Search Results

Search found 13434 results on 538 pages for 'boot on power up'.

Page 45/538 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

• No SATA drives after PSU Upgrade

  - by hauptbenutzer

  I know this sounds a lot like this but I just confirmed that my MBR is fine as well as the SSD drive in question. What happened: I upgraded my be-quiet 700w PSU to the 1000w dark power pro. When I tried booting the system and none of the drives (all SATA) were detected, resulting in the "Boot device failure" error. After that I unplugged all but the boot drive, triple checked that all cables were in fact nice and tight inside their sockets, replaced both e-SATA and power cables ; still with the same outcome. Finally I reconnected my old PSU and sure enough the PC booted without any hassle (except of course for the direful construction that is currently occupying my desk). Does anybody have any advice on how to proceed? Surely, it is possible the PSU is faulty but are there other explanations? Thanks in advance PS. if of any help: Motherboard is GIGABYTE GA-PH67A-UD3-B3 H67 LGA 1155

  Read the article

• How can I calculate power consumption of my PC in Watt?

  - by Jitendra vyas

  How can I calculate power consumption of my PC in Watt, to prove my House owner ( I live on rent) , my PC doesn't consume much power? He blames me for Huge power bills even he too use Fridge, A.C. etc and his son watch the TV all the time. We both share one Power meter so for bill we pay 50%-50% but He is saying I use PC all the time even night i keep on for downloading. I just want to calculate power consumption of my PC then will calculate monthly expense of unit as per my City's per unit price for power. I've Windows: Microsoft Windows XP Professional 5.1.2600 Service Pack 3 Memory (RAM): 960 MB CPU Info: AMD Sempron(tm) Processor 2500+ CPU Speed: 1399.0 MHz Sound card: Vinyl AC'97 Audio (WAVE) Display Adapters: VIA/S3G UniChrome Pro IGP | NetMeeting driver | RDPDD Chained DD Monitors: 1 - 17inch LCD - LG Screen Resolution: 1280 X 768 - 32 bit Network: Network Present Network Adapters: Bluetooth Device (Personal Area Network) #2 | WAN (PPP/SLIP) Interface CD / DVD Drives: I: ELBY CLONEDRIVE COM Ports: COM1 | COM2 | COM7 | COM8 | COM9 | COM10 LPT Ports: LPT1 Mouse: 3 Button Wheel Mouse Present Hard Disks: C: 29.3GB | D: 29.3GB | E: 97.7GB | F: 97.7GB | G: 211.9GB USB Controllers: 5 host controllers. Firewire (1394): 1 host controllers. Manufacturer: Phoenix Technologies, LTD Product Make: MS-7142 AC Power Status: OnLine BIOS Info: AT/AT COMPATIBLE | 01/18/06 | VIAK8M - 42302e31 Motherboard: MICRO-STAR INTERNATIONAL CO., LTD MS-7142 Modem: ZTE USB Modem FFFE CDMA #2

  Read the article

• How to create a plymouth splash with boot messages, progress bar and a spinning logo?

  - by Vitaly

  I would like to know how to create a splash for my ubuntu mavercik with boot messages being displayed when i boot as well as a progress bar and a spinning logo. or if possible how to edit a splash which already has a spinning logo and a progress bar, and add a boot messages to it. any help appreciated, thanks in advance! http://gnome-look.org/content/show.php/Ubuntu+10.4+and+10.10+Plymouth+Splash?content=128607 this is the theme i wud like to edit and i would like somethn like this or this is the exact splash i want to create.

  Read the article

• How can one unlock a fully encrypted Ubuntu 11.10 system over SSH at boot?

  - by Jeff

  In previous versions of Ubuntu, and current versions of Debian, you can unlock a fully encrypted system (using dmcrypt and LUKS) at boot time over SSH. It was as easy as: Installing the encrypted system using the Ubuntu alternate installer disk or normal Debian installer disk and choosing to encrypt the system. After the system is installed, adding the dropbear and busybox packages. Updating the initram-fs to authorize your ssh key. At boot time, you'd just ssh to the machine, and do: echo -ne "keyphrase" > /lib/cryptsetup/passfifo The machine would then unlock and boot the encrypted system. Using the exact same steps on Ubuntu 11.10, I can ssh to the machine, but /lib/cryptsetup/passfifo doesn't exist. There appears to be no way to unlock the system over ssh. I'm not sure where to look to see if this functionality changed or if it was removed.

  Read the article

• How can I start Busybox at boot time, from GRUB, or even before GRUB?

  - by Andrei

  Most Busybox questions are related to the fact that users are dropped to a Busybox shell due to some unknown issues at boot time. This must make Busybox one of the most hated pieces of software. My problem is the opposite. I want to deliberately start Busybox at boot time either from GRUB, or even before GRUB. Is this possible? How can I do it? The purpose is to execute some commands before the boot sequence is reinitiated. So basically I want to execute some commands to make some hardware available to the bootloader.

  Read the article

• How do I make ESXi 5.0 to shutdown virtual machines when the physical power button is pushed?

  - by Pawel Sawicki

  I have a home NAS/DLNA server built out of an HP Micro Server with the HP branded VMware ESXi 5.0.0 build-623860 (free license) installed. Being a home media center I'd like it to be "manageable" by all my household members. This requires that it needs to be powered on an off (including all the VMs inside) by anybody with the physical access to the server by simply pressing the power button on the chassis. The "startup" part is easy to obtain - all I had to do was to configure the startup/shutdown policy: Once the server powers up, all VMs start as well and that's exactly what I need. Well.. it did work up until 5.0.0U1, but that's a different story: http://blogs.vmware.com/vsphere/2012/03/free-esxi-hypervisor-auto-start-breaks-with-50-update-1.html Unfortunately, pressing the power button doesn't gracefully shutdown the guest machines - they are terminated instead. If I run the "shut down" command from the vSphere Client interface guests are powered off. I'd like to get the same end result when the physical power button is switched. I've poked around a bit on the ESXi server. There's a "/sbin/shutdown.sh" script that seemed to do exactly what I need... but after trying it does exactly what the power off button. The "/etc/inittab" contains an entry for the "shutdown" level but I suppose it's not hooked to the power button. I can't find any acpi related configuration, neither do I know what exactly is executed when the power button is pressed. Does anybody have a clue how can I make the VMs shutdown automatically when the physical power switch is pressed to turn of the computer?

  Read the article

• Mount an external drive at boot time only if it is plugged in.

  - by Jeremy

  I've got an entry for an external harddrive in my fstab: UUID="680C0FE30C0FAAE0" /jgdata ntfs noatime,rw But sometimes this drive isn't plugged in at boot time. This leaves me half way through a boot, with a prompt to "Continue Waiting, press S or press M" but no keypress has any affect at this stage (including ctrl-alt-delete, not even caps-lock). Short of writing a script to check the output of fdisk -l, how can I mount this drive at boot time only if it is present? It would be handy to have an fdisk entry for this drive, so I can just type mount /jgdata instead of needing a device name.

  Read the article

• Why do manufacturers not show all hardware power usage?

  - by Drew

  I find it slightly more difficult to build a computer when I do not know how much power is needed for a component. When selecting a power supply for a computer, it is difficult to know how large of one to get. You don't want to go too large for cost reasons and circuit reasons, but you don't want to go too low and not be able to properly use every component. For instance, a graphics card might say "Minimum of a 500 Watt power supply. (Minimum recommended power supply with +12 Volt current rating of 30 Amps.)" But it really needs 360W (12V * 30A). So why don't they just say "Uses 360W max and xxxW peak"? Processors, I have noticed are good at reporting their power usage, but aside from processors and sometimes graphics cards, power usage is easily found. What is the power consumed by the Blu-ray / DVD drives? By the HDDs/SSDs? By the Mobo? etc. Why are these questions not easily answered when building a machine?

  Read the article

• What steps to take in resolving/fixing/optimizing a long boot, with possible looping errors as the culprit

  - by Tchalvak

  So my boot time has been slowing and slowing as time has gone on... I am running a number of services (e.g. apache/mysql, postgresql), but it has seen a drastic slowing lately, while I've only been applying updates as normal. I happened to check out my /var/log/boot.log and it is spammed with many lines of this: init: upstart-udev-bridge main process (2738) terminated with status 1 init: upstart-udev-bridge main process ended, respawning I wasn't able to find any solutions to that issue in google, or much talk of it at all, and I'm not really certain that error is the problem, but it is the only lead that I have. What steps should I go through to diagnose boot problems/a slow bootup?

  Read the article

• How to get disable nVidia Graphics Card (which has recently expired) so that I can boot Desktop ?

  - by shan23

  I have a 3-4 years old laptop (Compaq V3000), which had Win Vista with Ubuntu 10.10 in dual boot configuration. The graphics card inside is an old Nvidia GeForce Go 7200. One fine day, my graphics card died (of old age, presumably) - resulting in myself being initially unable to boot to WinVista and Ubuntu 10.10. I solved the problem with WinVista (disabled Nvidia card after booting to Safe mode), but I don't know how to do the same with Ubuntu. I can only disable the 3rd-party driver after I boot to desktop, but since its crashing before that, I'm unable to do so. Can anyone help me disable the graphics card in Ubunutu ?

  Read the article

• The boot selection failed because a required device is inaccessible 0xc000000e

  - by bbodenmiller

  A family member of mine recently went on vacation and turned off their computer, something they normally do not do, upon returning home it would not turn on and now returns the error message below. Generally friends and family come to me for help with computers and I have no problem, however this time I am a bit stumped. Any suggestions would be greatly appreciated. As you can see the error message is: Status: 0xc000000e Info: The best selection failed because a required device is inaccessible. Before going to this error message it briefly flashes the Windows loading screen. I have been able to confirm through the Windows RE Command Line and the dir command that the C: drive is accessible and likely is just suffering a bootup issue. I have tried: Launching the repair process discussed in the error message three times however each time it requires a restart and then returns to the same error message. Changing the boot order to be hard drive first Getting into safe mode; F8 just results in the same error message before I can get to the menu to select safe mode I have checked to make sure the BCD (bcdedit, Boot Configuration Data) is still intact as per https://www.symantec.com/business/support/index?page=content&id=TECH160475 I plan to try (but would like additional comments on): sfc /scannow; requires a restart and thus will likely result in the error message again A memory scan Bootrec as per http://support.microsoft.com/kb/927392#method1 Swapping IDE cables/ports Resetting the BIOS I noticed others with similar issues around the web are dual-booting however this machine is not setup in a dual-boot environment. Additionally at one point this error message supposedly showed up before I started working on the computer: The instruction at 0xfbe2584d referenced memory at 0x00000008. The memory could not be read. As previously stated any additional suggestions or words of advice would be greatly apprecaited.

  Read the article

• Can't boot flash drive on GIGABYTE motherboard

  - by Deltik

  Situation When I try to boot from my flash drive, my GIGABYTE 970A-UD3 motherboard returns this: Loading Operating System ... Boot error All other motherboards I've tried support booting from that flash drive (and a backup flash drive). The operating systems I tried on both flash drives were created with usb-creator-gtk (Ubuntu USB Startup Disk Creator). I know that the motherboard understands that there is an operating system on the flash drives because when I erase them, it complains in an ALL CAPS RAGE that there isn't an operating system, which is correct. How can I boot a flash drive that's bootable from other motherboards on this motherboard? Qualification This question is not a duplicate of this one because directly writing to the flash drive as an ISO 9660 (dd if=operating_system.iso of=/dev/sdb) still does not have the motherboard recognize the operating system. This question should be a duplicate of this one because I provide more information not provided by that poster. This forum thread has broken links and does not have a solution to my problem. Nobody knows what's going on in this forum thread.

  Read the article

• Windows 7 Black Screen On Boot, Seperate Bootable VHD Works Fine

  - by David Osborn

  I have a Window 7 x64 install with a bootable VHD (also Windows 7 x64). I was having problems getting my homeserver to do backups (VSS erred) so I ran check disk and used a tool from MS (cleanc2r.exe) to remove an empty Q drive from the VHD that I believe was a result of installing Office 2010 Beta. (All of this was done on the bootable VHD, not the main install.) Now I can't boot into the main install. It gets past the Starting Windows screen and then goes black. I can still boot into the bootable VHD and everything works fine from there. I have tried to boot the main install in Safe Mode/Safe Mode with Networking/and Safe Mode command prompt and it has the same issue. I ran chkdsk /r on the main install and after doing all the work there was a message about correcting some free space that was marked as allocated and also that it was unable to make an entry into the event log. I tried the startup repair utility and it found no problems. I don't see the setting for restore to last know good configuration so I couldn't do that. I don't recall installing anything new to the main install nor having hooked up any new hardware recently.

  Read the article

• Laptop will not boot

  - by WillumMaguire

  This is a dell studio 1558 laptop. Now, something is wrong with the charger that it won't charge the laptop, but the laptop can turn on and operate properly as long as it is attached. It has been like this for a while, but it's not the problem. My problem is that as of yesterday, It takes several minutes to get past the "dell" startup logo (where is says "f2 setup" and "f12 boot options"). After it gets past, it beeps as normal to tell me about the charger and gives me the f2/f12 options and f1 to continue as normal. I can press f12 to get into boot options and load into my live USB BackTrack 5 ISO, but after "startx" it just stays at a black screen. I can also access BIOS setup, but see nothing that would help the problem. When I boot to the HDD, it gives me this Intel UNDI, PXE-2.1 (build 083) Realktek PCIe GBE Family Controller Series V.2.29 (06/30/09) PXE-E61: Media test failure, check cable PXE-M0F: Exiting PXE ROM Operating System not found Also, pressing f8 gives me the same results as booting as normal. It is running Windows 7 Ultimate, dual-core Intel i3 @ 2.27ghz and 4gb RAM. I think there is an issue with the HDD, as the "Operating System not found" would lead me to believe. Is this a fixable problem?

  Read the article

• Windows 8.1 - Won't boot (0xc000000f), bcdedit fails

  - by user3014097

  I’m pretty much stuck at this point. So, backstory: Windows was installed on one of the SSDs currently in my tower. I bought a new SSD to install Windows (8.1 64 bit) on. Windows installation went fine, booted up, and formatted the old SSD from within Windows (this seems to have been a mistake, but I didn’t realize that at the time). Despite formatting the old SSD, whenever I tried to boot I was told that there were 2 Windows installations. Apparently, when I formatted the old drive, not all of the partitions were removed. So, I booted up with the repair utility, went into cmd, and deleted the non-primary partitions on the old SSD (there were 2 – think they were system and recovery, although I’m forgetting now). Reboot – computer won’t boot. Getting the 0xc000000f “The boot selection failed because a required device is inaccessible” error. Troubleshooting so far: Automatic repair doesn’t fix anything (I’ve never had luck with it though) If I go to install a new version of Windows, the drives and partitions are all there. The SSD is functioning, I at least know that. I’ve essentially gone through this guide: https://neosmart.net/wiki/recovering-windows-bootloader/ Unfortunately, I’m not getting anywhere. I’m not even entirely sure how to describe the errors I’m getting, so I’ve just included pictures of every step (I can't actually post them though so I just included a photobucket link). http://s319.photobucket.com/user/DGalt11/library/Computer%20Issue Am I completely screwed here (i.e. reformat and reinstall?)? Thanks

  Read the article

• Boot sequence unlike reboot

  - by samgoody

  When I turn on the computer it acts very differently than when I reboot it. [WinXP Pro, Intel Core2 6600, 2.4GHZ, 2GB RAM, NVIDA GeForce] Boot: Monitor must be plugged into the motherboard or no image. Screen resolution 800x600. Changes to the resolution cause only the top half of the screen to be usable, and are lost when I shut down the computer. Desktop icons arranged in neat rows on left of desktop. Nothing of note in system tray In Device Manger - Display adapter: Intel(R) Q965/Q963 Express Chipset Family In Device Manger - Monitors, two monitors are listed Hibernate and standby work. Reboot: Monitor must be plugged into the graphics card or no image. Screen resolution - 1280x1024 Desktop icons arranged in the cute circle that I put them in. NVIDIA icon shows in system tray. In Device Manger - Display adapter: NVIDA GeForce 6200LE In Device Manger - Monitors, one monitor is listed Hibernate and standby do not work. When awakened after a hibernation it says: The system could not be restarted from its previous location because the restoration image is corrupt. Delete restoration data & proceed to system boot? Double reboot (inconsistent): Monitor must be plugged into the graphics card. Screen resolution - 1024x768 Odd icon shows in system tray whose tooltip says "Intel Graphics" For a while my morning ritual was to boot, wait, reboot using (alt+ctrl+del - ctrl+u - R), wait. Keeping the monitor plugged into the graphics card. But aside for the inefficiency of this method, I sometimes want to standby and can't. On the other hand, the computer is unusable when set to 800x600. Please help, anyone?

  Read the article

• Lost Windows 7 boot after EasyBCD with EFI

  - by drent

  I've got a Lenovo Y580 with a 64GB SSD and a 1TB HDD setup using GPT and setup to boot from (U?)EFI. I was trying to get my Linux Mint installation on the Windows boot manager using EasyBCD (I didn't realise EFI but it wiped my boot partition/loader and I cannot seem to get Windows back (and I still can't get a bootable Linux Mint). Using the System Recovery utility, Startup Repair can't "see" windows (it might be because I'm using a 7 Pro disk to recover Home Premium?). In command prompt, Bootrec tools don't do anything and bootsect can't run because it says that it's for BIOS only and I've booted with EFI. I can see the EFI data on the 200mb SSD partition using diskpart but I don't know how to add Windows back onto whatever bootloader I have/need. At the moment the only options I can see are: Do a fresh install of Windows and hope that the setup remains as fast as the default one (the SSD is some kind of cache for Windows but I can't quite see how it works given that the rest of the SSD is unpartitioned space). This seems like overkill given that Windows was working fine til EasyBCD deleted it. Try forcing BIOS mode and see if that somehow magically fixes things Try converting from GPT to MBR to try and use the bootrec/bootsect tools (and maybe back again) which seems like a really bad idea. Anyone have any ideas?

  Read the article

• After installing Windows 7, I can no longer get to Debian 6 (dual boot)

  - by Jeremy

  I had Debian 6 on my machine (Dell Vostro 260) and used GParted to shrink the partition. I then tried installing Windows 7 on that partition. After Windows 7 installed, I could not choose which OS to run. It would just boot into Windows. I ran GParted again, and saw that Windows created another partition, labeled "System Reserved". That partition had the boot flag set. I tried moving the boot flag to other partitions, including my Debian partition and one with a file system "linux-swap". No option would actually load an OS or anything except for the Windows partition, which is not what I want. Is it worth it to try to fix this installation, or should I start over. I have all my data backed up, so I can easily install from scratch if I need to. If I do start from scratch, which OS should I install first? And then, how do I set up the partitions to install the other OS? Let me know if you have any questions. Thanks for your help.

  Read the article

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  Hello, I recently did a full upgrade of windows 7 on my thinkpad, everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen just before the Windows logo appears, disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this wont boot with battery plugged in is greatly appreciated - i need to take this battery out on the road/trains etc.... Cheers Matt

  Read the article

• Dual boot OSX and Windows 7 natively

  - by Phill

  I'm considering getting one of those new fancy Mac Book Pro's with the fancy screens, but after reading some stuff on the internets about running Windows 7 with bootcamp: https://discussions.apple.com/thread/2770866?start=0&tstart=0 It seems you can't use the integrated graphics with windows, this causes windows to chew the battery life: I am afraid it is not possible. Since Apple introduced dual graphics chip laptops, they kept the low power/embedded GPU hidden under Window and they expose only the power hungry discrete GPU. It feels that this is being done on purpose so that it appears to users that OS X offers a better experience and battery life over Windows. So running bootcamp and windows kills the battery, running in parallels means you don't get accelerated 3d support (or something along those lines), so you don't get the performance out of it. I'm wondering: Is it possible to natively dual boot Windows 7 on a MBP, and if so would/does that give windows access to the integrated graphics to be able to not rape the battery?

  Read the article

• CPU fan twitching phase leds blinking - computer won't boot

  - by SooX

  I have a big problem that I got today. Yesterday computer was "on" normally, I went to sleep without shutting it down. When I woke up, I heard a strange sound and was unable to bring it up from hibernate. I unplugged the PSU. When I plugged the PSU back in, the sound came back. When I opened the case, I saw the fan "twitching" like it is about to start and fan LEDs were blinking. Also, motherboard LEDs were blinking in the same pattern - the first green one has more of luminosity then others. When I cut down the power with 0/1 button on PSU, the fans continue to make sounds like the machine is trying to boot before the capacitors run out and the power dies. Does anyone have a clue what to do? I tried disassembling everything but that doesn't work. I will try with friend's PSU later today.

  Read the article

• HP proliant dl360 g5 fails to reboot

  - by user1039384

  Some history of this also available here. As of my latest update on the forum linked above, now cold reboot as well as hard reset and following boot for my proliant dl360 g5 works as expected and successfully boot the system. However, soft-reboot results in internal health indicator turning RED on the front and long beeps every around 6seconds until I either cold reboot or press and hold the power button. A summary of system state when this happens: Internal Health led indicator: RED External Health led indicator: Green No led next to any component is red or amber No POST message neither on the video output nor on IML logs (verified both at the time issue occures and after cold reboot that boots the system successfully). Any thoughts please share. I hope we can knock this issue down together with your help!

  Read the article

• Windows 8 to 8.1 Pro Upgrade SecureBoot Error

  - by Alexandru

  I upgraded from Windows 8 to Windows 8.1. I have an Alienware Aurora R4 with the latest BIOS firmware version, A09. Ever since I did the upgrade, I get a watermark on my desktop saying, "SecureBoot isn't configured correctly"...I would like to get rid of this watermark the correct way (not by hacking system DLLs). My BIOS shows me booting in UEFI mode, and I see that SecureBoot is actually disabled from there. I cannot enable SecureBoot, in either UEFI mode or Legacy Boot mode. Note, I can't even get Legacy Boot mode working without re-formatting my system which I really don't plan on doing, so my question is this...what has changed in the way Windows handles SecureBoot? As far as I can tell, I do not have SecureBoot enabled, and it is trying to tell me that it isn't configured correctly. Why does it even care to check if my BIOS doesn't have it on anyways?! Its so frustrating!

  Read the article

• Windows 8.1 will not boot after upgrading from Windows 8 on my PC

  - by user266969

  I have not found a fix. After running the Windows 8.1 Update from the store my computer will not boot unless In insert my recovery USB drive and try to repair. (The repair fails.) However after I power of the PC and remove the USB drive. The PC will boot correctly once. I would leave the PC on but it shuts it self off at night. (And yes I have checked my power profile, it is set to never.) The only thing I have found online is a possibly corrupt video driver. I uninstalled the video driver reboot and it did not fix the issue. Anybody have any suggestions? The PC is a HP EliteBook 8730w laptop. I had no issues with Windows 8 or the Windows 8.1 preview.

  Read the article

• Windows - CPU power management APIs

  - by iulianchira

  What APIs are provided by Windows for CPU power management (I'm interested in CPU frequency scaling, setting min and max CPU frequency - similar to what you can do in Control Panel in power plans, but in a programmatic way). I'm also interested in .Net APIs.

  Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >