Search Results

Search found 49860 results on 1995 pages for 'reference type'.

Page 453/1995 | < Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >

• Cannot browse remote networks even with WINS configured

  - by paradroid

  As the NetBIOS protocol acts on Layer 2 and so is not routable, In order to enable network browsing of remote networks, WINS has been installed and configured on two domain controllers, both of which are on different networks. The WINS servers seem to be replicating with eachother, and each has 127.0.0.1 set as the Primary WINS Server in each of their LAN interface properties, with nothing entered for Secondary WINS Server. The DC which holds the PDC Emulator FSMO role has the Computer Browser service running and set to Auto start, and it has the WINS/NBT node type network setting at 0x8 (H-node - Hybrid node). Remote network browsing does not work. Is the WINS/NBT node type correct for this scenario? The reason why I think it may not be the right one is because I set the DHCP Server's 046 WINS/NBT node type option to 0x8 as well, after which the DHCP clients started to disappear from the Network folders. When that option is not set, does it default to B-node (Broadcast node)? Or could it be a problem with the WINS servers setup?

  Read the article

• Cannot find network path for computer in workgroup of home Windows XP PCs

  - by John Galt

  VMWare Workstation 6.5 is running as an app on a Windows Vista 64bit PC host. Thanks to Workstation we have 2 guest machines running: TerriVM and MattVM (both of these run Windows XP SP2). We are attempting to get virtual networking configured so we can access the files of both of these VM guest systems from other real PCs connected to this home network. We think we are close but we can't quite get it right... Here is what we've done so far: * On VM Workstation, we set "Host Virtual Network Mapping" to use VMnet0 with the setting "Bridge to an automatically chosen adapter". * On each VM guest (i.e. using Windows explorer on XP), we rightmouse on the C disk, click "Sharing" tab, set shareName to "C_Disk" and check both boxes labeled "Share this folder on the network" and "Allow network users to change my files". Symptoms: On "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \TerriVM\C_Disk and assign drive letter T. We see all the folders on this shared drive and can open files on them. So that is good. On same "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \MattVM\C_Disk and assign drive letter M. We get a message box "_The network path \mattvm\C_Disk could not be found_". Alternatively, we type just \mattvm\ into the Folder box and click "Browse" and get a dialog box where we drill down from "Entire Network" to "Microsoft Windows Network" to "Workgroup" where both TerriVM and MattVM are listed as computers on the network. Clicking the + sign next to MattVM gives an hourglass and never enables the OK button and I have to cancel. In summary, I think we've attempted to share both of these virtual machines using the same techniques and connect to them in similar fashion, but one connects properly and the other machine can be seen but no shared resources on it can be accessed. Can anyone suggest something possibly overlooked or something to try? Thanks so much in advance.

  Read the article

• nginx and proxy_hide_header

  - by giskard

  When I curl for a URL I get this answer back: > < HTTP/1.1 200 OK < Server: nginx/0.7.65 < Date: Thu, 04 Mar 2010 12:18:27 GMT < Content-Type: application/json < Connection: close < Expires: Thu, 04 Mar 2010 12:18:27 UTC < http.context.path: /1/ < jersey.response: com.sun.jersey.spi.container.ContainerResponse@17646d60 < http.custom.headers: {Content-Type=text/plain} < http.request.path: /2/messages/latest.json < http.status: 200 < Transfer-Encoding: chunked I want to remove < http.context.path: /1/ < jersey.response: com.sun.jersey.spi.container.ContainerResponse@17646d60 < http.custom.headers: {Content-Type=text/plain} < http.request.path: /2/messages/latest.json < http.status: 200 So I used the proxy_hide_header directive in this way: location / { if ($arg_id) { proxy_pass http..authorized; break; } proxy_pass http..anonymous; proxy_hide_header http.context.path; proxy_hide_header jersey.response; proxy_hide_header http.request.path; proxy_hide_header http.status ; } But it doesn't work. any clues?

  Read the article

• Random Excel bug when referencing a different sheet

  - by Matteo

  I am getting a very strange error anytime I try to use a formula pointing to a cell in a different sheet from the active one (even as simple as "=Sheet2!A1"). This started happening all of a sudden, and without any change in the system - only I seem to having started having the problem since I started using a workbook from another colleague with the same issue. I'm running Excel 2003 SP3 on XP. With little variants, whenever I reference a cell in a different sheet, from any formula, and then press Enter, the formula gets written on a different cell from the one I was editing it in, and throws a REF error. Example: I start editing in cell A1 of Sheet 1, type "=", then move the cursor to cell B2 of Sheet 2 (that may contain any value), and press Enter. At this stage you would expect cell A1 in Sheet 1 to contain formula "=Sheet2!B2" and display the value in that cell. Instead what happens is that the cell remains empty, and another random cell of Sheet 1 gets populated with something like "=Sheet2!#REF!" throwing an error. Interestingly, the error does not happen when I manually type the cell reference in (ie. without moving the cursor to the second sheet). Hope this is making any sense - any ideas are welcome! Thanks.

  Read the article

• ssh_exchange_identification: Connection closed by remote host

  - by rick

  Firstly, I know that this question has been asked a million times, and I have read everything I can find and still cannot fix the problem. i am encountering this issue when ssh'ing in from my mac to my Ubuntu server on a fresh install of Ubuntu (I reinstalled because of this issue). I have SSH portmapped to 7070 because my ISP is blocking 22. On the client: bash: ssh -p 7070 -v [email protected] debug1: Reading configuration data /etc/ssh_config debug1: Connecting to address.org port 7070. debug1: Connection established. debug1: identity file /home/me/.ssh/identity type -1 debug1: identity file /home/me/.ssh/id_rsa type 1 debug1: identity file /home/me/.ssh/id_dsa type -1 ssh_exchange_identification: Connection closed by remote host Here's what I have done to try to resolve the issue: Made sure my maxstartups is ok: bash: grep MaxStartups /etc/ssh/sshd_config #MaxStartups 10:30:60 Made sure hosts.deny is clear of denials. Made sure hosts.allow has my client IP. Clear out known_hosts on client Changed ownership of /var/run to root Made sure etc/run/ssh is Made sure /var/empty exists Reinstall openssh-server Reinstall ubuntu When I run telnet localhost, I get this: telnet localhost Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused When I run /usr/sbin/sshd -t Could not load host key: /etc/ssh/ssh_host_rsa_key Could not load host key: /etc/ssh/ssh_host_dsa_key When I regenerate the keys with ssh-keygen -t rsa -f /etc/ssh/ssh_host_rsa_key ssh-keygen -t dsa -f /etc/ssh/ssh_host_dsa_key I get the same error. I am pretty sure this is the issue. Can anyone help?

  Read the article

• Keeping Xv Overlay configuration throughout an X session.

  - by kriss

  After upgrading my Linux system from Ubuntu 9.04 to Ubuntu 10.10, I suceeded correcting most problems (all related to Intel 82865G Integrated Graphics Adapter support and compiz is still not working but that's another matter) but for one I only have a partial solution. Whenever I play a video the colors are much too saturated. This is really a problem for tones of skins that appears reddish (everyone seems to be coming back from a ski vacation with deep sun burns). As this effect only occurs with videos, not with pictures, I finally figured out it was related to Video Overlays configuration and I can correct it typing: xvattr -a XV_SATURATION -v 120 This change the default saturation value, which is 500 and much too high in my case, at eye sight the correct value seems to be between 100 and 150. Now my problem is that I have to type the above command each time I run a video. If I type it before running the video it has no effect, if I close the video and open a new one, I have to type it again, etc. I tried to put it in Xsession and (logically) it has no effect either. How could I do to get the correct setting whenever I run a video without typing the above command every time ?

  Read the article

• Vyatta internet connection + hosted site on same IP

  - by boburob

  Having a small issue setting up a vyatta. The company internet and two different websites are both on the same IP. Server 1 - Has websites hosted on ports 1000 and 3000 and also has a proxy server installed to provide internet connection to the domain Server 2 - Has a website hosted on ports 80 and 433 The vyatta is correctly natting the appropriate traffic to each server, and allowing the proxy to get internet traffic, however I have a problem getting to the websites hosted on these two servers inside the domain. I believe the problem is that the HTTP request is being sent with an IP, eg: 12.34.56.78. The request will reach the website and the server will attempt to send the request back to the IP, however this is the IP of the Vyatta, so it has nowhere else to go. I thought the solution would be something like this: rule 50 { destination { address 12.34.56.78 port 1000 } inbound-interface eth1 inside-address { address 10.19.2.3 } protocol tcp type destination } But this doesnt seem to do it! UPDATE I changed the rules to the following: rule 50 { destination { address 12.34.56.78 port 443 } outbound-interface eth1 protocol tcp source { address 10.19.2.3 } type masquerade } rule 51 { destination { address 12.34.56.78 port 443 } inbound-interface eth1 inside-address { address 10.19.2.2 } protocol tcp type destination } I am now seeing traffic going between the two with Wireshark, but the website will still fail to load.

  Read the article

• What is the best way to recover from a mysql replication fail?

  - by Itai Ganot

  Today, the replication between our master mysql db server and the two replication servers dropped. I have a procedure here which was written a long time ago and i'm not sure it's the fastest method to recover for this issue. I'd like to share with you the procedure and I'd appreciate if you could give your thoughts about it and maybe even tell me how it can be done quicker. At the master: RESET MASTER; FLUSH TABLES WITH READ LOCK; SHOW MASTER STATUS; And copy the values of the result of the last command somewhere. Wihtout closing the connection to the client (because it would release the read lock) issue the command to get a dump of the master: mysqldump mysq Now you can release the lock, even if the dump hasn't end. To do it perform the following command in the mysql client: UNLOCK TABLES; Now copy the dump file to the slave using scp or your preferred tool. At the slave: Open a connection to mysql and type: STOP SLAVE; Load master's data dump with this console command: mysql -uroot -p < mysqldump.sql Sync slave and master logs: RESET SLAVE; CHANGE MASTER TO MASTER_LOG_FILE='mysql-bin.000001', MASTER_LOG_POS=98; Where the values of the above fields are the ones you copied before. Finally type START SLAVE; And to check that everything is working again, if you type SHOW SLAVE STATUS; you should see: Slave_IO_Running: Yes Slave_SQL_Running: Yes That's it! At the moment i'm in the stage of copying the db from the master to the other two replication servers and it takes more than 6 hours to that point, isn't it too slow? The servers are connected through a 1gb switch.

  Read the article

• Converting software RAID1 to RAID10 for /boot

  - by luckytaxi

  Array info: /dev/md0 - /dev/sda1 and /dev/sdb1 /dev/md2 - /dev/sda2 and /dev/sdb2 Partition info: /boot - /dev/md0 / - /dev/md1 I have two drives that are setup as RAID1 using software RAID on Redhat. I added two additional drives (same size) and I would like to conver the RAID1 to a RAID10. The problem I'm having is adding the last drive to the array. I've gotten as far as creating a RAID10 with two missing devices but as soon as I add the last drive, all hell breaks loose. It seems /dev/sda1 is the culprit. What I'm not too sure about is how to create the RAID10. I've tried the following mdadm --create /dev/md2 --level=raid10 --raid-device=4 /dev/sdc1 missing /dev/sdd1 missing I then proceeded to fail /dev/sdb1 from /dev/md0 and added that partition to /dev/md2. I proceeded to install the MBR on EACH partition since boot resides on /dev/sdx1 on each drive. As a test, all is well, I'm able to boot back into the system once I do a quick reboot. Now, when I go add the last drive /dev/sda1, it breaks. I attempted to install grub on /dev/sda1 and I get the following ... grub> root (hd0,0) /dev/sda root (hd0,0) /dev/sda Filesystem type is ext2fs, partition type 0xfd grub> setup (hd0) setup (hd0) Checking if "/boot/grub/stage1" exists... no Checking if "/grub/stage1" exists... no Error 2: Bad file or directory type At this point, the array is hosed I believe. I rebooted the server and it refuses to boot.

  Read the article

• can't ssh from mac to windows (running ssh server on cygwin)

  - by Denise

  I set up an ssh server on a fresh windows 7 machine using the latest version of cygwin. Disabled the firewall. I can ssh into it from itself, from a different windows box (using winssh), and from a linux vm. In spite of that, I tried to ssh in from two different macs, and neither would let me! This is the debug output: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 3dbuild [172.18.4.219] port 22. debug1: Connection established. debug1: identity file /Users/Denise/.ssh/identity type -1 debug1: identity file /Users/Denise/.ssh/id_rsa type 1 debug1: identity file /Users/Denise/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5 debug1: match: OpenSSH_5.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '3dbuild' is known and matches the RSA host key. debug1: Found key in /Users/Denise/.ssh/known_hosts:43 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /Users/Denise/.ssh/identity debug1: Offering public key: /Users/Denise/.ssh/id_rsa Connection closed by [ip] It shows the same output, and fails at the same place, whether I have put my public key on the ssh server or not. Any help would be appreciated-- hopefully someone has run into this before?

  Read the article

• ntpdate cannot receive data

  - by Hengjie

  I have a problem where running ntpdate on my server doesn't return any data therefore I get the following error: [root@server etc]# ntpdate -d -u -v time.nist.gov 12 Apr 01:10:09 ntpdate[32072]: ntpdate [email protected] Fri Nov 18 13:21:21 UTC 2011 (1) Looking for host time.nist.gov and service ntp host found : 24-56-178-141.co.warpdriveonline.com transmit(24.56.178.141) transmit(24.56.178.141) transmit(24.56.178.141) transmit(24.56.178.141) transmit(24.56.178.141) 24.56.178.141: Server dropped: no data server 24.56.178.141, port 123 stratum 0, precision 0, leap 00, trust 000 refid [24.56.178.141], delay 0.00000, dispersion 64.00000 transmitted 4, in filter 4 reference time: 00000000.00000000 Thu, Feb 7 2036 14:28:16.000 originate timestamp: 00000000.00000000 Thu, Feb 7 2036 14:28:16.000 transmit timestamp: d3303975.1311947c Thu, Apr 12 2012 1:10:13.074 filter delay: 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 filter offset: 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 delay 0.00000, dispersion 64.00000 offset 0.000000 12 Apr 01:10:14 ntpdate[32072]: no server suitable for synchronization found I have tried Googling the 'no server suitable for synchronization found' error online and I have tried disabling my firewall (running iptables -L returns no rules). I have also confirmed with my DC that there are no rules that are blocking ntp (port 123). Does anyone have any ideas on how I may fix this? Btw, this is what the output should look like on a working server in another DC: 11 Apr 19:01:24 ntpdate[725]: ntpdate [email protected] Fri Nov 18 13:21:17 UTC 2011 (1) Looking for host 184.105.192.247 and service ntp host found : 247.conarusp.net transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) receive(184.105.192.247) transmit(184.105.192.247) server 184.105.192.247, port 123 stratum 2, precision -20, leap 00, trust 000 refid [184.105.192.247], delay 0.18044, dispersion 0.00006 transmitted 4, in filter 5 reference time: d330364e.e956694f Wed, Apr 11 2012 18:56:46.911 originate timestamp: d3303765.8702d025 Wed, Apr 11 2012 19:01:25.527 transmit timestamp: d3303765.73b213e3 Wed, Apr 11 2012 19:01:25.451 filter delay: 0.18069 0.18044 0.18045 0.18048 0.18048 0.00000 0.00000 0.00000 filter offset: -0.00195 -0.00197 -0.00211 -0.00202 -0.00202 0.000000 0.000000 0.000000 delay 0.18044, dispersion 0.00006 offset -0.001970

  Read the article

• Office 2003 Service Pack 3- Not able to install

  - by kabirrao

  I am trying to install Office 2003 SP3 on a windows 2003 EE server (used as a terminal server) which already have office 2003 SP2. I am getting an error that says "Update can not be applied". Below are the eventviewer entries for Application: _ Event Type: Warning Event Source: MsiInstaller Event Category: None Event ID: 1015 Date: 1-2-2010 Time: 5:51:22 User: Domain\domainadmin Computer: TER01 Description: Failed to connect to server. Error: 0x800401F0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. _ Event Type: Information Event Source: MsiInstaller Event Category: None Event ID: 11708 Date: 1-2-2010 Time: 5:52:23 User: Domain\domainadmin Computer: TER01 Description: Product: Microsoft Office Professional Edition 2003 -- Installation failed. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 7b 39 30 31 31 30 34 30 {9011040 0008: 39 2d 36 30 30 30 2d 31 9-6000-1 0010: 31 44 33 2d 38 43 46 45 1D3-8CFE 0018: 2d 30 31 35 30 30 34 38 -0150048 0020: 33 38 33 43 39 7d 383C9} _ Event Type: Information Event Source: McLogEvent Event Category: None Event ID: 257 Date: 1-2-2010 Time: 5:52:23 User: NT AUTHORITY\SYSTEM Computer: TER01 Description: Would be blocked by access protection rule (rule is in warn-only mode) (Common Standard Protection:Prevent common programs from running files from the Temp folder).

  Read the article

• Gathering buslogic SCSI hardware and virtual machine operating system

  - by Julian

  I'm trying to use Powershell to get SCSI hardware from several virtual servers and get the operating system of each specific server. I've managed to get the specific SCSI hardware that I want to find with my code, however I'm unable to figure out how to properly get the operating system of each of the servers. Also, I'm trying to send all the data that I find into a csv log file, however I'm unsure of how you can make a powershell script create multiple columns. Here is my code (almost works but something's wrong): $log = "C:\Users\me\Documents\Scripts\ScsiLog.csv" Get-VM | Foreach-Object { $vm = $_ Get-ScsiController -VM $vm | Where-Object { $_.Type -eq "VirtualBusLogic" } | Foreach-Object { get-VMGuest -VM $vm } | Foreach-Object{ Write-output $vm.Guest.VmName >> $log } } I don't receive any errors when I run this code however whenever I run it I'm only getting the name of the servers and not the OS. Also I'm not sure what I need to do to make the OS appear in a different column from the name of the server in the csv log that I'm creating. What do I need to change in my code to get the OS version of each virtual machine and output it in a different column in my csv log file? EDIT: Here's a more in depth look at things I've tried that have all failed: Get-VM | Foreach-Object { $vm = $_ $svm = Get-ScsiController -VM $vm | Where-Object { $_.Type -eq "VirtualBusLogic" } Foreach-Object {get-VMGuest -VM $svm } | Foreach-Object{Write-output $svm >> $log} } #Get-VM | Foreach-Object { # $vm = $_ # Get-ScsiController -VM $vm | Where-Object { $_.Type -eq "VirtualBusLogic"} #| write-host $vm # | Foreach-Object { # # #get-VMGuest -VM $_ | # #write-host $vm # #get-VMGuest -VM $vm } | Foreach-Object{ # #write-output $vm.VmName >> $log # #write-output $vm.guest.VmName, get-VmGuest -VM $vm >> $log NO GOOD # # Write-host $vm.Guest.VmName #+ get-vmGuest -vm $VM >> $log # # # } # } I'm not sure why get-VmGuest fails though. I'm getting the scsi hardware, filtering the hardware to only get buslogic, and then wanting to get the operating system of just the filtered VMs. I don't see where my code fails though.

  Read the article

• Failing to load rootfs: Ubuntu 10 + grub2 + rootfs ext4 w/ RAID1

  - by James

  I am having problems booting a new Ubuntu 10 (server) install. My primary HD (/dev/sda) is laid out as follows: Device Boot Start End Blocks Id System /dev/sda1 * 1 18 144553+ 83 Linux <-- /BOOT /dev/sda2 19 182401 1464991447+ 5 Extended /dev/sda5 19 2207 17583111 fd Linux raid autodetect /dev/sda6 2208 11934 78132096 fd Linux raid autodetect <-- / (ROOTFS) /dev/sda7 11935 182401 1369276146 fd Linux raid autodetect The rootfs is part of a RAID1 (software) array (currently degraded): # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md2 : active raid1 sda6[1] 78132032 blocks [2/1] [_U] The UUIDs for the partitions are as follows: # blkid /dev/sda1 /dev/sda1: UUID="b25dd301-41b9-4f4d-9b0a-0e31713dd74c" TYPE="ext2" # blkid /dev/sda6 /dev/sda6: UUID="af7b9ede-fa53-c0c1-74be-31ec752c5cd5" TYPE="linux_raid_member" # blkid /dev/md2 /dev/md2: UUID="a0602d42-6855-482f-870c-6f6ecdcdae3f" TYPE="ext4" Finally, I have my grub2 menuentry setup as follows: ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-25-server' --class ubuntu --class gnu-linux --class gnu --class os { insmod ext2 insmod raid insmod mdraid set root='(hd0,1)' search --no-floppy --fs-uuid --set b25dd301-41b9-4f4d-9b0a-0e31713dd74c linux /vmlinuz-2.6.32-25-server root=UUID=a0602d42-6855-482f-870c-6f6ecdcdae3f ro nosplash noplymouth initrd /initrd.img-2.6.32-25-server } When I attempt to boot, grub loads OK, however I eventually get the following error message: Gave up waiting for root device. ALERT /dev/disk/by-uuid/a0602d42-6855-482f-870c-6f6ecdcdae3f does not exist. Dropping to a shell! If from the grub bootloader I open a grub command line, I can ls (hd0,) and it lists the correct partitions with the UUIDs as shown above - sda6 shows 'a0602d42-6855-482f-870c-6f6ecdcdae3f' (the RAID UUID). If I ls (md2)/ it properly lists all the files on the RAID1 filesystem (ext4) so it doesn't appear to be an issue accessing the raid device. Does anyone have any suggestions as to what the problem might be? I can't figure this one out.

  Read the article

• Printer Naming Conventions

  - by John

  I am working on building a new AD print server and have been pondering the idea of renaming the printers. Right now we have a mix of names that varies between a mashup of some that reference location, some that reference functional area, and some that are rather generic. Some examples include the following: Dell 5210 - Building Name HP 4350 - Functional Area Dell Color 3100 - Location and Building Number HP 6500 - Mailroom I was curious what other people used to name their printers with. What conventions do you use and how to design a method that will be able to be used for a while without needing to rename them all again. Also, the naming methodology needs to be understandable for regular computing users so that they can relatively easily find the printer that they need. I was looking at some ideas from here, but I was not sure how practical some of them are. Any help that you can provide is appreciated. Note: I have reviewed many of the postings on here in relation to server naming conventions and found that they were not specific enough for the use case I present above.

  Read the article

• how can i move ext3 partition to the beginning of drive without losing data?

  - by Felipe Alvarez

  I have a 500GB external drive. It had two partitions, each around 250GB. I removed the first partition. I'd like to move the 2nd to the left, so it consumes 100% of the drive. How can this be accomplished without any GUI tools (CLI only)? fdisk Disk /dev/sdd: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc80b1f3d Device Boot Start End Blocks Id System /dev/sdd2 29374 60801 252445410 83 Linux parted Model: ST350032 0AS (scsi) Disk /dev/sdd: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 2 242GB 500GB 259GB primary ext3 type=83 dumpe2fs Filesystem volume name: extstar Last mounted on: <not available> Filesystem UUID: f0b1d2bc-08b8-4f6e-b1c6-c529024a777d Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal dir_index filetype needs_recovery sparse_super large_file Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 15808608 Block count: 63111168 Reserved block count: 0 Free blocks: 2449985 Free inodes: 15799302 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8208 Inode blocks per group: 513 Filesystem created: Mon Feb 15 08:07:01 2010 Last mount time: Fri May 21 19:31:30 2010 Last write time: Fri May 21 19:31:30 2010 Mount count: 5 Maximum mount count: 29 Last checked: Mon May 17 14:52:47 2010 Check interval: 15552000 (6 months) Next check after: Sat Nov 13 14:52:47 2010 Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: d0363517-c095-4f53-baa7-7428c02fbfc6 Journal backup: inode blocks Journal size: 128M

  Read the article

• Removing trailing slashes in WordPress blog hosted on IIS

  - by Zishan

  I have a WordPress blog hosted in my IIS virtual directory that has all URLs ending with a forward slash. For example: http://www.example.com/blog/ I have the following rules defined in my web.config: <rule name="wordpress" patternSyntax="Wildcard"> <match url="*" /> <conditions> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> </conditions> <action type="Rewrite" url="index.php" /> </rule> <rule name="Redirect-domain-to-www" patternSyntax="Wildcard" stopProcessing="true"> <match url="*" /> <conditions> <add input="{HTTP_HOST}" pattern="example.com" /> </conditions> <action type="Redirect" url="http://www.example.com/blog/{R:0}" /> </rule> In addition, I tried adding the following rule for removing trailing slashes: <rule name="Remove trailing slash" stopProcessing="true"> <match url="(.*)/$" /> <conditions> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> </conditions> <action type="Redirect" redirectType="Permanent" url="{R:1}" /> </rule> It seems that the last rule doesn't work at all. Anyone around here who has attempted to remove trailing slashes from WordPress blogs hosted on IIS?

  Read the article

• Anonymous Login attemps from IPs all over Asia, how do I stop them from being able to do this?

  - by Ryan

  We had a successful hack attempt from Russia and one of our servers was used as a staging ground for further attacks, actually somehow they managed to get access to a Windows account called 'services'. I took that server offline as it was our SMTP server and no longer need it (3rd party system in place now). Now some of our other servers are having these ANONYMOUS LOGIN attempts in the Event Viewer that have IP addresses coming from China, Romania, Italy (I guess there's some Europe in there too)... I don't know what these people want but they just keep hitting the server. How can I prevent this? I don't want our servers compromised again, last time our host took our entire hardware node off of the network because it was attacking other systems, causing our services to go down which is really bad. How can I prevent these strange IP addresses from trying to access my servers? They are Windows Server 2003 R2 Enterprise 'containers' (virtual machines) running on a Parallels Virtuozzo HW node, if that makes a difference. I can configure each machine individually as if it were it's own server of course... UPDATE: New login attempts still happening, now these ones are tracing back to Ukraine... WTF.. here is the Event: Successful Network Logon: User Name: Domain: Logon ID: (0x0,0xB4FEB30C) Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: REANIMAT-328817 Logon GUID: - Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: 94.179.189.117 Source Port: 0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Here is one from France I found too: Event Type: Success Audit Event Source: Security Event Category: Logon/Logoff Event ID: 540 Date: 1/20/2011 Time: 11:09:50 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: QA Description: Successful Network Logon: User Name: Domain: Logon ID: (0x0,0xB35D8539) Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: COMPUTER Logon GUID: - Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: 82.238.39.154 Source Port: 0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• sysbench memory test on ec2 small instance

  - by caribio

  I'm seeing a problem with sysbench memory test (the default version that's compiled in). This is on Ubuntu Maverick, sysbench installed via apt-get install sysbench. Running the same thing on Ubuntu @ Rackspace worked just as expected. While the CPU and I/O tests worked fine on EC2 servers, the memory test just runs without doing anything (notice the 0M in the test results). The instance used was the publicly available 'stock' Ubuntu image with no changes to it: ./ec2-run-instances ami-ccf405a5 --instance-type m1.small --region us-east-1 --key mykey Supplying more arguments (such as: --memory-block-size=1K --memory-total-size=102400M) didn't help. What am I doing wrong? Thanks. sysbench --num-threads=4 --test=memory run sysbench 0.4.12: multi-threaded system evaluation benchmark Running the test with following options: Number of threads: 4 Doing memory operations speed test Memory block size: 1K Memory transfer size: 0M Memory operations type: write Memory scope type: global Threads started! Done. Operations performed: 0 ( 0.00 ops/sec) 0.00 MB transferred (0.00 MB/sec) Test execution summary: total time: 0.0003s total number of events: 0 total time taken by event execution: 0.0000 per-request statistics: min: 18446744073709.55ms avg: 0.00ms max: 0.00ms Threads fairness: events (avg/stddev): 0.0000/0.00 execution time (avg/stddev): 0.0000/0.00

  Read the article

• Custom Dreamweaver DocTypes

  - by Hugh Guiney

  Dreamweaver CS5 with Dreamweaver HTML5 Pack 1.2.7 Windows 7 x64 When I go to create a new document and select the HTML5 DocType, Dreamweaver gives me the legacy encoding/character set declaration: <meta http-equiv="Content-Type" content="text/html; charset=utf-8"> I want to replace it with the new, abbreviated style: <meta charset="utf-8"> The relevant file seems to be %ProgramFiles(x86)%\Adobe\Adobe Dreamweaver CS5\configuration\DocumentTypes\NewDocuments\Default.html, which has a blank charset, that is then apparently replaced with the appropriate character set dynamically: <meta http-equiv="Content-Type" content="text/html; charset="> I changed it, but then new documents show up like this: <meta charset=""> <title>Untitled Document</title> <meta http-equiv="Content-Type" content="text/html; charset=utf-8"> It seems Dreamweaver added the legacy declaration back in after my modification—and as far as I can tell, there's no way to specify that the charset definition should go in-between the quotes, either. Additionally, any modifications to Default.html apply to every DocType, whereas I only want this change to apply to the HTML5 DocType. Is there anything in the configuration files that would allow me to make any of these customizations? If not, is there an extension that does it?

  Read the article

• ssh - "Connection closed by xxx.xxx.xxx.xxx" - using password

  - by Michael B

  I attempted to create an new user account that I wish to use to log in using ssh. I did this (in CentOs): /usr/sbin/adduser -d /home/testaccount -s /bin/bash user passwd testaccount This is the error I receive when trying to log in via ssh: ~/.ssh$ ssh -v [email protected] OpenSSH_5.1p1 Debian-5ubuntu1, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to xxx.xxx.xxx [xxx.xxx.xxx.xxx] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/identity type -1 debug1: identity file /home/user/.ssh/id_rsa type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: identity file /home/user/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.3 debug1: match: OpenSSH_4.3 pat OpenSSH_4* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'xxx.xxx.xxx.xxx' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:8 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information No credentials cache found debug1: Unspecified GSS failure. Minor code may provide more information No credentials cache found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Offering public key: /home/user/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Trying private key: /home/user/.ssh/identity debug1: Trying private key: /home/user/.ssh/id_dsa debug1: Next authentication method: password testaccount@xxx's password: Connection closed by xxx.xxx.xxx.xxx The "connection closed" message appeared immediately after entering the password (if I enter the wrong password it waits and then prompts for another password) I am able to log in from the same computer using other accounts that had been setup previously. When logged into the remote machine I am able to do 'su testaccount' Thanks for your time.

  Read the article

• Trouble getting started with the STEALTH monitoring package

  - by dlanced

  Is anyone here familiar with the Linux-based STEALTH package (for monitoring FS integrity of client systems)? I'm trying to get started with a very simple configuration, but I'm running into trouble (this is running under Ubuntu 14.04): Config line `USE BASE/root/stealth/10.0.0.79' invalid STEALTH (2.11.02) started at Fri, 30 May 2014 15:25:00 +0000 Program terminated due to non-zero exit value for -type f -exec /usr/bin/sha1sum {} \; (EOC Fri May 30 15:25:00 2014 127) Stealth is creating a binary tmp file in the Stealth server root and generating a "report" file in the start directory, but not much else. Regarding the "USE BASE...invalid" error, and just to be sure, I manually created the directories in /root, but it didn't help. And, by the way, I am running stealth with sudo. Everything seems to be configured correctly: I'm able to ssh into root@client from the stealth machine without a password Here's my "policy" file (I've removed the email directives just for simplicity): DEFINE SSHCMD /usr/bin/ssh [email protected] -T -q exec /bin/bash --noprofile DEFINE EXECSHA1 -xdev -perm +u+s,g+s ( -user root -or -group root ) \ -type f -exec /usr/bin/sha1sum {} \; USE BASE/root/stealth/10.0.0.79 USE SSH ${SSHCMD} USE DD /bin/dd USE DIFF /usr/bin/diff USE PIDFILE /var/run/stealth- USE REPORT report USE SH /bin/sh GET /usr/bin/sha1sum /root/tmp LABEL \nchecking the client's /usr/bin/find program CHECK LOG = remote/binfind /usr/bin/sha1sum /usr/bin/find LABEL \nsuid/sgid/executable files uid or gid root on the / partition CHECK LOG = remote/setuidgid /usr/bin/find / ${EXECSHA1} LABEL \nconfiguration files under /etc CHECK LOG = remote/etcfiles \ /usr/bin/find /etc -type f -not -perm /6111 \ -not -regex "/etc/(adjtime\|mtab)"\ -exec /usr/bin/sha1sum {} \; Any ideas? Thanks,

  Read the article

• Codecs, Premiere Pro & Quicktime: Import or Play Error

  - by Nchpmn

  Original Question I've been using a FS-H200 (not the Pro variant) recorder with a JVC ProHD camera. I have been shooting with the DTE FORMAT to Quicktime (.mov). I copied the files to an external hard drive and am now trying to edit. The files will play back in VLC, as they would be expected to. However they will not import into Adobe Premiere CS5.5, instead giving an error: Unsupported format or damaged file. Quicktime gives the following error when attempting to play the files: Error -2002: a bad public movie atom was found in the movie (Filename) To try and fix this, I have installed the following codec packs: K-Lite Codec Pack 64-bit Full (version 5.9, latest) K-Lite Codec Pack 32-bit Full (version 8.4, latest) MainConcept Codec Suite (Broadcast) v5.1 for Adobe CS5 Reinstalled Quicktime with new download from Apple The same errors and problems still exist. From this I can assume that there is an issue with Quicktime and that is what Premiere is using as an encoder/decoder for the codec. Is there any way to fix this? From looking at the "Codec Information" from VLC: Stream 0 Type: Video Codec: MPEG-1/2 (mpgv) Language: English Resolution: 1280 x 720 Frame Rate: 25 Stream 1 Type: Audio Codec: PCM S16 BE (twos) Language: English Channels: Stereo Sample Rate: 48000 Hz Bits per sample: 16 Other computer specs: Windows 7 Professional 64-bit (SP1) Gigabyte Z68X-UD3-B3 Intel i7-2600K 16GB DDR3 2TB WD 7200RPM SATA 6Gb/s LaCie d2 Quadra 2TB v3 7200RPM (External HDD) NVIDIA GeForce GTX 560 Ti Golden Sample Updates 2012-03-11 @ 2050 AEDT MPEG Steamclip doesn't recognise, play or convert the footage. File open error: unrecognised file type. [Open Anyway] File open error: can't find video or audio tracks. 2012-03-24 @ 1920 AEDT Had to transcode the footage. :(

  Read the article

• Clone Microsoft VM > SharePoint issues

  - by Rob

  Hi, We have an existing (production) Hyper-V VM that I want to clone to create a staging server. This server is NOT on a domain/active-directory - uses all local computer accounts. It is Windows 2008 OS, SharePoint 2007, SQL server 2008, Reporting Services, and some custom line-of-business web-applications. We rename the server etc as per the documentation we have, but are having troubles specifically with SharePoint. Some of the sites do not come up, and some issues adding/updating site settings such as site owners. Does anyone know of a definitive resource to this process? thanks Update: We seem to have most working, but the Shared Service Provider, and the SSP's admin site, are not working. In addition, the custom web-parts that reference IIS Session objects are failing (which seem to be related to the Share Service Provider). All the Windows user accounts for various services are renamed during the server cloning, but the windows account names in SQL server are not automatically changed. We've tried to change them in SQL server but still does not seem to work Seems like allot of work - and am thinking that there must be some guidance out there. also getting this: NullReferenceException: Object reference not set to an instance of an object.] Microsoft.Office.Server.Administration.SqlSessionStateResolver.System.Web. IPartitionResolver.ResolvePartition(Object key) +135

  Read the article

• How can I boot from .iso images stored on the harddrive ?

  - by user29701

  I want to put a .iso file of a bootable linux CD on the harddrive of my computer. I want to have it boot using grub (or lilo), and have it boot from the .iso file as if the .iso was a real CD in the CDROM drive. Here is a page that makes reference to doing this, but instead of a .iso file it is a .img file of a floppy or a whole harddisk installation: http://grub4dos.sourceforge.net/wiki/index.php/Grub4dos%5Ftutorial That page makes reference to "cdrom emulation is not supported", but I don't know if it is not supported in grub, or if what want to do is completely impossible. Apparently Epidemic Linux (and maybe Knoppix ?) have a "bootfrom" parameter: "Using the parameter “bootfrom=/partition/path” you can start Epidemic from an ISO image located anywhere on the HD without having to create a DVD. This is very handy for testing the system." (From www.epidemiclinux.org/ ) Drew P.S. I am NOT interested in installing the CD on the harddrive. If I could have a dozen .iso's on the harddrive, I would like to be able to select them from grub and boot each of them.

  Read the article

< Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >