Search Results

Search found 21861 results on 875 pages for 'external library'.

Page 453/875 | < Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >

• How can I connect to a CIFS/SMB share on a non-default port?

  - by fsckin

  I'm trying to get a contractor connected to a CIFS share (port 445). He's not a big shop (so no go on using VPN). His ISP blocks outgoing connections on port 445. I've been doing some rsync to ftp madness as a workaround to have the share available to him, but it's getting out of control -- we're syncing nearly 40GB a day to an external ftp site and it's going to be much easier just to have him connect and only grab the stuff he needs. So... I can have the CIFS share open to the internet (filtered to allow access to his IP only) on port 446. How the heck can he connect to that? I looked through "net use" and didn't see anything about using another port.

  Read the article

• Getting a black laptop screen

  - by Vivek

  I get a black screen when I boot my laptop. The laptop was in sleep mode initially, so when I pressed the power button, it looked as if it woke up from sleep mode, but the screen was blank. So, I held down the power button to force shutdown the laptop and then removed the battery. But after booting the laptop the screen still remains black. The bios/boot screen remains black as well. I have tried connecting it to external hdmi/vga/s-video devices and booting still no go. Windows loads fine, as I can type the password and get the 'Ding', then alt-f4 and shutdown windows. If it helps, the laptop model is Asus G1S-A1. Thanks in advance!

  Read the article

• Route traffic on vpn to another interface on an ASA 5510

  - by Dave

  I have a ASA 5510 that has about 60-70 vpn tunnels. I have four interfaces on the device: 1)External, 2)192.168.1.0, 3)192.168.2.0, 4) 192.168.3.0 A VPN tunnel is configured from the remote site (192.168.200.0) to the 192.168.2.0 subnet on the ASA. I have remote applications I would like the users at the remote site to be able to access which are hosted on the 192.168.3.0 subnet. I can route traffic between the subnets that are located on the ASA. Any way I can route traffic from the remote site to the 192.168.3.0?

  Read the article

• How can I migrate websites between two identical servers?

  - by edude05

  I have two servers that have a nearly identical (software) configuration. We are upgrading the web servers to run windows server 2008 R2, one already is however the main one (that currently has sites) is on WS2008. Now, the old server is ns.mydomain.com and the new server is ns1.mydomain.com. Since dns automatically fails over to ns1.mydomain.com I'd like a way to move all the vhosts to the new server. Is there an automatic way to move / recreate all the vhosts on the new server? I have figured out how to migrate the DNS records already DNS Migration and since both servers are on the same private network migrating the website data isn't a large issue. Every site is running PHP & MySQL and the MySQL server is external so the records won't have to be moved. Thanks

  Read the article

• non-interactively upload file to sftp server, using password

  - by matt

  Hello Guys, I know, this is not the recommended way to do this. But, I do not have another choice: I've got to set up a cron job that will regularly upload a file to an external SFTP Server (no FTP available, and I do only have a username/password for it but no key.) Still, I need to set up a cron that will regularly connect to that sftp and upload a file. sftp <<EOF put filename exit EOF therefore will not work, because sftp asks for the password, before STDIN is evaluated. What can I do, to pass the Password to sftp? Again: I am aware of the potential security risk, but I really do not have any choice here, and the server from which the file is uploaded is protected rather well.

  Read the article

• HALEVT troubleshooting: VFAT usb storage device gets mounted with root:root user:group

  - by Nova deViator

  Hi, i'm banging my head for number of days around this problem. using Halevt for automounting, everything mostly works, but the only thing is that Halevt mounts external USB storage devices as root. So, as user i cannot write to files on them. Halevt gets run as halevt user on boot through /etc/init.d script. This is Ubuntu Lucid with Awesome WM. No GDM. Running halevt as user seem to not work (halevt runs but doesn't respond on Insert) I know HAL is deprecated and removed and i should probably write my own UDEV rules, but until then it seems there must a be simple hack that enables mounting VFAT/NTFS devices with specific uid/gid. this question/answer helps a lot, but not specifically to the above.

  Read the article

• How do I get Chrome to not try to open in Windows 8 mode?

  - by Citrus Rain

  It's not that I'm trying to make it more like 7. That's not the problem. My problem is that whenever I click the Google Chrome icon on my taskbar or even the desktop, Windows brings up this screen-spanning message box saying that my resolution is too low to launch run Google Chrome, and to set my computer to a higher resolution. (I can't.) It then continues to open Chrome correctly after I hit close. This also happens when I click a link in an external program like skype or psi.

  Read the article

• Can I grant permissions on files in windows 7 using a security identifier from another machine

  - by Thomas

  I have an external hard drive, and I wish to grant permissions on some files to users from 2 different computers without having to hook it up to the 2 different computers. I know the SID of the user on the other computer, I'd like to know if and how I can grant permissions to files using the SID. I'm running Windows 7 Professional 64 bits, and "The Other" computer Win 7 Home Premium 64 bits, they are not in a domain, but separate computers on a home network (not even same homegroup). Note: Duplicated question with: Is there a way to give NTFS file permissions to users from other Windows installations?

  Read the article

• What is the Best Free Linux Gateway

  - by rockinthesixstring

  I'm looking at moving away from using my DIR-825 as a gateway and moving into a Linux box to do it all for me. I've found IPCop, but I'm looking for something with a little more power. My main goal is basically to be able to point different external domain names to different internal servers. backup.example.com - 192.168.0.5 home.example.com - 192.168.0.1 I host my DNS on my own dedicated server (windows), so I don't know much about doing the gateway thing in my home (my hosting provider does it all for me). Do any of you know of any free Linux Distros that can accomplish what I'm looking for?

  Read the article

• Dummy HTTP server for debugging

  - by Andrea

  This is more or less the inverse of my previous question. I need to debug some HTTP requests that I am making. Since these requests arise from the use of some external libraries, sometimes I am not sure of what is the actual data I am sending. Is there some dummy server (for Linux) that accepts HTTP requests and just prints them somewhere so that I can inspect them? I would like to be able to see in plain text the full request, like POST /foo HTTP/1.1 Host: www.example.com Accept: text/xml,text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5 Accept-Language: en-gb,en;q=0.5 Content-Type: text/plain Content-Length: 11 Hello world

  Read the article

• Moving the OS X swap file to a faster drive

  - by Milky Joe

  I have a new Mac Mini that's running the latest version of Snow Leopard. The internal drive is a bit of a slouch. I'd like to move the swap file (or whatever it's called is OS X) to my faster external drive (Firewire 800, permanently connected). Is this possible? I've read that the old solutions aren't working in 10.6. My Mac has 2GB of RAM, so the swap file is used quite a bit when I'm doing intensive work (Photoshop etc).

  Read the article

• Option and command keys in OSX are swapped and keyboard preferences do not set them back.

  - by bikesandcode

  On my MacBook pro, I occasionally use external keyboards, generally Windows ones and things have been fine. Yesterday, I plugged in a new one, remapped the command/option keys so the windows/alt keys were in the same configuration, again, nothing new here. However, this time when I unplugged the USB keyboard, the laptops option/command keys remained switched. More annoying is that if I go into the System Preferences - Keyboards - Modifier keys, remapping the keys to actions does not work. I can use the drop downs to disable any specific keys, but switching the behaviours does nothing. (Cmd/Option obvious, tried remapping anything to caps lock and a few other combinations, no joy. Restore defaults set the configuration to what I'd expect, but the settings are evidently ignored.) So: Any ideas?

  Read the article

• Screen flicker -> Severe System Slowdown?

  - by Adam Robinson

  I'm using a Dell D830 laptop, and over the last few weeks it's been developing a very irritating screen flicker problem that leads to the system slowing down almost to the point of unusability. At seemingly random times (no commonality between how long the system has been running, what I was doing, what applications were open, etc.) my screen (I use two external LCD's with the laptop closed in a dock) flickers for a moment, then the system becomes incredibly slow. The screen redraws painfully slowly--almost like what you might expect to see with generic graphics drivers installed--and the entire system is maddeningly unresponsive. The only thing that seems to be able to correct the issue is a restart. I've checked the event logs and nothing out of the ordinary is there, and definitely nothing that's common to all of the events. I'm running XP Pro SP2. Any ideas?

  Read the article

• Configure postfix to filter email into hold queue

  - by Ian

  Hey, I would like postfix to send all emails received on SMTP off to an external process, which will decide whether to allow them through as normal, or whether to put them into the hold queue (or another quarantine area), where they have to wait for admin approval. I was thinking of doing this with an after-queue content filter, which uses pipe(8) to run a script on each message, and the script itself will spawn "postsuper -h " if it decides to put the message on hold. Then the admin can do postsuper -d or -r to delete or pass the message on as appropriate. So, my questions are - a) will this work, and b) is this the best way to do it? Would a milter or another type of content filter be a better approach?

  Read the article

• HP proliant dl360 g5 fails to reboot

  - by user1039384

  Some history of this also available here. As of my latest update on the forum linked above, now cold reboot as well as hard reset and following boot for my proliant dl360 g5 works as expected and successfully boot the system. However, soft-reboot results in internal health indicator turning RED on the front and long beeps every around 6seconds until I either cold reboot or press and hold the power button. A summary of system state when this happens: Internal Health led indicator: RED External Health led indicator: Green No led next to any component is red or amber No POST message neither on the video output nor on IML logs (verified both at the time issue occures and after cold reboot that boots the system successfully). Any thoughts please share. I hope we can knock this issue down together with your help!

  Read the article

• Spanned volumes on new install

  - by Noio

  My Windows 7 Release Candidate is about to expire, so I'm going to do a clean install of a retail version. I have two volumes, on four physical drives, as follows: Disk 0: Spanned Volume (D:) Disk 1: Primary Partition, Boot/Windows Install (C:) Disk 2: Spanned Volume (D:) Disk 3: Spanned Volume (D:) If I install Windows to a formatted drive 1, will it still recognize the spanned volume in Disks 0, 2, and 3? The spanned volume is not redundant in any way, so the volume is 1.5TB consisting of three 500GB disks. I don't have the space to do an external backup, and I thought it was impossible to convert a spanned volume back to a basic volume.

  Read the article

• Does an SMTP request contain host header information (or just the IP of the targeted SMTP server)?

  - by Olaf

  We are using an external commercial smtp server for our newsletters (sending them through .NET components), and they offer two smtp URLs - smtp.critsend.com and fast.critsend.com -, and the second one is reserved for sending singular emails, the first one for bulk. Using nslookup shows that both resolve to the same 4 IP addresses (fast.critsend.com being an Alias). Question: (how) is it possible for the smtp relay to distinguish between different names? Is there something in the headers that can be compared to host headers in http protocol (I didn't find any intelligible information for a non-sysadmins)? The reason I'm asking is because we would like to use one of the IPs in our newsletter script (which works) rather than a name (in order to save DNS requests), and we are wondering about potential problems.

  Read the article

• How to make ssh/rsync/etc use a VLAN network interface?

  - by Annan

  A company I work for has a number of virtual servers with ElasticHosts. They are setup in such a way that eth1 is on a private VLAN connecting them to each other. This is so backups sent between servers are not charged at the same rate as external data transfer. My understanding of how VLANs and network interfaces work is sketchy at best. How can I make ssh, rsync, etc. transfer data through the VLAN? My final solution: I spent a while trying to figure this out, For all servers involved, edit /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static ONBOOT=yes HWADDR=YOUR_MAC_ADDR IPADDR=192.168.0.100 NETMASK=255.255.255.0 Where HWADDR should already be set and the last octate of IPADDR should be different from each other. Then run, on all servers /etc/init.d/network restart After this the IP addresses specified by IPADDR can be used directly as any other IP address.

  Read the article

• Sendmail relay out of Amazon EC2?

  - by Stephen Belanger

  I have a site running on CentOS 5.4 through Amazon EC2. Unfortunately, Amazon has had nothing but trouble with their entire IP range getting black listed from spam tracking services regularly. I need a mail server, so I setup an smtp server elsewhere that I want to send to, but I can't just send directly to it through PHP because the direct smtp request is way too slow. What I want to do is relay through sendmail, but I've never used sendmail before, so I have no idea how to configure it. All I want is for all emails sent from localhost to be relayed to one specific external server, but I don't know how to do that. I tried to find a tutorial online, but couldn't find anything that was particularly clear as to how I go about doing that. Can anyone help me out?

  Read the article

• Dell Latitude E4300 TouchPad - Odd Behavior

  - by Cade Roux

  I'm seeing some intermittent behavior on the touchpad. First it wasn't working at all. Then during restart, for a little while it seemed like the buttons attached to the joystick and external mouse were both swapped left/right. Then I went in to the dell touchpad control and disabled the touchpad and re-enabled it and nothing happened. Then a short while after disabling the joystick the touch pad started working. So I restarted to see if it would keep the settings and before login, the touchpad appeared to work, then after login it stopped working for a few minutes while login continued. Then after the login was almost completed it started to work again. It appeared to have retained the settings for the disabled joystick. It seems like perhaps there are conflicting mouse drivers trying to simultaneously or similar. This doesn't seem normal for the touchpad to be disabled for so long after login. What steps should I take to ensure the drivers are right?

  Read the article

• What is IPKVM and why would I need that to install SQL Server on my Web Server?

  - by Eric

  Hello. I have a dedicated server, and will be installing SQL Server. However, my hosting company said they can connect an external CD ROM drive and give me KVM over IP to install SQL Server. My question is, what is IPKVM, and how does it work? Do I need special hardware or software on my side to use it....or do I just connect via remote desktop? Also, why can't I remote into my server through remote desktop instead of using KVM over IP?

  Read the article

• losetup does not decrypt device in Ubuntu 11.4 as before

  - by Kay

  I had an external volume mounted using losetup for about two years. It was created using Ubuntu 9.4 and I used the same Ubuntu installation throughout all dist upgrades. Now as I bought a new laptop I set up a fresh Ubuntu 11.4 installation on it. Problem is: losetup -e twofish /dev/loop0 /dev/sdb2 does not decrypt the volume anymore. The data in /dev/loop0 contains apparently random data. I am sure I entered the correct password. I modprobe'd cryptoloop and twofish. My question is: Has Canonical done some obscure changes to losetup like adding a salt? Does losetup depend on configuration files I did not know about? How can I decrypt the volume on my now laptop?

  Read the article

• How to go about scheduling a task in windows 7 to change wireless connection

  - by Skindeep2366

  This may or not be something that can be done. I cannot find anything on the wireless connection manager built into windows 7 let alone methods for passing params into it. Problem is as follows: I have 2 wireless routers. One provides internet access, the other provides sole access to the local network. Every day at 4am the main system creates a backup in 2 locations. One is a External usb drive, the other is a location on the network. This is all cool if it is remembered to change over to the local network router before leaving. But if it is forgotten the roof will collapse, the walls will burn, and I will be... well you get the idea. Solution: there is already a custom event that fires a automated backup program at 4am everyday. I need someway to force the wireless network to use the correct connection at say 3:58am everyday. Any ideas????

  Read the article

• Dell 620 display is too bright to use

  - by keith

  I have a Dell D620 with a display problem. In windows 7 the display seems to be too bright, the text is broken up, the only way to see the mouse is at a very oblique angle. Changing the brightness with fn and brightness control has little/no effect. When I put it in high contrast mode I can see all the colors, but any windows pictures etc are still useless. I cannot get it to connect to an external monitor via VGA port or via a USB-VGA connector.

  Read the article

• Iptables based router inside KVM virtual machine

  - by Anton

  I have KVM virtual machine (CentOS 6.2 x64), it has 2 NIC: eth0 - real external IP 1.2.3.4 (simplified example instead of real one) eth1 - local internal IP 172.16.0.1 Now I'm trying to make port mapping 1.2.3.4:80 = 172.16.0.2:80 Current iptables rules: # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE -A PREROUTING -p tcp -m tcp -d 1.2.3.4 --dport 80 -j DNAT --to-destination 172.16.0.2:80 COMMIT # Completed on Fri Jun 29 17:53:36 2012 # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *mangle :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed on Fri Jun 29 17:53:36 2012 # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT # Completed on Fri Jun 29 17:53:36 2012 But there is nothing works, I mean it does not forwards that port. Similar configuration without virtualization seems to be working. What am I missing? Thanks!

  Read the article

< Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >