Search Results

Search found 11618 results on 465 pages for 'shared storage'.

Page 446/465 | < Previous Page | 442 443 444 445 446 447 448 449 450 451 452 453  | Next Page >

• DRBD Not syncing between my nodes

  - by Mike Curry

  Some version info: Operating system is Ubuntu 11.10, on EC2, kernel is 3.0.0-16-virtual and the application info is: Version: 8.3.11 (api:88) GIT-hash: 0de839cee13a4160eed6037c4bddd066645e23c5 build by buildd@allspice, 2011-07-05 19:51:07 Getting some strange errors in dmesg (seen below) as well, there is no replication happening. I have made my first node primary and its showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Primary/Unknown UpToDate/DUnknown r----s ext3 my secondary node is showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Secondary/Unknown Inconsistent/DUnknown r----s Showing /proc/drbd on the master shows: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Primary/Unknown ds:UpToDate/DUnknown r----s ns:0 nr:0 dw:4 dr:1073 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Showing /proc/drbd on the slave shows that there is nothing being transfered... version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Secondary/Unknown ds:Inconsistent/DUnknown r----s ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Here is my config... resource r0 { protocol C; startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "test123; } on drbd01 { device /dev/drbd0; disk /dev/xvdm; address 23.XX.XX.XX:7788; # blocked out ip meta-disk internal; } on drbd02 { device /dev/drbd0; disk /dev/xvdm; address 184.XX.XX.XX:7788; #blocked out ip meta-disk internal; } } I have run the following on the master: sudo drbdadm -- --overwrite-data-of-peer primary all There is no firewall between the systems. Here is the dmesg with some errors: [2285172.969955] drbd: initialized. Version: 8.3.11 (api:88/proto:86-96) [2285172.969960] drbd: srcversion: DA5A13F16DE6553FC7CE9B2 [2285172.969962] drbd: registered as block device major 147 [2285172.969965] drbd: minor_table @ 0xffff88000276ea00 [2285173.000952] block drbd0: Starting worker thread (from drbdsetup [1300]) [2285173.003971] block drbd0: disk( Diskless -> Attaching ) [2285173.006150] block drbd0: No usable activity log found. [2285173.006154] block drbd0: Method to ensure write ordering: flush [2285173.006158] block drbd0: max BIO size = 4096 [2285173.006165] block drbd0: drbd_bm_resize called with capacity == 524271928 [2285173.008512] block drbd0: resync bitmap: bits=65533991 words=1023969 pages=2000 [2285173.008518] block drbd0: size = 250 GB (262135964 KB) [2285173.079566] block drbd0: bitmap READ of 2000 pages took 17 jiffies [2285173.081189] block drbd0: recounting of set bits took additional 1 jiffies [2285173.081194] block drbd0: 250 GB (65533991 bits) marked out-of-sync by on disk bit-map. [2285173.081203] block drbd0: Suspended AL updates [2285173.081210] block drbd0: disk( Attaching -> UpToDate ) [2285173.081214] block drbd0: attached to UUIDs 1C1291D39584C1D1:0000000000000004:0000000000000000:0000000000000000 [2285173.095016] block drbd0: conn( StandAlone -> Unconnected ) [2285173.095046] block drbd0: Starting receiver thread (from drbd0_worker [1301]) [2285173.099297] block drbd0: receiver (re)started [2285173.099304] block drbd0: conn( Unconnected -> WFConnection ) [2285173.099330] block drbd0: bind before connect failed, err = -99 [2285173.099346] block drbd0: conn( WFConnection -> Disconnecting ) [2285173.295788] block drbd0: Discarding network configuration. [2285173.295815] block drbd0: Connection closed [2285173.295826] block drbd0: conn( Disconnecting -> StandAlone ) [2285173.295840] block drbd0: receiver terminated [2285173.295844] block drbd0: Terminating drbd0_receiver Edit: Reading some other similar issues, it was suggested to do a 'drbdadm dump all', so I figured it couldn't hurt. ubuntu@drbd01:~$ drbdadm dump all /etc/drbd.conf:19: in resource r0, on drbd01: IP 23.XX.XX.XX not found on this host. and on slave: root@drbd02:~# drbdadm dump all /etc/drbd.conf:25: in resource r0, on drbd02: IP 184.XX.XX.XX not found on this host. Strange it doesn't find its own ip, however, this is an Amazon EC2 system using an elastic IP... here are my ipconfigs for both... master: ubuntu@drbd01:~$ ifconfig eth0 Link encap:Ethernet HWaddr 22:00:0a:1c:27:11 inet addr:10.28.39.17 Bcast:10.28.39.63 Mask:255.255.255.192 inet6 addr: fe80::2000:aff:fe1c:2711/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1569 errors:0 dropped:0 overruns:0 frame:0 TX packets:1169 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:124409 (124.4 KB) TX bytes:213601 (213.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) slave: root@drbd02:~# ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3f:00:14:9d inet addr:10.160.27.107 Bcast:10.160.27.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3fff:fe00:149d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:774 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:75381 (75.3 KB) TX bytes:109673 (109.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

  Read the article

• Missing audio and problems playing FLV video converted from 720p .mov file with FFMPEG

  - by undefined

  I have some .mov video files recorded from a JVC GC-FM1 HD video camera in 720p mode. I have FFMPEG running on a Linux box that I upload files to and have them encoded into FLV format. The video appears to be encoding ok but there is no audio in the resulting FLV file and when I play it back in Flash Player in a browser or on Adobe Media Player, the video pauses at the start. It appears that Adobe Media Player waits for the progress bar to reach the end of the video before starting the playback - i.e. the video will load, the picture pauses, the progress bar seeks to the end as if the video was playing then when it reaches the end the video picture starts. There is no audio on the video. I am noticing this in the video player I have built with Flash 8 using an FLVPlayback component and attached seekBar. The seek bar will start moving as if the video is playing but the picture remains paused. Here are some outputs from my FFMPEG log and the command I am using to encode the video - my FFMPEG command called from PHP - $cmd = 'ffmpeg -i ' . $sourcelocation.$filename.".".$fileext . ' -ab 96k -b 700k -ar 44100 -s ' . $target['width'] . 'x' . $target['height'] . ' -ac 1 -acodec libfaac ' . $destlocation.$filename.$ext_trans .' 2>&1'; and here is the output from my error log - FFmpeg version UNKNOWN, Copyright (c) 2000-2010 Fabrice Bellard, et al. built on Jan 22 2010 11:31:03 with gcc 4.1.2 20070925 (Red Hat 4.1.2-33) configuration: --prefix=/usr --enable-static --enable-shared --enable-gpl --enable-nonfree --enable-postproc --enable-avfilter --enable-avfilter-lavf --enable-libfaac --enable-libfaad --enable-libfaadbin --enable-libgsm --enable-libmp3lame --enable-libvorbis --enable-libx264 libavutil 50. 7. 0 / 50. 7. 0 libavcodec 52.48. 0 / 52.48. 0 libavformat 52.47. 0 / 52.47. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.17. 0 / 1.17. 0 libswscale 0. 9. 0 / 0. 9. 0 libpostproc 51. 2. 0 / 51. 2. 0 Seems stream 0 codec frame rate differs from container frame rate: 119.88 (120000/1001) -> 59.94 (60000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'uploads/video/60974_v1.mov': Metadata: major_brand : qt minor_version : 0 compatible_brands: qt comment : JVC GC-FM1 comment-eng : JVC GC-FM1 Duration: 00:00:30.41, start: 0.000000, bitrate: 4158 kb/s Stream #0.0(eng): Video: h264, yuv420p, 640x480 [PAR 1:1 DAR 4:3], 4017 kb/s, 59.94 fps, 59.94 tbr, 90k tbn, 119.88 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Output #0, rawvideo, to 'uploads/video/60974_v1.jpg': Stream #0.0(eng): Video: mjpeg, yuvj420p, 320x240 [PAR 1:1 DAR 4:3], q=2-31, 200 kb/s, 90k tbn, 59.94 tbc Stream mapping: Stream #0.0 -> #0.0 Press [q] to stop encoding [h264 @ 0x8e67930]B picture before any references, skipping [h264 @ 0x8e67930]decode_slice_header error [h264 @ 0x8e67930]no frame! Error while decoding stream #0.0 [h264 @ 0x8e67930]B picture before any references, skipping [h264 @ 0x8e67930]decode_slice_header error [h264 @ 0x8e67930]no frame! Error while decoding stream #0.0 frame= 1 fps= 0 q=3.8 Lsize= 15kB time=0.02 bitrate=7271.4kbits/s dup=482 drop=0 video:15kB audio:0kB global headers:0kB muxing overhead 0.000000% Which are the important errors here - B picture before any references, skipping? decode_slice_header error? no frame? or Seems stream 0 codec frame rate differs from container frame rate: 119.88 (120000/1001) - 59.94 (60000/1001) Any advice welcome, thanks

  Read the article

• ASP.NET MVC 2 - Saving child entities on form submit

  - by Justin

  Hey, I'm using ASP.NET MVC 2 and am struggling with saving child entities. I have an existing Invoice entity (which I create on a separate form) and then I have a LogHours view that I'd like to use to save InvoiceLog's, which are child entities of Invoice. Here's the view: <%@ Page Title="" Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage<TothSolutions.Data.Invoice>" %> <asp:Content ID="Content1" ContentPlaceHolderID="TitleContent" runat="server"> Log Hours </asp:Content> <asp:Content ID="Content3" ContentPlaceHolderID="HeadContent" runat="server"> <script type="text/javascript"> $(document).ready(function () { $("#InvoiceLogs_0__Description").focus(); }); </script> </asp:Content> <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> <h2>Log Hours</h2> <% using (Html.BeginForm("SaveHours", "Invoices")) {%> <%: Html.ValidationSummary(true) %> <fieldset> <legend>Fields</legend> <table> <tr> <th>Date</th> <th>Description</th> <th>Hours</th> </tr> <% int index = 0; foreach (var log in Model.InvoiceLogs) { %> <tr> <td><%: log.LogDate.ToShortDateString() %></td> <td><%: Html.TextBox("InvoiceLogs[" + index + "].Description")%></td> <td><%: Html.TextBox("InvoiceLogs[" + index + "].Hours")%></td> <td>Hours</td> </tr> <% index++; } %> </table> <p> <%: Html.Hidden("InvoiceID") %> <%: Html.Hidden("CreateDate") %> <input type="submit" value="Save" /> </p> </fieldset> <% } %> <div> <%: Html.ActionLink("Back to List", "Index") %> </div> </asp:Content> And here's the controller code: //GET: /Secure/Invoices/LogHours/ public ActionResult LogHours(int id) { var invoice = DataContext.InvoiceData.Get(id); if (invoice == null) { throw new Exception("Invoice not found with id: " + id); } return View(invoice); } //POST: /Secure/Invoices/SaveHours/ [AcceptVerbs(HttpVerbs.Post)] public ActionResult SaveHours([Bind(Exclude = "InvoiceLogs")]Invoice invoice) { TryUpdateModel(invoice.InvoiceLogs, "InvoiceLogs"); invoice.UpdateDate = DateTime.Now; invoice.DeveloperID = DeveloperID; //attaching existing invoice. DataContext.InvoiceData.Attach(invoice); //save changes. DataContext.SaveChanges(); //redirect to invoice list. return RedirectToAction("Index"); } And the data access code: public static void Attach(Invoice invoice) { var i = new Invoice { InvoiceID = invoice.InvoiceID }; db.Invoices.Attach(i); db.Invoices.ApplyCurrentValues(invoice); } In the SaveHours action, it properly sets the values of the InvoiceLog entities after I call TryUpdateModel but when it does SaveChanges it doesn't update the database with the new values. Also, if you manually update the values of the InvoiceLog entries in the database and then go to this page it doesn't populate the textboxes so it's clearly not binding correctly. Thanks, Justin

