[email protected]/, quota=<null>, options=<null> ...and then Thunderbird proceeds to complain that it cant' login / lost connection. Thunderbird is definitely not configured to connect through SSL/TLS. POP3 (also provided by Courier) is working fine. I've been mainly looking for a way to make the courier-imap logging more verbose, like can be seen for example here. Edit: Sorry about the mess, I've found that I've been funneling the log through grep imap, which naturally didn't display entries for authdaemond. The verbose logging configuration entry is found in /etc/courier/imapd under DEBUG_LOGIN=1 (set to 1 to enable verbose logging, set to 2 to enable dumping plaintext passwords to logfile. Careful.)

    Read the article

  • Apache Mod SVN Access Forbidden

    - by Cerin
    How do you resolve the error svn: access to '/repos/!svn/vcc/default' forbidden? I recently upgraded a Fedora 13 server to 16, and now I'm trying to debug an access error with a Subversion server running on using Apache with mod_dav_svn. Running: svn ls http://myserver/repos/myproject/trunk Lists the correct files. But when I go to commit, I get the error: svn: access to '/repos/!svn/vcc/default' forbidden My Apache virtualhost for svn is: <VirtualHost *:80> ServerName svn.mydomain.com ServerAlias svn DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/var/www/html"> Options Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <Location /repos> Order allow,deny Allow from all DAV svn SVNPath /var/svn/repos SVNAutoversioning On # Authenticate with Kerberos AuthType Kerberos AuthName "Subversion Repository" KrbAuthRealms mydomain.com Krb5KeyTab /etc/httpd/conf/krb5.HTTP.keytab # Get people from LDAP AuthLDAPUrl ldap://ldap.mydomain.com/ou=people,dc=mydomain,dc=corp?uid # For any operations other than these, require an authenticated user. <LimitExcept GET PROPFIND OPTIONS REPORT> Require valid-user </LimitExcept> </Location> </VirtualHost> What's causing this error? EDIT: In my /var/log/httpd/error_log I'm seeing a lot of these: [Fri Jun 22 13:22:51 2012] [error] [client 10.157.10.144] ModSecurity: Warning. Operator LT matched 20 at TX:inbound_anomaly_score. [file "/etc/httpd/modsecurity.d/base_rules/modsecurity_crs_60_correlation.conf"] [line "31"] [msg "Inbound Anomaly Score (Total Inbound Score: 15, SQLi=, XSS=): Method is not allowed by policy"] [hostname "svn.mydomain.com"] [uri "/repos/!svn/act/0510a2b7-9bbe-4f8c-b928-406f6ac38ff2"] [unique_id "T@Sp638DCAEBBCyGfioAAABK"] I'm not entirely sure how to read this, but I'm interpreting "Method is not allowed by policy" as meaning that there's some security Apache module that might be blocking access. How do I change this?

    Read the article

  • Network connection keeps dropping - bad hardware?

    - by Bill Sambrone
    Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

    Read the article

  • Slackware - Assigning routes (IP address ranges) to one of many network adapters

    - by Dogbert
    I am using a Slackware 13.37 virtual machine within VirtualBox (current). I currently have a number of Ubuntu VMs on a single server, along with this Slackware VM. All VMs have been set up to use "Internal Network" mode, so they are all on a private LAN, and can see each other (ie: share files amongst themselves), but they remain private from the outside world. On on the these VMs (the Slackware one), I need to be able to grant it access to both this private network, and the internet at large. The first suggestion I found for handling this is to add another virtual network adapter to the VM, then set it to NAT. This results in the Slackware VM having the following network adapter setup: -NIC#1: Internal Network -NIC#2: NAT I want to set up the first network adapter (NIC#1) to handle all traffic on the following subnets: 10.10.0.0/255.255.0.0 192.168.1.0/255.255.255.0 And I want the second virtual network adapter (NIC#2) to handle everything else (ie: internet access). May I please have some assistance in setting this up on my Slackware VM? Additionally, I have searched for similar questions on SuperUser and Stackoverflow, but they all seem to pertain to my situation (ie: they all refer to OSX, or Ubuntu via the use of some UI-based tool). I'm trying to do this on Slack specifically via the command-line. Thanks!

    Read the article

  • convert a pdf/djvu file to png's under Linux how? [closed]

    - by user66732
    Imagemagick doesn't work (Fedora 14) on one PDF file: $ convert -density 300 INPUT.PDF out.png Error: /ioerror in --showpage-- Operand stack: 1 true Execution stack: %interp_exit .runexec2 --nostringval-- --nostringval-- --nostringval-- 2 %stopped_push --nostringval-- --nostringval-- --nostringval-- false 1 %stopped_push 1878 1 3 %oparray_pop 1877 1 3 %oparray_pop 1861 1 3 %oparray_pop --nostringval-- --nostringval-- 141 1 319 --nostringval-- %for_pos_int_continue --nostringval-- --nostringval-- 1761 0 9 %oparray_pop --nostringval-- --nostringval-- Dictionary stack: --dict:1157/1684(ro)(G)-- --dict:1/20(G)-- --dict:75/200(L)-- --dict:75/200(L)-- --dict:108/127(ro)(G)-- --dict:288/300(ro)(G)-- --dict:22/25(L)-- --dict:6/8(L)-- --dict:22/40(L)-- Current allocation mode is local Last OS error: 27 GPL Ghostscript 8.71: Unrecoverable error, exit code 1 convert: Postscript delegate failed INPUT.PDF': @ error/pdf.c/ReadPDFImage/645.<br> convert: missing an image filenameout.png' @ error/convert.c/ConvertImageCommand/2953. $ And it doesn't work on a djvu file: $ convert -density 300 INPUT.DJVU out.png convert: no decode delegate for this image format INPUT.DJVU' @ error/constitute.c/ReadImage/532.<br> convert: missing an image filenameout.png' @ error/convert.c/ConvertImageCommand/2953. $ an extra: the output filenames. out-0.png out-1.png ... out-9.png out-10.png out-11.png .. out-123.png out-124.png is there a way to be like this?: out-000.png out-001.png ... out-009.png out-010.png out-011.png .. out-123.png out-124.png because they would be in wrong order: out-0.png out-1.png out-10.png out-11.png out-123.png out-124.png out-9.png thank you :\

    Read the article

  • Set up multiple websites on a local web server

    - by mickburkejnr
    I have spent the last few days setting up a CentOS 6 server on my local network so that I can host multiple projects that I'm currently working on. Everything has been set up so that I access the server by typing 192.168.1.10 and the Apache test page comes up. What I'm aiming to do is to access different projects by typing in 192.168.1.10/project, and then view the project as if it was on it's own standalone server. I have thought about just sticking these sites inside folders on the server then accessing them that way, but a lot of my projects use CakePHP so this isn't feasible. So what I need to do is create VirtualHosts in Apache to allow me to do this, but without using a domain name. I want to stick to using the IP address of the machine (which is static). Any ideas? EDIT I've followed Peter's suggestion, but now I have a new problem. In the httpd.conf file I have entered the following information: NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /www/html/project1 ServerName local.project1.com ErrorLog logs/local.project1.com-error_log CustomLog logs/local.project1.com-access_log common </VirtualHost> And now Apache is saying: Starting httpd: Warning: DocumentRoot [/www/html/project1] does not exist When it clearly does exist. I've disabled SELinux and I can confirm this isn't turned on. I've also checked the ownership of the folder, and its owned by root. I can also save files to these folders using a guest FTP account (which isn't associated to root), so the folders are being listed and can be written to. But when I try the folder in a web browser it doesn't seem to work either. I've also done a reboot of the server and the problem persists. What should I change in order to resolve this?

    Read the article

  • Adding 2nd DC to the domain from a different subnet over VPN.

    - by EagerToLearn
    I'm in the process of adding a second DC to our domain and just want to make sure I have all the steps right before proceeding. Info: DC1 is 2008 R2 Standard. DC2 is 2008 R2 Standard. Network1 is 192.168.39.x/24 Network2 is 10.0.0.x/24 VPN is Sonicwall. The 2 DC's will be at two different sites, but the networks are connected by hardware VPN. (Sonicwall). The main DC server will be on the 192.168.39.0/24 network. The 2nd DC will be on 10.0.0.0/24. Here are the steps I plan to take; please let me know if I'm missing anything. Part 1: AD Sites and Services on DC1, create a new site and subnet for DC2. (Or should I create a new one for both?) (Can I use the default IPSiteLink and not change anything in there other than refresh timer?) Part 2: Point the DNS of DC2 to DC1. Run /forestprep and /domainprep (on both, or just DC1?). Dcpromo and select "Additional Domain Controller for Existing Domain". Then continue with normal steps with default locations for databases. EDIT: Didn't realize this was like reddit and required two skipped lines to skip one :P EDIT 2: When DCPromo-ing DC2, do I need to have "Append primary and connection specific DNS" and "Append parent suffixes of the primary DNS suffix" checked?

    Read the article

  • Why is writing to my external hard drive slow, while benchmarks show fast writing?

    - by matix2267
    I have an iOmega eGo 320GB portable drive connected through USB2.0 to my laptop running Windows Vista. It's been working fine for quite some time until recently it became very slow when writing e.g. when copying ~300MB movie over to the drive at first it is extremely fast but it actually doesn't write it only puts in cache and then hangs on last 10-20MBs for about a minute. When copying larger files it's the same story: starts fast but then slows down to ~5MB/s (sometimes even slower down to 2MB/s). Strange thing is that I have always had caching disabled for this drive (it was disabled by default and I never bothered changing it). At first I thought that the disk is dying so I checked S.M.A.R.T. values and everything is fine there. I also run chkdsk and it seemed to fix the problem - it worked fast for a few minutes but then it slowed down again. I also tried plugging it into another USB port - no difference. Additionally I noticed that reading under certain circumstances is sometimes slower e.g. loading times for some games are ~10 times longer, whereas simple copying files from this drive to my internal HDD is fast. I ran a speed benchmark using CrystalDiskMark with a 5x100MB run and strangely got these results: read write (MB/s) Seq 33.05 28.25 512k 17.30 15.27 4k 0.267 0.372 4kQD32 0.510 0.260 This is different from what most other people have (I've found many threads about slow disk write while googling but all of them were slow on benchmarks too) which is why I decided to post this problem here. BTW most of the time when writing (or sometimes reading) the activity led is mostly idle (blinks a while and then stops for longer, sometimes has slower blinks ~1 sek, sometimes goes off for a few seconds - extremely long blink :) ) but when benchmarking, defragmenting or just reading (copying from this drive, installing apps from installers there, watching HD videos) it is blinking really fast (like it should) and there are no slowdowns. It shouldn't be driver issue unless stock Windows drivers have some issues I'm not aware of.

    Read the article

  • Terratec Cinergy Hybrid T USB XS is not recognized anymore on Mac OS X

    - by Gabble
    I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. It is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. Reset the PRAM. Nope. Checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. I need to say that: a) The device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause). b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me. Thanks in advance for any help you will offer!

    Read the article

  • WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

    - by Elton Carvalho
    I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

    Read the article

  • Using udev to create a character device based on a driver being loaded

    - by SteveCB
    I'm in the process of setting up RAID monitoring for a number of Dell servers that use the PERC 6i integrated card. We're using Nagios at present and the check_megasasctl plugin seems to fit the bill. However, the plugin relies upon the existence of: /dev/megaraid_sas_ioctl_node This device node doesn't exist by default, you have to create it by hand using something like: mknod /dev/megaraid_sas_ioctl_node c 253 0 Now, to make the existence of this device node persistent across reboots, I thought I could write a udev rule, but as usual, I'm missing something. I thought I could create a file such as /etc/udev/rules.d/10-local/rules that contained: DRIVER=="megasas" NAME="megaraid_sas_ioctl_node" MODE="0600" But this doesn't work - no device node after a reboot. Dmesg output indicates the megasas driver is loaded and functional: megasas: 00.00.04.01-RH1 Thu July 10 09:41:51 PST 2008 megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0 megasas: FW now in Ready state Further, I don't see any means to instruct udev on which type of device node to create: character or block. I suspect I'm failing to understand exactly how udev is meant to work. I realise I could just cheat and run MegaCLI in /etc/rc.local, redirecting output to /dev/null; it creates the megaraid_sas_ioctl_node device node as part of its execution. I just thought using udev rules would be a) cleaner and b) a useful learning exercise. Perhaps I should just dump the above mknod command in /etc/rc.local... So how do I get udev to create the /dev/megaraid_sas_ioctl_node device node based on the presence of the megasas driver? Cheers Steve

    Read the article

  • Two DHCP interfaces asigned to two default gateways to OS

    - by user140600
    I have a Ubuntu box that has two networking interfaces (eth0 and wlan0). They are both configured for DHCP in /etc/network/interfaces, but they both assign a default gateway: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto wlan0 iface wlan0 inet dhcp wireless-essid test Result of route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.1.1 0.0.0.0 UG 100 0 0 wlan0 0.0.0.0 10.0.0.1 0.0.0.0 UG 100 0 0 eth0 10.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 172.16.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 How can I set up /etc/network/interfaces to have only one default gateway, on the interface I want? Worst case scenario, how can I at least control which one gets on top on the route -n command, each boot? Note: This box will travel a lot, and will be connected to different networks, so I don´t know in advance the IP addresses/ranges it will have. Sometimes the default gw interface will be eth0. Sometimes it will be wlan0 ... So, this needs to be kind of automatic ...

    Read the article

  • very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

    - by gojira
    I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

    Read the article

  • What is wrong with those crontabs?

    - by Guillaume Boudreau
    I want my projectors to Power On before the mall opens, and Power Off when the mall closes. So I created crontab entries (that I placed in /etc/cron.d/mall), but today (Thu Nov 22 18:58:29 EST 2012 is the current date on that server), the power-off.sh script got executed at 17:20 (see syslog excerpt below). Being Thu, Nov. 22, I would have expected the power-off.sh script to be executed at 21:20, per the 4th crontab line below. Why did power-off.sh execute at 17:20? What is wrong with my crontab entries? Content of /etc/cron.d/mall: 40 9 22-30 Nov Mon-Sat myuser /usr/local/projectors/power-on.sh 40 10 22-30 Nov Sun myuser /usr/local/projectors/power-on.sh 20 18 22-30 Nov Mon-Wed myuser /usr/local/projectors/power-off.sh 20 21 22-30 Nov Thu-Fri myuser /usr/local/projectors/power-off.sh 20 17 22-30 Nov Sat-Sun myuser /usr/local/projectors/power-off.sh 40 9 1-22 Dec Mon-Sat myuser /usr/local/projectors/power-on.sh 40 10 1-22 Dec Sun myuser /usr/local/projectors/power-on.sh 20 21 1-22 Dec Mon-Fri myuser /usr/local/projectors/power-off.sh 20 17 1-22 Dec Sat-Sun myuser /usr/local/projectors/power-off.sh syslog excerpt: $ grep power-off.sh /var/log/syslog Nov 22 17:20:01 lanner-ubu-c2d CRON[23007]: (myuser) CMD (/usr/local/projectors/power-off.sh)

    Read the article

  • Squid reverse proxy array - siblings not communicating with each other

    - by V. Romanov
    I want to set up 2 squid servers to act as reverse proxy and cache for a webserver on our intranet. The load balancing will be done with DNS round robin or just different mappings for different clients. The thing is, I want both servers to try and contact each other to see if they have the object required in cache before contacting the webserver for it (the network that servers the webserver is the bottleneck and I'm trying to eliminate it) Both squids are configured the same, here are the relevant config lines : acl dvr1_cache_it_best_tv_com dstdomain dvr1.cache.it.best-tv.com acl squid1_it_best_tv_com dstdomain squid1.it.best-tv.com acl squid2_it_best_tv_com dstdomain squid2.it.best-tv.com http_access allow dvr1_cache_it_best_tv_com http_access allow squid1_it_best_tv_com http_access allow squid2_it_best_tv_com http_access allow all http_port 8081 accel defaultsite=dvr1.cache.it.best-tv.com cache_peer dvr1.origin.it.best-tv.com parent 80 0 no-query originserver name=Proxy_dvr1_origin_it_best_tv_com cache_peer squid1.it.best-tv.com sibling 8081 3130 weight=10 name=Proxy_Squid1_it_best_tv_com cache_peer squid2.it.best-tv.com sibling 8081 3130 weight=10 name=Proxy_Squid2_it_best_tv_com cache_peer_access Proxy_dvr1_origin_it_best_tv_com allow dvr1_cache_it_best_tv_com cache_peer_access Proxy_squid1_it_best_tv_com allow squid1_it_best_tv_com cache_peer_access Proxy_squid1_it_best_tv_com allow squid2_it_best_tv_com cache_peer_access Proxy_squid1_it_best_tv_com allow dvr1_cache_it_best_tv_com cache_peer_access Proxy_squid2_it_best_tv_com allow squid1_it_best_tv_com cache_peer_access Proxy_squid2_it_best_tv_com allow squid2_it_best_tv_com cache_peer_access Proxy_squid2_it_best_tv_com allow dvr1_cache_it_best_tv_com just to make it clear - dvr1.cache is the alias for the proxy servers. dvr1.origin is the web server. Both servers work, both serve content and cache it and work fine. However, when I clear the cache on one server and then access it, it gets the content from the parent (DVR1_ORIGIN) instead of going to the sibling squid. What did I configure wrong? Or perhaps I don't understand the architecture correctly? I read the squid manuals but as far as I see i did it all by the book and yet it doesn't work right. Any help will be appreciated!

    Read the article

< Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >