Search Results

Search found 15646 results on 626 pages for 'port 80'.

Page 456/626 | < Previous Page | 452 453 454 455 456 457 458 459 460 461 462 463  | Next Page >

  • Baseline 2952-SFP normal?

    - by Atlas
    I just installed a 3com 2952-sfp, and I had its port #48 connected to another gigabit switch through a cat5e cable. Now when I look at the logs, I see the lines shown below: Mar 23 11:20:15:829 2010 MSTP Critical PFWD Instance 0's GigabitEthernet1/0/48 has been set to forwarding state! Mar 23 11:20:15:822 2010 IFNET Warning LINK UPDOWN GigabitEthernet1/0/48: link status is UP Mar 23 11:20:12:974 2010 IFNET Warning LINK UPDOWN GigabitEthernet1/0/48: link status is DOWN The above happens like dozens of times per day, is there something wrong with my setup?

    Read the article

  • DFS Replication only works in one direction

    - by depthless
    SERVER1 - SBS 2011 SERVER2 - Windows Server 2008r2 I'm using DFS-R. Changes work perfectly from 1 to 2 but nothing propagates from 2 to 1. When I attempt to run: dfsrdiag staticrpc /port:5001 /member:SERVER2 I get the error: [ERROR] Failed to connect to WMI services on computer: SERVER2.domain That command works just fine in the other direction. I've completely disabled the firewall on both ends. SERVER1 pings SERVER2 just fine. RPC Service is running on both servers. WMI Service is running on both servers.

    Read the article

  • Server with IIS and Apache - how to SSL encrypt Apache with IIS

    - by GAThrawn
    I have a Windows Server 2003 box already setup and working with IIS 6. IIS is set to serve a site out over both HTTP and HTTPS connections using default ports. For various reasons I need to set Apache up on the same server and it needs to serve its pages to end-users as SSL encrypted HTTPS pages. Neither IIS or Apache are (or are ever likely to be) particularly high traffic or high usage. The way I see it there are two possible ways this could be done. Either export the SSL cert from IIS,set it up in Apache and get Apache to server the HTTPS connections itself over a non-default port. Or use IIS to proxy Apache in some way over it's existing SSL security. What is going to end up easiest to setup, configure, maintain and run? Which is going to work best? Has anyone done this sort of thing before? Any tips or things to look out for?

    Read the article

  • Apache Tomcat Server failure

    - by Kenneth Ordona
    I'm trying to set up Apache Tomcat 6 with SSL and once I edited the server.xml file to include the following definitions the server started to fail as soon as I hit startup.bat: <-- Define a SSL Coyote HTTP/1.1 Connector on port 8443 -- < Connector protocol="org.apache.coyote.http11.Http11Protocol" port="8445" maxThreads="200" scheme="https" secure="true" SSLEnabled="true" keystoreFile="${user.home}/.tomcat" keystorePass="pnnlpw" clientAuth="false" sslProtocol="TLS"/ The logs that I have are as follows: Jul 05, 2012 1:52:15 PM org.apache.catalina.core.AprLifecycleListener init INFO: The APR based Apache Tomcat Native library which allows optimal performance in production environments was not found on the java.library.path: C:\Program Files\Java\jdk1.7.0_05\bin;C:\WINDOWS\Sun\Java\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;. Jul 05, 2012 1:52:15 PM org.apache.tomcat.util.digester.Digester fatalError SEVERE: Parse Fatal Error at line 91 column 2: The content of elements must consist of well-formed character data or markup. org.xml.sax.SAXParseException; systemId: file://C/tomcat6/conf/server.xml; lineNumber: 91; columnNumber: 2; The content of elements must consist of well-formed character data or markup. at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.createSAXParseException(ErrorHandlerWrapper.java:198) at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.fatalError(ErrorHandlerWrapper.java:177) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:441) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:368) at com.sun.org.apache.xerces.internal.impl.XMLScanner.reportFatalError(XMLScanner.java:1388) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.startOfMarkup(XMLDocumentFragmentScannerImpl.java:2565) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.next(XMLDocumentFragmentScannerImpl.java:2663) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(XMLDocumentScannerImpl.java:607) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(XMLDocumentFragmentScannerImpl.java:488) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:835) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:764) at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(XMLParser.java:123) at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1210) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:568) at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642) at org.apache.catalina.startup.Catalina.load(Catalina.java:524) at org.apache.catalina.startup.Catalina.load(Catalina.java:562) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:261) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413) Jul 05, 2012 1:52:15 PM org.apache.catalina.startup.Catalina load WARNING: Catalina.start using conf/server.xml: org.xml.sax.SAXParseException; systemId: file://C/tomcat6/conf/server.xml; lineNumber: 91; columnNumber: 2; The content of elements must consist of well-formed character data or markup. at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1236) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:568) at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642) at org.apache.catalina.startup.Catalina.load(Catalina.java:524) at org.apache.catalina.startup.Catalina.load(Catalina.java:562) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:261) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413) Jul 05, 2012 1:52:15 PM org.apache.tomcat.util.digester.Digester fatalError SEVERE: Parse Fatal Error at line 91 column 2: The content of elements must consist of well-formed character data or markup. org.xml.sax.SAXParseException; systemId: file://C/tomcat6/conf/server.xml; lineNumber: 91; columnNumber: 2; The content of elements must consist of well-formed character data or markup. at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.createSAXParseException(ErrorHandlerWrapper.java:198) at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.fatalError(ErrorHandlerWrapper.java:177) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:441) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:368) at com.sun.org.apache.xerces.internal.impl.XMLScanner.reportFatalError(XMLScanner.java:1388) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.startOfMarkup(XMLDocumentFragmentScannerImpl.java:2565) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.next(XMLDocumentFragmentScannerImpl.java:2663) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(XMLDocumentScannerImpl.java:607) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(XMLDocumentFragmentScannerImpl.java:488) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:835) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:764) at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(XMLParser.java:123) at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1210) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:568) at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642) at org.apache.catalina.startup.Catalina.load(Catalina.java:524) at org.apache.catalina.startup.Catalina.start(Catalina.java:582) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:289) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:414) Jul 05, 2012 1:52:15 PM org.apache.catalina.startup.Catalina load WARNING: Catalina.start using conf/server.xml: org.xml.sax.SAXParseException; systemId: file://C/tomcat6/conf/server.xml; lineNumber: 91; columnNumber: 2; The content of elements must consist of well-formed character data or markup. at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1236) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:568) at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642) at org.apache.catalina.startup.Catalina.load(Catalina.java:524) at org.apache.catalina.startup.Catalina.start(Catalina.java:582) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:289) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:414) Jul 05, 2012 1:52:15 PM org.apache.catalina.startup.Catalina start SEVERE: Cannot start server. Server instance is not configured. Does anyone have an idea why this is happening? I believe it has to do with the configuration of my connector. I'm pretty new to this so any help would be much appreciated.

    Read the article

  • Intel Network Connection: This device cannot start. (Code 10)

    - by harryuser
    Hi, I have a Intel® Desktop Board DP55KG (see http://www.intel.com/products/desktop/motherboards/DP55KG/DP55KG-overview.htm), which has a Intel 82578DC Gigabit Network Connection on board. Additionally, I have a Intel PRO/1000 PT Dual Port Server Adapter in a PCI express slot and I am running Windows 7 Professional 32-bit. The problem I am having is that the Intel 82578DC Gigabit Network Connection will not start on boot with the following message: "This device cannot start. (Code 10)". Disabling and then enabling the device after boot makes the network connection work again without any problems, but as soon as I reboot the problem occurs again. Any suggestion how to fix this? I have seen this problem on another Intel S3420GP board as well in Windows 7 that is.

    Read the article

  • Share openVPN connection

    - by Douglas Gemignani
    Hello, Currently I have a server (dev tun) running openVPN and my WinXP client is able to connect to the server just fine. I have an ethernet device and I need to send data to a computer under the server's network, so since the device can't connect on its own I need to configurate my Windows XP to share its VPN connection. So, on my WinXP machine i have: Network Adapter #1 (ip 192.168.0.2 gw 192.168.0.1 with internet access). OpenVPN Connection (dhcp). Network Adapter #2 (crossover cable with device). Here is my client.ovpn cert gertec.crt key gertec.key client ns-cert-type server user nobody group nobody remote IP PORT ca ca.crt dev tun dev-node OpenVPN proto udp resolv-retry infinite nobind comp-lzo verb 3 I would appreciate any help.

    Read the article

  • Need help trouble shooting high CPU usage by PHP-fpm

    - by user432506
    There is a problem that is driving me crazy. After the day I tried to fix the CPU usage problem of my VPS, the CPU load has grown from 60% to 150%, and I have no idea what causes the problem. Please help me. I had installed a copy of mediawiki on a Linode 1024. The wiki is running on Niginx + PHP-fpm + MySql. The wiki doesn't have much traffic, only around 4000 requests/day, mostly from Google and Bing bots. It had been using around 60% (of total 400% on the Linode) of the CPU before. I thought it was a bit high, so two day ago, I was trying to fix the problem (not knowing what was waiting for me). I did nothing but added a new empty line to wiki's configure file, which would change the modified time of the configure file, and then all the cached page files would be set invalidated. I had done that before, and that would cause high CPU usage, but normally it would take only hours to let things back to normal again. Not this time, my CPU usage has been around 150% for more than two days. It is php-fpm using most of CPU reassures. Using 100% of three cores is not rare. I hadn't seen that before. There are other sites on the Linode, but it should be the wiki. Because if I offline the wiki, CPU usage will drop back to around 40% soon. The day I also duplicated php-fpm.conf, and opened it, but didn't changed it. I have no idea what I did wrong. I here ask for help to save myself from being crazy!!! It is php-fpm. Is there a way to find out what is it doing? I mean like which scripts are related and what function codes are running? top: top - 06:34:33 up 10 days, 4:23, 2 users, load average: 1.10, 1.24, 1.37 Tasks: 76 total, 4 running, 72 sleeping, 0 stopped, 0 zombie Cpu(s): 61.1%us, 3.1%sy, 0.0%ni, 32.8%id, 2.9%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 1028684k total, 945192k used, 83492k free, 89580k buffers Swap: 524284k total, 18084k used, 506200k free, 530380k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 26721 www-data 20 0 208m 54m 34m R 99 5.4 0:09.07 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26592 www-data 20 0 207m 45m 26m R 91 4.5 0:12.77 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26706 www-data 20 0 196m 43m 34m S 47 4.3 0:15.19 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26583 www-data 20 0 197m 45m 35m S 33 4.5 0:19.08 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26787 www-data 20 0 206m 36m 18m R 25 3.7 0:00.41 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26661 www-data 20 0 207m 46m 26m S 13 4.6 0:19.87 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 1971 mysql 20 0 155m 57m 3952 S 8 5.7 383:57.81 /usr/sbin/mysqld 242 root 20 0 0 0 0 S 1 0.0 0:51.36 [kworker/3:1] 5711 root 20 0 139m 95m 580 S 1 9.5 0:41.30 /usr/local/bin/memcached -d -u root -m 128 -p 11211 19463 root 20 0 190m 3984 1284 S 1 0.4 0:02.66 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 29100 www-data 20 0 10928 5540 820 S 1 0.5 4:49.05 nginx: worker process vmstat 30 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 16912 81456 90784 554172 0 0 4 6 3 2 11 1 87 1 0 0 16912 78036 91000 555356 0 0 38 34 1397 375 12 1 87 0 4 0 16912 31776 91528 557508 0 0 78 42 3197 487 45 1 52 1 1 0 16912 83356 91768 558576 0 0 35 56 2608 449 32 1 67 1 1 0 16912 81548 92040 559720 0 0 41 31 1243 432 8 1 91 1 2 0 16912 53056 92332 562744 0 0 105 33 2013 581 17 1 81 1 2 0 16912 73236 92552 564844 0 0 68 36 1968 615 16 1 82 1 0 0 16912 91612 92904 566676 0 0 69 35 1845 692 13 1 85 1 1 0 16912 71248 93180 568428 0 0 58 33 1952 604 15 1 82 1 1 0 16868 55952 93516 572660 1 0 144 42 1801 637 12 1 86 1 2 0 16868 48324 94416 577844 0 0 189 66 2058 702 17 1 80 2 1 0 16928 58644 94592 578184 0 2 160 49 2578 723 25 1 70 3 5 0 16928 22600 94980 580568 0 0 89 32 1496 361 13 0 85 1 0 0 16988 49256 94500 576396 0 2 41 37 1601 426 14 1 85 0 5 0 18084 24336 86032 502748 0 37 83 68 2989 562 42 1 56 0 1 0 18084 123604 86376 506996 0 0 118 41 2201 573 22 1 76 1 2 0 18084 126984 86752 508876 0 0 64 53 1620 490 13 1 85 1 2 0 18084 103104 87148 510768 0 0 71 37 2757 602 33 1 64 1

    Read the article

  • How to Bridge Two Ethernet Ports on Mac OS X

    - by Rabarberski
    How can I bridge two wired ethernet interfaces on Mac OS X (e.g. the current MacPro comes with two ethernet ports)? Googling turned up (e.g. this Apple forum post and this openvpn post) that this is fairly easy on Linux (using the brctl command) and under Windows (via Network Connections right-click Bridge Connections), but how is it done under Mac OS X? BTW: There also doesn't seem to be a macport for brctl ('port search brctl' didn't turn up any results) Note: I don't want to have 'internet sharing', which creates a new network (by handing out network addresses in a new range). I want to really 'bridge' two interfaces so to keep the same network subnet.

    Read the article

  • xrandr doesn’t detect display ports

    - by Psyhister
    I have a ThinkPad T510 laptop with Gentoo Linux installed on it and I can’t manage to get VGA and DisplayPort working. xrandr -q won’t show them, so I’m guessing, that there’s a problem with my kernel configuration, but I wasn’t able to find the options responsible for these ports. Here’s the output from xrandr -q: xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 175, current 1366 x 768, maximum 1366 x 768 default connected 1366x768+0+0 0mm x 0mm 1366x768 50.0* 51.0 52.0 1024x768 53.0 54.0 832x624 55.0 800x600 56.0 57.0 58.0 59.0 60.0 720x400 61.0 700x525 62.0 640x512 63.0 64.0 640x480 65.0 66.0 67.0 68.0 69.0 640x400 70.0 640x350 71.0 576x432 72.0 512x384 73.0 74.0 75.0 76.0 77.0 416x312 78.0 400x300 79.0 80.0 81.0 82.0 83.0 360x200 84.0 320x240 85.0 86.0 87.0 88.0 320x200 89.0 320x175 90.0 Can anyone help me figure out what the problem is and how to get the video connections to work?

    Read the article

  • Openswan + xl2tpd connections time out after a while

    - by Halfgaar
    I have a non-NATed Openswan+xl2tpd server (Ubuntu 12.04), to which I connect with a Windows 8 behind NAT. The client loses its connection after a while of doing nothing (between 30 and 60 minutes, but I didn't time it). The client doesn't have enabled that it should kill inactive connections. Nor does it ever go into sleep mode. I also tried setting the kill-after-time to 24 hours, but that didn't help. The NAT router behind which the client located is Debian Linux, and its router is a Cisco which connects us directly to the data center where the server is. None of our other connections, like SSH, get dropped with inactivity (because of cheap routers). I did however try turning on the keepalives in /etc/ipsec.conf: config setup (...snip...) nat_traversal=yes force_keepalive=yes keep_alive=10 but that didn't help. As you can see in the config later, dead peer detection's action is clear. That would be a first suggestion to fix, but I need clear, because people will be connecting from everwhere but the kitchen sink. Besides, as I said, in the test setup I have now, I can't see any device killing its connection. (edit: 'restart' also has the same effect) These are of one time it happened: Jul 18 16:18:06 host xl2tpd[1918]: Maximum retries exceeded for tunnel 49070. Closing. Jul 18 16:18:06 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 18359 Jul 18 16:18:06 host xl2tpd[1918]: Connection 4 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 16:18:11 host xl2tpd[1918]: Unable to deliver closing message for tunnel 49070. Destroying anyway. and these on another: Jul 18 17:44:39 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 xl2tpd[1918]: last message repeated 4 times Jul 18 17:44:43 host xl2tpd[1918]: Maximum retries exceeded for tunnel 10918. Closing. Jul 18 17:44:43 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 26338 Jul 18 17:44:43 host xl2tpd[1918]: Connection 6 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 17:44:44 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:48 xl2tpd[1918]: last message repeated 3 times Jul 18 17:44:48 host xl2tpd[1918]: Unable to deliver closing message for tunnel 10918. Destroying anyway. Jul 18 17:44:59 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:44:59 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:09 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:09 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:19 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:19 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:29 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:29 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:39 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:39 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:49 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:49 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Versions: Ubuntu 12.04 Openswan: 2.6.37-1 xl2tpd: 3.1+dfsg-1 kernel: 3.2.0-49-generic configs: /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:!10.152.2.0/24 oe=off protostack=netkey force_keepalive=yes keep_alive=10 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=2 rekey=no dpddelay=30 dpdtimeout=120 dpdaction=clear ikelifetime=8h keylife=1h type=transport left=%defaultroute leftprotoport=17/1701 right=%any rightprotoport=17/%any /etc/xl2tpd/xl2tpd.conf [global] ipsec saref = no [lns default] ip range = 10.152.2.2-10.152.2.254 local ip = 10.152.2.1 refuse chap = yes refuse pap = yes require authentication = yes ppp debug = no pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd: require-mschap-v2 refuse-mschap ms-dns 10.152.2.1 asyncmap 0 auth crtscts idle 1800 mtu 1200 mru 1200 lock hide-password local #debug name l2tpd proxyarp lcp-echo-interval 30 lcp-echo-failure 4

    Read the article

  • shrink size of ova file in virtualbox

    - by 130490868091234
    I've got an Ubuntu 64bit VM that I derived from a ~1GB ova file, I used it under VMware vSphere to install some more software on it and use the system against a few datasets that took some 2-3GB of space, but now that I deleted these big files, I was expecting that the newly generated ova file from it would also take about ~1.1GB of space, but instead is taking about 3GB. If I look at the details the .vmdk file in virtualbox, I see the following: Hart Disk: SATA Port 0 Type (Format): Normal (VMDK) Virtual Size: 8.00 GB Actual Size: 7.90 GB Details: Dynamically allocated storage Location: /somewhere/myVM-disk1.vmdk Attached To: myVM.virtualbox The size of the ova when I export this machine is ~3GB. Any ideas how I can shrink it?

    Read the article

  • website uses an invalid security certificate (Error code: ssl_error_bad_cert_domain)

    - by Walter Lockhart
    I am running IIS 7 on Windows Server 2008. I have two websites: www.website01.com www.website02.com I have an SSL Certificate for each website. When I access a secured page on www.website02.com I get the error: www.website02.com uses an invalid security certificate. The certificate is only valid for www.website01.com. (Error code: ssl_error_bad_cert_domain) I have googled this error and I understand that it is caused by the fact that I have bound both sites to the same IP Address / Port No. (443). However, I don't know what I need to do to remedy this situation. Would someone please help. Thanks in advance. Kind Regards Walter

    Read the article

  • https not working... binding set, certificate installed

    - by rksprst
    I've installed the certificate and set the https bindings. However, when I load the site on https it does not load. I've looked at all the settings but everything seems correct. I've restarted the site numerous times. The certificate is stored on the local computer under personal-certificates... I have the private key for the certificate. The port (443) is open. If I try https://localhost on the server, the site loads... but with a domain error (i.e. it's localhost and not thedomain.com). But https://thedomain.com doesn't load. I really don't know why the https url isn't loading... anyone have any ideas? Thanks!

    Read the article

  • Accessing Squid Proxy over internet

    - by user37074
    Hi, I recently finished installing Squid on a VPS I have in the US and its working fine locally (I verified by setting http_proxy variable and using lynx). I want to access this proxy over the internet (as an anonymizer) so that I can see how some ads show up for US traffic on my website. I have setup authentication so abuse is not a problem. However, I am not able to access the proxy over the internet. I have set the following rule in squid.conf http_access allow all Is this not possible to do what I want or I am missing something? The port 3128 is open in the firewall so that is not an issue. Squid is running on 0.0.0.0 Thanks

    Read the article

  • Accessing Squid Proxy over internet

    - by prateekdayal
    Hi, I recently finished installing Squid on a VPS I have in the US and its working fine locally (I verified by setting http_proxy variable and using lynx). I want to access this proxy over the internet (as an anonymizer) so that I can see how some ads show up for US traffic on my website. I have setup authentication so abuse is not a problem. However, I am not able to access the proxy over the internet. I have set the following rule in squid.conf http_access allow all Is this not possible to do what I want or I am missing something? The port 3128 is open in the firewall so that is not an issue. Squid is running on 0.0.0.0 Thanks Prateek

    Read the article

  • NAT: Exposing SQL Server 2008 Express to the internet

    - by Yves
    Hi, I have a Windows Server 2003 SP2 machine with SQL Server 2008 Express installed. I have my network configured with a NAT. Internal clients can access the instance of SQL Server without a problem. I would like to enable SQL Server to be accessible from anywhere on the the internet. I am not sure how to allow my NAT firewall to allow that. I tried adding the port 1443 to it but I still can't access it from a remote machine. How can you make a given SQL Server available to the WAN? Any help would be greatly appreciated. Thank you

    Read the article

  • Thomson TCM 420 internal firewall deactivation

    - by KB22
    Hi all, I'm having a really hard time with getting a box into active torrent mode. Windows firewall etc. is done, the actual problem seems to relate to the cable modem which is used to connect the box to the net. It's a Thomson TCM 420 which 'claims' to have an internal firewall. IMHO this internal FW keeps me from using the port I opened for torrenting. To cut it short: is there a way to disable that firewall? The web administration interface of the modem does not provide that option. thanks in advance K

    Read the article

  • Can't figure out error in Cisco ASA log "regular translation creation failed for icmp ..."

    - by Martijn Heemels
    Every few seconds our new Cisco ASA 5505 firewall is logging errors that I can't figure out with my limited Cisco experience. Severity Date Time Syslog ID Source IP Destination IP Description 3 Mar 25 2010 17:21:14 305006 8.8.8.8 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.8.8 (type 3, code 3) 3 Mar 25 2010 17:18:37 305006 8.8.4.4 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.4.4 (type 3, code 3) The logged inside IP is our internal DNS resolver, and the outside IP's are Google's public DNS servers. ICMP Type 3 Code 3 means "Port Unreachable" Our "outside" interface has a fixed IP and our "inside" interface is in the 10.10.0.0/16 subnet. The 'Inspect DNS' Service Policy is enabled, with the preset DNS inspection map. Furthermore there's an ACL that allows all inbound ICMP on the "outside" interface. I've spent hours trying to figure this one out, so any and all advice is welcome!

    Read the article

  • How to connect to a SOCKS Proxy from an iPhone/iPod Touch?

    - by GeneQ
    I like to surf securely and privately via a SOCKS proxy which I created via SSH tunneling, on the Mac. I used the SSH client on my Mac to achieve this. Then I thought, since the iPhone OS is essentially Mac OS, the same trick might work also on the iPhone. I managed to create a SSh tunnel on my iPhone via the Terminal (iPhone's Terminal). (Yes, it's jail-broken) ssh -D [port] [email protected] At this stage my iPhone is SOCKS proxy. However, there doesn't seem to be a way in the iPhone networking preference panel to specify a SOCKS proxy. Someone suggest creating a Proxy Auto-Contig (PAC) file to workaround this, but that sounds complicated. Any ideas how to make iPhone use it's own SOCKS proxy?

    Read the article

  • Packet loss rate with iperf and tcpdump

    - by stefita
    I tested a line for its link quality with iperf. The measured speed (UDP port 9005) was 96Mbps, which is fine, because both servers are connected with 100Mbps to the internet. On the other hand the datagram loss rate was shown to be 3.3-3.7%, which I found a little too much. Using a high-speed transfer protocol I recorded the packets on both sides with tcpdump. Than I calculated the packet loss - average 0.25%. Have anyone an explanation, where this big difference may be coming from? What is an acceptable packet loss in your opinion?

    Read the article

  • Using nginx + wordpress with all wordpress files in a subdirectory

    - by GorillaPatch
    My setup I am running nginx 0.7.67 on Debian Lenny as a webserver, not as a reverse proxy. I am using php5-fpm to handle my PHP requests, which works fine. My aim I would like to have a wordpress installation that is layed out as described here clean wordpress subversion installation. I would like to have a clean wordpress installation without cluttering my server root directory with all the wordpress files. That means that my wordpress installation would be in /wordpress and my themes and plugins inside /wordpress-content. The important point however is that if you navigate to my domain www.example.com then you would be taken directly to the wordpress blog, without having to specify the subdirectory where wordpress lives. I found a how-to at the nginx site installing wordpress but unfortunately this is for moving the entire wordpress directory instead of redirecting the traffic to it. I tried with the following configuration: example.conf in sites-available server { listen 80; server_name www.example.com; access_log /var/log/nginx/www.example.com.access.log main; root /var/www/example/htdocs; location / { try_files $uri $uri/ /wordpress/index.php?q=$uri&$args; } include /etc/nginx/includes/php5-wordpress.conf; include /etc/nginx/includes/deny.conf; } php5-wordpress.conf in includes location /wordpress { try_files $uri $uri/ /wordpress/index.php?q=$uri&$args; } location ~ \.php$ { fastcgi_split_path_info ^(/wordpress)(/.*)$; fastcgi_ignore_client_abort on; fastcgi_pass unix:/var/run/php5-fpm.socket; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } fastcgi_params fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; The problems I have is that when I go to the adress "http://www.example.com" I get a 403 error as I disabled directory listing. Instead I would like my wordpress to appear then. Also if I navigate to "http://www.example.com/wordpress" I get a "file not found" error. However if I comment out the fastcgi_split_path_info line in my php5-wordpress.conf at least the wordpress installation works inside /wordpress. I need help how to debug this behavior or where I can find more information. Thanks alot. Update: Added error log entry for the 403 error. in the error.log I get the following entry for the 403 error: 2010/12/11 07:54:24 [error] 9496#0: *1 directory index of "/var/www/example/htdocs/" is forbidden, client: XXX.XXX.XXX.XXX, server: www.example.com, request: "GET / HTTP/1.1", host: "www.example.com" Update 2: Added the nginx.conf below: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] $status ' '"$request" $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; index index.php index.html; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; }

    Read the article

  • Unix : `nc` on Ubuntu vs Redhat (netcat)

    - by bguiz
    How do I achieve the equivalent of nc -q in Redhat 5? Details? nc -q -1 local host ${PORT} ${CMD} In Ubuntu, nc may be use as above, with the -q option. See manpage. -q after EOF on stdin, wait the specified number of seconds and then quit. If seconds is negative, wait forever. However, this option is not available in Redhat 5. See manpage. (Note: The Red Hat website is horrible to search, if someone finds their manpage for nc, please edit this post or comment with the new link).

    Read the article

  • Looking for a manual/how-to for installing a Canon iRunner 210s network printer

    - by Ssvarc
    A client has a Canon iRunner210S and is complaining about slow print speeds. I've searched for a install manual online but came up empty. A call to Canon technical referred me to their dealer network for service, as as informing me that there isn't a manual available on their website. Anyone know how to install these and/or have a link to a manual? The current setup has the printers on a LAN Manager printer port instead of on straight IP ports. Is this normal for this printer? And what exactly are Lan Manager ports (based on my research, they appear to be a way to authenticate a connection)?

    Read the article

  • How to install a Canon iRunner 210s

    - by Ssvarc
    A client has a Canon iRunner210S and is complaining about slow print speeds. I've searched for a install manual online but came up empty. A call to Canon technical referred me to their dealer network for service, as as informing me that there isn't a manual available on their website. Anyone know how to install these and/or have a link to a manual? The current setup has the printers on a LAN Manager printer port instead of on straight IP ports. Is this normal for this printer? And what exactly are Lan Manager ports (based on my research, they appear to be a way to authenticate a connection)?

    Read the article

  • Unauthorized access error to html pages in IIS 7.0

    - by George2
    Hello everyone, I am using VSTS 2008 + C# + .Net 3.5 + IIS 7.0. I have created a new web site and put an html file into the directory. And when I use browse function in IIS manager to browse the html file, I met with the following error, any ideas what is wrong? BTW: I am very confused about unauthorized error since I run the worker process under administrator account. From the error message, I am confused why the logon method is anonymous and not using administrator account? HTTP Error 401.3 - Unauthorized You do not have permission to view this directory or page because of the access control list (ACL) configuration or encryption settings for this resource on the Web server. Module IIS Web Core Notification AuthenticateRequest Handler StaticFile Error Code 0x80070005 Requested URL http://localhost:80/a.html Physical Path C:\test\simplehosttest\a.html Logon Method Anonymous Logon User Anonymous thanks in advance, George

    Read the article

< Previous Page | 452 453 454 455 456 457 458 459 460 461 462 463  | Next Page >