  Read the article

• Login loop in Snow Leopard

  - by hgpc

  I can't get out of a login loop of a particular admin user. After entering the password the login screen is shown again after about a minute. Other users work fine. It started happening after a simple reboot. Can you please help me? Thank you! Tried to no avail: Change the password Remove the password Repair disk (no errors) Boot in safe mode Reinstall Snow Leopard and updating to 10.6.6 Remove content of ~/Library/Caches Removed content of ~/Library/Preferences Replaced /etc/authorization with Install DVD copy The system.log mentions a crash report. I'm including both below. system.log Jan 8 02:43:30 loginwindow218: Login Window - Returned from Security Agent Jan 8 02:43:30 loginwindow218: USER_PROCESS: 218 console Jan 8 02:44:42 kernel[0]: Jan 8 02:44:43: --- last message repeated 1 time --- Jan 8 02:44:43 com.apple.launchd[1] (com.apple.loginwindow218): Job appears to have crashed: Bus error Jan 8 02:44:43 com.apple.UserEventAgent-LoginWindow223: ALF error: cannot find useragent 1102 Jan 8 02:44:43 com.apple.UserEventAgent-LoginWindow223: plugin.UserEventAgentFactory: called with typeID=FC86416D-6164-2070-726F-70735C216EC0 Jan 8 02:44:43 /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow233: Login Window Application Started Jan 8 02:44:43 SecurityAgent228: CGSShutdownServerConnections: Detaching application from window server Jan 8 02:44:43 com.apple.ReportCrash.Root232: 2011-01-08 02:44:43.936 ReportCrash232:2903 Saved crash report for loginwindow218 version ??? (???) to /Library/Logs/DiagnosticReports/loginwindow_2011-01-08-024443_localhost.crash Jan 8 02:44:44 SecurityAgent228: MIG: server died: CGSReleaseShmem : Cannot release shared memory Jan 8 02:44:44 SecurityAgent228: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Jan 8 02:44:44 SecurityAgent228: CGSDisplayServerShutdown: Detaching display subsystem from window server Jan 8 02:44:44 SecurityAgent228: HIToolbox: received notification of WindowServer event port death. Jan 8 02:44:44 SecurityAgent228: port matched the WindowServer port created in BindCGSToRunLoop Jan 8 02:44:44 loginwindow233: Login Window Started Security Agent Jan 8 02:44:44 WindowServer234: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Jan 8 02:44:44 com.apple.WindowServer234: Sat Jan 8 02:44:44 .local WindowServer234 <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Jan 8 02:44:54 SecurityAgent243: NSSecureTextFieldCell detected a field editor ((null)) that is not a NSTextView subclass designed to work with the cell. Ignoring... Crash report Process: loginwindow 218 Path: /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow Identifier: loginwindow Version: ??? (???) Code Type: X86-64 (Native) Parent Process: launchd [1] Date/Time: 2011-01-08 02:44:42.748 +0100 OS Version: Mac OS X 10.6.6 (10J567) Report Version: 6 Exception Type: EXC_BAD_ACCESS (SIGBUS) Exception Codes: 0x000000000000000a, 0x000000010075b000 Crashed Thread: 0 Dispatch queue: com.apple.main-thread Thread 0 Crashed: Dispatch queue: com.apple.main-thread 0 com.apple.security 0x00007fff801c6e8b Security::ReadSection::at(unsigned int) const + 25 1 com.apple.security 0x00007fff801c632f Security::DbVersion::open() + 123 2 com.apple.security 0x00007fff801c5e41 Security::DbVersion::DbVersion(Security::AppleDatabase const&, Security::RefPointer<Security::AtomicBufferedFile> const&) + 179 3 com.apple.security 0x00007fff801c594e Security::DbModifier::getDbVersion(bool) + 330 4 com.apple.security 0x00007fff801c57f5 Security::DbModifier::openDatabase() + 33 5 com.apple.security 0x00007fff801c5439 Security::Database::_dbOpen(Security::DatabaseSession&, unsigned int, Security::AccessCredentials const*, void const*) + 221 6 com.apple.security 0x00007fff801c4841 Security::DatabaseManager::dbOpen(Security::DatabaseSession&, Security::DbName const&, unsigned int, Security::AccessCredentials const*, void const*) + 77 7 com.apple.security 0x00007fff801c4723 Security::DatabaseSession::DbOpen(char const*, cssm_net_address const*, unsigned int, Security::AccessCredentials const*, void const*, long&) + 285 8 com.apple.security 0x00007fff801d8414 cssm_DbOpen(long, char const*, cssm_net_address const*, unsigned int, cssm_access_credentials const*, void const*, long*) + 108 9 com.apple.security 0x00007fff801d7fba CSSM_DL_DbOpen + 106 10 com.apple.security 0x00007fff801d62f6 Security::CssmClient::DbImpl::open() + 162 11 com.apple.security 0x00007fff801d8977 SSDatabaseImpl::open(Security::DLDbIdentifier const&) + 53 12 com.apple.security 0x00007fff801d8715 SSDLSession::DbOpen(char const*, cssm_net_address const*, unsigned int, Security::AccessCredentials const*, void const*, long&) + 263 13 com.apple.security 0x00007fff801d8414 cssm_DbOpen(long, char const*, cssm_net_address const*, unsigned int, cssm_access_credentials const*, void const*, long*) + 108 14 com.apple.security 0x00007fff801d7fba CSSM_DL_DbOpen + 106 15 com.apple.security 0x00007fff801d62f6 Security::CssmClient::DbImpl::open() + 162 16 com.apple.security 0x00007fff802fa786 Security::CssmClient::DbImpl::unlock(cssm_data const&) + 28 17 com.apple.security 0x00007fff80275b5d Security::KeychainCore::KeychainImpl::unlock(Security::CssmData const&) + 89 18 com.apple.security 0x00007fff80291a06 Security::KeychainCore::StorageManager::login(unsigned int, void const*, unsigned int, void const*) + 3336 19 com.apple.security 0x00007fff802854d3 SecKeychainLogin + 91 20 com.apple.loginwindow 0x000000010000dfc5 0x100000000 + 57285 21 com.apple.loginwindow 0x000000010000cfb4 0x100000000 + 53172 22 com.apple.Foundation 0x00007fff8721e44f __NSThreadPerformPerform + 219 23 com.apple.CoreFoundation 0x00007fff82627401 __CFRunLoopDoSources0 + 1361 24 com.apple.CoreFoundation 0x00007fff826255f9 __CFRunLoopRun + 873 25 com.apple.CoreFoundation 0x00007fff82624dbf CFRunLoopRunSpecific + 575 26 com.apple.HIToolbox 0x00007fff8444493a RunCurrentEventLoopInMode + 333 27 com.apple.HIToolbox 0x00007fff8444473f ReceiveNextEventCommon + 310 28 com.apple.HIToolbox 0x00007fff844445f8 BlockUntilNextEventMatchingListInMode + 59 29 com.apple.AppKit 0x00007fff80b01e64 _DPSNextEvent + 718 30 com.apple.AppKit 0x00007fff80b017a9 -NSApplication nextEventMatchingMask:untilDate:inMode:dequeue: + 155 31 com.apple.AppKit 0x00007fff80ac748b -NSApplication run + 395 32 com.apple.loginwindow 0x0000000100004b16 0x100000000 + 19222 33 com.apple.loginwindow 0x0000000100004580 0x100000000 + 17792 Thread 1: Dispatch queue: com.apple.libdispatch-manager 0 libSystem.B.dylib 0x00007fff8755216a kevent + 10 1 libSystem.B.dylib 0x00007fff8755403d _dispatch_mgr_invoke + 154 2 libSystem.B.dylib 0x00007fff87553d14 _dispatch_queue_invoke + 185 3 libSystem.B.dylib 0x00007fff8755383e _dispatch_worker_thread2 + 252 4 libSystem.B.dylib 0x00007fff87553168 _pthread_wqthread + 353 5 libSystem.B.dylib 0x00007fff87553005 start_wqthread + 13 Thread 0 crashed with X86 Thread State (64-bit): rax: 0x000000010075b000 rbx: 0x00007fff5fbfd990 rcx: 0x00007fff875439da rdx: 0x0000000000000000 rdi: 0x00007fff5fbfd990 rsi: 0x0000000000000000 rbp: 0x00007fff5fbfd5d0 rsp: 0x00007fff5fbfd5d0 r8: 0x0000000000000007 r9: 0x0000000000000000 r10: 0x00007fff8753beda r11: 0x0000000000000202 r12: 0x0000000100133e78 r13: 0x00007fff5fbfda50 r14: 0x00007fff5fbfda50 r15: 0x00007fff5fbfdaa0 rip: 0x00007fff801c6e8b rfl: 0x0000000000010287 cr2: 0x000000010075b000

  Read the article

• AppDomain dependencies across directories

  - by strager

  I am creating a plugin system and I am creating one AppDomain per plugin. Each plugin has its own directory with its main assemblies and references. The main assemblies will be loaded by my plugin loader, in addition to my interface assemblies (so the plugin can interact with the application). Creating the AppDomain: this.appDomain = AppDomain.CreateDomain("AppDomain", null, new AppDomainSetup { ApplicationBase = pluginPath, PrivateBinPath = pluginPath, }); Loading the assemblies: this.appDomain.Load(myInterfaceAssembly.GetName(true)); var assemblies = new List<Assembly>(); foreach (var assemblyName in this.assemblyNames) { assemblies.Add(this.appDomain.Load(assemblyName)); } The format of assemblyName is the assembly's filename without ".dll". The problem is that AppDomain.Load(assemblyName) throws an exception: Could not load file or assembly '[[assemblyName]], Version=1.0.0.0, Culture=neutral, PublicKeyToken=null' or one of its dependencies. The system cannot find the file specified. All of the dependencies of [[assemblyName]] are: Inside the directory pluginPath, The myInterfaceAssembly which is already loaded, or In the GAC (e.g. mscorelib). Clearly I'm not doing something right. I have tried: Creating an object using this.appDomain.CreateInstanceAndUnwrap inheriting from MarshalByRefObject with a LoadAssembly method to load the assembly. I get an exception saying that the current assembly (containing the proxy class) could not be loaded (file not found, as above), even if I manually call this.appDomain.Load(Assembly.GetExecutingAssembly().GetName(true)). Attaching an AssemblyResolve handler to this.appDomain. I'm met with the same exception as in (1), and manually loading doesn't help. Recursively loading assemblies by loading their dependencies into this.appDomain first. This doesn't work, but I doubt my code is correct: private static void LoadAssemblyInto(AssemblyName assemblyName, AppDomain appDomain) { var assembly = Assembly.Load(assemblyName); foreach (var referenceName in assembly.GetReferencedAssemblies()) { if (!referenceName.FullName.StartsWith("MyProject")) { continue; } var loadedAssemblies = appDomain.GetAssemblies(); if (loadedAssemblies.Any((asm) => asm.FullName == referenceName.FullName)) { continue; } LoadAssemblyInto(referenceName, appDomain); } appDomain.Load(assembly.GetName(true)); } How can I load my plugin assembly with its dependencies in that plugin's directory while also loading some assemblies in the current directory? Note: The assemblies a plugin may (probably will) reference are already loaded in the current domain. This can be shared across domains (performance benefit? simplicity?) if required. Fusion log: *** Assembly Binder Log Entry (12/24/2010 @ 10:46:40 AM) *** The operation failed. Bind result: hr = 0x80070002. The system cannot find the file specified. Assembly manager loaded from: C:\Windows\Microsoft.NET\Framework\v4.0.30319\clr.dll Running under executable C:\MyProject\bin\Debug\MyProject.vshost.exe --- A detailed error log follows. LOG: Start binding of native image vshost32, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a, processorArchitecture=x86. WRN: No matching native image found. LOG: Bind to native image assembly did not succeed. Use IL image. LOG: IL assembly loaded from C:\MyProject\bin\Debug\MyProject.vshost.exe

  Read the article

• Mysql performance problem & Failed DIMM

  - by murdoch

  Hi I have a dedicated mysql database server which has been having some performance problems recently, under normal load the server will be running fine, then suddenly out of the blue the performance will fall off a cliff. The server isn't using the swap file and there is 12GB of RAM in the server, more than enough for its needs. After contacting my hosting comapnies support they have discovered that there is a failed 2GB DIMM in the server and have scheduled to replace it tomorow morning. My question is could a failed DIMM result in the performance problems I am seeing or is this just coincidence? My worry is that they will replace the ram tomorrow but the problems will persist and I will still be lost of explanations so I am just trying to think ahead. The reason I ask is that there is plenty of RAM in the server, more than required and simply missing 2GB should be a problem, so if this failed DIMM is causing these performance problems then the OS must be trying to access the failed DIMM and slowing down as a result. Does that sound like a credible explanation? This is what DELLs omreport program says about the RAM, notice one dimm is "Critical" Memory Information Health : Critical Memory Operating Mode Fail Over State : Inactive Memory Operating Mode Configuration : Optimizer Attributes of Memory Array(s) Attributes : Location Memory Array 1 : System Board or Motherboard Attributes : Use Memory Array 1 : System Memory Attributes : Installed Capacity Memory Array 1 : 12288 MB Attributes : Maximum Capacity Memory Array 1 : 196608 MB Attributes : Slots Available Memory Array 1 : 18 Attributes : Slots Used Memory Array 1 : 6 Attributes : ECC Type Memory Array 1 : Multibit ECC Total of Memory Array(s) Attributes : Total Installed Capacity Value : 12288 MB Attributes : Total Installed Capacity Available to the OS Value : 12004 MB Attributes : Total Maximum Capacity Value : 196608 MB Details of Memory Array 1 Index : 0 Status : Ok Connector Name : DIMM_A1 Type : DDR3-Registered Size : 2048 MB Index : 1 Status : Ok Connector Name : DIMM_A2 Type : DDR3-Registered Size : 2048 MB Index : 2 Status : Ok Connector Name : DIMM_A3 Type : DDR3-Registered Size : 2048 MB Index : 3 Status : Critical Connector Name : DIMM_B1 Type : DDR3-Registered Size : 2048 MB Index : 4 Status : Ok Connector Name : DIMM_B2 Type : DDR3-Registered Size : 2048 MB Index : 5 Status : Ok Connector Name : DIMM_B3 Type : DDR3-Registered Size : 2048 MB the command free -m shows this, the server seems to be using more than 10GB of ram which would suggest it is trying to use the DIMM total used free shared buffers cached Mem: 12004 10766 1238 0 384 4809 -/+ buffers/cache: 5572 6432 Swap: 2047 0 2047 iostat output while problem is occuring avg-cpu: %user %nice %system %iowait %steal %idle 52.82 0.00 11.01 0.00 0.00 36.17 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 47.00 0.00 576.00 0 576 sda1 0.00 0.00 0.00 0 0 sda2 1.00 0.00 32.00 0 32 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 46.00 0.00 544.00 0 544 avg-cpu: %user %nice %system %iowait %steal %idle 53.12 0.00 7.81 0.00 0.00 39.06 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 49.00 0.00 592.00 0 592 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 49.00 0.00 592.00 0 592 avg-cpu: %user %nice %system %iowait %steal %idle 56.09 0.00 7.43 0.37 0.00 36.10 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 232.00 0.00 64520.00 0 64520 sda1 0.00 0.00 0.00 0 0 sda2 159.00 0.00 63728.00 0 63728 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 73.00 0.00 792.00 0 792 avg-cpu: %user %nice %system %iowait %steal %idle 52.18 0.00 9.24 0.06 0.00 38.51 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 49.00 0.00 600.00 0 600 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 49.00 0.00 600.00 0 600 avg-cpu: %user %nice %system %iowait %steal %idle 54.82 0.00 8.64 0.00 0.00 36.55 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 100.00 0.00 2168.00 0 2168 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 100.00 0.00 2168.00 0 2168 avg-cpu: %user %nice %system %iowait %steal %idle 54.78 0.00 6.75 0.00 0.00 38.48 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 84.00 0.00 896.00 0 896 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 84.00 0.00 896.00 0 896 avg-cpu: %user %nice %system %iowait %steal %idle 54.34 0.00 7.31 0.00 0.00 38.35 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 81.00 0.00 840.00 0 840 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 81.00 0.00 840.00 0 840 avg-cpu: %user %nice %system %iowait %steal %idle 55.18 0.00 5.81 0.44 0.00 38.58 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 317.00 0.00 105632.00 0 105632 sda1 0.00 0.00 0.00 0 0 sda2 224.00 0.00 104672.00 0 104672 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 93.00 0.00 960.00 0 960 avg-cpu: %user %nice %system %iowait %steal %idle 55.38 0.00 7.63 0.00 0.00 36.98 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 74.00 0.00 800.00 0 800 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 74.00 0.00 800.00 0 800 avg-cpu: %user %nice %system %iowait %steal %idle 56.43 0.00 7.80 0.00 0.00 35.77 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 72.00 0.00 784.00 0 784 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 72.00 0.00 784.00 0 784 avg-cpu: %user %nice %system %iowait %steal %idle 54.87 0.00 6.49 0.00 0.00 38.64 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 80.20 0.00 855.45 0 864 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 80.20 0.00 855.45 0 864 avg-cpu: %user %nice %system %iowait %steal %idle 57.22 0.00 5.69 0.00 0.00 37.09 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 33.00 0.00 432.00 0 432 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 33.00 0.00 432.00 0 432 avg-cpu: %user %nice %system %iowait %steal %idle 56.03 0.00 7.93 0.00 0.00 36.04 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 41.00 0.00 560.00 0 560 sda1 0.00 0.00 0.00 0 0 sda2 2.00 0.00 88.00 0 88 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 39.00 0.00 472.00 0 472 avg-cpu: %user %nice %system %iowait %steal %idle 55.78 0.00 5.13 0.00 0.00 39.09 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 29.00 0.00 392.00 0 392 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 29.00 0.00 392.00 0 392 avg-cpu: %user %nice %system %iowait %steal %idle 53.68 0.00 8.30 0.06 0.00 37.95 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 78.00 0.00 4280.00 0 4280 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 78.00 0.00 4280.00 0 4280

  Read the article

• Credentials can not be delegated - Alfresco Share

  - by leftcase

  I've hit a brick wall configuring Alfresco 4.0.d on Redhat 6. I'm using Kerberos authentication, it seems to be working normally, and single sign on is working on the main alfresco app itself. I've been through the configuration steps to get the share app working, but try as I may, I keep getting this error in catalina.out each time a browser accesses http://server:8080/share along with a 'Windows Security' password box. WARN [site.servlet.KerberosSessionSetupPrivilegedAction] credentials can not be delegated! Here's what I've done so far: Using AD users and computers, selected the alfrescohttp account, and selected 'trust this user for delegation to any service (Kerberos only). Copied /opt/alfresco-4.0.d/tomcat/shared/classes/alfresco/web-extension/share-config-custom.xml.sample to share-config-custom.xml and edited like this: <config evaluator="string-compare" condition="Kerberos" replace="true"> <kerberos> <password>*****</password> <realm>MYDOMAIN.CO.UK</realm> <endpoint-spn>HTTP/[email protected]</endpoint-spn> <config-entry>ShareHTTP</config-entry> </kerberos> </config> <config evaluator="string-compare" condition="Remote"> <remote> <keystore> <path>alfresco/web-extension/alfresco-system.p12</path> <type>pkcs12</type> <password>alfresco-system</password> </keystore> <connector> <id>alfrescoCookie</id> <name>Alfresco Connector</name> <description>Connects to an Alfresco instance using cookie-based authentication</description> <class>org.springframework.extensions.webscripts.connector.AlfrescoConnector</class> </connector> <endpoint> <id>alfresco</id> <name>Alfresco - user access</name> <description>Access to Alfresco Repository WebScripts that require user authentication</description> <connector-id>alfrescoCookie</connector-id> <endpoint-url>http://localhost:8080/alfresco/wcs</endpoint-url> <identity>user</identity> <external-auth>true</external-auth> </endpoint> </remote> </config> Setup the /etc/krb5.conf file like this: [logging] default = FILE:/var/log/krb5libs.log kdc = FILE:/var/log/krb5kdc.log admin_server = FILE:/var/log/kadmind.log [libdefaults] default_realm = MYDOMAIN.CO.UK default_tkt_enctypes = rc4-hmac default_tgs_enctypes = rc4-hmac forwardable = true proxiable = true [realms] MYDOMAIN.CO.UK = { kdc = mydc.mydomain.co.uk admin_server = mydc.mydomain.co.uk } [domain_realm] .mydc.mydomain.co.uk = MYDOMAIN.CO.UK mydc.mydomain.co.uk = MYDOMAIN.CO.UK /opt/alfresco-4.0.d/java/jre/lib/security/java.login.config is configured like this: Alfresco { com.sun.security.auth.module.Krb5LoginModule sufficient; }; AlfrescoCIFS { com.sun.security.auth.module.Krb5LoginModule required storeKey=true useKeyTab=true keyTab="/etc/alfrescocifs.keytab" principal="cifs/server.mydomain.co.uk"; }; AlfrescoHTTP { com.sun.security.auth.module.Krb5LoginModule required storeKey=true useKeyTab=true keyTab="/etc/alfrescohttp.keytab" principal="HTTP/server.mydomain.co.uk"; }; com.sun.net.ssl.client { com.sun.security.auth.module.Krb5LoginModule sufficient; }; other { com.sun.security.auth.module.Krb5LoginModule sufficient; }; ShareHTTP { com.sun.security.auth.module.Krb5LoginModule required storeKey=true useKeyTab=true keyTab="/etc/alfrescohttp.keytab" principal="HTTP/server.mydomain.co.uk"; }; And finally, the following settings in alfresco-global.conf authentication.chain=kerberos1:kerberos,alfrescoNtlm1:alfrescoNtlm kerberos.authentication.real=MYDOMAIN.CO.UK kerberos.authentication.user.configEntryName=Alfresco kerberos.authentication.cifs.configEntryName=AlfrescoCIFS kerberos.authentication.http.configEntryName=AlfrescoHTTP kerberos.authentication.cifs.password=****** kerberos.authentication.http.password=***** kerberos.authentication.defaultAdministratorUserNames=administrator ntlm.authentication.sso.enabled=true As I say, I've hit a brick wall with this and I'd really appreciate any help you can give me! This question is also posted on the Alfresco forum, but I wondered if any folk here on serverfault have come across similar implementation challenges?

  Read the article

• SOAP call with query on result (SSRS, Sharepoint)

  - by Erik404

  Hi! I created a report in VS using a shared data source which is connected to a sharepoint list. In the report I created a dataset with a SOAP call to the data source so I get the result from the sharepoint list in a table. this is the soap call <Query> <SoapAction>http://schemas.microsoft.com/sharepoint/soap/GetListItems</SoapAction> <Method Namespace="http://schemas.microsoft.com/sharepoint/soap/" Name="GetListItems"> <Parameters> <Parameter Name="listName"> <DefaultValue>{BD8D39B7-FA0B-491D-AC6F-EC9B0978E0CE}</DefaultValue> </Parameter> <Parameter Name="viewName"> <DefaultValue>{E2168426-804F-4836-9BE4-DC5F8D08A54F}</DefaultValue> </Parameter> <Parameter Name="rowLimit"> <DefaultValue>9999</DefaultValue> </Parameter> </Parameters> </Method> <ElementPath IgnoreNamespaces="True">*</ElementPath> </Query> THis works fine, I have a result which I can show in a report, but I want to have the ability to select a parameter to filter the result on. I have created a parameter and when I preview the Report I see the dropdownbox which I can use to make a selection from the Title field, when I do this it still shows the first record, obviously it doens't work yet (DUH!) because I need to create a query somewhere, But! I have no idea where, I tried to include <Where> <Eq> <FieldRef Name="ows_Title" /> <Value Type="Text">testValue</Value> </Eq> </Where> in the the soap request but it didn't worked... I've searched teh intarwebz but couldn't find any simliar problems... kinda stuck now...any thoughts on this? EDIT Here's the query I used according to the blogpost Alex Angas linked. <Query> <SoapAction>http://schemas.microsoft.com/sharepoint/soap/GetListItems</SoapAction> <Method Namespace="http://schemas.microsoft.com/sharepoint/soap/" Name="GetListItems"> <queryOptions></queryOptions> <query><Query> <Where> <Eq> <FieldRef Name="ows_Title"/> <Value Type="Text">someValue</Value> </Eq> </Where> </Query></query> <Parameters> <Parameter Name="listName"> <DefaultValue>{BD8D39B7-FA0B-491D-AC6F-EC9B0978E0CE}</DefaultValue> </Parameter> <Parameter Name="viewName"> <DefaultValue>{E2168426-804F-4836-9BE4-DC5F8D08A54F}</DefaultValue> </Parameter> <Parameter Name="rowLimit"> <DefaultValue>9999</DefaultValue> </Parameter> </Parameters> </Method> <ElementPath IgnoreNamespaces="True">*</ElementPath> </Query> I tried to put the new query statement in every possible way in the existing, but it doesn't work at all, I do not get an error though so the code is valid, but I still get an unfiltered list as return... pulling my hair out here!

  Read the article

• Strategy for using snapshots to back up Ubuntu Linux server?

  - by MountainX

  I need some backup advice for my home file server. Here are the mount points, volume groups, logical volumes and used/total space of all the volumes on my Ubuntu 8.10 home file server. / vgA/lvRoot [7.5G/50G] /tmp vgB/lvTmp [195M/30G] /var vgB/lvVar [780M/30G] swap vgB/lvSwap [16.00 GB] /media1 vgC/lvMedia1 [400G/975G] /media2 vgC/lvMedia2 [75G/295G] /boot partition (no volume group) [95M/200M] /video partition (no volume group) [450G/950G] /backups vgD/lvBackupTarget [800G/925G] /home vgE/lvHome [85G/200G] I have just added a 2.0 TB external USB drive that I would like to use to backup everything. (It will be a close fit to get it all on one 2.0 TB drive. I actually have a 2nd external USB drive if needed.) I'd like to backup "/", var, /media1, media2 and /home. I'll deal with /boot and /video separately since they are not logical volumes. For all the logical volumes I'm anticipating taking snapshots and then copying those snapshots to the 2.0 TB external USB drive. I have never done a task like that before. If I do that, I could use the tutorial I found here: http://www.howtoforge.com/linux_lvm_snapshots My questions are: What is the best overall strategy? Is it LVM snapshots, as I'm assuming? How should I prepare, subdivide and mount the 2.0 TB external USB drive? 2.a. Should I create one or more regular partitions or should I create a physical volume with one or more logical volumes? 2.b. Would it be advisable to extactly mirror the source pv/lv layout on the external drive, and if so, is this a good strategy? What's the best way to get the snapshots onto the external drive? dd? Even though this is a strategy question, feedback with actual commands is appreciated. I need step-by-step cookbook-style help because I don't do much server admin work. (Background: This is a home file server that I have rarely had to touch in about 2 years. It has done its job without much intervention. The really old PC that I used to back everything up recently failed, so I'm replacing that with the external USB drive(s) and I'd like to upgrade my backup strategy at the same time. Previously, I just copied stuff from /backups over to the other computer and that would not have made things very easy in a real restore situation. The /backups mount point contains backup copies of "most" of the important data on a file by file basis, but it does not contain copies of /boot, etc. BTW, the actual internal HDD that holds /backups is separate from the other storage devices.) EDIT: I'll propose a strategy... The idea came from a comment here: LVM mirroring VS RAID1 "LVM mirrors are for replication of a logical volume to a different physical volume. It's essentially meant to "move the data to a different disk". The mirror is then broken..." That would fit my requirements well. Here is an ideal situation: establish the LV mirror on the external drive break the link with the mirror create a (persistent) snapshot on the mirror after a week, resync the mirror with the original source and update the mirror break the link and create another snapshot on the mirror. Obviously, the mirror will be like a weekly full backup. And the snapshots on the mirror will represent earlier points in time. If this would work and if it would be time efficient, it would give a nice full & differential type backup on the external drive based on LVM. I have not heard of a strategy like this before. Will it work? Could it be scripted? Thoughts? EDIT 2: Creating Portable DiskSafes With LoopbackFS And LVM Snapshots This article seems intriguing: http://www.howtoforge.com/creating-portable-disksafes-with-loopbackfs-and-lvm-snapshots Unfortunately, I don't understand exactly how to map those ideas to the strategy I'm proposing above. I'm going to ask this last bit as a separate question. I will leave my original question in place because I still desire feedback on the overall best strategy. At this moment I'm assuming it is LVM mirroring in the style of "Creating Portable DiskSafes with LVM Snapshots" but that might be wrong.

  Read the article

• Curl Certificate Error when Using RVM to install Ruby 1.9.2

  - by Will Dennis

  RVM is running into a certificate error when trying to download ruby 1.9.2. It looks like curl is having a certificate issue but I am not sure how to bypass it. NAy help would be great. Thanks so much, I have included the exact error info below. $ rvm install 1.9.2 Installing Ruby from source to: /Users/willdennis/.rvm/rubies/ruby-1.9.2-p180, this may take a while depending on your cpu(s)... ruby-1.9.2-p180 - #fetching ERROR: Error running 'bunzip2 '/Users/willdennis/.rvm/archives/ruby-1.9.2-p180.tar.bz2'', please read /Users/willdennis/.rvm/log/ruby-1.9.2-p180/extract.log ruby-1.9.2-p180 - #extracting ruby-1.9.2-p180 to /Users/willdennis/.rvm/src/ruby-1.9.2-p180 ruby-1.9.2-p180 - #extracted to /Users/willdennis/.rvm/src/ruby-1.9.2-p180 Fetching yaml-0.1.3.tar.gz to /Users/willdennis/.rvm/archives curl: (60) SSL certificate problem, verify that the CA cert is OK. Details: error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate verify failed More details here: http://curl.haxx.se/docs/sslcerts.html curl performs SSL certificate verification by default, using a "bundle" of Certificate Authority (CA) public keys (CA certs). The default bundle is named curl-ca-bundle.crt; you can specify an alternate file using the --cacert option. If this HTTPS server uses a certificate signed by a CA represented in the bundle, the certificate verification probably failed due to a problem with the certificate (it might be expired, or the name might not match the domain name in the URL). If you'd like to turn off curl's verification of the certificate, use the -k (or --insecure) option. ERROR: There was an error, please check /Users/willdennis/.rvm/log/ruby-1.9.2-p180/*.log. Next we'll try to fetch via http. Trying http:// URL instead. curl: (60) SSL certificate problem, verify that the CA cert is OK. Details: error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate verify failed More details here: http://curl.haxx.se/docs/sslcerts.html curl performs SSL certificate verification by default, using a "bundle" of Certificate Authority (CA) public keys (CA certs). The default bundle is named curl-ca-bundle.crt; you can specify an alternate file using the --cacert option. If this HTTPS server uses a certificate signed by a CA represented in the bundle, the certificate verification probably failed due to a problem with the certificate (it might be expired, or the name might not match the domain name in the URL). If you'd like to turn off curl's verification of the certificate, use the -k (or --insecure) option. ERROR: There was an error, please check /Users/willdennis/.rvm/log/ruby-1.9.2-p180/*.log Extracting yaml-0.1.3.tar.gz to /Users/willdennis/.rvm/src ERROR: Error running 'tar zxf /Users/willdennis/.rvm/archives/yaml-0.1.3.tar.gz -C /Users/willdennis/.rvm/src --no-same-owner', please read /Users/willdennis/.rvm/log/ruby-1.9.2-p180/yaml/extract.log /Users/willdennis/.rvm/scripts/functions/packages: line 55: cd: /Users/willdennis/.rvm/src/yaml-0.1.3: No such file or directory Configuring yaml in /Users/willdennis/.rvm/src/yaml-0.1.3. ERROR: Error running ' ./configure --prefix="/Users/willdennis/.rvm/usr" ', please read /Users/willdennis/.rvm/log/ruby-1.9.2-p180/yaml/configure.log Compiling yaml in /Users/willdennis/.rvm/src/yaml-0.1.3. ERROR: Error running '/usr/bin/make ', please read /Users/willdennis/.rvm/log/ruby-1.9.2-p180/yaml/make.log Installing yaml to /Users/willdennis/.rvm/usr ERROR: Error running '/usr/bin/make install', please read /Users/willdennis/.rvm/log/ruby-1.9.2-p180/yaml/make.install.log ruby-1.9.2-p180 - #configuring ERROR: Error running ' ./configure --prefix=/Users/willdennis/.rvm/rubies/ruby-1.9.2-p180 --enable-shared --disable-install-doc --with-libyaml-dir=/Users/willdennis/.rvm/usr ', please read /Users/willdennis/.rvm/log/ruby-1.9.2-p180/configure.log ERROR: There has been an error while running configure. Halting the installation. Will

  Read the article

• How to convert html textfield/area data to server-side txt file? [closed]

  - by olijake

  How can I make a script that will convert the text/data in a html textfield/textarea and send it to the server, which then saves it as a .txt file for storage? NOTE: I am hosting a website(for testing purposes) using Apache 2.2 on a Windows 7 machine. I downloaded PHP version 5.4.7, but have not yet installed on my server yet (not sure if I will need it, but also not sure how to install it). 1st problem: Saving text to server Html page/section with title textfield, text textarea, and submit button. You would enter a title, the text/notes you need in the textfield, then press the submit button to have it store the text in the textarea, as a .txt file on the server called .txt. 2nd problem: Opening text from server Html with list of all txt files OR textfield for entering in title, then submit button to send the title of the requested .txt file to the server, which would then load it up on the page. Here is what I have so far: (let me know if there is something that I should change or if something just isn't correct in the index.html code I have right now.) <!DOCTYPE HTML> <html> <head> <title>Insert Title</title> <meta http-equiv="Content-Type" content="Text/HTML; charset=UTF-8"/> </head> <body> <form method="post" action="save.INSERT_FILETYPE" name="textfile" enctype="multipart/form-data"> <input type="text" name="title"><br/> <textarea rows="20" cols="100" id="text" name="text"></textarea><br/> <input type="submit" name="submit" value="Submit Text to Server"> </form><br/> <hr style="width: 100%; height: 4px;"><br/> <form method="post" action="open.INSERT_FILETYPE" name="textfile" enctype="multipart/form-data"> <input type="text" name="title"><br/> <input type="submit" name="submit" value="Submit Txt File Request"> </form><br/> <div>Opened text file displays here or goes on another page</div> </body> </html> I plan on using a server side language/script, but ANYTHING that gets the job done is fine. I already tried looking into using some ASP/jScript/PHP, but have had some trouble implementing it into my server. (ie: getting the modules loaded and telling the server what file types to parse.) I know this may be an extremely easy fix, but then in that case, hopefully you wouldn't mind helping me out a little :). If it turns out that this is MUCH more complicated than I expect, then feel free to let me know that, so I don't waste me time running in circles. I appreciate any help/assistance that you can provide, Thanks, Jake EDIT: Wrong Apache version. In response to the comments/closing of this thread: My question: "How exactly do I install the PHP module on the apache server? and is this even possible? and is this even recommended?" ^ In case I wasn't clear enough already To Clarify: I understand the basics of PHP, I just have trouble with INSTALLING PHP on the apache server. (I have used PHP before, but never successfully on apache (so far...)) For my script I wrote something similar to this already (using fopen() and a few other commands): <?php fopen("notes.txt", "r"); file_put_contents("notes.txt",teststring1); ?> I have used javascript for this task before also (although I prefer using PHP and server-side languages): <script language="javascript"> function WriteToFile(){ var fso = new ActiveXObject("Scripting.FileSystemObject"); var s = fso.CreateTextFile("C:\\NewFile.txt", true); var text=document.getElementById("TextArea1").innerText; s.WriteLine(text); s.WriteLine('***********************'); s.Close(); } </script>

