Search Results

Search found 13930 results on 558 pages for 'dev center'.

Page 445/558 | < Previous Page | 441 442 443 444 445 446 447 448 449 450 451 452  | Next Page >

• No Homegroup Computers, Network Troubleshooter Fails

  - by Mokubai

  I have a problem with my Windows 7 Homegroup, between two Windows 7 Home Premium machines. On one machine I get this: The other machine in the Homegroup is perfectly happy and is able to see and browse this faulty machine as if there is nothing wrong. The Network and Sharing Center shows that I am joined to a Homegroup on my "Home" network and nothing is out of the ordinary. I have tried leaving the Homegroup and rejoining/recreating it several times and that does nothing at all. Normal browsing to machine names and looking through folders seems to work, but it's a much more clunky way to get stuff compared to the convenience of the Homegroup facilities. Starting the troubleshooter detects some problems with a "Peer Networking" (PNRpr or something like that) service not starting but fails to fix anything. Sure enough when I go to view the services via Control Panel - Administrative Tools - Services I see that both the "Peer Name Resolution Protocol" and "Peer Networking Grouping" services are stopped. Attempting to start the "Peer Networking Grouping" gives an error that a dependency service will not start, the only service it is dependant on is the "Peer Name Resolution Protocol" so I try to start that and I get an error saying that the "service could not start due to error 0x80630801" This has happened before and I have fixed it then by using System Restore and restoring the machine to a week before when I knew it had all worked. This time though I cannot remember when I last used the Homegroup from this machine and I've installed quite a bit so I don't want to go fumbling through restore points trying to find one that works... Can anyone tell me if there is a way to reset things so that this machine is able to use the Homegroup again?

  Read the article

• Monitor displays at 1024x768; scrolls screen for higher resolutions

  - by Matt

  I have a dual monitor setup. Normally, they both display at 1680x1050. They have been setup this way for about a year. I'm using Windows XP Professional 2003 x64 SP2. Today, out of nowhere, one of the monitors kicked back to a lower resolution. I was not playing with any configuration at the time.. in fact all I had done was close a window (maybe a browser). But the thing is that the resolution is still preserved partially by the fact that the screen will scroll when you move the mouse. So it's like looking through a 1024x768 window into a 1680x1050 world. The monitor itself does not appear to be damaged, because I also have it connected to my netbook (via KVM) and higher resolutions work fine. I tried uninstalling/reinstalling the drivers to no avail. System restore doesn't help either. I'm unsure of the exact ATI card I'm using.. Device Manager lists it as "Radeon X300/X550/X1050". There is no Catalyst Control Center software installed. I tried to install it, but there doesn't seem to be a way to install it by itself ... it forces you to install another driver, which breaks both of my displays, forcing me to go into safe mode and run system restore again. Any ideas? Thanks

  Read the article

• Recover data from physically damaged harddrive. What are my options?

  - by Michael Kniskern

  I was trying to replace the power supply in my desktop PC and ended up physically damaging the data connection from the hard drive to the motherboard. The plastic shelf for the copper prongs on the hard drive broke into the cable. Here is a picture of my handy work: I went to Best Buy Geek Squad to discuss my options and they said that they will need to send it to the recover center it could cost anywhere between $250 to $1600 USD to recover the data out the hard drive Is this reasonable for data recovery from a physically damaged hard drive? Are there any other options I can explore? I am going to talk to the data doctors to see what my options are. Update I took the HD to Data Doctors, and they told me that the SATA connection was broken to they would need to replaced the data connector and then copy the data to a brand new hard drive. So, with the initial analysis, cost of replacement parts, and data recovery fee it came out to $865.00 USD. The technician specifically stated if this was an older hard drive that would just need to replace the data connector. But because there is specific information related to the individual hard drive in the flash ROM, they need to transfer the data to a brand new hard drive.

  Read the article

• Disk Partitioning problem with fdisk.

