Search Results

Search found 11986 results on 480 pages for 'desktop'.

Page 452/480 | < Previous Page | 448 449 450 451 452 453 454 455 456 457 458 459  | Next Page >

• Trouble connecting a Ubuntu system to IPv6 tunnel over NAT

  - by John Millikin

  I'm trying to set up an IPv6 tunnel, via Hurricane Electric's tunnel-broker service. I've configured my system using their example commands: # $ipv4a = tunnel server's IPv4 IP # $ipv4b = user's IPv4 IP # $ipv6a = tunnel server's side of point-to-point /64 allocation # $ipv6b = user's side of point-to-point /64 allocation ip tunnel add he-ipv6 mode sit remote $ipv4a local $ipv4b ttl 255 ip link set he-ipv6 up ip addr add $ipv6b dev he-ipv6 ip route add ::/0 dev he-ipv6 And have configured my desktop to be in my NAT router's DMZ. The router is running Tomato firmware. But I can't ping any IPv6 services: $ ping6 -I he-ipv6 '2001:470:1f04:454::1' PING 2001:470:1f04:454::1(2001:470:1f04:454::1) from 2001:470:1f04:454::2 he-ipv6: 56 data bytes From 2001:470:1f04:454::2 icmp_seq=1 Destination unreachable: Address unreachable From 2001:470:1f04:454::2 icmp_seq=2 Destination unreachable: Address unreachable I can ping my local address: $ ping6 -I he-ipv6 '2001:470:1f04:454::2' PING 2001:470:1f04:454::2(2001:470:1f04:454::2) from 2001:470:1f04:454::2 he-ipv6: 56 data bytes 64 bytes from 2001:470:1f04:454::2: icmp_seq=1 ttl=64 time=0.037 ms 64 bytes from 2001:470:1f04:454::2: icmp_seq=2 ttl=64 time=0.039 ms I don't know much about routing, but results I found online suggested the output of ip -6 route and ip addr could be useful: $ ip -6 route 2001:470:1f04:454::/64 via :: dev he-ipv6 proto kernel metric 256 mtu 1480 advmss 1420 hoplimit 4294967295 fe80::/64 dev virbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 via :: dev he-ipv6 proto kernel metric 256 mtu 1480 advmss 1420 hoplimit 4294967295 default dev he-ipv6 metric 1024 mtu 1480 advmss 1420 hoplimit 4294967295 $ ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 100 link/ether 00:1c:c0:a1:98:b2 brd ff:ff:ff:ff:ff:ff inet 192.168.1.10/24 brd 192.168.1.255 scope global eth1 inet6 fe80::21c:c0ff:fea1:98b2/64 scope link valid_lft forever preferred_lft forever 3: virbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 36:4c:33:ab:0d:c6 brd ff:ff:ff:ff:ff:ff inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0 inet6 fe80::344c:33ff:feab:dc6/64 scope link valid_lft forever preferred_lft forever 4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 00:76:62:6e:65:74 brd ff:ff:ff:ff:ff:ff 5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 7e:29:5e:7c:ba:93 brd ff:ff:ff:ff:ff:ff 6: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 7: he-ipv6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN link/sit 24.130.225.239 peer 72.52.104.74 inet6 2001:470:1f04:454::2/64 scope global valid_lft forever preferred_lft forever inet6 fe80::1882:e1ef/128 scope link valid_lft forever preferred_lft forever

  Read the article

• VPN IP Routing - slow connections

  - by dannymcc

  UPDATE: Router error logs show: LCP Time-out 0 I'm not sure how to correct this. The Lan-to-Lan profiles are set to -1 Idle Timeout (for the remote branch). I have a PPTP VPN running between two Draytek 2820 routers. They are setup that one dials out to the other one. Main Practice - 192.168.1.0/24 Branch - 192.168.3.0/24 I have then set (on the Branch) router the following route: 192.168.1.0/24 If I then request a server running on 192.168.1.1 from the Branch, it correctly routes through VPN tunnel. If I request the branch server at 192.168.3.1 it correctly routes to the local server without using the VPN tunnel. I have temporarily disabled the firewall on both routers, and made sure that QoS is disabled. The Main Practice internet connection is ~30mb down / ~10mb up, and the Branch connection is ~5mb down / ~2mb up. Anything over the VPN tunnel runs pretty slowly (VNC, Remote Desktop and Terminal Emulators). However, if I dial using the Windows VPN wizard, creating a connection from the laptop to the Main Practice - everything runs quickly. I'm looking for possible causes, and/or ways of further diagnosing the issue. Any help would be greatly appreciated! UPDATE: In summary, when I connect within the Branch and try and access a host that's within the Main Practice it works, but slowly. If I then dial the VPN on my Windows 7 laptop whilst still connected to the Branch network, it's fast. Main Practice Branch Practice Routing Table from Branch Router Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 126.256.126.103 WAN2 C~ 192.168.1.99/ 255.255.255.255 directly connected VPN-1 S~ 192.168.1.0/ 255.255.255.0 via 192.168.1.99 VPN-1 S~ 192.168.2.0/ 255.255.255.0 via 192.168.1.99 VPN-1 C~ 192.168.3.0/ 255.255.255.0 directly connected LAN2 C 126.256.126.103/ 255.255.255.224 directly connected WAN2 Routing Table from Main Practice Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 81.139.64.1, WAN2 S 81.137.176.1/ 255.255.255.255 via 81.137.176.1, WAN2 * 81.139.64.1/ 255.255.255.255 via 81.139.64.1, WAN2 C~ 192.168.1.204/ 255.255.255.255 is directly connected, VPN C~ 192.168.1.0/ 255.255.255.0 is directly connected, LAN S~ 192.168.2.0/ 255.255.255.0 via 192.168.1.204, VPN S~ 192.168.3.0/ 255.255.255.0 via 192.168.1.203, VPN Connection Details (from Branch Router) Connection Details (from Main Practice Router) IPERF.exe Output

  Read the article

• Installing drivers for switchable graphics

  - by Anonymous

  I recently bought a laptop that came with Windows 7 64-bit installed. I have some older (16-bit and 32-bit) software that doesn't work with 64-bit Windows, but works just fine with 32-bit. Since I also wanted to get rid of all of the pre-installed spam, I decided to wipe the hard drive and install a fresh copy of Windows 7 32-bit. I can't get the graphics cards working. This laptop uses switchable graphics, an Intel card and a Radeon card. I first tried installing this driver from Intel, which works for the Intel card. Of course, the Radeon card doesn't work with this driver and I need it for some of the newer games I have. I also tried this driver. Windows's device manager will recognize the Radeon card, but it will still use the Intel card. Also, even though that package says it contains the Intel driver, the Intel card still isn't properly recognized by Windows (leaving me with a nasty 800x600 resolution). On top of that, the Catalyst Control Center won't open (saying "The Catalyst Control Center is not supported by the driver version of your enabled graphics adapter") I tried installing HP's driver then installing Intel's driver on top of it. Device manager will then recognize both graphics cards properly. However, the laptop still uses the Intel card. The CCC still won't start (saying the same thing as before) and I can't find any of 'switching' graphics cards. Before formatting, I could right-click the desktop and click "Configure Switchable Graphics" This option hasn't been in the context menu regardless of what driver(s) I've installed. After some research, I found out that this menu entry runs the command "cli.exe Start PowerXpressHybrid" I've tried manually running this command, but I get the same unsupported message from CCC. So, does anyone know how I can get this working? I would like to be able to switch between the Intel and Radeon. But, if there's some way to disable the Intel and use only the Radeon, that would be fine I dual-boot with Linux (framebuffer uses the Intel, haven't even tried getting X set up yet) Here's the output of lspci # lspci -v | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller]) 01:00.0 VGA compatible controller: ATI Technologies Inc NI Seymour [AMD Radeon HD 6470M] (prog-if 00 [VGA controller]) The laptop is a HP Pavilion g6t-1d00. HP doesn't support installing anything but Windows 7 64-bit, so calling tech support isn't an option. Thanks for any help UPDATE: I finally got it working. After a fresh install of Windows 7, I installed the HP driver (the one linked above). Then, there's an optional Windows update I installed (don't remember the exact name, but it'll stick out). After that, graphics switching works just like it's supposed to. Moab, thanks anyways for your help

  Read the article

• Dynamic DNS with Comcast

  - by colithium

  I've just recently moved across town. Previously, I had Dynamic DNS set up so I could remotely connect to my desktop (primarily to use TightVNC). My ISP was Comcast and I'm in the Denver, Colorado area. Currently, I'm still with Comcast and still in Denver. My router connects to the internet just fine and my Dynamic DNS record over at DynDNS did get updated with my router's current external IP address. So my router, DynDNS, and public DNS records all agree what my IP address is. However, I can't actually connect to anything from the outside world. My trace route to Google looks something like: Tracing route to google.com [74.125.19.147] 1 3 ms 1 ms 1 ms 192.168.1.1 (this is the internal IP address of my router) 2 * * * Request timed out. 3 9 ms 8 ms 10 ms te-8-2-ur02.wheatridge.co.denver.comcast.net [68.85.221.177] 4 12 ms 12 ms 19 ms te-0-8-0-2-ar02.aurora.co.denver.comcast.net [68.86.103.97] 5 16 ms 13 ms 11 ms pos-0-3-0-0-cr01.denver.co.ibone.comcast.net [68.86.91.1] 6 28 ms 28 ms 27 ms pos-0-9-0-0-cr01.dallas.tx.ibone.comcast.net [68.86.85.174] 7 29 ms 27 ms 28 ms pos-0-1-0-0-pe01.1950stemmons.tx.ibone.comcast.net [68.86.86.94] 8 66 ms 108 ms * 75.149.231.70 9 65 ms 68 ms 93 ms 72.14.233.77 10 67 ms 66 ms 66 ms 72.14.233.111 11 67 ms 67 ms 69 ms 216.239.43.144 12 68 ms 71 ms 73 ms 209.85.249.30 13 66 ms 66 ms 68 ms nuq04s01-in-f147.1e100.net [74.125.19.147] This is what the trace route looks like from an outside source to my DynDNS domain name: traceroute to 98.245.67.65 (98.245.67.65) 1 illuminati-130 138.67.130.61 2 138.67.63.253 138.67.63.253 3 vermiculite 138.67.253.20 4 csm-ct-gw 138.67.253.244 5 138.67.253.2 138.67.253.2 6 ge-7-24-ar01.denver.co.denver.comcast.net 68.86.128.17 7 te-0-4-0-0-ar02.denver.co.denver.comcast.net 68.86.179.21 8 te-9-3-ur01.wheatridge.co.denver.comcast.net 68.86.103.18 9 * * * {Times Out} Now my guess is, whatever is sitting just beyond my router (what the modem connects to) is gumming things up. Even though the routes aren't EXACTLY the same, that appears to be the spot that the trace route either stops or doesn't get a response. My question is, for Comcast networks (particularly in Denver), what would be the device that typically sits there? Is there anything I can do about it? That device seems to not respond to PING but does forward it along when I'm going outwards. But it looks like it eats it when the request is coming in. It's hard to prove that from these logs but I'm assuming that's the case because my router used to accept connections from the outside and I haven't changed anything on it.

  Read the article

• OS X: Finder error -36 when using SMB shares on a Samba server bound to AD

  - by Frenchie

  We're looking at deploying SMB homes on Debian (5.0.3) for our mac clients rather than purchasing four new Xserves. We've got our test servers built and functioning properly. Windows clients behave perfectly, but we've run into an issue with OS X (10.6.x and 10.5.x). We're going this route instead of Windows file servers due to a whole bunch of other issues that arise when going that way. Specifically, when mounting a SMB share with unix extensions switched on and the remote server bound to AD, the finder cannot save files on the share, instead touching the file and then bombing out with a -36 IO error, folder creation is fine. Copying files in the terminal behaves fine and the problem seems to be limited to the finder. The issue arises (I think) as the remote UID/GID is passed across when using unix extensions. OS X uses its own winbind idmap (odsam) to work out the effective UID/GID from AD users and groups whilst we're using a rid map on the server. Consequently, there is a mismatch in ownership which the finder chooses to honour. How OS X appears to handle this is to use the remote uid and gid at the file permission level (see below) and then set an OS X acl granting the local uid/gid to have the appropriate permissions on the file. I think the finder touches the file (which the kernel allows because of the ACL) and then checks the filesystem perms and drops out with the IO error. On a Client fc-003353-d:homes2 root# ls -led test/ drwx------+ 2 135978 100513 16384 Feb 3 15:14 test/ 0: user:jfrench allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,writesecurity,chown,file_inherit,directory_inherit 1: group:ARTS\domain users allow 2: group:everyone allow 3: group:owner allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,writesecurity,chown,file_inherit,directory_inherit,only_inherit 4: group:group allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,writesecurity,chown,file_inherit,directory_inherit,only_inherit 5: group:everyone allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,writesecurity,chown,file_inherit,directory_inherit,only_inherit We've tried the following without any luck: Setting the Linux side file owner to match the OS X GID/UID Adding ACLs on the linux filesystem which grant the OS X GID/UID perms Disabling extended attributes Setting steams=no in /etc/nsmb.conf on the client We're currently running a workaround which is to just turn off unix extensions which forces the macs to just mount the share as the local user with u=rwx perms. This works for most things but is causing a few apps that expect certain perms to break in subtle ways. Worst case scenario is that we'll continue running in this way but we would like to have the unix extensions on. Regards. Relevant SMB config below: [global] workgroup = ARTS realm = *snip* security = ADS password server = *snip* unix extensions = yes panic action = /usr/share/panic-action %d idmap backend = rid:ARTS=100000-10000000 idmap uid = 100000-10000000 idmap gid = 100000-10000000 winbind enum users = Yes winbind enum groups = Yes veto files = /lost+found/aquota.*/ hide files = /desktop.ini/$RECYCLE.BIN/.*/AppData/Library/ ea support = yes store dos attributes = yes map system = no map archive = no map readonly = no

  Read the article

• An alternative to Google Talk, AIM, MSN, et al [closed]

  - by mkaito

  I'm not entirely sure whether this part of stack exchange is the most adequate for my question, but it would seem to me that people sharing this kind of concern would converge either here, or possibly on a more unix-specific sub site. Either way, here goes. Background Feel free to skip to The Question, below. This should, however, help those interested understand where I'm coming from, and where I expect to get, messaging-wise. My online talking place-to-go has been IRC for the last fifteen years. I think it's a great protocol, and clients out there are very good. I still use, and will always continue to use IRC for most of my chat needs. But then, there is private instant messaging. While IRC can solve this with queries and DCC chats, the protocol just isn't meant to work too well on intermittent connections, such as a mobile device, where you can often walk around places with low signal. I used MSN for a while, but didn't like it. The concept was awesome, but I think Microsoft didn't get the implementation quite right. When they started adding all that eye candy, and my buddies started flooding me with custom icons and buzzing my screen to it's knees, I shut my account and told folks that missed me to just email or call me. Much whining happened, I got called many weird things for not using MSN, but folks eventually got over it. Next, Google Talk came along, and seemed to be a lot better than MSN ever was. The protocol was open, so I could use whatever client I felt a fancy for. With the advent of smart phones, I just got myself a gtalk client on the phone, and have had a really decent integrated mostly-universal IM solution. Over the last few months, all Google services have been feeling flaky. IMs will often arrive anywhere between twenty minutes and one hour after being sent, clients will randomly disconnect, client priorities seem to work sometimes, and sometimes just a random device of those connected will get an IM. I think the time has come to look for greener grass. The Question It's rather hard to put what I'm looking for into precise words. I guess I just want something that is kind of like MSN/Gtalk, but that doesn't let me down when I need it. IRC is pretty much perfect, but the protocol just isn't designed to work well on mobile devices. Really, at this point I'm considering sticking to IRC for desktop messaging, and SMS/email on the phone, but I hope that in this day and age there is something better out there.

  Read the article

• Ubuntu 12.04: apt-get "failed to fetch"; apt is trying to fetch via old static IP

  - by gabe

  Sample error: W: Failed to fetch http://security.ubuntu.com/ubuntu/dists/precise-security/universe/i18n/Translation-en Unable to connect to 192.168.1.70:8118: Now this was working just fine until I changed the IP this morning. I have the server set to a static IP of 10.0.1.70 and for years it has been 192.168.1.70 - the IP apt-get is trying to use right now. I use privoxy and tor thus the 8118 port. Like I said it all worked until I changed the static IP from 192.168.1.70 to 10.0.1.70. I was forced to do so because of router issues. (Long and involved story, I didn't really want to change the IP because I know something like this would happen.) The setup for TOR/Privoxy requires that has you point Privoxy at TOR via 127.0.0.1:9050. Then point curl, etc to Privoxy via $HOME/.bashrc. Typically you would set the listen to IP for Privoxy to 127.0.0.1 but if you want it accessible to the rest of the LAN you set the IP to the server's LAN IP. Which I did a long time ago and was working fine until this morning. I have changed all instances of 192.168.1.70 to 10.0.1.70 in both /etc/privoxy/config and $HOME/.bashrc. What makes this really strange for me is that curl is working fine. I curl icanhazip.com and voila I get a new IP every 10 minutes or so. I curl CNN.com and I get the short but sweet permanently moved to www.cnn.com message I expect. Firefox works fine. Ping works fine. And I've tested all of this via Remote Desktop over my LAN. So the connection appears to be fine for everything except apt. I've also rebooted hoping that would clear 192.168.1.70 from apt. So the connection to the internet and DNS aren't an issue for these programs. And they are, as far as I can tell, using Privoxy/TOR just fine. The real irony here is that I've tried to open up Privoxy to go to Ubuntu's servers directly without going through TOR to speed up the downloads from Ubuntu (did this months ago). So somewhere that I have not been able to find, apt has stored the IP 192.168.1.70. And 192.168.1.70 is no longer valid. Thanks for the help

  Read the article

• Ubuntu and Belkin N150 f6d4050 Wireless USB adapter v2

  - by Andrew

  I'm new to Ubuntu, and I'm trying to get my Belkin USB adapter to work. There are plenty of discussions out there already about this, but none really helped me out. Here's what I've done - Installed ndiswrapper Installed ndisgtk Installed the driver (rt2870.inf) via ndisgtk ndisgtk reported that the driver was installed and the hardware was present. The green light on the adapter is solid green, which I assume means that Ubuntu is aware of it's presence. However, when I click the little wireless symbol at the navigation bar, there's no option to choose my adapter (assuming that it's supposed to show up there...) My adapter version is F6D4050 - Where do I go from here? I'm a Ubuntu newb, so speak slowly. :P lsusb - andrew@ubuntu:~$ lsusb Bus 002 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 002 Device 002: ID 04f9:0229 Brother Industries, Ltd Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 050d:935b Belkin Components Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsmod - andrew@ubuntu:~$ lsmod Module Size Used by binfmt_misc 7960 1 fbcon 39270 71 tileblit 2487 1 fbcon font 8053 1 fbcon bitblit 5811 1 fbcon softcursor 1565 1 bitblit vga16fb 12757 0 vgastate 9857 1 vga16fb snd_cmipci 37557 2 snd_intel8x0 31155 2 snd_ac97_codec 125394 1 snd_intel8x0 ac97_bus 1450 1 snd_ac97_codec snd_mpu401 6875 0 snd_pcm_oss 41394 0 snd_mixer_oss 16299 1 snd_pcm_oss snd_pcm 87882 4 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_opl3_lib 10846 1 snd_cmipci snd_hwdep 6924 1 snd_opl3_lib snd_mpu401_uart 6857 2 snd_cmipci,snd_mpu401 snd_seq_dummy 1782 0 snd_seq_oss 31219 0 snd_seq_midi 5829 0 snd_rawmidi 23420 2 snd_mpu401_uart,snd_seq_midi snd_seq_midi_event 7267 2 snd_seq_oss,snd_seq_midi snd_seq 57481 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event nouveau 515227 2 ttm 60847 1 nouveau snd_timer 23649 3 snd_pcm,snd_opl3_lib,snd_seq snd_seq_device 6888 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq ns558 3704 0 ppdev 6375 0 drm_kms_helper 30742 1 nouveau joydev 11072 0 ndiswrapper 244768 0 gameport 10966 3 snd_cmipci,ns558 usblp 12407 0 asus_atk0110 10033 0 parport_pc 29958 1 serio_raw 4918 0 drm 199204 4 nouveau,ttm,drm_kms_helper i2c_algo_bit 6024 1 nouveau edac_core 45423 0 edac_mce_amd 9278 0 k8temp 3912 0 snd 71106 23 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_mpu401,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_hwdep,snd_mpu401_u art,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 8052 1 snd snd_page_alloc 8500 2 snd_intel8x0,snd_pcm i2c_nforce2 6099 0 lp 9336 0 parport 37160 3 ppdev,parport_pc,lp hid_logitech 8820 0 ff_memless 5109 1 hid_logitech ohci1394 30260 0 usbhid 41084 1 hid_logitech hid 83440 2 hid_logitech,usbhid usb_storage 49833 0 skge 41049 0 ieee1394 94771 1 ohci1394 sata_sil 8895 0 forcedeth 55592 0 sata_nv 23778 1 pata_amd 11962 1 floppy 63156 0

  Read the article

• Why is user asked to choose their workgroup?

  - by Clinton Blackmore

  We running Mac OS X Server 10.5.8 with Mac OS X 10.5.8 clients. Students use network logins to, well, log in. I've been asked to deny internet access to a specific user. I was told that a good way to do it is to create a user workgroup called "No Internet Access" and manage settings there. (Specifically, I told parental controls to allow access to no sites, and blacklisted all the installed web browsers). Now, when the user authenticates to log in, they are greeted with this dialog: Workgroups for <username> Grade 7 Students No Internet Access It is unlikely that the student would willing choose "No Internet Access" to be their base group. Looking in Workgroup Manager at the student's record, it shows their primary group ID is the grade 7 group, and "No Internet Access" is listed as another group they belong to. I looked at the managed preferences for all the computers pertaining to logins. They are set to their defaults. Specifically, the computer groups' preference for Logins - Access has the defaults: [unchecked] Ignore workgroup nesting [checked] Combine available workgroup settings Based on my reading of Tips and Tricks for Mac Administrators, this should be correct, the user should not be asked which group they belong to, and settings from all applicable groups should be applied. How can I achieve that result? Edit: I've decided to add some additional information from the Tips and Tricks for Mac Management White Paper (via Apple in Education, via the author's site). On page 21, it says: With Leopard MCX, workgroup preference settings are combined by default into a single set of values. This means that instead of having to choose between the Math, Science, or Language Arts workgroups when logging in, a user can just authenticate and be taken directly to the desktop. All the settings for each of those workgroups are composited together, providing you with all the Dock items and a composite of all the other settings. On page 40, an example is given in which settings are combined from different 'domains', one computer group, two (user) workgroups, and one individual user's settings. [When johnd logs into a leopard client,] the items staged in the Dock from left to right are: computer group, first workgroup alphabetically, second workgroup, user. Items within the workgroup are staged alphabetically. Nowhere is there an indication that groups are nested; indeed, I can see no sensible (non-flat) heirarchy for groups like Math, Science, and Language Arts. I strongly believe that there is a way to apply settings from two unrelated user workgroups such that a user of OS X 10.5.x or newer does not need to choose their workgroup. This is what I seek to achieve.

  Read the article

• Persistent Issues on small business network using Cisco 871W and Catalyst Express 500

  - by Ben Campbell

  Being the most qualified (read: still not qualified) to solve our persistant network issues, I've turned to serverfault for guidance. I've done some searching, reading related documentation on cisco.com and tried a bit of troubleshooting. Here is the config: 100mb synchronous connection from a business internet provider (tested multiple times at 100meg at the source) Cisco 871W wireless point & router is where the WAN connection starts (this serves all our wireless). The only wired connection in the 871W is the Catalyst switch listed below. Cisco Catalyst Express 500 (24TT) is where all the wired connections terminate. About 20 Windows workstations and servers (AD/Webservers only). Some services in EC2 including mail and other web servers/apps. I've been TOLD cabling internally should be gigabit-ready. Here are the problems: generally slow download rates from the internet to the desktop/laptop frequent "page cannot be displayed" errors in browsers-sometimes 3 or 4 reloads are necessary... often times CSS wont load or other content requiring the browser to connect to a different server. slow speed within the LAN from workstation to workstation copying files. I would expect extremely fast data transfer workstation to workstation / server to workstation in this simple network. Several things I need to admit: I'm not primarily a network guy. Funding is relatively low, I need to be the guy that finds the solution. I understand most of the terminology and most of the technology. Implementation is where I fail due to lack of experience. Getting to the point: I'm wondering whether experienced network admins think that our small network should be sufficiently served with our current hardware if configured properly... or if we should purchase new equipment and start fresh? If starting fresh is the plan, whatever that new equipment may be is a likely different question entirely. If I haven't provided enough information, I will happily do some troubleshooting and update with the results. I have experience using wireshark and some other tools. Please let me know what you think would be most helpful and thanks in advance. EDIT: I forgot to add that the Cisco applicance will not finish loading the SDM Express console. It hangs every time at the "populating modules... DHCP". It eventually crashes and closes. I've rebooted the hardware and this still happens.

  Read the article

• Cannot run a VM with more than three network interfaces with KVM

  - by Bostonvaulter

  I'm running KVM on top of Ubuntu 10.10 Server I can create VM's (Virtual Machine) and network interfaces fine but I cannot seem to add more than three network interfaces. As soon as I have a VM with four network interfaces it gets stuck on startup at the starting SeaBIOS page with this message: Starting SeaBIOS (version pre-0.6.1-20100702_143500-palmer) So far I've verified this with two VM's, a Ubuntu 10.10 desktop and a Vyatta router. The specific network hardware I assign to the VM's doesn't seem to matter. I'm trying to have one bridged interface and three private networks using Vyatta to route between them. Does anyone know why I can't run a VM with more than three network interfaces? Edit: Additionally the KVM thread responsible for the specific VM hangs using ~100% CPU (i.e. one core). Here's the command for the process that is hanging: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1,sockets=1,cores=1,threads=1 -name vyatta -uuid 6dff7c94-6810-423e-5fea-fec10da0e9b7 -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/vyatta.monitor,server,nowait -mon chardev=monitor,mode=readline -rtc base=utc -boot c -drive file=/home/rams/virtual-machines/vyatta.img,if=none,id=drive-ide0-0-0,boot=on,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -device rtl8139,vlan=0,id=net0,mac=00:54:00:be:cc:4b,bus=pci.0,addr=0x3 -net tap,fd=97,vlan=0,name=hostnet0 -device rtl8139,vlan=1,id=net1,mac=52:54:00:da:59:ed,bus=pci.0,addr=0x5 -net tap,fd=98,vlan=1,name=hostnet1 -device rtl8139,vlan=2,id=net2,mac=52:54:00:ce:22:b6,bus=pci.0,addr=0x6 -net tap,fd=99,vlan=2,name=hostnet2 -device rtl8139,vlan=3,id=net3,mac=52:54:00:1e:bc:46,bus=pci.0,addr=0x7 -net tap,fd=101,vlan=3,name=hostnet3 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -vnc 127.0.0.1:0 -k en-us -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 Edit: I've also found an error in dmesg that might be related (it also shows up when running virtd in verbose mode): 14:47:24.399: warning : qemudParsePCIDeviceStrs:1422 : Unexpected exit status '1', qemu probably failed I've also tried disabling app armor but that doesn't seem to make a difference.

  Read the article

• Need help making an ODBC MySQL Connection

  - by Andy Moore

  Short Version: How do I connect from PowerShell to an ODBC 5.1 MySQL Driver? I can't seem to find any connection strings that accurately have a "Provider" field for this particular instance. (See bottom of this question for examples/errors) ===== Long Version: I'm not a server guy, and I've been handed the task of setting up PowerGadgets on our network. I have a MySQL server running on a Linux box, that is configured for remote access and has a user defined for remote access as well. On my windows desktop PC, I have PowerGadgets installed. I installed the MySQL ODBC 5.1 connector, and went to Control Panel Data Sources and set up a User DSN connection to the database. The connection, user, and pass seem to be correct because it lists the tables of the database in my windows control panel. Where I'm running into trouble is in 3 places in PowerGadgets: When selecting a data source, I can select "SQL Server". Inputting the servers IP address does not work and I can't get this option to work at all. When selecting a data source, I can select "OleDB". This screen has a wizard on it, that appears to populate all the correct information (including database table names!) for me. "Test Connection" runs great. But if I try to complete the wizard, I get the error "The .NET Framework data provider for OLEDB does not support the MS Ole DB provider for ODBC Drivers." When selecting a data source, I can select "ODBC". This screen does not have a wizard and I cannot figure out a "connection string" that works. Typically it will respond with the error "The field 'Provider' is missing". Googling ODBC connection strings doesn't reveal any examples with a "provider" field and have no idea what to put in here. The connection string (for #2) above contains "SQLOLEDB" as a provider, and upon inputting that value into this connection string I get the same connection error that #2 gets. I believe I can solve my problems by figuring out a connection string for #3 but don't know where to get started. (PowerGadgets also allows for PowerShell support but I believe I will run into the same problem there) == Here's my current PowerShell connection that doesn't work: invoke-sql -connection "Driver={MySQL ODBC 5.1 Driver};Initial Catalog=hq_live;Data Source=HQDB" -sql "Select * FROM accounts" Spits back the error: "Invoke-Sql : An OLE DB Provider was not specified in the ConnectionString. An example would be, 'Provider=SQLOLEDB;'. == Another string that doesn't work: invoke-sql -connection "Provider=MSDASQL.1;Persist Security Info=False;Data Source=HQDB;Initial Catalog=hq_live" -sql "select * from accounts" And the error: The .Net Framework Data Provider for OLEDB (System.Data.OleDb) does not support the Microsoft OLE DB Provider for ODBC Drivers (MSDASQL). Use the .Net Framework Data Provider for ODBC (System.Data.Odbc).

  Read the article

• chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

  - by Zian Choy

  When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

  Read the article

• Setting Timeouts: SQL Server 2008/IIS 7.5

  - by Julie

  We have recently migrated from a Win 2003/SQL Server 2000 system to Win 2008 64 bit R2, SQL Server 2008 R2. Our websites are in classic asp, and this can't be changed to another scripting language at this time. On the old server, if I got stuck in some kind of endless loop, the page would throw an error. On the new server, I have a page that has some sort of looping problem, that even though the SQL SP is called only once (and runs fine run as a query on the server) it pegs SQL server and therefore locks all of our websites. I'll get my code figured out, no biggie. But I need to make sure the server times out when this happens. (The page I'm working on runs fine with certain instances of the query, and locks with others using a different query variable. I can't have something like that sneak up on me on a page I haven't touched for three years.) I can't figure out how an SP that runs once on the server, from an ASP page, is tying up SQL server this way. It's obviously some sort of a timeout issue, but I can't figure out where/which timeout values to change. I actually have to remote desktop to the server and kill the process in SQL server. I'm afraid I'm a generalist, and server management is not my thing, even though it's my responsibility, so I am almost certain to have questions about any answer that I receive. How can I track this down? What settings do I need to change? More info: It's not SQL Server On our test site, I created an ASP file that just did an endless loop (do while 1=1) and had the same problem - the other websites wouldn't load - without SQL server being involved. So I think the reason the process was hanging is that the page wasn't timing out as it should, and so the connection to SQL was never closed. Killing the process in SQL server would reset the page somehow. For my intentional endless loop, I had to refresh the app pool to get rid of it. This points more to either IIS or the ASP settings. The ASP timeouts are set to whatever the default were when the server was first loaded. I still can't figure out why one file is locking up all websites, though. Again, that didn't happen on the old server.

  Read the article

• OS X Snow Leopard 10.6 Refuses to Load Websites the first time intermittently

  - by Brandon

  Many times when I am browsing the web, Snow Leopard will sit and load a site for 20 seconds or more, until it times out and says it cannot be displayed. If I refresh, it loads RIGHT away, every time. The issue is intermittent but happens from once every couple of days to a few times a day. So the long and short of it is this: Aluminum MacBook (Non-Pro) 2.4GHz Core2Duo, 4GB DDR3 I am using 10.6.6 but I have had this issue since 10.6.0 It happens in Firefox, Chrome, and Safari I have flushed my DNS (using the command 'blablabla flush') I am using custom DNS servers which I hoped would fix it but it had no effect* I am running Apache currently but haven't been for most of the time I've reformatted multiple times, always experiencing the issue I am on Cox cable internet, with a Motorola Surfboard & a Belkin F6D4230-4 v1 (Pre?) N wireless router. I've put the router in G only & N only & G+N to no effect It seems to be domain dependant as I can sometimes load the Google cache right away, and sometimes other sites will load but Google will refuse My Powerbook G4 with Leopard, other Windows XP laptops, & my wired Win7 desktop do not suffer from the issue. *I recently started using these to escape the awful Cox redirect page on timeouts I'm almost positive the issue has happened on other networks but I can't recall a specific instance (I have a terrible memory). The problem is intermittent and fixable enough (I just have to wait until it times out and hit refresh one time) but incredibly annoying since I'm constantly reading documentation from a large variety of sites. EDIT: To clarify, this happens with ALL sites, not only specific sites. I haven't been able to detect any pattern to the failures, but one day Google.com will refuse to load while reddit.com will, and the next day vice versa. Keep in mind that waiting for a timeout and hitting refresh loads the page right away, every time. If I don't wait for the timeout, opening more links, hitting refresh, and clicking the link a billion times have no effect. It seems to be domain neutral, affecting sites seemingly at random. It doesn't seem to have anything to do with connection inactivity either, because I will be SSHed into different servers, uploading files, browsing, downloading, etc, and it will just quit loading Jquery.com (for example) until I sit and wait for a timeout. /EDIT This is my last resort. Please, someone, tell me what is happening. Thank you.

  Read the article

• USB ports causing Wireless and Mobile Phone tethering drop out

  - by chrolli

  I have a problem with my USB ports and I can't seem to pinpoint the problem. I'm hoping that I can get some idea as to how to troubleshoot my problem. Problem description: I recently bought a USB Wireless Adapter in order to connect my Desktop PC to the WLAN. The dongle keeps dropping off connection regularly on average once a minute. And the connection is slow. What I've tried: I installed a network scanner to determine signal strength. The PC/adapter combo is getting about 70% signal strength. I have a laptop that has an internal Wireless adapter. I moved the laptop near the location of the PC. The signal strength was above 90%. I installed the USB adapter on the laptop. I placed the laptop near the location of the PC. The signal strength was above 80%. And there is no drop out issue. I've isolated the problem to be on the PC. I used internet tethering on my mobile phone in order to test the USB ports. I get the same problem, themobile phone keeps dropping in and out. I plugged the adapter and phone on all USB ports, and it is still dropping out on all ports. I've isolated the problem to be the Motherboard, USB hub. I updated the BIOS, and USB driver. Still dropping out. I noticed that when I used the mobile phone tethering method, the phone (iphone 5) is guarenteed to drop out and does not appear to charge if I jiggle the the 8-pin connector on the base of the phone. If I push the pin tightly on the phone, the phone starts charging, as soon as I let go, it stops and drops out from the PC. This is strange because this doesn't happen when it is plugged to the powerboard. Which means that the 8 pin connector is fine. I'm not sure what the problem is. I assume that it is to do with the USB ports not supplying enough power which in turn causes the devices to intermittently drop out. The reason I say this is because the USB cable works fine when plugged into a powerboard with enough power supplied to the phone. Only when it is plugged into the USB port on the PC, does it drop out. My motherboard is Asus P8z68-v le. My Wireless adapter is the D-link DWA131. I can't seem to find any settings in the BIOS to increase the south bridge voltage so as to supply more power to the USB ports. Although this problem only occurs when I'm trying to hook up to a device supplying internet connection. My USB HDD, Flash drives, and Mouse and Key are working fine! Any suggestions please?

  Read the article

• How to reference a Domain Controller out of the Local Network?

  - by Adrian

  We have multiple servers scattered over different hosting providers. For learning, experimenting and, ultimately, production purposes, I set one of them as a Domain Controller. That went well, most of our services are now authenticating via AD, which helps us a lot. What I want to do now is to simplify the authentication for the multiple servers, by making each of them look at the Domain Controller. This way, our Devs can log into (Remote Desktop) the multiple servers with the same credentials from AD. I know I have to configure each server to look at the Domain Controller. But when I try to add the Domain Controller to the Computer, it cannot find it, although the Domain Controller address is a valid, reachable internet sub-domain (as in "ad.ourcompany.com"). This is the detailed error message: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. The following error occurred when DNS was queried for the service location (SRV) resource record used to locate an Active Directory Domain Controller for domain ad.ourcompany.com: The error was: "DNS name does not exist." (error code 0x0000232B RCODE_NAME_ERROR) The query was for the SRV record for _ldap._tcp.dc._msdcs.ad.ourcompany.com Common causes of this error include the following: - The DNS SRV records required to locate a AD DC for the domain are not registered in DNS. These records are registered with a DNS server automatically when a AD DC is added to a domain. They are updated by the AD DC at set intervals. This computer is configured to use DNS servers with the following IP addresses: 109.188.207.9 109.188.207.10 - One or more of the following zones do not include delegation to its child zone: ad.ourcompany.com ourcompany.com com . (the root zone) For information about correcting this problem, click Help. What am I missing? I'm an experienced Dev, but a newbie Sysdamin experimenting with new stuff. Disclaimer All IP addresses and domains/subdomains were changed to preserve security. If by any chance you still can see private information, please let me know so that I can change it.

  Read the article

• external hard drive is no longer recognized, gives buffer I/O errors

  - by BioGeek

  Hi all, The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive. When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message. [19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21 [19712.145347] usb 2-2: configuration #1 chosen from 1 choice [19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices [19712.147514] usb-storage: device found at 21 [19712.147519] usb-storage: waiting for device to settle before scanning [19717.148978] usb-storage: device scan complete [19717.149527] scsi 25:0:0:0: Direct-Access ST350082 0AS PQ: 0 ANSI: 2 CCS [19717.151020] sd 25:0:0:0: Attached scsi generic sg2 type 0 [19717.151685] sd 25:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [19717.160402] sd 25:0:0:0: [sdb] Write Protect is off [19717.160412] sd 25:0:0:0: [sdb] Mode Sense: 34 00 00 00 [19717.160418] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165685] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165691] sdb: sdb1 [19719.171808] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19719.171818] sd 25:0:0:0: [sdb] Attached SCSI disk [19737.430998] sd 25:0:0:0: [sdb] Unhandled sense code [19737.431007] sd 25:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [19737.431016] sd 25:0:0:0: [sdb] Sense Key : Medium Error [current] [19737.431027] sd 25:0:0:0: [sdb] Add. Sense: Unrecovered read error [19737.431038] end_request: I/O error, dev sdb, sector 6160463 [19737.431050] Buffer I/O error on device sdb1, logical block 6160400 [19737.431060] Buffer I/O error on device sdb1, logical block 6160401 [19737.431067] Buffer I/O error on device sdb1, logical block 6160402 [19737.431075] Buffer I/O error on device sdb1, logical block 6160403 [19737.431082] Buffer I/O error on device sdb1, logical block 6160404 [19737.431088] Buffer I/O error on device sdb1, logical block 6160405 [19737.431096] Buffer I/O error on device sdb1, logical block 6160406 [19737.431102] Buffer I/O error on device sdb1, logical block 6160407 [19737.431114] Buffer I/O error on device sdb1, logical block 6160408 [19737.431121] Buffer I/O error on device sdb1, logical block 6160409 [19737.712183] sd 6:0:0:0: [sdb] Unhandled sense code [19737.712191] sd 6:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [19737.712200] sd 6:0:0:0: [sdb] Sense Key : Hardware Error [current] [19737.712210] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information [19737.712222] end_request: I/O error, dev sdb, sector 0 [19737.712232] Buffer I/O error on device sdb, logical block 0 Neither does the external drive show when I use fdisk: jeroen@phalacrocorax:~$ sudo fdisk -l [sudo] password for jeroen: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000341ad Device Boot Start End Blocks Id System /dev/sda1 * 1 18714 150320173+ 83 Linux /dev/sda2 18715 19457 5968147+ 5 Extended /dev/sda5 18715 19457 5968116 82 Linux swap / Solaris` I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external harddisk. Do I have any other options?

  Read the article

• Linux Mint 14 severe overheating

  - by agvares

  I've tried switching to Mint (it was Mint 12) about 6 months ago, but failed to do it due to enormous overheating which made it virtually impossible to run any applications more complex than Gedit. Time had passed, and now I'm back again with Mint 14, but feeling way more determined. What I face are the following issues: 1) Great overheating (and by great I mean that just by doing nothing my CPU temp is floating around 70-75 C, which I find a lot) 2) Running multiple applications (let's say Chrome, Skype and Pidgin) results in critical overheating and immediate shutdown of the system 3) Due to the stuff listed above, my battery drains in about 10-15 minutes, pretty much turning my laptop into a crippled desktop machine I've got a HP-dv6 laptop (i7, 6gb RAM, dual graphics) Here's the output of lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0d:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01) 19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) what i've tried to do already: 1) I've edited my grub file to add some "splash" arguments there 2) Installed jupiter and powertop 3) Tried to upgrade to newer kernels (up to 3.8), btw running anything newer than 3.5 results in both resolution and wi-fi detection fail 4) Read lots of forum threads devoted to the topic So, my question is simple: What else might I do to become finally able to use Mint as my default OS without the risk of being burned alive by the CPU heat?

  Read the article

• How to grow to be global sysadmin of an organization?

  - by user64729

  Bit of a non-technical question but I have seen questions of the career development type on here before so hopefully it is fine. I work for a fast growing but still small organization (~65 employees). I have been their external sysadmin for a while now, looking after hosted Linux servers and infrastructure. In the past 12 months I have been transforming into the internal sysadmin for our office too. I'm currently studying Cisco CCNA to cover the demands of being an internal sysadmin and looking after the office LAN, routers, switches and VPNs. Now they want me to look after the global sysadmin function of the organization as a whole. The organization has 3 offices in total, 2 in the UK and 1 in the US. I work in one of the UK offices. The other offices are primarily Windows desktops with AD domain shops. My office is primarily a Linux shop with a file-server and NFS/NIS (no AD domain for the Windows desktops yet but it's in the works). Each other office has a sysadmin which in theory I am supposed to supervise but in reality each is independent. I have a very competent junior sysadmin working with me who shares the day-to-day tasks and does some of the longer term projects with my supervision. My boss has asked me how to grow from being the external sysadmin to the global sysadmin. I am to ponder this and then report back to him on how to achieve this. My current thoughts are: Management training or professional development - eg. reading books such as "Influencer" and "7 Habits". Also I feel I should take steps to improving communication skills since a senior person is expected to talk and speak out more often. Learn more about Windows and Active Directory - I'm an LPI-certified guy and have a lot of experience in Linux (Ubuntu or desktop, Debian/Ubuntu as server). Since the other offices are mainly Windows-domains it makes sense to skill-up in that area so I can understand what the other admins are talking about. Talk to previous colleagues who have are are in this role already - to try and get the benefit of their experience. Produce an "IT Roadmap" or similar that maps out where we want the organization to be and when, plotted out over the next couple of years with regards to internal and external infrastructure. I have produced a "Security roadmap" already which does cover some of these things. I guess this can summed up as "thinking more strategically"? I'd appreciate comments from anyone who has been through a similar situation, thanks.

  Read the article

• Issue with Netgear GS108T Managed Switch and Jumbo Frames

  - by Richie086

  I recently purchased a Netgear GS108T managed switch and I am trying to configure jumbo packets between my NAS (Thecus N4100Pro), PC and managed switch. I should mention the fact that I was able to use jumbo frames between my PC and NAS before I purchased the switch without issue. My Desktop has a wired gigabit NIC (Intel 82579V Gigabit) and has the ability to configure jumbo frames (see pic) that are either 9014 bytes or 4088 bytes. I choose 9014 bytes for the jumbo frame size My NAS supports jumbo frames as well, and is configured to use 9014 as the frame size. When I go into my Netgear managed switch and set the frame size to 9014 on the ports I am using for my PC and NAS. See image As soon as I hit apply in the web interface, I loose my connection to the SMB shares on my NAS and I can no longer connect to the web admin interface for my NAS. The really strange thing is I can ping my NAS via the ping command, but when I try to connect to the web interface on port 80 or port 443 the page never loads. I did a scan from my PC to my NAS using nmap and I can see the following ports open PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 631/tcp open ipp 2000/tcp open cisco-sccp 2049/tcp open nfs 3260/tcp open iscsi 49152/tcp open unknown MAC Address: 00:14:FD:15:00:44 (Thecus Technology) Read data files from: C:\Program Files (x86)\Nmap Nmap done: 1 IP address (1 host up) scanned in 211.97 seconds Raw packets sent: 1 (28B) | Rcvd: 1 (28B) Anyone have any idea what is going on here? Why is nmap able to detect the ports are open and listening for http, https and file sharing but I cant connect when all devices have jumbo packets enabled? Stranger still - I did a packet capture using wireshark while the nmap scan was running and filtered so I only saw converstations between my PC and my NAS. Here are the packet details from my scan Only 4 packets over 5k bytes? What is going on here? Do I not need to configure jumbo frame sizes on the switch? I have an internet connection from my pc to the switch to my router - I just cannot connect to my NAS. I just checked on my iPhone and I am able to open my NAS web admin interface without issue on my iPhone! WTF!!!!!! Let me know if you need more details..

  Read the article

• Windows 8.1 IRQL_NOT_LESS_OR_EQUAL with Asus PCE-n53

  - by JArsenault89

  I saw the following question, and it is the exact same problem on my machine, I have tracked it to the ASUS PCE-n53 wireless card in my desktop. Does anyone know of a workaround? Windows 8.1 RTM installation crashes The adapter worked fine in windows 8... any ideas? EDIT: Crash Dump Analysis * Bugcheck Analysis * * IRQL_NOT_LESS_OR_EQUAL (a) An attempt was made to access a pageable (or completely invalid) address at an interrupt request level (IRQL) that is too high. This is usually caused by drivers using improper addresses. If a kernel debugger is available get the stack backtrace. Arguments: Arg1: 0000000000000000, memory referenced Arg2: 0000000000000002, IRQL Arg3: 0000000000000001, bitfield : bit 0 : value 0 = read operation, 1 = write operation bit 3 : value 0 = not an execute operation, 1 = execute operation (only on chips which support this level of status) Arg4: fffff801ef4f1316, address which referenced memory Debugging Details: WRITE_ADDRESS: 0000000000000000 CURRENT_IRQL: 2 FAULTING_IP: nt!KeReleaseSpinLock+16 fffff801`ef4f1316 f048832100 lock and qword ptr [rcx],0 DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT BUGCHECK_STR: AV PROCESS_NAME: System ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre TRAP_FRAME: ffffd00020d45550 -- (.trap 0xffffd00020d45550) NOTE: The trap frame does not contain all registers. Some register values may be zeroed or incorrect. rax=0000000000000001 rbx=0000000000000000 rcx=0000000000000000 rdx=0000000055920200 rsi=0000000000000000 rdi=0000000000000000 rip=fffff801ef4f1316 rsp=ffffd00020d456e0 rbp=ffffd00020d45768 r8=0000000055920222 r9=0000000035930000 r10=0000000055920222 r11=ffffd00020d456a8 r12=0000000000000000 r13=0000000000000000 r14=0000000000000000 r15=0000000000000000 iopl=0 nv up ei pl zr na po nc nt!KeReleaseSpinLock+0x16: fffff801ef4f1316 f048832100 lock and qword ptr [rcx],0 ds:0000000000000000=???????????????? Resetting default scope LOCK_ADDRESS: fffff801ef6da360 -- (!locks fffff801ef6da360) Resource @ nt!PiEngineLock (0xfffff801ef6da360) Exclusively owned Contention Count = 6 Threads: ffffe000010ff040-01<* 1 total locks, 1 locks currently held PNP_TRIAGE: Lock address : 0xfffff801ef6da360 Thread Count : 1 Thread address: 0xffffe000010ff040 Thread wait : 0x1fbe LAST_CONTROL_TRANSFER: from fffff801ef5647e9 to fffff801ef558ca0 STACK_TEXT: ffffd00020d45408 fffff801ef5647e9 : 000000000000000a 0000000000000000 0000000000000002 0000000000000001 : nt!KeBugCheckEx ffffd00020d45410 fffff801ef56303a : 0000000000000001 0000000000000000 ffff0c83e3e25300 ffffd00020d45550 : nt!KiBugCheckDispatch+0x69 ffffd00020d45550 fffff801ef4f1316 : 00000000000a5890 0000000000000001 0000000000000000 ffffe00004c00000 : nt!KiPageFault+0x23a ffffd00020d456e0 fffff80003b430ad : 00000000000afe80 ffffe00004c00000 00000000000a2f80 0000000035720000 : nt!KeReleaseSpinLock+0x16 ffffd00020d45710 fffff80003ac249f : ffffe00004c00000 00000000000000a8 ffffe00004c85050 0000000000000800 : netr28x+0x840ad ffffd00020d457b0 fffff80000b76475 : ffffd00020d459e8 ffffd00020d459f0 ffffe00004ac2006 ffffe00004ac21a0 : netr28x+0x349f ffffd00020d459a0 fffff80000baa248 : ffffe00004ac2eb8 0000000000000000 ffffe00000000000 ffffe00004ac21a0 : ndis!ndisMInvokeInitialize+0x39 ffffd00020d459e0 fffff80000b74784 : 0000000000000050 ffffe00004907ba0 0000000000000000 01cecbbc328e6cde : ndis!ndisMInitializeAdapter+0x4dc ffffd00020d46050 fffff80000b74d3d : 0000000000000050 ffffe0000443e770 ffffc00000951480 ffffe00004ac21a0 : ndis!ndisInitializeAdapter+0x60 ffffd00020d460a0 fffff80000b74c14 : ffffe00004ac21a0 ffffe00004ac2050 ffffe000047ec2a0 0000000000000000 : ndis!ndisPnPStartDevice+0x89 ffffd00020d460f0 fffff80000b87695 : ffffe00004ac21a0 ffffe00004ac21a0 ffffd00020d461b0 ffffe000047ec2a0 : ndis!ndisStartDeviceSynchronous+0x58 ffffd00020d46140 fffff80000b6a760 : ffffe000047ec2a0 ffffe00004ac21a0 0000000000000000 0000000000000000 : ndis!ndisPnPIrpStartDevice+0x13471 ffffd00020d46170 fffff8000032576c : ffffe00004b11501 ffffe00004b11570 0000000000000001 fffff80000325880 : ndis!ndisPnPDispatch+0x140 ffffd00020d461e0 fffff8000030b40a : ffffe000047ec2a0 0000000000000106 ffffd00020d462f0 ffffe00004b116c0 : Wdf01000!FxPkgFdo::PnpSendStartDeviceDownTheStackOverload+0xe8 ffffd00020d46250 fffff80000305942 : 0000000000000106 ffffd00020d462f0 0000000000000105 ffffd00020d464d0 : Wdf01000!FxPkgPnp::PnpEventInitStarting+0xa ffffd00020d46280 fffff80000305a5a : ffffe00004b116c8 0000000000000002 ffffe00004b11570 ffffe00004b11600 : Wdf01000!FxPkgPnp::PnpEnterNewState+0x102 ffffd00020d46310 fffff80000305bc4 : 0000000000000000 ffffd00020d46400 ffffe00004b116a0 0000000000000000 : Wdf01000!FxPkgPnp::PnpProcessEventInner+0xc2 ffffd00020d46390 fffff8000030c27a : 0000000000000000 ffffe00004b11570 0000000000000000 ffffe00004b11570 : Wdf01000!FxPkgPnp::PnpProcessEvent+0xe4 ffffd00020d46430 fffff80000300936 : ffffe00004b11570 ffffd00020d464c0 0000000000000000 ffffe00004a0e630 : Wdf01000!FxPkgPnp::_PnpStartDevice+0x1e ffffd00020d46460 fffff800002fba18 : ffffe000047ec2a0 ffffe000047ec2a0 0000000000000000 ffffe0000486f020 : Wdf01000!FxPkgPnp::Dispatch+0xd2 ffffd00020d464d0 fffff801ef838796 : 0000000000000000 fffff801ef6aa101 0000000000000000 ffffd000208aa180 : Wdf01000!FxDevice::DispatchWithLock+0x7d8 ffffd00020d465b0 fffff801ef4d5bad : ffffe000011dc3a0 ffffd00020d46659 0000000000000000 fffff801ef7f5ba4 : nt!PnpAsynchronousCall+0x102 ffffd00020d465f0 fffff801ef838e57 : ffffe000011db8d0 ffffe000011db8d0 ffffe00004a8d060 ffffc00002b11200 : nt!PnpStartDevice+0xc5 ffffd00020d466c0 fffff801ef838fe7 : ffffe000011db8d0 ffffe000011db8d0 0000000000000000 ffffe000011db8d0 : nt!PnpStartDeviceNode+0x147 ffffd00020d46790 fffff801ef7fd19e : ffffe000011db8d0 0000000000000001 0000000000000001 ffffe00000000001 : nt!PipProcessStartPhase1+0x53 ffffd00020d467d0 fffff801ef897b17 : ffffe000011db8d0 0000000000000001 0000000000000000 fffff801ef7ef7b2 : nt!PipProcessDevNodeTree+0x3ce ffffd00020d46a50 fffff801ef4f5033 : 0000000100000003 0000000000000000 0000000000000000 0000000000000000 : nt!PiRestartDevice+0xaf ffffd00020d46aa0 fffff801ef44565d : fffff801ef4f4c90 ffffd00020d46bd0 0000000000000000 ffffe00004a10170 : nt!PnpDeviceActionWorker+0x3a3 ffffd00020d46b50 fffff801ef4eec80 : 0000000000000000 ffffe000010ff040 ffffe000010ff040 ffffe0000035c900 : nt!ExpWorkerThread+0x2b5 ffffd00020d46c00 fffff801ef55f2c6 : ffffd00020472180 ffffe000010ff040 ffffe00000608040 ffffc00000002710 : nt!PspSystemThreadStartup+0x58 ffffd00020d46c60 0000000000000000 : ffffd00020d47000 ffffd00020d41000 0000000000000000 0000000000000000 : nt!KiStartSystemThread+0x16 STACK_COMMAND: kb FOLLOWUP_IP: netr28x+840ad fffff800`03b430ad 4533e4 xor r12d,r12d SYMBOL_STACK_INDEX: 4 SYMBOL_NAME: netr28x+840ad FOLLOWUP_NAME: MachineOwner MODULE_NAME: netr28x IMAGE_NAME: netr28x.sys DEBUG_FLR_IMAGE_TIMESTAMP: 51de7a8d FAILURE_BUCKET_ID: AV_netr28x+840ad BUCKET_ID: AV_netr28x+840ad ANALYSIS_SOURCE: KM FAILURE_ID_HASH_STRING: km:av_netr28x+840ad FAILURE_ID_HASH: {a1f86ced-f566-ac23-afeb-1aa88ea5ab8f} Followup: MachineOwner

  Read the article

• Stack-based keyboard delay using Logitech MX3100 keyboard

  - by Mark S. Rasmussen

  I've been using a Logitech Cordless Desktop MX3100 keyboard for quite a while. I've never really had any problems, except for the occasional typo. I noticed however that I tended make the typo "Laod" instead of "Load", quite a bit more often than any other typos. As it started to get on my nerves, I decided to do some testing. What I found out was than when I write lowercase "load", I'd never make the typo. All uppercase, or just uppercase L, I'd make the typo quite often. My actual (very scientific) testing is probably best described by showing the output: moatmoatmoat MoatMoatMoat loatloatloat LaotLaotLaot loafloafloaf LaofLaofLaof hoathoathoat HoatHoatHoat hoadhoadhoad HoadHoadHoad lortlortlort LrotLrotLrot What i found out was that whenever shift was depressed, typing an uppercase "L" would induce a significant lag if the next character was an "o", compared to the lag of the any other key: High "o" lag: LoLoLoLoLoLo No "a" lag: LaLaLaLaLaLa No lag for neither "o" nor "a": lolololololo lalalalalala By realizing this I regained a slight bit of sanity as I knew I wasn't coming down with a case of Parkinsons. I was actually typing correctly, the lag just interpreted it wrongly. Now, what really bugs me is that I can't fathom how this is occurring. What I'm actually typing, in physical order, is this: L - o - a - d, and yet, the "a" is output before the "o", even though "o" was pressed before "a". So while the keyboard is processing the "Lo" combo, the "a" gets prioritized and is inserted before the "o" is done processing, resulting in Laod instead of Load. And this only happens when typing "Lo", not when typing lowercase "lo". This problem could stem from the keyboard hardware, the receiver hardware or the keyboard software driver. No matter the fault location however, I can't imagine how this could be implemented as anything but a FIFO queue. A general delay, sure, I could live with that, albeit I'd be irritated. But a lag affecting different keys differently, and even resulting in unpredictable outcome - that just doesn't make any sense. I've solved the problem by just switching to a wired keyboard. I just can't shake it off me though; what kind of bug/error/scenario would result in a case like this? Edit: It's been suggested that I stop drinking Red Bull and stick to water instead. While that may actually help solve the issue, I'm really not looking for a solution as such. I'm more interested in an explanation of how this could happen, as I can't imagine any viable technical solution that could result in this behavior.

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• USB mouse disconnecting and reconnecting randomly and often

  - by Marc

  Specs: Q6600, evga 780I sli mobo, 4gig RAM, logitech MX518, windows 7 64bit, evga gtx 260, 650W power supply (single rail) The problem I am having is my mouse will reconnect/disconnect (will even hear the sounds from windows) and the light on the bottom of the mouse will turn off/turn on as it starts working again. It really sucks to be playing a game (and happens on desktop as well) for the mouse to just die out for a few seconds and come back. Sometimes it will not happen for days and other times it will do it 2 or more times within 15 seconds. I have tried two different wired mice, have tried multiple USB ports (on front of computer, back of computer, have also used a USB hub and have also plugged in a card that connects to the USB connectors on the motherboard and adds a few usb ports to the back of the computer, and I also bought a USB 2.0 PCI card and that did not help). Nothing else seems to reconnect like this, my usb keyboard has never once cut out like the mouse does and neither have any of the other devices I have connected (webcam, usb hub, various devices sometimes connected through usb cables, and IR reciever for windows media center remote). I have disconnected all usb devices except for my keyboard and mouse and the problem still occurs. I guess it could be something wrong with my motherboard but since no other devices behave similarly I'm just hoping that it is some kind of driver conflict. Installing logitech's drivers has had no effect. It seemed at first that if I go to device manager and uninstall HID-compliant mouse (that and logitech mx518 are listed) that would fix it but it doesn't seem to work anymore or at least not every time (it keeps reinstalling). I have googled "usb mouse disconnects and reconnects" and it seems to be fairly common but none of those were resolved. To stick some easy steps: It happens with or without the drivers installed It has happened with multiple mice on the same computer Bios is the latest version (P08) Motherboard drivers are the latest version Device manager is listing no problems on any USB devices Happens with every usb port, even addon usb cards Happens when all usb devices aside from mouse and keyboard are unplugged I read that maybe it is an IRQ conflict and I tried to look into that but did not really know what was going on, but didn't see anything obviously wrong. Thanks for any help guys, its driving me crazy!

  Read the article

< Previous Page | 448 449 450 451 452 453 454 455 456 457 458 459  | Next Page >