Search Results

Search found 31562 results on 1263 pages for 'dell mini 10'.

Page 46/1263 | < Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >

• NVIDIA Tesla K20C in Dell PowerEdge R720xd --- power cables

  - by CptSupermrkt

  I am trying to put an NVIDIA Tesla K20C into a Dell PowerEdge R720xd. I'm having a bit of trouble understanding the power requirements of the card. First, here is a picture of two pages of the same manual, which seems contradictory to me. One page says only a single connector is required, while the next page says both are required. The entire manual for the card can be found here: http://www.nvidia.com/content/PDF/kepler/Tesla-K20-Active-BD-06499-001-v02.pdf Here is an photo taken of the power connections on the card: And here is a photo of where those connectors need to go, onto the PCI-E riser of the r720xd: Neither the R720xd NOR the GPU came with the necessary cables. And given what appears to be a contradiction in the GPU manual (above), I'm not even sure at this point what we actually need. I have searched high and low online for things like 2x6 pin PCI-E to 8 pin male-to-male and so on, and for the life of me cannot find what we need. In case anyone needs it, the owner's manual of the R720xd can be found here: ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_poweredge/poweredge-r720xd_Owner%27s%20Manual_en-us.pdf The relevant page is page 68, which clearly indicates that the 8-pin female port on the riser card is for a GPU. The bottom line question: exactly what power cables do we need to buy, and where can we find them?

  Read the article

• Provisioning DELL servers using only linux tools

  - by Krist van Besien

  We have taken delivery of a bunch off Dell Poweredge Rack servers. Unfortunately when ordering it was neglegted to ask for dhcp to be enabled in the built in iDRAC controlers... So they are all stuck on the same IP address. Which means that I'll have to go to each of them individually and configure a new IP in the console... In the future I want to avoid that. Now Dell proposes to deliver the next batch with auto discovery enabled. As I understand this means that when the machine wakes up for the first time the iDRAC will request a DHCP address. The DHCP server then supposedly also provides a "provisioning" server, that provides it with a username and password, and a configuration to be applied. This would allow us to for example configure things like RAID automatically. However, I can't seem to find a way to set up such a provisioning server that does not involve setting up a windows machine. I want to use Linux tools exclusively. Is there a way to do this? I want to just rack servers, switch them on, and then do everything remotely. And that using only linux tools?

  Read the article

• Dell Latitude D510 Runs From Battery But Not AC Adapter

  - by Jason George

  I have a Dell Latitude D510 that went belly up around two years ago. It will run from the battery, however, the wall adapter will neither power the machine nor charge the battery. Once the battery is dead, the machine is dead. Since it died I've searched repeatedly for solutions. I've tried a new AC adapter and even removed and replaced the DC jack thinking one of the solder joints might be bad. Both to no avail. After two years of searching I finally found the answer today. Since it's such a simple fix and I had such a hard time finding it I wanted to post the info for others (as it is apparently a common issue with the D510). -----SOLUTION----- It seems this is commonly caused by a cracked solder joint at pin 1 on an inductor filter pair (FL2) near the power jack. Pins 1 and 4 are ground and pins 2 and 3 are power. There should be 20V from 1 to 2 and 3. Anything less indicates a cracked joint that is increasing resistance and dropping the supply voltage. Repair simply requires reflowing all four pins with a little added solder for security. Detailed instructions can be found here. Dell Latitude D510 solder problem

  Read the article

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• Workaround for Dell "Power Supply Not Recognised" issue

  - by Haedrian

  So, I have a Dell Inspirion and the power supply port appears to be damaged. Basically when I plug it in I get a nice popup telling me that it couldn't detect that its a Dell power supply so it won't charge the battery and underclocks the system. It still works for other purposes (that is, giving power) I thought it was the actual power supply cable so I bought a new one, that worked for a while, provided I inserted it at JUST THE RIGHT angle. But now that's not working anymore, so I assume its the part which connects to the computer. The battery charging I can live without, the underclocking I can't. I'd like a way around this issue. Things I've tried: Updating the BIOS Replacing the power supply cable Inserting it at different angles Turning it off and on again Swearing at it Twisting it while inserting it So, is there a workaround somehow? I'd like to avoid taking out my soldering kit and risking permanently damaging expensive equipment if that's allright. I'm hoping for a software solution. Added: The exact model is a Del Inspirion N5010

  Read the article

• File Access problems with SLES 10 SP2 OES2 SP1

  - by Blackhawk131

  We have identified a couple of repeatable, demonstrable scenarios with unexplained rejected folder access on our servers for Mac users. Hopefully, this can be presented to Novell for a solution. What we did to demonstrate scenario 1; 1. setup a PC and Mac side-by-side 2. login to our server and open up to a central location on both Mac and PC 3. on the PC in that central location create a folder 4. on the Mac in that central location drag the created folder to the Mac desktop, this should work fine, no problem 5. on the PC rename that folder 6. on the Mac drag a file to that renamed folder, this should error with the following message; a. You cannot copy some of these items to the destination because their names are too long for the destination. Do you want to skip copying these items and continue copying the other items? b. Select skip, response is the filename is copied to the location with zero or small byte size. Try opening it and you get file is corrupted error message. What we did to demonstrate scenario 2; 1. setup a PC and Mac side-by-side 2. login to our server and open up to a central location on both Mac and PC 3. on the PC in that central location create a folder then create a subfolder 4. copy some content into the subfolder 5. on the Mac in that central location drag the created top level folder to the Mac desktop, this should work fine, no problem 6. on the PC rename that subfolder 7. on the Mac drag that top level folder to the Mac desktop, this should error on the Mac with the following; a. The operation cannot be completed because you do not have sufficient privileges for b. The operation cannot be completed because you do not have sufficient privileges for 8. on the Mac, if you open that subfolder you can see the file copied in step 4 above but, you can not open that file, you get the following message if you try; a. There was an error opening this document. You do not have permission to open this file. 9. on the PC drag some content into the top level folder 10. on the Mac you can open that file directly from the server or copy it locally, no problem, however-the subfolder is still corrupted or locked, whichever 11. on the PC rename the top level folder 12. on the Mac that same file just opened in step 10 above is now not accessible, get the following message; a. The document could not be opened. I have observed some variances in the above. For instance, a change on the PC side may take a moment before you can observer or act on the Mac side - kind of like the server is slow to respond. Also, the error message may vary. However, the key is once a folder, or subfolder, gets renamed by a PC, Mac problems commence. The solution is to create a new folder from a PC and copy the contents of the corrupted folder to the new folder and not rename the folder name. This has to be done on a PC because the corrupted folder is not accessible by a Mac user. Another problem that dovetails with the above is that we know certain characters are not allowed for PC folder or filenames. If a Mac user creates a folder with a slash in the file name, from the PC the user does not see that slash in the name. As soon as the PC user copies a file to that folder, the Mac user is locked from that folder. Will get the following error message; - Sorry, the operation could not be completed because an unexpected error occurred. - (Error code - 50) In addition to the above mentioned character issue with folders, the problem is more evil with filenames. If, for example, you create a file with a slash in the filename on a Mac and copy it to the server you will get the following error message; - You cannot copy some of these items to the destination because their names are too long for the destination. Do you want to skip copying these items and continue copying the other items? Select either Stop or Skip buttons. It does not matter which button is selected. The file name gets copied to the destination location at a reduced size. Depending on the file type, the icon associated with the file may or may not be present. Furthermore, if you open that file on the server you will get the following message; - Couldnt open the file. It may be corrupt or a file format that doesnt recognize. From the users perspective, if they are not observant of the icon or file size, they may disregard the error message and think their file has copied as intended. Only later do they discover the file is corrupt if they open that file. I want to make a note on this problem. It is the PC causing the issue. You can change folder and file names all day on a MAC and you don't have a problem as long as a character is not the issue. Once you change the file name or folder name from a PC the entire folder structure from that level down is corrupted. But it has to be resolved from a PC by creating a new folder and copying the contents to the new folder like stated above. Is something not configured correctly? SUSE Linux Enterprise Server 10 (x86_64) VERSION = 10 PATCHLEVEL = 2 LSB_VERSION="core-2.0-noarch:core-3.0-noarch:core-2.0-x86_64:core-3.0-x86_64" Novell Open Enterprise Server 2.0.1 (x86_64) VERSION = 2.0.1 PATCHLEVEL = 1 BUILD Note: We use Novell clients on all windows systems to connect to the servers for file access and network storage. We use AFP to allow OSx systems to connect to servers.

  Read the article

• File Access problems with SLES 10 SP2 OES2 SP1

  - by Blackhawk131

  We have identified a couple of repeatable, demonstrable scenarios with unexplained rejected folder access on our servers for Mac users. Hopefully, this can be presented to Novell for a solution. What we did to demonstrate scenario 1; 1. setup a PC and Mac side-by-side 2. login to our server and open up to a central location on both Mac and PC 3. on the PC in that central location create a folder 4. on the Mac in that central location drag the created folder to the Mac desktop, this should work fine, no problem 5. on the PC rename that folder 6. on the Mac drag a file to that renamed folder, this should error with the following message; a. You cannot copy some of these items to the destination because their names are too long for the destination. Do you want to skip copying these items and continue copying the other items? b. Select skip, response is the filename is copied to the location with zero or small byte size. Try opening it and you get file is corrupted error message. What we did to demonstrate scenario 2; 1. setup a PC and Mac side-by-side 2. login to our server and open up to a central location on both Mac and PC 3. on the PC in that central location create a folder then create a subfolder 4. copy some content into the subfolder 5. on the Mac in that central location drag the created top level folder to the Mac desktop, this should work fine, no problem 6. on the PC rename that subfolder 7. on the Mac drag that top level folder to the Mac desktop, this should error on the Mac with the following; a. The operation cannot be completed because you do not have sufficient privileges for b. The operation cannot be completed because you do not have sufficient privileges for 8. on the Mac, if you open that subfolder you can see the file copied in step 4 above but, you can not open that file, you get the following message if you try; a. There was an error opening this document. You do not have permission to open this file. 9. on the PC drag some content into the top level folder 10. on the Mac you can open that file directly from the server or copy it locally, no problem, however-the subfolder is still corrupted or locked, whichever 11. on the PC rename the top level folder 12. on the Mac that same file just opened in step 10 above is now not accessible, get the following message; a. The document could not be opened. I have observed some variances in the above. For instance, a change on the PC side may take a moment before you can observer or act on the Mac side - kind of like the server is slow to respond. Also, the error message may vary. However, the key is once a folder, or subfolder, gets renamed by a PC, Mac problems commence. The solution is to create a new folder from a PC and copy the contents of the corrupted folder to the new folder and not rename the folder name. This has to be done on a PC because the corrupted folder is not accessible by a Mac user. Another problem that dovetails with the above is that we know certain characters are not allowed for PC folder or filenames. If a Mac user creates a folder with a slash in the file name, from the PC the user does not see that slash in the name. As soon as the PC user copies a file to that folder, the Mac user is locked from that folder. Will get the following error message; - Sorry, the operation could not be completed because an unexpected error occurred. - (Error code - 50) In addition to the above mentioned character issue with folders, the problem is more evil with filenames. If, for example, you create a file with a slash in the filename on a Mac and copy it to the server you will get the following error message; - You cannot copy some of these items to the destination because their names are too long for the destination. Do you want to skip copying these items and continue copying the other items? Select either Stop or Skip buttons. It does not matter which button is selected. The file name gets copied to the destination location at a reduced size. Depending on the file type, the icon associated with the file may or may not be present. Furthermore, if you open that file on the server you will get the following message; - Couldnt open the file. It may be corrupt or a file format that doesnt recognize. From the users perspective, if they are not observant of the icon or file size, they may disregard the error message and think their file has copied as intended. Only later do they discover the file is corrupt if they open that file. I want to make a note on this problem. It is the PC causing the issue. You can change folder and file names all day on a MAC and you don't have a problem as long as a character is not the issue. Once you change the file name or folder name from a PC the entire folder structure from that level down is corrupted. But it has to be resolved from a PC by creating a new folder and copying the contents to the new folder like stated above. Is something not configured correctly? SUSE Linux Enterprise Server 10 (x86_64) VERSION = 10 PATCHLEVEL = 2 LSB_VERSION="core-2.0-noarch:core-3.0-noarch:core-2.0-x86_64:core-3.0-x86_64" Novell Open Enterprise Server 2.0.1 (x86_64) VERSION = 2.0.1 PATCHLEVEL = 1 BUILD Note: We use Novell clients on all windows systems to connect to the servers for file access and network storage. We use AFP to allow OSx systems to connect to servers.

  Read the article

• Embedding BIP just got easier!

  - by Tim Dexter

  To make up for yesterday's documentation faux pas, when I referenced Kan's blog as a source for the debug feature over Leslie's fine official documentation that had come out some time before Kan's blog. Apologies again Leslie! I noticed another new feature that I was unaware of in the New Features guide for 10.1.3.4.1. The ability to remove the BI Publisher header from the user interface so you can get this: instead of this. Useful? If you wanted to host BIP inside another application such as a portal or custom app, you can make the BIP UI app look much more integrated. By default you still get our 'blue' look and feel' but I have documented else where how you can change that. For instance, now you can have BIP hosted inside a BIEE instance and provide access to all the reports a user might wish to run with very little effort rather than picking and choosing what to bubble up to the dashboard. How do you do it? Get on over to the New Features guide and find out, there are some other goodies there too. Note to self, RTFM!

  Read the article

• Enable wireless on Dell Inspiron 1300

  - by Simon

  As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

  Read the article

• Solaris 10 zlogin logs in, logs out immediately

  - by Spelevink

  On a SPARC v445 running Solaris 10 9/10, had to rebuild rpool and reattached the three existing mirrored zpools on the other existing disks, with their zfs filesystems and NG zones intact. The zones have been configured with zonecfg -z ZONENAME create etc. ... and are now online using zoneadm -z ZONENAME attach -U then simply booting after being in installed state, but I cannot zlogin to any of the zones except one. It shows that I am logged in, then a blank line, then immediately logged out again. When I try to login using zlogin -C ZONENAME I cannot; the error message is: May 15 15:43:46 <hostname> login: open_module: stat(/usr/lib/security/pam_mkhomedir.so.1) failed: no such file or directory. May 15 15:43:46 <hostname> login: load_modules: cannot open module /usr/lib/security/pam_mkhomedir.so.1 But /usr/lib/pam_mkhomedir.so.1 does not exist, and it does not exist on my other servers, but those zones are accessible using zlogin. I can only zlogin to the zones with zlogin -S ZONENAME. What to do next? Thank you.

  Read the article

• EEE PC Keyboard malfunctioning - Ctrl key "sticks" after 10 seconds

  - by DWilliams

  I was given a EEE PC belonging to a friend of a friend to fix. The keyboard did not appear to work at all. I spent a while testing out various things, blowing the keyboard out, checking for damage, and so on. Nothing appeared to be physically wrong. At first I noticed that the keyboard appeared to work just fine for 10 seconds (on average, sometimes more sometimes less) after being powered on. It had been restored to the factory default xandros installation with no user set up, so I couldn't get in to mess with things since I couldn't type to make a user. I made an ubuntu live USB to boot it from, and managed to get the boot order changed to boot from USB in the ~10 seconds of working keyboard I had (I don't think I've ever had to rush around BIOS menus that quickly). After I got Ubuntu up on it, I played around a bit more and determined that apparently the ctrl key is stuck down (not literally, but it's on all the time). If I open gedit, pressing the "o" key brings the open dialog, "s" opens the save dialog, and all other behaviour you would expect to see if you were holding down the control key. The only exception that I noticed is the "9" and "0" keys. They function normally. Figuring that out I made a xandros user with a name/password consisting of 9's and 0's. I couldn't find any options in Xandros that could potentially be helpful. I'm not familiar with EEE PCs. Is it safe to assume that the keyboard is simply dead or could there be another problem? I don't want to purchase another keyboard for him if that isn't going to fix the problem. The netbook doesn't show any obvious signs of damage but the owner is a biker and very often has it with him on the road so it's been subjected to a good bit of vibration.

  Read the article

• Authenticating Linked Servers - SQL Server 8 to SQL Server 10

  - by jp2code

  We have an old SQL Server 2000 database that has to be kept because it is needed on our manufacturing machines. It also maintains our employee records, since they are needed on these machines for employee logins. We also have a newer SQL Server 10 database (I think this is 2008, but I'm not sure) that we are using for newer development. I have recently learned (i.e. today) that I can link the two servers. This would allow me to access the employee tables in the newer server. Following the SF post SQL Server to SQL Server Linked Server Setup, I tried adding the link. In our SQL Server 2000 machine, I got this error: Similarly, on our SQL Server 10 machine, I got this error: The messages, though worded different, probably say the same thing: I need to authenticate, somehow. We have an Active Directory, but it is on yet another server. What, exactly, should be done here? A guy HERE<< said to check the Security settings, but did not say what else to do. Both servers are set to SQL Server and Windows Authentication mode. Now what?

  Read the article

• CDROM does not appear on desktop, MACOS 10.5.7

  - by Cheeso

  When I pop a CDROM into the drive of my Macbook Pro, It spins up, I hear it, but no icon appears on the desktop. (I think it's 10.5.7; actually not sure how to verify this on Mac, but I think I saw a 10.5.7 flash by somewhere). In the finder preferences, I have "Show these items on the Desktop" set to show HDs, External Disks, and CDs, DVDs, and ipods. All three of those are checked. I do see the internal HD on the desktop. In Disk utility I can see the CD/DVD hardware. It says "MATSHITA DVD-R UJ-857E...". From Disk Utility I can eject the drive. But in Finder, there is never a CD/DVD listed under "Devices". When I insert a disk, nothing happens, I cannot see it. I also cannot boot from bootable CDROMs by holding C down . Suggestions? I am not very experienced with Mac; I have used Windows for years. EDIT Two updates: I saw this article on support.apple.com, and modified the hostconfig appropriately. It did not have the AUTODISKMOUNT entry, so I added one, rebooted. Same behavior. It does not see the CDROM in Finder, does not mount it on desktop. I put an old manufactured CDROM into the drive, and voila! it showed up on the desktop. The CD that does not appear is a GNome Partition Editor Live CD, which I guess is based on debian. That CD boots in other (non-Mac) PCs. I want to use this to adjust the Bootcamp partition. Suggestions?

  Read the article

• linux hardware raid 10 / lvm / virtual machine partition alignment and filesystem optimization

  - by Jason Ward

  I've been reading everything I can find about partition alignment and filesystem optimization (ext4 and xfs) but still don't know enough to be confident in setting up my current configuration. My remaining confusion comes from the LVM layer and if I should use raid parameters on the filesystem in guest os'es. My main questions are: When I use 'pvcreate --dataalignment' do I use the stripe-width as calculated for a filesystem on RAID (128kB for ext4 in my situation), the Stripe size of the RAID set (256kB), something else altogether, or do I not need this? When I create ext2/3/4 or xfs filesystems in guests on the Logical Volumes, should I add the settings for the underlying RAID (e.g. mkfs.ext4 -b 4096 -E stride=64,stripe-width=128)? Does anyone see any glaring errors in my set up below? I'm running some benchmarks now but haven't done enough to start comparing results. I have four drives in RAID 10 on a 3ware 9750-4i controller (more details on the settings below) giving me a 6.0TB device at /dev/sda. Here is my partition table: Model: LSI 9750-4i DISK (scsi) Disk /dev/sda: 5722024MiB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1.00MiB 257MiB 256MiB ext4 BOOTPART boot 2 257MiB 4353MiB 4096MiB linux-swap(v1) 3 4353MiB 266497MiB 262144MiB ext4 4 266497MiB 4460801MiB 4194304MiB Partition 1 is to be the /boot partition for my xen host. Partition 2 is swap. Partition 3 is to be the root (/) for my xen host. Partition 4 is to be (the only) physical volume to be used by LVM (for those who are counting, I left about 1.2TB unallocated for now) For my Xen guests, I usually create a Logical Volume of the needed size and present it to the guests for them to partition as needed. I know there are other ways of handling that but this method works best for my situation. Here's the hardware of interest on my CentOS 6.3 Xen Host: 4x Seagate Barracuda 3TB ST3000DM001 Drives (sector size: 512 logical/4096 physical) 3ware 9750-4i w/BBU (sector size reported: 512 logical/512 physical) All four drives make up a RAID 10 array. Stripe: 256kB Write Cache enabled Read Cache: intelligent StoreSave: Balance Thanks!

  Read the article

• Juniper’s Network Connect ncsvc on Linux: “host checker failed, error 10”

  - by hfs

  I’m trying to log in to a Juniper VPN with Network Connect from a headless Linux client. I followed the instructions and used the script from http://mad-scientist.us/juniper.html. When running the script with --nogui switch the command that gets finally executed is $HOME/.juniper_networks/network_connect/ncsvc -h HOST -u USER -r REALM -f $HOME/.vpn.default.crt. I get asked for the password, a line “Connecting to…” is printed but then the programm silently stops. When adding -L 5 (most verbose logging) to the command line, these are the last messages printed to the log: dsclient.info state: kStateCacheCleaner (dsclient.cpp:280) dsclient.info --> POST /dana-na/cc/ccupdate.cgi (authenticate.cpp:162) http_connection.para Entering state_start_connection (http_connection.cpp:282) http_connection.para Entering state_continue_connection (http_connection.cpp:299) http_connection.para Entering state_ssl_connect (http_connection.cpp:468) dsssl.para SSL connect ssl=0x833e568/sd=4 connection using cipher RC4-MD5 (DSSSLSock.cpp:656) http_connection.para Returning DSHTTP_COMPLETE from state_ssl_connect (http_connection.cpp:476) DSHttp.debug state_reading_response_body - copying 0 buffered bytes (http_requester.cpp:800) DSHttp.debug state_reading_response_body - recv'd 0 bytes data (http_requester.cpp:833) dsclient.info <-- 200 (authenticate.cpp:194) dsclient.error state host checker failed, error 10 (dsclient.cpp:282) ncapp.error Failed to authenticate with IVE. Error 10 (ncsvc.cpp:197) dsncuiapi.para DsNcUiApi::~DsNcUiApi (dsncuiapi.cpp:72) What does host checker failed mean? How can I find out what it tried to check and what failed? The HostChecker Configuration Guide mentions that a $HOME/.juniper_networks/tncc.jar gets installed on Linux, but my installation contains no such file. From that I concluded that HostChecker is disabled for my VPN on Linux? Are the POST to /dana-na/cc/ccupdate.cgi and “host checker failed” connected or independent? By running the connection over a SSL proxy I found out that the POST data is status=NOTOK (Funny side note: the client of the oh-so-secure VPN does not validate the server’s SSL certificate, so is wide open to MITM attacks…). So it seems that it’s the client that closes the connection and not the server.

  Read the article

• Replacing HD in an MacOS 10.6.8 server caused all shares to fail

  - by Cheesus

  I'm hoping someone might have a helpful suggestion about this problem. We have 2 MacOSX servers available for file sharing. (quad Xeons - 2GB RAM, both 10.6.8), No.1 is an Open Directory Master with 50+ user accounts, No.2 has only 2 local accounts (/local/Default) and looks at the OD Master for all user accounts (/LDAPv3/10.x.x.20/) Both servers have 3 internal HD's, The boot volume with only Server OS and minimal Apps. A 'DataShare' HD (500GB) and a backup drive (500GB). After upgrading the DataShare HD in Server No.2 from a small internal HD (500GB) to larger capacity (2TB) drive, users are unable to connect to shares on Server No.2. Users get an error "There are no shares available or you are not allowed to access them on the server" The process I followed was to use Carbon Copy Cloner to create an exact copy of the original data drive (keeps all ownership data, UID, permissions, last edit date and time). Everything booted up ok, no indication there was any issues. (Paths to the sharepoint look good) Notes during troubleshooting - Server1 is operating perfectly, all users can access shares and authenticate etc. - I've checked the SACL (Server Access Control List) settings is ok. - On Server2 in the Server Admin' app, I can see all the shares listed ok. The paths seem valid, I can disable / reenable the shares, no errors. - On Server2 'workgroup manager' lists all the accounts from the OD Master in the LDAP dir view. All seems fine from here. Basically everything looks normal but no file shares on Server2 can be accessed from regular users.

  Read the article

• Three native monitors on Dell OptiPlex 9010

  - by matthewk

  http://www.dell.com/uk/business/p/optiplex-9010/pd says: Configure your workspace the way you want it with support for up to three native monitors via DP/DP/VGA ports. So I ordered one, and have connected three monitors, but I can only enable two at a time. It can be both of the ones connected by DisplayPort, or one of the ones connected by DisplayPort and the one connected by VGA. Does anyone know whether it really is possible to enable all three at once, and if so, how?

  Read the article

• Make Dell's OpenManage 6.2 information available through SNMP

  - by tronda

  I have successfully installed OpenManage on a CentOS 5.4 server and I'm able to use OpenManage through the web interface running on port 1311, but I would like to be able to expose this information through the SNMP server. I don't know SNMP particularly well so the configuration is a result of trial and error. I've tried to follow the description pointed out in the Open Manage Server Administrator User Guide. I've followed the documentation regarding SNMP configuration, but without success. I've created a small snmpd.conf file: com2sec notConfigUser default public group notConfigGroup v1 notConfigUser group notConfigGroup v2c notConfigUser view systemview included .1.3.6.1.2.1.1 view systemview included .1.3.6.1.2.1.25.1.1 access notConfigGroup "" any noauth exact all all none view all included .1 rwcommunity public 10.200.26.50 syslocation "Somewhere" syscontact [email protected] pass .1.3.6.1.4.1.4413.4.1 /usr/bin/ucd5820stat smuxpeer .1.3.6.1.4.1.674.10892.1 When I try to fetch SNMP information by using snmpwalk I get the following output: SNMPv2-MIB::sysDescr.0 = STRING: Linux myserver.test.com 2.6.18-164.15.1.el5 #1 SMP Wed Mar 17 11:30:06 EDT 2010 x86_64 SNMPv2-MIB::sysObjectID.0 = OID: NET-SNMP-MIB::netSnmpAgentOIDs.10 DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (1180389) 3:16:43.89 SNMPv2-MIB::sysContact.0 = STRING: [email protected] SNMPv2-MIB::sysName.0 = STRING: myserver.test.com SNMPv2-MIB::sysLocation.0 = STRING: "Somewhere" SNMPv2-MIB::sysORLastChange.0 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORID.1 = OID: SNMPv2-MIB::snmpMIB SNMPv2-MIB::sysORID.2 = OID: TCP-MIB::tcpMIB SNMPv2-MIB::sysORID.3 = OID: IP-MIB::ip SNMPv2-MIB::sysORID.4 = OID: UDP-MIB::udpMIB SNMPv2-MIB::sysORID.5 = OID: SNMP-VIEW-BASED-ACM-MIB::vacmBasicGroup SNMPv2-MIB::sysORID.6 = OID: SNMP-FRAMEWORK-MIB::snmpFrameworkMIBCompliance SNMPv2-MIB::sysORID.7 = OID: SNMP-MPD-MIB::snmpMPDCompliance SNMPv2-MIB::sysORID.8 = OID: SNMP-USER-BASED-SM-MIB::usmMIBCompliance SNMPv2-MIB::sysORDescr.1 = STRING: The MIB module for SNMPv2 entities SNMPv2-MIB::sysORDescr.2 = STRING: The MIB module for managing TCP implementations SNMPv2-MIB::sysORDescr.3 = STRING: The MIB module for managing IP and ICMP implementations SNMPv2-MIB::sysORDescr.4 = STRING: The MIB module for managing UDP implementations SNMPv2-MIB::sysORDescr.5 = STRING: View-based Access Control Model for SNMP. SNMPv2-MIB::sysORDescr.6 = STRING: The SNMP Management Architecture MIB. SNMPv2-MIB::sysORDescr.7 = STRING: The MIB for Message Processing and Dispatching. SNMPv2-MIB::sysORDescr.8 = STRING: The management information definitions for the SNMP User-based Security Model. SNMPv2-MIB::sysORUpTime.1 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.2 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.3 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.4 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.5 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.6 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.7 = Timeticks: (0) 0:00:00.00 SNMPv2-MIB::sysORUpTime.8 = Timeticks: (0) 0:00:00.00 I suspect that I should get some DELL specific information when I use the snmpwalk utility. Is there a configuration in snmpd.conf file which is wrong, or do I have to configure on the OpenManage side in order to get the hardware information accessible from SNMP?

  Read the article

• Dell R510 can i go from E5620 to X5690

  - by NJinPHX

  I have a Dell R510 used for a SQl server. Can I go from E5620 to X5690? They are both in the same Intel Xeon 5600 series. But the i did not know if a X (Performance) is interchangeable E (Mainstream). If not then the fastest upgrade i can make will be to another E. thx Intel® Xeon® Processor E5620 (Current) http://ark.intel.com/products/47925 Intel® Xeon® Processor X5690 (Proposed Upgrade) http://ark.intel.com/products/52576 Intel® Xeon® Processor E5649 (Fall back Upgrade) (cant post link)

  Read the article

• Dell Poweredge 2650 RAC Issue

  - by Ryanteck

  I just got a second hand Dell Poweredge 2650 and its working fine. I can access the embedded remote access controller via the Racadm.exe tool (Under wine) but the web based version of it (Which I would prefer to use) has an SSL certificate error. I select continue I know there are risks ect and java starts up. It then gives me the error failed to validate certificate the application will not be executed Is there any way to be able to fix this? *Update Full java error output @ http://paste.ubuntu.com/6352862/

  Read the article

• Dirty Cache Dell Equallogic Storage Array

  - by Jermal Smith

  has anyone ever run into a dirty cache issue with a Equallogic SAN. Even after replacement of the controller cards in the Equallogic Storage Array fails offline with a dirty cache. I have listed steps here on my blog to bring the SAN online again, however this is not the best solution as it continues to fail. http://jermsmit.com/dirty-cache-dell-equallogic-storage-array/ If you have any info on this please share. Thanks, Jermal

  Read the article

• Dell PowerEdge Server BitLocker Hotswap Hard disks

  - by JoshODBrown

  We have a Windows 2008 R2 Server running on a Dell PowerEdge R310 Server with Bitlocker enabled. There are two physical Hard disks configured as RAID 1. One of the disks recently started having an issue, so we have now have a warranty covered replacement for it, But we were curious if there will be any issues hot swapping the new drive in due to BitLocker being enabled? Has anyone had a similar experience with scenario?

  Read the article

• Dell inspiron 1525 laptop won't boot up.

  - by Becca

  It comes to a page called "Dell Media Direct" and then loads another page where it says "A problem has been detected and windpws has been shut down to prevent damage to your computer." then it has a bunch of info about why it may be the cause. can someone please help?

  Read the article

• Dell Precision 670 Disk Mirroring

  - by user39325

  Hi, i have a Dell Precision 670 server with SCSI disk drives, i have a 74 gb disk and I want to add another 74 gb to make disk mirroring. Any suggestions. I am using it for ubuntu 8.04

  Read the article

• White lines appear right in the middle of my Dell XPS M1210 screen

  - by ymasood

  My Dell XPSM1210 has developed these weird lines right in the middle of the screen. When I connect an external monitor the lines disappear and the display is fine. I would like to know if this is a problem with the screen panel and if it needs replacement is there a place where I could buy one. This laptop is not under warranty so I'm willing to get the screen replaced. Thanks in advance!

  Read the article

< Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >