Search Results

Search found 1477 results on 60 pages for 'daemon x'.

Page 46/60 | < Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >

• GRE Tunnel over IPsec with Loopback

  - by Alek

  I'm having a really hard time trying to estabilish a VPN connection using a GRE over IPsec tunnel. The problem is that it involves some sort of "loopback" connection which I don't understand -- let alone be able to configure --, and the only help I could find is related to configuring Cisco routers. My network is composed of a router and a single host running Debian Linux. My task is to create a GRE tunnel over an IPsec infrastructure, which is particularly intended to route multicast traffic between my network, which I am allowed to configure, and a remote network, for which I only bear a form containing some setup information (IP addresses and phase information for IPsec). For now it suffices to estabilish a communication between this single host and the remote network, but in the future it will be desirable for the traffic to be routed to other machines on my network. As I said this GRE tunnel involves a "loopback" connection which I have no idea of how to configure. From my previous understanding, a loopback connection is simply a local pseudo-device used mostly for testing purposes, but in this context it might be something more specific that I do not have the knowledge of. I have managed to properly estabilish the IPsec communication using racoon and ipsec-tools, and I believe I'm familiar with the creation of tunnels and addition of addresses to interfaces using ip, so the focus is on the GRE step. The worst part is that the remote peers do not respond to ping requests and the debugging of the general setup is very difficult due to the encrypted nature of the traffic. There are two pairs of IP addresses involved: one pair for the GRE tunnel peer-to-peer connection and one pair for the "loopback" part. There is also an IP range involved, which is supposed to be the final IP addresses for the hosts inside the VPN. My question is: how (or if) can this setup be done? Do I need some special software or another daemon, or does the Linux kernel handle every aspect of the GRE/IPsec tunneling? Please inform me if any extra information could be useful. Any help is greatly appreciated.

  Read the article

• how to cause linux system datetime to run faster than real world datetime?

  - by JamesThomasMoon1979

  Background I want to monitor a running linux system over several days. It's a custom gentoo build and with much custom software on board. This software has ongoing maintenance timers and cron scripts and other clock driven events. I need to verify these scheduled events are working. Problem Waiting for the system to step through daily and weekly activity is a long wait time. And modifying all clock-based timers on the system would be time consuming. Yet, I often want to test a system's end-to-end scheduled activities without waiting a week. Potential Solution Have the linux system under test appear to run through it's daily cycle of activity within just a few hours. My Question for Serverfault Is there a way to cause the system's time to run faster than real world time? My first thought is manipulating the ntp daemon to repeatedly and smoothly increment the clock . Any other ideas? And yes, I know this may have strange side affects. However, the system has no important or time critical interactions with systems outside of itself. And this may be a valuable testing technique.

  Read the article

• Can't connect to local MySQL server through socket

  - by Martin

  I was trying to tune the performance of a running mysql-server by running this command: mysqld_safe --key_buffer_size=64M --table_cache=256 --sort_buffer_size=4M --read_buffer_size=1M & After this i'm unable to connect mysql from the server where mysql is running. I get this error: ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (111) However, luckily i can still connect to mysql remotely. So all my webservers still have access to mysql and are running without any problems. Because of this though i don't want to try to restart the mysql server since that will probably mess everything up. Now i know that mysqld_safe is starting the mysql-server, and since the mysql server was already running i guess it's some kind of problem with two mysql servers running and listening to the same port. Is there some way to solve this problem without restarting the initial mysql server? UPDATE: This is what ps xa | grep "mysql" says: 11672 ? S 0:00 /bin/sh /usr/bin/mysqld_safe 11780 ? Sl 175:04 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/mysqld/mysqld.pid --socket=/var/run/mysqld/mysqld.sock --port=3306 11781 ? S 0:00 logger -t mysqld -p daemon.error 12432 pts/0 R+ 0:00 grep mysql

  Read the article

• Launch synergy client on boot in Mac OS X

  - by Herms

  I have a mac as a secondary machine at work. Currently I use synergy on my main machine to share its keyboard and mouse with the mac. I created a launch agent for my user to launch synergy when I log in, and that's working. However, this means I still have to pull out the mac's keyboard and mouse in order to log in. I tried making a user daemon so that it would launch on boot, but I get the following errors in the console: LaunchSynergy[52] Tue Jul 14 12:41:44 testmacpro.local synergyc[52] <Warning>: 3891612: (CGSLookupServerRootPort) Untrusted apps are not allowed to connect to or launch Window Server before login. LaunchSynergy[52] Tue Jul 14 12:41:44 testmacpro.local synergyc[52] <Error>: kCGErrorRangeCheck : On-demand launch of the Window Server is allowed for root user only. LaunchSynergy[52] Tue Jul 14 12:41:44 testmacpro.local synergyc[52] <Error>: kCGErrorRangeCheck : Set a breakpoint at CGErrorBreakpoint() to catch errors as they are returned LaunchSynergy[52] _RegisterApplication(), FAILED TO establish the default connection to the WindowServer, _CGSDefaultConnection() is NULL. Is there a way to get this to work? Looks like the Mac's security doesn't want to allow anything to take control of the window while at the login screen. I can understand that, but I'd like a way to override it, as it would make my life a lot easier.

  Read the article

• SQL Server Installaion error 0x84B40000

  - by Kurtevich

  I have a problem installing SQL Server 2008 R2. Long time ago I had it installed, and then uninstalled. It was left in "Add/remove programs", but I didn't pay attention on that. I had 2005 installed. And now there is a need to install 2008. I removed 2005 and started installing 2008, but it says that space on C: is not enough. That's when I found out that "Add/remove programs" shows it occupying more than 4 gigabytes, though I used to uninstall it. So I click "Remove", it shows all those many screens and validations, shows that removal completed, but the size of Program Files folder is still more than 4 GB. I removed (from "Add\remove programs" everything that had "SQL Server" in it's name, but that main "SQL Server 2008" item is still there and still 4 GB and uninstalling does nothing. Because installation of SQL Server did not show existing instances, and I don't see any running services related to SQL server (well, almost any, more details in the end), I though that this folder contains just some leftover staff and data and deleted it manually. Then agreed to removing of the item in "Add/remove programs" and everything looks clean. Now every time I try to install SQL Server (even in the minimum configuration), I receive the following error: SQL Server Setup has encountered the following error: The specified credentials that were provided for the SQL Server service are not valid. To continue, provide a valid account and password for the SQL Server service. Error code 0x84B40000. What is this service mentioned here? This error looks like I'm trying to add features to existing server and it can't login. But the setup didn't ask me for any credentials, except one username that couldn't be changed. Here are the services shown that can be related, both disabled and pointing to non-existing executables: SQL Active Directory Helper Service SQL Full-text Filter Daemon Launcher (MSSQLSERVER) I understand that this must be because of my manual deletion, but is there a way to clean it up now?

  Read the article

• Segmentation fault on login to mysql

  - by numberwhun

  Hello everyone! I recently did a fresh install of Ubuntu on my laptop (HP dv7, AMD Dual Core with 4 gigs RAM). I am working on installing my development environment and tools and one of the first things I was working on is getting MySQL installed. The following was my configure statement with options: ./configure --prefix=/usr/local/mysql --with-big-tables --with-unix-socket-path=/usr/local/mysql/tmp/mysql.sock --with-named-curses-libs=/lib/libncurses.so.5.7 After I did the make;make install, I did the post configuration such as setting the root password and installing the mysqld daemon in its rightful place. My issue is when I try to log in to mysql to start using it, the following shows what happens: $ mysql -u root -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 1 Server version: 5.1.42 Source distribution Segmentation fault I have searched Google extensively, I have searched through the mysql bugs database and I have yet to find anything that matches my issue. Here is the contents of my my.cnf file, in case you want to see it: $ cat /etc/my.cnf [mysqld] basedir=/usr/local/mysql datadir=/usr/local/mysql socket=/usr/local/mysql/tmp/mysql.sock [mysql.server] user=mysql #basedir=/var/lib [client] socket=/usr/local/mysql/tmp/mysql.sock [mysqld_safe] err-log=/usr/local/mysql/logs/mysqld.log pid-file=/var/run/mysqld/mysqld.pid I am really hoping that someone here can tell me what has gone wrong with my installation as I would really love to know. I welcome and look forward to all responses. Thank you in advance! Best regards, Jeff

  Read the article

• LogMeIn Hamachi for Linux

  - by tlunter

  So far most of my work using LogMeIn Hamachi has been from either a Mac OS X or Windows system to Windows or a Linux Computer. Recently I purchased a mini computer and have been running Ubuntu Server on it, as my little server. I knew LogMeIn had a Linux client that is command line only, but I often do all my work via command line anyway, so that wasn't an issue. I added my user to the correct local file so that I could run the hamachi daemon without sudo, and was able to connect to LogMeIn's service. I decided to set up my Linux server as a git server as well, and set it up correctly. The thing is, the server is behind my schools firewall and I need to use hamachi to get around that. Since most of the time I was using either Mac or Windows, I never had an issue sshing onto any of my computers since LogMeIn is fully featured for these OSs. From Linux (Arch) though, it seems like the client cannot correctly route to the LogMeIn IPs. I know from Windows I can connect to the Linux computers, both of them. From Linux (Arch) though, I can't connect to my Mac, Windows, or Linux server. It keeps just dropping the connection. I was wondering if there was some configuration that I would need to make for this to work. I understand that it is most likely going to be a static configuration since I assume it has to do with the computer not understanding that 5.*.*.* actually refers to another IP:Port. Has anyone had any experience getting this to work?

  Read the article

• Solaris SMF to Upstart on RHEL6

  - by aaa90210

  I am planning a migration from Solaris/x86 to RHEL6. Part of this migration will be migrating services from SMF to the RHEL6 equivalent, which appears to be upstart. While init.d scripts still seem to be supported, I want to take advantage of a more sophisticated init daemon, especially for features like job supervision (restarting etc). I would like to gather some thoughts on a few points: 1) Is upstart an adequate job supervisor, i.e. does it preclude the need for stand-alone managers like daemontools/supervise? 2) Upstart scripts seem very bare-bones compared to a typical init.d script. If I was porting an init.d script to Upstart, is it OK to just "exec /etc/init.d/myjob start"? This include RHEL installed programs like httpd. 3) Does upstart do anything is regards to pid files, and what are it's expectations in regards to the forking model of the process? 4) Are there any straightforward guides to the process management aspect of Upstart...and by that I mean the conditions around controlling restarting? e.g. how many times to restart the process before it goes into a maintenance state, or to ignore errors/core dumps in child processes of the supervised process. Any other relevant ideas or guides would be appreciated. TIA

  Read the article

• Xorg eating up too much RAM on Ubuntu 9.10 box

  - by Yang

  Xorg is eating up 444MB of 2GB total RAM on my Ubuntu 9.10 x86_64 machine with nvidia drivers installed for the nvidia G86 (GeForce 8300 GS). top shows: top - 18:21:41 up 6 days, 2:40, 9 users, load average: 0.46, 1.12, 1.22 Tasks: 266 total, 3 running, 262 sleeping, 1 stopped, 0 zombie Cpu(s): 8.4%us, 2.0%sy, 0.0%ni, 89.1%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2055736k total, 1965136k used, 90600k free, 3952k buffers Swap: 979924k total, 979908k used, 16k free, 102636k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1432 root 20 0 1154m 442m 7492 S 8 22.0 32:56.97 Xorg 18462 yang 20 0 1001m 219m 8356 S 0 10.9 5:13.25 chrome 24099 yang 20 0 865m 83m 13m S 0 4.2 0:06.91 chrome xrestop shows: xrestop - Display: :0.0 Monitoring 47 clients. XErrors: 0 Pixmaps: 40430K total, Other: 142K total, All: 40573K total res-base Wins GCs Fnts Pxms Misc Pxm mem Other Total PID Identifier 1c00000 21 46 1 19 697 9128K 18K 9146K 3169 x-nautilus-desktop 1000000 4 3 0 17 194 9000K 4K 9004K 3134 gnome-settings-daemon 1600000 51 2 1 25 1100 7648K 28K 7676K ? compiz For comparison, here's my other Ubuntu box, which also has compiz etc. enabled but with ATI RV370 (Radeon X300SE): top - 18:18:18 up 58 days, 4:27, 9 users, load average: 0.00, 0.00, 0.00 Tasks: 224 total, 1 running, 223 sleeping, 0 stopped, 0 zombie Cpu(s): 0.3%us, 0.3%sy, 0.0%ni, 98.8%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1024964k total, 987124k used, 37840k free, 247012k buffers Swap: 2048276k total, 94296k used, 1953980k free, 264744k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 24324 yang 20 0 61936 35m 6364 S 0 3.5 4:35.84 nxagent 1768 ntop 20 0 190m 32m 5388 S 1 3.2 283:36.15 ntop 1178 root 20 0 60588 29m 1788 S 0 3.0 5:48.89 console-kit-dae ... 1315 root 20 0 343m 4956 4020 S 0 0.5 3:43.87 Xorg Any ideas on how to get to the bottom of this? (i.e. not "Log out"/"Reboot") Thanks in advance.

  Read the article

• Email test deferred (mail transport unavailable) with ClamAV

  - by dirt

  I'm trying to set up a simple new mail server; when I send a test email to the server the email is getting hung up during delivery (user mapping is found) and the email is never found in /home/user/Maildir/new Here is my maillog after a fresh reboot and test email, there are a few warnings I am unfamiliar with. Can you please point me in the right direction? Oct 25 14:54:57 loki dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Oct 25 14:54:58 loki postfix/postfix-script[1369]: starting the Postfix mail system Oct 25 14:54:58 loki postfix/master[1370]: daemon started -- version 2.6.6, configuration /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: request to update table btree:/etc/postfix/smtpd_scache in non-postfix directory /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: redirecting the request to postfix-owned data_directory /var/lib/postfix Oct 25 14:56:00 loki postfix/smtpd[1455]: connect from mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/smtpd[1455]: 1CF5E20A8B: client=mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/cleanup[1461]: 1CF5E20A8B: message-id= Oct 25 14:56:01 loki postfix/qmgr[1379]: 1CF5E20A8B: from=, size=1788, nrcpt=1 (queue active) Oct 25 14:56:01 loki postfix/qmgr[1379]: warning: connect to transport private/scan: No such file or directory Oct 25 14:56:01 loki postfix/error[1462]: 1CF5E20A8B: to=, orig_to=, relay=none, delay=0.18, delays=0.15/0.02/0/0.01, dsn=4.3.0, status=deferred (mail transport unavailable) Oct 25 14:56:01 loki postfix/smtpd[1455]: disconnect from mail-ob0-f180.google.com[209.85.214.180] master.cf snippets: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd submission inet n - n - - smtpd -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING smtps inet n - n - - smtpd -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING scan unix - - n - 16 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes 127.0.0.1:10026 inet n - n - 16 smtpd -o content_filter= -o local_recipient_maps= -o relay_recipient_maps= -o smtpd_restriction_classes= -o smtpd_client_restrictions= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks_style=host -o smtpd_authorized_xforward_hosts=127.0.0.0/8

  Read the article

• How to Change the Kerberos Default Ticket Lifetime

  - by user40497

  Our KDC servers are running either Ubuntu Dapper (2.6.15-28) or Hardy (2.6.24-19). The Kerberos software is the MIT implementation of Kerberos 5. By default, a Kerberos ticket lasts for 10 hours. However, we'd like to increase it a bit (e.g. 14 hours) to suit our needs better. I had done the following but the ticket lifetime still stays at 10 hours: 1) On all the KDC servers, set the following parameter under [realms] in /etc/krb5kdc/kdc.conf and restarted the KDC daemon: max_life = 14h 0m 0s 2) Via "kadmin", changed the "maxlife" for a test principal via "modprinc -maxlife 14hours ". "getprinc " shows that the maximum ticket life is indeed 14 hours: Maximum ticket life: 0 days 14:00:00 3) On a Kerberos client machine, set the following parameters under [libdefaults], [realms], [domain_realm], and [login] in /etc/krb5.conf (everywhere basically since nothing I tried had worked): ticket_lifetime = 13hrs default_lifetime = 13hrs With the above settings, I suppose that the ticket lifetime would be capped at 13 hours. When I do "k5start -l 14h -t ", I see that the end time for the "renew until" line is now 14 hours from the starting time: Valid starting Expires Service principal 04/13/10 16:42:05 04/14/10 02:42:05 krbtgt/@ renew until 04/14/10 06:42:03 "-l 13h" would make the end time in the "renew until" line 13 hours after the starting time. However, the ticket still expires in 10 hours (04/13 16:42:05 - 014/14 02:42:05). Am I not changing the right configuration file(s)/parameter(s), not specifying the right option when obtaining a Kerberos ticket, or something else? Any feedback is greatly appreciated! Thank you!

  Read the article

• jetty - javax.naming.InvalidNameException: A flat name can only have a single component

  - by Dinesh Pillay

  I have been breaking my head against this for too much time now. I'm trying to get maven + jetty + jotm to play nice but it looks like its too much to ask for :( Below is my jetty.xml:- <?xml version="1.0"?> <!DOCTYPE Configure PUBLIC "-//Jetty//Configure//EN" "http://www.eclipse.org/jetty/configure.dtd"> <Configure id="Server" class="org.mortbay.jetty.Server"> <New id="jotm" class="org.objectweb.jotm.Jotm"> <Arg type="boolean">true</Arg> <Arg type="boolean">false</Arg> <Call id="tm" name="getTransactionManager" /> <Call id="ut" name="getUserTransaction" /> </New> <New class="org.mortbay.jetty.plus.naming.Resource"> <Arg /> <Arg>javax.transaction.TransactionManager</Arg> <Arg><Ref id="ut" /></Arg> </New> <New id="tx" class="org.mortbay.jetty.plus.naming.Transaction"> <Arg><Ref id="ut" /></Arg> </New> <New class="org.mortbay.jetty.plus.naming.Resource"> <Arg>myxadatasource</Arg> <Arg> <New id="myxadatasourceA" class="org.enhydra.jdbc.standard.StandardXADataSource"> <Set name="DriverName">org.apache.derby.jdbc.EmbeddedDriver</Set> <Set name="Url">jdbc:derby:protodb;create=true</Set> <Set name="User"></Set> <Set name="Password"></Set> <Set name="transactionManager"> <Ref id="tm" /> </Set> </New> </Arg> </New> <New id="protodb" class="org.mortbay.jetty.plus.naming.Resource"> <Arg>jdbc/protodb</Arg> <Arg> <New class="org.enhydra.jdbc.pool.StandardXAPoolDataSource"> <Arg> <Ref id="myxadatasourceA" /> </Arg> <Set name="DataSourceName">myxadatasource</Set> </New> </Arg> </New> And this is the maven plugin configuration:- <plugin> <groupId>org.mortbay.jetty</groupId> <artifactId>maven-jetty-plugin</artifactId> <configuration> <scanIntervalSeconds>10</scanIntervalSeconds> <stopKey>ps</stopKey> <stopPort>7777</stopPort> <webAppConfig> <contextPath>/ps</contextPath> </webAppConfig> <connectors> <connector implementation="org.mortbay.jetty.nio.SelectChannelConnector"> <port>7070</port> <maxIdleTime>60000</maxIdleTime> </connector> </connectors> <jettyConfig>src/main/webapp/WEB-INF/jetty.xml</jettyConfig> </configuration> <executions> <execution> <id>start-jetty</id> <phase>pre-integration-test</phase> <goals> <goal>run</goal> </goals> <configuration> <scanIntervalSeconds>0</scanIntervalSeconds> <daemon>true</daemon> </configuration> </execution> <execution> <id>stop-jetty</id> <phase>post-integration-test</phase> <goals> <goal>stop</goal> </goals> </execution> </executions> <dependencies> <dependency> <groupId>org.apache.derby</groupId> <artifactId>derby</artifactId> <version>10.6.1.0</version> </dependency> <dependency> <groupId>jotm</groupId> <artifactId>jotm</artifactId> <version>2.0.10</version> <exclusions> <exclusion> <groupId>javax.resource</groupId> <artifactId>connector</artifactId> </exclusion> </exclusions> </dependency> <dependency> <groupId>com.experlog</groupId> <artifactId>xapool</artifactId> <version>1.5.0</version> </dependency> <dependency> <groupId>javax.resource</groupId> <artifactId>connector-api</artifactId> <version>1.5</version> </dependency> <dependency> <groupId>javax.transaction</groupId> <artifactId>jta</artifactId> <version>1.0.1B</version> </dependency> <!-- <dependency> <groupId>javax.jts</groupId> <artifactId>jts</artifactId> <version>1.0</version> </dependency> --> </dependencies> </plugin> I am using maven-jetty-plugin-6.1.24 cause I couldn't get the later one's to work either. When I execute this I get the following exception:- 2010-06-16 09:03:13.423:WARN::Config error at javax.transaction.TransactionManager java.lang.reflect.InvocationTargetException [INFO] ------------------------------------------------------------------------ [ERROR] BUILD ERROR [INFO] ------------------------------------------------------------------------ [INFO] Failure A flat name can only have a single component [INFO] ------------------------------------------------------------------------ Caused by: javax.naming.InvalidNameException: A flat name can only have a single component at javax.naming.NameImpl.addAll(NameImpl.java:621) at javax.naming.CompoundName.addAll(CompoundName.java:442) at org.mortbay.jetty.plus.naming.NamingEntryUtil.makeNamingEntryName(NamingEntryUtil.java:136) at org.mortbay.jetty.plus.naming.NamingEntry.save(NamingEntry.java:196) at org.mortbay.jetty.plus.naming.NamingEntry.(NamingEntry.java:58) at org.mortbay.jetty.plus.naming.Resource.(Resource.java:34) ... 31 more Help!

  Read the article

• Help setting up a secondary authoritative DNS server.

  - by GLB03

  We have three Authoritative DNS servers and three recursive/caching DNS servers on my campus. Authoritative servers DNS1- Windows 2003 DNS2- Old Red Hat ----- Replacing w/ newer version DNS3- Windows 2008 (I installed) Caching and Recursive resolvers servers Server1- Windows 2003 Server2- CentOS 5.2 (I installed) Server3- CentOS 5.3 (I installed) I am replacing DNS2 with a newer Red Hat version, but have no documentation on how it was implemented. I have setup caching and windows authoritative servers, but not a linux secondary authoritative server. I have a perl script from the original server that pulls data from our DNS1 server. We use DJBDNS and TinyDNS on our linux servers. Our Network Engineer says the DNS2 server I am replacing is an authoritative server that doesn't need to be caching, but the only instructions I see is for an Authoritative server that does caching as well. Can someone point me in the right directions. I thought I was on the right track with using these instructions but when I query my new dns server I get "No response from server", I have temporarily disabled iptables to eliminate it from being an issue. ps -aux | grep dns avahi 3493 0.0 0.2 2600 1272 ? Ss Apr24 0:05 avahi-daemon: running [newdns2.local] root 5254 0.0 0.1 3920 680 pts/0 R+ 09:56 0:00 grep dns root 6451 0.0 0.0 1528 308 ? S Apr29 0:00 supervise tinydns dnslog 6454 0.0 0.0 1540 308 ? S Apr29 0:00 multilog t ./main tinydns 9269 0.0 0.0 1652 308 ? S Apr29 0:00 /usr/local/bin/tinydns

  Read the article

• Gwibber on Ubuntu doesn't open

  - by Radian

  Gwibber Doesn't open . When I tried to Open it from Command Line I got this error ** (gwibber:3752): WARNING **: Trying to register gtype 'WnckWindowState' as enum when in fact it is of type 'GFlags' ** (gwibber:3752): WARNING **: Trying to register gtype 'WnckWindowActions' as enum when in fact it is of type 'GFlags' ** (gwibber:3752): WARNING **: Trying to register gtype 'WnckWindowMoveResizeMask' as enum when in fact it is of type 'GFlags' No dbus monitor yet Updating... ERROR:dbus.proxies:Introspect error on com.Gwibber.Service:/com/gwibber/Service: dbus.exceptions.DBusException: org.freedesktop.DBus.Error.NoReply: Message did not receive a reply (timeout by message bus) Traceback (most recent call last): File "/usr/bin/gwibber", line 67, in client.Client() File "/usr/lib/python2.6/dist-packages/gwibber/client.py", line 447, in init self.w = GwibberClient() File "/usr/lib/python2.6/dist-packages/gwibber/client.py", line 29, in init self.model = gwui.Model() File "/usr/lib/python2.6/dist-packages/gwibber/gwui.py", line 43, in init self.services = json.loads(self.daemon.GetServices()) File "/usr/lib/pymodules/python2.6/dbus/proxies.py", line 68, in call return self._proxy_method(*args, **keywords) File "/usr/lib/pymodules/python2.6/dbus/proxies.py", line 140, in call **keywords) File "/usr/lib/pymodules/python2.6/dbus/connection.py", line 620, in call_blocking message, timeout) dbus.exceptions.DBusException: org.freedesktop.DBus.Error.NoReply: Message did not receive a reply (timeout by message bus) I tried to remove it and to Install again but It has the same error It was Working probably , then suddenly it didn't

  Read the article

• OpenVPN Client timing out

  - by Austin

  I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

  Read the article

• Backup data rate on Raspberry Pi maxing out at 5 Mb/s. Why?

  - by bastibe

  I set up my Raspberry Pi as a Time Machine, as documented here. At the moment, the Raspberry Pi is connected to my MacBook Pro using a direct Ethernet cable. Also, an external hard drive (laptop drive) is connected to the Raspberry Pi using the USB port. However, backups are pretty slow. Activity Monitor claims that the Network is transferring a very steady 5 Mb/s, where my Time Capsule is transferring up to 8 Mb/s with a lot of fluctuation. The Raspberry Pi self-reports (top) that its CPU is only half-used, with about equal parts afpd, usb-storage and jbd2/sda1-8. Thus, I think that the processing power of the Raspberry Pi does not seem to be the problem here. To me, this looks like there is some kind of bottleneck that maxes out at 5 Mb/s thus potentially having my backups run at less than their potential speed. To the best of my knowledge, this might be the afp-daemon, the usb-bus or the external hard drive. So, my question is, how could I identify the true culprit and what can I do about it?

  Read the article

• Recover mysql database - mysqldump gives "table <tablename> doesn't exist (1146)"

  - by Matthew

  Backstory Ubuntu died (wouldn't boot) and I couldn't fix it. I booted a live cd to recover the important stuff and saved it to my NAS. One of the things I backed up was /var/lib/mysql. Reinstalled with Linux Mint because I was on Ubuntu 10.0.4 this was a good opportunity to try a new distro (and I don't like Unity). Now I want to recover my old mediawiki, so I shut down mysql daemon, cp -R /media/NAS/Backup/mysql/mediawiki@002d1_19_1 /var/lib/mysql/, set file ownership and permissions correctly, and start mysql back up. Problem Now I'm trying to export the database so I can restore the database, but when I execute the mysqldump I get an error: $ mysqldump -u mediawikiuser -p mediawiki-1_19_1 -c | gzip -9 > wiki.2012-11-15.sql.gz Enter password: mysqldump: Got error: 1146: Table 'mediawiki-1_19_1.archive' doesn't exist when using LOCK TABLES Things I've tried I tried using --skip-lock-tables but I get this: Error: Couldn't read status information for table archive () mysqldump: Couldn't execute 'show create table `archive`': Table 'mediawiki-1_19_1.archive' doesn't exist (1146) I tried logging in to mysql and I can list the tables that should be there, but trying to describe or select from them errors out the same way as the dump: mysql> show tables; +----------------------------+ | Tables_in_mediawiki-1_19_1 | +----------------------------+ | archive | | category | | categorylinks | ... | user_properties | | valid_tag | | watchlist | +----------------------------+ 49 rows in set (0.00 sec) mysql> describe archive; ERROR 1146 (42S02): Table 'mediawiki-1_19_1.archive' doesn't exist I believe mediawiki was installed using innodb and binary data. Am I screwed or is there a way to recover this?

  Read the article

• How to stop Cron from sending messages about errors

  - by Beck

  I have this strange mails comming from cron: Return-Path: <[email protected]> Delivered-To: [email protected] Received: by domain.com (Postfix, from userid 0) id 6F944264D0; Mon, 10 Jan 2011 10:35:01 +0000 (UTC) From: [email protected] (Cron Daemon) To: [email protected] Subject: Cron <root@domain> lynx -dump http://www.domain.com/cron/realqueue Content-Type: text/plain; charset=ANSI_X3.4-1968 X-Cron-Env: <SHELL=/bin/sh> X-Cron-Env: <PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin> X-Cron-Env: <HOME=/root> X-Cron-Env: <LOGNAME=root> Message-Id: <[email protected]> Date: Mon, 10 Jan 2011 10:35:01 +0000 (UTC) /bin/sh: lynx: not found I have this cron settings in crontab file: SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin */5 * * * * lynx -dump http://www.domain.com/cron/realqueue 17 * * * * root cd / && run-parts --report /etc/cron.hourly 25 6 * * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily ) 47 6 * * 7 root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.weekly ) 52 6 1 * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.monthly ) Lynx is installed on my Ubuntu as well. Ofc in place of domain.com is my domain, just replaced. Thanks ;)

  Read the article

• Should windows services be created with custom users, or should I use one of LocalSystem/LocalServic

  - by Justin Dearing

  I'm asking the question in general for the average custom developed NT service or unix OSS daemon ported to windows with SCM support. However, at the moment my immediate concern is for mongodb. From my experience with UNIX I like all my services to run as different unprivileged users. The way this has translated to windows is as follows: Create a local (or domain if it has to talk to SQL server) windows user with a long random password (lately an ASCII85 encoded guid generated from a different machine). Set it to next expire and forbid it from changing its password. Remove that user from the "Users Group". Grant that user "Login as a Service" permission. Give it read permission to the folder where the app resides, and write permission to the logs and data files the applications use. Assign the user to the service. Troubleshoot until the service starts. My feeling is that the unprivileged users are less powerful than the 3 special service users. I also feel that by isolating which users run which services, I would limit collateral damage if a way to compromise one service was found.

  Read the article

• What are useful .screenrc settings?

  - by gyaresu

  Basically like some of my own that I've posted below. I'm looking for added functionality to the programme 'screen'. At the very least have a look at the last line for a fantastic 'menu bar' at the bottom of a screen session. ## gyaresu's .screenrc 2008-03-25 # http://delicious.com/search?p=screenrc # Don't display the copyright page startup_message off # tab-completion flash in heading bar vbell off # keep scrollback n lines defscrollback 1000 # Doesn't fix scrollback problem on xterm because if you scroll back # all you see is the other terminals history. # termcapinfo xterm|xterms|xs|rxvt ti@:te@ # These will let you use bind -c selectHighs 0 select 10 #these three commands are bind -c selectHighs 1 select 11 #added to the command-class bind -c selectHighs 2 select 12 #selectHighs bind -c selectHighs 3 select 13 bind -c selectHighs 4 select 14 bind -c selectHighs 5 select 15 bind - command -c selectHighs #bind the hyphen to #command-class selectHighs screen -t rtorrent 0 rtorrent #screen -t tunes 1 ncmpc --host=192.168.1.4 --port=6600 #was for connecting to MPD music server. screen -t stuff 1 screen -t irssi 2 irssi screen -t dancing 4 screen -t python 5 python screen -t giantfriend 6 these_are_ssh_to_server_scripts.sh screen -t computerrescue 7 these_are_ssh_to_server_scripts.sh screen -t BMon 8 bmon -p eth0 screen -t htop 9 htop screen -t hellanzb 10 hellanzb screen -t watching 3 #screen -t interactive.fiction 8 #screen -t hellahella 8 paster serve --daemon /home/gyaresu/downloads/hellahella/hella.ini shelltitle "$ |bash" # THIS IS THE PRETTY BIT #change the hardstatus settings to give an window list at the bottom of the ##screen, with the time and date and with the current window highlighted hardstatus alwayslastline #hardstatus string '%{= mK}%-Lw%{= KW}%50>%n%f* %t%{= mK}%+Lw%< %{= kG}%-=%D %d %M %Y %c:%s%{-}' hardstatus string '%{= kG}[ %{G}%H %{g}][%= %{= kw}%?%-Lw%?%{r}(%{W}%n*%f%t%?(%u)%?%{r})%{w}%?%+Lw%?%?%= %{g}][%{B} %d/%m %{W}%c %{g}]'

  Read the article

• When pointing to new DNS servers is there any chance of E-mails being lost if the old E-mail hosting service is still up?

  - by LaserBeak

  I am changing webhosts and will be using the new hosts mail servers instead of the old ones. I have created all the correctly named mailboxes on the new service but have also not yet cut ties with the old webhost. I am expecting that even if the new DNS values which point to the new hosts DNS servers and respective SOA\zone file with the new MX values have not yet propagated and an E-mail is directed at the old hosts mail servers as per the mx records in the SOA\zone records which the old hosting provider holds, the E-mail would still come through to the mailbox that's on the old host providers mail servers. So I am just trying to reaffirm if I got this right and it's essentially impossible for me to loose an E-mail since it will hit either the old hosts mail servers or the new ones ? Also is it possible to configure the same E-mail account to check and collect mail from different mail servers by entering multiple pop3 addresses ? And if I choose to keep the old web hosts mail hosting services as a backup by specifying the mx records for it with a lower priority in the SOA records hosted by the new webhost, is it possible to have any incoming E-mails sent to both servers by the mail daemon so I have two copies? Or is my only option having the primary mail server forward the E-mail somehow to the old mailserver ?

  Read the article

• Postfix does not work after setting server hostname from plesk

  - by Michael

  I have recently set my server hostname from localhost.localdomain to xx.mydomain.com from the plesk control panel. However after doing this change postfix has stopped working, I tried restarting and regenerating the config files but to no avail. I am not familiar with postfix but I believe there is a setting to be changed in main.cf. Here are the relevant errors I receive: postfix/postfix-script: starting the Postfix mail system postfix/master: daemon started -- version 2.8.4, configuration /etc/postfix postfix/cleanup: fatal: host/service localhost/12768 not found: Name or service not known postfix/pickup: warning: maildrop/E5559996219: error writing 4FA2C996217: queue file write error postfix/master: warning: process /usr/libexec/postfix/cleanup pid 15334 exit status 1 postfix/master: warning: /usr/libexec/postfix/cleanup: bad command startup -- throttling Any ideas? EDIT Setting it back to localhost.localdomain makes it work again. The only references to localhost/12768 I can find in main.cf are: smtpd_milters = inet:localhost:12768 non_smtpd_milters = inet:localhost:12768 Should something be changed here? These two lines stay the same when I change the hostname. EDIT If I comment out the two mail filter lines (the ones shown above) and restart, postfix works with the new hostname. However this is obviously not the ideal solution...

  Read the article

• Exchange 2007 relay from sendmail, message "Undelivered". Possible reasons?

  - by garlicman

  Note: This is my re-post from Stackoverflow. I've been messing with a test environment for security purposes where a DMZ RHEL5 sendmail server is used as a relay for an Exchange 2007 server. Exchange is working in the environment, I have Vista and XP VMs using Outlook on the Domain to send e-mail to each other. I've been trying to simulate an external internet VM sending an e-mail to the DMZ sendmail relay, which forwards to the Exchange server. Before everyone thinks this is too big a problem/question, I've followed the sendmail/Exchange guides and all I want to know is how I can determine why a relayed message/e-mail in Exchange is "Undelivered". Basically I send a SMTP message to the sendmail server, which relayed to my Exchange. The /var/log/maillog shows the e-mail being relayed to Exchange. Nov 17 13:41:22 externalmailserver sendmail[9017]: pAHIfMuW009017: from=<[email protected]>, size=1233, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA, relay=[10.50.50.1] Nov 17 13:42:17 externalmailserver sendmail[9050]: pAHIfMuW009017: to=<[email protected]>, delay=00:00:55, xdelay=00:00:36, mailer=relay, pri=121233, relay=mailserver.xyz.local. [192.168.1.20], dsn=2.0.0, stat=Sent (<[email protected]> Queued mail for delivery) This is good, but the To never receives the e-mail from Exchange. So I started poking around Exchange. In the "Message Tracking" Troubleshooting Assistant I queried the processed messages and found this: (I had to copy and paste the cells... sorry for the format) 2011/11/17 RECEIVE SMTP <[email protected]> "Undelivered Mail Returned to Sender" [email protected] [email protected] 192.168.100.10 MAILSERVER\DMZ Relay [email protected] I just want to know if anyone has any suggestions on why the DMZ Relay Connector I setup isn't relaying and is instead returning the forwarded e-mail to sender as Undelivered? My Exchange Relay Receive Connector is pretty simple. The Exchange server's FQDN is set as the HELO response, all available IP addresses can receive relayed e-mail, and the IP address of my sendmail server is specifically set as a remote server.

  Read the article

• HAProxy "503 Service Unavailable" for webserver running on a KVM virtual machine

  - by Menda

  I'm setting up a server with KVM (IP 192.168.0.100) and I have created inside of it one virtual machine using network bridging at 192.168.0.194. This virtual machine has an nginx instance running, which I can access from the server or from any computer computer in the internal network just typing in the browser http://192.168.0.194. However, I try configure HAProxy in the same server that hosts KVM and looking the status page of HAProxy it always shows the virtual machine as "DOWN". If I try from the server http://localhost, it should be the same than if I go to http://192.168.0.194. My goal is to build a reverse proxy, but I tried this little example and won't work. What am I doing bad? This is my config file in the server: # /etc/haproxy/haproxy.cfg global maxconn 4096 user haproxy group haproxy daemon defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen ServerStatus *:8081 mode http stats enable stats auth haproxy:haproxy listen Server *:80 mode http balance roundrobin cookie JSESSIONID prefix option httpclose option forwardfor option httpchk HEAD /check.txt HTTP/1.0 server mv1 192.168.0.194:80 cookie A check Thanks.

  Read the article

• Windows 7 64-bit installation from alternative media (no DVD/USB Flash drive)

  - by Niels Willems

  Greetings I currently have Windows 7 x86 installed on my computer. I want to install Windows 7 x64 on a different partition on my computer. However there is a little issue, I cannot run the x64 install from Windows 7 x86 which I currently have. I was planning to Install Windows 7 x64 on another partition to then boot up from that partition to install it on the partition I actually want my OS on. Once that is complete I could just format the partition from the Windows 7 x64 that I didn't need anymore. But the installer will not run from the x86 version of Windows 7 even though I do not want to upgrade that Windows directly. The reason I'm doing this in such a weird way is that my optical drive is broken and I'm really not into buying a new one since I would use it like once every year or so. I also don't have a USB Flash Drive which is big enough to hold the installation files. As far as I'm aware I cannot use an external hard drive such as this one, which I do have. Are there any alternatives in which I can install Windows 7 x64 or am I forced into buying a USB Flash Drive or new optical drive? Thank you in advance for your replies. Edit: This picture shows my current partitions on my laptop. I want to get Windows 7 x64 on the C partition but have to install it first on the F partition to then boot up the F partition windows to format C and install x64 on that one. My external drive is J. Edit 2: No alternative computer which has a DVD drive, install files are located on an iso from MA3D. To install my 32 bit version I mounted the ISO in Daemon Tools to replace my Windows Vista but since I cannot run 64 bit into my 32 bit OS this doesn't work.

  Read the article

< Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >