Search Results

Search found 20358 results on 815 pages for 'disk management'.

Page 45/815 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

• Clone Windows 7 to bootable USB disk

  - by Geziefer

  I saw some posts here having a similar topic, but I haven't quite found what I am looking for. All I need to do is transfer my Windows 7 (Professional, 64bit) which is installed on an internal disk on my Dell Latitude laptop to an external USB disk in order to have my original system available for booting while installing a new system on the internal disk, which is essential since I need a working project environment for work in case the new system takes some days until fully completed. I already tried a disk clone with Acronis and Clonezilla, but in the 1st case it didn't even booted the clone and in the 2nd case it booted, but stopped with a bluescreen (and rebooted too fast to be able to see any error code). So has someone done successfully what I am trying to do and can help me out here?

  Read the article

• Read/WRITE/Verify disk diagnostic tool for Mac OS X?

  - by Spiff

  It seems that there are many tools out there for Mac OS X that test a hard drive for bad blocks by doing a Read/Verify pass. That is, they read a block, then read it a second time, and verify that both reads yielded the same results. I need a tool that does a non-destructive Read/Write/Verify pass. It should read each block, write those same contents back out, and then read it again to verify. That way every block gets written, giving the hard drive a chance to spare out bad blocks. But since the same contents that were just read get written back out, it doesn't destroy data that wasn't already lost. I'm aware of several tools that can do Read/Verify, but I'm not aware of any that do Read/Write/Verify. Are there any tools that do what I want? Unix / open source tools that compile and run on Mac OS X are fair game too.

  Read the article

• Move virtual machine hard disk to a separate physical hard disk for better performance?

  - by joeeoj

  I have a dual-core machine with the host OS and many guest virtual OSs. Although I have 8GB of RAM, I notice a slowdown when I turn some virtual machine on (and it takes only 1GB RAM). I was told that I should move virtual machine hard disk file to a separate (another) physical hard drive in my PC to get better performance. This way the head of the hard disk would not have to jump from the virtual OS to the host OS as each hard drive would have its own head to deal with the OS: hard drive 1 head for host OS and hard drive 2 head for guest OS. Is this true? Should I get another hard disk only for virtual machine hard disk files?

  Read the article

• OLTP Sql Server RAID configuration with 10 disks, allocation Unit and disk stripe size

  - by Chris Wood

  On a new db server I only have 10 disks to play with, The usage is about a booking every 3-5 seconds, so not high volume, I know compromises have to be made, but my initial thoughts are - DISK 1 & 2 - RAID 1 - OS DISKS 3,4,5,6 - RAID 10 - Data, Indexes & TempDB DISKS 7,8,9,10 - RAID 10 - Logs & Backup Full backups will take place when there is virtually no traffic on the website so not bothered about the contention with the logs. disk 3-10 - 8kb NTFS unit allocation size disk 3-10 - 64kb Disk Stripe size does this seems to be sensible, any other considerations I have omitted ? thanks

  Read the article

• Migrate Windows Server 2008 to a new hard disk

  - by MainMa

  Hi, I have a machine with Windows Server 2008. I want to change the hard disk drive, but keep everything else. I don't have a cd/dvd drive and don't want to buy it. My first idea was to make a byte-to-byte copy of the disk with Paragon Advanced Recovery. The problem is that when I try to boot from a new hard disk, it says that there were hardware changes and that Windows must be repaired, inviting me to insert the installation disk and follow repair instructions. I searched and found that 1:1 copy is not a correct way to do things. The correct one is to restore Windows to a new hard disk from a full system backup. But to restore, I need to have a dvd drive. I tried to make a copy of the Windows Server 2008 .iso on an USB flash drive, but the drive is not bootable (while the same procedure applied to Paragon Advanced Recovery ISO produces a bootable recovery USB flash drive). Now what else can I do (except buying a dvd drive)? Is there a way either to make Windows work without doing recovery or recover Windows 2008 without using a cd drive?

  Read the article

• Which upgrade path for disk IO bound postgres server?

  - by user41679

  Hi all, We currently have a Sun x4270 with 2xquad core Xeon Nehalmen 2.93ghz cores (16 threads), 72 gig of ram and 16 x 10k SAS disks split between the os raid 1, a partition for the Write Ahead Logs which is raid 10 and a partition for the database tables and indexes which is also raid 10, all xfs. I'm currently evaluating which path to go down in terms of upgrades. We'll be sharding the DB at some point soon, but for now I need to focus on hardware upgrades specifically. The machine is not CPU or memory bound at all at the moment, just IOWait is become an issue. The machine is mostly write access as we have a heavy caching layer. We're seeing about 300 write IOPS average on both the database partitions. We don't have any additional storage infrastructure like a Fiber Channel or ISCSI network. Budget isn't too much of a concern, something inline with the size of this server (i.e no $1m IBM machines) Space is ok on the DB side of things, we're running out obviously but there's also some reduction we can do. Additional space would be good though. My current thoughts are either: * ISCSI SAN, possible with 10Gbit network that has solid state acceleration. * FusionIO card / Sun F20 card (will the FusionIO card work in the Sun box? * DAS shelf (something like this http://www.broadberry.co.uk/das-direct-attached-storage-servers/cyberstore-224s-das) which a combination of 15k sas disks and some Intel X25-E drives for DB indexes etc) what would I need to put in the x4270 to add a DAS shelf? I think it's a SAS HBA card, do I have to use Sun's own card or will any PCI Express card work? Anything else??? what would you guys do from your experience? I appreciate it's a lot of questions, but I haven't expanded a DB machine for a number of years and the landscape has changed dramatically since then! Any advice or feedback would be very much appreciated. Let me know if there's anything else I can clarify. Thanks in advance!

  Read the article

• Can't select hard disk off Windows 7 system image creator

  - by David

  When I try to create a system image in Windows 7 from the Control Panel (Control Panel\All Control Panel Items\Backup and Restore) I get the option to select a hard disk or a removeable disk to select, I have 2 disks and wanted to create the image on my spare one. However when I click refresh it doesn't show either of my disks but shows my CDROM under the removable disks area, anyone have this problem? Also, when I select a USB disk instead, it tries to iamge both my disks! I can't select my active Windows 7 installed disk! How pointless!

  Read the article

• suggestions for migrating a windows 7 install to a new 4K sector disk

  - by myCubeIsMyCell

  Hi, I'm looking to upgrade the disk on a windows 7 box to a new larger drive. In the past for such migrations I'd just hook both drives up and use a linux boot disk and use dd to copy from one disk to the next... boot up the new drive & expand the partition. The drive I just purchased however is a western digital using 4k sectors... not sure if there'd be any complications using my old method moving from a 512b sector drive. Current plan is to try the migration by doing a win7 system image backup to an external drive... then restore the image to the new drive via system restore boot disk. Any suggestions or recommendations on how to best complete this migration would be greatly appreciated. Thanks!

  Read the article

• install grub on disk image

  - by Dima

  I have disk image with 2 partitions: Partition 1 has cramfs file system (read only). This partition contains all system files of the OS Partition 2 has ext3 file system. This partition has only configuration files that may be changed. How can I install GRUB1 boot loader on MBR. I tried to copy first 446 bytes of my hard disk and copy GRUB files to the /boot directory on the 1st (cramfs) partition. I cannot use grub-install because I have disk image and not disk itself. Any ideas?

  Read the article

• Thecus N5200, disk has dropped out of RAID5

  - by Anders Ekdahl

  We have a Thecus 5200 NAS here at work with five WD Caviar Black 2TB disks in a RADI5 array. Yesterday, disk 4 dropped out of the array, and in the NAS web interface there's a warning about the RAID array being "degraded". When I go into Storage - Disks, disk 1 and 4 has a warning next to them. When I click on the warnings, this information about the disks are displayed: Tray Number 4 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 34 Reallocated Sector Count 66 Current Pending Sector 1447 Raw Read Error Rate 61 Seek Error Rate 0 Hardware ECC Recovered N/A Tray Number 1 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 32 Reallocated Sector Count 0 Current Pending Sector 1465 Raw Read Error Rate 0 Seek Error Rate 0 Hardware ECC Recovered N/A I'm not really an expert on either disks or RAID arrays. Does this indicate that the fourth disk is damaged, and needs to be replaced? And what about disk number one? It has a warning, but it's still in the array. Is it safe to add the fourth disk back into the array as a spare? I can't find any way to add it back as a it were before.

  Read the article

• Problem with slow hard disk

  - by Makis Arvin

  We bought some new PCs in my company with the new iCore 7 and 8GB memory and the following hard disk: WESTERN DIGITAL WD8000AARS 800GB CAVIAR GREEN SATA2 The problem we have is that after installing windows XP64 SP2 the write speed of the hard disk is extremely low!. The windows system monitor shows that the Average Disk queue length is always at 100% and a winzip extract of 350mb takes about 8min. Is there any idea on where to start looking for the cause of that? Thanks

  Read the article

• Letting users make their own dns changes? Any software available to manage this tricky situation?

  - by Jaredk

  I currently waste a lot of time making dns changes for my organization. DDNS of course helps for workstations, but we still have a few thousand unique servers with still more applications needing cname records that DHCP/DDNS alone will not support, so someone needs to make updates, but I'd like to see sysadmins make their own dns updates for their machines. I'm currently working on extending our asset database to support this functionality, but I hold out hope that there are COTS solutions available.

  Read the article

• What is a good encryptable disk image format suitable for rsync on a PC?

  - by Greg Joshner

  I’m looking for a solution to encrypt my XP home directory and then rsync the encrypted image file to a remote server. Since I don’t want to transfer several Gigs for even the smallest change in the image I’m looking for a solution which saves the image “chunked” into smaller files. That way Rsync can transfer only the changed elements. Do you have any ideas? Thanks a lot for your help!

  Read the article

• Sporadic disk clicking sound

  - by Abdó

  Hi, I'm having some unusual and sporadic hard disk clicking issues. Here is a cronological description of the facts. I'm using an ASUS P6T-SE with Intel Core i7, 6Gb RAM 600W Power supply and ATI4670 graphics, running Ubuntu 10.10. About one month ago my hard disk (SATA II Seagate Barracuda 1Tb 7200 rpm) started making a clicking sound: a sort of loud tic-tac, every second or so, when involved in disk activity. The system was clearly slower than before at disk access, but it was functional and I could not find any signal of trouble on the linux logs. I disconnected the disk and tried an older SATA drive I had around: no problem with it. Then I reconnected the Seagate disk, and the problem was mysteriously gone. Ubuntu booted normally, usual speed, no clicking. A couple of weeks later, the problem reappeared. I tried disconnecting reconnecting (as it somehow solved the problem before) without luck. So, despite it was a rather new drive, I assumed it was a hardware issue, made backups and bought a new drive. The new drive is a SATA II Seagate Barracuda 1.5 Tb 7200 rpm. I installed both drives at the same time, with the intention of transferring my files from on to the other. To my surprise, when I booted the computer with both drives, both started making the clicking sound !! Even worse, I removed the old drive, leaving the unformated new drive connected, and booted from a LiveCD. It kept clicking ! Puzzled by this, I tried both drives on my laptop with a SATA to USB cable. At the moment I connected any of them, they made one or two unusual clicks and immediately stopped doing that and worked normally. The old drive I thought almost dead, was working like a charm as if nothing happened. Then I thought: "ok, it must be the motherboard. Let's try again". So, I reconnected the old drive to the ASUS P6T motherboard (the same cables and SATA port as before), and it worked as if nothing happened ! The problem was gone again. The new 1.5 Tb drive was also working ok: No clicking nor slowdown. So I left the old 1Tb disk connected and kept using the computer daily during 3 weeks, until today it happened again. Now I don't really know what to do or check. I'm not even sure if it is a hardware issue any more ! This is rather annoying as it seems it happens with a period of 2 or 3 weeks and I have no means of forcing it to happen. Does anyone have a clue of what can causes this behaviour or have any suggestions of things I should check when it happens again ? What I did today is checking some SMART parameters Error log: smartctl -l error /dev/sda. No errors Short selftest: smartctl -t short /dev/sda. No errors Disk Health check: smartctl -H /dev/sda. passed And here are the vendor specific parameters (smartctl -A /dev/sda) Which I'm not quite sure how to interpret. === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 120 099 006 Pre-fail Always - 235962588 3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 187 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 16348045 9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 3590 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 94 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 097 000 Old_age Always - 4295164029 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 070 057 045 Old_age Always - 30 (Lifetime Min/Max 19/31) 194 Temperature_Celsius 0x0022 030 043 000 Old_age Always - 30 (0 18 0 0) 195 Hardware_ECC_Recovered 0x001a 037 026 000 Old_age Always - 235962588 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 73950746906346 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1832967731 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3294986902 Any clue to this mystery will be really welcome. Thank you very much !!

  Read the article

• "A disk read error occurred" after choosing to boot into Windows XP from GRUB

  - by kellogs

  "A disk read error occurred" appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris Here, sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I cannot recall how exactly have I used testdisk but it once said: Disk /dev/sda - 160 GB / 149 GiB - CHS 19458 255 63 The harddisk (160 GB / 149 GiB) seems too small! (< 169 GB / 157 GiB) Check the harddisk size: HD jumper settings, BIOS detection... So far I have tried to "fixboot" and "chkdsk" from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please? Thank you!

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state [closed]

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results.

  Read the article

• Reconstructing the disk order in RAID 6 with 7 disks

  - by rkotulla

  a little background to this question first: I am running a RAID-6 within a QNAP TS869L external RAID/NAS system. I started with 5 disks of 3 TB each back in the day, and later added another 2 disks of 3TB to the RAID. The QNAP internals handled the growing and re-syncing etc, and everything seemd to be perfectly fine. About 2 weeks ago, I had one of the disks (disk #5, disk #2 has gone bad in the mean time) fail, and somehow (I have no idea why), also disks 1 and 2 got kicked out of the array. I replaced disk #5, but the RAID didn't start working again. After some calls to QNAP technical support, they re-created the array (using mdadm --create --force --assume-clean ...), but the resulting array couldn't find a filesystem, and I was kindly referred to contact a data recovery company that I can't afford. After some digging through old log files, resetting the disk to factory default, etc, I found a few errors that were made during this re-create - I wish I still had some of the original metadata, but unfortunately i don't (I definitely learned that lesson). I'm currently at the point where I know the correct chunk-size (64K), metadata-version (1.0; factory default was 0.9, but from what I read 0.9 doesn't handle disks over 2 TB, mine are 3 TB), and I now find the ext4 filesystem that should be on the disks. Only variable left to determine is the right disk order! I started using the description found in answer #4 of "Recover RAID 5 data after created new array instead of re-using" but am a little confused on what the order should be for a proper RAID-6. RAID-5 is pretty well documented in a number of places, but RAID-6 much less so. Also, does the layout, i.e. distribution of parity and data chunks across the disks, change after the growing of the array from 5 to 7 disks, or does the re-sync re-organize them in such a way a native 7-disk RAID-6 would have been? Thanks some more mdadm output that might be helpful: mdadm version: [~] # mdadm --version mdadm - v2.6.3 - 20th August 2007 mdadm details from one of the disks in the array: [~] # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 1.0 Feature Map : 0x0 Array UUID : 1c1614a5:e3be2fbb:4af01271:947fe3aa Name : 0 Creation Time : Tue Jun 10 10:27:58 2014 Raid Level : raid6 Raid Devices : 7 Used Dev Size : 5857395112 (2793.02 GiB 2998.99 GB) Array Size : 29286975360 (13965.12 GiB 14994.93 GB) Used Size : 5857395072 (2793.02 GiB 2998.99 GB) Super Offset : 5857395368 sectors State : clean Device UUID : 7c572d8f:20c12727:7e88c888:c2c357af Update Time : Tue Jun 10 13:01:06 2014 Checksum : d275c82d - correct Events : 7036 Chunk Size : 64K Array Slot : 0 (0, 1, failed, 3, failed, 5, 6) Array State : Uu_u_uu 2 failed mdadm details for the array in the current disk-order (based on my best guess reconstructed from old log-files) [~] # mdadm --detail /dev/md0 /dev/md0: Version : 01.00.03 Creation Time : Tue Jun 10 10:27:58 2014 Raid Level : raid6 Array Size : 14643487680 (13965.12 GiB 14994.93 GB) Used Dev Size : 2928697536 (2793.02 GiB 2998.99 GB) Raid Devices : 7 Total Devices : 5 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Jun 10 13:01:06 2014 State : clean, degraded Active Devices : 5 Working Devices : 5 Failed Devices : 0 Spare Devices : 0 Chunk Size : 64K Name : 0 UUID : 1c1614a5:e3be2fbb:4af01271:947fe3aa Events : 7036 Number Major Minor RaidDevice State 0 8 3 0 active sync /dev/sda3 1 8 19 1 active sync /dev/sdb3 2 0 0 2 removed 3 8 51 3 active sync /dev/sdd3 4 0 0 4 removed 5 8 99 5 active sync /dev/sdg3 6 8 83 6 active sync /dev/sdf3 output from /proc/mdstat (md8, md9, and md13 are internally used RAIDs holding swap, etc; the one I'm after is md0) [~] # more /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md0 : active raid6 sdf3[6] sdg3[5] sdd3[3] sdb3[1] sda3[0] 14643487680 blocks super 1.0 level 6, 64k chunk, algorithm 2 [7/5] [UU_U_UU] md8 : active raid1 sdg2[2](S) sdf2[3](S) sdd2[4](S) sdc2[5](S) sdb2[6](S) sda2[1] sde2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdg4[3] sdf4[4] sde4[5] sdd4[6] sdc4[2] sdb4[1] sda4[0] 458880 blocks [8/7] [UUUUUUU_] bitmap: 21/57 pages [84KB], 4KB chunk md9 : active raid1 sdg1[6] sdf1[5] sde1[4] sdd1[3] sdc1[2] sda1[0] sdb1[1] 530048 blocks [8/7] [UUUUUUU_] bitmap: 37/65 pages [148KB], 4KB chunk unused devices: <none>

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results. I also tried all the suggestions from this question Why doesn't Windows 7 wake up from sleep?. Still no results.

  Read the article

• Goal setting/tracking packages for software projects

  - by Avi

  I'm a developer working by myself. I'm looking for a computerized tool to manage my goals and activities. I own it Microsoft Project, but I don't like it. I've started many "projects" but could never keep on using it. Too complex and heavyweight for me. I use MS-Outlook tasks. They are not what I need. No planning capability. Tracking is not nice. I'm using the Pomodoro technique and I like it, but I'm looking for something more comprehensive and with better computerized support. Something that would allow me to define goals with dependencies and time estimation, keep daily prioritized lists etc. So, I'm looking for a solution. One I've found is GoalPro, but I uneasy because I could not find a cross-product "top ten" like review. Are you using any goal setting package such as GoalPro? Which? Does it help? Pros and Cons?

  Read the article

• SAS disk performance drops a while after reboot.

  - by Flamewires

  So we have some workstations with identical hardware. The Fedora14 box has a couple weeks uptime and still get good performance. hdparm -tT /dev/sda /dev/sda: Timing cached reads: 21766 MB in 2.00 seconds = 10902.12 MB/sec Timing buffered disk reads: 586 MB in 3.00 seconds = 195.20 MB/sec The Cent 5.5 boxes however seem to be okay after a reboot, /dev/sda: Timing cached reads: 34636 MB in 2.00 seconds = 17354.64 MB/sec Timing buffered disk reads: 498 MB in 3.01 seconds = 165.62 MB/sec but some time later( unsure exactly, tested at approx 1 day uptime) /dev/sda: Timing cached reads: 2132 MB in 2.00 seconds = 1064.96 MB/sec Timing buffered disk reads: 160 MB in 3.01 seconds = 53.16 MB/sec drop to this. This is with very low load. I believe they all have the same bios settings. Any ideas what could cause this on Cent? Ask for more info. It might also be worth noting, that passing the --direct flag causes the slow boxes to perform similarly to the non-slow ones for buffered disk reads.

  Read the article

• Looking for a good free or cheap task tracking system

  - by JWood

  I've finally decided that pen and paper/whiteboards are not up to the job as my workload increases so I'm looking for a good task tracking system. I need something that can track tasks in categories (projects) and allow me to assign priority to each task. I've tried iTeamWork which requires projects to have an end time which is no good for me as at least one of my projects is ongoing. I also tried Teamly which was required tasks to be set to a specific day which is no good as tasks sometimes take more than a day and I would like them organised by priority rather than specific days. Preferably looking for something hosted but I'm happy to install on our servers if it supports PHP/MySQL. Oh, and an iPhone client would be the icing on the cake! Can anyone recommend anything?

  Read the article

• How do I recover drivers from other hard disk

  - by Carl

  The drivers for a Cardbus (PCMCIA) card that gives me 2 USB 2.0 ports are on the hard disk from my old laptop. I have lost the driver CD. I have a way to get files from that other hard disk. Which files do I need? The drivers for the card used to be on the following website - the information is still there, except the download links don't work: http://www.ht-link.com/en/DownView.asp?ID=10 - The drivers I need are the first listing - The Win XP drivers for the HT-112NEC. My e-mails to them have not been answered. The information on this card is here http://www.ht-link.com/en/ProductView.asp?ID=106 I already tried connecting that other drive to my new laptop (via USB) and adding the drive to the search criteria when selecting update driver in the Device Manager. It says there isn't a better match, and if I select manual the matching device is not listed. (I don't think "manual" sees drivers on the external hard disk - but only ones on the main drive and/or found listed in the registry.) I would try 'have disk' if I knew exactly what file to point to on the external drive. The drivers are on that hard disk - I installed them there, and used that card on that computer. The new laptop has Windows XP Pro SP3, the old one had Pro SP2 Thanks for any help.

  Read the article

• Windows 8.1 Update 1 Disk Usage 100%

  - by Gookjin Jeong

  Background Information / Computer Specs I have a 14-inch Samsung Series 5 Ultra. Core i5 CPU, 750GB HDD, 8GB RAM, Intel HD Graphics 4000. I've had the computer for about 1.5 years with no major problems. Problem The issue appeared at the beginning of April this year, when I updated the OS to Windows 8.1 Update 1 (not from 8 to 8.1). After being on continually (except for at night, when I put it on sleep mode) for about 48 hours, the disk usage as seen by Task Manager hits 100%. When this happens, everything from opening/closing applications to typing and even bringing up the start screen by pressing the Windows key becomes extremely slow. The only way to make the disk usage decrease is to restart the computer. Then the problem repeats. I've used my current laptop (as well as my previous laptops) this way -- putting it on sleep mode at night and restarting it only when Windows needs to install updates -- for a long time. So I know the 100% disk usage is not due to the way I use the computer. The thing that causes the spike varies. Sometimes it's System, sometimes it's one of the various applications I installed (e.g. Chrome, Evernote, Spotify, Wunderlist, iTunes, etc.), and sometimes it's Antimalware Service Executable, etc. Tried Solutions I think I tried almost every solution out there for this problem: Running the check disk command (chkdsk /b /f /v /scan c:) from Admin Command Prompt Running Windows Memory Diagnostic Disabling Superfetch and Windows Search from services.msc Running "Fix problems with Windows Update" from Control Panel -- Troubleshooting Updating and rolling back the graphics driver (Intel HD 4000) Disabling "Use hardware acceleration when available" from Chrome settings Disabling Intel Rapid Storage Technology Running the SFC /SCANNOW command as recommended here Running a quick scan & a full scan from Windows Defender (no threats found) Taking the hard drive out and putting it back Refreshing the computer, from the Update and recovery -- Recovery option in Windows settings NONE of the above worked for me. I was about to give up but then noticed that one of the main culprits of the disk usage spike, as shown in the "Disk Activity" section of the Resource Monitor, was C:\System (pagefile.sys). I googled around and found that one of the recommended solutions was to disable pagefile. I then went to **Control Panel -- System and Security -- System -- Advanced system settings -- Advanced tab -- Performance settings -- Advanced tab -- "Change" under Virtual memory and discovered that the number for "Currently allocated" at the bottom was 1280MB, although the number for "Recommended" was 4533MB. I immediately changed it to 4533MB and checked my family members' computers to see what the numbers were like. All of theirs had a currently allocated space that was only slightly smaller than the recommended space. See screenshot below: This might fix the problem. I'll have to wait a couple more days.But if it doesn't, what in the world should I do next? I'm guessing the hard drive isn't failing because This computer is less than 2 years old; and Speccy says that the status of the HDD is good. Update 5/27/2014 The "4533MB" solution did not work. I had to reboot the computer about 30 minutes ago because the disk usage again hit 100%. When I opened Resource Monitor the C:\System (pagefile.sys) again was shown to be the culprit. I have now disabled pagefile entirely via the same window shown above in the screenshot. The number for "currently allocated" is now 0MB. Will update again in a couple days, or if the problem occurs again, whichever comes sooner.

  Read the article

• Infected Win XP disk not openable on a Vista computer

  - by Retired57

  How can I read a WinXP partioned disk that is infected and shows up on a USB connection to Win Vista computer as a single partition that Vista cannot see the contents? The XP computer HDD is partioned into 4 partitions. It became infected, and all attempts to clean it have failed. Applications begin to launch, but are then shut down by the infecting agent. Using a major Anti-virus Co. boot disk (which was unable to connect to the Web, probably because the infecting agent stopped it) with virus definitions dated after the disk became infected, the resultant scan showed no infection. I bought a USB cable to connect the IDE drive to my Vista computer, but when I open Win Explorer, it sees the disk, but does not show any contents. It indicates it is a single partition that is valid. However in all the ways I have tried it does not show drive contents. Any suggestions on what to do next?

  Read the article

• How do I free some disk space so Ubuntu will boot again?

  - by Omkant

  I have installed Windows and Ubuntu side by side. I created a 10GB partition for the Ubuntu installation. During the two months I've been using Ubuntu I have installed some software. Now it's not starting. When I boot up it says that there is no diskspace so it could not be started . What can i do now? When I boot up all I get is a black screen terminal with a $. Please help me with a command to uninstall some programs and start using Ubuntu or any other way to get rid of this message.

  Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >