Search Results

Search found 3590 results on 144 pages for 'ben guest'.

Page 45/144 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• How can I do a virus check on a USB thumb drive using VirtualBox?

  - by ProfKaos

  My copies of Norton and AVG anti-virus won't install on my Server 2008 R2 machine, so I have set up an XP guest on Virtual Box. I'd like to installone of these on the XP machine to check a thumb drive for viruses. How do I set things up so that I'm confident my host machine is safe, and that only the guest machine 'reacts' to the thumb drive?

  Read the article

• Controling virtualbox internet access?

  - by HandyGandy

  Host: Linux/Debian/Ubuntu/Mint ( Helena/karmic koala ) Guest: XP SP2 and SP3 Problem: Relatively new copy of XP migrated to vbox-virus free. To detect biral infection it is desired that internet access is limited. Network access to the host is desired, but access to the internet should be limited to a select few sites. The added overhead of network access should be small when the guest vbox is running, 0 when it is not.

  Read the article

• Automatically mounting windows share in Fedora 12

  - by user15865

  Hi, I'm trying to automatically mount a windows share in a Fedora 12 instance (FC12). When I manually mount things work: mount -t cifs //nas01/servers -o username=guest,password=myPassword /mnt/nas01/servers If I update /etc/fstab with the following: //nas01/servers /mnt/nas01/servers cifs username=guest,password=myPassword 0 0 Nothing happens after reboot. The thing that has me baffled is after a reboot if I run: mount -a The share is mounted. Any ideas on this? Thank you, Martin

  Read the article

• Virtualbox alert on screen changes

  - by rush

  I'm using Debian GNU/Linux + awesome. Inside it I use virtualbox with ms windows. Most time I spend in Linux, however I constantly need to monitor if something new happens in the guest system. Is there any way to make virtualbox alerting about any changes on guest screen (clock is disabled, therefore only new mail or instant message may change the screen)? PS. Unfortunately I can't to move mail and instant messages from windows due to specific clients for only internal network.

  Read the article

• Would we be able to find out what VMs the parent server is using?

  - by jpartogi

  Hi all, I am asking a rather ridiculous question here. Is there any way we can find out from the guest OS the parent OS and the VMs it is using? If it is possible, what command do we invoke from the guest OS? Thanks for your help

  Read the article

• HVM virtualization with PV drivers on XenServer

  - by Nathan

  Is it possible to create an HVM guest in XenServer 5.5 that uses PV drivers for disk and network without being fully paravirutalized? This should give me decent performance from the VM without having to jump through hoops to create a PV guest when a pre-built template doesn't exist. Since PV drivers exist for Windows, and XenServer provides templates for windows that use HVM virtualization this must be possible, I just don't see how to configure this myself.

  Read the article

• How are virtual machine integration packages implemented? [duplicate]

  - by gparyani

  This question already has an answer here: What happen if I install VirtualBox Guest Additions on a host? 1 answer If I install a virtual machine additions package on a virtual machine, (e.g. Virtual Machine Additions for Microsoft Virtual PC 2007, Integration Components on Windows Virtual PC, and Guest Additions on Oracle VM VirtualBox), what happens in the backend on the virtual machine when I enable integration features like mouse pointer integration, window resizing, and folder sharing? In other words, how is it internally implemented?

  Read the article

• Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

  - by Sise

  Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

  Read the article

• VMware server 2.0 SYN/ACK repeating issues

  - by user65579

  VMWare Server 2.0.0 Build 122956 I am having some issues with connecting into a guest VM (Ubuntu linux 4.4.3-4 lucid) running under VMware 2.0 on a windows server host. All connections to and from the VM's work fine, except for FTP. I thought the issue was the FTP daemon at first but it has been ruled out that it is not the daemon or the server itself. When you try to connect to the FTP server from outside of the host OS it fails with a "421 Service not available" but when you try and connect from the local VM or from the host OS the connection goes through fine. I have ran many packet sniffs using wireshark/tcpdump from the VM, the host OS, and the client connecting, the most informative is the host OS. I have attached a PNG of the relavant packets that were captured. I viewed some other network traffic that was sniffed (WWW specifically) and it seems to do the same syn/ack repeating but the user doesnt see any issues. I have disabled the firewall and the issues persisits, I have tried with specific allow rules to ensure the data is allowed and no changes. It appears like VMware attempts to do the ICMP redirect and it works, but then it vmware repeats the packets sent so you get 3 syn/ack's for every one syn from the client. Also VMWare appears to be attempting to establish an FTP connection between the HOST OS and the GUEST OS, because I see the second SYN sent from the HOST OS to the GUEST to initiate a new connection, and it get the appropriate SYN/ACK followed by an ACK, but the client never sees any of this from its end. EG. syn from client syn/ack from host OS to client syn/ack from guest OS to client syn/ack from host OS to client The same thing happens when the connection reset is attempted, RST's start being sent and repeated, the server responds with a valid header to continue the FTP handshake but the RST acknowledgement is allready issued and things are closed. I am not 100% if this is a bug in VMware or possibly a VMNetwork missconfiguration. Does anyone have any thoughts on where exactly the issue could be, things to try to verify or rule out? I have linked to a picture of the relevant packets sniffed from the host OS. http://img18.imageshack.us/img18/7789/vmwareftpconnection.jpg

  Read the article

• Any way to recover ext4 filesystems from a deleted LVM logical volume?

  - by Vegar Nilsen

  The other day I had a proper brain fart moment while expanding a disk on a Linux guest under Vmware. I stretched the Vmware disk file to the desired size and then I did what I usually do on Linux guests without LVM: I deleted the LVM partition and recreated it, starting in the same spot as the old one, but extended to the new size of the disk. (Which will be followed by fsck and resize2fs.) And then I realized that LVM doesn't behave the same way as ext2/3/4 on raw partitions... After restoring the Linux guest from the most recent backup (taken only five hours earlier, luckily) I'm now curious on how I could have recovered from the following scenario. It's after all virtually guaranteed that I'll be a dumb ass in the future as well. Virtual Linux guest with one disk, partitioned into one /boot (primary) partition (/dev/sda1) of 256MB, and the rest in a logical, extended partition (/dev/sda5). /dev/sda5 is then setup as a physical volume with pvcreate, and one volume group (vgroup00) created on top of it with the usual vgcreate command. vgroup00 is then split into two logical volumes root and swap, which are used for / and swap, logically. / is an ext4 file system. Since I had backups of the broken guest I was able to recreate the volume group with vgcfgrestore from the backup LVM setup found under /etc/lvm/backup, with the same UUID for the physical volume and all that. After running this I had two logical volumes with the same size as earlier, with 4GB free space where I had stretched the disk. However, when I tried to run "fsck /dev/mapper/vgroup00-root" it complained about a broken superblock. I tried to locate backup superblocks by running "mke2fs -n /dev/mapper/vgroup00-root" but none of those worked either. Then I tried to run TestDisk but when I asked it to find superblocks it only gave an error about not being able to open the file system due to a broken file system. So, with the default allocation policy for LVM2 in Ubuntu Server 10.04 64-bit, is it possible that the logical volumes are allocated from the end of the volume group? That would definitely explain why the restored logical volumes didn't contain the expected data. Could I have recovered by recreating /dev/sda5 with exactly the same size and disk position as earlier? Are there any other tools I could have used to find and recover the file system? (And clearly, the question is not whether or not I should have done this in a different way from the start, I know that. This is a question about what to do when shit has already hit the fan.)

  Read the article

• Sharing printer form win 7 to xp in virtualbox

  - by Null

  Using virtualbox (win7 host, winXP guest) and a bluetooth printer (a portable one) I've set up printer sharing on host and can print from guest. But when the host isn't connected to the internet printing stops working. I'm using bridged adapter in virtualbox.

  Read the article

• ZFS recordsize for VirtualBox and other virtual disks

  - by JOTN

  Has anyone run across any good benchmarks or other research on tuning the ZFS recordsize when putting virtual disk files on it for a guest OS? I'm using VirtualBox at the moment. I have notice significant performance improvement when working with a DBMS by setting the ZFS recordsize to the same as the DB blocksize, so I'm guessing matching the blocksize of the guest filesystem would also be a good idea.

  Read the article

• How to start VirtualBox using commandline?

  - by Murat Arpat

  I've VirtualBox on a Windows 7 PC and created a virtual machine for Windows XP. Here is what I want to do: Run VirtualBox Power on guest OS (named "Windows XP") Open Winword in guest OS I want to accomplish these 3 steps at once (by using a batch file for example). Any help would be appreciated. In fact I've a batch file but it does not work as I wanted: "C:\Program Files\Oracle\VirtualBox\Vboxmanage.exe" startvm "Windows XP" TIMEOUT 30 "C:\Program Files\Oracle\VirtualBox\VBoxmanage.exe" guestcontrol "Windows XP" execute --image "C:\PROGRA~1\MICROS~2\OFFICE11\WINWORD.EXE" --username xpuser

  Read the article

• Virtual Box, full screen ?

  - by Arkapravo

  Hi How can I get Virtual Box go full screen, as of now I am getting my guest OS in a small screen (640 x 480) type, even 'going full screen' doesn't make any difference ? I want my guest OS to be of same screen size as my host OS ! Regards

  Read the article

• How to use USB Key in Xen 5.6 Environment?

  - by Az

  I am looking for a way to use USB key on a guest OS running on a 5.6 Xen Server environment. The catch is that I need to actually detect in the Guest OS (Win2003 Server) like an actual USB Key. Attaching it as a storage drive doesnt work (It is a key with special attributes that servers as a licensing mechanism). Just wondering if anyone has had a similar need and found a good solution? Thanks, Nate

  Read the article

• Samba deny host not blocking that host

  - by datadevil

  I want to block access to some Samba shares from a certain machine, but somehow I can't get it to work: the machine can still access the shares, and I did restart and reload the samba daemon. Here is a part of my configuration: security = share hosts allow = 127.0.0.1 192.168.1.0/24 interfaces = 127.0.0.1 eth1 192.168.1.2 bind interfaces only = yes hosts deny = 192.168.1.251 encrypt passwords = yes guest ok = yes The shares themselves look like this: [examples] comment = Example path = /foo/bar read only = No guest ok = yes What am I doing wrong here?

  Read the article

• Adding new virtual disks to a Windows host in ESX “live”

  - by warren

  Building on my previous question about RHEL, how do you add get the guest OS to recognize that you've added new drives to it without a reboot? I have Windows 2003, XP, and 2008 guests running on ESX 4. I've added new virtual disks to the VM, but have not figured-out how to get the guest to recognize them without a reboot. Is this possible? If so, how?

  Read the article

• VirtualBox without X server

  - by nccc

  I want to run a guest operating system under a Linux host with VirtualBox, but I don't want to run from within X. I don't want a headless configuration, I don't want to run VirtualBox in the background, I don't want any remote protocols. I just want the guest OS to take control of my console (keyboard, mouse and monitor) and render to the framebuffer directly, not from within an X window. Is this possible?

  Read the article

• How can I tell programatically whether or not the host that a script is running on is a VirtualBox V

  - by Joe Casadonte

  Is there any way to tell if the host that a script is running on is a VirtualBox guest VM? Ideally I'm looking for a cross-platform way. I would think this is next to impossible unless, maybe, something in the Guest Additions provides this. Thanks!

  Read the article

• CentOS 5: Can't access webserver via http from host OS?

  - by adred

  My server is installed on a guest OS on vmware. It really bugs me because I can't access it from the host OS's browser even though there is no discrepancy between /etc/hosts, /etc/sysconfig/network, httpd.conf files. Issuing ifconfig command also returns the same IP. I have also enabled netwroking in the vmware settings. And I can ping the guest OS's IP from the host. Any insights pls???

  Read the article

• Saving Blob data from SQLite database to a file

  - by Felipe

  Hello, I'm trying to save blob data from a SQLite database (Safari cache: Cache.db) to a file, but for some reason sqlite won't read the whole blob. I eventually would like to do this in ruby, but for now something that works directly in sqlite command prompt is fine. Also, I've read all of the entries that talk about this here on stackoverflow, but most of them only discuss the performance of saving images in blobs and the one entry that does show to save blobs to file is in C# which does not help me. Here is what I've tried: sqlite select * from cfurl_cache_response limit 1; 3501|0|945281827|0|http://www.gospelz.com/components/com_jomcomment/smilies/guest.gif|2010-02-24 16:20:07 sqlite select receiver_data from cfurl_cache_blob_data where entry_ID = 3501; GIF89a( A hexdump of the original (guest.gif) file shows that sqlite stops reading the blob after the first null value: $ hexdump -C guest.gif 00000000 47 49 46 38 39 61 28 00 28 00 f7 00 00 f1 f5 fd |GIF89a(.(.......| sqlite .output test.gif sqlite select receiver_data from cfurl_cache_blob_data where entry_ID = 3501; $ hexdump -C test.gif 00000000 47 49 46 38 39 61 28 0a |GIF89a(.|

  Read the article

• backbone.js Model.get() returns undefined, scope using coffeescript + coffee toaster?

  - by benipsen

  I'm writing an app using coffeescript with coffee toaster (an awesome NPM module for stitching) that builds my app.js file. Lots of my application classes and templates require info about the current user so I have an instance of class User (extends Backbone.Model) stored as a property of my main Application class (extends Backbone.Router). As part of the initialization routine I grab the user from the server (which takes care of authentication, roles, account switching etc.). Here's that coffeescript: @user = new models.User @user.fetch() console.log(@user) console.log(@user.get('email')) The first logging statement outputs the correct Backbone.Model attributes object in the console just as it should: User _changing: false _escapedAttributes: Object _pending: Object _previousAttributes: Object _silent: Object attributes: Object account: Object created_on: "1983-12-13 00:00:00" email: "[email protected]" icon: "0" id: "1" last_login: "2012-06-07 02:31:38" name: "Ben Ipsen" roles: Object __proto__: Object changed: Object cid: "c0" id: "1" __proto__: ctor app.js:228 However, the second returns undefined despite the model attributes clearly being there in the console when logged. And just to make things even more interesting, typing "window.app.user.get('email')" into the console manually returns the expected value of "[email protected]"... ? Just for reference, here's how the initialize method compiles into my app.js file: Application.prototype.initialize = function() { var isMobile; isMobile = navigator.userAgent.match(/(iPhone|iPod|iPad|Android|BlackBerry)/); this.helpers = new views.DOMHelpers().initialize().setup_viewport(isMobile); this.user = new models.User(); this.user.fetch(); console.log(this.user); console.log(this.user.get('email')); return this; }; I initialize the Application controller in my static HTML like so: jQuery(document).ready(function(){ window.app = new controllers.Application(); }); Suggestions please and thank you!

  Read the article

• Updating Linking Tables

  - by Sasha

  I've currently adding a bit of functionality that manages holiday lettings on top of a CMS that runs on PHP and MySQL. The CMS stores the property details on a couple of tables, and I'm adding a third table (letting_times) that will contain information about when people are staying at the property. Basic functionality would allow the user to add new times when a guest is staying, edit the times that the guest is staying and remove the booking if the guest no longer wants to stay at the property. Right now the best way that I can think of updating the times that the property is occupied is to delete all the times contained in the letting_times database and reinsert them again. The only other way that I can think to do this would be to include the table's primary key and do an update if that is present and has a value, otherwise do an insert, but this would not delete rows of data if they are removed. Is there a better way of doing this?

  Read the article

• In a virtual machine monitor such as VMware's ESXi Server, how are shadow page tables implemented?

  - by ali01

  My understanding is that VMMs such as VMware's ESXi Server maintain shadow page tables to map virtual page addresses of guest operating systems directly to machine (hardware) addresses. I've been told that shadow page tables are then used directly by the processor's paging hardware to allow memory access in the VM to execute without translation overhead. I would like to understand a bit more about how the shadow page table mechanism works in a VMM. Is my high level understanding above correct? What kind of data structures are used in the implementation of shadow page tables? What is the flow of control from the guest operating system all the way to the hardware? How are memory access translations made for a guest operating system before its shadow page table is populated? How is page sharing supported? Short of straight up reading the source code of an open source VMM, what resources can I look into to learn more about hardware virtualization?

  Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >