Search Results

Search found 11645 results on 466 pages for 'win xp'.

Page 447/466 | < Previous Page | 443 444 445 446 447 448 449 450 451 452 453 454  | Next Page >

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either.

  Read the article

• VMWare Network bug in multiple VMWare Workstation versions if using a hardcoded IP address

  - by onyxruby

  I'm having a very tricky problem with some of my VM sessions being unable to reach the Internet or even ping the gateway. I have just set up a new VM Workstation (7) on a W2K8 64bit server (I'll be converting to ESXI 4 once I can find a decent book on it, so for the meanwhile I use workstation). I have imported a number of VM's and setup some new ones on the server.In short the problem with some of the VM's being unable to reach the Internet is that they can't reach the gateway. I've looking at a number of things and can pretty safely rule out the following: Switch, Router, DHCP Server, DNS, Client IP configuration, Routes and typos. The problem is that some of the new clients cannot reach the gateway if their IP address is hardcoded, they can't even ping it by IP address. That rules out DNS and DHCP. Now, if I allow them to get their IP address by DHCP they can reach the gateway and Internet without issue. The interesting thing on this, is that this behavior occurs even if I leave the DNS information hardcoded under TCP/IP settings. It doesn't work unless the IP and gateway are handed out by DHCP even though the same information IP info is being used by the host. Fundamentally from the standpoint of the clients, they are trying to reach the exact same gateway using the exact same IP information regardless of whether they are hardcoded or assigned by DHCP. Here's an example of one client. IP Address 192.168.7.66 - Subnet Mask 255.255.255.0 - Gateway 192.168.7.254 - DNS1 192.168.7.44 - DNS2 192.168.7.254. The issue occurs across six different microsoft operating systems, Windows 7 and Windows 2008 variants all have the issue. My W2K3, XP, Vista and W98 clients all work without issue with hardcoded IP addresses. I have tried things like rearranging the DNS order, flushing DNS and so on. It's not a routing or switch issue as the clients can work just fine if they get their IP by DHCP. It's not a paramater issue as the exact same paramaters are handed out by DHCP as I plug in by hand. It's not a DNS issue as clients cant reach other clients even with IP addresses only. I have run a tracert to the gateway by IP address and it times out on the very first hop before failing on hop3 with destination host unreachable. If I get the IP address by DHCP the tracert finds the gateway (and Internet) without issue. I have read a few other posts online in forums talking about this problem randomly occuring over the years in other VM versions as well, so I suspect some kind of long standing bug. Does anyone have any ideas on this? Is it possibly a bug with Windows 7 and W2K clients under VM?

  Read the article

• Windows 7 boot problem (with colorful blinking smilies)

  - by Ishmael Smyrnow

  I put my computer (Windows 7) to sleep, and a couple hours later, tried to wake it back up, but the monitor wouldn't come back on. I did a hard reset (held power button), but I still couldn't get the monitor to show anything. I plugged it into my laptop, and the monitor works fine. I then swapped out the video card with an older one I have. The monitor came on and started showing the boot process. However, shortly after the Windows 7 animated logo came up, the screen went blank, it made this weird beeping noise, and I seen the strangest thing ever. Small, colorful blocks started to fill my screen, and flash, as if something was loading. Inside of those blocks, were smilies (like the ASCII character kind). This continued for about a minute, then the computer rebooted. It scared the sh!t out of me. I've never had a virus before, and I'm savvy enough to keep myself from one, but I'm wondering if that's what it was. I've been using computers for ages, and never seen anything quite like this. Has anyone ever seen something like this? I'm doing hardware diagnostics before trying to boot into Windows again. Hopefully I can figure this out, but I thought I would consult the SU community while I wait on these results. -- UPDATE -- I did a Memory Diagnostic, which turned up nothing. I also booted into Safe Mode no problem, and scheduled a disk check on both of my drives (I dual boot XP & 7). I was feeling good, and tried putting my regular video card back in, and the monitor won't display anything with it. Also, even though the monitor displays nothing, the system sounds like it's booting up. However, I hear a clicking in one of my hard drives that isn't there with the older video card. Could this be a problem with my hard drive, video card, or PSU? PSU makes sense, except for the fact I've been using the same setup for over a year, and the video card doesn't require it's own power plug thing.

  Read the article

• Triple monitor setup in linux

  - by Brendan Abel

  I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

  Read the article

• In search of a network file system with extended caching to speed up file access

  - by Brecht Machiels

  I'm running a small home server that stores my documents. The disks in this server are in a RAID 1 configuration (using Linux md) and it's also periodically being backup up to an external hard drive to make sure I don't lose them. However, I'm always accessing the files from other computers on the home network using an SMB share, and this results in a considerable speed penalty (especially when connected over WLAN). This is quite annoying when editing large files, such as digital camera RAWs, for example. I've been looking for a solution to this problem. It would have to offer some kind of local caching to speed up the file access. The client would preferably not keep a copy of all data on the server, as it consists of a very large collection of photographs, most of which I will not access frequently. Instead, it should only cache the accessed files and sync the changes back in the background. Ideally, it would also do some smart read-ahead (cache the files that are in the same directory as the currently opened file, for examples), but I suppose that's asking a bit much. Synchronization should be automatic (on file change). Conflicting file changes (at the same time on different clients) are unlikely to happen in my use case, but I would prefer if they are handled properly (notification to the user). I've come across the following options, so far: something similar to Dropbox. iFolder seems to be the only thing that comes close, but its reputation (stability) and requirements put me off. A distributed file system such as OpenAFS. I'm not sure this will speed up file access. It is probably overkill for what I need. Maybe NFS or even Samba offer these possibilities. I read a bit about Windows' Offline Files, but its operation seems limited (at least on Windows XP). As this is just for personal use, I'm not willing to spend a lot of money. A free solution would be preferred. Also, the server needs to run on Linux, and I need a client for at least Windows.

  Read the article

• Can you set up a gaming LAN using OpenVPN installed in a VMware guest OS and be playing the game on the host OS?

  - by Coder

  I would like to setup a gaming VPN. Ie. I have some games that work over LAN and would like to play them with people that are not on my LAN. I know I can do this with OpenVPN. My ultimate goal would be to run OpenVPN portably on my host OS and not even need any virtualization. As such i don't want to install it on my host, but i'm fine with running it portably. I'm even fine with temporarily adding registry keys, and then running a .reg file to remove these entries once i'm done. To this effect i have installed OpenVPN on a virtual machine and diffed the registry. I then manually (using a .reg file) added all the keys that seem important on my host OS and copied the installation folder of OpenVPN onto my host machine. Then i try to run openVPN GUI 1.0.3 as a test and it says "Error opening registy for reading (HKLM\SOFTWARE\OpenVPN). OpenVPN is probably not installed". I verified that that key is indeed in the registry with all subkeys and it looks correct. I have tried running the GUI as an administrator and in compatibility mode with no success. I am running Windows 7. If this fails then i would be happy with installing OpenVPN on a virtual machine in VMWare but they key is that i will be running the game installed on my host machine. The first question for this option is if this is even possible. The second is, that I can't get the VM to have internet access if I use bridging but i can if i use NAT. Is it possible to do this game VPN setup with VMWare guest OS running using NAT? Summary of questions: -Is it possible to run openVPN portably and if so what did i miss above? -If it's not possible to run it portably, then can setup a gaming LAN by installing OpenVPN in a guest OS with NAT and how can i do this? -If the above is not possible then can i install OpenVPN in a guest using bridging and if so how can i set this up with a Windows 7 host and Windows XP guest as currently i can't get the guest to be able to access the internet in bridging mode, but it working in NAT mode. -In general is there any good documentation on setting up a gaming LAN with OpenVPN (i am using 2.1.4) as i have never set up a VPN of any sort before so any help would be much appreciated. Thanks!

  Read the article

• OS X Snow Leopard 10.6 Refuses to Load Websites the first time intermittently

  - by Brandon

  Many times when I am browsing the web, Snow Leopard will sit and load a site for 20 seconds or more, until it times out and says it cannot be displayed. If I refresh, it loads RIGHT away, every time. The issue is intermittent but happens from once every couple of days to a few times a day. So the long and short of it is this: Aluminum MacBook (Non-Pro) 2.4GHz Core2Duo, 4GB DDR3 I am using 10.6.6 but I have had this issue since 10.6.0 It happens in Firefox, Chrome, and Safari I have flushed my DNS (using the command 'blablabla flush') I am using custom DNS servers which I hoped would fix it but it had no effect* I am running Apache currently but haven't been for most of the time I've reformatted multiple times, always experiencing the issue I am on Cox cable internet, with a Motorola Surfboard & a Belkin F6D4230-4 v1 (Pre?) N wireless router. I've put the router in G only & N only & G+N to no effect It seems to be domain dependant as I can sometimes load the Google cache right away, and sometimes other sites will load but Google will refuse My Powerbook G4 with Leopard, other Windows XP laptops, & my wired Win7 desktop do not suffer from the issue. *I recently started using these to escape the awful Cox redirect page on timeouts I'm almost positive the issue has happened on other networks but I can't recall a specific instance (I have a terrible memory). The problem is intermittent and fixable enough (I just have to wait until it times out and hit refresh one time) but incredibly annoying since I'm constantly reading documentation from a large variety of sites. EDIT: To clarify, this happens with ALL sites, not only specific sites. I haven't been able to detect any pattern to the failures, but one day Google.com will refuse to load while reddit.com will, and the next day vice versa. Keep in mind that waiting for a timeout and hitting refresh loads the page right away, every time. If I don't wait for the timeout, opening more links, hitting refresh, and clicking the link a billion times have no effect. It seems to be domain neutral, affecting sites seemingly at random. It doesn't seem to have anything to do with connection inactivity either, because I will be SSHed into different servers, uploading files, browsing, downloading, etc, and it will just quit loading Jquery.com (for example) until I sit and wait for a timeout. /EDIT This is my last resort. Please, someone, tell me what is happening. Thank you.

  Read the article

• Splitting an internet connection between multiple separate subnetworks

  - by pythonian4000

  Problem I have an internet connection that I want to split between four separate networks. My requirements are: I need to be able to monitor the amount of bandwidth and data being used by each network, and notify or control as necessary. The four networks should only be able to connect to the internet, not each other. My parents need to be able to operate it, so it needs a simple, preferably Windows-based GUI. Progress so far Server I have a mini-ITX server with six Gigabit ethernet ports - one for the ethernet internet connection, one for each of the four networks, and one for remote access to the server for administration. Bandwidth control I spent a long time researching solutions here. The majority of the control systems/software I found could control bandwidth usage via QOS, but could not monitor or control the amount of data being used. Eventually I found the SoftPerfect Bandwidth Manager, which has everything I need in terms of monitoring and control - per-interface quota management, usage statistics, a web interface for checking usage, and email notifications when quotas are exceeded. It is also Windows-based and has a simple GUI. Internet sharing This is where I am having issues. I am currently using Windows XP Pro SP2 for the server (yes, I know this is far from ideal, but it's the only spare Windows OS I currently have). I can't use the built-in Internet Connection Sharing for several reasons: The upstream internet router has an IP of 192.168.0.1 which ICS clashes with, and I cannot change the router settings. ICS can only share an internet connection with a single interface, but I have four. I have tried bridging the four network cards, but then the Bandwidth Manager cannot see the four individual interfaces - it only sees the bridge. I have tried setting up Dual DHCP DNS server (and am having issues getting DHCP offers to be received by clients), but that would still require gateway software of some sort, which I have been unable to find. My current attempt is to use OpenVPN, with a server for the internet NIC and a separate client for each of the four networks. My thought is that I could bridge the OpenVPN TAP devices to each NIC, meaning that the Bandwidth Manager would control traffic from the bridge instead of the interface. I have not made much progress here though - I've never used OpenVPN before. Questions Is there a Windows software package that does everything I need? (Unlikely, I know) Is there a Windows software package that will share internet between multiple NICs without bridging? Are either of my about attempts feasible? Would it help to have a newer/server version of Windows? Is there a non-Windows alternative that is easy to use?

  Read the article

• How to disable hiddev96 in linux (or tell it to ignore a specific device)

  - by Miky D

  I'm having problems with a CentOS 5.0 system when using a certain USB device. The problem is that the device advertises itself as a HID device and linux is happy to try to provide support for it: In /ver/log/messages I see a line that reads: hiddev96: USB HID 1.11 Device [KXX USB PRO] on usb-0000:00:1d.0-1 My question comes down to: Is there a way to tell linux to not use hiddev96 for that device in particular? If yes, how? If not, what are my options - can I turn hiddev96 off completely? UPDATE I should probably have been a bit more specific about what is going on. The machine is running Centos 5.0, and on top of it I'm running VMWare workstation with Windows XP - which is where the USB device is actually supposed to operate. All works fine for other USB devices (i.e. VMWare successfully connects the USB device to the guest OS and the OS can use it, but for this particular device VMWare connects it to the guest OS, but the OS can't read/write to it) Every attempt locks up the application that is trying to communicate with the device. I've reason to believe that it is because the device is a HID device and there's some contention between the Linux host and the Windows guest OS in accessing the device. Below is the output from modprobe -l|grep -i hid as requested by @Karolis: # modprobe -l | grep -i hid /lib/modules/2.6.18-53.1.14.el5/kernel/net/bluetooth/hidp/hidp.ko /lib/modules/2.6.18-53.1.14.el5/kernel/drivers/usb/misc/phidgetservo.ko /lib/modules/2.6.18-53.1.14.el5/kernel/drivers/usb/misc/phidgetkit.ko And here is the output of lsmod # lsmod Module Size Used by udf 76997 1 vboxdrv 65696 0 autofs4 24517 2 hidp 23105 2 rfcomm 42457 0 l2cap 29633 10 hidp,rfcomm tun 14657 0 vmnet 49980 16 vmblock 20512 3 vmmon 945236 0 sunrpc 144253 1 cpufreq_ondemand 10573 1 video 19269 0 sbs 18533 0 backlight 10049 0 i2c_ec 9025 1 sbs button 10705 0 battery 13637 0 asus_acpi 19289 0 ac 9157 0 ipv6 251393 27 lp 15849 0 snd_hda_intel 24025 2 snd_hda_codec 202689 1 snd_hda_intel snd_seq_dummy 7877 0 snd_seq_oss 32577 0 nvidia 7824032 31 snd_seq_midi_event 11073 1 snd_seq_oss snd_seq 49713 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 11725 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 42945 0 snd_mixer_oss 19009 1 snd_pcm_oss snd_pcm 72133 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss joydev 13313 0 sg 36061 0 parport_pc 29157 1 snd_timer 24645 2 snd_seq,snd_pcm snd 52421 13 snd_hda_intel,snd_hda_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer ndiswrapper 170384 0 parport 37513 2 lp,parport_pc hci_usb 20317 2 ide_cd 40033 1 tg3 104389 0 i2c_i801 11469 0 bluetooth 53925 8 hidp,rfcomm,l2cap,hci_usb soundcore 11553 1 snd cdrom 36705 1 ide_cd serio_raw 10693 0 snd_page_alloc 14281 2 snd_hda_intel,snd_pcm i2c_core 23745 3 i2c_ec,nvidia,i2c_i801 pcspkr 7105 0 dm_snapshot 20709 0 dm_zero 6209 0 dm_mirror 28741 0 dm_mod 58201 8 dm_snapshot,dm_zero,dm_mirror ahci 23621 4 libata 115833 1 ahci sd_mod 24897 5 scsi_mod 132685 3 sg,libata,sd_mod ext3 123337 3 jbd 56553 1 ext3 ehci_hcd 32973 0 ohci_hcd 23261 0 uhci_hcd 25421 0

  Read the article

• How to iptables forward ppp0 to eth0

  - by HPHPHP2012

  need your help with get it routing properly. I've server with eth0 (external interface) and eth1(internal interface). eth1 is merged into the bridge br0 (172.16.1.1) I've installed the pptp and successfully configured it, so I got ppp0 interface (192.168.91.1) and got my VPN clients successfully connected. So I need your help to manage how to allow my VPN clients use internet connection (eth0). Below my configuration files, any help is much appreciated! Thank you! P.S. VPN clients are Windows Xp, Windows 7, Mac OS X Lion, Ubuntu 12.04, iOS 5.x cat /etc/pptpd.conf #local server ip address localip 192.168.91.1 #remote addresses remoteip 192.168.91.11-254,192.168.91.10 #translating ip addresses on this interface bcrelay br0 cat /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 8.8.8.8 ms-dns 8.8.4.4 nodefaultroute lock nobsdcomp auth logfile /var/log/pptpd.log cat /etc/nat-up #!/bin/sh SERVER_IP="aaa.aaa.aaa.aaa" LOCAL_IP="172.16.1.1" #eth0 with public ip PUBLIC="eth0" #br0 is internal bridge on eth1 interface INTERNAL="br0" #vpn VPN="ppp0" #local LOCAL="lo" iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT ACCEPT echo 1 > /proc/sys/net/ipv4/ip_forward iptables -A INPUT -i $LOCAL -j ACCEPT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i $PUBLIC -j ACCEPT ####CLEAR CONFIG#### #iptables -A FORWARD -i $PUBLIC -o $INTERNAL -m state --state ESTABLISHED,RELATED -j ACCEPT #iptables -A FORWARD -i $PUBLIC -o $INTERNAL -j ACCEPT #iptables -A FORWARD -i $INTERNAL -o $PUBLIC -j ACCEPT #iptables -t nat -A POSTROUTING -j MASQUERADE ####THIS PART IS NOT HANDLING IT#### iptables -A FORWARD -i $PUBLIC -o $VPN -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i $PUBLIC -o $VPN -j ACCEPT iptables -A FORWARD -s 192.168.91.0/24 -o $PUBLIC -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.91.0/24 -o $PUBLIC -j MASQUERADE # VPN - PPTPD iptables -A INPUT -p gre -s 0/0 -j ACCEPT iptables -A OUTPUT -p gre -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --dport 1723 -j ACCEPT #SSH iptables -A INPUT -p tcp --dport 2222 -j ACCEPT iptables -A OUTPUT -p tcp --sport 2222 -j ACCEPT #BLACKLIST BLOCKDB="/etc/ip.blocked" IPS=$(grep -Ev "^#" $BLOCKDB) for i in $IPS do iptables -A INPUT -s $i -j DROP iptables -A OUTPUT -d $i -j DROP done

  Read the article

• Exposing the AnyConnect HTTPS service to outside network

  - by Maciej Swic

  We have a Cisco ASA 5505 with firmware ASA9.0(1) and ASDM 7.0(2). It is configured with a public ip address, and when trying to reach it from the outside by HTTPS for AnyConnect VPN, we get the following log output: 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Built inbound TCP connection 2889 for outside:<client-ip>/51000 (<client-ip>/51000) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Built inbound TCP connection 2890 for outside:<client-ip>/50999 (<client-ip>/50999) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Teardown TCP connection 2889 for outside:<client-ip>/51000 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Teardown TCP connection 2890 for outside:<client-ip>/50999 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency We finished the startup wizard and the anyconnect vpn wizard and here is the resulting configuration: Cryptochecksum: 12262d68 23b0d136 bb55644a 9c08f86b : Saved : Written by enable_15 at 07:08:30.519 UTC Mon Nov 12 2012 ! ASA Version 9.0(1) ! hostname vpn domain-name office.<redacted>.com enable password <redacted> encrypted passwd <redacted> encrypted names ip local pool vpn-pool 192.168.67.2-192.168.67.253 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.68.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address <redacted> 255.255.255.248 ! ftp mode passive dns server-group DefaultDNS domain-name office.<redacted>.com object network obj_any subnet 0.0.0.0 0.0.0.0 pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu inside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected ! object network obj_any nat (inside,outside) dynamic interface timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL http server enable http 192.168.68.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto ca trustpoint _SmartCallHome_ServerCA crl configure crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=vpn proxy-ldc-issuer crl configure crypto ca trustpool policy crypto ca certificate chain _SmartCallHome_ServerCA certificate ca 6ecc7aa5a7032009b8cebcf4e952d491 <redacted> quit crypto ca certificate chain ASDM_TrustPoint0 certificate f678a050 <redacted> quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable outside client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 ssh 192.168.68.0 255.255.255.0 inside ssh timeout 5 console timeout 0 vpn-addr-assign local reuse-delay 60 dhcpd auto_config outside ! dhcpd address 192.168.68.254-192.168.68.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ssl trust-point ASDM_TrustPoint0 inside ssl trust-point ASDM_TrustPoint0 outside webvpn enable outside enable inside anyconnect image disk0:/anyconnect-win-3.1.01065-k9.pkg 1 anyconnect image disk0:/anyconnect-linux-3.1.01065-k9.pkg 2 anyconnect image disk0:/anyconnect-macosx-i386-3.1.01065-k9.pkg 3 anyconnect profiles GM-AnyConnect_client_profile disk0:/GM-AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy GroupPolicy_GM-AnyConnect internal group-policy GroupPolicy_GM-AnyConnect attributes wins-server none dns-server value 192.168.68.254 vpn-tunnel-protocol ikev2 ssl-client default-domain value office.<redacted>.com webvpn anyconnect profiles value GM-AnyConnect_client_profile type user username <redacted> password <redacted> encrypted tunnel-group GM-AnyConnect type remote-access tunnel-group GM-AnyConnect general-attributes address-pool vpn-pool default-group-policy GroupPolicy_GM-AnyConnect tunnel-group GM-AnyConnect webvpn-attributes group-alias GM-AnyConnect enable ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context call-home reporting anonymous Cryptochecksum:12262d6823b0d136bb55644a9c08f86b : end Clearly we are missing something, but the question is, what?

  Read the article

• Setting up SSL on apache on linux ubuntu

  - by ThomasReggi

  I'm trying to get SSL to run on my apache web server. I do not have the DNS for the domain setup yet is that an issue? How do I setup SSL on my web server? When I start apache it fails. root@vannevar:/etc/apache2/ssl# service apache2 start * Starting web server apache2 Action 'start' failed. The Apache error log may have more information. The log stats that it's unable to read the certificate. [Thu Jun 28 15:01:02 2012] [error] Init: Unable to read server certificate from file /etc/apache2/ssl/www.example.com.csr [Thu Jun 28 15:01:02 2012] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag [Thu Jun 28 15:01:02 2012] [error] SSL Library Error: 218595386 error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error The contents of /etc/apache2/httpd.conf ServerName [SERVERIP] The contents of /etc/apache2/ports.conf # If you just change the port or add more ports here, you will likely also # have to change the VirtualHost statement in # /etc/apache2/sites-enabled/000-default # This is also true if you have upgraded from before 2.2.9-3 (i.e. from # Debian etch). See /usr/share/doc/apache2.2-common/NEWS.Debian.gz and # README.Debian.gz NameVirtualHost [SERVERIP]:443 NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> The contents of /etc/apache2/sites-available/www.example.com <VirtualHost *:80> ServerAdmin [email protected] ServerName example.com ServerAlias www.example.com DocumentRoot /srv/sites/example.com/public/ ErrorLog /srv/sites/example.com/logs/error.log CustomLog /srv/sites/example.com/logs/access.log combined </VirtualHost> <VirtualHost [SERVERIP]:443> SSLEngine On SSLCertificateFile /etc/apache2/ssl/www.example.com.csr SSLCertificateKeyFile /etc/apache2/ssl/www.example.com.key SSLCACertificateFile /etc/apache2/ssl/comodo.crt ServerAdmin [email protected] ServerName example.com ServerAlias www.example.com DocumentRoot /srv/sites/example.com/public/ ErrorLog /srv/sites/example.com/logs/error.log CustomLog /srv/sites/example.com/logs/access.log combined </VirtualHost>

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Impossible to create/format install window 7 on unpartioned HD

  - by fra pet

  Hi guys i am getting nut reinstalling windows 7 on one of those Acer aspire all-in-one... The original OS(windows professional x64) was not starting, after the initial screen the bios was prompted. So step 1: i tried to access the system partition and reinstall everything but could not get at the point step 2: i set the bios to native ide and i tried to insert my original copy of windows professional and do a clean installation, but it does not allow me to format/create other partion form the installation mask step 3: my BAD, i tried to install ubuntu and i clean the whole hard drive, i was getting an error at some point during installation so i decided to get back to windows step 4: Windows 7 again, at the disk screen of the windows installation i entered into the prompt and played around with DISKPART... -i listed the disk and the HD was disk 0. -i selected disk 0. -i CLEAN disk 0 successfully. -i tried to create a CREATE PARTITION PRIMARY but gave an error cache corrupt and disk not up-to-date (after i try to create a partiton in disk 0 it disappear when i try LIST DISK and i have to restart before he can list DISK 0 again, RESCAN did not worked). -tried CLEAN ALL(2 hours) and succeeded. -try again to create primary partition and failed, same errors -try to install my old copy of windows xP pro and it seems to work, it create a partition, format(only quick worked, slow mode was at 0% after 1 hour so i stop), it start installing and around 90% installation said it could not copy a file and he stop -back on windows 7 again, it says that the hard drive has 490+gb unpartitioned but won't create a partition and format. -i tried again DISKPART as i though i messed up with the MBR when i installed ubuntu, so i did all of the instruction below http://www.sevenforums.com/tutorials/20864-mbr-restore-windows-7-master-boot-record.html http://support.microsoft.com/kb/927392 the errors were: on bootsect: the systne partiton was not found, Data error cyclic redundancy check on bootrec /FixMbr: A device attached to the system is not functioning but did not worked, and still can not partiton/format/install on a blank HD i tried some bootable clean disk tool and start infinite loop on the same errors the bios setting are: sata: native ide. if i put AHCL(or something like that does not load the HD and the DVD). quick start/quite start: disabled. Are there any other option or tools i can try before i try change the HD(That is my last option)? Thanks to everyone.

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Remote installing an msi on citrix servers using WMI

  - by capn

  OK, I'm a C# programmer that is trying to streamline the deployment of a custom windows form app I inherited and built an installer for with WiX (this app will need to be reinstalled regularly as I'm making changes to it). I'm not really used to admin type things (or vbs, or WMI, or terminal servers, or Citrix, and even WiX and MSI are not things I usually deal with) but so far I put together some vbs and have an end goal in mind. The msi does work, and I've installed it from the mapped O: drive on my dev machine and while RDP'd to a citrix machine. End Goal: Deploy code written on my dev machine and compiled into an MSI (that I can improve upon within the confines of WiX and whatever the Windows Installer Engine allows) to the cluster of Citrix machines my users have access to. What am I missing in my script to get the MSI to execute on the remote machines? Layout: Machine A is my dev machine, and has the vbs script and the msi file (XP SP3) Machines C1 - C6 are the Citrix Servers that need the application installed them via the msi (Server 2003 R2 SP2) There is also optionally a shared network resource that all the machines can access. Script: 'Set WMI Constants Const wbemImpersonationLevelImpersonate = 3 Const wbemAuthenticationLevelPktPrivacy = 6 'Set whether this is installing to the debug Citrix Servers Const isDebug = true 'Set MSI location 'Network location yields error 1619 (This installation package could not be opened.) msiLocation = "\\255.255.255.255\odrive\Citrix Deployment\Setup.msi" 'Directory on machine A yields error 3 (file not found) 'msiLocation = "C:\Temp\Deploy\Setup.msi" 'Mapped network drive (on both machines) yield error 3 (file not found) 'msiLocation = "O:\Citrix Deployment\Setup.msi" 'Set login information strDomain = "MyDomain" Wscript.StdOut.Write "user name:" strUser = Wscript.StdIn.ReadLine Set objPassword = CreateObject("ScriptPW.Password") Wscript.StdOut.Write "password:" strPassword = objPassword.GetPassword() 'Names of Citrix Servers Dim citrixServerArray If isDebug Then citrixServerArray = array("C4") Else 'citrixServerArray = array("C1","C2","C3","C5","C6") End If 'Loop through each Citrix Server For Each citrixServer in citrixServerArray 'Login to remote computer Set objLocator = CreateObject("WbemScripting.SWbemLocator") Set objWMIService = objLocator.ConnectServer(citrixServer, _ "root\cimv2", _ strUser, _ strPassword, _ "MS_409", _ "ntlmdomain:" + strDomain) 'Set Remote Impersonation level objWMIService.Security_.ImpersonationLevel = wbemImpersonationLevelImpersonate objWMIService.Security_.AuthenticationLevel = wbemAuthenticationLevelPktPrivacy 'Reference to a process on the machine Dim objProcess : Set objProcess = objWMIService.Get("Win32_Process") 'Change user to install for terminal services errReturn = objProcess.Create _ ("cmd.exe /c change user /install", Null, Null, intProcessID) WScript.Echo errReturn 'Install MSI here 'Reference to a product on the machine Set objSoftware = objWMIService.Get("Win32_Product") 'All users set in option parameter, I'm led to believe that the third parameter is actually ignored 'http://www.webmasterkb.com/Uwe/Forum.aspx/vbscript/2433/Installing-programs-with-VbScript errReturn = objSoftware.Install(msiLocation,"ALLUSERS=2 REBOOT=ReallySuppress",True) Wscript.Echo errReturn 'Change user back to execute errReturn = objProcess.Create _ ("cmd.exe /c change user /execute", Null, Null, intProcessID) WScript.Echo errReturn Next I also tried using this to install, it doesn't return an error code, but doesn't install the msi either, and it makes me wonder if the change user /install command is even really working. errReturn = objProcess.Create _ ("cmd.exe /c msiexec /i ""O:\Citrix Deployment\Setup.msi"" /quiet") Wscript.Echo errReturn

  Read the article

• Can't log in via SSH to any accounts set to use /bin/bash as a default shell

  - by Gui Ambros

  I'm trying to install bash as the default shell on a ARM Linux running on an embedded device (Synology DS212+ NAS). But there's something really wrong, and I can't figure out what it is. Symptoms: 1) Root has /bin/bash as default shell, and can log in normally via SSH: $ grep root /etc/passwd root:x:0:0:root:/root:/bin/bash $ ssh root@NAS root@NAS's password: Last login: Sun Dec 16 14:06:56 2012 from desktop # 2) joeuser has /bin/bash as default shell, and receives "Permission denied" when trying to log in via SSH: $ grep joeuser /etc/passwd joeuser:x:1029:100:Joe User:/home/joeuser:/bin/bash $ ssh joeuser@localhost joeuser@NAS's password: Last login: Sun Dec 16 14:07:22 2012 from desktop Permission denied, please try again. Connection to localhost closed. 3) changing joeuser's shell back to /bin/sh: $ grep joeuser /etc/passwd joeuser:x:1029:100:Joe User:/home/joeuser:/bin/sh $ ssh joeuser@localhost Last login: Sun Dec 16 15:50:52 2012 from localhost $ To make things even more strange, I can log in as joeuser using /bin/bash using the serial console (!). Also a su - joeuser as root works fine, so the bash binary itself is working fine. In an act of despair, I changed joeuser's uid to 0 on /etc/passwd, but also didn't work, so it doesn't seem to be anything permission related. Seems that bash is doing some extra checking that sshd didn't like, and blocking the connections for non-root users. Maybe some sort of sanity checking - or terminal emulation - that is triggering the SIGCHLD, but only when called via ssh. I already went through every single item on sshd_config, and also put SSHD in debug mode, but didn't find anything strange. Here's my /etc/ssh/sshd_config: LogLevel DEBUG LoginGraceTime 2m PermitRootLogin yes RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile %h/.ssh/authorized_keys ChallengeResponseAuthentication no UsePAM yes AllowTcpForwarding no ChrootDirectory none Subsystem sftp internal-sftp -f DAEMON -u 000 And here's the output from /usr/syno/sbin/sshd -d, showing the failed attempt of joeuser trying to log in, with /bin/bash as the shell: debug1: Config token is loglevel debug1: Config token is logingracetime debug1: Config token is permitrootlogin debug1: Config token is rsaauthentication debug1: Config token is pubkeyauthentication debug1: Config token is authorizedkeysfile debug1: Config token is challengeresponseauthentication debug1: Config token is usepam debug1: Config token is allowtcpforwarding debug1: Config token is chrootdirectory debug1: Config token is subsystem debug1: HPN Buffer Size: 87380 debug1: sshd version OpenSSH_5.8p1-hpn13v11 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: read PEM private key done: type ECDSA debug1: private host key: #2 type 3 ECDSA debug1: rexec_argv[0]='/usr/syno/sbin/sshd' debug1: rexec_argv[1]='-d' Set /proc/self/oom_adj from 0 to -17 debug1: Bind to port 22 on ::. debug1: Server TCP RWIN socket size: 87380 debug1: HPN Buffer Size: 87380 Server listening on :: port 22. debug1: Bind to port 22 on 0.0.0.0. debug1: Server TCP RWIN socket size: 87380 debug1: HPN Buffer Size: 87380 Server listening on 0.0.0.0 port 22. debug1: Server will not fork when running in debugging mode. debug1: rexec start in 6 out 6 newsock 6 pipe -1 sock 9 debug1: inetd sockets after dupping: 4, 4 Connection from 127.0.0.1 port 52212 debug1: HPN Disabled: 0, HPN Buffer Size: 87380 debug1: Client protocol version 2.0; client software version OpenSSH_5.8p1-hpn13v11 SSH: Server;Ltype: Version;Remote: 127.0.0.1-52212;Protocol: 2.0;Client: OpenSSH_5.8p1-hpn13v11 debug1: match: OpenSSH_5.8p1-hpn13v11 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8p1-hpn13v11 debug1: permanently_set_uid: 1024/100 debug1: MYFLAG IS 1 debug1: list_hostkey_types: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: AUTH STATE IS 0 debug1: REQUESTED ENC.NAME is 'aes128-ctr' debug1: kex: client->server aes128-ctr hmac-md5 none SSH: Server;Ltype: Kex;Remote: 127.0.0.1-52212;Enc: aes128-ctr;MAC: hmac-md5;Comp: none debug1: REQUESTED ENC.NAME is 'aes128-ctr' debug1: kex: server->client aes128-ctr hmac-md5 none debug1: expecting SSH2_MSG_KEX_ECDH_INIT debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: KEX done debug1: userauth-request for user joeuser service ssh-connection method none SSH: Server;Ltype: Authname;Remote: 127.0.0.1-52212;Name: joeuser debug1: attempt 0 failures 0 debug1: Config token is loglevel debug1: Config token is logingracetime debug1: Config token is permitrootlogin debug1: Config token is rsaauthentication debug1: Config token is pubkeyauthentication debug1: Config token is authorizedkeysfile debug1: Config token is challengeresponseauthentication debug1: Config token is usepam debug1: Config token is allowtcpforwarding debug1: Config token is chrootdirectory debug1: Config token is subsystem debug1: PAM: initializing for "joeuser" debug1: PAM: setting PAM_RHOST to "localhost" debug1: PAM: setting PAM_TTY to "ssh" debug1: userauth-request for user joeuser service ssh-connection method password debug1: attempt 1 failures 0 debug1: do_pam_account: called Accepted password for joeuser from 127.0.0.1 port 52212 ssh2 debug1: monitor_child_preauth: joeuser has been authenticated by privileged process debug1: PAM: establishing credentials User child is on pid 9129 debug1: Entering interactive session for SSH2. debug1: server_init_dispatch_20 debug1: server_input_channel_open: ctype session rchan 0 win 65536 max 16384 debug1: input_session_request debug1: channel 0: new [server-session] debug1: session_new: session 0 debug1: session_open: channel 0 debug1: session_open: session 0: link with channel 0 debug1: server_input_channel_open: confirm session debug1: server_input_global_request: rtype [email protected] want_reply 0 debug1: server_input_channel_req: channel 0 request pty-req reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req pty-req debug1: Allocating pty. debug1: session_new: session 0 debug1: session_pty_req: session 0 alloc /dev/pts/1 debug1: server_input_channel_req: channel 0 request shell reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req shell debug1: Setting controlling tty using TIOCSCTTY. debug1: Received SIGCHLD. debug1: session_by_pid: pid 9130 debug1: session_exit_message: session 0 channel 0 pid 9130 debug1: session_exit_message: release channel 0 debug1: session_by_tty: session 0 tty /dev/pts/1 debug1: session_pty_cleanup: session 0 release /dev/pts/1 Received disconnect from 127.0.0.1: 11: disconnected by user debug1: do_cleanup debug1: do_cleanup debug1: PAM: cleanup debug1: PAM: closing session debug1: PAM: deleting credentials Here you have the full output of sshd -dd, together with ssh -vv. Bash: # bash --version GNU bash, version 3.2.49(1)-release (arm-none-linux-gnueabi) Copyright (C) 2007 Free Software Foundation, Inc. The bash binary was cross compiled from source. I also tried using a pre-compiled binary from the Optware distribution, but had the exact same problem. I checked for missing shared libraries using objdump -x, but they're all there. Any ideas what could be causing this "Permission denied, please try again."? I'm almost diving in the bash source code to investigate, but trying to avoid hours chasing something that may be silly.

  Read the article

• How to disable hiddev96 in linux (or tell it to ignore a specific device)

  - by Miky D

  I'm having problems with a CentOS 5.0 system when using a certain USB device. The problem is that the device advertises itself as a HID device and linux is happy to try to provide support for it: In /ver/log/messages I see a line that reads: hiddev96: USB HID 1.11 Device [KXX USB PRO] on usb-0000:00:1d.0-1 My question comes down to: Is there a way to tell linux to not use hiddev96 for that device in particular? If yes, how? If not, what are my options - can I turn hiddev96 off completely? UPDATE I should probably have been a bit more specific about what is going on. The machine is running Centos 5.0, and on top of it I'm running VMWare workstation with Windows XP - which is where the USB device is actually supposed to operate. All works fine for other USB devices (i.e. VMWare successfully connects the USB device to the guest OS and the OS can use it, but for this particular device VMWare connects it to the guest OS, but the OS can't read/write to it) Every attempt locks up the application that is trying to communicate with the device. I've reason to believe that it is because the device is a HID device and there's some contention between the Linux host and the Windows guest OS in accessing the device. Below is the output from modprobe -l|grep -i hid as requested by @Karolis: # modprobe -l | grep -i hid /lib/modules/2.6.18-53.1.14.el5/kernel/net/bluetooth/hidp/hidp.ko /lib/modules/2.6.18-53.1.14.el5/kernel/drivers/usb/misc/phidgetservo.ko /lib/modules/2.6.18-53.1.14.el5/kernel/drivers/usb/misc/phidgetkit.ko And here is the output of lsmod # lsmod Module Size Used by udf 76997 1 vboxdrv 65696 0 autofs4 24517 2 hidp 23105 2 rfcomm 42457 0 l2cap 29633 10 hidp,rfcomm tun 14657 0 vmnet 49980 16 vmblock 20512 3 vmmon 945236 0 sunrpc 144253 1 cpufreq_ondemand 10573 1 video 19269 0 sbs 18533 0 backlight 10049 0 i2c_ec 9025 1 sbs button 10705 0 battery 13637 0 asus_acpi 19289 0 ac 9157 0 ipv6 251393 27 lp 15849 0 snd_hda_intel 24025 2 snd_hda_codec 202689 1 snd_hda_intel snd_seq_dummy 7877 0 snd_seq_oss 32577 0 nvidia 7824032 31 snd_seq_midi_event 11073 1 snd_seq_oss snd_seq 49713 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 11725 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 42945 0 snd_mixer_oss 19009 1 snd_pcm_oss snd_pcm 72133 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss joydev 13313 0 sg 36061 0 parport_pc 29157 1 snd_timer 24645 2 snd_seq,snd_pcm snd 52421 13 snd_hda_intel,snd_hda_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer ndiswrapper 170384 0 parport 37513 2 lp,parport_pc hci_usb 20317 2 ide_cd 40033 1 tg3 104389 0 i2c_i801 11469 0 bluetooth 53925 8 hidp,rfcomm,l2cap,hci_usb soundcore 11553 1 snd cdrom 36705 1 ide_cd serio_raw 10693 0 snd_page_alloc 14281 2 snd_hda_intel,snd_pcm i2c_core 23745 3 i2c_ec,nvidia,i2c_i801 pcspkr 7105 0 dm_snapshot 20709 0 dm_zero 6209 0 dm_mirror 28741 0 dm_mod 58201 8 dm_snapshot,dm_zero,dm_mirror ahci 23621 4 libata 115833 1 ahci sd_mod 24897 5 scsi_mod 132685 3 sg,libata,sd_mod ext3 123337 3 jbd 56553 1 ext3 ehci_hcd 32973 0 ohci_hcd 23261 0 uhci_hcd 25421 0

  Read the article

• Any reason not to disable the Windows pagefile given enough physical RAM?

  - by Evgeny

  The question of disabling the Windows pagefile has already been discussed quite a bit, for example here and here and here. People continue to upvote answers that say "you should not disable your pagefile even if you have plenty of RAM", but I have yet to see any concrete, verifiable reasons being given for this advice. As far as I can see, if you never need to read from the pagefile (because you have enough RAM) then performance could only be worse with it enabled due to Windows pre-emptively writing to it. At best, performance would be the same. I can't see how it could possibly be improved by writing data you never need to read. So my question is: Assuming that I have enough physical RAM for everything I do, is there any reason I should not disable the pagefile? Let's say the version of Windows is Windows XP x64 SP2 or Windows Server 2003 x64 SP2 (same thing). If it's different for Windows Server 2008 x64 I'd be interested to hear an answer for that as well. I'm looking for specific, objective reasons from good sources, not just opinions. Something like "here are the benchmarks done with and without a pagefile and the results were better with a pagefile, even with enough RAM" or "according to this MS KB article problem X occurs if you disable the pagefile". So far the only reasons I've seen mentioned are: Even if you think you have enough RAM you might run out. OK, but for the purposes of this question, let's just take it as a given that I have enough. Maybe I only ever read my email and I have 16GB RAM. Or 128GB. Or 1TB. Or whatever - but it's enough for 100% of what I do, 100% of the time. Another way to think of it is: if I have x MB physical RAM and y MB pagefile and I never run out of RAM in that configuration, would I not be better off, performance-wise, with x+y MB physical RAM and no pagefile? Windows is "used to" having a paging file and it might not function as reliably (from Understanding the Impact of RAM on Overall System Performance That's rather vague and I find it hard to believe, given that MS has provided the option to disable the pagefile. Windows knows what it's doing better than you. No - it doesn't know that I won't run more programs or load more data, but I do.

  Read the article

• Reproducible file corruption for files on windows share

  - by bbuser

  We have about 40 file servers in our intranet to distribute software packages. The servers have names like example01, example02 etc. Every name resolves to a single IP-address (A-record) and the IP resolves back to that name (PTR) for every single server. The thing is, that for a certain file (mypackage.cab) I get different results depending on whether I use: \\192.0.2.01\fs\pkg\X12345678 or \\example01.foo\fs\pkg\X12345678 While in one case the file is correct in the other case the file has exactly the right size, but it is all zeros. For a certain combination of client and server I can reproduce this reliably. It doesn´t matter if I download in Windows Explorer, via robocopy or even from Linux with smbclient. It´s always the same, one file corrupt, the other ok. It happens only for certain combinations of clients and servers, not others. For example: client01 example01.foo -> OK (192.0.2.01 is also OK) client01 example02.foo -> broken (but 192.0.2.02 is OK) client02 example01.foo -> broken (but 192.0.2.01 is OK) client02 example02.foo -> OK (192.0.2.02 is also OK) client03 example06.foo -> OK (but 192.0.2.06 is broken) client03 example07.foo -> OK (192.0.2.07 is also OK) etc... In some cases I get the broken file when I use the IP address in other cases when I use the name. For every client the majority of servers is Ok, but from every client I tested I have at least 4 cases of broken files. All this happens only for mypackage.cab (about 5k in size), it never happened for any of the other files in the same directory. Confused? Certainly I am. Any idea what can cause this or any idea what to try to figure it out is welcome. Clients are Windows XP. Servers are NetApp filers I don´t have access to. I can (and will) contact the filer team again, but first I have to have an idea what is going on.

  Read the article

• Reproducible file corruption for files on windows share

  - by bbuser

  We have about 40 file servers in our intranet to distribute software packages. The servers have names like example01, example02 etc. Every name resolves to a single IP-address (A-record) and the IP resolves back to that name (PTR) for every single server. The thing is, that for a certain file (mypackage.cab) I get different results depending on whether I use: \\192.0.2.01\fs\pkg\X12345678 or \\example01.foo\fs\pkg\X12345678 While in one case the file is correct in the other case the file has exactly the right size, but it is all zeros. For a certain combination of client and server I can reproduce this reliably. It doesn´t matter if I download in Windows Explorer, via robocopy or even from Linux with smbclient. It´s always the same, one file corrupt, the other ok. It happens only for certain combinations of clients and servers, not others. For example: client01 example01.foo -> OK (192.0.2.01 is also OK) client01 example02.foo -> broken (but 192.0.2.02 is OK) client02 example01.foo -> broken (but 192.0.2.01 is OK) client02 example02.foo -> OK (192.0.2.02 is also OK) client03 example06.foo -> OK (but 192.0.2.06 is broken) client03 example07.foo -> OK (192.0.2.07 is also OK) etc... In some cases I get the broken file when I use the IP address in other cases when I use the name. For every client the majority of servers is Ok, but from every client I tested I have at least 4 cases of broken files. All this happens only for mypackage.cab (about 5k in size), it never happened for any of the other files in the same directory. Confused? Certainly I am. Any idea what can cause this or any idea what to try to figure it out is welcome. Clients are Windows XP. Servers are NetApp filers I don´t have access to. I can (and will) contact the filer team again, but first I have to have an idea what is going on.

  Read the article

• SSH as root using public key still prompts for password on RHEL 6.1

  - by Dean Schulze

  I've generated rsa keys with cygwin ssh-keygen and copied them to the server with ssh-copy-id -i id_rsa.pub [email protected] I've got the following settings in my /etc/ssh/sshd_config file RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys PermitRootLogin yes When I ssh [email protected] it still prompts for a password. The output below from /usr/sbin/sshd -d says that a matching keys was found in the .ssh/authorized_keys file, but it still requires a password from the client. I've read a bunch of web postings about permissions on files and directories, but nothing works. Is it possible to ssh with keys in RHEL 6.1 or is this forbidden? The debug output from ssh and sshd is below. $ ssh -v [email protected] OpenSSH_6.1p1, OpenSSL 1.0.1c 10 May 2012 debug1: Connecting to my.ip.address [my.ip.address] port 22. debug1: Connection established. debug1: identity file /home/dschulze/.ssh/id_rsa type 1 debug1: identity file /home/dschulze/.ssh/id_rsa-cert type -1 debug1: identity file /home/dschulze/.ssh/id_dsa type 2 debug1: identity file /home/dschulze/.ssh/id_dsa-cert type -1 debug1: identity file /home/dschulze/.ssh/id_ecdsa type -1 debug1: identity file /home/dschulze/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH_5* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 9f:00:e0:1e:a2:cd:05:53:c8:21:d5:69:25:80:39:92 debug1: Host 'my.ip.address' is known and matches the RSA host key. debug1: Found key in /home/dschulze/.ssh/known_hosts:3 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/dschulze/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Offering DSA public key: /home/dschulze/.ssh/id_dsa debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Trying private key: /home/dschulze/.ssh/id_ecdsa debug1: Next authentication method: password Here is the server output from /usr/sbin/sshd -d [root@ga2-lab .ssh]# /usr/sbin/sshd -d debug1: sshd version OpenSSH_5.3p1 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: rexec_argv[0]='/usr/sbin/sshd' debug1: rexec_argv[1]='-d' debug1: Bind to port 22 on 0.0.0.0. Server listening on 0.0.0.0 port 22. debug1: Bind to port 22 on ::. Server listening on :: port 22. debug1: Server will not fork when running in debugging mode. debug1: rexec start in 5 out 5 newsock 5 pipe -1 sock 8 debug1: inetd sockets after dupping: 3, 3 Connection from 172.60.254.24 port 53401 debug1: Client protocol version 2.0; client software version OpenSSH_6.1 debug1: match: OpenSSH_6.1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: permanently_set_uid: 74/74 debug1: list_hostkey_types: ssh-rsa,ssh-dss debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: client->server aes128-ctr hmac-md5 none debug1: kex: server->client aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST received debug1: SSH2_MSG_KEX_DH_GEX_GROUP sent debug1: expecting SSH2_MSG_KEX_DH_GEX_INIT debug1: SSH2_MSG_KEX_DH_GEX_REPLY sent debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: KEX done debug1: userauth-request for user root service ssh-connection method none debug1: attempt 0 failures 0 debug1: PAM: initializing for "root" debug1: userauth-request for user root service ssh-connection method publickey debug1: attempt 1 failures 0 debug1: test whether pkalg/pkblob are acceptable debug1: PAM: setting PAM_RHOST to "172.60.254.24" debug1: PAM: setting PAM_TTY to "ssh" debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: trying public key file /root/.ssh/authorized_keys debug1: fd 4 clearing O_NONBLOCK debug1: matching key found: file /root/.ssh/authorized_keys, line 1 Found matching RSA key: db:b3:b9:b1:c9:df:6d:e1:03:5b:57:d3:d9:c4:4e:5c debug1: restore_uid: 0/0 Postponed publickey for root from 172.60.254.24 port 53401 ssh2 debug1: userauth-request for user root service ssh-connection method publickey debug1: attempt 2 failures 0 debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: trying public key file /root/.ssh/authorized_keys debug1: fd 4 clearing O_NONBLOCK debug1: matching key found: file /root/.ssh/authorized_keys, line 1 Found matching RSA key: db:b3:b9:b1:c9:df:6d:e1:03:5b:57:d3:d9:c4:4e:5c debug1: restore_uid: 0/0 debug1: ssh_rsa_verify: signature correct debug1: do_pam_account: called Accepted publickey for root from 172.60.254.24 port 53401 ssh2 debug1: monitor_child_preauth: root has been authenticated by privileged process debug1: temporarily_use_uid: 0/0 (e=0/0) debug1: ssh_gssapi_storecreds: Not a GSSAPI mechanism debug1: restore_uid: 0/0 debug1: SELinux support enabled debug1: PAM: establishing credentials PAM: pam_open_session(): Authentication failure debug1: Entering interactive session for SSH2. debug1: server_init_dispatch_20 debug1: server_input_channel_open: ctype session rchan 0 win 1048576 max 16384 debug1: input_session_request debug1: channel 0: new [server-session] debug1: session_new: session 0 debug1: session_open: channel 0 debug1: session_open: session 0: link with channel 0 debug1: server_input_channel_open: confirm session debug1: server_input_global_request: rtype [email protected] want_reply 0 debug1: server_input_channel_req: channel 0 request pty-req reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req pty-req debug1: Allocating pty. debug1: session_pty_req: session 0 alloc /dev/pts/1 ssh_selinux_setup_pty: security_compute_relabel: Invalid argument debug1: server_input_channel_req: channel 0 request shell reply 1 debug1: session_by_channel: session 0 channel 0 debug1: session_input_channel_req: session 0 req shell debug1: Setting controlling tty using TIOCSCTTY. debug1: Received SIGCHLD. debug1: session_by_pid: pid 17323 debug1: session_exit_message: session 0 channel 0 pid 17323 debug1: session_exit_message: release channel 0 debug1: session_pty_cleanup: session 0 release /dev/pts/1 debug1: session_by_channel: session 0 channel 0 debug1: session_close_by_channel: channel 0 child 0 debug1: session_close: session 0 pid 0 debug1: channel 0: free: server-session, nchannels 1 Received disconnect from 172.60.254.24: 11: disconnected by user debug1: do_cleanup debug1: PAM: cleanup debug1: PAM: deleting credentials

  Read the article

• Looking for a Software to harden Windows machines

  - by MosheH

  I'm a network administrator of a small/medium network. I'm looking for a software (Free or Not) which can harden Windows Computers (XP And Win7) for the propose of hardening standalone desktop computers (not in domain network). Note: The computers are completely isolated (standalone), so i can't use active directory group policy. moreover, there are too many restriction that i need to apply, so it is not particle to set it up manual (one by one). Basically what I’m looking for is a software that can restrict and disable access for specific user accounts on the system. For Example: User john can only open one application and nothing else -- He don’t see no icon on the desktop or start menu, except for one or two applications which i want to allow. He can't Right click on the desktop, the task-bar icons are not shown, there is no folder options, etc... User marry can open a specific application and copy data to one folder on D drive. User Dan, have access to all drives but cannot install software, and so on... So far ,I've found only the following solutions, but they all seems to miss one or more feature: Desktop restriction Software 1. Faronics WINSelect The application seems to answer most of our needs except one feature which is very important to us but seems to be missing from WINSelect, which is "restriction per profile". WINSelect only allow to set up restrictions which are applied system-wide. If I have multiple user accounts on the system and want to apply different restrictions for each user, I cant. Deskman (No Restriction per user)- Same thing, no restriction per profile. Desktop Security Rx - not relevant, No Win7 Support. The only software that I've found which is offering a restriction per profile is " 1st Security Agent ". but its GUI is very complicated and not very intuitive. It's worth to mention that I'm not looking for "Internet Kiosk software" although they share some features with the one I need. All I need is a software (like http://www.faronics.com/standard/winselect/) that is offering a way to restrict Windows user interface. So IF anybody know an Hardening software which allows to set-up user restrictions on Windows systems, It will be a big, big, big help for me! Thanks to you all

  Read the article

• Outlook refuses to connect to Exchange

  - by wfaulk

  Outlook 2007 under Windows XP connecting to Exchange 2003 SP2: when started, it flips back and forth between "Connecting to Exchange Server" and "Disconnected" three or four times, then gives up and stays disconnected. I tried deleting the ost file (which was nearly 2GB), turning Cached mode on and off, recreating the account inside the Mail control panel, changing the account to use HTTP, and probably some other things. None of it seemed to make any difference, until … After fiddling with it for a while, I got this absurd error message dialog at startup, and it exits after I click OK: Cannot start Microsoft Office Outlook. Cannot open the Outlook window. The set of folders cannot be opened. Microsoft Exchange is not available. Either there are network problems or the Exchange server is down for maintenance. (I'm not sure if I can even trust that message. It's so long, it just feels like a random offset into Outlook's stack of error messages.) Either way, the Exchange server is available to everyone else, and is available via OWA from that computer. I ran Process Explorer against Outlook and it showed 5 or so ESTABLISHED connections to our Exchange server, plus listening on two UDP ports, and two CLOSE_WAIT connections to localhost. If I managed to look at Outlook's IP connections while it was doing its Connecting/Disconnected dance, it had a huge number of connections open to the Exchange server. It more than filled ProcExp's dialog box; I'm guessing at least 20, probably more. The only other odd thing is that our network admin at some point added a wildcard DNS record to the domain name that we use for email, and now Outlook will sometimes (always?) start by complaining about autodiscover.example.com's SSL certificate. There is a web server there, but it doesn't have any sort of email autodiscover anything on it. It doesn't make any difference if I click "OK" or "Cancel" (or whatever the buttons are). I also added a bogus entry for the hostname to Windows' hosts file, pointing it at 127.0.0.2, and it stopped complaining about the certificate. (The CLOSE_WAIT sockets above were from before I made this change, and went away after.) I don't think this is related, as the same problem should exist for everyone, but it might be. This is the second time this user has had this problem. The first time, I never found a solution other than reinstalling Outlook. Now that it's a pattern, I'd like to find a permanent solution, rather than assume it's a random glitch.

  Read the article

• Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

  - by Software Monkey

  I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

  Read the article

< Previous Page | 443 444 445 446 447 448 449 450 451 452 453 454  | Next Page >