  - by MA1

  Currently i am using fdisk to create/resize windows partitions. Following is a sample input script to fdisk to create/resize windows partitions: fdisk /dev/sda < partInput the contents of partInput are as follows: d #delete the partition 3 #partition number to be deleted n #add a new partition p #primary: type of new partition 3 #new partition number 18804 #start cylinder of new partition 77433 #end cylinder of new partition t #change the type of partition 3 #partition number whose type(filesystem) is to be changed 7 #HPFS/NTFS: partition type(filesystem) n #add a new partition p #primary: type of partition 77434 #first cylinder of new partition 77825 #end cylinder new partition w #write all the above changes As you see in the above input we are using cylinders for start and end. Earlier i am using sectors as unit and everything is working fine but getting problems when partitioning a 1.5TB hard drive. Then i changed the unit to cylinders but it is working on some machines not all. On some machines fdisk failed to create the partition table correctly. So, i am thinking to move to parted if there is no way to do the above using fdisk. Please also tell me how to correctly convert sectors to cylinders? How to perform all the above steps using parted without losing the data OR how to use fdisk correctly?

  Read the article

• Translating IPTables rule to UFW

  - by Dario Fumagalli

  we are using an Ubuntu 12.04 x64 LTS VPS. Firewall being used is UFW. I have setup a Varnish + LEMP setup. along with other things, including an Openswan IPSEC VPN from our office to the VPS data center. A second in house Ubuntu box is to act as MySQL slave and fetch data from the VPS through the VPN. Master's ppp0 is seen as 10.1.2.1 from the slave, they ping etc. I have done the various required tasks but I can't get the client (slave) MySQL (nor telnet 10.1.2.1 3306) to access the master through the VPN unless I issue this fairly obvious IPTables command: iptables -A INPUT -s 10.1.2.0/24 -p tcp --dport 3306 -j ACCEPT I willingly forced the accepted input to come from the last octet. With this rule everything works just fine! However I want to translate this command to UFW syntax so to keep everything in one place. Now I admit being inexperienced with UFW, I prepared rules like: ufw allow proto tcp from 10.1.2.0/24 port mysql and 2-3 variations involving specifying 3306 instead of mysql, specifying a target IP (MySQL's my.cnf at the moment is configured as 0.0.0.0) and similar but I just don't seem to be able to replicate the simple iptables rule in a functional way. Anyone could kindly give me a suggestion that is not to dump UFW? Thanks in advance.

  Read the article

• Finding custom printer-specific options on *nix

  - by enbuyukfener

  Hey all, I have a printer set up using CUPS (FujiXerox Document Center 1100), it is named DC1100. There are capabilities of the printer that are not shows as options of the printer as listed by: lpoptions -l -d DC1100 The output is below: PrintoutMode/Printout Mode: Draft *Normal High Photo InputSlot/Media Source: Upper Lower MultiPurpose LargeCapacity Manual *Standard PageSize/Page Size: *Letter A4 C5 C6 COM10 DL Executive Legal Monarch Statement PageRegion/PageRegion: Letter A4 C5 C6 COM10 DL Executive Legal Monarch Statement STP_Brightness/Brightness: 0.00 0.02 0.04 [snip] 2.00 STP_Contrast/Contrast: 0.00 0.05 0.10 0.15 [snip] 4.00 STP_ColorCorrection/Color Correction: Accurate Bright Density [snip] Uncorrected STP_DitherAlgorithm/Dither Algorithm: Adaptive EvenTone Fast [snip] VeryFast STP_EnableDensity/Density Enable: *Disabled Enabled STP_Density/Density Value: 0.1 0.2 0.3 0.4 [snip] 8.0 STP_EnableGamma/Composite Gamma Enable: *Disabled Enabled STP_Gamma/Composite Gamma Value: 0.10 0.15 0.20 0.25 [snip] 4.00 STP_LinearContrast/Linear Contrast Adjustment: *False True STP_Duplex/Double-Sided Printing: DuplexNoTumble DuplexTumble *None Resolution/Rendering Resolution: *FromPrintoutMode 150x150dpi 300x300dpi 600x600dpi OutputType/Output Type: *FromPrintoutMode BlackAndWhite Grayscale STP_ImageType/Image Type: *FromPrintoutMode Photo Graphics LineArt None Text TextGraphics STP_Resolution/Resolution: *FromPrintoutMode 150dpi 300dpi 600dpi I am particularly looking for options for: "secure print" (possibly by setting a mode and setting a username) stapling hole punching Perhaps I need a vendor specific driver/PPD file? If so, any pointers as I have no idea where to look for one. I haven't been able to find one on the official site or on sites such as http://www.openprinting.org

  Read the article

• Turn off gzip for a location in Nginx

  - by Nyxynyx

  How can gzip be turned off for a particular location and all its sub-directories? My main site is at http://mydomain.com and I want to turn gzip off for both http://mydomain.com/foo and http://mydomain.com/foo/bar. gzip is turned on in nginx.conf. I tried turning off gzip as shown below, but the Response Headers in Chrome's dev tools shows that Content-Encoding:gzip. How should gzip/output buffering be disabled properly? Attempt: server { listen 80; server_name www.mydomain.com mydomain.com; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; root /var/www/mydomain/public; index index.php index.html; location / { gzip on; try_files $uri $uri/ /index.php?$args ; } location ~ \.php$ { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; fastcgi_read_timeout 300; } location /foo/ { gzip off; try_files $uri $uri/ /index.php?$args ; } }

  Read the article

• File Replication Service Errors

  - by ekamtaj

  Hey Guys, We have a windows 2003 r2 server and couple of the users are reporting that they can not scan files into the windwos server. They are getting an Out of Space errors. I took a look at the server and we have 600GB free disk space on that partition. But while looking at the event log I found a lot of errors like (13552,13555) The File Replication Service is unable to add this computer to the following replica set: "DOMAIN SYSTEM VOLUME (SYSVOL SHARE)" This could be caused by a number of problems such as: -- an invalid root path, -- a missing directory, -- a missing disk volume, -- a file system on the volume that does not support NTFS 5.0 The information below may help to resolve the problem: Computer DNS name is "server.domain.local" Replica set member name is "server" Replica set root path is "c:\windows\sysvol\domain" Replica staging directory path is "c:\windows\sysvol\staging\domain" Replica working directory path is "c:\windows\ntfrs\jet" Windows error status code is FRS error status code is FrsErrorMismatchedJournalId Other event log messages may also help determine the problem. Correct the problem and the service will attempt to restart replication automatically at a later time. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Windows : Map-a-network-drive to a remote Shared-Folder (on QNAP NAS) using OpenVPN

  - by spelltox

  Provided my lack of networking knowledge, I've been struggling with this issue for quite a few days now : I have a QNAP-TS212 NAS on which i've created a shared-folder (mostly excel files). All the computers in the local network (windows) are able to access it without any problem. Now, i want to access that shared-folder remotely (windows client), so : I enabled OpenVPN (and PPTP) in QNAP admin. Installed OpenVPN on the remote client. Applied the configuration file that the QNAP generated - Configuration (openvpn.ovpn) : client dev tun script-security 3 proto udp remote ***MY_WAN_IP*** 1194 resolv-retry infinite nobind ca ca.crt auth-user-pass reneg-sec 0 cipher AES-128-CBC comp-lzo OpenVPN connect successfully from the remote client. Now, here's my problem : I can ping the NAS (got IP 10.8.0.1) from the remote client, But when i try to map-a-network-drive, i don't see the shared folder or the NAS or any of the other computers in the network... I checked - all computers are in "WORKGROUP" workgroup. I'm probably missing some basic knowledge, So - any help would be greatly appreciated ! Many thanks.

  Read the article

• Controlling clone access to multiple mercurial repos served via hgwebdir.cgi

  - by chrislawlor

  I'm trying to host multiple hg repositories to use for my clients. I need to control access to each repository individually - not just push access, but clone as well. I've got an .htaccess set which requires authentication globally: AuthUserFile /path/to/hgweb.passwd AuthGroupFile /dev/null AuthName "Chris Lawlor Client Mercurial Repositories" AuthType Basic <Limit GET POST PUT> Require valid-user </Limit> <FilesMatch "\.(htaccess|passwd|config|bak)$"> Order Allow,Deny Deny from all </FilesMatch> Then in each repository, I've got a .hg/hgrc file requiring a valid user [web] allow_push = <comma seperated user list> This almost does what I need. The problem is that I need to add ALL my clients to hgweb.passwd, which gives them clone access to ALL of the repositories. The only solution I can think of is to have another .htaccess and .passwd file in EACH repository. I don't really want to do that though, seems a little convoluted. I can already specify a list of authorized users for each repository in that repos' hgrc file with the allow_push setting. If only there were an allow_clone setting as well... All the documentation I've found for hgwebdir.cgi is incomplete. I've read: http://mercurial.selenic.com/wiki/HgWebDirStepByStep http://hgbook.red-bean.com/read/collaborating-with-other-people.html#sec:collab:cgi http://hgbook.red-bean.com/read/collaborating-with-other-people.html And others. I've yet to find a comprehensive list of hgrc settings. I guess this is as much an Apache question than a mercurial question. Unless I can find a better approach, I'll be going with a seperate .htaccess and .passwd file for each repo. This is a virtual host on Webfaction if it matters - set up roughly like this http://docs.webfaction.com/software/mercurial.html

  Read the article

• Cannot connect to windows server by name over vpn connection

  - by ErocM

  I have a rented dedicated windows server on a public ip that is acting as a SQL Server and VPN server. I need to connect to this server via computer name to get replication in place. I cannot use an ip address due to this issue: So, due to this, we are going the VPN route. That is my primary issue: After I am connected to this server's vpn, I can connect to SQL Server using the ip address but I cannot connect by the computer's name as you can see below... Right now, there is no hardware firewall on it since I had it removed to test this issue. I am running Windows 2008 Enterprise Server as the VPN server. I am not sure if the route print will help any from the workstation trying to connect but here is the info: IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.0.0.0 10.0.0.1 10.0.0.2 21 10.0.0.2 255.255.255.255 On-link 10.0.0.2 276 Any other info needed? Thanks for the help! ========= CLARIFICATION ON A FEW THINGS #1 ========= This is the server's info: This is the workstation that is trying to connect: I connect to the server via "Control Panel\Network and Internet\Network and Sharing Center\Connect or Disconnect" You can see here that I am connected: ========= CLARIFICATION ON A FEW THINGS #2 ========= I've tried to connect directly to the Sql Server as I did above but with the computers name and I couldn't get to it. Here I am trying to net view it from the workstation and it couldn't find it:

  Read the article

• Using my old PC as a web/file server?

  - by Garrett

  I have an old desktop computer that I've been trying to sell for AGES. I guess nobody is looking for computers because it was advertised at a dirt cheap price on craigslist, local papers, etc. Anyways, I was wondering if it would be worth it to set it up as a home file server, a web dev server (I have a web host for actual production use), and maybe host a few server applications (ex: ventrillo). The computer is actually an old Dell that I cannibalized after the motherboard being destroyed by lightning, so it has fairly new parts in it. The specs are: P4 3.4GHz w/ HT and Artic Cooling Freezer 7 3GB DDR2 533 RAM 80GB hdd (will upgrade the hard drive if it's even worth using as a server) basic dvd rom 430 Watt Thermaltake PSU (it might be important to note that it is only 60% efficiency) ATI Radeon x600 256MB Antec 300 case It's not a really beefy machine, I just can't see giving it away or putting it in the corner to just collect dust. I have Windows Server 2008 R2 Standard and I am confident in my skills in operating most Linux operating systems. I'd also be using it to tinker with when I learn new things in my server admin classes (I'm finishing my 2nd year in college at the moment so I'm still learning) Also, my house is quite old and the electrical wiring is pretty poor (it MIGHT be up to code, then again, where I live most people don't even know what regulations are or let alone know how to spell it...) Would it be safe to leave it running all day and is it going to run up my electric bill because of the PSU efficiency? I only have 5mbit cable internet, but I won't be running very bandwidth intense services on it so it should be ok. I should elaborate on why I am concerned about the power. The circuits should be fine, but I'm more concerned about fire hazard. What is the likelihood that the server could cause an electrical fire? Again, thank you all for the feedback!

  Read the article

• How do I create an MBR on a USB stick using DD command line tool

  - by Lana Miller

  Okay I'm trying to create a BOOTABLE Windows7 image on a USB key from a Mac running Lion. My image is .iso format. I tried: sudo dd if=/Users/myusername/Win7.iso of=/dev/disk1 bs=1m And this succeeded in writing the files, except in DISK UTILITY on the mac, it shows the partition type as GUID Partition Table and not 'Master Boor Record'. Booting the key on my Vista computer yields the error "No boot sector on USB Device' From what I can tell, bs=1m in the DD command should have left 1 Megabyte for the boot sector, but for some reason this area of the USB Key is not set up correctly so that it will boot How can I fix this, or correctly use dd to write a bootable cd image such that it is now a bootable usb drive? Note: in the instructions I read about, they recommended renaming my Win7.iso to Win7.dmg before using DD, which made absolutely no sense to me, so I didn't do it. I could try with that step now, but it takes 1.99 hours to write the image to the USB drive so there is a huge penalty to trial and error here. Thank you.

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7.

  Read the article

• Is there a way in Windows 7 to disable "journaling"?

  - by Psycogeek

  C:\$extend\$Usn.Jrnl:$J:$data Here is a picture finally. The large strip in the center of the top band is the largest chunk, in the other, grey areas are the various clusters with it. On the right, the big long grey line is $logfile (not paging), and it is 63&nbsb;MB. Paging, 500&nbsb;MB is the dark cyan chunk, next to the yellow MFTres in the inner rings.. The disk was defragged so they could be seen easier. Not all clusters of this type of file are tagged, but the idea is there. The disk is 4k clusters, now about 12 GB size. Each cute little block in the picture is .81 MB and represents 207 clusters. The dkGreen section, is mostly the whole Winsxs pile, also interesting when they keep telling us it doesn't take much disk space. Wikipedia suggests that in previous NT systems "USN journaling" would be turned on when enabled (assumes it could also be turned off?). What aspects, services, or program is working on putting that stuff all over the disk which is known by $jrnl$ type clusters, even if it is not actual USN journaling? Is it possible in a Windows 7 system to completly disable the journaling, and what would be the ramifications of that? On a Windows XP NTFS system, I do not recall seeing the quantity of disk clusters used with these $jrnl$ names, so I do not recall this being necessary in this quantity for an NTFS file system itself? I understand that it would not be there, if it did not have a useful function :-) Information about how wonderful is fine, if that information will help track down what parts of the system create and use it. Change Journals states: Change journals are also needed to recover file system indexing Hmm, that might explain some of them, or why it was left on the disk. A crash while background indexing?

  Read the article

• recursive grep started at / hangs

  - by Martin

  I have used following grep search pattern on multiple platforms: grep -r -I -D skip 'string_to_match' / For example on FreeBSD 8.0, FreeBSD 6.4 and Debian 6.0(squeeze). Command does a recursive search starting from root directory, assumes that binary files do not have the 'string_to_match' and skips devices, sockets and named pipes. FreeBSD 8.0 and FreeBSD 6.4 use GNU grep version 2.5.1 and Debian 6.0 uses GNU grep version 2.6.3. On FreeBSD 6.4, last information printed to stderr was "grep: /dev/cuad0: Device busy". After this grep just idles as according to "top -m io -o total" the I/O usage of grep is nonexistent. Same behavior is true under FreeBSD 8.0, but last information sent to stderr is "grep: /tmp/.wine-0: Permission denied" on my installation. In case of Debian, last output to stderr is "grep: /proc/sysrq-trigger: Input/output error". If I check the I/O usage of grep process under Debian, it is following: root@Debian:~# iotop -bp 22439 Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / ^Croot@Debian:~# What might cause this? Is there a way to view which file grep is currently processing in case lsof is not present? I'm able to use lsof under Debian and looks like the problematic file name there is "0xc6b2c230 file struct, ty=0, op=0xc0d34120". I'm not sure what this is.. I'm not able to use lsof or fstat under FreeBSD. PS: I know I could use find utility, but this is not the question.

  Read the article

• gcc built by crosstool-ng gives undefined reference

  - by netvope

  I've successfully built a toolchain using crosstool-ng with the default configuration named x86_64-unknown-linux-gnu. The documentation says: Using the toolchain is as simple as adding the toolchain's bin directory in your PATH, such as: export PATH="${PATH}:/your/toolchain/path/bin" and then using the target tuple to tell the build systems to use your toolchain: ./configure --target=your-target-tuple or make CC=your-target-tuple-gcc or make CROSS_COMPILE=your-target-tuple- and so on... I followed the instructions and attempted to build GNU tar (tar-1.25.tar.bz2) with the toolchain. The commands ./configure --target=x86_64-unknown-linux-gnu and make CROSS_COMPILE=x86_64-unknown-linux-gnu- do not work (the build will succeed, but it uses the host system's gcc). The command make CC=x86_64-unknown-linux-gnu-gcc works, but in the very last step when it tries to link, it returns errors like this: compare.o: In function `openat': /dev/shm/x-tools/x86_64-unknown-linux-gnu/x86_64-unknown-linux-gnu/sys-root/usr/include/bits/fcntl2.h:134: undefined reference to `__openat_2' What could be the problem? Was the toolchain not properly setup? Perhaps x86_64-unknown-linux-gnu-gcc is using the header files from the host system but could not find the libraries in the target's sys-root?

  Read the article

• Permissions nightmare - tried all I know

  - by Ben

  Working on a new client's dev site, which is a wordpress install on a Plesk box. I have SSH root access, and FTP access through a separate account. What I've done so far Initially I couldn't make any changes to any files at all. The permissions on all the template files looked a little screwy (644), so I figured change them to allow group, and add myself to the group: CHMOD Recursive on the theme folder to set everything to 664 Quickly realised I'd broken it, set the folders to 755, kept files as 664 Ownership on all files is a mixture of root:root and 500:500 (there is no user nor group with the ID of 500 on the server). Added myself to the group 'root' so I could modify the files too The Problem This worked OK, in terms of being able to edit the existing files, so I began working. However, I can't upload to the directory, even having run CHOWN -R root:root templatefolder/ and being in the root group. I feel like I must be missing something obvious, and it's doing my head in. Questions: Files in the install owned by 500 with group 500 - I've looked in /etc/group and /etc/passwd and there is no user nor group with this ID. Is that left over from another developer's setup or the previous server (they moved recently)? Is being in the 'root' group enough, or do I need to own the theme folder as 'myftpuser' in order to upload and create new files? Like I say, I have edit access, so I got myself this far. I'm now questioning what to do next!

  Read the article

• Window 7 Host does not answer to ping

  - by gencha

  Today I tried printing on a shared printer on one of our homegroup members. Sadly it did not work (printer marked as offline). Shortly after, I noticed I can't even ping the machine that owns the printer (I also can not remotely access it in any other way I've tried). Currently I'm trying to ping the machine from the router both computers are connected to (and my machine in question doesn't answer). I do receive the echo requests (as verified with WireShark). I also added a rule in the Windows Firewall to specifically allow ICMP echo requests, but that didn't change anything. I also tried netsh firewall set icmpsetting 8 enable, but that didn't change anything either. Completely disabling the Windows Firewall has no effect on the issue either. One has to wonder, where does Windows log when and why it ignored any incoming packets? How can I get to the bottom of this? Here are some ways I found to dig deeper into the issue: Enabling logging on the Windows Firewall Enabling Windows Filtering Platform Auditing Both methods at least give more insight into the issue. The plain log file is full of entries like this: 2011-11-11 14:35:27 DROP ICMP 192.168.133.1 192.168.133.128 - - 84 - - - - 8 0 - RECEIVE So the ICMP packets are being dropped as if that was intended. The Event Viewer now gives a little bit more details: The Windows Filtering Platform has blocked a packet. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 192.168.133.1 Source Port: 0 Destination Address: 192.168.133.128 Destination Port: 8 Protocol: 1 Filter Information: Filter Run-Time ID: 214517 Layer Name: Receive/Accept Layer Run-Time ID: 44 This same entry is always repeated with 2 points of information changing: Process ID: 420 Application Name: \device\harddiskvolume2\windows\system32\svchost.exe The service host with the PID 420 is the host for the following services: Windows Audio DHCP Client Windows Event Log HomeGroup Provider TCP/IP NetBIOS Helper Security Center Additionally, there is currently this problem with the same machine: Even though my network is set to be a "Home network", I am unable to create a new homegroup.

  Read the article

• Ubuntu won't boot from USB memory stick

  - by mackenir

  I used the instructions on this webpage to create a bootable USB drive for running Ubuntu 9.10. Unfortunately it doesn't work on my EeePC. Even with 'Removable Dev.' selected in the BIOS as the first boot device, the PC just boots into Windows 7. How do I troubleshoot this problem? The drive is readable and looks like this: Directory of E:\ 28/10/2009 21:14 <DIR> .disk 28/10/2009 21:14 222 README.diskdefines 28/10/2009 21:14 143 autorun.inf 28/10/2009 21:14 <DIR> casper 28/10/2009 21:14 <DIR> dists 28/10/2009 21:14 <DIR> install 28/10/2009 21:14 <DIR> syslinux 28/10/2009 21:14 4,098 md5sum.txt 28/10/2009 21:14 <DIR> pics 28/10/2009 21:14 <DIR> pool 28/10/2009 21:14 <DIR> preseed 28/10/2009 21:14 0 ubuntu 26/10/2009 16:16 1,468,640 wubi.exe 25/02/2010 00:28 2,147,483,648 casper-rw 8 Dir(s) 5,290,307,584 bytes free

  Read the article

• How to configure a trusted connection between IIS 7 and SQL Server 2005?

  - by user1180652

  How do configure a trusted connection between IIS 7 and SQL Server 2005? My webapp was working fine with Windows Authentication enabled in IIS. Now, in order to solve a problem, we need to use a trusted connection. Unfortunately, enabling the trusted connection in the web.config broke the webapp. Oddly enough, when I run this application with trusted connection from my local dev machine (using the Cassini web server) IIS (Windows Server 2008) is running on one machine. The database (SQL Server 2005 but could migrate to 2008) is running on another machine. We are on a Windows domain running AD. All traffic is within our own firewall - no public access. Beyond that, I can't provide much info but I can find it. We're very "compartmentalized" (we have server people, security people, oracle people, SQL Server people, etc.) Thanks! Update 02/14/2012 0902: The webapp is now functional (app no longer broken) but the main issue is still unresolved. Now I have the app's application pool running as a domain account with permissions on the SQL Server box and IIS box. We were using this account to run the application but, and here's the problem, we need to log the real user name that made a change. When using the service account, the name of that service account appeared in the audit tables, making the auditing quite useless. So, not I'm at least running again. The connection string in the web.config is using "Trusted_Connection=True", the appPool is using a domain account with access to both boxes, BUT when I make a change (logged in as me) the name of the service account (appPool identity) is still logged in the audit tables. I also manually granted full permissions to the service account on the webapp folder. What do I need to do in order to log my name, not the service account, in the audit tables? Everything I'm reading says I need to establish a trusted connection between the two servers.

  Read the article

• Does the same lame settings (--alt-preset standard) have differrent names?

  - by erikric

  I've always used windows, and therefore EAC to rip my CDs, but since I've started using Ubuntu more often, I decided to try to rip some albums there. I ended up using k3b (since I found it in the Ubuntu Software center. Tried to install RubyRipper first, but when 'sudo apt-get install ' or UDC fails, a Windows user like me is lost) The real question here is about the settings for the lame encoder. I'm used to just writing --alt-preset standard, and everything works like a charm, but the default in k3b look like this: lame -r --bitwidth 16 --little-endian -s 44.1 -h --tt %t --ta %a --tl %m --ty %y --tc %c --tn %n - %f I assume these are some sensible lame settings, and not a malicious perl script (although it looks like it). It seems to me like some of these ought to be there, and that I can not overwrite the whole thing with my good ol' --alt-preset. So, the question is do I need to replace anything, or is -h the same as old --alt-preset? Is it a difference between '--preset standard' and '--alt-preset standard'? And are those the same as -V 2?

  Read the article

• iperf max udp multicast performance peaking at 10Mbit/s?

  - by Tom Frey

  I'm trying to test UDP multicast throughput via iperf but it seems like it's not sending more than 10Mbit/s from my dev machine: C:\> iperf -c 224.0.166.111 -u -T 1 -t 100 -i 1 -b 1000000000 ------------------------------------------------------------ Client connecting to 224.0.166.111, UDP port 5001 Sending 1470 byte datagrams Setting multicast TTL to 1 UDP buffer size: 8.00 KByte (default) ------------------------------------------------------------ [156] local 192.168.1.99 port 49693 connected with 224.0.166.111 port 5001 [ ID] Interval Transfer Bandwidth [156] 0.0- 1.0 sec 1.22 MBytes 10.2 Mbits/sec [156] 1.0- 2.0 sec 1.14 MBytes 9.57 Mbits/sec [156] 2.0- 3.0 sec 1.14 MBytes 9.55 Mbits/sec [156] 3.0- 4.0 sec 1.14 MBytes 9.56 Mbits/sec [156] 4.0- 5.0 sec 1.14 MBytes 9.56 Mbits/sec [156] 5.0- 6.0 sec 1.15 MBytes 9.62 Mbits/sec [156] 6.0- 7.0 sec 1.14 MBytes 9.53 Mbits/sec When I run it on another server, I'm getting ~80Mbit/s which is quite a bit better but still not anywhere near the 1Gbps limits that I should be getting? C:\> iperf -c 224.0.166.111 -u -T 1 -t 100 -i 1 -b 1000000000 ------------------------------------------------------------ Client connecting to 224.0.166.111, UDP port 5001 Sending 1470 byte datagrams Setting multicast TTL to 1 UDP buffer size: 8.00 KByte (default) ------------------------------------------------------------ [180] local 10.0.101.102 port 51559 connected with 224.0.166.111 port 5001 [ ID] Interval Transfer Bandwidth [180] 0.0- 1.0 sec 8.60 MBytes 72.1 Mbits/sec [180] 1.0- 2.0 sec 8.73 MBytes 73.2 Mbits/sec [180] 2.0- 3.0 sec 8.76 MBytes 73.5 Mbits/sec [180] 3.0- 4.0 sec 9.58 MBytes 80.3 Mbits/sec [180] 4.0- 5.0 sec 9.95 MBytes 83.4 Mbits/sec [180] 5.0- 6.0 sec 10.5 MBytes 87.9 Mbits/sec [180] 6.0- 7.0 sec 10.9 MBytes 91.1 Mbits/sec [180] 7.0- 8.0 sec 11.2 MBytes 94.0 Mbits/sec Anybody has any idea why this is not achieving close to link limits (1Gbps)? Thanks, Tom

  Read the article

• GitLab post-receive hook not firing

  - by Ben Graham

  Apologies if this isn't the right stackexchange. I have a GitLab install. It was installed over the top of a gitolite install that was only a few days old, and I assume this non-standard setup is at the root of my problem, but I cannot pin it down. The problem is straightforward: post-receive hooks are not fired. This prevents 'project activity' appearing in GitLab. The problem looks like: $ git push #... error: cannot run hooks/post-receive: No such file or directory Hook Exists The post-receive hook/symlink exists and is executable: -rwxr-xr-x 1 git git 470 Oct 3 2012 .gitolite/hooks/common/post-receive lrwxrwxrwx 1 git git 45 Oct 3 2012 repositories/project.git/hooks/post-receive -> /home/git/.gitolite/hooks/common/post-receive It's Executable By GitLab The gitlab user can execute the script (I have removed the /dev/null redirect and fed in blank input to get an 'OK' as output): sudo su - gitlab -c /home/git/.gitolite/hooks/common/post-receive OK GitLab Can Find It GitLab is looking for hooks in the correct location: $ grep hooks /srv/gitlab/gitlab/config/gitlab.yml hooks_path: /home/git/.gitolite/hooks/ and $ bundle exec rake gitlab:app:status RAILS_ENV=production # ... /home/git/.gitolite/hooks/common/post-receive exists? ............YES Environment The env -i line in the hook is commonly cited as an issue. I think that would occur after this problem, but for completeness, redis-cli is found OK: $ env -i redis-cli redis> I've run out of debugging ideas on this one. Does anybody have any suggestions?

  Read the article

• SVN, Samba and Symbolic Links. How to get them all to play together?

  - by Camsoft

  I've got a website project under version control that relies on files from an unversioned directory on the same server via Symbolic Links. I'm currently storing the symbolic links in the repository. The idea is that if someone checks out a working copy on to the same server they can edit and test the working copy of the project before committing it back to the repository. When they checkout their working copy it successfully sets up the symlinks so that the entire site works when testing. The users that work on the project are Windows users, so I've set a samba shares on the server and then mapped them to network drives in Windows. People can edit their working copies directly on the server via network shares and then test them in the web browser before committing their changes back to the repository via TortoiseSVN. The Problem The problem I have is that Samba resolves the symlinks as expected but when a user tries to commit their changes back to the repository, TortoiseSVN thinks the linked files are part of the project and tries to commit the target files to the repository and not the symlinks themselves. I tried turning off symlink support in samba which means that the linked files cannot be resolved as I don't really want people to have access to the linked files nor do I want to import the linked files in the repository. The problem with this is that I get Can't stat '\webserver\projects\working\project\symlinked_file.php'. Access is denied Apart from the symlink problem everything else works 100% perfectly. Users can either checkout website projects to their machine and work on them (but can't test) or checkout them out to their space on the dev web server and work on them and fully test. So I don't want to change the workflow process, I just need a solution to the symbolic link issue. Many thanks. Originally posted on StackOverflow: http://stackoverflow.com/questions/2400917/svn-samba-and-symbolic-links-how-to-get-them-all-to-play-together

  Read the article

< Previous Page | 441 442 443 444 445 446 447 448 449 450 451 452  | Next Page >