  Read the article

• Installing nGinX Reverse Proxy on CentOS 5

  - by heavymark

  I'm trying to install nGinX as a reverse proxy on CentOS 5 with apache. The instructions to do this are here: http://wiki.mediatemple.net/w/(dv):Configure_nginx_as_reverse_proxy_web_server Note- in the instructions, for the url to get nginx I'm using the following: http://nginx.org/download/nginx-1.0.10.tar.gz Now here is my problem. After installing the required packages and running .configure I get the following: checking for OS + Linux 2.6.18-028stab094.3 x86_64 checking for C compiler ... found + using GNU C compiler + gcc version: 4.1.2 20080704 (Red Hat 4.1.2-51) checking for gcc -pipe switch ... found checking for gcc builtin atomic operations ... found checking for C99 variadic macros ... found checking for gcc variadic macros ... found checking for unistd.h ... found checking for inttypes.h ... found checking for limits.h ... found checking for sys/filio.h ... not found checking for sys/param.h ... found checking for sys/mount.h ... found checking for sys/statvfs.h ... found checking for crypt.h ... found checking for Linux specific features checking for epoll ... found checking for sendfile() ... found checking for sendfile64() ... found checking for sys/prctl.h ... found checking for prctl(PR_SET_DUMPABLE) ... found checking for sched_setaffinity() ... found checking for crypt_r() ... found checking for sys/vfs.h ... found checking for nobody group ... found checking for poll() ... found checking for /dev/poll ... not found checking for kqueue ... not found checking for crypt() ... not found checking for crypt() in libcrypt ... found checking for F_READAHEAD ... not found checking for posix_fadvise() ... found checking for O_DIRECT ... found checking for F_NOCACHE ... not found checking for directio() ... not found checking for statfs() ... found checking for statvfs() ... found checking for dlopen() ... not found checking for dlopen() in libdl ... found checking for sched_yield() ... found checking for SO_SETFIB ... not found checking for SO_ACCEPTFILTER ... not found checking for TCP_DEFER_ACCEPT ... found checking for accept4() ... not found checking for int size ... 4 bytes checking for long size ... 8 bytes checking for long long size ... 8 bytes checking for void * size ... 8 bytes checking for uint64_t ... found checking for sig_atomic_t ... found checking for sig_atomic_t size ... 4 bytes checking for socklen_t ... found checking for in_addr_t ... found checking for in_port_t ... found checking for rlim_t ... found checking for uintptr_t ... uintptr_t found checking for system endianess ... little endianess checking for size_t size ... 8 bytes checking for off_t size ... 8 bytes checking for time_t size ... 8 bytes checking for setproctitle() ... not found checking for pread() ... found checking for pwrite() ... found checking for sys_nerr ... found checking for localtime_r() ... found checking for posix_memalign() ... found checking for memalign() ... found checking for mmap(MAP_ANON|MAP_SHARED) ... found checking for mmap("/dev/zero", MAP_SHARED) ... found checking for System V shared memory ... found checking for POSIX semaphores ... not found checking for POSIX semaphores in libpthread ... found checking for struct msghdr.msg_control ... found checking for ioctl(FIONBIO) ... found checking for struct tm.tm_gmtoff ... found checking for struct dirent.d_namlen ... not found checking for struct dirent.d_type ... found checking for PCRE library ... found checking for system md library ... not found checking for system md5 library ... not found checking for OpenSSL md5 crypto library ... found checking for sha1 in system md library ... not found checking for OpenSSL sha1 crypto library ... found checking for zlib library ... found creating objs/Makefile Configuration summary + using system PCRE library + OpenSSL library is not used + md5: using system crypto library + sha1: using system crypto library + using system zlib library nginx path prefix: "/usr/local/nginx" nginx binary file: "/usr/local/nginx/sbin/nginx" nginx configuration prefix: "/usr/local/nginx/conf" nginx configuration file: "/usr/local/nginx/conf/nginx.conf" nginx pid file: "/usr/local/nginx/logs/nginx.pid" nginx error log file: "/usr/local/nginx/logs/error.log" nginx http access log file: "/usr/local/nginx/logs/access.log" nginx http client request body temporary files: "client_body_temp" nginx http proxy temporary files: "proxy_temp" nginx http fastcgi temporary files: "fastcgi_temp" nginx http uwsgi temporary files: "uwsgi_temp" nginx http scgi temporary files: "scgi_temp" It says if you get errors to stop and make sure packages are installed. I didn't get errors but as you can see I got several "not founds". Are those considered errors? If so how do I resolve that. And as noted in the link, I cannot install through yum, because it wont work with plesk then. Thanks!

  Read the article

• ASP.net roles and Projects

  - by Zyphrax

  EDIT - Rewrote my original question to give a bit more information Background info At my work I'm working on a ASP.Net web application for our customers. In our implementation we use technologies like Forms authentication with MembershipProviders and RoleProviders. All went well until I ran into some difficulties with configuring the roles, because the roles aren't system-wide, but related to the customer accounts and projects. I can't name our exact setup/formula, because I think our company wouldn't approve that... What's a customer / project? Our company provides management information for our customers on a yearly (or other interval) basis. In our systems a customer/contract consists of: one Account: information about the Company per Account, one or more Products: the bundle of management information we'll provide per Product, one or more Measurements: a period of time, in which we gather and report the data Extranet site setup Eventually we want all customers to be able to access their management information with our online system. The extranet consists of two sites: Company site: provides an overview of Account information and the Products Measurement site: after selecting a Measurement, detailed information on that period of time The measurement site is the most interesting part of the extranet. We will create submodules for new overviews, reports, managing and maintaining resources that are important for the research. Our Visual Studio solution consists of a number of projects. One web application named Portal for the basis. The sites and modules are virtual directories within that application (makes it easier to share MasterPages among things). What kind of roles? The following users (read: roles) will be using the system: Admins: development users :) (not customer related, full access) Employees: employees of our company (not customer related, full access) Customer SuperUser: top level managers (full access to their account/measurement) Customer ContactPerson: primary contact (full access to their measurement(s)) Customer Manager: a department manager (limited access, specific data of a measurement) What about ASP.Net users? The system will have many ASP.Net users, let's focus on the customer users: Users are not shared between Accounts SuperUser X automatically has access to all (and new) measurements User Y could be Primary contact for Measurement 1, but have no role for Measurement 2 User Y could be Primary contact for Measurement 1, but have a Manager role for Measurement 2 The department managers are many individual users (per Measurement), if Manager Z had a login for Measurement 1, we would like to use that login again if he participates in Measurement 2. URL structure These are typical urls in our application: http://host/login - the login screen http://host/project - the account/product overview screen (measurement selection) http://host/project/1000 - measurement (id:1000) details http://host/project/1000/planning - planning overview (for primary contact/superuser) http://host/project/1000/reports - report downloads (manager department X can only access report X) We will also create a document url, where you can request a specific document by it's GUID. The system will have to check if the user has rights to the document. The document is related to a Measurement, the User or specific roles have specific rights to the document. What's the problem? (finally ;)) Roles aren't enough to determine what a user is allowed to see/access/download a specific item. It's not enough to say that a certain navigation item is accessible to Managers. When the user requests Measurement 1000, we have to check that the user not only has a Manager role, but a Manager role for Measurement 1000. Summarized: How can we limit users to their accounts/measurements? (remember superusers see all measurements, some managers only specific measurements) How can we apply roles at a product/measurement level? (user X could be primarycontact for measurement 1, but just a manager for measurement 2) How can we limit manager access to the reports screen and only to their department's reports? All with the magic of asp.net classes, perhaps with a custom roleprovider implementation. Similar Stackoverflow question/problem http://stackoverflow.com/questions/1367483/asp-net-how-to-manage-users-with-different-types-of-roles

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

• How do I load an image from sd card into coverview

  - by Jolene

  I am doing an application which consists of a cover flow. Currently I am trying to make the cover flow images be obtained from the sd card. But I am not exactly sure how should I display the image. this is the image adapter: public class ImageAdapter extends BaseAdapter { int mGalleryItemBackground; private Context mContext; private FileInputStream fis; private Integer[] mImageIds = { //Instead of using r.drawable, i need to load the images from my sd card instead R.drawable.futsing, R.drawable.futsing2 }; private ImageView[] mImages; public ImageAdapter(Context c) { mContext = c; mImages = new ImageView[mImageIds.length]; } public int getCount() { return mImageIds.length; } public Object getItem(int position) { return position; } public long getItemId(int position) { return position; } @TargetApi(8) public View getView(int position, View convertView, ViewGroup parent) { int screenSize = getResources().getConfiguration().screenLayout & Configuration.SCREENLAYOUT_SIZE_MASK; ImageView i = new ImageView(mContext); i.setImageResource(mImageIds[position]); switch(screenSize) { case Configuration.SCREENLAYOUT_SIZE_XLARGE: //Toast.makeText(this, "Small screen",Toast.LENGTH_LONG).show(); Display display4 = ((WindowManager) context.getSystemService(Context.WINDOW_SERVICE)).getDefaultDisplay(); int rotation4 = display4.getRotation(); Log.d("XLarge:",String.valueOf(rotation4)); /** LANDSCAPE **/ if(rotation4 == 0 || rotation4 == 2) { i.setLayoutParams(new CoverFlow.LayoutParams(300, 300)); i.setScaleType(ImageView.ScaleType.CENTER_INSIDE); BitmapDrawable drawable = (BitmapDrawable) i.getDrawable(); drawable.setAntiAlias(true); return i; } /** PORTRAIT **/ else if (rotation4 == 1 || rotation4 == 3) { i.setLayoutParams(new CoverFlow.LayoutParams(650, 650)); i.setScaleType(ImageView.ScaleType.CENTER_INSIDE); BitmapDrawable drawable = (BitmapDrawable) i.getDrawable(); drawable.setAntiAlias(true); return i; } break; default: } return null; } /** Returns the size (0.0f to 1.0f) of the views * depending on the 'offset' to the center. */ public float getScale(boolean focused, int offset) { /* Formula: 1 / (2 ^ offset) */ return Math.max(0, 1.0f / (float)Math.pow(2, Math.abs(offset))); } } and this is how i download and save the file. I need to use the image saved and upload it into my coverflow // IF METHOD TO DOWNLOAD IMAGE void downloadFile() { new Thread(new Runnable(){ // RUN IN BACKGROUND THREAD TO AVOID FREEZING OF UI public void run(){ Bitmap bmImg; URL myFileUrl = null; try { //for (int i = 0; i < urlList.size(); i ++) //{ //url = urlList.get(i); myFileUrl = new URL("http://static.adzerk.net/Advertisers/d18eea9d28f3490b8dcbfa9e38f8336e.jpg"); // RETRIEVE IMAGE URL //} } catch (MalformedURLException e) { e.printStackTrace(); } try { HttpURLConnection conn = (HttpURLConnection) myFileUrl.openConnection(); conn.setDoInput(true); conn.connect(); InputStream in = conn.getInputStream(); Log.i("im connected", "Download"); bmImg = BitmapFactory.decodeStream(in); saveFile(bmImg); } catch (IOException e) { e.printStackTrace(); }} }).start(); // START THREAD } // SAVE THE IMAGE AS JPG FILE private void saveFile(Bitmap bmImg) { File filename; try { // GET EXTERNAL STORAGE, SAVE FILE THERE File storagePath = new File(Environment.getExternalStorageDirectory(),"Covers"); storagePath.mkdirs(); filename = new File(storagePath + "/image.jpg"); FileOutputStream out = new FileOutputStream(filename); bmImg.compress(Bitmap.CompressFormat.JPEG, 90, out); out.flush(); out.close(); MediaStore.Images.Media.insertImage(getContentResolver(),filename.getAbsolutePath(), filename.getName(), filename.getName()); // ONCE THE DOWNLOAD FINISHES, CLOSE DIALOG Toast.makeText(getApplicationContext(), "Image Saved!", Toast.LENGTH_SHORT).show(); } catch (Exception e) { e.printStackTrace(); } }

  Read the article

• I am getting error when using Attributes in Rcpp and have RcppArmadillo code

  - by howard123

  I am trying to create a package with RcppArmadillo. The code uses the new attributes methodology of Rcpp. The sourceCpp works fine and compiles the code, but when I build a package I get errors when I use RcppArmadillo code. Without the RcppArmadillo code and using regulare C++, I do not get these errors. The C++ code (it is essentially the fastLm sample code) is: // [[Rcpp::depends(RcppArmadillo)]] #include <Rcpp.h> #include <RcppArmadillo.h> using namespace Rcpp; // [[Rcpp::depends(RcppArmadillo)]] #include <RcppArmadillo.h> // [[Rcpp::export]] List fastLm(NumericVector yr, NumericMatrix Xr) { int n = Xr.nrow(), k = Xr.ncol(); arma::mat X(Xr.begin(), n, k, false); arma::colvec y(yr.begin(), yr.size(), false); arma::colvec coef = arma::solve(X, y); arma::colvec resid = y - X*coef; double sig2 = arma::as_scalar(arma::trans(resid)*resid/(n-k)); arma::colvec stderrest = arma::sqrt( sig2 * arma::diagvec( arma::inv(arma::trans(X)*X)) ); return List::create(Named("coefficients") = coef, Named("stderr") = stderrest); } Here is the compilation error, after I execute "R Rcpp::compileAttributes() * Updated src/RcppExports.cpp == Rcmd.exe INSTALL --no-multiarch NewPackage * installing to library 'C:/Users/Howard/Documents/R/win-library/2.15' * installing *source* package 'NewPackage' ... ** libs g++ -m64 -I"C:/R/R-2-15-2/include" -DNDEBUG -I"C:/Users/Howard/Documents/R/win-library/2.15/Rcpp/include" -I"C:/Users/Howard/Documents/R/win-library/2.15/RcppArmadillo/include" -I"d:/RCompile/CRANpkg/extralibs64/local/include" -O2 -Wall -mtune=core2 -c RcppExports.cpp -o RcppExports.o g++ -m64 -I"C:/R/R-2-15-2/include" -DNDEBUG -I"C:/Users/Howard/Documents/R/win-library/2.15/Rcpp/include" -I"C:/Users/Howard/Documents/R/win-library/2.15/RcppArmadillo/include" -I"d:/RCompile/CRANpkg/extralibs64/local/include" -O2 -Wall -mtune=core2 -c test_arma3.cpp -o test_arma3.o g++ -m64 -shared -s -static-libgcc -o NewPackage.dll tmp.def RcppExports.o test_arma3.o C:/Users/Howard/Documents/R/win-library/2.15/Rcpp/lib/x64/libRcpp.a -Ld:/RCompile/CRANpkg/extralibs64/local/lib/x64 -Ld:/RCompile/CRANpkg/extralibs64/local/lib -LC:/R/R-2-15-2/bin/x64 -lR test_arma3.o:test_arma3.cpp:(.text+0xae4): undefined reference to `dgemm_' test_arma3.o:test_arma3.cpp:(.text+0x19db): undefined reference to `dgemm_' test_arma3.o:test_arma3.cpp:(.text+0x1b0c): undefined reference to `dgemv_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma6auxlib8solve_odIdNS_3MatIdEEEEbRNS2_IT_EES6_RKNS_4BaseIS4_T0_EE[_ZN4arma6auxlib8solve_odIdNS_3MatIdEEEEbRNS2_IT_EES6_RKNS_4BaseIS4_T0_EE]+0x702): undefined reference to `dgels_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma6auxlib8solve_udIdNS_3MatIdEEEEbRNS2_IT_EES6_RKNS_4BaseIS4_T0_EE[_ZN4arma6auxlib8solve_udIdNS_3MatIdEEEEbRNS2_IT_EES6_RKNS_4BaseIS4_T0_EE]+0x51c): undefined reference to `dgels_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma6auxlib10det_lapackIdEET_RKNS_3MatIS2_EEb[_ZN4arma6auxlib10det_lapackIdEET_RKNS_3MatIS2_EEb]+0x14b): undefined reference to `dgetrf_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma6auxlib5solveIdNS_3MatIdEEEEbRNS2_IT_EES6_RKNS_4BaseIS4_T0_EEb[_ZN4arma6auxlib5solveIdNS_3MatIdEEEEbRNS2_IT_EES6_RKNS_4BaseIS4_T0_EEb]+0x375): undefined reference to `dgesv_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma4gemvILb1ELb0ELb0EE15apply_blas_typeIdEEvPT_RKNS_3MatIS3_EEPKS3_S3_S3_[_ZN4arma4gemvILb1ELb0ELb0EE15apply_blas_typeIdEEvPT_RKNS_3MatIS3_EEPKS3_S3_S3_]+0x17d): undefined reference to `dgemv_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma27glue_times_redirect2_helperILb1EE5applyINS_2OpINS_3MatIdEENS_9op_htransEEES5_EEvRNS4_INT_9elem_typeEEERKNS_4GlueIS8_T0_NS_10glue_timesEEE[_ZN4arma27glue_times_redirect2_helperILb1EE5applyINS_2OpINS_3MatIdEENS_9op_htransEEES5_EEvRNS4_INT_9elem_typeEEERKNS_4GlueIS8_T0_NS_10glue_timesEEE]+0x37a): undefined reference to `dgemm_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE[_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE]+0x2c1): undefined reference to `dgetrf_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE[_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE]+0x322): undefined reference to `dgetri_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE[_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE]+0x398): undefined reference to `dgetri_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE[_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE]+0x775): undefined reference to `dgetrf_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE[_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE]+0x7d6): undefined reference to `dgetri_' test_arma3.o:test_arma3.cpp:(.text$_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE[_ZN4arma10op_diagvec5applyINS_2OpINS_4GlueINS2_INS_3MatIdEENS_9op_htransEEES5_NS_10glue_timesEEENS_6op_invEEEEEvRNS4_INT_9elem_typeEEERKNS2_ISC_S0_EE]+0x892): undefined reference to `dgetri_' collect2: ld returned 1 exit status ERROR: compilation failed for package 'NewPackage' * removing 'C:/Users/Howard/Documents/R/win-library/2.15/NewPackage' * restoring previous 'C:/Users/Howard/Documents/R/win-library/2.15/NewPackage' Exited with status 1.

  Read the article

• Asp.net mvc, view with multiple updatable parts - how?

  - by DerDres

  I have started doing asp.net mvc programming and like it more everyday. Most of the examples I have seen use separate views for viewing and editing details of a specific entity. E.g. - table of music albums linking to separate 'detail' and 'update' views [Action] | Title | Artist detail, update | Uuuh Baby | Barry White detail, update | Mr Mojo | Barry White With mvc how can I achieve a design where the R and the U (CRUD) are represented in a single view, and furthermore where the user can edit separate parts of the view, thus limiting the amount of data the user can edit before saving? Example mockup - editing album detials: I have achieved such a design with ajax calls, but Im curious how to do this without ajax. Parts of my own take on this can be seen below. I use a flag (enum EditCode) indicating which part of the view, if any, that has to render a form. Is such a design in accordance with the framework, could it be done more elegantly? AlbumController public class AlbumController : Controller { public ActionResult Index() { var albumDetails = from ManageVM in state.AlbumState.ToList() select ManageVM.Value.Detail; return View(albumDetails); } public ActionResult Manage(int albumId, EditCode editCode) { (state.AlbumState[albumId] as ManageVM).EditCode = (EditCode)editCode; ViewData["albumId"] = albumId; return View(state.AlbumState[albumId]); } [HttpGet] public ActionResult Edit(int albumId, EditCode editCode) { return RedirectToAction("Manage", new { albumId = albumId, editCode = editCode }); } // edit album details [HttpPost] public ActionResult EditDetail(int albumId, Detail details) { (state.AlbumState[albumId] as ManageVM).Detail = details; return RedirectToAction("Manage", new { albumId = albumId, editCode = EditCode.NoEdit });// zero being standard } // edit album thought [HttpPost] public ActionResult EditThoughts(int albumId, List<Thought> thoughts) { (state.AlbumState[albumId] as ManageVM).Thoughts = thoughts; return RedirectToAction("Manage", new { albumId = albumId, editCode = EditCode.NoEdit });// zero being standard } Flag - EditCode public enum EditCode { NoEdit, Details, Genres, Thoughts } Mangae view <%@ Page Title="" Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage<MvcApplication1.Controllers.ManageVM>" %> <asp:Content ID="Content1" ContentPlaceHolderID="TitleContent" runat="server"> Manage </asp:Content> <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> <h2>Manage</h2> <% if(Model.EditCode == MvcApplication1.Controllers.EditCode.Details) {%> <% Html.RenderPartial("_EditDetails", Model.Detail); %> <% }else{%> <% Html.RenderPartial("_ShowDetails", Model.Detail); %> <% } %> <hr /> <% if(Model.EditCode == MvcApplication1.Controllers.EditCode.Thoughts) {%> <% Html.RenderPartial("_EditThoughts", Model.Thoughts); %> <% }else{%> <% Html.RenderPartial("_ShowThoughts", Model.Thoughts); %> <% } %>

  Read the article

• Linux networking crash: best steps to find out the cause?

  - by Aron Rotteveel

  One of our Linux (CentOS) servers was unreachable last night. The server was not reachable in any way except for the remote console. After logging in with the remote console, it turned out I could not ping any outside hosts either. A simple service network restart solved the issue, but I am still wondering what could have caused this. My log files seem to indicate no error at all (except for the various daemons that need a network connection and failed after the network failure). Are there any additional steps I can take to find out the cause of this problem? EDIT: this just happened again. The server was completely unresponsive until I issued a networking service restart. Any advise is welcome. Could this be caused by a faulty hardware component? As per Madhatters request, here are some excerpts from the log at the time (the network crashed at 20:13): /var/log/messages: Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=100 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:13:34 graviton junglediskserver: Connection to gateway failed: xGatewayTransport - Connection to gateway failed. The first three messages are simple responses to iptables rules I have set up through the LFD firewall. The last message indicates that JungleDisk, which I use for backups can no longer connect to the gateway. Apart from this, there are no interesting messages around this time. EDIT 4 dec: as per Mattdm's request, here is the output of ethtool eth0: (Please not that these are the settings that currently work. If things go wrong again, I will be sure to post this again if necessary. Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Link detected: yes As per Joris' request, here is also the output of route -n: aron@graviton [~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.xx.xx.58 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.42 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.43 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.41 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.46 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.47 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.44 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.45 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.50 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.51 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.48 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.49 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.54 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.52 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.53 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 xx.xx.xx.62 0.0.0.0 UG 0 0 0 eth0 The bottom xx.62 is my gateway. EDIT december 28th: the problem occurred again and I got the chance to compare some of the outputs of the above tests. What I found out is that arp -an returns an incomplete MAC address for my gateway (which is not under my control; the server is in a shared rack): During failure: ? (xx.xx.xx.62) at <incomplete> on eth0 After service network restart: ? (xx.xx.xx.62) at 00:00:0C:9F:F0:30 [ether] on eth0 Is this something I can fix or is it time for me to contact the data centre?

  Read the article

• Mobile App Data Syncronization

  - by Matt Rogish

  Let's say I have a mobile app that uses HTML5 SQLite DB (and/or the HTML5 key-value store). Assets (media files, PDFs, etc.) are stored locally on the mobile device. Luckily enough, the mobile device is a read-only copy of the "centralized" storage, so the mobile device won't have to propagate changes upstream. However, as the server changes assets (creates new ones, modifies existing, deletes old ones) I need to propagate those changes back to the mobile app. Assume that server changes are grouped into changesets (version number n) that contain some information (added element XYZ, deleted id = 45, etc.) and that the mobile device has limited CPU/bandwidth, so most of the processing has to take place on the server. I can think of a couple of methods to do this. All have trade-offs and at this point, I'm unsure which is the right course of action... Method 1: For change set n, store the "diff" of the current n and previous n-1. When a client with version y asks if there have been any changes, send the change sets from version y up to the current version. e.g. added item 334, contents: xxx. Deleted picture 44. Deleted PDF 11. Changed 33. added picture 99. Characteristics: Diffs take up space, although in theory would be kept small. However, all diffs must be kept around indefinitely (should a v1 app have not been updated for a year, must apply v2..v100). High latency devices (mobile apps) will incur a penalty to send lots of small files (assume cannot be zipped or tarr'd up into one file) Very few server CPU resources required, as all it does is send the client a list of files "Dumb" - if I change an item in change set 3, and change it to something else in 4, the client is going to perform both actions, even though #3 is rendered moot by #4. Or, if an asset is added in #4 and removed in #5 - the client will download a file just to delete it later. Method 2: Very similar to method 1 except on the server, do some sort of a diff between the change sets represented by the app version and server version. Package that up and send that single change set to the client. Characteristics: Client-efficient: The client only has to process one file, duplicate or irrelevant changes are stripped out. Server CPU/space intensive. The change sets must be diff'd and then written out to a file that is then sent to the client. Makes diff server scalability an issue. Possibly ways to cache the results and re-use them, but in the wild there's likely to be a lot of different versions so the diff re-use has a limit Diff algorithm is complicated. The change sets must be structured in such a way that an efficient and effective diff can be performed. Method 3: Instead of keeping diffs, write out the entire versioned asset collection to a mobile-database import file. When client requests an update, send the entire database to client and have them update their assets appropriately. Characteristics: Conceptually simple -- easy to develop and deploy Very inefficient as the client database is restored every update. If only one new thing was added, the whole database is refreshed. Server space and CPU efficient. Only the latest version DB needs kept around and the server just throws the file to the client. Others?? Thoughts? Thanks!!

  Read the article

• Python bindings for a vala library

  - by celil

  I am trying to create python bindings to a vala library using the following IBM tutorial as a reference. My initial directory has the following two files: test.vala using GLib; namespace Test { public class Test : Object { public int sum(int x, int y) { return x + y; } } } test.override %% headers #include <Python.h> #include "pygobject.h" #include "test.h" %% modulename test %% import gobject.GObject as PyGObject_Type %% ignore-glob *_get_type %% and try to build the python module source test_wrap.c using the following code build.sh #/usr/bin/env bash valac test.vala -CH test.h python /usr/share/pygobject/2.0/codegen/h2def.py test.h > test.defs pygobject-codegen-2.0 -o test.override -p test test.defs > test_wrap.c However, the last command fails with an error $ ./build.sh Traceback (most recent call last): File "/usr/share/pygobject/2.0/codegen/codegen.py", line 1720, in <module> sys.exit(main(sys.argv)) File "/usr/share/pygobject/2.0/codegen/codegen.py", line 1672, in main o = override.Overrides(arg) File "/usr/share/pygobject/2.0/codegen/override.py", line 52, in __init__ self.handle_file(filename) File "/usr/share/pygobject/2.0/codegen/override.py", line 84, in handle_file self.__parse_override(buf, startline, filename) File "/usr/share/pygobject/2.0/codegen/override.py", line 96, in __parse_override command = words[0] IndexError: list index out of range Is this a bug in pygobject, or is something wrong with my setup? What is the best way to call code written in vala from python? EDIT: Removing the extra line fixed the current problem, but now as I proceed to build the python module, I am facing another problem. Adding the following C file to the existing two in the directory: test_module.c #include <Python.h> void test_register_classes (PyObject *d); extern PyMethodDef test_functions[]; DL_EXPORT(void) inittest(void) { PyObject *m, *d; init_pygobject(); m = Py_InitModule("test", test_functions); d = PyModule_GetDict(m); test_register_classes(d); if (PyErr_Occurred ()) { Py_FatalError ("can't initialise module test"); } } and building with the following script build.sh #/usr/bin/env bash valac test.vala -CH test.h python /usr/share/pygobject/2.0/codegen/h2def.py test.h > test.defs pygobject-codegen-2.0 -o test.override -p test test.defs > test_wrap.c CFLAGS="`pkg-config --cflags pygobject-2.0` -I/usr/include/python2.6/ -I." LDFLAGS="`pkg-config --libs pygobject-2.0`" gcc $CFLAGS -fPIC -c test.c gcc $CFLAGS -fPIC -c test_wrap.c gcc $CFLAGS -fPIC -c test_module.c gcc $LDFLAGS -shared test.o test_wrap.o test_module.o -o test.so python -c 'import test; exit()' results in an error: $ ./build.sh ***INFO*** The coverage of global functions is 100.00% (1/1) ***INFO*** The coverage of methods is 100.00% (1/1) ***INFO*** There are no declared virtual proxies. ***INFO*** There are no declared virtual accessors. ***INFO*** There are no declared interface proxies. Traceback (most recent call last): File "<string>", line 1, in <module> ImportError: ./test.so: undefined symbol: init_pygobject Where is the init_pygobject symbol defined? What have I missed linking to?

  Read the article

• How does one get rid of fishy behavior in Windows?

  - by Tom Wijsman

  After I had boot my computer this morning there suddenly flooded water from the top of the screen, after which some fishes dropped into it. Now I can barely see what I am doing because the water distorts the view. Sometimes the fish follow the cursor so I need to move it away or wait for the fish to mind their own business. This makes it very annoying to use my system. What have I tried? Reboot the system. This caused the water to deplete from the desktop. Upon reboot, the screen was refilled with water and fishes. Attach another monitor. Same problem, fills that monitor as well and gives me extra fish. Clicking the fish. Makes them turn direction. Right clicking the fish. Changes color of the fish, not really useful. I'm locked out of changing the background or screen saver settings. Hence, I had to post the lady below... Safe mode doesn't save me from the fishes. It does give me another background there, but I can't screenshot easily. Other user accounts experience this as well. The Guest account seems to experience more fish than the other accounts. Using HijackThis, OTL Timekeeper List, Syninternal Autoruns, RootKitRevealer, ShellExView and similar tools I can't seem to find any entries that could be it, the Sysinternals tools show everything as verified. I'm suspecting this to be a driver problem. Randomly removing drivers doesn't seem to alleviate the problem. When removing the Graphics Drivers, it makes my screen black. While that could be considered the solution, it's not what I want. Changing the time / date settings does also not seem to affect the fishes. Changing the time a few years in the future, I would have expected the fishes to be dead. But, the same fishes are still there... They simply won't die! Tried to get used to them. They are really bothering me, looks like they require food. I don't know how to give them food, but apparently they get it elsewhere during reboot... Tried to disable my mouse pointer and use the keyboard. This works, they now swim around more randomly. They do put their attention to huge changes on the screen, so I need to type slow. Or otherwise I can't see what I'm tying exactly. Hold my laptop upside down. This seems to affect the water and fishes, but the water stays in the screen. They seem super resistant against water sickness and confusion though... What does the problem look like? What do I need? A way to get rid of these fishes on my screen forever, they are really annoying me a lot and I'm about to crack the screen to see if that makes them escape. Do you have any idea why this problem is occurring? What are my considerations? Buying an USB fish tank could make the fish leave the screen, I am uncertain though whether the fish could leave the screen through the USB cable. Using the FISh (programming language) which seems to provide EXPRESSIVE POWER and EFFICIENT EXECUTION, I can however not find any examples on how to remove fish. What are my Specifications? I'm using a Sony Vaio Fishy laptop. Sony VAIO VGN-Fishy, VAIO. Processor: 1337 MHz, Intel Core 2 Duo, T5432, 1 MB, Intel PM965 Express, 667 MHz. Memory: 1024 MB, DDR2-SDRAM, 667 MHz, 2 x 1024 MB, 4 GB. Disk Drive: 50 GB, Serial ATA, 5400 RPM. Storage Media: Memory Stick™, Memory Stick PRO™. Display: 15.4 ", 1280 x 800 pixels, LCD. Video: GeForce 8400M GT, 128 MB. Optical Drive: DVD±R/RW DL, 24 x, 24 x, 24 x, 6 x, 4 x, 6 x, 4 x, 5 x, 5 x, 8 x, 8 x, 8 x, 8 x, 6 x, 6 x, 24 x, 24 x, 24 x, 16 x. Camera: 1.3 MP, 30 fps. Networking: 2.0+EDR. Keyboard: Touchpad, AZERTY. Operating System/Software: Windows Vista Home Premium. Security: Kensington. Weight & Dimensions: 98.8 oz (2800 g), 14 " (355.8 mm), 10 " (254.4 mm), 0.98 " (24.9 mm). Other features: 100 BASE-TX/10 BASE-T, 802.11a/b/g/n/Draft n, V92/V.90, fishes. Plz! Help me...

  Read the article

• MySQL 5.1.49 freezing every two days

  - by maximus

  Hi all, our mysql system is "freezing" every two days. By "freezing" i mean the following: it doesn't respond to ping we can't login with SSH we don't get any answer from MySQL there is no entry in the error logs! neither from linux neither from MySQL. we have already changed to a completely new hardware, we have the same problem, so it's definitely not a hardware problem. we do not have any other software installed except a firewall (iptables rule) we can restart the server from another server using rsyslog (www.rsyslog.com)(software reset) Could someone help me, by giving me some pointers what could i do to figure out the problem? I have included every detail about our settings. Thank you in advance for your help. Max. Our system parameters and settings: System-Memory: 12GB Processor: Intel 7-920 Quadcore Operating system: Debian 5 (lenny) 64bit MySQL 5.1.49 Databases: (a) a small phpbb forum (b) a 6GB database 3 tables with about 15 million rows my.cnf # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = our-ip-address # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 256K thread_cache_size = 32 max_connections = 300 table_cache = 2048 #thread_concurrency = 4 # Used for InnoDB tables recommended to 50%-80% available memory innodb_buffer_pool_size = 6G # 20MB sometimes larger innodb_additional_mem_pool_size = 20M # 8M-16M is good for most situations innodb_log_buffer_size = 8M # Disable XA support because we do not use it innodb-support-xa = 0 # 1 is default wich is 100% secure but 2 offers better performance innodb_flush_log_at_trx_commit = 1 innodb_flush_method = O_DIRECT #innodb_thread_concurency = 8 # Recommended 64M - 512M depending on server size innodb_log_file_size = 512M # One file per table innodb_file_per_table # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 16M #query_cache_type = 1 #query_cache_min_res_unit= 2K #join_buffer_size = 1M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog. This is a Debian improvement :) # # Here you can see queries with especially long duration log_slow_queries = /var/log/mysql/mysql-slow.log long_query_time = 2 log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. #server-id = 1 log_bin = /var/log/mysql/mysql-bin.log # WARNING: Using expire_logs_days without bin_log crashes the server! See README.Debian! expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # * InnoDB plugin # As of MySQL 5.1.38, the InnoDB plugin from Oracle is included in the MySQL source code. # It has many improvements and better performances than the built-in InnoDB storage engine. # Please read http://www.innodb.com/products/innodb_plugin/ for more information. # Uncommenting the two following lines to use the InnoDB plugin. ignore_builtin_innodb plugin-load=innodb=ha_innodb_plugin.so # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * NDB Cluster # # See /usr/share/doc/mysql-server-*/README.Debian for more information. # # The following configuration is read by the NDB Data Nodes (ndbd processes) # not from the NDB Management Nodes (ndb_mgmd processes). # # [MYSQL_CLUSTER] # ndb-connectstring=127.0.0.1 # # * IMPORTANT: Additional settings that can override those from this file! # !includedir /etc/mysql/conf.d/ UPDATE After installing sysstat and configuring it to collect data after every minute i have the following datas. I used sar to generate the following output: The log-file is too big so coudn't enter it here but uploaded to box.net. The link is http://www.box.net/shared/xc6rh7qqob SECOND UPDATE We started a ping command in the background, and that solved the problem. Now the server does work since more then a week. We still don't know what's the problem.

  Read the article

• Databinding to ObservableCollection in a different UserControl - how to preserve current selections?

  - by Dave

  Scope of question expanded on 2010-03-25 I ended up figuring out my problem, but here's a new problem that came up as a result of solving the original question, because I want to be able to award the bounty to someone!!! Once I figured out my problem, I soon found out that when the ObservableCollection updates, the databound ComboBox has its contents repopulated, but most of the selections have been blanked out. I assume that in this case, MVVM is going to make it difficult for me to remember the last selected item. I have an idea, but it seems a little nasty. I'll award the bounty to whomever comes up with a nice solution for this! Question re-written on 2010-03-24 I have two UserControls, where one is a dialog that has a TabControl, and the other is one that appears within said TabControl. I'll just call them CandyDialog and CandyNameViewer for simplicity's sake. There's also a data management class called Tracker that manages information storage, which for all intents and purposes just exposes a public property that is an ObservableCollection. I display the CandyNameViewer in CandyDialog via code behind, like this: private void CandyDialog_Loaded( object sender, RoutedEventArgs e) { _candyviewer = new CandyViewer(); _candyviewer.DataContext = _tracker; candy_tab.Content = _candyviewer; } The CandyViewer's XAML looks like this (edited for kaxaml): <Page xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml"> <Page.Resources> <DataTemplate x:Key="CandyItemTemplate"> <Grid> <Grid.ColumnDefinitions> <ColumnDefinition Width="120"></ColumnDefinition> <ColumnDefinition Width="150"></ColumnDefinition> </Grid.ColumnDefinitions> <TextBox Grid.Column="0" Text="{Binding CandyName}" Margin="3"></TextBox> <!-- just binding to DataContext ends up using InventoryItem as parent, so we need to get to the UserControl --> <ComboBox Grid.Column="1" SelectedItem="{Binding SelectedCandy, Mode=TwoWay}" ItemsSource="{Binding RelativeSource={RelativeSource FindAncestor, AncestorType={x:Type UserControl}}, Path=DataContext.CandyNames}" Margin="3"></ComboBox> </Grid> </DataTemplate> </Page.Resources> <Grid> <ListBox DockPanel.Dock="Top" ItemsSource="{Binding CandyBoxContents, Mode=TwoWay}" ItemTemplate="{StaticResource CandyItemTemplate}" /> </Grid> </Page> Now everything works fine when the controls are loaded. As long as CandyNames is populated first, and then the consumer UserControl is displayed, all of the names are there. I obviously don't get any errors in the Output Window or anything like that. The issue I have is that when the ObservableCollection is modified from the model, those changes are not reflected in the consumer UserControl! I've never had this problem before; all of my previous uses of ObservableCollection updated fine, although in those cases I wasn't databinding across assemblies. Although I am currently only adding and removing candy names to/from the ObservableCollection, at a later date I will likely also allow renaming from the model side. Is there something I did wrong? Is there a good way to actually debug this? Reed Copsey indicates here that inter-UserControl databinding is possible. Unfortunately, my favorite Bea Stollnitz article on WPF databinding debugging doesn't suggest anything that I could use for this particular problem.

  Read the article

• Optimizing MySQL for small VPS

  - by Chris M

  I'm trying to optimize my MySQL config for a verrry small VPS. The VPS is also running NGINX/PHP-FPM and Magento; all with a limit of 250MB of RAM. This is an output of MySQL Tuner... -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.41-3ubuntu12.8 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: -Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 1M (Tables: 14) [--] Data in InnoDB tables: 29M (Tables: 301) [--] Data in MEMORY tables: 1M (Tables: 17) [!!] Total fragmented tables: 301 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 2d 11h 14m 58s (1M q [8.038 qps], 33K conn, TX: 2B, RX: 618M) [--] Reads / Writes: 83% / 17% [--] Total buffers: 122.0M global + 8.6M per thread (100 max threads) [!!] Maximum possible memory usage: 978.2M (404% of installed RAM) [OK] Slow queries: 0% (37/1M) [OK] Highest usage of available connections: 6% (6/100) [OK] Key buffer size / total MyISAM indexes: 32.0M/282.0K [OK] Key buffer hit rate: 99.7% (358K cached / 1K reads) [OK] Query cache efficiency: 83.4% (1M cached / 1M selects) [!!] Query cache prunes per day: 48301 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 144K sorts) [OK] Temporary tables created on disk: 13% (27K on disk / 203K total) [OK] Thread cache hit rate: 99% (6 created / 33K connections) [!!] Table cache hit rate: 0% (32 open / 51K opened) [OK] Open file limit used: 1% (20/1K) [OK] Table locks acquired immediately: 99% (1M immediate / 1M locks) [!!] InnoDB data size / buffer pool: 29.2M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Reduce your overall MySQL memory footprint for system stability Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 64M) table_cache (> 32) innodb_buffer_pool_size (>= 29M) and this is the config. # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 32M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 sort_buffer_size = 4M read_buffer_size = 4M myisam_sort_buffer_size = 16M # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 100 table_cache = 32 tmp_table_size = 128M #thread_concurrency = 10 # # * Query Cache Configuration # #query_cache_limit = 1M query_cache_type = 1 query_cache_size = 64M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 log_error = /var/log/mysql/error.log # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ The site contains 1 wordpress site,so lots of MYISAM but mostly static content as its not changing all that often (A wordpress cache plugin deals with this). And the Magento Site which consists of a lot of InnoDB tables, some MyISAM and some INMEMORY. The "read" side seems to be running pretty well with a mass of optimizations I've used on Magento, the NGINX setup and PHP-FPM + XCACHE. I'd love to have a kick in the right direction with the MySQL config so I'm not blindly altering it based on the MySQLTuner without understanding what I'm changing. Thanks

  Read the article

• FFmpeg audio dont work in converted videos

  - by Juddy Swaft

  NOTICE: when i convert videos via terminal and download them from ftp into pc the audio works fine. I use: if($ext == "avi" && $convert_avi == true) { $convert_source = _VIDEOS_DIR_PATH.$new_name; $conv_name = substr(md5($file['name'].rand(1,888)), 2, 10).".mp4"; $converted_file = _VIDEOS_DIR_PATH.$conv_name; $ffmpeg_command = 'ffmpeg -i '.$convert_source.' -acodec libmp3lame -vcodec libx264 -s 1280x720 -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 '.$converted_file; echo exec($ffmpeg_command); $sql = "UPDATE pm_temp SET url = '".$conv_name."' WHERE url = '".$new_name."' LIMIT 1"; $result = @mysql_query($sql); unlink($convert_source); } This code to convert avi to mp4 ffmpeg concole output: root@1tb:~# ffmpeg -i sample.avi -acodec libmp3lame -vcodec libx264 -s 1280x720 -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 goodsample.mp4 ffmpeg version 0.7.15, Copyright (c) 2000-2013 the FFmpeg developers built on Feb 22 2013 07:18:58 with gcc 4.4.5 configuration: --enable-libdc1394 --prefix=/usr --extra-cflags='-Wall -g ' --cc='ccache cc' --enable-shared --enable-libmp3lame --enable-gpl --enable-libvorbis --enable-pthreads --enable-libfaac --enable-libxvid --enable-postproc --enable-x11grab --enable-libgsm --enable-libtheora --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libx264 --enable-libspeex --enable-nonfree --disable-stripping --enable-avfilter --enable-libdirac --disable-decoder=libdirac --enable-libfreetype --enable-libschroedinger --disable-encoder=libschroedinger - s libavutil 50. 43. 0 / 50. 43. 0 libavcodec 52.123. 0 / 52.123. 0 libavformat 52.111. 0 / 52.111. 0 libavdevice 52. 5. 0 / 52. 5. 0 libavfilter 1. 80. 0 / 1. 80. 0 libswscale 0. 14. 1 / 0. 14. 1 libpostproc 51. 2. 0 / 51. 2. 0 [mp3 @ 0x191d4100] Header missing [mpeg4 @ 0x191d1dc0] Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'sample.avi': Metadata: encoder : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:01:01.81, start: 0.000000, bitrate: 1194 kb/s Stream #0.0: Video: mpeg4, yuv420p, 640x352 [PAR 1:1 DAR 20:11], 23.98 tbr, Stream #0.1: Audio: mp3, 48000 Hz, stereo, s16, 128 kb/s [buffer @ 0x191d1c80] w:640 h:352 pixfmt:yuv420p tb:1/1000000 sar:1/1 sws_param: [scale @ 0x191d6880] w:640 h:352 fmt:yuv420p -> w:1280 h:720 fmt:yuv420p flags:0 [libx264 @ 0x191ce5a0] Default settings detected, using medium profile [libx264 @ 0x191ce5a0] using SAR=45/44 [libx264 @ 0x191ce5a0] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle S [libx264 @ 0x191ce5a0] profile High, level 3.1 [libx264 @ 0x191ce5a0] 264 - core 118 - H.264/MPEG-4 AVC codec - Copyleft 2003-2 6 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_off 1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_l Output #0, mp4, to 'goodsample.mp4': Metadata: encoder : Lavf52.111.0 Stream #0.0: Video: libx264, yuv420p, 1280x720 [PAR 45:44 DAR 20:11], q=2-31 Stream #0.1: Audio: libmp3lame, 44100 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop, [?] for help [mp3 @ 0x191d4100] Header missing Error while decoding stream #0.1 [mpeg4 @ 0x191d1dc0] Invalid and inefficient vfw-avi packed B frames detected [mp3 @ 0x191d4100] incomplete frame 9467kB time=00:01:00.32 bitrate=1285.5kbits/ Error while decoding stream #0.1 frame= 1852 fps= 20 q=29.0 Lsize= 9652kB time=00:01:01.72 bitrate=1280.9kbits video:9121kB audio:483kB global headers:0kB muxing overhead 0.499688% frame I:11 Avg QP:16.78 size: 51456 [libx264 @ 0x191ce5a0] frame P:784 Avg QP:20.81 size: 8954 [libx264 @ 0x191ce5a0] frame B:1057 Avg QP:26.06 size: 1659 [libx264 @ 0x191ce5a0] consecutive B-frames: 22.0% 3.1% 7.5% 67.4% [libx264 @ 0x191ce5a0] mb I I16..4: 31.1% 59.8% 9.1% [libx264 @ 0x191ce5a0] mb P I16..4: 1.8% 2.6% 0.2% P16..4: 24.3% 7.0% 4.0 [libx264 @ 0x191ce5a0] mb B I16..4: 0.1% 0.1% 0.0% B16..8: 22.7% 0.8% 0.2 [libx264 @ 0x191ce5a0] 8x8 transform intra:57.0% inter:72.6% [libx264 @ 0x191ce5a0] coded y,uvDC,uvAC intra: 44.4% 33.3% 10.3% inter: 7.6% 5. [libx264 @ 0x191ce5a0] i16 v,h,dc,p: 68% 14% 8% 10% [libx264 @ 0x191ce5a0] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 21% 14% 27% 5% 7% 7% 6 [libx264 @ 0x191ce5a0] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 28% 14% 14% 6% 10% 9% 7 [libx264 @ 0x191ce5a0] i8c dc,h,v,p: 67% 13% 17% 3% [libx264 @ 0x191ce5a0] Weighted P-Frames: Y:1.9% UV:0.4% [libx264 @ 0x191ce5a0] ref P L0: 62.2% 12.8% 10.3% 14.5% 0.2% [libx264 @ 0x191ce5a0] ref B L0: 88.1% 5.5% 6.4% [libx264 @ 0x191ce5a0] ref B L1: 95.7% 4.3% [libx264 @ 0x191ce5a0] kb/s:1209.03 I know there is couple errors tough, but i dont know hot to fix it. Also i would be very thankfull if someone can help reduce video size but is not main problem video weights as original avi but sill.

  Read the article

< Previous Page | 442 443 444 445 446 447 448 449 450 451 452 453  | Next Page >