Search Results

Search found 11924 results on 477 pages for 'openoffice org'.

Page 453/477 | < Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >

• "power limit notification" clobbering on 12G Dell servers with RHEL6

  - by Andrew B

  Server: Poweredge r620 OS: RHEL 6.4 Kernel: 2.6.32-358.18.1.el6.x86_64 I'm experiencing application alarms in my production environment. Critical CPU hungry processes are being starved of resources and causing a processing backlog. The problem is happening on all the 12th Generation Dell servers (r620s) in a recently deployed cluster. As near as I can tell, instances of this happening are matching up to peak CPU utilization, accompanied by massive amounts of "power limit notification" spam in dmesg. An excerpt of one of these events: Nov 7 10:15:15 someserver [.crit] CPU12: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU0: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU6: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU14: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU18: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU2: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU4: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU16: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU0: Package power limit notification (total events = 11) Nov 7 10:15:15 someserver [.crit] CPU6: Package power limit notification (total events = 13) Nov 7 10:15:15 someserver [.crit] CPU14: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU18: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU20: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU8: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU2: Package power limit notification (total events = 12) Nov 7 10:15:15 someserver [.crit] CPU10: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU22: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU4: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU16: Package power limit notification (total events = 13) Nov 7 10:15:15 someserver [.crit] CPU20: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU8: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU10: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU22: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU15: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU3: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU1: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU5: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU17: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU13: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU15: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU3: Package power limit notification (total events = 374) Nov 7 10:15:15 someserver [.crit] CPU1: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU5: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU7: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU19: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU17: Package power limit notification (total events = 377) Nov 7 10:15:15 someserver [.crit] CPU9: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU21: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU23: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU11: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU13: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU7: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU19: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU9: Package power limit notification (total events = 374) Nov 7 10:15:15 someserver [.crit] CPU21: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU23: Package power limit notification (total events = 374) A little Google Fu reveals that this is typically associated with the CPU running hot, or voltage regulation kicking in. I don't think that's what is happening though. Temperature sensors for all servers in the cluster are running fine, Power Cap Policy is disabled in the iDRAC, and my System Profile is set to "Performance" on all of these servers: # omreport chassis biossetup | grep -A10 'System Profile' System Profile Settings ------------------------------------------ System Profile : Performance CPU Power Management : Maximum Performance Memory Frequency : Maximum Performance Turbo Boost : Enabled C1E : Disabled C States : Disabled Monitor/Mwait : Enabled Memory Patrol Scrub : Standard Memory Refresh Rate : 1x Memory Operating Voltage : Auto Collaborative CPU Performance Control : Disabled A Dell mailing list post describes the symptoms almost perfectly. Dell suggested that the author try using the Performance profile, but that didn't help. He ended up applying some settings in Dell's guide for configuring a server for low latency environments and one of those settings (or a combination thereof) seems to have fixed the problem. Kernel.org bug #36182 notes that power-limit interrupt debugging was enabled by default, which is causing performance degradation in scenarios where CPU voltage regulation is kicking in. A RHN KB article (RHN login required) mentions a problem impacting PE r620 and r720 servers not running the Performance profile, and recommends an update to a kernel released two weeks ago. ...Except we are running the Performance profile... Everything I can find online is running me in circles here. What's the heck is going on?

  Read the article

• Using pfSense, OpenVPN Connects but Still Can't See the Network

  - by nicorellius

  I am having an OpenVPN issue. I have a pfSense box at home configured to allow traffic through a VPN tunnel. The client computer is Windows XP Home, behind a standard Comcast connection and a Netgear wireless router. I use OpenVPN to access my work network (from where I am trying to get out of in this post) from home (with an XP Pro machine behind pfSense), and this works fine. The client config is similar but has the changes specific to my setup... Here is my XP Home config: client dev tun proto tcp remote pfsense.*.org 1194 (starred out by me) resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3 When I launch the OpenVPN GUI, the Tunnel TAP network connection turns red, and I can right-click that to connect to the server. Everything seems to work fine until I browse for the actual network. The Tunnel TAP connection turns green and it says connected to 10.1.1.6 (I have tried different IP pools here too with no luck). I can see the internal network fine, but my home network behind pfSense is not there. I have tried browsing there by using Tools Map Network Drive, using the browser, with no success. When I open the command line on the client and use the ipconfig -all command, I get the following: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TAP-Win32 Adapter V9 Physical Address. . . . . . . . . : *** (starred out by me) Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 10.1.1.6 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : DHCP Server . . . . . . . . . . . : 10.1.1.5 Lease Obtained. . . . . . . . . . : Monday, March 15, 2010 1:18:37 PM Lease Expires . . . . . . . . . . : Tuesday, March 15, 2011 1:18:37 PM I noticed that the default gateway is not present. Could this be my problem? I am still relatively new to firewalls, VPN, and network configuration so I'm sure I am messing up something simple. Oh yah, I should note that I have firewall rules configured for pfSense to allow traffic through the WAN and the LAN. At first there was just the WAN firewall rule, because that is what I got from the literature I was reading. I then created a LAN rule as well, but I'm not sure if this was correct. Neither way works, though. Screen shots below: Any help is much appreciated.

  Read the article

• Can't start httpd 2.4.9 with self-signed SSL certificate

  - by Smollet

  I cannot start the httpd 2.4.9 (tried 2.4.x too) on CentOS 6.5 with the simplest SSL config possible. The openssl version installed on the machine is OpenSSL 1.0.1e-fips 11 Feb 2013 (I've upgraded it using 'yum update' to the latest patched version as well) I have compiled and installed the httpd 2.4.9 using the following commands: ./configure --enable-ssl --with-ssl=/usr/local/ssl/ --enable-proxy=shared --enable-proxy_wstunnel=shared --with-apr=apr-1.5.1/ --with-apr-util=apr-util-1.5.3/ make make install Now I'm generating the default self-signed certificate as described in the CentOS HowTo: openssl genrsa -out ca.key 2048 openssl req -new -key ca.key -out ca.csr openssl x509 -req -days 365 -in ca.csr -signkey ca.key -out ca.crt cp ca.crt /etc/pki/tls/certs cp ca.key /etc/pki/tls/private/ca.key cp ca.csr /etc/pki/tls/private/ca.csr Here is my httpd-ssl.conf file: Listen 443 SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5 SSLPassPhraseDialog builtin SSLSessionCache "shmcb:/usr/local/apache2/logs/ssl_scache(512000)" SSLSessionCacheTimeout 300 <VirtualHost *:443> SSLEngine on SSLCertificateFile /etc/pki/tls/certs/ca.crt SSLCertificateKeyFile /etc/pki/tls/private/ca.key <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "/usr/local/apache2/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch "MSIE [2-5]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 CustomLog "/usr/local/apache2/logs/ssl_request_log" \ "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> when I start httpd using bin/apachectl -k start I get following errors in the error_log: Wed Jun 04 00:29:27.995654 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:29:27.995726 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.995863 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996111 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:29:27.996122 2014] [ssl:info] [pid 24021:tid 139640404293376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:29:27.996209 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.996280 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996295 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:29:27.996303 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: DH PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996308 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: EC PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996318 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:29:27.996321 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I then try to generate missing DH PARAMETERS and EC PARAMETERS: openssl dhparam -outform PEM -out dhparam.pem 2048 openssl ecparam -out ec_param.pem -name prime256v1 cat dhparam.pem ec_param.pem >> /etc/pki/tls/certs/ca.crt And it mitigates the error but the next comes out: [Wed Jun 04 00:34:05.021438 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:34:05.021487 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.021874 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022050 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:34:05.022066 2014] [ssl:info] [pid 24089:tid 140719371077376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:34:05.022285 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1016): AH02540: Custom DH parameters (2048 bits) for 192.168.9.128:443 loaded from /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022389 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1030): AH02541: ECDH curve prime256v1 for 192.168.9.128:443 specified in /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022397 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.022464 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022478 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:34:05.022488 2014] [ssl:emerg] [pid 24089:tid 140719371077376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:34:05.022491 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I have tried to generate the simple certificate/key pair exactly as described in the httpd docs Unfortunately, I still get exact same errors as above. I've seen a bug report with the similar issue: https://issues.apache.org/bugzilla/show_bug.cgi?id=56410 But the openssl version I have is reported as working there. I've also tried to apply the patch from the report as well as build the latest 2.4.x branch with no success, I get the same errors as above. I have also tried to create a short chain of certificates and set the root CA certificate using SSLCertificateChainFile directive. That didn't help either, I get exact same errors as above. I'm not interested in setting up hardened security, etc. The only thing I need is to start httpd with the simplest SSL config possible to continue testing proxy config for the mod_proxy_wstunnel Had anybody encountered and solved this issue? Is my sequence for creating a self-signed certificate incorrect? I'd appreciate any help very much!

  Read the article

• installed openstack using devstack install shell script but getting 500 error when i try opening dashboard

  - by Arvind

  I followed the instructions at http://devstack.org/guides/single-machine.html to install OpenStack. I first installed Ubuntu on my Windows 7 PC using the officially supported Windows installer for Ubuntu 12.04 LTS. And after that I followed the instructions at above page to install OpenStack. As per instructions, I should be able to access the dashboard aka Horizon, at http://192.168.1.4/ (thats the IP of the PC on which I installed Ubuntu-OpenStack). However I am getting a 500 error web page when I open that. How do I resolve this error? I want to set up a dev environment for OpenStack. For your ref, the whole error message is given now-- FilterError at / /usr/bin/env: node: No such file or directory Request Method: GET Request URL: http://192.168.1.4/ Django Version: 1.4.2 Exception Type: FilterError Exception Value: /usr/bin/env: node: No such file or directory Exception Location: /usr/local/lib/python2.7/dist-packages/compressor/filters/base.py in input, line 133 Python Executable: /usr/bin/python Python Version: 2.7.3 Python Path: ['/opt/stack/horizon/openstack_dashboard/wsgi/../..', '/opt/stack/python-keystoneclient', '/opt/stack/python-novaclient', '/opt/stack/python-openstackclient', '/opt/stack/keystone', '/opt/stack/glance', '/opt/stack/python-glanceclient/setuptools_git-0.4.2-py2.7.egg', '/opt/stack/python-glanceclient', '/opt/stack/nova', '/opt/stack/horizon', '/opt/stack/cinder', '/opt/stack/python-cinderclient', '/usr/local/lib/python2.7/dist-packages', '/usr/lib/python2.7', '/usr/lib/python2.7/plat-linux2', '/usr/lib/python2.7/lib-tk', '/usr/lib/python2.7/lib-old', '/usr/lib/python2.7/lib-dynload', '/usr/lib/python2.7/dist-packages', '/usr/lib/python2.7/dist-packages/PIL', '/usr/lib/python2.7/dist-packages/gst-0.10', '/usr/lib/python2.7/dist-packages/gtk-2.0', '/usr/lib/pymodules/python2.7', '/usr/lib/python2.7/dist-packages/ubuntu-sso-client', '/usr/lib/python2.7/dist-packages/ubuntuone-client', '/usr/lib/python2.7/dist-packages/ubuntuone-control-panel', '/usr/lib/python2.7/dist-packages/ubuntuone-couch', '/usr/lib/python2.7/dist-packages/ubuntuone-storage-protocol', '/opt/stack/horizon/openstack_dashboard'] Server time: Sat, 27 Oct 2012 08:43:29 +0000 Error during template rendering In template /opt/stack/horizon/openstack_dashboard/templates/_stylesheets.html, error at line 3 /usr/bin/env: node: No such file or directory 1 {% load compress %} 2 3 {% compress css %} 4 <link href='{{ STATIC_URL }}dashboard/less/horizon.less' type='text/less' media='screen' rel='stylesheet' /> 5 {% endcompress %} 6 7 <link rel="shortcut icon" href="{{ STATIC_URL }}dashboard/img/favicon.ico"/> 8 Also, the traceback is now given below-- Environment: Request Method: GET Request URL: http://192.168.1.4/ Django Version: 1.4.2 Python Version: 2.7.3 Installed Applications: ('openstack_dashboard', 'django.contrib.contenttypes', 'django.contrib.auth', 'django.contrib.sessions', 'django.contrib.messages', 'django.contrib.staticfiles', 'django.contrib.humanize', 'compressor', 'horizon', 'openstack_dashboard.dashboards.project', 'openstack_dashboard.dashboards.admin', 'openstack_dashboard.dashboards.settings', 'openstack_auth') Installed Middleware: ('django.middleware.common.CommonMiddleware', 'django.middleware.csrf.CsrfViewMiddleware', 'django.contrib.sessions.middleware.SessionMiddleware', 'django.contrib.auth.middleware.AuthenticationMiddleware', 'django.contrib.messages.middleware.MessageMiddleware', 'horizon.middleware.HorizonMiddleware', 'django.middleware.doc.XViewMiddleware', 'django.middleware.locale.LocaleMiddleware') Template error: In template /opt/stack/horizon/openstack_dashboard/templates/_stylesheets.html, error at line 3 /usr/bin/env: node: No such file or directory 1 : {% load compress %} 2 : 3 : {% compress css %} 4 : <link href='{{ STATIC_URL }}dashboard/less/horizon.less' type='text/less' media='screen' rel='stylesheet' /> 5 : {% endcompress %} 6 : 7 : <link rel="shortcut icon" href="{{ STATIC_URL }}dashboard/img/favicon.ico"/> 8 : Traceback: File "/usr/local/lib/python2.7/dist-packages/django/core/handlers/base.py" in get_response 111. response = callback(request, *callback_args, **callback_kwargs) File "/usr/local/lib/python2.7/dist-packages/django/views/decorators/vary.py" in inner_func 36. response = func(*args, **kwargs) File "/opt/stack/horizon/openstack_dashboard/wsgi/../../openstack_dashboard/views.py" in splash 38. return shortcuts.render(request, 'splash.html', {'form': form}) File "/usr/local/lib/python2.7/dist-packages/django/shortcuts/__init__.py" in render 44. return HttpResponse(loader.render_to_string(*args, **kwargs), File "/usr/local/lib/python2.7/dist-packages/django/template/loader.py" in render_to_string 176. return t.render(context_instance) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in render 140. return self._render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in _render 134. return self.nodelist.render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in render 823. bit = self.render_node(node, context) File "/usr/local/lib/python2.7/dist-packages/django/template/debug.py" in render_node 74. return node.render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/loader_tags.py" in render 155. return self.render_template(self.template, context) File "/usr/local/lib/python2.7/dist-packages/django/template/loader_tags.py" in render_template 137. output = template.render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in render 140. return self._render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in _render 134. return self.nodelist.render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in render 823. bit = self.render_node(node, context) File "/usr/local/lib/python2.7/dist-packages/django/template/debug.py" in render_node 74. return node.render(context) File "/usr/local/lib/python2.7/dist-packages/compressor/templatetags/compress.py" in render 147. return self.render_compressed(context, self.kind, self.mode, forced=forced) File "/usr/local/lib/python2.7/dist-packages/compressor/templatetags/compress.py" in render_compressed 107. rendered_output = self.render_output(compressor, mode, forced=forced) File "/usr/local/lib/python2.7/dist-packages/compressor/templatetags/compress.py" in render_output 119. return compressor.output(mode, forced=forced) File "/usr/local/lib/python2.7/dist-packages/compressor/css.py" in output 51. ret.append(subnode.output(*args, **kwargs)) File "/usr/local/lib/python2.7/dist-packages/compressor/css.py" in output 53. return super(CssCompressor, self).output(*args, **kwargs) File "/usr/local/lib/python2.7/dist-packages/compressor/base.py" in output 230. content = self.filter_input(forced) File "/usr/local/lib/python2.7/dist-packages/compressor/base.py" in filter_input 192. for hunk in self.hunks(forced): File "/usr/local/lib/python2.7/dist-packages/compressor/base.py" in hunks 167. precompiled, value = self.precompile(value, **options) File "/usr/local/lib/python2.7/dist-packages/compressor/base.py" in precompile 210. command=command, filename=filename).input(**kwargs) File "/usr/local/lib/python2.7/dist-packages/compressor/filters/base.py" in input 133. raise FilterError(err) Exception Type: FilterError at / Exception Value: /usr/bin/env: node: No such file or directory

  Read the article

• Nginx + php-fpm "504 Gateway Time-out" error with almost zero load (on a test-server)

  - by rahul286

  After debugging for 6-hours - I am giving this up :| We have a nginx+php-fpm+mysql in LAN with almost 100 wordpress (created and used by different designers/developers all working on test wordpres setup) We are using nginx without any issues from long. Today, all of a sudden - nginx started returning "504 Gateway Time-out" out of the blue... I checked nginx error log for a virtual host... 2010/09/06 21:24:24 [error] 12909#0: *349 upstream timed out (110: Connection timed out) while reading response header from upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET /favicon.ico HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 21:25:11 [error] 12909#0: *349 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET /favicon.ico HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 21:25:11 [error] 12909#0: *443 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET /info.php HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 21:25:12 [error] 12909#0: *443 connect() failed (111: Connection refused) while connecting to upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET /favicon.ico HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 22:08:32 [error] 12909#0: *1025 upstream timed out (110: Connection timed out) while reading response header from upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET / HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 22:09:33 [error] 12909#0: *1025 upstream timed out (110: Connection timed out) while reading response header from upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET /favicon.ico HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 22:09:40 [error] 12909#0: *1064 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET /info.php HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 22:09:40 [error] 12909#0: *1064 connect() failed (111: Connection refused) while connecting to upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET /favicon.ico HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 22:24:44 [error] 12909#0: *1313 upstream timed out (110: Connection timed out) while reading response header from upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET / HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" 2010/09/06 22:24:53 [error] 12909#0: *1313 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: 192.168.0.1, server: rahul286.rtcamp.info, request: "GET /favicon.ico HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "rahul286.rtcamp.info" As I run php-fpm on port 9000 via TCP mode, I ran "netstat | grep 9000" and noticed something unusual... (Pasting partial output here for ease of read) tcp 9 0 localhost:9000 localhost:36094 CLOSE_WAIT 14269/php5-fpm tcp 0 0 localhost:46664 localhost:9000 FIN_WAIT2 - tcp 1257 0 localhost:9000 localhost:36135 CLOSE_WAIT - tcp 1257 0 localhost:9000 localhost:36125 CLOSE_WAIT - tcp 9 0 localhost:9000 localhost:36102 CLOSE_WAIT 14268/php5-fpm tcp 0 0 localhost:46662 localhost:9000 FIN_WAIT2 - tcp 745 0 localhost:9000 localhost:46644 CLOSE_WAIT - tcp 0 0 localhost:46658 localhost:9000 FIN_WAIT2 - tcp 1265 0 localhost:9000 localhost:46607 CLOSE_WAIT - tcp 0 0 localhost:46672 localhost:9000 ESTABLISHED 12909/nginx: worker tcp 1257 0 localhost:9000 localhost:36119 CLOSE_WAIT - tcp 1265 0 localhost:9000 localhost:46613 CLOSE_WAIT - tcp 0 0 localhost:46646 localhost:9000 FIN_WAIT2 - tcp 1257 0 localhost:9000 localhost:36137 CLOSE_WAIT - tcp 0 0 localhost:46670 localhost:9000 ESTABLISHED 12909/nginx: worker tcp 1265 0 localhost:9000 localhost:46619 CLOSE_WAIT - tcp 1336 0 localhost:9000 localhost:46668 ESTABLISHED - tcp 0 0 localhost:46648 localhost:9000 FIN_WAIT2 - tcp 1336 0 localhost:9000 localhost:46670 ESTABLISHED - tcp 9 0 localhost:9000 localhost:36108 CLOSE_WAIT 14274/php5-fpm tcp 1336 0 localhost:9000 localhost:46684 ESTABLISHED - tcp 0 0 localhost:46674 localhost:9000 ESTABLISHED 12909/nginx: worker tcp 1336 0 localhost:9000 localhost:46666 ESTABLISHED - tcp 1257 0 localhost:9000 localhost:46648 CLOSE_WAIT - tcp 1336 0 localhost:9000 localhost:46678 ESTABLISHED - tcp 0 0 localhost:46668 localhost:9000 ESTABLISHED 12909/nginx: wo There are plenty of "CLOSE_WAIT" & "FIN_WAIT2" pairs as highlighted below (in above output): tcp 1337 0 localhost:9000 localhost:46680 CLOSE_WAIT - tcp 0 0 localhost:46680 localhost:9000 FIN_WAIT2 - Please note port 46680 in above. I enabled mysql slow queries error log, but it didn't work. As of now restarting php5-fpm every minute via a cronjob (see command below) keeping everything running "smoothly" but I hate patchwork and want to solve this... 1 * * * * service php5-fpm restart > /dev/null I searched extensively on Google - got no help. As mentioned, this a test-server in LAN, CPU load is never crossed 0.10 and memory usage is also below 25% (System has 2GB RAM and ubuntu-server installed) So if you find its time-confusing to help me out, please atleast drop a hint. Thanks in advance for help. -Rahul (note - this is reposting of - http://forum.nginx.org/read.php?11,127694) Update: I found answer, which is posted below.

  Read the article

• Credentials can not be delegated - Alfresco Share

  - by leftcase

  I've hit a brick wall configuring Alfresco 4.0.d on Redhat 6. I'm using Kerberos authentication, it seems to be working normally, and single sign on is working on the main alfresco app itself. I've been through the configuration steps to get the share app working, but try as I may, I keep getting this error in catalina.out each time a browser accesses http://server:8080/share along with a 'Windows Security' password box. WARN [site.servlet.KerberosSessionSetupPrivilegedAction] credentials can not be delegated! Here's what I've done so far: Using AD users and computers, selected the alfrescohttp account, and selected 'trust this user for delegation to any service (Kerberos only). Copied /opt/alfresco-4.0.d/tomcat/shared/classes/alfresco/web-extension/share-config-custom.xml.sample to share-config-custom.xml and edited like this: <config evaluator="string-compare" condition="Kerberos" replace="true"> <kerberos> <password>*****</password> <realm>MYDOMAIN.CO.UK</realm> <endpoint-spn>HTTP/[email protected]</endpoint-spn> <config-entry>ShareHTTP</config-entry> </kerberos> </config> <config evaluator="string-compare" condition="Remote"> <remote> <keystore> <path>alfresco/web-extension/alfresco-system.p12</path> <type>pkcs12</type> <password>alfresco-system</password> </keystore> <connector> <id>alfrescoCookie</id> <name>Alfresco Connector</name> <description>Connects to an Alfresco instance using cookie-based authentication</description> <class>org.springframework.extensions.webscripts.connector.AlfrescoConnector</class> </connector> <endpoint> <id>alfresco</id> <name>Alfresco - user access</name> <description>Access to Alfresco Repository WebScripts that require user authentication</description> <connector-id>alfrescoCookie</connector-id> <endpoint-url>http://localhost:8080/alfresco/wcs</endpoint-url> <identity>user</identity> <external-auth>true</external-auth> </endpoint> </remote> </config> Setup the /etc/krb5.conf file like this: [logging] default = FILE:/var/log/krb5libs.log kdc = FILE:/var/log/krb5kdc.log admin_server = FILE:/var/log/kadmind.log [libdefaults] default_realm = MYDOMAIN.CO.UK default_tkt_enctypes = rc4-hmac default_tgs_enctypes = rc4-hmac forwardable = true proxiable = true [realms] MYDOMAIN.CO.UK = { kdc = mydc.mydomain.co.uk admin_server = mydc.mydomain.co.uk } [domain_realm] .mydc.mydomain.co.uk = MYDOMAIN.CO.UK mydc.mydomain.co.uk = MYDOMAIN.CO.UK /opt/alfresco-4.0.d/java/jre/lib/security/java.login.config is configured like this: Alfresco { com.sun.security.auth.module.Krb5LoginModule sufficient; }; AlfrescoCIFS { com.sun.security.auth.module.Krb5LoginModule required storeKey=true useKeyTab=true keyTab="/etc/alfrescocifs.keytab" principal="cifs/server.mydomain.co.uk"; }; AlfrescoHTTP { com.sun.security.auth.module.Krb5LoginModule required storeKey=true useKeyTab=true keyTab="/etc/alfrescohttp.keytab" principal="HTTP/server.mydomain.co.uk"; }; com.sun.net.ssl.client { com.sun.security.auth.module.Krb5LoginModule sufficient; }; other { com.sun.security.auth.module.Krb5LoginModule sufficient; }; ShareHTTP { com.sun.security.auth.module.Krb5LoginModule required storeKey=true useKeyTab=true keyTab="/etc/alfrescohttp.keytab" principal="HTTP/server.mydomain.co.uk"; }; And finally, the following settings in alfresco-global.conf authentication.chain=kerberos1:kerberos,alfrescoNtlm1:alfrescoNtlm kerberos.authentication.real=MYDOMAIN.CO.UK kerberos.authentication.user.configEntryName=Alfresco kerberos.authentication.cifs.configEntryName=AlfrescoCIFS kerberos.authentication.http.configEntryName=AlfrescoHTTP kerberos.authentication.cifs.password=****** kerberos.authentication.http.password=***** kerberos.authentication.defaultAdministratorUserNames=administrator ntlm.authentication.sso.enabled=true As I say, I've hit a brick wall with this and I'd really appreciate any help you can give me! This question is also posted on the Alfresco forum, but I wondered if any folk here on serverfault have come across similar implementation challenges?

  Read the article

• Configure PERL DBI and DBD in Linux

  - by Balualways

  I am new to Perl and I work in a Linux OEL 5x server. I am trying to configure the Perl DB modules for Oracle connectivity (DBD and DBI modules). Can anyone help me out in the installation procedure? I had tried CPAN didn't really worked out. Any help would be appreciated. I am not quite sure I need to initialize any variables other than $LD_LIBRARY_PATH and $ORACLE_HOME These are my observations: ISSUE:: I am getting the following issue while using the DBI module to connect to Oracle: install_driver(Oracle) failed: Can't locate loadable object for module DBD::Oracle in @INC (@INC contains: /usr/lib64/perl5/site_perl/5.8.8/x86_64-linux-thread-multi /usr/lib/perl5/site_perl/5.8.8 /usr/lib/perl5/site_perl /usr/lib64/perl5/vendor_perl/5.8.8/x86_64-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.8 /usr/lib/perl5/vendor_perl /usr/lib64/perl5/5.8.8/x86_64-linux-thread-multi /usr/lib/perl5/5.8.8 .) at (eval 3) line 3 Compilation failed in require at (eval 3) line 3. Perhaps a module that DBD::Oracle requires hasn't been fully installed at connectdb.pl line 57 I had installed the DBD for oracle from /usr/lib64/perl5/5.8.8/x86_64-linux-thread-multi/DBD/DBD-Oracle-1.50 Could you please take a look into the steps and correct me if I am wrong: Observations: $ echo $LD_LIBRARY_PATH /opt/CA/UnicenterAutoSysJM/autosys/lib:/opt/CA/SharedComponents/Csam/SockAdapter/lib:/opt/CA/SharedComponents/ETPKI/lib:/opt/CA/CAlib $ echo $ORACLE_HOME /usr/local/oracle/ORA This is how I tried to install the DBD module: Download the file DBD 1.50 for Oracle Copy to /usr/lib64/perl5/5.8.8/x86_64-linux-thread-multi/DBD Untar and Makefile.PL . Message: Using DBI 1.52 (for perl 5.008008 on x86_64-linux-thread-multi) installed in /usr/lib64/perl5/vendor_perl/5.8.8/x86_64-linux-thread-multi/auto/DBI/ Configuring DBD::Oracle for perl 5.008008 on linux (x86_64-linux-thread-multi) Remember to actually *READ* the README file! Especially if you have any problems. Installing on a linux, Ver#2.6 Using Oracle in /opt/oracle/product/10.2 DEFINE _SQLPLUS_RELEASE = "1002000400" (CHAR) Oracle version 10.2.0.4 (10.2) Found /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk Found /opt/oracle/product/10.2/rdbms/demo/demo_rdbms64.mk Found /opt/oracle/product/10.2/rdbms/lib/ins_rdbms.mk Using /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk Your LD_LIBRARY_PATH env var is set to '/usr/local/oracle/ORA/lib:/usr/dt/lib:/usr/openwin/lib:/usr/local/oracle/ORA/ows/cartx/wodbc/1.0/util/lib:/usr/local/oracle/ORA/lib:/usr/local/sybase/OCS-12_0/lib:/usr/local/sybase/lib:/home/oracle/jdbc/jdbcoci73/lib:./' WARNING: Your LD_LIBRARY_PATH env var doesn't include '/opt/oracle/product/10.2/lib' but probably needs to. Reading /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk Reading /usr/local/oracle/ORA/rdbms/lib/env_rdbms.mk Attempting to discover Oracle OCI build rules sh: make: command not found by executing: [make -f /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk build ECHODO=echo ECHO=echo GENCLNTSH='echo genclntsh' CC=true OPTIMIZE= CCFLAGS= EXE=DBD_ORA_EXE OBJS=DBD_ORA_OBJ.o] WARNING: Oracle build rule discovery failed (32512) Add path to make command into your PATH environment variable. Oracle oci build prolog: [sh: make: command not found] Oracle oci build command: [] WARNING: Unable to interpret Oracle build commands from /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk. (Will continue by using fallback approach.) Please report this to dbi-users@perl.org. See README for what to include. Found header files in /opt/oracle/product/10.2/rdbms/public. client_version=10.2 DEFINE= -Wall -Wno-comment -DUTF8_SUPPORT -DORA_OCI_VERSION=\"10.2.0.4\" -DORA_OCI_102 Checking for functioning wait.ph System: perl5.008008 linux ca-build9.us.oracle.com 2.6.20-1.3002.fc6xen #1 smp thu apr 30 18:08:39 pdt 2009 x86_64 x86_64 x86_64 gnulinux Compiler: gcc -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -D_REENTRANT -D_GNU_SOURCE -fno-strict-aliasing -pipe -Wdeclaration-after-statement -I/usr/local/include -D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 -I/usr/include/gdbm Linker: not found Sysliblist: -ldl -lm -lpthread -lnsl -lirc Oracle makefiles would have used these definitions but we override them: CC: cc CFLAGS: $(GFLAG) $(OPTIMIZE) $(CDEBUG) $(CCFLAGS) $(PFLAGS)\ $(SHARED_CFLAG) $(USRFLAGS) [$(GFLAG) -O3 $(CDEBUG) -m32 $(TRIGRAPHS_CCFLAGS) -fPIC -I/usr/local/oracle/ORA/rdbms/demo -I/usr/local/oracle/ORA/rdbms/public -I/usr/local/oracle/ORA/plsql/public -I/usr/local/oracle/ORA/network/public -DLINUX -D_GNU_SOURCE -D_LARGEFILE64_SOURCE=1 -D_LARGEFILE_SOURCE=1 -DSLTS_ENABLE -DSLMXMX_ENABLE -D_REENTRANT -DNS_THREADS -fno-strict-aliasing $(LPFLAGS) $(USRFLAGS)] build: $(CC) $(ORALIBPATH) -o $(EXE) $(OBJS) $(OCISHAREDLIBS) [ cc -L$(LIBHOME) -L/usr/local/oracle/ORA/rdbms/lib/ -o $(EXE) $(OBJS) -lclntsh $(EXPDLIBS) $(EXOSLIBS) -ldl -lm -lpthread -lnsl -lirc -ldl -lm $(USRLIBS) -lpthread] LDFLAGS: $(LDFLAGS32) [-m32 -o $@ -L/usr/local/oracle/ORA/rdbms//lib32/ -L/usr/local/oracle/ORA/lib32/ -L/usr/local/oracle/ORA/lib32/stubs/] Linking with /usr/local/oracle/ORA/rdbms/lib/defopt.o -lclntsh -ldl -lm -lpthread -lnsl -lirc -ldl -lm -lpthread [from $(DEF_OPT) $(OCISHAREDLIBS)] Checking if your kit is complete... Looks good LD_RUN_PATH=/usr/local/oracle/ORA/lib Using DBD::Oracle 1.50. Using DBD::Oracle 1.50. Using DBI 1.52 (for perl 5.008008 on x86_64-linux-thread-multi) installed in /usr/lib64/perl5/vendor_perl/5.8.8/x86_64-linux-thread-multi/auto/DBI/ Writing Makefile for DBD::Oracle Writing MYMETA.yml and MYMETA.json *** If you have problems... read all the log printed above, and the README and README.help.txt files. (Of course, you have read README by now anyway, haven't you?)

  Read the article

• Installing nGinX Reverse Proxy on CentOS 5

  - by heavymark

  I'm trying to install nGinX as a reverse proxy on CentOS 5 with apache. The instructions to do this are here: http://wiki.mediatemple.net/w/(dv):Configure_nginx_as_reverse_proxy_web_server Note- in the instructions, for the url to get nginx I'm using the following: http://nginx.org/download/nginx-1.0.10.tar.gz Now here is my problem. After installing the required packages and running .configure I get the following: checking for OS + Linux 2.6.18-028stab094.3 x86_64 checking for C compiler ... found + using GNU C compiler + gcc version: 4.1.2 20080704 (Red Hat 4.1.2-51) checking for gcc -pipe switch ... found checking for gcc builtin atomic operations ... found checking for C99 variadic macros ... found checking for gcc variadic macros ... found checking for unistd.h ... found checking for inttypes.h ... found checking for limits.h ... found checking for sys/filio.h ... not found checking for sys/param.h ... found checking for sys/mount.h ... found checking for sys/statvfs.h ... found checking for crypt.h ... found checking for Linux specific features checking for epoll ... found checking for sendfile() ... found checking for sendfile64() ... found checking for sys/prctl.h ... found checking for prctl(PR_SET_DUMPABLE) ... found checking for sched_setaffinity() ... found checking for crypt_r() ... found checking for sys/vfs.h ... found checking for nobody group ... found checking for poll() ... found checking for /dev/poll ... not found checking for kqueue ... not found checking for crypt() ... not found checking for crypt() in libcrypt ... found checking for F_READAHEAD ... not found checking for posix_fadvise() ... found checking for O_DIRECT ... found checking for F_NOCACHE ... not found checking for directio() ... not found checking for statfs() ... found checking for statvfs() ... found checking for dlopen() ... not found checking for dlopen() in libdl ... found checking for sched_yield() ... found checking for SO_SETFIB ... not found checking for SO_ACCEPTFILTER ... not found checking for TCP_DEFER_ACCEPT ... found checking for accept4() ... not found checking for int size ... 4 bytes checking for long size ... 8 bytes checking for long long size ... 8 bytes checking for void * size ... 8 bytes checking for uint64_t ... found checking for sig_atomic_t ... found checking for sig_atomic_t size ... 4 bytes checking for socklen_t ... found checking for in_addr_t ... found checking for in_port_t ... found checking for rlim_t ... found checking for uintptr_t ... uintptr_t found checking for system endianess ... little endianess checking for size_t size ... 8 bytes checking for off_t size ... 8 bytes checking for time_t size ... 8 bytes checking for setproctitle() ... not found checking for pread() ... found checking for pwrite() ... found checking for sys_nerr ... found checking for localtime_r() ... found checking for posix_memalign() ... found checking for memalign() ... found checking for mmap(MAP_ANON|MAP_SHARED) ... found checking for mmap("/dev/zero", MAP_SHARED) ... found checking for System V shared memory ... found checking for POSIX semaphores ... not found checking for POSIX semaphores in libpthread ... found checking for struct msghdr.msg_control ... found checking for ioctl(FIONBIO) ... found checking for struct tm.tm_gmtoff ... found checking for struct dirent.d_namlen ... not found checking for struct dirent.d_type ... found checking for PCRE library ... found checking for system md library ... not found checking for system md5 library ... not found checking for OpenSSL md5 crypto library ... found checking for sha1 in system md library ... not found checking for OpenSSL sha1 crypto library ... found checking for zlib library ... found creating objs/Makefile Configuration summary + using system PCRE library + OpenSSL library is not used + md5: using system crypto library + sha1: using system crypto library + using system zlib library nginx path prefix: "/usr/local/nginx" nginx binary file: "/usr/local/nginx/sbin/nginx" nginx configuration prefix: "/usr/local/nginx/conf" nginx configuration file: "/usr/local/nginx/conf/nginx.conf" nginx pid file: "/usr/local/nginx/logs/nginx.pid" nginx error log file: "/usr/local/nginx/logs/error.log" nginx http access log file: "/usr/local/nginx/logs/access.log" nginx http client request body temporary files: "client_body_temp" nginx http proxy temporary files: "proxy_temp" nginx http fastcgi temporary files: "fastcgi_temp" nginx http uwsgi temporary files: "uwsgi_temp" nginx http scgi temporary files: "scgi_temp" It says if you get errors to stop and make sure packages are installed. I didn't get errors but as you can see I got several "not founds". Are those considered errors? If so how do I resolve that. And as noted in the link, I cannot install through yum, because it wont work with plesk then. Thanks!

  Read the article

• UnicodeEncodeError when uploading files in Django admin

  - by Samuel Linde

  Note: I asked this question on StackOverflow, but I realize this might be a more proper place to ask this kind of question. I'm trying to upload a file called 'Testaråäö.txt' via the Django admin app. I'm running Django 1.3.1 with Gunicorn 0.13.4 and Nginx 0.7.6.7 on a Debian 6 server. Database is PostgreSQL 8.4.9. Other Unicode data is saved to the database with no problem, so I guess the problem must be with the filesystem somehow. I've set http { charset utf-8; } in my nginx.conf. LC_ALL and LANG is set to 'sv_SE.UTF-8'. Running 'locale' verifies this. I even tried setting LC_ALL and LANG in my nginx init script just to make sure locale is set properly. Here's the traceback: Traceback (most recent call last): File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/core/handlers/base.py", line 111, in get_response response = callback(request, *callback_args, **callback_kwargs) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/contrib/admin/options.py", line 307, in wrapper return self.admin_site.admin_view(view)(*args, **kwargs) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/utils/decorators.py", line 93, in _wrapped_view response = view_func(request, *args, **kwargs) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/views/decorators/cache.py", line 79, in _wrapped_view_func response = view_func(request, *args, **kwargs) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/contrib/admin/sites.py", line 197, in inner return view(request, *args, **kwargs) File "/srv/django/letebo/app/cms/admin.py", line 81, in change_view return super(PageAdmin, self).change_view(request, obj_id) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/utils/decorators.py", line 28, in _wrapper return bound_func(*args, **kwargs) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/utils/decorators.py", line 93, in _wrapped_view response = view_func(request, *args, **kwargs) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/utils/decorators.py", line 24, in bound_func return func(self, *args2, **kwargs2) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/db/transaction.py", line 217, in inner res = func(*args, **kwargs) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/contrib/admin/options.py", line 985, in change_view self.save_formset(request, form, formset, change=True) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/contrib/admin/options.py", line 677, in save_formset formset.save() File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/forms/models.py", line 482, in save return self.save_existing_objects(commit) + self.save_new_objects(commit) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/forms/models.py", line 613, in save_new_objects self.new_objects.append(self.save_new(form, commit=commit)) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/forms/models.py", line 717, in save_new obj.save() File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/db/models/base.py", line 460, in save self.save_base(using=using, force_insert=force_insert, force_update=force_update) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/db/models/base.py", line 504, in save_base self.save_base(cls=parent, origin=org, using=using) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/db/models/base.py", line 543, in save_base for f in meta.local_fields if not isinstance(f, AutoField)] File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/db/models/fields/files.py", line 255, in pre_save file.save(file.name, file, save=False) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/db/models/fields/files.py", line 92, in save self.name = self.storage.save(name, content) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/core/files/storage.py", line 48, in save name = self.get_available_name(name) File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/core/files/storage.py", line 74, in get_available_name while self.exists(name): File "/srv/.virtualenvs/letebo/lib/python2.6/site-packages/django/core/files/storage.py", line 218, in exists return os.path.exists(self.path(name)) File "/srv/.virtualenvs/letebo/lib/python2.6/genericpath.py", line 18, in exists st = os.stat(path) UnicodeEncodeError: 'ascii' codec can't encode characters in position 52-54: ordinal not in range(128) I tried running Gunicorn with debugging turned on, and the file uploads without any problem at all. I suppose this must mean that the issue is with Nginx. Still beats me where to look, though. Here are the raw response headers from Gunicorn and Nginx, if it makes any sense: Gunicorn: HTTP/1.1 302 FOUND Server: gunicorn/0.13.4 Date: Thu, 09 Feb 2012 14:50:27 GMT Connection: close Transfer-Encoding: chunked Expires: Thu, 09 Feb 2012 14:50:27 GMT Vary: Cookie Last-Modified: Thu, 09 Feb 2012 14:50:27 GMT Location: http://my-server.se:8000/admin/cms/page/15/ Cache-Control: max-age=0 Content-Type: text/html; charset=utf-8 Set-Cookie: messages="yada yada yada"; Path=/ Nginx: HTTP/1.1 500 INTERNAL SERVER ERROR Server: nginx/0.7.67 Date: Thu, 09 Feb 2012 14:50:57 GMT Content-Type: text/html; charset=utf-8 Transfer-Encoding: chunked Connection: close Vary: Cookie 500 UPDATE: Both locale.getpreferredencoding() and sys.getfilesystemencoding() outputs 'UTF-8'. locale.getdefaultlocale() outputs ('sv_SE', 'UTF8'). This seem correct to me, so I'm still not sure why I keep getting these errors.

  Read the article

• SSH is not working .. Password promt is not coming

  - by Sumanth Lingappa

  I am not able to SSH into my ubuntu server since yesterday. I am not using any keyless or public key method.. Its simple SSH with username and password everytime.. However I can do a VNC session running on my ubuntu server.. But I am afraid that if the vnc session goes out, I wont be having any way to login to the server.. My ssh-vvv output is as below.. sumanth@sumanth:~$ ssh -vvv user@serverIP OpenSSH_6.6.1, OpenSSL 1.0.1f 6 Jan 2014 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 172.16.2.156 [172.16.2.156] port 22. debug1: Connection established. debug1: identity file /home/sumanth/.ssh/id_rsa type -1 debug1: identity file /home/sumanth/.ssh/id_rsa-cert type -1 debug1: identity file /home/sumanth/.ssh/id_dsa type -1 debug1: identity file /home/sumanth/.ssh/id_dsa-cert type -1 debug1: identity file /home/sumanth/.ssh/id_ecdsa type -1 debug1: identity file /home/sumanth/.ssh/id_ecdsa-cert type -1 debug1: identity file /home/sumanth/.ssh/id_ed25519 type -1 debug1: identity file /home/sumanth/.ssh/id_ed25519-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH_5* compat 0x0c000000 debug2: fd 3 setting O_NONBLOCK debug3: load_hostkeys: loading entries for host "172.16.2.156" from file "/home/sumanth/.ssh/known_hosts" debug3: load_hostkeys: found key type ECDSA in file /home/sumanth/.ssh/known_hosts:5 debug3: load_hostkeys: loaded 1 keys debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: curve25519-sha256@libssh.org,ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,[email protected],[email protected],[email protected],[email protected],[email protected],ssh-ed25519,ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,[email protected],[email protected],[email protected],aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,[email protected],[email protected],[email protected],aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-md5,hmac-sha1,[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],[email protected],hmac-md5,hmac-sha1,[email protected],[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: setup hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: setup hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: ECDSA ea:4e:15:52:15:dd:6b:09:d4:36:cb:14:2d:c3:1b:7a debug3: load_hostkeys: loading entries for host "172.16.2.156" from file "/home/sumanth/.ssh/known_hosts" debug3: load_hostkeys: found key type ECDSA in file /home/sumanth/.ssh/known_hosts:5 debug3: load_hostkeys: loaded 1 keys debug1: Host '172.16.2.156' is known and matches the ECDSA host key. debug1: Found key in /home/sumanth/.ssh/known_hosts:5 debug1: ssh_ecdsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/sumanth/.ssh/id_rsa ((nil)), debug2: key: /home/sumanth/.ssh/id_dsa ((nil)), debug2: key: /home/sumanth/.ssh/id_ecdsa ((nil)), debug2: key: /home/sumanth/.ssh/id_ed25519 ((nil)),

  Read the article

• 500 Internal Server Error with PHP application

  - by James

  I have written a PHP application using Windows and XAMPP. I've been trying to run it on Ubuntu 10.10 with Lighttpd 1.4.26. Parts of the application work fine, but whenever I try to log in, I get a 500 - Internal Server Error page. The only thing that shows up in /var/log/lighttpd/error.log is 2011-02-25 13:43:13: (mod_fastcgi.c.2582) unexpected end-of-file (perhaps the fastcgi process died): pid: 1169 socket: unix:/tmp/php.socket-0 2011-02-25 13:43:13: (mod_fastcgi.c.3367) response not received, request sent: 1596 on socket: unix:/tmp/php.socket-0 for /~denton/customer-facing-portal/index.php?, closing connection If I had any output whatsoever from PHP, this would be a lot easier to debug. Any ideas on how to get some? Here is my /etc/lighttpd/lighttpd.conf file: # Debian lighttpd configuration file # ############ Options you really have to take care of #################### ## modules to load server.modules = ( "mod_alias", "mod_compress", # "mod_rewrite", # "mod_redirect", # "mod_usertrack", # "mod_expire", # "mod_flv_streaming", # "mod_evasive", "mod_setenv" ) ## a static document-root, for virtual-hosting take look at the ## server.virtual-* options server.document-root = "/var/www/" ## where to upload files to, purged daily. server.upload-dirs = ( "/var/cache/lighttpd/uploads" ) ## where to send error-messages to server.errorlog = "/var/log/lighttpd/error.log" ## files to check for if .../ is requested index-file.names = ( "index.php", "index.html", "index.htm", "default.htm", "index.lighttpd.html" ) ## Use the "Content-Type" extended attribute to obtain mime type if possible # mimetype.use-xattr = "enable" ## # which extensions should not be handle via static-file transfer # # .php, .pl, .fcgi are most often handled by mod_fastcgi or mod_cgi static-file.exclude-extensions = ( ".php", ".pl", ".fcgi" ) ######### Options that are good to be but not neccesary to be changed ####### ## Use ipv6 only if available. (disabled for while, check #560837) #include_shell "/usr/share/lighttpd/use-ipv6.pl" ## bind to port (default: 80) # server.port = 81 ## bind to localhost only (default: all interfaces) ## server.bind = "localhost" ## error-handler for status 404 #server.error-handler-404 = "/error-handler.html" #server.error-handler-404 = "/error-handler.php" ## to help the rc.scripts server.pid-file = "/var/run/lighttpd.pid" ## ## Format: <errorfile-prefix><status>.html ## -> ..../status-404.html for 'File not found' #server.errorfile-prefix = "/var/www/" ## virtual directory listings dir-listing.encoding = "utf-8" server.dir-listing = "enable" ### only root can use these options # # chroot() to directory (default: no chroot() ) #server.chroot = "/" ## change uid to <uid> (default: don't change) server.username = "www-data" ## change gid to <gid> (default: don't change) server.groupname = "www-data" #### compress module compress.cache-dir = "/var/cache/lighttpd/compress/" compress.filetype = ("text/plain", "text/html", "application/x-javascript", "text/css") #### url handling modules (rewrite, redirect, access) # url.rewrite = ( "^/$" => "/server-status" ) # url.redirect = ( "^/wishlist/(.+)" => "http://www.123.org/$1" ) #### expire module # expire.url = ( "/buggy/" => "access 2 hours", "/asdhas/" => "access plus 1 seconds 2 minutes") #### external configuration files ## mimetype mapping include_shell "/usr/share/lighttpd/create-mime.assign.pl" ## load enabled configuration files, ## read /etc/lighttpd/conf-available/README first include_shell "/usr/share/lighttpd/include-conf-enabled.pl" ## Set environment variables setenv.add-environment = ( "DB_URL__DEMO" => "192.168.1.231", "DB_NAME_DEMO" => "demo", "DB_USER_DEMO" => "user", "DB_PASS_DEMO" => "password", "DB_AGENCY_DEMO" => "demo" ) Here is my /etc/php5/cgi/php.ini file (sans 1641 lines of comments): [PHP] register_long_arrays = Off short_open_tag = Off engine = On short_open_tag = Off asp_tags = Off precision = 14 y2k_compliance = On output_buffering = 4096 zlib.output_compression = Off implicit_flush = Off unserialize_callback_func = serialize_precision = 100 allow_call_time_pass_reference = Off safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH disable_functions = disable_classes = expose_php = On max_execution_time = 30 max_input_time = 60 memory_limit = 128M error_reporting = E_ALL & ~E_DEPRECATED & ~E_STRICT display_errors = On display_startup_errors = On log_errors = On log_errors_max_len = 1024 ignore_repeated_errors = Off ignore_repeated_source = Off report_memleaks = On track_errors = On html_errors = On variables_order = "GPCS" request_order = "GP" register_globals = Off register_long_arrays = Off register_argc_argv = Off auto_globals_jit = On post_max_size = 8M magic_quotes_gpc = Off magic_quotes_runtime = Off magic_quotes_sybase = Off auto_prepend_file = auto_append_file = default_mimetype = "text/html" doc_root = user_dir = enable_dl = Off cgi.fix_pathinfo=1 file_uploads = On upload_max_filesize = 2M max_file_uploads = 20 allow_url_fopen = On allow_url_include = Off default_socket_timeout = 60 [Date] date.timezone = "America/Chicago" [filter] [iconv] [intl] [sqlite] [sqlite3] [Pcre] [Pdo] [Pdo_mysql] pdo_mysql.cache_size = 2000 pdo_mysql.default_socket= [Phar] [Syslog] define_syslog_variables = Off [mail function] SMTP = localhost smtp_port = 25 mail.add_x_header = On [SQL] sql.safe_mode = Off [ODBC] odbc.allow_persistent = On odbc.check_persistent = On odbc.max_persistent = -1 odbc.max_links = -1 odbc.defaultlrl = 4096 odbc.defaultbinmode = 1 [Interbase] ibase.allow_persistent = 1 ibase.max_persistent = -1 ibase.max_links = -1 ibase.timestampformat = "%Y-%m-%d %H:%M:%S" ibase.dateformat = "%Y-%m-%d" ibase.timeformat = "%H:%M:%S" [MySQL] mysql.allow_local_infile = On mysql.allow_persistent = On mysql.cache_size = 2000 mysql.max_persistent = -1 mysql.max_links = -1 mysql.default_port = mysql.default_socket = mysql.default_host = mysql.default_user = mysql.default_password = mysql.connect_timeout = 60 mysql.trace_mode = Off [MySQLi] mysqli.max_persistent = -1 mysqli.allow_persistent = On mysqli.max_links = -1 mysqli.cache_size = 2000 mysqli.default_port = 3306 mysqli.default_socket = mysqli.default_host = mysqli.default_user = mysqli.default_pw = mysqli.reconnect = Off [mysqlnd] mysqlnd.collect_statistics = On mysqlnd.collect_memory_statistics = Off [OCI8] [PostgresSQL] pgsql.allow_persistent = On pgsql.auto_reset_persistent = Off pgsql.max_persistent = -1 pgsql.max_links = -1 pgsql.ignore_notice = 0 pgsql.log_notice = 0 [Sybase-CT] sybct.allow_persistent = On sybct.max_persistent = -1 sybct.max_links = -1 sybct.min_server_severity = 10 sybct.min_client_severity = 10 [bcmath] bcmath.scale = 0 [browscap] [Session] session.save_handler = files session.use_cookies = 1 session.use_only_cookies = 1 session.name = PHPSESSID session.auto_start = 0 session.cookie_lifetime = 0 session.cookie_path = / session.cookie_domain = session.cookie_httponly = session.serialize_handler = php session.gc_probability = 1 session.gc_divisor = 1000 session.gc_maxlifetime = 1440 session.bug_compat_42 = Off session.bug_compat_warn = Off session.referer_check = session.entropy_length = 0 session.cache_limiter = nocache session.cache_expire = 180 session.use_trans_sid = 0 session.hash_function = 0 session.hash_bits_per_character = 5 url_rewriter.tags = "a=href,area=href,frame=src,input=src,form=fakeentry" [MSSQL] mssql.allow_persistent = On mssql.max_persistent = -1 mssql.max_links = -1 mssql.min_error_severity = 10 mssql.min_message_severity = 10 mssql.compatability_mode = Off mssql.secure_connection = Off [Assertion] [COM] [mbstring] [gd] [exif] [Tidy] tidy.clean_output = Off [soap] soap.wsdl_cache_enabled=1 soap.wsdl_cache_dir="/tmp" soap.wsdl_cache_ttl=86400 soap.wsdl_cache_limit = 5 [sysvshm] [ldap] ldap.max_links = -1 [mcrypt] [dba] Update: here is /etc/lighttpd/conf-enabled/15-fastcgi-php.conf As far as I know, it's just the default config file the Ubuntu package installed. ## FastCGI programs have the same functionality as CGI programs, ## but are considerably faster through lower interpreter startup ## time and socketed communication ## ## Documentation: /usr/share/doc/lighttpd-doc/fastcgi.txt.gz ## http://redmine.lighttpd.net/projects/lighttpd/wiki/Docs:ConfigurationOptions#mod_fastcgi-fastcgi ## Start an FastCGI server for php (needs the php5-cgi package) fastcgi.server += ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 1, "idle-timeout" => 20, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "4", "PHP_FCGI_MAX_REQUESTS" => "10000" ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" )) )

  Read the article

• Two network interfaces and two IP addresses on the same subnet in Linux

  - by Scott Duckworth

  I recently ran into a situation where I needed two IP addresses on the same subnet assigned to one Linux host so that we could run two SSL/TLS sites. My first approach was to use IP aliasing, e.g. using eth0:0, eth0:1, etc, but our network admins have some fairly strict settings in place for security that squashed this idea: They use DHCP snooping and normally don't allow static IP addresses. Static addressing is accomplished by using static DHCP entries, so the same MAC address always gets the same IP assignment. This feature can be disabled per switchport if you ask and you have a reason for it (thankfully I have a good relationship with the network guys and this isn't hard to do). With the DHCP snooping disabled on the switchport, they had to put in a rule on the switch that said MAC address X is allowed to have IP address Y. Unfortunately this had the side effect of also saying that MAC address X is ONLY allowed to have IP address Y. IP aliasing required that MAC address X was assigned two IP addresses, so this didn't work. There may have been a way around these issues on the switch configuration, but in an attempt to preserve good relations with the network admins I tried to find another way. Having two network interfaces seemed like the next logical step. Thankfully this Linux system is a virtual machine, so I was able to easily add a second network interface (without rebooting, I might add - pretty cool). A few keystrokes later I had two network interfaces up and running and both pulled IP addresses from DHCP. But then the problem came in: the network admins could see (on the switch) the ARP entry for both interfaces, but only the first network interface that I brought up would respond to pings or any sort of TCP or UDP traffic. After lots of digging and poking, here's what I came up with. It seems to work, but it also seems to be a lot of work for something that seems like it should be simple. Any alternate ideas out there? Step 1: Enable ARP filtering on all interfaces: # sysctl -w net.ipv4.conf.all.arp_filter=1 # echo "net.ipv4.conf.all.arp_filter = 1" >> /etc/sysctl.conf From the file networking/ip-sysctl.txt in the Linux kernel docs: arp_filter - BOOLEAN 1 - Allows you to have multiple network interfaces on the same subnet, and have the ARPs for each interface be answered based on whether or not the kernel would route a packet from the ARP'd IP out that interface (therefore you must use source based routing for this to work). In other words it allows control of which cards (usually 1) will respond to an arp request. 0 - (default) The kernel can respond to arp requests with addresses from other interfaces. This may seem wrong but it usually makes sense, because it increases the chance of successful communication. IP addresses are owned by the complete host on Linux, not by particular interfaces. Only for more complex setups like load- balancing, does this behaviour cause problems. arp_filter for the interface will be enabled if at least one of conf/{all,interface}/arp_filter is set to TRUE, it will be disabled otherwise Step 2: Implement source-based routing I basically just followed directions from http://lartc.org/howto/lartc.rpdb.multiple-links.html, although that page was written with a different goal in mind (dealing with two ISPs). Assume that the subnet is 10.0.0.0/24, the gateway is 10.0.0.1, the IP address for eth0 is 10.0.0.100, and the IP address for eth1 is 10.0.0.101. Define two new routing tables named eth0 and eth1 in /etc/iproute2/rt_tables: ... top of file omitted ... 1 eth0 2 eth1 Define the routes for these two tables: # ip route add default via 10.0.0.1 table eth0 # ip route add default via 10.0.0.1 table eth1 # ip route add 10.0.0.0/24 dev eth0 src 10.0.0.100 table eth0 # ip route add 10.0.0.0/24 dev eth1 src 10.0.0.101 table eth1 Define the rules for when to use the new routing tables: # ip rule add from 10.0.0.100 table eth0 # ip rule add from 10.0.0.101 table eth1 The main routing table was already taken care of by DHCP (and it's not even clear that its strictly necessary in this case), but it basically equates to this: # ip route add default via 10.0.0.1 dev eth0 # ip route add 130.127.48.0/23 dev eth0 src 10.0.0.100 # ip route add 130.127.48.0/23 dev eth1 src 10.0.0.101 And voila! Everything seems to work just fine. Sending pings to both IP addresses works fine. Sending pings from this system to other systems and forcing the ping to use a specific interface works fine (ping -I eth0 10.0.0.1, ping -I eth1 10.0.0.1). And most importantly, all TCP and UDP traffic to/from either IP address works as expected. So again, my question is: is there a better way to do this? This seems like a lot of work for a seemingly simple problem.

  Read the article

• mdadm raid5 recover double disk failure - with a twist (drive order)

  - by Peter Bos

  Let me acknowledge first off that I have made mistakes, and that I have a backup for most but not all of the data on this RAID. I still have hope of recovering the rest of the data. I don't have the kind of money to take the drives to a recovery expert company. Mistake #0, not having a 100% backup. I know. I have a mdadm RAID5 system of 4x3TB. Drives /dev/sd[b-e], all with one partition /dev/sd[b-e]1. I'm aware that RAID5 on very large drives is risky, yet I did it anyway. Recent events The RAID become degraded after a two drive failure. One drive [/dev/sdc] is really gone, the other [/dev/sde] came back up after a power cycle, but was not automatically re-added to the RAID. So I was left with a 4 device RAID with only 2 active drives [/dev/sdb and /dev/sdd]. Mistake #1, not using dd copies of the drives for restoring the RAID. I did not have the drives or the time. Mistake #2, not making a backup of the superblock and mdadm -E of the remaining drives. Recovery attempt I reassembled the RAID in degraded mode with mdadm --assemble --force /dev/md0, using /dev/sd[bde]1. I could then access my data. I replaced /dev/sdc with a spare; empty; identical drive. I removed the old /dev/sdc1 from the RAID mdadm --fail /dev/md0 /dev/sdc1 Mistake #3, not doing this before replacing the drive I then partitioned the new /dev/sdc and added it to the RAID. mdadm --add /dev/md0 /dev/sdc1 It then began to restore the RAID. ETA 300 mins. I followed the process via /proc/mdstat to 2% and then went to do other stuff. Checking the result Several hours (but less then 300 mins) later, I checked the process. It had stopped due to a read error on /dev/sde1. Here is where the trouble really starts I then removed /dev/sde1 from the RAID and re-added it. I can't remember why I did this; it was late. mdadm --manage /dev/md0 --remove /dev/sde1 mdadm --manage /dev/md0 --add /dev/sde1 However, /dev/sde1 was now marked as spare. So I decided to recreate the whole array using --assume-clean using what I thought was the right order, and with /dev/sdc1 missing. mdadm --create /dev/md0 --assume-clean -l5 -n4 /dev/sdb1 missing /dev/sdd1 /dev/sde1 That worked, but the filesystem was not recognized while trying to mount. (It should have been EXT4). Device order I then checked a recent backup I had of /proc/mdstat, and I found the drive order. md0 : active raid5 sdb1[0] sde1[4] sdd1[2] sdc1[1] 8790402048 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] I then remembered this RAID had suffered a drive loss about a year ago, and recovered from it by replacing the faulty drive with a spare one. That may have scrambled the device order a bit...so there was no drive [3] but only [0],[1],[2], and [4]. I tried to find the drive order with the Permute_array script: https://raid.wiki.kernel.org/index.php/Permute_array.pl but that did not find the right order. Questions I now have two main questions: I screwed up all the superblocks on the drives, but only gave: mdadm --create --assume-clean commands (so I should not have overwritten the data itself on /dev/sd[bde]1. Am I right that in theory the RAID can be restored [assuming for a moment that /dev/sde1 is ok] if I just find the right device order? Is it important that /dev/sde1 be given the device number [4] in the RAID? When I create it with mdadm --create /dev/md0 --assume-clean -l5 -n4 \ /dev/sdb1 missing /dev/sdd1 /dev/sde1 it is assigned the number [3]. I wonder if that is relevant to the calculation of the parity blocks. If it turns out to be important, how can I recreate the array with /dev/sdb1[0] missing[1] /dev/sdd1[2] /dev/sde1[4]? If I could get that to work I could start it in degraded mode and add the new drive /dev/sdc1 and let it resync again. It's OK if you would like to point out to me that this may not have been the best course of action, but you'll find that I realized this. It would be great if anyone has any suggestions.

  Read the article

• Install VLC 2.0.7 in CentOS 6.4?

  - by raaz

  I am keep failing in the installation process I have tried. I have started process as follows. yum install gcc dbus-glib-devel* lua-devel* libcddb wget http://download.videolan.org/pub/videolan/vlc/2.0.7/vlc-2.0.7.tar.xz tar -xf vlc-2.0.7.tar.xz && cd vlc-2.0.7 ./configure in the configure I am getting the error as follows configure: WARNING: No package 'libcddb' found: CDDB access disabled. checking for Linux DVB version 5... yes checking for DVBPSI... no checking gme/gme.h usability... no checking gme/gme.h presence... no checking for gme/gme.h... no checking for SID... no configure: WARNING: No package 'libsidplay2' found (required for sid). checking for OGG... no configure: WARNING: Library ogg >= 1.0 needed for ogg was not found checking for MUX_OGG... no configure: WARNING: Library ogg >= 1.0 needed for mux_ogg was not found checking for SHOUT... no configure: WARNING: Library shout >= 2.1 needed for shout was not found checking ebml/EbmlVersion.h usability... no checking ebml/EbmlVersion.h presence... no checking for ebml/EbmlVersion.h... no checking for LIBMODPLUG... no configure: WARNING: No package 'libmodplug' found No package 'libmodplug' found. checking mpc/mpcdec.h usability... no checking mpc/mpcdec.h presence... no checking for mpc/mpcdec.h... no checking mpcdec/mpcdec.h usability... no checking mpcdec/mpcdec.h presence... no checking for mpcdec/mpcdec.h... no checking for libcrystalhd/libcrystalhd_if.h... no checking mad.h usability... no checking mad.h presence... no checking for mad.h... no configure: error: Could not find libmad on your system: you may get it from http://www.underbit.com/products/mad/. Alternatively you can use --disable-mad to disable the mad plugin. [root@localhost vlc-2.0.7]# So I went to libmad http location and downloaded it and while doing make it gave me the errors.There are no errors at ./configure with libmad but make not going through. [root@localhost libmad-0.15.0b]# make (sed -e '1s|.*|/*|' -e '1b' -e '$s|.*| */|' -e '$b' \ -e 's/^.*/ *&/' ./COPYRIGHT; echo; \ echo "# ifdef __cplusplus"; \ echo 'extern "C" {'; \ echo "# endif"; echo; \ if [ ".-DFPM_INTEL" != "." ]; then \ echo ".-DFPM_INTEL" | sed -e 's|^\.-D|# define |'; echo; \ fi; \ sed -ne 's/^# *define *\(HAVE_.*_ASM\).*/# define \1/p' \ config.h; echo; \ sed -ne 's/^# *define *OPT_\(SPEED\|ACCURACY\).*/# define OPT_\1/p' \ config.h; echo; \ sed -ne 's/^# *define *\(SIZEOF_.*\)/# define \1/p' \ config.h; echo; \ for header in version.h fixed.h bit.h timer.h stream.h frame.h synth.h decoder.h; do \ echo; \ sed -n -f ./mad.h.sed ./$header; \ done; echo; \ echo "# ifdef __cplusplus"; \ echo '}'; \ echo "# endif") >mad.h make all-recursive make[1]: Entering directory `/home/raja/Downloads/libmad-0.15.0b' make[2]: Entering directory `/home/raja/Downloads/libmad-0.15.0b' if /bin/sh ./libtool --mode=compile gcc -DHAVE_CONFIG_H -I. -I. -I. -DFPM_INTEL -DASO_ZEROCHECK -Wall -march=i486 -g -O -fforce-mem -fforce-addr -fthread-jumps -fcse-follow-jumps -fcse-skip-blocks -fexpensive-optimizations -fregmove -fschedule-insns2 -fstrength-reduce -MT version.lo -MD -MP -MF ".deps/version.Tpo" \ -c -o version.lo `test -f 'version.c' || echo './'`version.c; \ then mv -f ".deps/version.Tpo" ".deps/version.Plo"; \ else rm -f ".deps/version.Tpo"; exit 1; \ fi mkdir .libs gcc -DHAVE_CONFIG_H -I. -I. -I. -DFPM_INTEL -DASO_ZEROCHECK -Wall -march=i486 -g -O -fforce-mem -fforce-addr -fthread-jumps -fcse-follow-jumps -fcse-skip-blocks -fexpensive-optimizations -fregmove -fschedule-insns2 -fstrength-reduce -MT version.lo -MD -MP -MF .deps/version.Tpo -c version.c -fPIC -DPIC -o .libs/version.lo cc1: error: unrecognized command line option "-fforce-mem" make[2]: *** [version.lo] Error 1 make[2]: Leaving directory `/home/raja/Downloads/libmad-0.15.0b' make[1]: *** [all-recursive] Error 1 make[1]: Leaving directory `/home/raja/Downloads/libmad-0.15.0b' make: *** [all] Error 2 how can i resolve the issue and install VLC in my Centos ? I am using CentOS 6.4 . Thank you.

  Read the article

• How to resolve "HTTP/1.1 403 Forbidden" errors from iCal/CalDAV server after upgrade to Snow Leopard Server?

  - by morgant

  We recently upgraded our Open Directory Master & Replica to Mac OS X 10.6.4 Snow Leopard Server. We had a mismatched server FQDN & LDAP Search Base/Kerberos Realm, so we exported all users & groups, created the new Open Directory Master w/matching FQDN & Search Base/Realm, reimported users & groups, and re-bound all servers & workstations to the new OD Master. At the same time as all of this, we upgraded our iCal/CalDAV server to Mac OS X 10.6.4 Snow Leopard Server. Ever since doing so, we've seen the following issues with our iCal/CalDAV server and iCal clients on both Mac OS X 10.5 Leopard & Mac OS X 10.6: If a user attempts to move or delete an event (single or repeating) that was created prior to the upgrade to 10.6 Server, they get the following error: Access to "blah" in "blah" in account "blah" is not permitted. The server responded: "HTTP/1.1 403 Forbidden" to operation CalDAVWriteEntityQueueableOperation. New users added to the directory get the following error when attempting to add their account to in iCal's preferences: The user "blah" has no configured pricipals. Confirm with your network administrator that your account has at least one CalDAV principal configured. Interestingly, we've since discovered that users seem to be able to delete individual events from an old repeating event without error, but that's a massive amount of work to get rid of a repeating event. I will note that we have not yet added an SRV record in DNS as instructed on page 19 of iCal_Server_Admin_v10.6.pdf. Further Investigation: In this particular case, a user is attempting to decline repeating events created prior to the upgrade to Snow Leopard Server. Granting the user full write access with sudo calendarserver_manage_principals --add-write-proxy users:user1 users:user2 (which did work) doesn't allow deletion of the events. Still get the usual error: Access to "blah blah" in "blah blah" in account "blah blah" is not permitted. The server responded: "HTTP/1.1 403 Forbidden" to operation CalDAVWriteEntityQueueableOperation. The error that shows up in /var/log/caldavd/error.log on the iCal Server when attempting to delete one of the events is: 2011-03-17 15:14:30-0400 [-] [caldav-8009] [PooledMemCacheProtocol,client] [twistedcaldav.extensions#info] PUT /calendars/__uids__/XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX/calendar/XXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX.ics HTTP/1.1 2011-03-17 15:14:30-0400 [-] [caldav-8009] [PooledMemCacheProtocol,client] [twistedcaldav.scheduling.implicit#error] Cannot change ORGANIZER: UID:XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX And the error in /var/log/system.log on the client is: Mar 17 15:14:30 192-168-21-169-dhcp iCal[33509]: CalDAV CalDAVWriteEntityQueueableOperation failed: status 'HTTP/1.1 403 Forbidden' request:\n\nBEGIN:VCALENDAR^M\nVERSION:2.0^M\nPRODID:-//Apple Inc.//iCal 3.0//EN^M\nCALSCALE:GREGORIAN^M\nBEGIN:VTIMEZONE^M\nTZID:US/Eastern^M\nBEGIN:DAYLIGHT^M\nTZOFFSETFROM:-0500^M\nTZOFFSETTO:-0400^M\nDTSTART:20070311T020000^M\nRRULE:FREQ=YEARLY;BYMONTH=3;BYDAY=2SU^M\nTZNAME:EDT^M\nEND:DAYLIGHT^M\nBEGIN:STANDARD^M\nTZOFFSETFROM:-0400^M\nTZOFFSETTO:-0500^M\nDTSTART:20071104T020000^M\nRRULE:FREQ=YEARLY;BYMONTH=11;BYDAY=1SU^M\nTZNAME:EST^M\nEND:STANDARD^M\nEND:VTIMEZONE^M\nBEGIN:VEVENT^M\nSEQUENCE:5^M\nDTSTART;TZID=US/Eastern:20090117T094500^M\nDTSTAMP:20081227T143043Z^M\nSUMMARY:blah blah^M\nATTENDEE;CN="First Last";CUTYPE=INDIVIDUAL;ROLE=REQ-PARTICIPANT:urn:uuid^M\n :XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX^M\nATTENDEE;CN="First Last";CUTYPE=INDIVIDUAL;PARTSTAT=ACCEPTED:mailto:user@d^M\n omain.tld^M\nEXDATE;TZID=US/Eastern:20110319T094500^M\nDTEND;TZID=US/Eastern:20090117T183000^M\nRRULE:FREQ=WEEKLY;INTERVAL=1^M\nTRANSP:OPAQUE^M\nUID:XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX^M\nORGANIZER;CN="First Last":mailto:[email protected]^M\nX-WR-ITIPSTATUSML:UNCLEAN^M\nCREATED:20110317T191348Z^M\nEND:VEVENT^M\nEND:VCALENDAR^M\n\n\n... response:\nHTTP/1.1 403 Forbidden^M\nDate: Thu, 17 Mar 2011 19:14:30 GMT^M\nDav: 1, access-control, calendar-access, calendar-schedule, calendar-auto-schedule, calendar-availability, inbox-availability, calendar-proxy, calendarserver-private-events, calendarserver-private-comments, calendarserver-principal-property-search^M\nContent-Type: text/xml^M\nContent-Length: 134^M\nServer: Twisted/8.2.0 TwistedWeb/8.2.0 TwistedCalDAV/2.5 (iCal Server v12.56.21)^M\n^M\n<?xml version='1.0' encoding='UTF-8'?><error xmlns='DAV:'>^M\n <valid-attendee-change xmlns='urn:ietf:params:xml:ns:caldav'/>^M\n</error> One thing I have noticed, and I'm not sure if this has any real effect is that in many of these pre-Snow Leopard Server migration events, the ORGANIZER is specified like the following: ORGANIZER;CN=First Last:mailto:[email protected] But newer ones are more like one of the two following: ORGANIZER;CN=First Last;[email protected];SCHEDULE-STATUS=1 ORGANIZER;CN=First Last;[email protected]:urn:uuid:XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX iCal_Server_Admin_v10.6.pdf notes that the ".db.sqlite" files are completely disposable, they're merely a performance cache and are re-built on the fly, so are safe to delete. I did delete the one for the organizer's calendars and it took longer to process the attempted event delete while it rebuilt the database, but still errored out in the end. FWIW the error is thrown by this code: https://trac.calendarserver.org/browser/CalendarServer/trunk/twistedcaldav/scheduling/implicit.py Any further suggestions? I see lots of questions about this in my Google searches, but not solutions and this is a widespread problem on our iCal Server. Now, we mostly try to get users to ignore them (hence the amount of time this question has been open), but every now and then I dig in deeper trying to find the culprit and/or solution.

  Read the article

• How do I add xen kernel boot parameters in grub2?

  - by Matt

  I know that I can add command line parameters to the grub2 command line by editing /etc/default/grub according to this answer How do I add a boot parameter to grub2 in Ubuntu 10.10? However, that would apply to ALL kernels would it not? How do I apply the command line parameters to specific kernels? i.e. only xen. I'm wanting to append something like: xen-pciback.hide=(06:00.0) I'm guessing I need to add it somewhere in the file: /etc/grub.d/20_linux_xen Which contains: #! /bin/sh set -e # grub-mkconfig helper script. # Copyright (C) 2006,2007,2008,2009,2010 Free Software Foundation, Inc. # # GRUB is free software: you can redistribute it and/or modify # it under the terms of the GNU General Public License as published by # the Free Software Foundation, either version 3 of the License, or # (at your option) any later version. # # GRUB is distributed in the hope that it will be useful, # but WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the # GNU General Public License for more details. # # You should have received a copy of the GNU General Public License # along with GRUB. If not, see <http://www.gnu.org/licenses/>. prefix=/usr exec_prefix=${prefix} bindir=${exec_prefix}/bin libdir=${exec_prefix}/lib . ${libdir}/grub/grub-mkconfig_lib export TEXTDOMAIN=grub export TEXTDOMAINDIR=${prefix}/share/locale CLASS="--class gnu-linux --class gnu --class os --class xen" if [ "x${GRUB_DISTRIBUTOR}" = "x" ] ; then OS=GNU/Linux else OS="${GRUB_DISTRIBUTOR} GNU/Linux" CLASS="--class $(echo ${GRUB_DISTRIBUTOR} | tr '[A-Z]' '[a-z]' | cut -d' ' -f1) ${CLASS}" fi # loop-AES arranges things so that /dev/loop/X can be our root device, but # the initrds that Linux uses don't like that. case ${GRUB_DEVICE} in /dev/loop/*|/dev/loop[0-9]) GRUB_DEVICE=`losetup ${GRUB_DEVICE} | sed -e "s/^[^(]*(\([^)]\+\)).*/\1/"` # We can't cope with devices loop-mounted from files here. case ${GRUB_DEVICE} in /dev/*) ;; *) exit 0 ;; esac ;; esac if [ "x${GRUB_DEVICE_UUID}" = "x" ] || [ "x${GRUB_DISABLE_LINUX_UUID}" = "xtrue" ] \ || ! test -e "/dev/disk/by-uuid/${GRUB_DEVICE_UUID}" \ || uses_abstraction "${GRUB_DEVICE}" lvm; then LINUX_ROOT_DEVICE=${GRUB_DEVICE} else LINUX_ROOT_DEVICE=UUID=${GRUB_DEVICE_UUID} fi linux_entry () { os="$1" version="$2" xen_version="$3" recovery="$4" args="$5" xen_args="$6" if ${recovery} ; then title="$(gettext_quoted "%s, with Xen %s and Linux %s (recovery mode)")" else title="$(gettext_quoted "%s, with Xen %s and Linux %s")" fi printf "menuentry '${title}' ${CLASS} {\n" "${os}" "${xen_version}" "${version}" if ! ${recovery} ; then save_default_entry | sed -e "s/^/\t/" fi if [ -z "${prepare_boot_cache}" ]; then prepare_boot_cache="$(prepare_grub_to_access_device ${GRUB_DEVICE_BOOT} | sed -e "s/^/\t/")" fi printf '%s\n' "${prepare_boot_cache}" xmessage="$(gettext_printf "Loading Xen %s ..." ${xen_version})" lmessage="$(gettext_printf "Loading Linux %s ..." ${version})" cat << EOF echo '$xmessage' multiboot ${rel_xen_dirname}/${xen_basename} placeholder ${xen_args} echo '$lmessage' module ${rel_dirname}/${basename} placeholder root=${linux_root_device_thisversion} ro ${args} EOF if test -n "${initrd}" ; then message="$(gettext_printf "Loading initial ramdisk ...")" cat << EOF echo '$message' module ${rel_dirname}/${initrd} EOF fi cat << EOF } EOF } linux_list=`for i in /boot/vmlinu[xz]-* /vmlinu[xz]-* ; do basename=$(basename $i) version=$(echo $basename | sed -e "s,^[^0-9]*-,,g") if grub_file_is_not_garbage "$i" && grep -qx "CONFIG_XEN_DOM0=y" /boot/config-${version} 2> /dev/null ; then echo -n "$i " ; fi done` xen_list=`for i in /boot/xen*; do if grub_file_is_not_garbage "$i" ; then echo -n "$i " ; fi done` prepare_boot_cache= while [ "x${xen_list}" != "x" ] ; do list="${linux_list}" current_xen=`version_find_latest $xen_list` xen_basename=`basename ${current_xen}` xen_dirname=`dirname ${current_xen}` rel_xen_dirname=`make_system_path_relative_to_its_root $xen_dirname` xen_version=`echo $xen_basename | sed -e "s,.gz$,,g;s,^xen-,,g"` echo "submenu \"Xen ${xen_version}\" {" while [ "x$list" != "x" ] ; do linux=`version_find_latest $list` echo "Found linux image: $linux" >&2 basename=`basename $linux` dirname=`dirname $linux` rel_dirname=`make_system_path_relative_to_its_root $dirname` version=`echo $basename | sed -e "s,^[^0-9]*-,,g"` alt_version=`echo $version | sed -e "s,\.old$,,g"` linux_root_device_thisversion="${LINUX_ROOT_DEVICE}" initrd= for i in "initrd.img-${version}" "initrd-${version}.img" \ "initrd-${version}" "initrd.img-${alt_version}" \ "initrd-${alt_version}.img" "initrd-${alt_version}"; do if test -e "${dirname}/${i}" ; then initrd="$i" break fi done if test -n "${initrd}" ; then echo "Found initrd image: ${dirname}/${initrd}" >&2 else # "UUID=" magic is parsed by initrds. Since there's no initrd, it can't work here. linux_root_device_thisversion=${GRUB_DEVICE} fi linux_entry "${OS}" "${version}" "${xen_version}" false \ "${GRUB_CMDLINE_LINUX} ${GRUB_CMDLINE_LINUX_DEFAULT}" "${GRUB_CMDLINE_XEN} ${GRUB_CMDLINE_XEN_DEFAULT}" if [ "x${GRUB_DISABLE_RECOVERY}" != "xtrue" ]; then linux_entry "${OS}" "${version}" "${xen_version}" true \ "single ${GRUB_CMDLINE_LINUX}" "${GRUB_CMDLINE_XEN}" fi list=`echo $list | tr ' ' '\n' | grep -vx $linux | tr '\n' ' '` done echo "}" xen_list=`echo $xen_list | tr ' ' '\n' | grep -vx $current_xen | tr '\n' ' '` done

  Read the article

• Linux Kernel crash mutex_lock_slowpath "blocked for more than 120 seconds". What to do?

  - by Roddick

  I have out-of-the box Debian Lenny with non-custom kernel 2.6.26-2-amd64. Brand new server that is used to 5% of it's potential, CPU and Disk-wise. Meaning it probably not crashing because of overload. every few days it freezes with hundreds of these messages in console log: : [284847.828428] INFO: task apache2:12473 blocked for more than 120 seconds. : [284847.868468] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [284847.912759] apache2 D ffff8101bc6b7ab0 0 12473 14358 : [284847.912763] ffff810160d5bc50 0000000000000082 ffff8101c0002e40 0000000000000000 : [284847.912766] ffff8101a7c42950 ffff810327d92810 ffff8101a7c42bd8 0000000400000044 : [284847.912770] ffff8101c0002e40 00000000000612d0 0000000000000000 00000040000612d0 : [284847.912773] Call Trace: : [284847.912786] [<ffffffff80429b0d>] __mutex_lock_slowpath+0x64/0x9b : [284847.912790] [<ffffffff80429972>] mutex_lock+0xa/0xb : [284847.912794] [<ffffffff802a20b9>] do_lookup+0x82/0x1c1 : [284847.912800] [<ffffffff802a4271>] __link_path_walk+0x87a/0xd19 : [284847.912805] [<ffffffff80295844>] kmem_getpages+0x96/0x15f : [284847.912808] [<ffffffff80295fb7>] ____cache_alloc_node+0x6d/0x106 : [284847.912814] [<ffffffff802a4756>] path_walk+0x46/0x8b : [284847.912819] [<ffffffff802a4a82>] do_path_lookup+0x158/0x1cf : [284847.912822] [<ffffffff802a3879>] getname+0x140/0x1a7 : [284847.912827] [<ffffffff802a53f1>] __user_walk_fd+0x37/0x4c : [284847.912831] [<ffffffff8029e381>] vfs_lstat_fd+0x18/0x47 : [284847.912840] [<ffffffff8029e3c9>] sys_newlstat+0x19/0x31 : [284847.912848] [<ffffffff8020beda>] system_call_after_swapgs+0x8a/0x8f Almost all traces has __mutex_lock_slowpath as top-level. Only some has different trace: : [284847.737386] INFO: task apache2:12472 blocked for more than 120 seconds. : [284847.777551] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [284847.824881] apache2 D ffff8101bc6b7ab0 0 12472 14358 : [284847.824886] ffff8101b9cc1c50 0000000000000086 ffffffffa0131e0a 0000000000000002 : [284847.824889] ffff8102e7454300 ffff810324c6cad0 ffff8102e7454588 0000000000000000 : [284847.824893] 0000000000000001 0000000000000296 0000000000000003 ffff8101b9cc1c58 : [284847.824896] Call Trace: : [284847.828403] [<ffffffffa0131e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 : [284847.828412] [<ffffffff80429b0d>] __mutex_lock_slowpath+0x64/0x9b : [284847.828418] [<ffffffff80429972>] mutex_lock+0xa/0xb : [284847.828421] [<ffffffff802a20b9>] do_lookup+0x82/0x1c1 : [284847.828427] [<ffffffff802a4271>] __link_path_walk+0x87a/0xd19 : [284847.828428] [<ffffffff80271296>] find_lock_page+0x1f/0x8a : [284847.828428] [<ffffffff80273182>] filemap_fault+0x1c2/0x33c : [284847.828428] [<ffffffff802a4756>] path_walk+0x46/0x8b : [284847.828428] [<ffffffff802a4a82>] do_path_lookup+0x158/0x1cf : [284847.828428] [<ffffffff802a3879>] getname+0x140/0x1a7 : [284847.828428] [<ffffffff802a53f1>] __user_walk_fd+0x37/0x4c : [284847.828428] [<ffffffff8029e381>] vfs_lstat_fd+0x18/0x47 : [284847.828428] [<ffffffff8029e3c9>] sys_newlstat+0x19/0x31 : [284847.828428] [<ffffffff8020beda>] system_call_after_swapgs+0x8a/0x8f kernel: [1912668.466347] INFO: task apache2:17984 blocked for more than 120 seconds. [1912668.507035] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [1912668.555165] apache2 D ffff8101c5637ba0 0 17984 17282 : [1912668.596752] ffff810166a7dd30 0000000000000086 0000000000000000 ffff810166a7dcd8 : [1912668.643341] ffff8101c563c880 ffff81024505f000 0000000000000002 ffff810166a7dd68 : [1912668.699566] 0000000000000086 00000000000cb1a0 0000000000000000 ffff81017f344d60 : [1912668.744773] Call Trace: : [1912668.761754] [<ffffffff8022a3ed>] pick_next_task_fair+0x6e/0x7a : [1912668.829311] [<ffffffff802be0e2>] bio_alloc_bioset+0x89/0xd9 : [1912668.861930] [<ffffffff8024ac3a>] getnstimeofday+0x39/0x98 : [1912668.897005] [<ffffffff802710f6>] sync_page+0x0/0x41 : [1912668.927868] [<ffffffff80429487>] io_schedule+0x5c/0x9e : [1912668.960286] [<ffffffff80271132>] sync_page+0x3c/0x41 : [1912668.991756] [<ffffffff804295fa>] __wait_on_bit_lock+0x36/0x66 : [1912669.031757] [<ffffffff802710e3>] __lock_page+0x5e/0x64 : [1912669.064191] [<ffffffff802461d3>] wake_bit_function+0x0/0x23 : [1912669.100100] [<ffffffff80281bc5>] handle_mm_fault+0x5e4/0x8de : [1912669.134531] [<ffffffff802461a5>] autoremove_wake_function+0x0/0x2e : [1912669.174623] [<ffffffff802aa108>] fcntl_setlk+0x1cf/0x291 : [1912669.210623] [<ffffffff802461a5>] autoremove_wake_function+0x0/0x2e : [1912669.246923] [<ffffffff802a677f>] sys_fcntl+0x280/0x2f7 After googling for "mutex_lock_slowpath" I can only find the Kernel mailing list discussions that this issue was introduced in some commit. Wthout reference to verison. Discussions as recent as Jan 25, 2011. The Kernel I am using is form Debian Lenny, year ago. What should I do? Is this bug even fixed in kernel? if it's such obvious bug why it happens so rarely? Should I download latest kernel from kernel.org and upgrade? Should I use Debian backports to install new "Approved" kernel? Am I missing something? What to do?

  Read the article

• Bridging LXC containers to host eth0 so they can have a public IP

  - by Vianney Stroebel

  UPDATE: I found the solution there: http://www.linuxfoundation.org/collaborate/workgroups/networking/bridge#No_traffic_gets_trough_.28except_ARP_and_STP.29 # cd /proc/sys/net/bridge # ls bridge-nf-call-arptables bridge-nf-call-iptables bridge-nf-call-ip6tables bridge-nf-filter-vlan-tagged # for f in bridge-nf-*; do echo 0 $f; done But I'd like to have expert opinions on this: is it safe to disable all bridge-nf-*? What are they here for? END OF UPDATE I need to bridge LXC containers to the physical interface (eth0) of my host, reading numerous tutorials, documents and blog posts on the subject. I need the containers to have their own public IP (which I've previously done KVM/libvirt). After two days of searching and trying, I still can't make it work with LXC containers. The host runs a freshly installed Ubuntu Server Quantal (12.10) with only libvirt (which I'm not using here) and lxc installed. I created the containers with : lxc-create -t ubuntu -n mycontainer So they also run Ubuntu 12.10. Content of /var/lib/lxc/mycontainer/config is: lxc.utsname = mycontainer lxc.mount = /var/lib/lxc/test/fstab lxc.rootfs = /var/lib/lxc/test/rootfs lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.veth.pair = vethmycontainer lxc.network.ipv4 = 179.43.46.233 lxc.network.hwaddr= 02:00:00:86:5b:11 lxc.devttydir = lxc lxc.tty = 4 lxc.pts = 1024 lxc.arch = amd64 lxc.cap.drop = sys_module mac_admin mac_override lxc.pivotdir = lxc_putold # uncomment the next line to run the container unconfined: #lxc.aa_profile = unconfined lxc.cgroup.devices.deny = a # Allow any mknod (but not using the node) lxc.cgroup.devices.allow = c *:* m lxc.cgroup.devices.allow = b *:* m # /dev/null and zero lxc.cgroup.devices.allow = c 1:3 rwm lxc.cgroup.devices.allow = c 1:5 rwm # consoles lxc.cgroup.devices.allow = c 5:1 rwm lxc.cgroup.devices.allow = c 5:0 rwm #lxc.cgroup.devices.allow = c 4:0 rwm #lxc.cgroup.devices.allow = c 4:1 rwm # /dev/{,u}random lxc.cgroup.devices.allow = c 1:9 rwm lxc.cgroup.devices.allow = c 1:8 rwm lxc.cgroup.devices.allow = c 136:* rwm lxc.cgroup.devices.allow = c 5:2 rwm # rtc lxc.cgroup.devices.allow = c 254:0 rwm #fuse lxc.cgroup.devices.allow = c 10:229 rwm #tun lxc.cgroup.devices.allow = c 10:200 rwm #full lxc.cgroup.devices.allow = c 1:7 rwm #hpet lxc.cgroup.devices.allow = c 10:228 rwm #kvm lxc.cgroup.devices.allow = c 10:232 rwm Then I changed my host /etc/network/interfaces to: auto lo iface lo inet loopback auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 92.281.86.226 netmask 255.255.255.0 network 92.281.86.0 broadcast 92.281.86.255 gateway 92.281.86.254 dns-nameservers 213.186.33.99 dns-search ovh.net When I try command line configuration ("brctl addif", "ifconfig eth0", etc.) my remote host becomes inaccessible and I have to hard reboot it. I changed the content of /var/lib/lxc/mycontainer/rootfs/etc/network/interfaces to: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 179.43.46.233 netmask 255.255.255.255 broadcast 178.33.40.233 gateway 92.281.86.254 It takes several minutes for mycontainer to start (lxc-start -n mycontainer). I tried replacing gateway 92.281.86.254 by : post-up route add 92.281.86.254 dev eth0 post-up route add default gw 92.281.86.254 post-down route del 92.281.86.254 dev eth0 post-down route del default gw 92.281.86.254 My container then starts instantly. But whatever configuration I set in /var/lib/lxc/mycontainer/rootfs/etc/network/interfaces, I cannot ping from mycontainer to any IP (including the host's) : ubuntu@mycontainer:~$ ping 92.281.86.226 PING 92.281.86.226 (92.281.86.226) 56(84) bytes of data. ^C --- 92.281.86.226 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 5031ms And my host cannot ping the container: root@host:~# ping 179.43.46.233 PING 179.43.46.233 (179.43.46.233) 56(84) bytes of data. ^C --- 179.43.46.233 ping statistics --- 5 packets transmitted, 0 received, 100% packet loss, time 4000ms My container's ifconfig: ubuntu@mycontainer:~$ ifconfig eth0 Link encap:Ethernet HWaddr 02:00:00:86:5b:11 inet addr:179.43.46.233 Bcast:255.255.255.255 Mask:0.0.0.0 inet6 addr: fe80::ff:fe79:5a31/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:6 overruns:0 frame:0 TX packets:54 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4070 (4.0 KB) TX bytes:4168 (4.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2496 (2.4 KB) TX bytes:2496 (2.4 KB) My host's ifconfig: root@host:~# ifconfig br0 Link encap:Ethernet HWaddr 4c:72:b9:43:65:2b inet addr:92.281.86.226 Bcast:91.121.67.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe43:652b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1453 errors:0 dropped:18 overruns:0 frame:0 TX packets:1630 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145125 (145.1 KB) TX bytes:299943 (299.9 KB) eth0 Link encap:Ethernet HWaddr 4c:72:b9:43:65:2b UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3178 errors:0 dropped:0 overruns:0 frame:0 TX packets:1637 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:298263 (298.2 KB) TX bytes:309167 (309.1 KB) Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:300 (300.0 B) TX bytes:300 (300.0 B) vethtest Link encap:Ethernet HWaddr fe:0d:7f:3e:70:88 inet6 addr: fe80::fc0d:7fff:fe3e:7088/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:54 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4168 (4.1 KB) TX bytes:4250 (4.2 KB) virbr0 Link encap:Ethernet HWaddr de:49:c5:66:cf:84 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) I have disabled lxcbr0 (USE_LXC_BRIDGE="false" in /etc/default/lxc). root@host:~# brctl show bridge name bridge id STP enabled interfaces br0 8000.4c72b943652b no eth0 vethtest I have configured the IP 179.43.46.233 to point to 02:00:00:86:5b:11 in my hosting provider (OVH) config panel. (The IPs in this post are not the real ones.) Thanks for reading this long question! :-) Vianney

  Read the article

• DDNS Not Creating Journal (Dhcpd and Named)

  - by user130094

  * EDIT 1 * After monkeying with additional debug logging I see some log entries of interest. 27-Jul-2012 23:45:26.537 general: error: zone example.lan/IN/internal: journal rollforward failed: no more 27-Jul-2012 23:45:26.537 general: error: zone example.lan/IN/internal: not loaded due to errors. ^^^ If I can remedy the above messages I think I'll be good to go ^^^ * EDIT 2 * Grasping at straws I touched a forward and a reverse zone journal file and restarted named. Boom! Works. Despite documentation stating the files are created automatically and what I have seen before... dunno why but that did the trick. Also re-checked perms on the dir the files live in. As certain as I was, they were correct with named having rw. CentOS 6 (final) dhcpd 4.1.1-P1 named BIND 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6 Basic DHCP and DNS functionality are in place on 192.168.111.2. Clients are assigned addresses as intended and can resolve local DNS names as well as Internet names. My problem is that named's zone journal files are not created. chroot: /var/named/chroot I tried placing the zone files in various directories (/var/named/data, /var/named, /var/named/dynamic - no matter which dir with named owning and wide open perms I now get nowhere). Along the way I, at one point, got a permission denied when named tried to create the journal. Resolved the issue by: chown --recursive named:named /var/named chmod --recursive 777 /var/named The journal was then created and here's where things fell apart. I attempted to tame permissions to something more sane and broke it. Once changed and having restarted named it threw an error indicating the journal was out of sync (or something to that affect)... didn't matter since this is a new setup so I deleted it and now it is not recreated. Now though I see no errors in /var/log/messages, my chrooted /var/log/named.log, or chrooted /var/log/named.debug. I increased the debug level with 'rndc trace' - no love. Increased trace to 10, still nothing. SELinux is disabled... [root@server temp]# sestatus SELinux status: disabled dhcpd.conf... allow client-updates; ddns-update-style interim; subnet 192.168.111.0 netmask 255.255.255.224 { ... key dhcpudpate { algorithm hmac-md5; secret LDJMdPdEZED+/nN/AGO9ZA==; } zone example.lan. { primary 192.168.111.2; key dhcpudpate; } } named.conf... key dhcpudpate { algorithm hmac-md5; secret "LDJMdPdEZED+/nN/AGO9ZA=="; }; zone "example.lan" { type master; file "/var/named/dynamic/example.lan.db"; allow-transfer { none; }; allow-update { key dhcpudpate; }; notify false; check-names ignore; }; The following shows /var/log/named.log output of named starting up - no errors. 27-Jul-2012 21:33:39.349 general: info: zone 111.168.192.in-addr.arpa/IN/internal: loaded serial 2012072601 27-Jul-2012 21:33:39.349 general: info: zone example.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.350 general: info: zone example2.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.350 general: info: zone example3.lan/IN/internal: loaded serial 2012072601 27-Jul-2012 21:33:39.350 general: info: zone example4.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.351 general: info: zone example5.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.351 general: info: managed-keys-zone ./IN/internal: loaded serial 0 27-Jul-2012 21:33:39.351 general: info: zone example.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example1.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example2.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example3.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.353 general: info: managed-keys-zone ./IN/external: loaded serial 0 27-Jul-2012 21:33:39.353 general: notice: running 27-Jul-2012 21:34:03.825 general: info: received control channel command 'trace 10' 27-Jul-2012 21:34:03.825 general: info: debug level is now 10 ...and /var/log/messages for a named start... Jul 27 23:02:04 server named[9124]: ---------------------------------------------------- Jul 27 23:02:04 server named[9124]: BIND 9 is maintained by Internet Systems Consortium, Jul 27 23:02:04 server named[9124]: Inc. (ISC), a non-profit 501(c)(3) public-benefit Jul 27 23:02:04 server named[9124]: corporation. Support and training for BIND 9 are Jul 27 23:02:04 server named[9124]: available at https://www.isc.org/support Jul 27 23:02:04 server named[9124]: ---------------------------------------------------- Jul 27 23:02:04 server named[9124]: adjusted limit on open files from 4096 to 1048576 Jul 27 23:02:04 server named[9124]: found 2 CPUs, using 2 worker threads Jul 27 23:02:04 server named[9124]: using up to 4096 sockets Jul 27 23:02:04 server named[9124]: loading configuration from '/etc/named.conf' Jul 27 23:02:04 server named[9124]: using default UDP/IPv4 port range: [1024, 65535] Jul 27 23:02:04 server named[9124]: using default UDP/IPv6 port range: [1024, 65535] Jul 27 23:02:04 server named[9124]: listening on IPv4 interface eth0, 192.168.111.2#53 Jul 27 23:02:04 server named[9124]: generating session key for dynamic DNS Jul 27 23:02:04 server named[9124]: sizing zone task pool based on 12 zones Jul 27 23:02:04 server named[9124]: set up managed keys zone for view internal, file 'dynamic/3bed2cb3a3acf7b6a8ef408420cc682d5520e26976d354254f528c965612054f.mkeys' Jul 27 23:02:04 server named[9124]: set up managed keys zone for view external, file 'dynamic/3c4623849a49a53911c4a3e48d8cead8a1858960bccdea7a1b978d73ec2f06d7.mkeys' Jul 27 23:02:04 server named[9124]: command channel listening on 127.0.0.1#953 What can I do to troubleshoot this further? It almost seems as though dhcpd is not triggering the update. Maybe I should troubleshoot here and, if so, how? Many thanks.

  Read the article

• How does this main domain have a CNAME record?

  - by TRiG

  I was under the impression that only subdomains could have CNAME records: main domains need to define all their own records. However, apt-get.com seems to have only a CNAME record. How can this work? $ dig apt-get.com ; <<>> DiG 9.8.1-P1 <<>> apt-get.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 45743 ;; flags: qr rd ra; QUERY: 1, ANSWER: 9, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;apt-get.com. IN A ;; ANSWER SECTION: apt-get.com. 86336 IN CNAME thie5ku9.dsgeneration.com. thie5ku9.dsgeneration.com. 60 IN A 208.73.211.242 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.246 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.166 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.232 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.161 thie5ku9.dsgeneration.com. 60 IN A 208.73.210.233 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.186 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.188 ;; Query time: 59 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Tue Jun 10 15:05:48 2014 ;; MSG SIZE rcvd: 193 $ dig apt-get.com ns ; <<>> DiG 9.8.1-P1 <<>> apt-get.com ns ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 43831 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;apt-get.com. IN NS ;; Query time: 26 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Tue Jun 10 15:12:37 2014 ;; MSG SIZE rcvd: 29 $ dig apt-get.com ns @b.gtld-servers.net ; <<>> DiG 9.8.1-P1 <<>> apt-get.com ns @b.gtld-servers.net ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 38228 ;; flags: qr rd; QUERY: 1, ANSWER: 0, AUTHORITY: 2, ADDITIONAL: 2 ;; WARNING: recursion requested but not available ;; QUESTION SECTION: ;apt-get.com. IN NS ;; AUTHORITY SECTION: apt-get.com. 172800 IN NS ns1.domainrecover.com. apt-get.com. 172800 IN NS ns2.domainrecover.com. ;; ADDITIONAL SECTION: ns1.domainrecover.com. 172800 IN A 66.45.232.66 ns2.domainrecover.com. 172800 IN A 65.23.159.179 ;; Query time: 70 msec ;; SERVER: 192.33.14.30#53(192.33.14.30) ;; WHEN: Tue Jun 10 15:07:05 2014 ;; MSG SIZE rcvd: 111 The domain does resolve. I get the following headers: GET / HTTP/1.1 User-Agent: Testing_Sniffer/4.15 Host: apt-get.com Accept: */* HTTP/1.0 200 (OK) Cache-Control: private, no-cache, must-revalidate Connection: Keep-Alive Pragma: no-cache Server: Oversee Turing v1.0.0 Content-Length: 1347 Content-Type: text/html Expires: Mon, 26 Jul 1997 05:00:00 GMT Keep-Alive: timeout=3, max=96 P3P: policyref="http://www.dsparking.com/w3c/p3p.xml", CP="NOI DSP COR ADMa OUR NOR STA" Set-Cookie: parkinglot=1; domain=.apt-get.com; path=/; expires=Wed, 11-Jun-2014 14:10:37 GMT <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Frameset//EN" "http://www.w3.org/TR/html4/frameset.dtd"> <!-- turing_cluster_prod --> <html> <head> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <title>apt-get.com</title> <meta name="keywords" content="apt-get.com" /> <meta name="description" content="apt-get.com" /> <meta name="robots" content="index, follow" /> <meta name="revisit-after" content="10" /> <meta name="viewport" content="width=device-width, initial-scale=1.0" /> <script type="text/javascript"> document.cookie = "jsc=1"; </script> </head> <frameset rows="100%,*" frameborder="no" border="0" framespacing="0"> <frame src="http://apt-get.com?epl=5PfLSSqWrYDAt-gbwMDK_rA3b1UJCYVTJHfxTzr9FTDQV84b6vAgVhU3FTeCRQNiuRNv79Ni0V3mkEVNRhpqo2gpMjp5iOIR1w2_EISPENaqzoXohVXl2QI3ryXlRCB4FaIIaxynnWXWY6QBgBgNiIZ6agD1NBoNGg0ajXpUCXUAIJDer78AAOB_AwAAQIDbCwAAe_NWlVlTJllBMTZoWkKPAAAA8A" name="apt-get.com"> </frameset> <noframes> <body><a href="http://apt-get.com?epl=5PfLSSqWrYDAt-gbwMDK_rA3b1UJCYVTJHfxTzr9FTDQV84b6vAgVhU3FTeCRQNiuRNv79Ni0V3mkEVNRhpqo2gpMjp5iOIR1w2_EISPENaqzoXohVXl2QI3ryXlRCB4FaIIaxynnWXWY6QBgBgNiIZ6agD1NBoNGg0ajXpUCXUAIJDer78AAOB_AwAAQIDbCwAAe_NWlVlTJllBMTZoWkKPAAAA8A">Click here to go to apt-get.com</a>.</body> </noframes> </html>

  Read the article

• firefox, opera 'The connection was reset' on few POST method calls on Windows and Ubuntu

  - by Gopalakrishnan Subramani

  my website works well with GET method, also few POST methods. Some pages with POST method doesn't work. Some pages with POST work. For example, login page uses POST that works fine. When I post the data on webpage, firefox says "Connecting..." and finally report connection timed out error. The same behavior happens with Opera as well. However Google Chrome works fine. At the server side, I use nginx 1.2.4 with HTTPS and uwsgi for python (flask framework) app. I use geotrust certificate. The same behavior happens with Windows 7 and Ubuntu 12.04 on firefox. I tried firefox in safemode, but no luck. Set auto-detect proxy settings. no luck. Cleared all cookies. no luck Anyone help me to fix this issue? I am posting ngix config. shame on me. I use root, I know which is not advised. need to fix soon. user root; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; ## # Gzip Settings ## gzip on; gzip_disable "msie6"; # gzip_vary on; # gzip_proxied any; # gzip_comp_level 6; # gzip_buffers 16 8k; # gzip_http_version 1.1; # gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; ## # nginx-naxsi config ## # Uncomment it if you installed nginx-naxsi ## #include /etc/nginx/naxsi_core.rules; ## # nginx-passenger config ## # Uncomment it if you installed nginx-passenger ## #passenger_root /usr; #passenger_ruby /usr/bin/ruby; ## # Virtual Host Configs ## include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; ssl_session_cache shared:SSL:10m; ssl_session_timeout 10m; server { listen 80; server_name www.example.com; rewrite ^(.*) https://example.com$1 permanent; } server { listen 80; server_name example.com; rewrite ^ https://$server_name$request_uri? permanent; } server { listen 443; server_name example.com; keepalive_timeout 70; ssl on; ssl_certificate /root/cc.cert; ssl_certificate_key /root/cc.key; ssl_protocols SSLv3 TLSv1 TLSv1.1 TLSv1.2; #ssl_ciphers HIGH:!aNULL:!MD5; ssl_ciphers RC4:HIGH:!aNULL:!MD5; ssl_prefer_server_ciphers on; location / { try_files $uri @app; } location @app { include uwsgi_params; uwsgi_pass unix:/tmp/uwsgi.sock; } } } #mail { # # See sample authentication script at: # # http://wiki.nginx.org/ImapAuthenticateWithApachePhpScript # # # auth_http localhost/auth.php; # # pop3_capabilities "TOP" "USER"; # # imap_capabilities "IMAP4rev1" "UIDPLUS"; # # server { # listen localhost:110; # protocol pop3; # proxy on; # } # # server { # listen localhost:143; # protocol imap; # proxy on; # } #}

  Read the article

• dual boot install--no GRUB

  - by Jim Syyap

  My computer recently had a hardware upgrade and now runs on Windows 7. I decided to install Ubuntu 11.04 as dual boot using the ISO I got from ubuntu.com downloaded onto my USB stick. Restarting with the USB stick, I was able to install Ubuntu 11.04 choosing the option: Install Ubuntu 11.04 side by side with Windows 7 (or something like that). No errors were encountered on installation. However on restarting, there was no GRUB; the system went straight into Windows 7. Looking for answers, I found these: http://essayboard.com/2011/07/12/how-to-dual-boot-ubuntu-11-04-and-windows-7-the-traditional-way-through-grub-2/ http://ubuntuforums.org/showthread.php?t=1774523 Following their instructions, I got: Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== => Windows is installed in the MBR of /dev/sda. => Syslinux MBR (3.61-4.03) is installed in the MBR of /dev/sdb. => Grub2 (v1.99) is installed in the MBR of /dev/sdc and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos7)/boot/grub on this drive. sda1: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /grldr /bootmgr /Boot/BCD /grldr sda2: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /Windows/System32/winload.exe sdb1: __________________________________________________ ________________________ File system: vfat Boot sector type: SYSLINUX 4.02 debian-20101016 ...........>...r>....... ......0...~.k...~...f...M.f.f....f..8~....>2} Boot sector info: Syslinux looks at sector 1437504 of /dev/sdb1 for its second stage. SYSLINUX is installed in the directory. The integrity check of the ADV area failed. According to the info in the boot sector, sdb1 starts at sector 0. But according to the info from fdisk, sdb1 starts at sector 62. Operating System: Boot files: /boot/grub/grub.cfg /syslinux/syslinux.cfg /ldlinux.sys sdc1: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows XP Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sdc2: __________________________________________________ ________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdc5: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: sdc6: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: sdc7: __________________________________________________ ________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 11.04 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdc8: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: Going back into Ubuntu and running sudo fdisk -l , I got these: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002f393 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 19458 156185600 7 HPFS/NTFS Disk /dev/sdb: 2011 MB, 2011168768 bytes 62 heads, 62 sectors/track, 1021 cylinders Units = cylinders of 3844 * 512 = 1968128 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000f2ab9 Device Boot Start End Blocks Id System /dev/sdb1 * 1 1021 1962331 c W95 FAT32 (LBA) Disk /dev/sdc: 1000.2 GB, 1000202043392 bytes 255 heads, 63 sectors/track, 121600 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00261ddd Device Boot Start End Blocks Id System /dev/sdc1 * 1 60657 487222656+ 7 HPFS/NTFS /dev/sdc2 60657 121600 489527681 5 Extended /dev/sdc5 120563 121600 8337703+ 82 Linux swap / Solaris /dev/sdc6 120073 120562 3930112 82 Linux swap / Solaris /dev/sdc7 60657 119584 473328640 83 Linux /dev/sdc8 119584 120072 3923968 82 Linux swap / Solaris Should I proceed and do the following? Assuming Ubuntu 11.04 was installed on device sdb1, do this: sudo mount /dev/sdb1 /mnt Then do this: sudo grub-install--root-directory=/mnt /dev/sdb Notice there are two dashes in front of the root directory, and I'm not using sdb1 but sdb. Since the command in step 15 had reinstalled Grub 2, now we need to unmount the /mnt (i.e. sdb1) to clean up. Do this: sudo umount /mnt Reboot and remove Ubuntu 11.04 CD/DVD from disk tray. Log into Ubuntu 11.04 (you have no choice but it will make you log into Ubuntu 11.04 at this point). Open up a terminal in Ubuntu 11.04 (using real installation, not live CD/DVD). Execute this command: sudo update-grub Reboot the machine.

  Read the article

• Screen Casting using ffmpeg (too fast)

  - by rowman

  I can use ffmpeg to make screen casts: ffmpeg -f x11grab -s 1280x800 -i :0.0 -c:v libx264 -framerate 30 -r 30 -crf 18 out.mkv However the output comes out to be too fast paced. It also happens with GTK RecordMyDesktop if I enable the encode on the fly. So, the questions is how to get a normal video pace. Also in order to capture the sound with ffmpeg what option should be used? FFmpeg Output: ffmpeg -f x11grab -s 1280x800 -r 30 -i :0.0 -c:v libx264 -framerate 30 -r 30 -crf 18 out.mkv ffmpeg version N-35162-g87244c8 Copyright (c) 2000-2012 the FFmpeg developers built on Oct 7 2012 15:56:19 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 51. 73.102 / 51. 73.102 libavcodec 54. 64.100 / 54. 64.100 libavformat 54. 29.105 / 54. 29.105 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 19.102 / 3. 19.102 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 16.100 / 0. 16.100 libpostproc 52. 1.100 / 52. 1.100 [x11grab @ 0xab896a0] device: :0.0 -> display: :0.0 x: 0 y: 0 width: 1280 height: 800 [x11grab @ 0xab896a0] shared memory extension found [x11grab @ 0xab896a0] Estimating duration from bitrate, this may be inaccurate Input #0, x11grab, from ':0.0': Duration: N/A, start: 1350136942.608988, bitrate: 983040 kb/s Stream #0:0: Video: rawvideo (BGR[0] / 0x524742), bgr0, 1280x800, 983040 kb/s, 30 tbr, 1000k tbn, 30 tbc [libx264 @ 0xab87320] using cpu capabilities: MMX2 SSE2Fast SSSE3 Cache64 SlowCTZ SlowAtom [libx264 @ 0xab87320] profile High 4:4:4 Predictive, level 3.2, 4:4:4 8-bit [libx264 @ 0xab87320] 264 - core 128 r2 198a7ea - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=4 threads=6 lookahead_threads=1 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=18.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, matroska, to 'out.mkv': Metadata: encoder : Lavf54.29.105 Stream #0:0: Video: h264, yuv444p, 1280x800, q=-1--1, 1k tbn, 30 tbc Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> libx264) Press [q] to stop, [?] for help frame= 10 fps=0.0 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 19 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 28 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 37 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 45 fps= 16 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 47 fps= 14 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 52 fps= 13 q=24.0 size= 257kB time=00:00:00.00 bitrate=2101632.0kbiframe= 55 fps= 12 q=24.0 size= 257kB time=00:00:00.10 bitrate=20808.2kbitsframe= 59 fps= 11 q=24.0 size= 289kB time=00:00:00.23 bitrate=10145.0kbitsframe= 64 fps= 11 q=24.0 size= 289kB time=00:00:00.40 bitrate=5894.7kbits/frame= 70 fps= 11 q=24.0 size= 289kB time=00:00:00.60 bitrate=3933.1kbits/frame= 72 fps= 10 q=24.0 size= 289kB time=00:00:00.66 bitrate=3549.2kbits/frame= 77 fps=9.8 q=24.0 size= 289kB time=00:00:00.83 bitrate=2837.7kbits/frame= 80 fps=9.6 q=24.0 size= 289kB time=00:00:00.93 bitrate=2533.5kbits/frame= 85 fps=9.3 q=24.0 size= 289kB time=00:00:01.10 bitrate=2146.9kbits/frame= 89 fps=9.3 q=24.0 size= 289kB time=00:00:01.23 bitrate=1917.1kbits/frame= 92 fps=9.1 q=24.0 size= 289kB time=00:00:01.33 bitrate=1773.3kbits/frame= 96 fps=9.0 q=24.0 size= 289kB time=00:00:01.46 bitrate=1612.4kbits/frame= 99 fps=8.8 q=24.0 size= 321kB time=00:00:01.56 bitrate=1676.8kbits/frame= 104 fps=8.7 q=24.0 size= 321kB time=00:00:01.73 bitrate=1515.2kbits/frame= 109 fps=5.3 q=24.0 Lsize= 1093kB time=00:00:03.56 bitrate=2511.5kbits/s video:1092kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.120198% [libx264 @ 0xab87320] frame I:3 Avg QP:18.93 size:142610 [libx264 @ 0xab87320] frame P:43 Avg QP:20.79 size: 15751 [libx264 @ 0xab87320] frame B:63 Avg QP:23.75 size: 195 [libx264 @ 0xab87320] consecutive B-frames: 21.1% 1.8% 11.0% 66.1% [libx264 @ 0xab87320] mb I I16..4: 50.0% 21.1% 28.9% [libx264 @ 0xab87320] mb P I16..4: 6.1% 0.9% 3.2% P16..4: 5.5% 1.2% 0.6% 0.0% 0.0% skip:82.5% [libx264 @ 0xab87320] mb B I16..4: 0.4% 0.1% 0.0% B16..8: 2.9% 0.1% 0.0% direct: 0.0% skip:96.5% L0:40.7% L1:57.0% BI: 2.3% [libx264 @ 0xab87320] 8x8 transform intra:14.5% inter:46.1% [libx264 @ 0xab87320] coded y,u,v intra: 33.5% 24.1% 25.4% inter: 0.9% 0.4% 0.4% [libx264 @ 0xab87320] i16 v,h,dc,p: 70% 26% 1% 3% [libx264 @ 0xab87320] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 11% 21% 30% 5% 7% 5% 7% 4% 10% [libx264 @ 0xab87320] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 32% 35% 12% 2% 4% 3% 4% 3% 5% [libx264 @ 0xab87320] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0xab87320] ref P L0: 57.0% 5.6% 26.8% 10.6% [libx264 @ 0xab87320] ref B L0: 69.4% 22.6% 8.0% [libx264 @ 0xab87320] ref B L1: 93.7% 6.3% [libx264 @ 0xab87320] kb/s:2460.40

  Read the article

• IPV6 causing issue with DNS

  - by Mike Wells

  I have set up an 'internal' DNS at my work, basically we have ourdomain.com that is for internet, email etc and I have created on one of our linux network servers (debian) a DNS using bind9 with the domain ourdomain.inc. So based on my files below and the symptoms I'm describing; what effect could IPV6 be having on my setup? What can I do to fix this? I assume it is not actually the IPV6 causing the issue, but rather something in my setup. These are the critical (I think) files I have modified: named.conf.local zone "ourdomain.inc" { type master; file "/etc/bind/zones/ourdomain.inc.db"; }; zone "201.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.201.168.192.in-addr.arpa"; }; named.conf.options options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. forwarders { 1.2.3.4; //IP of our external DNS provider }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; ourdomain.inc.db $TTL 86400 ourdomain.inc. IN SOA ns1.ipower.com. admin.ourdomain.inc. ( 2006081401 28800 3600 604800 38400 ) serv1 IN A 192.168.201.223 serv2 IN A 192.168.201.220 serv3 IN A 192.168.201.219 ns1.ipower.com. IN A 1.2.3.4 ns2.ipower.com. IN A 1.2.3.5 @ IN NS ns1.ipower.com. @ IN NS ns2.ipower.com. svn IN CNAME serv1 docs IN CNAME serv2 jira IN CNAME serv3 confluence IN CNAME serv3 fisheye IN CNAME serv3 rev.201.168.192.in-addr.arpa $TTL 86400 201.168.192.in-addr.arpa. IN SOA ns1.ipower.com. admin.ourdomain.inc. ( 2006081401; 28800; 604800; 604800; 86400 ) 223 IN PTR serv1 @ IN NS ns1.ipower.com. @ IN NS ns2.ipower.com. named.conf include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; I then made our internal DNS my preferred DNS with the two external DNSs the next in-line. More the most part this seems to work, I can ping svn.ourdomain.inc and it resolves to the correct IP, I can also ping google.com and it also resolves no problem. So all seem good. However, periodically (couple of times a day at least), I loose the ability to ping the svn.domain.inc (and all others defined under the internal DNS). What seem to fix the issue temporarily is to disable IPV6 on the network adapter of the client machine and then re-enable it. Then it works for a bit but will always fail again. System Info Internal DNS Distributor ID: Debian Description: Debian GNU/Linux 6.0.6 (squeeze) Release: 6.0.6 Codename: squeeze Linux 2.6.32-5-686 i686 BIND 9.7.3 PC OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7601 Service Pack 1 Build 7601 System Type: x64-based PC Network Card(s): 2 NIC(s) Installed. [01]: Realtek PCIe GBE Family Controller Connection Name: WORK LAN DHCP Enabled: No IP address(es) [01]: the.ipv4.address [02]: the:ipv6:address The question... So based on my files above and the symptoms I described; what effect could IPV6 be having on my setup? What can I do to fix this? I assume it is not actually the IPV6 causing the issue, but rather something in my setup.

  Read the article

• e2fsck extremly slow, although enough memory exists

  - by kaefert

  I've got this external USB-Disk: kaefert@blechmobil:~$ lsusb -s 2:3 Bus 002 Device 003: ID 0bc2:3320 Seagate RSS LLC As can be seen in this dmesg output, there are some problems that prevents that disk from beeing mounted: kaefert@blechmobil:~$ dmesg | grep sdb [ 114.474342] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.475089] sd 5:0:0:0: [sdb] Write Protect is off [ 114.475092] sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 114.475959] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.477093] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.501649] sdb: sdb1 [ 114.502717] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.504354] sd 5:0:0:0: [sdb] Attached SCSI disk [ 116.804408] EXT4-fs (sdb1): ext4_check_descriptors: Checksum for group 3976 failed (47397!=61519) [ 116.804413] EXT4-fs (sdb1): group descriptors corrupted! So I went and fired up my favorite partition manager - gparted, and told it to verify and repair the partition sdb1. This made gparted call e2fsck (version 1.42.4 (12-Jun-2012)) e2fsck -f -y -v /dev/sdb1 Although gparted called e2fsck with the "-v" option, sadly it doesn't show me the output of my e2fsck process (bugreport https://bugzilla.gnome.org/show_bug.cgi?id=467925 ) I started this whole thing on Sunday (2012-11-04_2200) evening, so about 48 hours ago, this is what htop says about it now (2012-11-06-1900): PID USER PRI NI VIRT RES SHR S CPU% MEM% TIME+ Command 3704 root 39 19 1560M 1166M 768 R 98.0 19.5 42h56:43 e2fsck -f -y -v /dev/sdb1 Now I found a few posts on the internet that discuss e2fsck running slow, for example: http://gparted-forum.surf4.info/viewtopic.php?id=13613 where they write that its a good idea to see if the disk is just that slow because maybe its damaged, and I think these outputs tell me that this is not the case in my case: kaefert@blechmobil:~$ sudo hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 3562 MB in 2.00 seconds = 1783.29 MB/sec Timing buffered disk reads: 82 MB in 3.01 seconds = 27.26 MB/sec kaefert@blechmobil:~$ sudo hdparm /dev/sdb /dev/sdb: multcount = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 364801/255/63, sectors = 5860533160, start = 0 However, although I can read quickly from that disk, this disk speed doesn't seem to be used by e2fsck, considering tools like gkrellm or iotop or this: kaefert@blechmobil:~$ iostat -x Linux 3.2.0-2-amd64 (blechmobil) 2012-11-06 _x86_64_ (2 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 14,24 47,81 14,63 0,95 0,00 22,37 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util sda 0,59 8,29 2,42 5,14 43,17 160,17 53,75 0,30 39,80 8,72 54,42 3,95 2,99 sdb 137,54 5,48 9,23 0,20 587,07 22,73 129,35 0,07 7,70 7,51 16,18 2,17 2,04 Now I researched a little bit on how to find out what e2fsck is doing with all that processor time, and I found the tool strace, which gives me this: kaefert@blechmobil:~$ sudo strace -p3704 lseek(4, 41026998272, SEEK_SET) = 41026998272 write(4, "\212\354K[_\361\3nl\212\245\352\255jR\303\354\312Yv\334p\253r\217\265\3567\325\257\3766"..., 4096) = 4096 lseek(4, 48404766720, SEEK_SET) = 48404766720 read(4, "\7t\260\366\346\337\304\210\33\267j\35\377'\31f\372\252\ffU\317.y\211\360\36\240c\30`\34"..., 4096) = 4096 lseek(4, 41027002368, SEEK_SET) = 41027002368 write(4, "\232]7Ws\321\352\t\1@[+5\263\334\276{\343zZx\352\21\316`1\271[\202\350R`"..., 4096) = 4096 lseek(4, 48404770816, SEEK_SET) = 48404770816 read(4, "\17\362r\230\327\25\346//\210H\v\311\3237\323K\304\306\361a\223\311\324\272?\213\tq \370\24"..., 4096) = 4096 lseek(4, 41027006464, SEEK_SET) = 41027006464 write(4, "\367yy>x\216?=\324Z\305\351\376&\25\244\210\271\22\306}\276\237\370(\214\205G\262\360\257#"..., 4096) = 4096 lseek(4, 48404774912, SEEK_SET) = 48404774912 read(4, "\365\25\0\21|T\0\21}3t_\272\373\222k\r\177\303\1\201\261\221$\261B\232\3142\21U\316"..., 4096) = 4096 ^CProcess 3704 detached around 16 of these lines every second, so 4 read and 4 write operations every second, which I don't consider to be a lot.. And finally, my question: Will this process ever finish? If those numbers from fseek (48404774912) represent bytes, that would be something like 45 gigabytes, with this beeing a 3 terrabyte disk, which would give me 134 days to go, if the speed stays constant, and he scans the disk like this completly and only once. Do you have some advice for me? I have most of the data on that disk elsewhere, but I've put a lot of hours into sorting and merging it to this disk, so I would prefer to getting this disk up and running again, without formatting it anew. I don't think that the hardware is damaged since the disk is only a few months and since I can't see any I/O errors in the dmesg output. UPDATE: I just looked at the strace output again (2012-11-06_2300), now it looks like this: lseek(4, 1419860611072, SEEK_SET) = 1419860611072 read(4, "3#\f\2447\335\0\22A\355\374\276j\204'\207|\217V|\23\245[\7VP\251\242\276\207\317:"..., 4096) = 4096 lseek(4, 43018145792, SEEK_SET) = 43018145792 write(4, "]\206\231\342Y\204-2I\362\242\344\6R\205\361\324\177\265\317C\334V\324\260\334\275t=\10F."..., 4096) = 4096 lseek(4, 1419860615168, SEEK_SET) = 1419860615168 read(4, "\262\305\314Y\367\37x\326\245\226\226\320N\333$s\34\204\311\222\7\315\236\336\300TK\337\264\236\211n"..., 4096) = 4096 lseek(4, 43018149888, SEEK_SET) = 43018149888 write(4, "\271\224m\311\224\25!I\376\16;\377\0\223H\25Yd\201Y\342\r\203\271\24eG<\202{\373V"..., 4096) = 4096 lseek(4, 1419860619264, SEEK_SET) = 1419860619264 read(4, ";d\360\177\n\346\253\210\222|\250\352T\335M\33\260\320\261\7g\222P\344H?t\240\20\2548\310"..., 4096) = 4096 lseek(4, 43018153984, SEEK_SET) = 43018153984 write(4, "\360\252j\317\310\251G\227\335{\214`\341\267\31Y\202\360\v\374\307oq\3063\217Z\223\313\36D\211"..., 4096) = 4096 So this number of the lseeks before the reads, like 1419860619264 are already a lot bigger, standing for 1.29 terabytes if the numbers are bytes, so it doesn't seem to be a linear progress on a big scale, maybe there are only some areas that need work, that have big gaps in between them. (times are in CET)

  Read the article

< Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >