Search Results

Search found 23427 results on 938 pages for 'christopher done'.

Page 453/938 | < Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >

• Rebuild mdadm RAID5 array with fewer disks

  - by drjeep

  I have a 4 disk RAID5 array, one of which is starting to fail according to smartd. However, since I'm using less than half the space on /dev/md0, I'd like to rebuild the array without the failing disk. The closest scenario I've been able to find online has been this post, however it contains bits that don't apply to me (LVM volumes) and also doesn't explain how I go about resizing the partition after I'm done. Please note I have backups of important data, but I'd like to avoid rebuilding the array from scratch if possible.

  Read the article

• SAN for Medium Business - Where to start? [closed]

  - by Henson

  I've always run Linux on my home computers, and done PC repair for years, but this is my first experience with needing to buy a SAN. I thought I was knowledgeable, but I feel a bit lost. I need to be able to support 25 VMs, which are currently managed through vSphere. The company I'm at is growing quickly though, so I'd like to plan for the future. Ideally, I want a solution that I can just tack arrays onto and manage as one large, iSCSI drive. Suggestions? Good resources? If I can find something that appears to software as one large drive, am I better off going with a solution like FreeNAS or Starwind, or an all-in-one proprietary solution like NetApp? Cost, is (of course, and always I'm sure) an issue.

  Read the article

• How do I block my ISP from framing websites?

  - by PJB

  I've noticed recently, as of today, that all the websites I visit (except for a specific few sites such as Google) are all put into a frame. I'm not sure what the reason for this is, there are no ads displayed and everything appears normal. The only reason I found out is because the headers weren't loading correctly and none of the page titles showed up properly - I quickly checked the source code and saw that instead of the source of the page I was expecting to see, there was a single line with a frame. I first thought maybe somekind of trojan, but after going through various checks I've determined it's my ISP and/or somekind of Internet Registry (I traced the IP shown in the source code) What can be done to prevent this frame, short of using a VPN? I feel like I am being spied on. PS: I'm located in South Korea.

  Read the article

• Turn 2 USB type A ports (receptacles) into an extension cable with 2 type A receptacles using Linux?

  - by Tianyang Li

  I'm currently trying to connect 2 USB devices together, but both ends are type A plugs. Before I buy a physical extension cords with 2 type A receptacles, I'd like to know if I can connect these 2 devices together at all by passing data "transparently" through a Linux box with = 2 USB ports. I'm actually trying to connect a keyboard to an Android phone, and I want to first try if it can work by using a Linux box as a "virtual" USB extension cord. Has anybody done something like this before? Thanks!

  Read the article

• C# calendar needs Business Logic for real-time reminders? [on hold]

  - by lazfish

  I am not a super experienced C# user, though I have some experience in .Net and VB.Net. Just got this new job and my first assignment is a mission critical part of the business. It is pretty important I get it right so I was hoping for some sage advice. We have created a calendar using jQuery, C#, .Net & SQL Server 08. The calendar works but now we are wanting to add email, SMS and voice-call reminders. We are a small company and can do whatever we need to do with no restrictions on our IT environment. I have some base-line experience with Unix servers but would prefer to stay in the Micro$oft universe if it is prudent to do so. I know how to add the API calls and services to initiate these reminders (using built in email services for email and Twilio.com for SMS). I am asking for advice about how to approach a reliable and timely listener service that knows when to call the service or API for the reminder before an appointment. EG. SMS: "You have a conference call in 30 minutes." I have done some research, but it is hard to know what is a proven reliable approach. What I am looking for is an experienced opinion on a good (or the best) strategy for implementing a solution that will reliably listen for appointments and dispatch the reminders when needed.

  Read the article

• When to open source a project under development? [closed]

  - by QuasarDonkey

  Possible Duplicate: Is it OK to push my code to GitHub while it is still in early development? I've been working on a hobby project for a few months now; it's clocking in at over 15000 source lines of code. A number of people have expressed interest in joining development, and I have full intentions of going open source, since it would not be feasible for me to complete the project alone. I'm just not sure when to open-source it. For context, I've notice many successful open source projects, such as the Linux kernel, had considerable work done before they were open-sourced. In my case, I'd been planning on open-sourcing it after I complete all the underlying libraries and overall architecture. Is this a mistake; should I just release it right now? I'm worried that since certain critical underlying components haven't been finalized, if people build a large codebase around them, it will be very difficult to change or fix things later. On the other hand, it's a very large project that will require multiple developers to complete in a reasonable time. So when is the right time during development to go open source? Preferably, I'd like to hear from some folks who have started their own projects.

  Read the article

• Delete Ubuntu and Grub from PC (and BIOS unaccessible)

  - by Temitope

  I've really done a mess while upgrading 12.04 to 12.10, or my PC did, or ubuntu did, I can't really tell. The situation now is I have a dual booting machine, Windows 7 and ubuntu 12.10 -When turning on the PC, I can't access boot options, I've tried every thing, esc, f1 f8, f10 (I have a Hp pavilion) but all I can see is a short-lasting screen with three lines reading something like "error:files not found" or "link not found". So the PC turns to the Grub loader screen. This is already a BIG problem. It means I can't change boot order, and I'm diperate, since it doensn't seem that repairing my operating systems will bring my BIOS back. -If I chose Ubuntu in grup, it loades but then frezes on the desktop, I may be having problem with unity3d, or compiz, which was reported to be crashing the first times I started ubuntu. Now, after turning off and on the pc several times, no crash is reported again. Ubuntu just load my background image and nothing else. Not the side menu, not the header, nothing. Althogh the system seems "functioning", when I press the power button on the PC, for example, the normal shutdown dialog window appears. -If I chose Windows, Grubs tells me that something is not found, and to press any key to continue; I do it and then Windows loads perfectly. What I now want to do is 1- use EasyBSD to change boot order and boot Windows partition first 2- delete the ubuntu partitions from within windows disk manager What I except happening is that My PC turns to, or near to factory booting settings: I press the power button and Windows loads without asking me nothing I have acess to all my hardisk from withing windows Is that what will really happen? Are there danger I'm not seeing? What I don't except happening is The BIOS access key return functioning How could I eventually solve this? I would like to reinstall Ubuntu, 32 bit version this time.

  Read the article

• Google Code C++ [closed]

  - by JacKeown

  I was on this website: http://code.google.com/edu/languages/cpp/basics/getting-started.html#learn-by-example and I saw this code: // Description: Illustrate the use of cin to get input // and how to recover from errors. #include <iostream> using namespace std; int main() { int input_var = 0; // Enter the do while loop and stay there until either // a non-numeric is entered, or -1 is entered. Note that // cin will accept any integer, 4, 40, 400, etc. do { cout << "Enter a number (-1 = quit): "; // The following line accepts input from the keyboard into // variable input_var. // cin returns false if an input operation fails, that is, if // something other than an int (the type of input_var) is entered. if (!(cin >> input_var)) { cout << "Please enter numbers only." << endl; cin.clear(); cin.ignore(10000,'\n'); } if (input_var != -1) { cout << "You entered " << input_var << endl; } } while (input_var != -1); cout << "All done." << endl; return 0; } I was wondering... what is the significance of cin.clear() and cin.ignore() ...and also why the 10000 and /n parameters are necessary...?...

  Read the article

• Why does Ubuntu 12.10 Beta2 insist on commiting changes to the partition table?

  - by Uten

  Why does Ubuntu 12.10 Beta2 insist on commiting changes to the partition table even as no real changes has been done? This is a show stopper for me as I'm installing without a CD/DVD ROM. This is how I go about it. I downloaded the iso image and extracted vmlinuz and initrd.lz to the same folder I keep the iso image. Configured grub (0.9x) to boot /ubuntu/vmlinuz with the iso image like this: title ubuntu live-cd kernel /ubuntu/vmlinuz boot=casper iso-scan/filename=/ubuntu/ubuntu-12.10-beta2-desktop-i386.iso ro quiet splash initrd /ubuntu/initrd.lz boot This works well and I get a running livecd session. The iso image is mounted on /isomedia (or something similar). The spare HD space where I want to install Ubuntu is in the logical area (at the wery end of the disk). I have tried both to use the space as empty and preformated with ext4. After selecting the partition and selecting "use as ext4" and selecting a mountpoint (/) I get the message: "The installer needs to commit changes to partition tables, but cannot do so because partitions on the following mount points could not be unmounted" "/isomedia" (or something similar). Is this a "feature" of the installer? To insist that everything is unmounted even if no changes is nescesary (as fare as I understand). It's probably a safety feature but is it needed? I have cahnged layouts with parted and gparted (at the end of the disk) for years without any failures. I understand that booting the iso image like this is not the common way. But it is just such a beautifull way of doing it when you hav a running system and want to play with another. Any one had any success installing Ubuntu (12.10 beta2 ) like this? Best regards Uten

  Read the article

• Why might one hard disk perform slower than another?

  - by Styne666

  I have just bought two WD 3TB Reds (WD30EFRX) for a FreeNAS box and whilst doing burn-in testing it seems like one is consistently taking about 10% longer than the other. So far I've done: a dd read test of the whole device, a long SMART test and it's currently halfway through a badblocks -wvs. The second device is lagging behind the first on all of them. I'm running these commands on Debian stable in two Konsole tabs. Is there a reason this could be considered normal behaviour or is it worth running the tests independantly? They're both plugged in to the LSI 2308 (IT mode) on a Supermicro X10SL7-F.

  Read the article

• db2 tablespace size and performance impact

  - by jrhickey

  Originally when we began moving to db2 LUW we ran into some issues where our tables were too big to fit into the default 4K table space. As a result of "pressure" to get it done we just went with a 32K default table space and put ALL of our tables there. What impact would that have if any? I talked to one person who said that it would possible make out database MUCH larger than it needed to be. Is that true? What about memory? Would there be any benefit to moving the smaller tables back to a 4K table space? I have looked around in forums and what not but cannot seem to find a good answer.

  Read the article

• machine ignoring host file?

  - by squinny

  so i can ping the ip adress for the server i need but when i ping it by name, the server name is followed by an incorrect ip address. My host file is updated, i can communicate with my machine from my server just fine. i can access websites on the server by typing the ip adress into the adress bar followed by the name. it is like my machine is ignoring my hosts file... i have updated re updated...flushed dns, u name it ive done it any ideas?

  Read the article

• Put subdomain in another server (reseller hosting), what domain i put in order form?

  - by basketmen

  I want to put some subdomain.mydomain.com in another server i understand in current server, in WHM Edit DNS Zone mydomain.com i just need to add A record like subdomain A 222.222.222.222(another server IP) before that, i need to set the another server first, so i want to order a reseller hosting for the another server. My question is what domain i need to put in the order form? Is it ok still put mydomain.com? Because i tried put subdomain.mydomain.com but its says not valid domain. Its standart hosting order form, using WHMCS and what nameserver i need to use in the another server WHM later Basic cPanel & WHM Setup Nameservers, is it still ns1.mydomain.com and ns2.mydomain.com like current server use? Where i need to create the nameserver for the another server? please help, this should be easy if you have done it before

  Read the article

• Slow Crash with Filter Manager

  - by Alex N.

  I have been having sporadic freezes on my machine lately. There is no blue screen or crash screen. All the applications just stop responding and ~5~10 minutes later it will power off. After checking the event log a couple times, I have found that the same event occurs right before each crash. File System Filter 'Avgmfx64' (6.1, ?2011?-?12?-?23T08:08:12.000000000Z) has successfully loaded and registered with Filter Manager. My question is twofold: I can not seem to find any information on what the Filter Manager actually is supposed to do. for curiosities sake, what is it? And more importantly, how do I fix this problem. From the research I have done, I see that similar problems can be caused by out of date drivers, so I have already taken the time to update all of my drivers, run MemTest, and verify the drive integrity.

  Read the article

• Why can I browse to localhost, not to my computer name? (IIS7) [closed]

  - by Lost Hobbit

  I'm not very clued up on IIS, but I'm trying to do something that I thought would be quite simple. In IE, if I browse to http://localhost:80, I am greeted with a pretty picture with a bunch of welcome messages and a big "IIS7", thanks to the graphic designers at Microsoft. In IE, if I browse to http://mycomputername:80, I'm greeted with 404. It may be my fault... perhaps I've done something weird. Chrome replies 404 to either of those. Should this work, and if so, what am I doing wrong, or what can I do to get it to work? What might cause this to happen and how can I fix it? EDIT To add a bit more information. I did find after posting this question that http://localhost:80 was the only URL I could access on my local PC. I could not access any of the virtual sub-directories on localhost via my browser.

  Read the article

• Ubuntu: Resize the root LVM(2?) partition

  - by user12259

  I have an Ubuntu virtual machine running in VirtualBox 2.2.4, and I created it on an 8gb virtual disk which is too small. So, I am trying to increase the size of the disk. So far, I have done this: Created a new larger virtual disk Added the 2nd disk to the machine Used CloneZilla to clone the first disk onto the 2nd disk Removed the first disk Booted up off the 2nd (larger disk) But now I'm still stuck with an 8gb partition on my new 100gb virtual disk. Whats the easiest path from here to having a 100gb partition? :) I gather GPart can resize partitions, but it doesn't seem to support LVM2 partitions, which mine seems to be. thx Alex

  Read the article

• Software update shows "P??roblem with the system installer tool" error in OS X Lion

  - by Elnaz Shahmehr

  I can't update my system. Does anyone know what the problem is? sudo softwareupdate -i -a Password: Software Update Tool Copyright 2002-2010 Apple Downloading Digital Camera Raw Compatibility Update Waiting to install Digital Camera Raw Compatibility Update Downloading Java for OS X 2012-002 Verifying Java for OS X 2012-002 Waiting to install Java for OS X 2012-002 Downloading iTunes Waiting to install iTunes Downloading Safari Verifying Safari Waiting to install Safari Checking packages… Installing Waiting for other installations to complete… Validating packages… Writing files… Package failed: There was a problem with the system installer tool. Package failed: There was a problem with the system installer tool. Package failed: There was a problem with the system installer tool. Package failed: There was a problem with the system installer tool. Done.

  Read the article

• How to make googlebot to crawl a page? [closed]

  - by mamadum

  What is the best way of forcing googlebot to crawl the page? I've put up Google analytics, registered site with Google webmaster. I've done great deal of SEO work on the website with keywords and titles, I took care of microdata. I submitted the site anonymously, I successfully fetched the site and submit for indexing couple of days ago and still nothing. Last time googlebot visited the site is almost 1 month ago and the indexed content is now obsolete. Am I missing something? or is it just a slow process??

  Read the article

• Play sound on menu items on hover [migrated]

  - by Mahalia Samuels

  How can I go about making a sound clip play when an element is hovered over? I'm using the latest Wordpress, and the parent theme I am using gives me an option to paste scripts which it will embed to the <head> section. Is there a script which I can just add to my <head> that will play the sound when the cursor moves over my menu item class .menu li? I spent several hours trying to figure this out the other day with no avail. I've done this before in a simple HTML website: <head> <script language="javascript" type="text/javascript"> function playSound(soundfile) { document.getElementById("dummy").innerHTML= "<embed src=\""+soundfile+"\" hidden=\"true\" autostart=\"true\" loop=\"false\" />"; } </script> </head> <li><a href="index.html" onmouseover="playSound('lib/hover.mp3');" onclick="playSound('lib/click.mp3');"><span>Home</span></a></li> Not sure how to deploy this on Wordpress though.

  Read the article

• Rewrite (or add) "Sender: " header when MAIL FROM is not the authenticated user

  - by nbevans

  I need to get Postfix to inspect the MAIL FROM of the envelope and determine whether it matches the authenticated user of the session. If it does not, it should then add or update the "Sender: " header inside the e-mail so that its value is that of the authenticated user. I understand that this can be done using sender_canonical_maps but, having tried a few remedial tests, I'm unable to get it working. More than anything I would like to know whether this is actually possible with Postfix, and secondly whether I am in the right ball park. Lastly, an example of how to do it would be fantastic. Thanks very much.

  Read the article

• How to know if a server is physical or virtual? [duplicate]

  - by tachomi

  This question already has an answer here: is there anyway to know if your supposedly fully dedicated server is really a virtually resource-shared machine? [duplicate] 5 answers How can I know if my provider is giving me a dedicated physical server or if I'm getting virtual servers? The provider is from an other country so I don't have the chance to go and see the servers by myself, all of them have linux and they're managed by SSH. All the hire has been done by internet or phone. Are there any commands, dirs to analyze or a way to get this info? They of course tell me that the servers are physical, but when they make some support or hardware/software upgrade or that kind of stuff doesn't take a long. For example, when I ask for a new one with specific requirements at the end they give me more infrastructure than the one I asked for. Of course no one gives extra things without an extra price. Hope I have hinted

  Read the article

• Unable to use strong encryption

  - by user224299

  So I am exploring Apache to create a simple example: the default page and a directory "secure". I everyone to be able to access the server but, when one wants to access the "secure" directory, I the connection to use strong encryption. I am using apache2.4. However this is not working and I don't know why! I have done just like in the Apache tutorial: LoadModule ssl_module /usr/lib/apache2/modules/mod_ssl.so <VirtualHost *:443> SSLEngine on SSLCertificateFile /home/vitorpereira/Desktop/cert.cer SSLCertificateKeyFile /home/vitorpereira/Desktop/key.key </VirtualHost> SSLCipherSuite ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL <Location /var/www/html/secure> SSLCipherSuite HIGH:!aNULL:!MD5 </Location> But this does not work :/ And, I can access the secure folder with http but when I write https, it says not found!

  Read the article

• Server not repsonding after Ubuntu upgrade

  - by aaa

  I have a server that was running Ubuntu 8.04. I upgraded Ubuntu via the command-line and got no warning messages. After it was done the server restarted but now I am unable to SSH back in. My site is also not resolving. My guess is I overwrote something important. What are some trouble-shooting steps I can take? I am able to execute commands through my VPS provider's admin interface. I'm not sure what version it upgraded me to honestly.

  Read the article

• What language and tools can I use to create a simple game with child-lock (capture all key press) for Windows? [closed]

  - by scw

  I'm writing an open source program that changes colors & plays sounds when keys are pressed. I want it to run in full screen mode and have a child-lock so kids can't exit accidentally. I want it to capture all keys including ctrl alt delete. (So it's partially a game, but partially windows utility.) My target OS is Windows 7 (32 & 64 bit), keeping Windows 8 in mind. My options: Visual Studio using .net C# Windows Forms - the devil I know. But not a "game" platform, which is why I'm asking this question. Visual Studio & XNA - have never used XNA, not sure of capabilities or support future Python - What flavor, what modules, what IDE? I've never done anything with Python but I found a couple of similar open source projects in python. Something else that I don't know about? Any input is appreciated.

  Read the article

• Automatically kill processes that over time uses 95%+ of resources? Ubuntu

  - by data_jepp

  I don't know about you're computer but when mine is working properly no process is sucking 95%+ over time. I would like to have some failsafe that kills any processes behaving like that. This comes to mind because when I woke up this morning my laptop had been crunching all night long on a stray chromium child process. This can probably be done as a cron job, but before I make it a full time job creating something like this I'd thought I should check here. :) I hate reinventing the wheel.

  Read the article

< Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >