Search Results

Search found 3084 results on 124 pages for 'lan'.

Page 45/124 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

• Is there a way to suspend/sleep via bash?

  - by Brett Alton

  I have to get nine 46" LCD monitors (running Windows) to suspend/sleep at 8pm and wake at 8am every morning. It's been a bit of a mess trying to get the commands working, including the privileges. Since I'm an Ubuntu user first and foremost, I'm wondering how easy this would be in Ubuntu/Linux. I know cron would be able to run my suspend/sleep command at 8pm (what is the suspend/sleep command anyway?), but what about waking the machine up at 8am without using Wake-on-Lan or manual intervention?

  Read the article

• Network Administrators Past, Present, and Future

  Even in the short time that PCs have been signficantly networked, what it means to be a SysAdmin has changed dramatically. From the first LAN parties to the lumbering infrastructures of today, the role of SysAdmin has evolved and adapted to the shifting needs of users and corporations alike. Brien Posey has been on the front line of it all, and considers the future of this thus-far essential IT role.

  Read the article

• Why wifi doesn't work in this case?

  - by xRobot

  I have a brand new notebook where I have installed Windows 7 and Ubuntu 12.04 LTS 64bit in dual boot. In windows 7 wifi works but in Ubuntu not. Could you help me please ? iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off eth0 no wireless extensions. lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 07 serial: b4:b5:1f:1b:9a:56 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:3000(size=256) memory:c2404000-c2404fff memory:c2400000-c2403fff *-network description: Wireless interface product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 84:4b:f4:0a:3a:22 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-31-generic firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:c2500000-c250ffff lspci | grep -i net 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) 02:00.0 Network controller: Ralink corp. Device 539a iwlist scan lo Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Device or resource busy eth0 Interface doesn't support scanning. lsmod Module Size Used by rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224173 1 joydev 17693 0 hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 97362 0 snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device arc4 12529 2 rt2800pci 18715 0 rt2800lib 58925 1 rt2800pci crc_ccitt 12667 1 rt2800lib rt2x00pci 14577 1 rt2800pci rt2x00lib 51144 3 rt2800pci,rt2800lib,rt2x00pci mac80211 506816 3 rt2800lib,rt2x00pci,rt2x00lib soundcore 15091 1 snd mac_hid 13253 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev wmi 19256 1 hp_wmi i915 473240 3 cfg80211 205544 2 rt2x00lib,mac80211 eeprom_93cx6 12725 1 rt2800pci drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 serio_raw 13211 0 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid r8169 62099 0 rfkill list: # rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• SSH from external network refused

  - by wulfsdad

  I've installed open-ssh-server on my home computer(running Lubuntu 12.04.1) in order to connect to it from school. This is how I've set up the sshd_config file: # Package generated configuration file # See the sshd_config(5) manpage for details # What ports, IPs and protocols we listen for #Port 22 Port 2222 # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key HostKey /etc/ssh/ssh_host_ecdsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH #LogLevel INFO LogLevel VERBOSE # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords #PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net Banner /etc/sshbanner.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. UsePAM yes #specify which accounts can use SSH AllowUsers onlyme I've also configured my router's port forwarding table to include: LAN Ports: 2222-2222 Protocol: TCP LAN IP Address: "IP Address" displayed by viewing "connection information" from right-click menu of system tray Remote Ports[optional]: n/a Remote IP Address[optional]: n/a I've tried various other configurations as well, using primary and secondary dns, and also with specifying remote ports 2222-2222. I've also tried with TCP/UDP (actually two rules because my router requires separate rules for each protocol). With any router port forwarding configuration, I am able to log in with ssh -p 2222 -v localhost But, when I try to log in from school using ssh -p 2222 onlyme@IP_ADDRESS I get a "No route to host" message. Same thing when I use the "Broadcast Address" or "Default Route/Primary DNS". When I use the "subnet mask", ssh just hangs. However, when I use the "secondary DNS" I recieve a "Connection refused" message. :^( Someone please help me figure out how to make this work.

  Read the article

• DVG834N - A Single Device for All the Requirements to Build a Faster, Hassle Free, And Secured Netwo

  DVG834N Product Family is a Wireless ADSL Router with 2 Voice lines gateway, Wireless ?N access point, four-port 10/100 Mbps LAN Switch, and USB 2.0 Host ? a perfect solution for your home environmen... [Author: Ki Grinsing - Computers and Internet - May 10, 2010]

  Read the article

• Multi subnet in ubuntu with dnsmasq

  - by Fox Mulder

  I have a multi lan port box that install ubuntu server 11.10. I am setup network in /etc/network/interfaces file as follow: auto lo iface lo inet loopback auto eth0 iface eth0 inet static      address 192.168.128.254      netmask 255.255.255.0      network 192.168.128.0      broadcast 192.168.128.255      gateway 192.168.128.1      dns-nameservers xxxxxx auto eth1 iface eth1 inet static      address 192.168.11.1      netmask 255.255.255.0      network 192.168.11.0      broadcast 192.168.11.255 auto eth2 iface eth2 inet static      address 192.168.21.1      netmask 255.255.255.0      network 192.168.21.0      broadcast 192.168.21.255 auto eth3 iface eth3 inet static      address 192.168.31.1      netmask 255.255.255.0      network 192.168.31.0      broadcast 192.168.31.255 I am also enable the ip forward by echo 1 /proc/sys/net/ipv4/if_forward in rc.local. my dnsmasq config as follow except-interface=eth0 dhcp-range=interface:eth1,set:wifi,192.168.11.101,192.168.11.200,255.255.255.0 dhcp-range=interface:eth2,set:kids,192.168.21.101,192.168.21.200,255.255.255.0 dhcp-range=interface:eth3,set:game,192.168.31.101,192.168.31.200,255.255.255.0 the dhcp was working fine in eth1,eth2,eth3, any machine plug in the subnet can get correct subnet's ip. My problem was, each subnet machine can't ping each other. for example. 192.168.11.101 can't ping 192.168.21.101 but can ping 192.168.128.1 192.168.31.101 can't ping 192.168.21.101 but can ping 192.168.128.1 I am also try to using route add -net 192.168.11.0 netmask 255.255.255.0 gw 192.168.11.1 (and also 192.168.21.0/192.168.31.0) at this multi-lan-port machine. But still won't work. Does anyone can help ? Thanks.

  Read the article

• Button "Add" is disabled in VPN Connection's dialog

  - by Innuendo

  I've just installed elementaryos-jupiter. (It's based on Ubuntu 10.10) I've entered VPN Connections' menu (nm - VPN Connections - Configure VPN) And there should be button "Add" - it is, but it's disabled (I can't press on it) I'm connecting via ethernet (LAN in a students' hostel) and we get internet via VPN connection (It worked for me in Ubuntu for a few years) Any suggestions? I've asked on IRC of elementaryos (there were few people) but they said that VPN is out-of-box, and it should work - they never met this.

  Read the article

• Path of Replication

  - by geeko

  I'm currently developing a replication system to keep data in-synch between an arbitrary number of servers. Some of these servers exist in one cluster on one LAN. Others exist somewhere else in the world. I'm wondering what are the pros/cons of different paths that we choose to flow replicated data on between servers? In other words, what are the different strategies to load balance the replication process ?

  Read the article

• No firmware found for b43 wireless controlloer (BCM4318) on a Dell Latitude D610

  - by Stanton.Sculpture

  Trying to get my 03:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) working. I just reformated and installed 12.04 on this old Windows XP machine, and I don't know where to get the firmware for this. This is what I got when I typed sudo lshw -c network: http://pastebin.ubuntu.com/1041161/ Also, when I go to additional drivers in the system settings, no proprietary drivers show up. Any help I can get on this would be Great, Thanks!

  Read the article

• Multiuser's impact on Access Database

  - by SilentRage47

  Can someone explain to me how are effected the performances of an Access 2003 DB when it's used by a lot (30) of users on the same LAN? I'm working on a vb6 project with this access 2003 DB wich performs ok on my local PC, but it's terrible when used across 20-30 users. It's there something I can do to improve performance? How can I understand what's the cause of this degradation in performance?

  Read the article

• Set Idle Time in Ubuntu 12.04 Server

  - by ssanj

  I recently installed Ubuntu 12.04 Server and am looking for away for get the server to suspend after an idle time. When using the desktop version I could use the Gnome powersaving tool to specify the idle time. As I have no GUI on the server is there a way to set the server idle time via the commandline/config file? I will send the server a wake-on-lan packet to wake it up, if it is suspended and I need to use it.

  Read the article

• 11g R2 RAC Expert ????????? ~???~

  - by user763243

  ????????????????????????????????????????????????????????????????????????????????????(??????????????????????????????????)???????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????15???????????????????????????????????????????40????? ?????????????? ???????????????????????????????????????????2?????????????????????????????????????????????????????????????????????????????????????????????????(??????????????????????????????????????????????????????????????????????)?????????????????????????????????????? ???????????????????????????????? ????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ???????????????????????Oracle ??????·????????????????????????Activate?????????????????????????????Activate?????????????????1???2???3???4?????????????????1??????????????????30???????????????????????????????????????????????????????????????????????”???”????????????????WiFi??????????????????? ????????LAN???????????????????????????????????

  Read the article

• Handshake violation when trying to access one website

  - by Miguel

  I have a TZ 190 Wireless Enhanced with SonicOS Enhanced 4.2.1.0-20e. Yesterday, people could access without any problems a bank website wich uses HTTPS. Today, it is imposible to access only that website, every other ones works without problems. When checking the log message filtering to my IP only, this is what appears and I suspect is the cause of this problem, because all other websites are working: Priority: Notice Category: Network Access Message: TCP handshake violation detected; TCP connection dropped Source: X.Y.Z.3, 51997, LAN (admin) Destination: 200.14.232.18, 443, WAN Notes: Handshake Timeout Where X.Y.Z.3 is my local IP. I've tried to change TCP Settings under Firewall option, and activated this options with no success: Enforce strict TCP compliance with RFC 793 and RFC 1122 and Enable TCP checksum enforcement I've also tried to find the MTU and at first I got: Packet needs to be fragmented but DF set But when I lower the value of ping -f -l to 1468 I got: Request timeout. Also I deactivate CFS in lan and wan zones. Nothing works. Can you please help me? Any Ideas?

  Read the article

• DD-WRT: DNSMasq expand-hosts not working

  - by Craig Walker

  I have a Linksys router running DD-WRT (Firmware: DD-WRT v24-sp2 (09/08/09) mini). I have it successfully resolving the DNS names for my DHCP-assigned systems, but only when I fully-qualify those domains. This is despite using the "expand-hosts" DNSMasq additional option, which is supposed to activate this precise function. Here's my dnsmasq.conf: interface=br0 resolv-file=/tmp/resolv.dnsmasq domain=example.com dhcp-leasefile=/tmp/dnsmasq.leases dhcp-lease-max=51 dhcp-option=lan,3,10.77.0.5 dhcp-authoritative dhcp-range=lan,10.77.0.100,10.77.0.149,255.255.0.0,1440m dhcp-host=00:1A:A0:1D:82:5A,astatichostname,10.77.1.40,infinite expand-hosts (FYI: example.com and astatichostname are placeholders for the real-deal names I use. My network uses 10.77.0.0/16; my router is on 10.77.0.5.) Results: > nslookup astatichostname 10.77.0.5 Server: 10.77.0.5 Address: 10.77.0.5#53 ** server can't find astatichostname: NXDOMAIN > nslookup astatichostname.example.com 10.77.0.5 Server: 10.77.0.5 Address: 10.77.0.5#53 Name: astatichostname.example.com Address: 10.77.1.40 Is there something else that could be tripping up expand-host in DNSMasq?

  Read the article

• DrayTek 2820 configuration using public IP addresses

  - by Kev

  I have a /29 range of public IP addresses assigned to me by my ISP. I'm trying to configure a SIP VOIP handset to register with my VOIP provider who recommend using public IP addresses rather than NAT. I have a DrayTek 2820 router flashed with the latest firmware and have configured my router as per DrayTek's FAQ at: How do I use a public subnet on the LAN (non-NAT operation ) ? My IP range is: xx.xx.94.16 -> xx.xx.94.23 This gives a usable range of: xx.xx.94.17 -> xx.xx.94.22 My router's public IP address is: xx.xx.94.17, the SIP VOIP handset is allocated xx.xx.94.18. I have a second internet connection and via that I can ping the handset. However for some reason I can't seem to get it to register with the provider. I tried adding a new Firewall filter to pass through from WAN to LAN: Source: ANY, Destination: xx.xx.94.18, UDP - Ports 1024 -> 65535 Out of interest I also tried opening port 80 to see if I could browse to the phone's admin web interface but no joy. I know that my ISP aren't blocking inbound service ports because I NAT Port Forwarded port 80 to one of my internal web servers and it rendered a test page I had set up. All the NAT settings are reset to factory defaults, i.e. there are no Port Redirection, DMZ Host, Open Ports or Address Mappings configured. The handset I'm using is a GrandStream GXP-2000. Is there anything else I should be doing?

  Read the article

• IPCop Packet Mangling

  - by Zenham

  I've found myself in a pickle replacing an old firewall for a client this afternoon. I'm configuring their new IPCop firewall (1.4.21), Zerina OpenVPN addon is installed. What I need to do: There are three network interfaces, currently set up as red (WAN), green (LAN, 192.168.20.0/24) and orange (remote network 10.1.20.0/24). The orange interface is a direct fiber link to another organization. Simple description: Traffic and networks appear to be properly configured at this point, but I have many (150+) specific IPs on the LAN which, when accessing the resources on the 10.1.20.x network, need to be mangled to appear to be coming from the 10.1.20.0/24 network (and return traffic properly delivered). The routing on the far side was configured earlier and should be fine, but I need to redirect any packets coming across destined for those IPs to end up at their proper destination. The addressing is fixed and predictable (ie. 192.168.20.125 - 10.1.20.125). I need to insert whatever rules I have into the IPCop ruleset through /etc/rc.local I know, I'm just not sure about how I should structure this. There's CUSTOMOUTPUT and CUSTOMINPUT targets, both which currently just consist of the single rule redirecting packets to the OVPNOUTPUT/OVPNINPUT targets, so I'm guessing I should insert a rule matching outbound packets destined for the 10.1.20.x network and redirecting to a new target (maybe called TO-ORANGE) and a rule at the top of CUSTOMINPUT which redirects to a FROM-ORANGE target. Under those targets, I would have rules which do the IP matching and mangling. Am I approaching this right? If so, I'm not very familiar with mangle, and would appreciate seeing examples of how to write that source-IP rewrite. If not, how would you suggest doing this? TIA! edit: I notice additionally that the nat table has CUSTOMPREROUTING and CUSTOMPOSTROUTING targets, I guess I could alternatively post the rules in there....

  Read the article

• Windows Server 2008 DHCP with RRAS

  - by Guillermo Prandi

  I have a Windows Server 2008 R2 which is a member of a domain, but is placed in a remote location. The server is directly connected to Internet. Clients need to access a particular insecure TCP service in this server (ports 9730 and 9731). Since clients have dynamic IP addresses I cannot know in advance, I thought it would be nice to have them connected through a VPN in order to access the insecure service, but ONLY to access that service, like this: Client ------> VPN TUNNEL ------> (Insecure service at Server) | \----> (Normal internet access) I'd enable the insecure ports in the firewall only from VPN accesses. For this I configured RRAS in the server and gave it a static IP address range (172.19.1.2 through 172.19.1.254) to serve the clients. First I thought I could use DHCP to assign the addresses, but I cannot use DHCP in my LAN connection (not allowed by the hosting service). I tried configuring DHCP binding it to a Microsoft Loopback Adapter, but that's not supported as a DHCP source by RRAS. What I want to accomplish is to send specific DHCP options to the client (network mask, routing table, etc.). In particular: Prevent the client from having the server as default router (without changing the client's "use default gateway in remote network"). Have it as a route for the server's internal RRAS address only (172.19.1.1). Prevent the client from using a 255.255.0.0 mask for the 172.19.x.x network (a 255.255.255.0 mask would be better). Can I do that with RRAS only? How? Currently, the only solution I can think of is to use DHCP in the LAN adapter, but filter DHCP packets so they don't reach the provider's network. However, I'm not sure if that will work. Any suggestions are welcomed! Guille

  Read the article

• Multiple public IPs through DD-WRT without 1-to-1 NAT

  - by Stephen Touset

  I've done a search here and wasn't able to find anything relevant to my situation. I apologize in advance if I've missed an existing post on the topic. Our ISP has provided us with 6 static IP addresses. We are currently using two of them (plus one for the Comcast-provided router). One of the static addresses routes to our internal network, and the other goes to our VOIP phone system. Unfortunately, the Comcast machine doesn't support QoS, so our VOIP calls have been choppy. We plan to put the Comcast-provided router into bridge mode and replace it with an ASUS RT-N16 running DD-WRT. However, I'm unsure how to set up DD-WRT to function similarly to our existing Comcast router. The Comcast router's WAN IP is the first of our static IP addresses. We did not need to provide an internal LAN IP address — simply connecting machines that use our other public addresses to the LAN ports on the Comcast router is enough for it to route between the connected machines and our internet connection. Is there a way to do a similar setup through the DD-WRT? Thanks in advance.

  Read the article

• Centos IPTables configuration for external firewall

  - by user137974

  Current setup Centos which is a Web, Mail (Postfix,Dovecot), FTP Server and Gateway with public ip and private ip (for LAN Gateway). We are planning to implement external firewall box and bring the server to LAN Please guide on configuring IPTables... Unable to receive mail and outgoing mail stays in postfix queue and is sent after delaying... The local ip of the server is 192.168.1.220 iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP incoming HTTP iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 443 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 443 -m state --state ESTABLISHED -j ACCEPT outgoing HTTP iptables -A OUTPUT -o eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT FTP iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 21 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 1024:65535 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 1024:65535 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT SMTP iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 25 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 1024:65535 -d 0/0 --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --sport 25 -d 192.168.1.220 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT POP3 iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 110 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 110 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT

  Read the article

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

• DNS Server on Fedora 11

  - by Funky Si

  I recently upgraded my Fedora 10 server to Fedora 11 and am getting the following error in my DNS/named config. named[27685]: not insecure resolving 'fedoraproject.org/A/IN: 212.104.130.65#53 This only shows for certain addresses some are resolved fine and I can ping and browse to them fine, while others produce the error above. This is my named.conf file acl trusted-servers { 192.168.1.10; }; options { directory "/var/named"; forwarders {212.104.130.9 ; 212.104.130.65; }; forward only; allow-transfer { 127.0.0.1; }; # dnssec-enable yes; # dnssec-validation yes; # dnssec-lookaside . trust-anchor dlv.isc.org.; }; # Forward Zone for hughes.lan domain zone "funkygoth" IN { type master; file "funkygoth.zone"; allow-transfer { trusted-servers; }; }; # Reverse Zone for hughes.lan domain zone "1.168.192.in-addr.arpa" IN { type master; file "1.168.192.zone"; }; include "/etc/named.dnssec.keys"; include "/etc/pki/dnssec-keys/dlv/dlv.isc.org.conf"; include "/etc/pki/dnssec-keys//named.dnssec.keys"; include "/etc/pki/dnssec-keys//dlv/dlv.isc.org.conf"; Anyone know what I have set wrong here?

  Read the article

• Is there a reason to use internal DNS over 8.8.8.8 ?

  - by skylarking

  I've inherited a LAN where there is really no name resolution being done for local resources... i.e. all users enter IP addresses manually to access printers and network shares. There are no LDAP servers or domains either....workstations simply connect to the network without authentication. DHCP is handled via a core switch... And DNS settings are also handed out by this same core switch. Currently, the DNS assignments are as such, and in this order: 10.1.1.50 / old Pentium III Windows 2003 box running DNS service- 128 MB RAM 169.200.x.x / ISP 4.2.2.2. / the well known public one There a couple thousand clients on the LAN....and most of the activity is web browsing ( this is an educational setting ). First of all, the server seems woefully underpowered for this task...yet there is virtually no slowness when web surfing by clients.... How much horsepower should a heavily used DNS server have ? I have also heard using 4.2.2.2 is a bad idea .... since it has been so overused... Finally, wouldn't it make sense to have a robust external DNS server listed first? ( Google's 8.8.8.8 would seem to be a logical candidate )

  Read the article

• How to set up IP forwarding on Nexenta (Solaris)?

  - by Gleb

  I am trying to set up IP forwarding on my Nexenta box: root@hdd:~# uname -a SunOS hdd 5.11 NexentaOS_134f i86pc i386 i86pc Solaris The box has 2 network interfaces: root@hdd:~# ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g1: flags=1001100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4,FIXEDMTU> mtu 1500 index 2 inet 192.168.12.2 netmask ffffff00 broadcast 192.168.12.255 ether 68:5:ca:9:51:b8 myri10ge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 9000 index 3 inet 10.10.10.10 netmask ffffff00 broadcast 10.10.10.255 ether 0:60:dd:47:87:2 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 192.168.12.0 is my normal LAN with 192.168.12.1 being the firewall/gateway 10.10.10.0 is a separate LAN for iSCSI (with no internet access) I want to set up IP forwarding so that a computer on 10.10.10.0 will be able to access the internet by using 10.10.10.10 as a gateway (I don't need any port forwarding) I have turned on IP forwarding: root@hdd:~# routeadm Configuration Current Current Option Configuration System State --------------------------------------------------------------- IPv4 routing disabled disabled IPv6 routing disabled disabled IPv4 forwarding enabled enabled IPv6 forwarding disabled disabled Routing services "route:default ripng:default" Routing daemons: STATE FMRI disabled svc:/network/routing/rdisc:default disabled svc:/network/routing/route:default disabled svc:/network/routing/legacy-routing:ipv4 disabled svc:/network/routing/legacy-routing:ipv6 disabled svc:/network/routing/ripng:default online svc:/network/routing/ndp:default But when I dry to start ipnat, I get an error: root@hdd:~# ipnat -CF -f /etc/ipf/ipnat.conf ioctl(SIOCGNATS): I/O error Here is the config: root@hdd:~# cat /etc/ipf/ipnat.conf #!/sbin/ipnat -f - # map e1000g1 10.10.10.10/24 -> 192.168.12.2/32 So the question is how to fix this.. Thanks in advance!

  Read the article

• Opening and Testing Ports on Modem > Router Connection

  - by JakeTheSnake

  Working off of my last question, I can access my server's FTP over the LAN but not over the internet. I'm using Filezilla on port 666. My router/modem configuration is as such (similar to other post): 1) Modem connects to WAN 2) WAN port on modem connects to LAN port on Router 3) Modem internal IP address is 192.168.0.254 4) Router internal IP address is 192.168.0.1 5) Modem has DHCP turned OFF 6) Router has DHCP turned ON 7) Router is running Tomato firmware and it's set as 'Router' (not 'Gateway') 8) The internet is working (just had to say that) I've set up port forwarding both on the modem and router - both route port 666 to the IP address of 192.168.0.3 (TCP); that is the IP address of the server which has FileZilla running. I don't know if that's hindering anything but I've also tried it with just the modem and just the router...same result. I've also tried setting the server to be DMZ (both on router and modem). Neither router nor modem have anything in their logs about denying inbound traffic on port 666 so my ability to troubleshoot stops there. I've tried contacting my ISP (Telus, running on mobility plan...it's a "Smart" Hub) but they weren't much help. They said they only block port 25 and 80 and maybe a few others, but not most ports. I test whether or not the port is open by going to canyouseeme.org - I don't know whether or not that would produce a 'connection refused' result just based on the fact that the FTP requires a login...I'm not well versed on this matter. FWIW, sometimes I get a 'connection refused' error on canyouseeme.org but mostly it's 'connection timed out'. I don't know what else to do at this point.

  Read the article

• simple network between xp & 7 with cross cable problem...

  - by LostLord

  hi my dear friends : i have a simple network between xp & 7 windowses with cross cable (2 pc home)... ===================================================================== the one with 7 is mother and have 2 lan device (onboard + pci) A. onboard is like this when u go to tcp/ip v4 properties:(4 adsl internet) obtain an ip... preferred dns server : 81.91.129.67 alternate dns server : 4.2.2.4 shared...no permission 4 change so every thing is ok for internet on windows 7. B. the other lan pci card that is connected to pc with xp is like this : 192.168.2.11 255.255.255.0 0.0.0.0 empty empry computer name : cougar workgroup : nethome homeNetwork is disabled (i think that is 4 2 pc's with 7 os not xp) every thing is off in network options except file & printer sharing in public area ===================================================================== pc with xp os is like this : 192.168.2.12 255.255.255.0 192.168.2.11 (mean gateway) 4.2.2.4 8.8.8.8 computer name : tiger workgroup : nethome ===================================================================== at last my little net is ok... mean both have internet , both can see each other by their ip (\\192.168.2.11 or \\192.168.2.12) my problem is when in pc with xp type \\cougar it shows an error about network path! but in pc with 7 \\tiger works perfec. what is the problem in system with xp ? in few days ago this network was ok (search by computer name) when both os were xp , so there is no problem with my cable or devices. another problem is i can not find tiger in my network list in 7 pc \ why? is something wrong with my network? thanks 4 future advance best regards

  Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >