Search Results

Search found 12367 results on 495 pages for 'disk io'.

Page 456/495 | < Previous Page | 452 453 454 455 456 457 458 459 460 461 462 463  | Next Page >

• Recovering data from failed Raid configuration with 4 drives and two raid sets (Asus P6T / Intel ICH10r)

  - by user56365

  I've added the complete detailed version for my question below for those who can help, but want to quickly summarize my question first. I setup two Raid arrays using (4) WD Raptors, a striped set for the OS and 1+0 set for crucial data. After booting once out of the 50 times a cable fell out, the drive wasn't recognized in the array anymore. After trying to fix it, another drive did the same. I now have two drives remaining, luckily with the parity information. I know the striped set is gone, but I need the data on the other set. Can anyone recommend anything to recover the data, or fix the two drives that doesn't allow the raid controller to recognize the drives, even though they are listed on the utility screen as still apart of the configuration but that they are not found? More Details I recently upgraded to a ASUS P6T motherboard with an Intel ICH10R raid controller and changed my previous 4 drive raid array from strictly a Raid 1+0 set to a Raid 0 for the OS/Page/Scratch drive and a Raid 1+0 set for crucial data. I never had problems after upgrading with my configuration, even when a drive died and was replaced. I managed to rebuild the array fine. Unfortunately this time around, a cable came unattached and I booted my system up until the raid status screen with the degraded error. This shouldn't have been a problem, but after I attached the drive it was no longer recognized as a member in the array. Both drives actually show up as a non-member disk. I've spent a very, very long time online trying to find information or support and haven't had much luck. After spending time trying to scan the drive for errors, damaged partition info, etc.. another drive in the set decided it didn't want to be recognized as a part of the array. At this point, I have two out of the four drives still functioning, but the Raid 1+0 array went from degraded to failed and I must find a way to retrieve that data. I think the two drives still in the array have the parity information because they show up as OS (110GB),BACKUP(80GB) and OS:1(110GB),BACKUP(80GB) under windows data management. The other two are simply 74gb Raw unallocated Is it possible recover the data using those two drive only, and which tool would I use? Could it be a simple partition table or any other error that is repairable with hard drive utilities out there? I know the Raid 0 set is done for, but I would assume because the correct drives failed in a 1+0 config to save the data I can retrieve it some how.

  Read the article

• Spotlight Infinite Indexing issue (external data drive)

  - by Manca Weeks

  This is an external drive, formerly a boot drive which is now in use only to access music files (sibelius, audio, midi, live, logic etc.) without transferring the data into a new boot system, partly because of the issue I am about to describe, but mostly because the majority of the data is mainly there for archival purposes. The user is a composer and prominent musician and needs to be able to rehash the data at will. I have tried several things - here is a list: - make complete filesystem clone with antonio diaz's ddrescue - run Disk Warrior on copy, repair whatever errors occurred - wipe out all ACLs on entire drive - set all permissions to the same value - wide open 777 - remove any system data (applications, system files, including hidden files to the best of my knowledge) by selecting only non-system/app data and using Carbon Copy Cloner to put only the data of interest onto a newly formatted drive - transfer data to newly formatted drive folder by folder, resetting the spotlight index in between adding each to observe for issues (interesting here is that no issues occurred except for in Documents folder - when I transferred only the Documents folder to a newly formatted drive on its own - no trouble. It appears almost as thought it may not be the content but the quantity or specific combination of data that results in problems) - use DataRescue to transfer the data to yet another newly formatted drive to expose any missed hidden files Between each of the above steps I stopped Spotlight (search for anything beginning with md in Activity Monitor - All Processes and quitting it), deleted the .Spotlight-V100 directory from the affected drive. Restart Splotlight indexing by adding drive to Spotlight privacy list and removing it. In each case the same issue occurs - Spotlight begins indexing normally (or so it seems), then the index estimated time increases, usually to 4 hours remaining. This is where it gets stuck and continues to predict 4 hours remaining but never finishes. Sometimes I can't eject the drive and have to quit the md.. processes from Activity Monitor to be able to eject the drive without Force Eject. Once I disconnect the drive after the 4 hours remaining situation - if I reattach it, Spotlight forever estimates remaining time and never gets going again. So there it is. It is apparently not a filesystem issue, not a permissions issue and not tied to any particular piece of hardware or protocol (used USB and FW drives). I have tried this on several machines (3 to be precise) and in 10.5.8 and 10.6.5. Simply disabling Spotlight on this volume is not an option because the owner has no clue where things are as the data on the volume dates back to music projects and compositions from 2003 and before. He needs to be able to query for results. Anyone got any ideas? Thanks, M

  Read the article

• Melting Laptop Power Supply Tip

  - by AlReece45

  Several (6-7) months ago, my laptop power supply cord got a cut in it and stopped working. Having gotten cheap (and short) power supplies in the past, I decided to buy 2 brand new ones from the manufacturer (ASUS). Now, I used my laptop a little less than usual between February and March. During that time I noticed a few times that the power supply, even though plugged in, did not provide power. Often the computer would just off on me. I figured it was just that one power supply being bad. I had left the alternate at my parent's house in another state and asked them to ship it to me. Now, at work the other day I wanted to get a file off the of hard disk. So I booted it up, knowing that it had a low battery, plugged it in. During the first 2 minutes of use, I was told that the battery was low and I should plug it in. I unplugged it, inspected the end (Being plugged in, this was suspicious), and decided I shouldn't plug it back in-- the plastic on the tip was melting from the heat of the metal on the tip. The computer had simply booted up and I had the file-manager open. It had not been on for more than 10 hours. Now I know that computers tend to get pretty hot. However, the melting point of plastic is usually above 200C.. so that's much hotter than the computer should be generating. I went and bought a THIRD power supply. This time a universal one from Best Buy (it was very fast to buy and test). I tried it out on the computer and it's tip is melting as well. My older laptop that uses the universal power supply uses it perfectly (has been about a week and a part of use now). I have tried using the computer without the battery, with the same effect. Obviously, this is not a problem with the power supply. My room mate and I being trained computer techs were contemplating taking the computer apart and desoldering and resoldering on the power tip. (The computer is about 6 months out of its 2-year warranty). We're hoping that will correct the issue as I would prefer to devote my money on a Good Desktop rather than yet ANOTHER $1200+ laptop. Is there any thing I'm missing here that might cause the the tip on the power unit to melt?

  Read the article

• Logitech Optical Mouse Frozen In Middle of Windows XP Pro Screen

  - by Code Sherpa

  Hi. I have a Logitech Optical Mouse/Keyboard. I have been using them just fine with the system drivers for almost a year now. I recently updated my Kaspersky software and rebooted. Now the mouse is frozen in the middle of my screen. I am not able to login to the Windows XP Pro box that has the frozen mouse (because i can't work the mouse) but am able to remote desktop to this computer. Things I know / have tried: When I boot on the problem computer, I am able to use the keyboard, but not the mouse. I have installed the latest version of Logitech's SetPoint (with the updated drivers) on the problem computer (via remote desktop) and that didn't seem to matter. I bought new batteries for the mouse and that didn't matter. I have tried the mouse/keyboard on another computer and the mouse works just fine there. My suspicion is that the Kaspersky install has overwritten a driver of some sort. Things I have not done (and would appreciate detailed steps if you feel this is the way to go): 1) Uninstalled all the mouse drivers on the machine and reboot. Then, reinstall. Note: When I get to the Device Manager I don't see an option for Human Interface Devices (where the mouse device is). Here are my options: Computer, Disk Drives, DVD/CD-Rom drives, Floppy controllers, IDE ATA/ATAPI, Imaging devices, Network Adapters, Other devices, Ports, Processors, Sound, video, and gaming, System devices, USB controllers. Also, I should point out that Video Controller is the only thing under Other devices and it has a yellow exclamation mark. The same is true for all the items under Universal Serial Bus controllers. I think this means I have to update my BIOS but, since my mouse was working just fine without doing that, I don't think that is my problem. So, how do I get to my Mouse Device? 2) Update my BIOS. Note: As pointed out above, I don't think this matters as my mouse was working just fine under my computer's current BIOS version. Thanks for your help.

  Read the article

• How do you backup 40+ Centos5.5 servers?

  - by John Little

  We are embarrassed to ask this question. Apologies for our lack of UNIX expertise. We have inherited 40+ centos 5.5 servers, and don't know how to back them up. We need low level clone type images so that we could restore the servers from scratch if we had to replace the HDs etc. We have used the "dd" command, but we assume this only works if you want to back up one local disk to another, not 40 servers to one server with an external USB HD attached. All 40 servers have a pair of mirrored disks (dont know if its HW or SW raid). Most only have 100MB used. SErvers are running apache, zend, tomcat, mysql etc. Ideally we dont want to have to shut them down to backup (but could). We assume that standard unix commands like tar, cpio, rsync, scp etc. are of no use as they only copy files, not partitions, all attributes, groups etc. i.e. do not produce a result which can simply be re-imaged to a new HD to get the serer back from dead. We have a large SAN, a spare windows box and spare unix boxes, but these are only visible to one layer in the network. We have an unused Dell DL2000 monster tape unit, but no sw or documentation for it. WE have a copy of symantec backup exec, but we have no budget for unix client licenses. (The company has negative amounts of money). We need to be able to initiate the backup remotely, as we can only access the servers in person in an emergency (i.e. to restore) Googling returns some applications to do this, e.g. clonezilla - looks difficult to install and invasive. Mondo, only seems to support backup if you are local to the machine. Amanda might be an option, but looks like days/weeks of work to learn and setup? Is there anything built into Centos, or do we have to go the route of installing, learning and configuring a set of backup softwares? Any ideas? This must be a pretty standard problem which goggling doesnt give an obvious answer.

  Read the article

• Lots of dropped packages when tcpdumping on busy interface

  - by Frands Hansen

  My challenge I need to do tcpdumping of a lot of data - actually from 2 interfaces left in promiscuous mode that are able to see a lot of traffic. To sum it up Log all traffic in promiscuous mode from 2 interfaces Those interfaces are not assigned an IP address pcap files must be rotated per ~1G When 10 TB of files are stored, start truncating the oldest What I currently do Right now I use tcpdump like this: tcpdump -n -C 1000 -z /data/compress.sh -i any -w /data/livedump/capture.pcap $FILTER The $FILTER contains src/dst filters so that I can use -i any. The reason for this is, that I have two interfaces and I would like to run the dump in a single thread rather than two. compress.sh takes care of assigning tar to another CPU core, compress the data, give it a reasonable filename and move it to an archive location. I cannot specify two interfaces, thus I have chosen to use filters and dump from any interface. Right now, I do not do any housekeeping, but I plan on monitoring disk and when I have 100G left I will start wiping the oldest files - this should be fine. And now; my problem I see dropped packets. This is from a dump that has been running for a few hours and collected roughly 250 gigs of pcap files: 430083369 packets captured 430115470 packets received by filter 32057 packets dropped by kernel <-- This is my concern How can I avoid so many packets being dropped? These things I did already try or look at Changed the value of /proc/sys/net/core/rmem_max and /proc/sys/net/core/rmem_default which did indeed help - actually it took care of just around half of the dropped packets. I have also looked at gulp - the problem with gulp is, that it does not support multiple interfaces in one process and it gets angry if the interface does not have an IP address. Unfortunately, that is a deal breaker in my case. Next problem is, that when the traffic flows though a pipe, I cannot get the automatic rotation going. Getting one huge 10 TB file is not very efficient and I don't have a machine with 10TB+ RAM that I can run wireshark on, so that's out. Do you have any suggestions? Maybe even a better way of doing my traffic dump altogether.

  Read the article

• turn off disable the performance cache

  - by jessie

  OK I run a streaming website and my CMS is giving me an error when uploading videos "Failed To Find Flength File" ok so I did some research. The answer I got from the coder was below. I did do all that, but the only thing I could not do is turn off what he refers to as performance cache, talked about in the last sentence... I am on a Cent OS Assuming the script is set up properly, you are probably dealing with some kind of write-caching. Some servers perform write-caching which prevents writing out the flength file or the entire CGITemp file during the upload. The flength file or the CGITemp file do not actually hit the disk until the upload is complete, making it worthless for reporting on progress during the upload. This may be fixed using a .htaccess file assuming your host supports them. Here is a link to an excellent tutorial on using .htaccess files. I strongly recommend giving it a quick read before attempting to install your own .htaccess file. 1. A mod_security module for Apache. To fix it just create a file called .htaccess (that's a period followed by "htaccess") and put the following lines in that file. Upload the file into the directory where the Uber-Uploader CGI ".pl" scripts resides, or in some directory above it (like your server's DOCUMENT_ROOT, i.e. the top-level of your webspace). htaccess files must be uploaded as ASCII mode, not BINARY. You may need to CHMOD the htaccess file to 644 or (RW-R--R--). # Turn off mod_security filtering. SecFilterEngine Off # The below probably isn't needed, # but better safe than sorry. SecFilterScanPOST Off If the above method does not work, try putting the following lines into the file SetEnvIfNoCase Content-Type \ "^multipart/form-data;" "MODSEC_NOPOSTBUFFERING=Do not buffer file uploads" mod_gzip_on No 2. "Performance Cache" enabled on OS X SERVER. If you're running OS X Server and the progress bar isn't working, it could be because of "performance caching." Apparently if ANY of your hosted sites are using performance caching, then by default, all sites (domains) will attempt to. The fix then is to disable the performance cache on all hosted sites.

  Read the article

• Which hardware to VM ratio for Build-Server virtualization?

  - by Martin

  Let's start with saying that I'm a total noob wrt. to server virtualization. That is, I use VMs often during development, but they're simple desktop machine things for me. Now to my problem: We have two (physical) build servers, one master, one slave running Jenkins to do daily tasks and build (Visual C++ Builds) our release packages for our software. As such these machines are critical to our company, because we do lot's releases and without a controlled environment to create them, we can't ship fixes. (And currently there's no proper backup of these machines in place, because they do not hold any data as such - it just would be a major pain to setup them again should they go bust. (But setting up backup that I'd know would work in case of HW failure would even be more pain, so we have skipped that until now.)) Therefore (and for scaling purposes) we would like to go virtual with these machines. Outsourcing to the cloud is not an option, not at all, so we'll have to use on-premises hardware and VM hosts. Each Build-Server (master or slave) is a fully configured (installs, licenses, shares in case of the master, ...) Windows Server box. I would now ideally like to just convert the (two) existing physical nodes to VM images and run them. Later add more VM slave instances as clones of the existing ones. And here begin my questions: Should I go for one VM per one hardware-box or should I go for something where a single hardware runs multiple VMs? That would mean a single point of failure hardware wise and doesn't seem like a good idea ... or?? Since we're doing C++ compilation with Visual Studio, I assume that during a build the hardware (processor cores + disk) will be fully utilized, so going with more than one build-node per hardware doesn't seem to make much sense?? Wrt. to hardware options, does it make any difference which VM software we use (VMWare, MS, Virtualbox, ... ?) (We're using Windows exclusively for our builds.) Regarding budget: We have a normal small company (20 developers) budget for this. ;-) That is, if it's going to cost a few k$ it's going to cost. If it's free - the better. I strongly prefer solutions where there's no multi-k$ maintenance costs per year.

  Read the article

• I can't delete a directory inside a junctioned directory

  - by Fredy Muñoz

  So this is the deal. A couple of days ago I moved my profile folder C:\Documents and Settings\fmunoz to a different drive D:\fmunoz. Today, I created a directory in my desktop using the point-and-click method: Right-click on an empty space in the desktop Select New Select Folder Leave the default name New Folder and press Enter I tried to delete the folder using the point-and-click method: Right-click the New Folder directory Select Delete After five seconds, I got the following message: --------------------------- Error Deleting File or Folder --------------------------- Cannot delete New Folder: Access is denied. Make sure the disk is not full or write-protected and that the file is not currently in use. --------------------------- Initially I thought that there must be some sort of indexing services locking the directory so I got a list of open files using the TuneUp Process Manager tool but the New Folder directory wasn't there. I double-clicked My Computer, navigated to the desktop directory C:\Documents and Settings\fmunoz\Destkop, tried to delete the New Folder directory using the same point-and-click method described above and got exactly the same message at the same amount of time. In the same window, I navigated to the actual location of the desktop directory D:\fmunoz\Desktop, tried to delete the New Folder directory and this time it worked. I thought that this behavior was due to some special treatment that Windows gives to the desktop or the profile directories so I tried doing the same thing with a different set of directories: Created a folder D:\dummy Created a junction C:\dummy pointing to D:\dummy Created a New Folder directory in C:\dummy Tried to delete New Folder from C:\dummy. Didn't work. Tried to delete New Folder from D:\dummy. It worked. I tried creating the folder in the actual directory rather than the junction directory: Created a New Folder directory in D:\dummy Tried to delete New Folder from C:\dummy. Didn't work. Tried to delete New Folder from D:\dummy. It worked. I also tried using the Delete button instead of using the Delete option of the context menu but it didn't work. When using the Shift+Delete sequence, it works. It also works by using the rd command in the console, but in both cases the deleted directory doesn't goes to the Recycle Bin, which is my intention when using the Delete context menu option or the Delete button.

  Read the article

• How to store data on a machine whose power gets cut at random

  - by Sevas

  I have a virtual machine (Debian) running on a physical machine host. The virtual machine acts as a buffer for data that it frequently receives over the local network (the period for this data is 0.5s, so a fairly high throughput). Any data received is stored on the virtual machine and repeatedly forwarded to an external server over UDP. Once the external server acknowledges (over UDP) that it has received a data packet, the original data is deleted from the virtual machine and not sent to the external server again. The internet connection that connects the VM and the external server is unreliable, meaning it could be down for days at a time. The physical machine that hosts the VM gets its power cut several times per day at random. There is no way to tell when this is about to happen and it is not possible to add a UPS, a battery, or a similar solution to the system. Originally, the data was stored on a file-based HSQLDB database on the virtual machine. However, the frequent power cuts eventually cause the database script file to become corrupted (not at the file system level, i.e. it is readable, but HSQLDB can't make sense of it), which leads to my question: How should data be stored in an environment where power cuts can and do happen frequently? One option I can think of is using flat files, saving each packet of data as a file on the file system. This way if a file is corrupted due to loss of power, it can be ignored and the rest of the data remains intact. This poses a few issues however, mainly related to the amount of data likely being stored on the virtual machine. At 0.5s between each piece of data, 1,728,000 files will be generated in 10 days. This at least means using a file system with an increased number of inodes to store this data (the current file system setup ran out of inodes at ~250,000 messages and 30% disk space used). Also, it is hard (not impossible) to manage. Are there any other options? Are there database engines that run on Debian that would not get corrupted by power cuts? Also, what file system should be used for this? ext3 is what is used at the moment. The software that runs on the virtual machine is written using Java 6, so hopefully the solution would not be incompatible.

  Read the article

• Tips for maximizing Nginx requests/sec?

  - by linkedlinked

  I'm building an analytics package, and project requirements state that I need to support 1 billion hits per day. Yep, "billion". In other words, no less than 12,000 hits per second sustained, and preferably some room to burst. I know I'll need multiple servers for this, but I'm trying to get maximum performance out of each node before "throwing more hardware at it". Right now, I have the hits-tracking portion completed, and well optimized. I pretty much just save the requests straight into Redis (for later processing with Hadoop). The application is Python/Django with a gunicorn for the gateway. My 2GB Ubuntu 10.04 Rackspace server (not a production machine) can serve about 1200 static files per second (benchmarked using Apache AB against a single static asset). To compare, if I swap out the static file link with my tracking link, I still get about 600 requests per second -- I think this means my tracker is well optimized, because it's only a factor of 2 slower than serving static assets. However, when I benchmark with millions of hits, I notice a few things -- No disk usage -- this is expected, because I've turned off all Nginx logs, and my custom code doesn't do anything but save the request details into Redis. Non-constant memory usage -- Presumably due to Redis' memory managing, my memory usage will gradually climb up and then drop back down, but it's never once been my bottleneck. System load hovers around 2-4, the system is still responsive during even my heaviest benchmarks, and I can still manually view http://mysite.com/tracking/pixel with little visible delay while my (other) server performs 600 requests per second. If I run a short test, say 50,000 hits (takes about 2m), I get a steady, reliable 600 requests per second. If I run a longer test (tried up to 3.5m so far), my r/s degrades to about 250. My questions -- a. Does it look like I'm maxing out this server yet? Is 1,200/s static files nginx performance comparable to what others have experienced? b. Are there common nginx tunings for such high-volume applications? I have worker threads set to 64, and gunicorn worker threads set to 8, but tweaking these values doesn't seem to help or harm me much. c. Are there any linux-level settings that could be limiting my incoming connections? d. What could cause my performance to degrade to 250r/s on long-running tests? Again, the memory is not maxing out during these tests, and HDD use is nil. Thanks in advance, all :)

  Read the article

• Possible HDD malfunction. Need help in diagnosing

  - by Protheus

  Today when using my PC as I did for almost 4 years I experienced the following: during opening new tab in Opera browser screen froze. Music (AIMP 3) continued to play for about 5 minutes and then stopped too. I tried Ctrl+Alt+Del, but win7 lock screen didn't appear. Caps\Scroll or Num locks didn't switch diodes on keyboard. I rebooted my PC and saw that BIOS suggests me to enter it's settings or load by default. I chose default. It don't see proper boot device (old faitful "insert proper boot" something). After second reboot it said that there is no ExpressGate installed (which i turned off in BIOS years ago). I went into BIOS setting to turn off ExpressGate and see configs: time was not set off, all hard drives present, temp and O.C. settings are nominal (no O.C.) I've inserted my Win7 install disk to try recovery. It did load awfully long (about few minutes) and didn't see current installation. PC was utilized in 24/7 mode for almost all these years. Hardware configuration: ASUS P5Q WS Core 2 Quad Q9300 (2.5GHz no O.C.) MSI geForce GTX 460 4x2 Gb GeIL EVO 2 (AFAIR) Seagate something 750Gb (4 years as system HDD 24/7) WD 1Tb (for random stuff, 5 y.o.) Hitachi 500Gb (for even more random stuff, 6 y.o.) NEC DVDRW (ALL DISKS ARE SATA) Cooler Master Silent Pro 700W Software: Windows 7 AND Kubuntu on the same drive with GRUB loader. Sorry I can't remember HDDs and can't see them right now, but I think their models aren't relevant anyway. My idea is that due to some system error or hard drive glitch i've wrecked my primary HDD's MBR. Nevertheless I don't exclude the possibility of other failure. May it's be that motherboard or it's SATA controller? Doubt it, because all drives are seen in BIOS and I could load from DVD. Maybe GRUB got bugged somehow, although I don't see how it's possible from Windows. But I did install KUbuntu from Windows (i wasn't myself then), maybe GRUB did write itself in some windows partition and got rewriteen in process? Right now I am at work with my flash drive with me and I need some advice how to fix MBR or to hear if it's not MBR. I'm going to buy new HDD (Hitachi 7k2000) because I think that my current HDD is compromised and it's unsafe to use it as system drive, especially 24/7.

  Read the article

• How does the Cloud compare to Colocation? And development too

  - by David

  Currently I/we run a SaaS web application where each subscriber has their own physical instance of the application in addition to their own database. The setup has each web application instance deployed on two different IIS boxes both for load-balancing and redundancy (the machines have their Windows Update install times 12 hours apart, for example). Databases are mirrored on two different SQL Server 2012 machines with AlwaysOn for uptime. I don't make use of SQL Server clustering (as it doesn't provide storage-level failover: we don't have a shared storage box). Because it's a Windows setup it means there are two Domain Controllers (we cheat: they're both Mac Minis, 17W each, which keeps our colo power costs low). Finally there's also an Exchange server (Mailbox, Hub Transport and Client Access). One of the SQL Servers also doubles-up as an Exchange Hub Transport. Running costs are about $700 a month for our quarter-rack colocation (which includes power and peering/transfer), then there's about $150 a month for SPLA licensing, so $850 a month in total. Then there's the hard-to-quantify cost of administration, but I reckon I spend a couple of hours a week checking-in on the servers: reviewing event logs, etc. I keep getting bombarded by ads and manufactured news stories about how great "the cloud" is. Back in 2008 when the cloud was taking off I was reading up about the proper "cloud" services like Google AppEngine, where you write in Python against Google's API and that's how they scale your application across servers and also use their database provider for scaling storage. Simple enough to understand. Then came along Amazon, and I understand how Amazon Storage works, but I'm not sure how Amazon Compute works: web application pages don't take much CPU time to compute, how do you even quantify usage anyway? Finally, RackSpace gets in the act and now I'm really confused. RackSpace advertise "Cloud" SQL Server 2012 available for about "$0.70 per hour", going by how they advertise it I thought the "hour" meant the sum of CPU time, IO blocking time, maybe time spent transferring data, so for a low-intensity application that works out pretty cheap then? Nope. I went on to a Sales Chat window and spoke to one of their advisors. They told me the $0.70/hour was actually for every hour the SQL Server is running... but who wants a SQL Server for only a few hours? You're going to need it available 24 hours a day for months on end. $0.70 * 24 * 31 works out at $520 a month, which is rediculously expensive for SQL Server. An SPLA license for SQL Server is only $50 a month or so. That $520 a month does not include "fanatical support", and you also need to stack on top the costs of the host Windows server instance too. From what I can tell, Rackspace's "Cloud" products seem like like an cynical rebranding of an overpriced VPS service, but priced by the hour. I have the same confusion about Windows Azure which uses similar terms to describe the products available, but I think that's because Azure offers both traditional shared webhosting in addition to their own APIs you can target for scalable applications.

  Read the article

• Achieving A 1600 x 900 Resolution For (Guest OS) Ubuntu Under (Host OS) Windows 7

  - by panamack

  I am running Ubuntu 11.10 as a guest OS using VirtualBox 4.1.16 installed on Windows 7 Ultimate. On my laptop I'd like to be able to run Ubuntu in full screen mode at 1600 x 900. I only have options within the virtual machine to select 4:3 display settings such as 1600 x 1200, 1440 x 1050 etc. I have guest additions installed. At the windows command prompt, I tried typing: VBoxManage setextradata "Virtual Ubuntu Coursera ESSAAS" "CustomVideoMode1" "1600x900x16" This didn't work, still no 1600 x 900 res available in Ubuntu. I tried this having read the following section of the VirtualBox help (this also says something about a 'video mode hint feature' not sure what this means): 9.7. Advanced display configuration 9.7.1. Custom VESA resolutions Apart from the standard VESA resolutions, the VirtualBox VESA BIOS allows you to add up to 16 custom video modes which will be reported to the guest operating system. When using Windows guests with the VirtualBox Guest Additions, a custom graphics driver will be used instead of the fallback VESA solution so this information does not apply. Additional video modes can be configured for each VM using the extra data facility. The extra data key is called CustomVideoMode with x being a number from 1 to 16. Please note that modes will be read from 1 until either the following number is not defined or 16 is reached. The following example adds a video mode that corresponds to the native display resolution of many notebook computers: VBoxManage setextradata "VM name" "CustomVideoMode1" "1400x1050x16" The VESA mode IDs for custom video modes start at 0x160. In order to use the above defined custom video mode, the following command line has be supplied to Linux: vga = 0x200 | 0x160 vga = 864 For guest operating systems with VirtualBox Guest Additions, a custom video mode can be set using the video mode hint feature. UPDATE 02.06.12 I've just tried creating a new virtual machine using the same original disk image I had been given. This had Guest Additions v 4.1.6 installed and provided me with the 1600 x 900 full screen display I want. It's after I then install Guest Additions v 4.1.16 (the version included with my VirtualBox installation) that my only choices are 4:3 displays e.g. 1600 x 1200. Seems this is the cause.

  Read the article

• MySQL performance over a (local) network much slower than I would expect

  - by user15241

  MySQL queries in my production environment are taking much longer than I would expect them too. The site in question is a fairly large Drupal site, with many modules installed. The webserver (Nginx) and database server (mysql) are hosted on separated machines, connected by a 100mbps LAN connection (hosted by Rackspace). I have the exact same site running on my laptop for development. Obviously, on my laptop, the webserver and database server are on the same box. Here are the results of my database query times: Production: Executed 291 queries in 320.33 milliseconds. (homepage) Executed 517 queries in 999.81 milliseconds. (content page) Development: Executed 316 queries in 46.28 milliseconds. (homepage) Executed 586 queries in 79.09 milliseconds. (content page) As can clearly be seen from these results, the time involved with querying the MySQL database is much shorter on my laptop, where the MySQL server is running on the same database as the web server. Why is this?! One factor must be the network latency. On average, a round trip from from the webserver to the database server takes 0.16ms (shown by ping). That must be added to every singe MySQL query. So, taking the content page example above, where there are 517 queries executed. Network latency alone will add 82ms to the total query time. However, that doesn't account for the difference I am seeing (79ms on my laptop vs 999ms on the production boxes). What other factors should I be looking at? I had thought about upgrading the NIC to a gigabit connection, but clearly there is something else involved. I have run the MySQL performance tuning script from http://www.day32.com/MySQL/ and it tells me that my database server is configured well (better than my laptop apparently). The only problem reported is "Of 4394 temp tables, 48% were created on disk". This is true in both environments and in the production environment I have even tried increasing max_heap_table_size and Current tmp_table_size to 1GB, with no change (I think this is because I have some BLOB and TEXT columns).

  Read the article

• Concerning persistence size in the Linux Live Creator

  - by user63085

  Message : Hello everyone! I have ,for the last several months, used the Linux Live USB Creator which it is a very useful app to make portable OS on to flash drives. I mostly use this application to test and try out new OS's as they are released, before I decide to make a hard disk installatio on to the computer. In many cases, the application developers will allow the “persistence” feature in the flash-drive-installed OS, which is just another way of saying that after multiple boot-ups and shutdowns, all the changes made to the OS will be saved in the flash-drive. But I have a question about the limit of the Persistence size in Linux Live USB Creator (currently version 2.6). I install Super OS 10 on to a partition on my external drive which has 30 GB. I wanted to reserve 10 GB for the persistence so that I can install more applications and space will not run out as I update the installed applications or when I do system updates. But why is it that only 3950 MB can be put for persistence? It would be great if, when desired, as much more persistence space could be set aside so that the space will not run out soon. Also, as I have installed the OS on a 30 GB drive, I tried to see how much space is left. But it seems only the remaining of the Persistence space is displayed when I click on the File System folder. For example, after I have just installed it now, there is 3.5 GB of free space. Where can I access the remaining 26 GB or so drive space which is in the same drive? How do I access it Sir?? It would be helpful if any one could explain and help me with this. Most importantly, it would be a big relief if the persistence can be somehow expanded by a work-around so that I can continue using my SuperOS 10.04 (now heavily customized) OS, which unfortunately has just over 576 MB of space left now, after I removed OpenOffice.org and installed the Libre Office earlier today. This is what remains from the maximum allowable 3950 MB of space for persistence at set-up. Thanks in advance!

  Read the article

• vmdk to live cd - VMware vmxnet virtual NIC driver Kernel panic

  - by ronalchn

  Task I am trying to convert a virtual machine to a live CD. Specifically, the virtual machine I am trying to convert is the IOI 2013 Competition Environment. In this task, I am aided by a guide Converting a virtual disk image: VDI or VMDK to an ISO you can distribute. Symptoms However, after getting through all the instructions, the live CD causes a kernel panic on boot on bare metal. In particular, the screen shows: [0.737348] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.737503] sr 3:0:0:0: >Attached scsi CD-ROM sr0 [0.737638] sr 3:0:0:0: >Attached scsi generic sg2 type 5 [0.737771] Freeing unused kernel memory: 756k freed [0.738093] Write protecting the kernel text: 5960k [0.738155] Write protecting the kernel read-only data: 2424k [0.738224] NX-protecting the kernel data: 4280k Loading, please wait... [0.752252] udevd[100]: starting version 175 [0.768708] VMware vmxnet3 virtual NIC driver - version 1.1.29.0-k-NAPI [0.781204] VMware PVSCSI driver - version 1.0.2.0-k [0.789555] VMware vmxnet virtual NIC driver [0.799356] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [0.799356] [0.799472] Pid: 1, comm: init Tainted: G 0 3.5.0-17-generic #28-Ubuntu [0.799549] Call Trace: [0.799603] [<c15bf0ec>] panic+0x81/0x17b [0.799654] [<c104a6a5>] do_exit+0x745/0x7a0 [0.799707] [<c104a9a4>] do_group_exit+0x34/0xa0 [0.799760] [<c104aa28>] sys_exit_group+0x18/0x20 [0.799813] [<c15cff5f>] sysenter_do_call+0x12/0x28 Possible problem I suspect that the problem is the VMware vmxnet virtual NIC driver - however, I do not know how I can uninstall it, and possibly install one for a bare metal machine. If anyone knows which packages needs installing/uninstalling at the .rootfs/ chroot directory stage, please let me know. Details on procedure Do note that after importing the .ova file into Virtualbox, the virtual machine is stored as a .vmdk file already, and not a .vdi file. I would like to point out some results of the procedure followed in case of any questions. This is after extracting the filesystem from the .raw file to the .rootfs/ directory mentioned in the blog. I changed the filesystem table as mentioned in the blog, then looked at the possible "kernel optimized for virtualization". However, I found that linux-image-generic was already installed. Also, when running the command dpkg-query --showformat='${Package}\n' -W 'vmware-tools*' (or dpkg-query --showformat='${Package}\n' -W '*-virtual'), no packages were found. Thus, I did not find any virtualization specific packages. I proceeded to generate the iso following the steps in the blog, and burned it to a DVD.

  Read the article

• SQL Express 2008 R2 on Amazon EC2 instance: tons of free memory, poor performance

  - by gravyface

  The old SQL Express 2005 was running on a low-end single Xeon CPU Dell server, RAID 5 7200 disks, 2 GB RAM (SBS 2003). I have not done any baseline measurements on the old physical server, but the Web app is used by half a dozen people (maybe 2 concurrently), so I figured "how bad can an Amazon EC2 instance be?". It's pretty horrible: a difference of 8 seconds of load time on one screen. First of all, I'm not a SQL guru, but here's what I've tried: Had a Small Instance, now running a c1.medium (High Cpu Medium) Windows 2008 32-bit R2 EBS-backed instance running IIS 7.5 and SQL Express 2008 R2. No noticeable improvement. Changed Page File from fixed 256 to Automatic. Setup a Striped Mirror from within Disk Management with two attached 1 GB EBS volumes. Moved database and transaction log, left everything else on the boot EBS volume. No noticeable change. Looked at memory, ~1000 MB of physical memory free (1.7 GB total). Changed SQL instance to use a minimum of 1024 RAM; restarted server, no change in memory usage. SQL still only using ~28MB of RAM(!). So I'm thinking: this database is tiny (28MB), why isn't the whole thing cached in RAM? Surely that would speed up performance. The transaction log is 241 MB. Seems kind of large in comparison -- has this not been committed? Is it a cause of performance degradation? I recall something about Recovery Models and log sizes somewhere in my travels, but not positive. Another thing: the old server was running SQL Express 2005. Not sure if that has any impact, but I tried changing the compatibility level from SQL 2000 to 2008, but that had no effect. Anyways, what else can I try here? Seems ridiculous to throw more virtual hardware at this thing. I know I/O is going to be rough on EBS volumes, but surely others are successfully running small .NET/SQL apps on reasonably priced instances?

  Read the article

• How can I minimize the amount my router slows down my Internet connection speed?

  - by Lord Torgamus

  Background I'm working with what I assume is a pretty common Internet setup: a cable modem, a wireless router and a few Internet-connected devices. Lately, I've started being more demanding on my Internet connection, and noticed that using my router slows down my download speeds considerably. I just kind of dealt with it until Zune Marketplace on the Xbox 360 told me that a movie was going to take well over ten hours to download, and I just didn't want to wait that long. Good little scientist that I am, I tried to reduce the problem down to one variable. The test As a control, I turned off all the devices in the house that use wireless Internet, and unplugged all the wired devices except for the Xbox. I also power-cycled both the modem and the router. I then tried to download the movie again, and was told that it would still take over ten hours. Next, I unplugged the router, and connected the Xbox directly to the modem. The movie downloaded in just over one hour. As far as I can tell, this means that my ISP, other cable users near me, the remote servers, anything wireless-related and my machines' disk speeds can't be at fault. A similar experiment that replaced the Xbox with a wired laptop produced similar results. To me, this says "the router is responsible for things taking around ten times longer to download." My question I'd still prefer to use the router for a few reasons: it's a pain to connect and disconnect everything every time there's a big file to download direct connection to the modem isn't good for security only one machine can be connected directly to the modem at a time What can I do to have fast connection speeds while still using the router? I don't mind turning other machines off, as long as I don't have to mess with power and ethernet cables. EDIT : After asking this followup question and then this one, I installed dd-wrt on my router, and I seem to be getting higher and more consistent speeds. Perhaps more importantly, my memory use is fairly constant. I know this isn't an answer — which is why I'm not posting it as an answer — but it is how I resolved the situation, and hopefully it'll be helpful for someone.

  Read the article

• What server setup for a small web development company? [closed]

  - by Giordano

  I co-own a company with a friend of mine and we have decided to buy a new server to support our business (our current server is an Asus EEE Box, working great but too limited :) ). I should mention that we are web developers but occasionally we do small-office sys admin. Thus, 99% of time we work on GNU/Linux (mainly Ubuntu) but from time to time we need to setup a Windows environment to assist some customers (e.g. setup a temporary SQL Server 2008). Our requirements: Low budget: we don't want the cheapest solution out there but we can't afford to spend too much. Budget could be ~1000-1500€ (before VAT) Robustness: we would like to setup a RAID array and maybe have an external disk where we can store backups Virtualization: we need to be able to setup few servers for development. The scenario is something like this (~8 appliances running in parallel): Redmine + GIT server Bacula server FTP server 3-4 virtual appliances that could be set up on demand to test our applications or support a customer. The appliances could be: LAMP, Tomcat+PostgreSQL, SQL Server Support: if something breaks down it shouldn't be too difficult to find a replacement. Now, given the main requirements, there are some doubts we need to clarify: Do you suggest to buy a prepackaged solution (for example a customized Dell PowerEdge T110 or T310) or to assemble the server by ourselves (buy the separate components)? What RAID configuration do you suggest? I was thinking of RAID1 (probably cheaper) or RAID5. should we buy a hardware RAID controller or is it ok to use a software RAID (mdadm)? In case, which controller do you suggest? What processor do you suggest (Intel Xeon, i3, i5, i7, AMD)? How much RAM? (I was thinking at least 8GB, ~1GB per appliance) What virtualization software do you recommend? VMWare seems to be the best choice, but what about XEN or KVM? We don't want to buy licenses at the moment so we would like to consider only free options. What OS do you recommend? We know Ubuntu, Debian, Gentoo very well (we would like to use Ubuntu Server), however it seems a lot of people goes for CentOS. Thanks in advance if you can help us with this! It's our first "serious" server so many doubts popped up :) Please feel free to add further recommendations if you have some to share ;) Have a nice day

  Read the article

• JPA exception: Object: ... is not a known entity type.

  - by Toto

  I'm new to JPA and I'm having problems with the autogeneration of primary key values. I have the following entity: package jpatest.entities; import java.io.Serializable; import javax.persistence.Entity; import javax.persistence.GeneratedValue; import javax.persistence.GenerationType; import javax.persistence.Id; @Entity public class MyEntity implements Serializable { private static final long serialVersionUID = 1L; @Id @GeneratedValue(strategy = GenerationType.AUTO) private Long id; public Long getId() { return id; } public void setId(Long id) { this.id = id; } private String someProperty; public String getSomeProperty() { return someProperty; } public void setSomeProperty(String someProperty) { this.someProperty = someProperty; } public MyEntity() { } public MyEntity(String someProperty) { this.someProperty = someProperty; } @Override public String toString() { return "jpatest.entities.MyEntity[id=" + id + "]"; } } and the following main method in other class: public static void main(String[] args) { EntityManagerFactory emf = Persistence.createEntityManagerFactory("JPATestPU"); EntityManager em = emf.createEntityManager(); em.getTransaction().begin(); MyEntity e = new MyEntity("some value"); em.persist(e); /* (exception thrown here) */ em.getTransaction().commit(); em.close(); emf.close(); } This is my persistence unit: <?xml version="1.0" encoding="UTF-8"?> <persistence version="1.0" xmlns="http://java.sun.com/xml/ns/persistence" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/persistence http://java.sun.com/xml/ns/persistence/persistence_1_0.xsd"> <persistence-unit name="JPATestPU" transaction-type="RESOURCE_LOCAL"> <provider>oracle.toplink.essentials.PersistenceProvider</provider> <class>jpatest.entities.MyEntity</class> <properties> <property name="toplink.jdbc.user" value="..."/> <property name="toplink.jdbc.password" value="..."/> <property name="toplink.jdbc.url" value="jdbc:mysql://localhost:3306/jpatest"/> <property name="toplink.jdbc.driver" value="com.mysql.jdbc.Driver"/> <property name="toplink.ddl-generation" value="create-tables"/> </properties> </persistence-unit> </persistence> When I execute the program I get the following exception in the line marked with the proper comment: Exception in thread "main" java.lang.IllegalArgumentException: Object: jpatest.entities.MyEntity[id=null] is not a known entity type. at oracle.toplink.essentials.internal.sessions.UnitOfWorkImpl.registerNewObjectForPersist(UnitOfWorkImpl.java:3212) at oracle.toplink.essentials.internal.ejb.cmp3.base.EntityManagerImpl.persist(EntityManagerImpl.java:205) at jpatest.Main.main(Main.java:...) What am I missing?

  Read the article

• Routing audio to Bluetooth Headset (non-A2DP) on Android

  - by Jayesh

  I have a non-A2DP single ear BT headset (Plantronics 510) and would like to use it with my Android HTC Magic to listen to low quality audio like podcasts/audio books. After much googling I found that only phone call audio can be routed to the non-A2DP BT headsets. (I would like to know if you have found a ready solution to route all kinds of audio to non-A2DP BT headsets) So I figured, somehow programmatically I can channel the audio to the stream that carries phone call audio. This way I will fool the phone to carry my mp3 audio to my BT headset. I wrote following simple code. import android.content.*; import android.app.Activity; import android.os.Bundle; import android.media.*; import java.io.*; import android.util.Log; public class BTAudioActivity extends Activity { private static final String TAG = "BTAudioActivity"; private MediaPlayer mPlayer = null; private AudioManager amanager = null; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); amanager = (AudioManager) getSystemService(Context.AUDIO_SERVICE); amanager.setBluetoothScoOn(true); amanager.setMode(AudioManager.MODE_IN_CALL); mPlayer = new MediaPlayer(); try { mPlayer.setDataSource(new FileInputStream( "/sdcard/sample.mp3").getFD()); mPlayer.setAudioStreamType(AudioManager.STREAM_VOICE_CALL); mPlayer.prepare(); mPlayer.start(); } catch(Exception e) { Log.e(TAG, e.toString()); } } @Override public void onDestroy() { mPlayer.stop(); amanager.setMode(AudioManager.MODE_NORMAL); amanager.setBluetoothScoOn(false); super.onDestroy(); } } As you can see I tried combinations of various methods that I thought will fool the phone to believe my audio is a phone call: Using MediaPlayer's setAudioStreamType(STREAM_VOICE_CALL) using AudioManager's setBluetoothScoOn(true) using AudioManager's setMode(MODE_IN_CALL) But none of the above worked. If I remove the AudioManager calls in the above code, the audio plays from speaker and if I replace them as shown above then the audio stops coming from speakers, but it doesn't come through the BT headset. So this might be a partial success. I have checked that the BT headset works alright with phone calls. There must be a reason for Android not supporting this. But I can't let go of the feeling that it is not possible to programmatically reroute the audio. Any ideas? P.S. above code needs following permission <uses-permission android:name="android.permission.MODIFY_AUDIO_SETTINGS"/>

  Read the article

• SunTlsRsaPremasterSecret KeyGenerator not available

  - by Jill

  Hi, I encountered an error when my application tries to load a RSA Algorithm provider class from JAVA. The exception stack is as follow: javax.jms.JMSException: RSA premaster secret error at org.apache.activemq.util.JMSExceptionSupport.create(JMSExceptionSupport.java:49) at org.apache.activemq.ActiveMQConnection.syncSendPacket(ActiveMQConnection.java:1255) at org.apache.activemq.ActiveMQConnection.ensureConnectionInfoSent(ActiveMQConnection.java:1350) at org.apache.activemq.ActiveMQConnection.setClientID(ActiveMQConnection.java:388) at com.trendmicro.tmsm.TMSMAgent.open(TMSMAgent.java:63) Caused by: javax.net.ssl.SSLKeyException: RSA premaster secret error at com.sun.net.ssl.internal.ssl.RSAClientKeyExchange.<init>(RSAClientKeyExchange.java:97) at com.sun.net.ssl.internal.ssl.ClientHandshaker.serverHelloDone(ClientHandshaker.java:634) at com.sun.net.ssl.internal.ssl.ClientHandshaker.processMessage(ClientHandshaker.java:226) at com.sun.net.ssl.internal.ssl.Handshaker.processLoop(Handshaker.java:516) at com.sun.net.ssl.internal.ssl.Handshaker.process_record(Handshaker.java:454) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readRecord(SSLSocketImpl.java:884) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.performInitialHandshake(SSLSocketImpl.java:1112) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.writeRecord(SSLSocketImpl.java:623) at com.sun.net.ssl.internal.ssl.AppOutputStream.write(AppOutputStream.java:59) at org.apache.activemq.transport.tcp.TcpBufferedOutputStream.flush(TcpBufferedOutputStream.java:115) at java.io.DataOutputStream.flush(DataOutputStream.java:106) at org.apache.activemq.transport.tcp.TcpTransport.oneway(TcpTransport.java:167) at org.apache.activemq.transport.InactivityMonitor.oneway(InactivityMonitor.java:237) at org.apache.activemq.transport.WireFormatNegotiator.sendWireFormat(WireFormatNegotiator.java:168) at org.apache.activemq.transport.WireFormatNegotiator.sendWireFormat(WireFormatNegotiator.java:84) at org.apache.activemq.transport.WireFormatNegotiator.start(WireFormatNegotiator.java:74) at org.apache.activemq.transport.failover.FailoverTransport.doReconnect(FailoverTransport.java:715) at org.apache.activemq.transport.failover.FailoverTransport$2.iterate(FailoverTransport.java:115) at org.apache.activemq.thread.PooledTaskRunner.runTask(PooledTaskRunner.java:122) at org.apache.activemq.thread.PooledTaskRunner$1.run(PooledTaskRunner.java:43) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) at java.lang.Thread.run(Thread.java:637) Caused by: java.security.NoSuchAlgorithmException: SunTlsRsaPremasterSecret KeyGenerator not available at javax.crypto.KeyGenerator.<init>(DashoA13*..) at javax.crypto.KeyGenerator.getInstance(DashoA13*..) at com.sun.net.ssl.internal.ssl.JsseJce.getKeyGenerator(JsseJce.java:223) at com.sun.net.ssl.internal.ssl.RSAClientKeyExchange.<init>(RSAClientKeyExchange.java:89) ... 22 more I've googled the error message and most of posts says it's because JVM cannot find sunjce_provider.jar. However, I can find the file in /Library/Java/Home/lib/ext folder. The platform is Mac OS X 10.6 and Java version is 1.6.0_17. My questions are: Why JVM does not search /Library/Java/Home/lib/ext for jar files? Can we change CLASSPATH or java.ext.dirs property by modify any config file? Any suggestion to solve this problem? Thanks in advance.

  Read the article

• How to send email from an EC2 instance using GoDaddy's SMTP server?

  - by Matt Greer

  SMTP is a whole new ballgame for me, but I am reading up on it. I am attempting to send email from my EC2 instance using GoDaddy's SMTP server. My domain name is registered through GoDaddy and I have 2 email accounts with them. I can successfully send the email from my dev box no problem. my web.config <system.net> <mailSettings> <smtp from="[email protected]" deliveryMethod="Network"> <network host="smtpout.secureserver.net" clientDomain="mydomain.com" port="25" userName="[email protected]" password="mypassword" defaultCredentials="false" /> </smtp> </mailSettings> </system.net> In my ASP.NET app: MailMessage mailMessage = new MailMessage("[email protected]", recipientEmail, emailSubject, body); mailMessage.IsBodyHtml = false; SmtpClient mailClient = new SmtpClient(); mailClient.Send(mailMessage); Very typical, simple use of System.Net.Mail.SmtpClient. The mail client is picking up the settings from my web.config as expected. From the EC2 instance, the same setup yields: System.Net.Mail.SmtpException: Failure sending mail. ---> System.IO.IOException: Unable to read data from the transport connection: net_io_connectionclosed. at System.Net.Mail.SmtpReplyReaderFactory.ProcessRead(Byte[] buffer, Int32 offset, Int32 read, Boolean readLine) at System.Net.Mail.SmtpReplyReaderFactory.ReadLines(SmtpReplyReader caller, Boolean oneLine) at System.Net.Mail.SmtpReplyReaderFactory.ReadLine(SmtpReplyReader caller) at System.Net.Mail.SmtpConnection.GetConnection(ServicePoint servicePoint) at System.Net.Mail.SmtpClient.Send(MailMessage message) --- End of inner exception stack trace --- I have searched high and low and not found anyone else attempting this. All GoDaddy smtp situations I have found involve people being hosted by GoDaddy using their relay server. Some more info: My EC2 instance is Windows Server 2008 with IIS 7. The app is running in .NET 4 I can successfully use Gmail's SMTP server on the EC2 instance by using their port, setting SmtpClient.EnableSsl to true, and sending the mail through a gmail account. But we want to send the email from an account on our domain. I have port 25 open on both the Windows firewall and Amazon's Security group based firewall. I have played with Wireshark and noticed my SMTP related traffic was talking to ports in the 5,000s, so out of desperation I opened them all up to no avail (then closed them back down) As far as I know my EC2 instance's IP address is not black listed by GoDaddy. I have a feeling I'm just missing something fundamental. I also have a feeling someone is going to recommend I use AuthSmtp or something similar, I'll agree, and have had wasted the past 6 hours :)

  Read the article

• Can't Deploy or Upload Large SSRS 2008 Report from VS or IE

  - by Bratch

  So far in this project I have two reports in VS2008/BIDS. The first one contains 1 tablix and is about 100k. The second one contains 3 tablixes (tablices?) and is about 257k. I can successfully deploy the smaller report from VS and I can upload it from the Report Manager in IE. I can view/run it from Report Manager and I can get to the Report Server (web service) URL from my browser just fine. Everything is done over HTTPS and there is nothing wrong with the certificates. With the larger report, the error I get in VS is "The operation has timed out" after about 100 seconds. The error when I upload from IE is "The underlying connection was closed: An unexpected error occurred on a send" after about 130 seconds. In the RSReportServer.config file I tried changing Authentication/EnableAuthPersistence from true to false and restarting the service, but still get the error. I have the key "SecureConnectionLevel" set to 2. Changing this to 0 and turning off SSL is not going to be an option. I added a registry key named "MaxRequestBytes" to HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\HTTP\Parameters and set it to 5242880 (5MB) and restarted the HTTP and SRS services as suggested in a forum post by Jin Chen of MSFT. I still cannot upload the larger report. This is on MS SQL 2008 and WS 2003. Below is part of a log file entry from ...\Reporting Services\LogFiles when I attempted to upload from IE. library!WindowsService_0!89c!02/10/2010-07:57:57:: i INFO: Call to CleanBatch() ends ui!ReportManager_0-1!438!02/10/2010-07:59:33:: e ERROR: The underlying connection was closed: An unexpected error occurred on a send. ui!ReportManager_0-1!438!02/10/2010-07:59:34:: e ERROR: HTTP status code -- 500 -------Details-------- System.Net.WebException: The underlying connection was closed: An unexpected error occurred on a send. --- System.IO.IOException: Unable to write data to the transport connection: An established connection was aborted by the software in your host machine. --- System.Net.Sockets.SocketException: An established connection was aborted by the software in your host machine at System.Net.Sockets.Socket.MultipleSend(BufferOffsetSize[] buffers, SocketFlags socketFlags) at System.Net.Sockets.NetworkStream.MultipleWrite(BufferOffsetSize[] buffers) --- End of inner exception stack trace --- ...

  Read the article

< Previous Page | 452 453 454 455 456 457 458 459 460 461 462 463  | Next Page >