Search Results

Search found 30311 results on 1213 pages for 'dont ask ubun'.

Page 46/1213 | < Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >

• Huawei E3276 LTE uplink slow in the routing Ubuntu, but not with other devices in the LAN

  - by Mytomi

  I have a Huawei E3276 LTE dongle (12d1:14fe - 12d1:1506) and a problem with the upstream speed. The problem is not only present with Ubuntu 14.04 LTS (64 bit workstation, kernel 3.16), but also with Raspbian Jessie for Raspberry PI (kernel 3.14). Upstream seems to be always limited to 5 Mbit/s whenever I check the speed from the Linux computer that I use as a LTE router. The other computers in the LAN always get about 10-15 Mbit/s upstream, even though the traffic is routed through the same Linux computer suffering from seemingly capped uplink. Downstream speed is always fine, 25 Mbit/s. I even installed Windows 7 in the same computer as Ubuntu and the speeds are 25 Mbit/s down, 15 Mbit/s up. So the problem is not with E3276 device itself or in the mobile subscription, but in the Huawei E3276 Linux compatibility. Maybe something in the kernel? I have made sure that the matter is not with iptables rules: the speed does not noticeably increase when iptables is disabled. Turning off IPv4 forwarding does not improve speed either. I'm not sure what settings and logs do help in debugging the situation. Please ask for more details, if you have a clue what might be wrong. Thanks, Mytomi

  Read the article

• Spinup time failure

  - by bioShark

  I am not sure this is a real question or a bug I should report Ubuntu. Using: Ubuntu 11.10, on a Intel Q6600, Samsung Spinpoint F4 2TB. I have set my PC on Suspend and after I came back, pressed Enter and after logging in everything was back to normal. However, I had a message from Disk Utility that one disk reports errors. I entered Disk Utility, and my Samsung 2TB disk, the one on which my Ubuntu is installed, had the SMART Status turned red, with error message on it. The error was: Spinup time failed Value 21, Threshold value was 25 (so the error was reported because 21 < 25) I restarted and booted up in Windows to see what HD Tune is reporting. Unfortunately it was exactly the same 21/25. After reading up on Wiki about SMART and the errors, I discovered that Spinup time is the time required for the disk to reach full spinning speed in milliseconds. Then it hit me that, in Ubuntu I had Suspended the system, making essentially all my hardware stop. And when I rebooted to Windows, the hardware doesn't really stop, so SMART's reading of the Spinup time was still from Ubuntu's suspension. So I did a full PC stop and then booted up again, both in Ubuntu and Windows to see if there are different readings. Both reported successful Spinup time, 68 (a little better then 21 :) ), although in Disk Utility I have a nice message: Failed in the Past So now I am pretty sure that Ubuntu didn't handle the Suspend correctly, but then again should I worry about Imminent hardware failure ? Am I missing some drivers? Should I report this as a bug to Ubuntu? Sorry if this was a bad place to ask this question.

  Read the article

• OS X Mavericks Won't Connect To Ubuntu Server (Netatalk, Avahi)

  - by Andy Ibanez

  I'm really sorry for posting this. I know it may have been asked a thousand times. I have googled like crazy and I'm on the verge of desperation here. Basically, I followed this guide: http://motionsoundfx.com/2012/05/ubuntu-vnc-afp-macosx/ To create a small personal file server. When I installed it, I was able to connect to it just fine, I connected with my Ubuntu username and password and I was able to see the home directory. But later, I had to restart the file server so I could prepare a couple of other hard drives to put in. When the server restarted, I tried to connect to it, but I got an error message on my Mac: "The version of the server you're trying to connect to is not supported. Please contact your system administrator to solve this problem." Again, I have googled like crazy for this, and everybody says it is a problem with OS X Lion and up (assuming it affects Mavericks too). I have tried all the fixes mentioned for Lion and Mountain Lion and I haven't had any luck. That's the reason I'm posting this here: I suspect the problem is with my Ubuntu server. This happened after I restarted the server. Before restarting the server, I just put in my credentials and saw my home directory. Something when I restarted the server must have been messed up. I have found some other solutions, including to use "SHX2" in the conf file, but it hasn't worked for me. I ask for your help to solve this issue. Also please understand I'm completely illiterate when it comes to Linux. This is a nice chance to me to learn the OS so please give me detailed steps to do things if you deem it necessary. Thank you! I'm using Ubuntu Server 13.10 (the latest one as of today).

  Read the article

• Partitioning a hard drive before install

  - by yohbs

  I have a new ASUS laptop that I got from the university. The guys at the computing centre recieved it before me, erased the hard disk, and installed all their crappy software (Novel, outlook, and the like). I tried to install Ubuntu with dual boot, but because they apparently did whatever it is they did wrong, and the installer does not recognize the existing windows installation and only suggests to install Ubuntu as a sole OS. None of the advices here or here helped. My final decision is to indeed let Ubuntu erase all existing windows stuff (and then use windows occasionally through VirtualBox). However, when I try to do that it tells me that the partitioning looks like GPT but doesn't have the correct signatures, or something like this. It asks whether this is indeed a GPT HD, and I don't know what to tell it. What I ask is: should I simply use gparted from the CD to repartition the HD? If so, what would be the recommended partitioning (I have 750GB), and the recommended filesystem (ext3? ext4?). Update: here's a screen shot Thanks in advance for any advice.

  Read the article

• File saving disabled 'Saving has been disabled by system admin'

  - by Gubuntu

  I have coded my own html website recently, and today wished to add a Google calender object to it. I have not put this website on the web because it is for my own personal use and I can't buy a domain. So I just have a folder on my pc that I load the index.html from now and then. As I was saying, today I got an error while trying to save the Google calender object in. I am system admin on my PC, in fact no one else uses but me, except when I have friends round, but for once my PC seems to think I'm some standard account user, because I couldn't save. I thought of clicking close and seeing if it came up with save as, but it didn't, it said 'Are you sure you want to close without saving?' or something along the lines of that, and 'Saving has been disabled by your system admin.' I couldn't do anything. I tried looking at the settings of the file, and it had me as read only in one of the selections, so I changed that to read & write, but to no avail. I did not save as root when I last edited the file, so I don't get what's going on. Help! P.S. This is on Ask Ubuntu not Superuser because it is on my Ubuntu PC and it appears to be a problem with Ubuntu not root or hardware.

  Read the article

• Burned CD-R are not identical to the input iso image, why?

  - by Grumbel

  I have the issue that sometimes when I burn an iso image to a CD-R with: sudo wodim -v driveropts=burnfree -data dev=/dev/scd0 input.iso And then read it back out again with: sudo dd if=/dev/cdrom of=output.iso dd: reading `/dev/cdrom': Input/output error ... That I end up with two iso images that are not identical, namely the output.iso is missing 2048 bytes at the end. When I however mount the iso image or CD-R and compare the actual files on the mountpoint, both are identical. Is that expected behavior or is that an actually incorrect burn of the data? And if its expected, how can I verify that the burn process was successful? The reason why I ask in the first place is that it seems to be reproducible behavior, certain iso images come out 2048 bytes short, even on repeated burns, but all burned CD-Rs are under themselves identical. Also what is the reason behind the: dd: reading `/dev/cdrom': Input/output error As it happens always, I assume it is normal, but what is the technical reason behind it? I assume CDs don't allow the device to detect the size directly, so dd reads till it encounters the end the hard way. Edit: User karol on superusers.com mentioned that both the size issue and the read error are the result of using -tao (default) in wodim instead of -dao mode. I couldn't yet test it, but it sounds like the most plausible explanation so far.

  Read the article

• Only 1080p youtube videos work properly

  - by oshirowanen

  I have Ubuntu 12.04 64bit installed/full updated and have noticed that I can only play 1080p youtube videos properly on full screen. All other resolutions, 480, 720, 1440 etc do not go into full screen properly. Please have a look at the attached images. You will notice that only the 1080p video has the video control bar right at the bottom with a respectable text size. All other videos don't have the video control bar right at the bottom on the screen, and the control bar text is too small. I've had this problem for ages, but finally decided to ask about it. 480p: Notice the bottom control bar, it's not at the bottom on the screen and the video has borders on the sides: 720p: Notice the bottom control bar, it's not at the bottom on the screen and the video has borders on the sides and the text is tiny: 1080p: This is the only one that works as expected, i.e. controls right at the bottom, and good font size and no borders on the sides: 1440p: Notice the bottom control bar, it's not at the bottom on the screen and the video has borders on the sides: How do I correct this problem so I can play all different video resolutions at full screen. The flash version I have installed in Chromium is Adobe Flash Player - Version: 11.2 r202 - Shockwave Flash 11.2 r202

  Read the article

• Commands don't have permission when using absolute path

  - by Markos

  I have folders set up this way: /srv/samba/video getfacl /srv/samba/video # file: srv/samba/video # owner: root # group: nogroup user::rwx group::--- group:sambaclients:rwx group:deluge:rwx mask::rwx other::--- default:user::rwx default:group::--- default:group:sambaclients:rwx default:group:deluge:rwx default:mask::rwx default:other::--- That means, user deluge has rwx to folder /srv/samba/video. However, when running command as user deluge, I am getting weird permission errors. When in folder /srv/samba/video: sudo -u deluge mkdir foo works flawlessly. But when using absolute path: sudo -u deluge mkdir /srv/samba/video/foo I am getting permission denied. When running sudo -u deluge id, I get output uid=113(deluge) gid=124(deluge) skupiny=124(deluge) which shows that user deluge is indeed in group deluge. Also, the behavior was the same when I gave the permissions also to user deluge not just group deluge. When executing as non-system user, it does work. The reason that I want to use absolute paths is that I am using automatically triggered post-download script which extracts some files into the folder. I have spent way too many hours to solve this problem myself. mkdir isn't the only command that fails, touch is doing the same thing, so I suspect that it's not mkdir's fault. If you need more info, I will try to put it in here, just ask. Thanx in advance. Edit: It seems that the root of the problem is acl set on perent folder /srv/samba, which indeed does not grant permissions to deluge (but neither denies it). getfacl /srv/samba # file: srv/samba # owner: root # group: nogroup user::rwx group::--- group:sambaclients:rwx mask::rwx other::--- default:user::rwx default:group::--- default:group:sambaclients:rwx default:mask::rwx default:other::--- If I grant the permission also to this folder, it suddenly starts to work so I believe that the acl on /srv/samba is somehow denying the permissions to deluge. So the question is: how do I set acl to both /srv/samba and /srv/samba/video so that sambaclients have access to whole /srv/samba and subdirectories and deluge has access only to /srv/samba/video and subdirectories?

  Read the article

• What is the way to submit a patch to fix all the damage that LP: #600941 causes?

  - by nutznboltz

  What is the best way to submit a patch to fix all the damage that LP: #600941 causes? I ask because LP: #600941 was put into every version of Ubuntu still supported at this time. Should I pick a particular version and run ubuntu-bug on it? Should that version be the LTS or Oneiric or Precise (how can I get Precise if I need it?) The story is that after it was pushed out all of our systems started experiencing Nagios nrpe restart failures. Commands like /etc/init.d/nagios-nrpe-server restart would cause nrpe to stop but not restart. I tracked this down to the way that the /etc/init.d/nagios-nrpe-server script is calling start-stop-daemon. The issue is that the "stop" stanza in the /etc/init.d/nagios-nrpe-server script first calls start-stop-daemon which sends SIGTERM to nrpe and then waits only for one second. If nrpe has not exited by that time the pid file will still exist and the /etc/init.d/nagios-nrpe-server script will remove it. Worse if /etc/init.d/nagios-nrpe-server restart is used not only will the pid file be removed, the attempt to restart nrpe will fail provided that the nrpe daemon is still tardy in shutting down. The attempt to start under those circumstances will fail because nrpe will still be bound to a socket and the second attempt at binding will cause the nrpe startup to abort. They should have wondered why there was a comment about "sometimes the pid file does not get removed". They should have tested on systems that have a heavy load and therefore slow nrpe response times. The fix is to add --retry 10 or such to the invocation of start-stop-daemon ... --stop ... Thanks

  Read the article

• Very slow write access to SSD disks on some Asus P8Z77 motherboards

  - by lenik

  I have Asus P8Z77-V LK motherboard, that ran Mint 13 (based on Ubuntu 12.04) just perfectly, but recently I've tried to install Mint 17 and noticed abysmal write performance. Write speed on SSD disk was about 1.5MB/sec, when it's supposed to be in 150-250MB/sec range. For write testing I've used dd if=/dev/zero of=/dev/sda bs=10M count=10 while booted up from LiveCD. I have also tested the read speed with hdparm -tT /dev/sda and got about 440MB/sec -- that's normal. I can tell, the read performance has not degraded at all and is not an issue here. Since I had a few different SSD disks and few motherboards, I've tested and tested and here are results: Asus P8H77 works fine with Mint13, has very slow write speed starting from Mint14. Asus P8Z77-V LK works with Mint13, has very slow write speed starting from Mint14. Asus P8Z77-V PRO works with Mint13, and works just fine with Mint14, 15, 16 and 17. The only difference between "PRO" version and others is that it has extra SATA controller onboard (in addition to the Z77 chipset SATA controller) providing extra 2 SATA ports. SSD disks work fine with "PRO" version when connected to the native SATA ports as well as to the ports provided by extra SATA controller, so this does not look like a hardware issue. As far as I can tell, there's something changed in the kernel while going from 3.2 to 3.5, that affects the detection of onboard SATA controller for Asus P8*77 motherboards, that screws up the write speed for SSD drives. Could anyone shed some light on how to fix this issue or, possibly, give a pointer to a more suitable place to ask this question?

  Read the article

• format/build raid 5 with one 4k drive, three 512b

  - by skidawgz

  I have 4 WD 1TB drives which I want to 4x1TB Raid5. I am not sure what course of action to take next. How do I configure my 4th drive (sde) to align with the rest? Will this affect performance? I rcv this msg (which brings me here to ask these question): The device presents a logical sector size that is smaller than the physical sector size. Aligning to a physical sector (or optimal I/O) size boundary is recommended, or performance may be impacted. fdisk -l shows: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf324ba09 Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x38bcc1f0 Device Boot Start End Blocks Id System /dev/sdc1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x570f77e7 Device Boot Start End Blocks Id System /dev/sdd1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xeb665e7b Device Boot Start End Blocks Id System

  Read the article

• "Failed to create swap space" error during installation

  - by Welsh Heron

  I've been trying to install Ubuntu for the past two days or so, but I've been running into a problem: every time I run the installation program on the LiveCD, I always get the same (or a very similar) error: "Failed to create Swap space The creation of swap space in partition #3 of SCSI5 (0,0,0)(sda) failed." So far, I've run DBAN (Darik's Boot and Nuke) on my HDD once, to make absolutely sure that everything on it had been erased. Then, I simply put in the LiveCD, and let it run the automated install. I get the above error directly after I tell it to automatically partition the HDD (it will work for a second or so, then this will pop up), forcing me back to the screen that lets me choose whether I want to automatically or manually partition the HDD. Well, after failing to install the software manually, I did a little research and learned enough about partitioning Linux to use the 'Manual partitioning' option. I partitioned the HDD as follows (it's a 1TB drive): /home - (the rest)- ext2, / - 20GB - ext2, /boot - 100MB - ext2, /swap - 8GB /EFIboot - 40MB The only difference when I tried this method was that I got THIS message: "Failed to create Swap space The creation of swap space in partition #2 of SCSI5 (0,0,0)(sda) failed." Basically, the only difference was that there was now a '2' instead of a '3'. If I may ask, what exactly am I doing wrong? I've tried looking around the internet (that's basically all I've done for the last two days), but no one seems to have the same problem that I have, and I've tried most of the solutions for similar problems (DBAN, formatting partitions in ext2 format, etc). The only thing I haven't tried is using the terminal to manually partition the HDD...and I actually DID try to do this, but I wasn't able to get past 'su' 's password demand, so I wasn't able to use the terminal. Thank you for your help in advance. ~Welsh

  Read the article

• How do I connect to my running VM via virsh?

  - by Avery Chan

  My VM has already been started via virsh start chameleon.ootbdev. When I do a virsh console chameleon.ootbdev I get the following output: Connected to domain chameleon.ootbdev Escape character is ^] error: internal error cannot find character device (null) Doing a google search on this led me to this "solution". Unfortunately, editing the domain via virsh edit chameleon.ootbdev doesn't seem to stick. I suspect the issue is that I'm inserting the XML incorrectly: the instructions from the link ask me to insert the following XML into the domain XML file. <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> I've posted my domain XML file to pastebin here. This is AFTER I've tried to insert the above XML. I inserted this XML after the </devices> block. My primary question is: How do I connect to the running VM? A secondary question would be: How do I edit the domain file with the above XML and get the changes to stick?

  Read the article

• How to use the Nautilus search option

  - by Luis Alvarado

  In Nautilus if I press CTRL+F I get a search box that helps me search in the current directory and sub directories for specific names, but what if I want to: Find ALL files (including files without extensions) Find a file without an extension (Without the dot symbol or without any other name/extension separator) Find a file with/without a special character Find all files that start/not start with a character Find all files that end/not end with a character Find all files that start/no start with a character but end/not end with a character Find only files/folders Find files with specific text in them Find files with less/more/equal than/to X size Find files modified/created in X date All of this searches in the Nautilus search box I mentioned before. I ask this since the KDE's search is much better in this and gives pretty good freedom in searching for virtually anything, so I might not be learning how to use the Nautilus search option correctly. Note that I am talking about the first search done since some of this options show AFTER a search is done so the user can narrow it down more by doing a more specific search inside the Search results (for the first search). I am asking here how to do any of the search options I mentioned above in the first search.

  Read the article

• Booting sequence. Ubuntu 12.04 installation and cohabitation with former OSes

  - by Stephane Rolland

  I am on the brink of installing Ubuntu 12.04 Precise Pengolin on the first primary partition of my hard-drive. (A day in History for me since I had always kept a MS windows at this first place). But I have some fears: This is my last computer available (In the past I used to have 2 or even 3 machines so I could always un/plug HDs for recovery operations and rescue) The current booting sequence is not straight forard. So as to explain the boot sequence let me briefly sum-up the history of this laptop computer. It was a dedicated Windows Vista computer. 1st and only Primary partition. Then I added Windows 7 (on the 2nd primary partition) letting the Windows Vista Boot Loader manage the boot sequence. Then I added Ubuntu 10.04 Lucid Lynx on the 1st sub-partition of the Extended Partitionm asking Grub to be the boot loader. But when I ask Grub to launch windows it launches the Vista BootLoader that manages the choice betzeen Vista and 7. So in theory Grub is on the MasterBootRecord - though I understand where the Vista BootLoader remains. Now, I will no longer use the Ubuntu 10.04 ( on extended partition) and also the Windows vista (on the first primary partition). I will install Ubuntu 12.04 on the First Primary, asking it to install a new bootloader. I want to keep the Windows 7 that is already on the Second Primary partition. And I want it to be loaded by the Ubuntu Boot loader(I don4t knoz zhich is included in this version)... And I am afraid the last point will not work.

  Read the article

• Nautilus crashes after Ubuntu Tweak Package Cleaner

  - by Ka7anax

  Few days ago I started having some problems with nautilus. Basically when I'm trying to get into a folder it crashes. It's not happening all the time, but in 85% it does... Sometimes, after the crash all my desktop icons are also gone. The only thing that I think causes this is Ubuntu Tweak - I'm not sure, but the issues started after I did the Package cleaner from Ubuntu Tweaks... Any ideas? -------- EDIT ---------- First time, after running the command (nautilus --quit; nautilus --no-desktop) 3 times all the system crashed (except the mouse, I could move the mouse). After restart I run it and obtain this: ----- Initializing nautilus-gdu extension Initializing nautilus-dropbox 0.6.7 (nautilus:2966): GConf-CRITICAL **: gconf_value_free: assertion value != NULL' failed (nautilus:2966): GConf-CRITICAL **: gconf_value_free: assertionvalue != NULL' failed Nautilus-Share-Message: Called "net usershare info" but it failed: 'net usershare' returned error 255: net usershare: cannot open usershare directory /var/lib/samba/usershares. Error No such file or directory Please ask your system administrator to enable user sharing. and then this: cristi@cris-laptop:~$ nautilus --quit; nautilus --no-desktop (nautilus:3810): Unique-DBus-WARNING **: Error while sending message: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.

  Read the article

• Cannot install openjdk on Hardy Heron

  - by infaustus

  I know that Hardy Heron is very old but don't ask why Hardy... I've tried root@vz10931:/etc/apt# apt-get install openjdk-6-jre Reading package lists... Done Building dependency tree Reading state information... Done You might want to run `apt-get -f install' to correct these: The following packages have unmet dependencies: openjdk-6-jre: Depends: libasound2 (> 1.0.14) but it is not going to be installed Depends: libgif4 (>= 4.1.6) but it is not going to be installed Depends: libxtst6 but it is not going to be installed Depends: openjdk-6-jre-headless (>= 6b18-1.8.3-0ubuntu1~8.04.2) but it is not going to be installed vim: Depends: vim-common (= 1:7.1-138+1ubuntu3.1) but 2:7.3.154+hg~74503f6ee649-2ubuntu3 is to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). My sources.list deb http://pl.archive.ubuntu.com/ubuntu/ hardy main restricted universe multiverse deb-src http://pl.archive.ubuntu.com/ubuntu/ hardy main restricted universe multiverse deb http://pl.archive.ubuntu.com/ubuntu/ hardy-updates main restricted universe multiverse deb-src http://pl.archive.ubuntu.com/ubuntu/ hardy-updates main restricted universe multiverse deb http://security.ubuntu.com/ubuntu hardy-security main restricted universe multiverse deb-src http://security.ubuntu.com/ubuntu hardy-security main restricted universe multiverse And root@vz10931:/etc/apt# ls -l sources.list.d/ total 0 Please help. When I've tried apt-get install -f I had install new system because everything crashed. Edit: I checked that i have openjdk installed root@vz10931:/var/www/mailer# dpkg --list | grep java iU sun-java6-bin 6.24-1build0.8.04.1 Sun Java(TM) Runtime Environment (JRE) 6 (ar iU sun-java6-jdk 6.24-1build0.8.04.1 Sun Java(TM) Development Kit (JDK) 6 iU sun-java6-jre 6.24-1build0.8.04.1 Sun Java(TM) Runtime Environment (JRE) 6 (ar but when i am trying to start java file: java -jar program.jar error appear -bash: java: command not found

  Read the article

• 12.04 No Sound - ALC888 / Radeon 3200HD

  - by Ross

  Evening all. I have a MSI U230 netbook, MV40 processor, 4Gb RAM with integrated ATI Radeon 3200HD grahics & an ALC888 codec integrated soundcard. It has HDMI out as well. I've tried a few distro's and have been around linux for a short time. I reckon I've settled on Ubuntu 12.04 (32bit) due to it doing pretty much everything I want it to. I'm working with a fresh install right now. I recently re-installed when I was going in circles trying to solve my problem before. I install Ubuntu and it works, except for the sound. I have tried things like reinstalling Alsa, editing my asound.conf file, installing HDA Verb and a few other things. Its at the point where I need to ask for help... Some outputs: ross@ross:~$ aplay -l ** List of PLAYBACK Hardware Devices ** card 0: SB [HDA ATI SB], device 0: ALC888 Analog [ALC888 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 ross@ross:~$ uname -r 3.2.0-34-generic-pae ross@ross:~$ lspci | grep VGA 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] ross@ross:~$ lspci | grep Audio 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) 01:05.1 Audio device: Advanced Micro Devices [AMD] nee ATI RS780 HDMI Audio [Radeon HD 3000-3300 Series] Added options snd-hda-intel position_fix=1 to alsa-base.conf file Unmuted all in alsamixer Can anyone suggest anything more?

  Read the article

• Packard Bell EasyNote MZ35 freezes when AC unplugged and wireless on

  - by Sense Hofstede

  I would like to ask for some help debugging an irritating problem I'm having with my Packard Bell EasyNote MZ35 and Ubuntu 10.10. Always when the laptop is connected to a wireless network and the AC power lead is unplugged—so it's running on battery power—the system freezes. The screen turns black and shows the error GLib-WARNING **: getpwuid_r(): failed due to unknown user id (0), although this error is completely unrelated to the actual problem. Previous searches on the internet indicate that this error is unrelated to the bug I'm experiencing. It is suggested that Ubuntu tries to hibernate or suspend and that you're seeing the black screen running 'behind' the X server. That would explain the fact that curiously you still see—but cannot move—the mouse cursor. I've already set all the values of the GConf keys in /apps/gnome-power-manager/actions/ to 'nothing', disabled all power management actions I could find, but it didn't solve the problem. It is important to note that the freeze doesn't happen immediately after you unplug the AC power lead. The icon in the notification area may have changed already, but the freeze only occurs when the Notify OSD bubble appears that tells you how many time is left with your battery. Does anyone here have a clue about this problem? A workaround or the cause? If anyone could help me with disabling possible suspend/hibernate behaviour that might be related to this issue, that would be appreciated too. This issue has been reported as bug #666852.

  Read the article

• Differentiating between Hard and Soft Dependencies - Fedora Yum [closed]

  - by Sujit

  I will ask this with an example - I have installed gnash-plugin on fedora 64 bit with Yum. It pulled in following packages - Installing : agg-2.5-9.fc13.x86_64 1/6 Installing : gtkglext-libs-1.2.0-10.fc12.x86_64 2/6 Installing : boost-thread-1.44.0-7.fc14.x86_64 3/6 Installing : boost-date-time-1.44.0-7.fc14.x86_64 4/6 Installing : 1:gnash-0.8.8-4.fc14.x86_64 5/6 Installing : 1:gnash-plugin-0.8.8-4.fc14.x86_64 6/6 Now, I tested the plugin and I didn't like it. I want to remove all these above packages which got installed with the plugin as I don't longer going to need them. How can I do this? I checked remove-with-plugin for yum but it pulls in all the packages which are currently depending on the packages. I understand the thought process behind showing what packages are getting affected - but I am wondering if there is any way of looking at the history with what package got installed when I installed a certain package. When gnash-plugin wasn't there firefox was running fine with but after I installation firefox is now depends on this new plugin. Has any one worked on differentiating hard-dependencies(hard means the program will break if that package is not there) and soft-dependencies ( soft means the program may not get affected fatally) ?

  Read the article

• Install Lubuntu w/o Disc or Flash Drive?

  - by Seib

  My WinXP desktop was recently blasted with a few bits of malware. I removed the malware but the damage is done, and my OS is finally at its end; it's barely chugging along as it is. So, I'm figuring what I'd like to do is replace the OS with Lubuntu, which I know is a lightweight, heavily WinXP-esque distro of Linux. However, every article, every explanation, I've read online has stated I need either a 4+ GiB flash drive or a burnable CD. Well, I have a flash drive, but it's only 1 GiB; and I have a disc burner, but no disc. So, frankly, I doubt I'll be able to do it. But hey, I figured I might as well ask away here on AU; what have I got to lose? So my question is this: would it be possible to replace my WinXP OS w/ Lubuntu without using either a 4+ GiB flash drive or a burnable CD? Thanks very much. I appreciate any help you could give.

  Read the article

• Unavailable packages repository

  - by bitmask

  I'm running ubuntu 11.10 (oneiric) on this machine, and suddenly, apt is unable to update properly. If I ask it to update its package information, by running apt-get update (or alternatively telling the update manager to "check"), it succeeds for about 120 packages (more precisely, I get about 120 Ign/Hit notes) and then says it cannot find universe Sources and restricted amd64: Hit http://de.archive.ubuntu.com oneiric-backports/multiverse Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/restricted Translation-en Hit http://de.archive.ubuntu.com oneiric-backports/universe Translation-en Err http://de.archive.ubuntu.com oneiric/universe Sources 404 Not Found [IP: 141.30.13.20 80] Err http://de.archive.ubuntu.com oneiric/restricted amd64 Packages 404 Not Found [IP: 141.30.13.20 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric/universe/source/Sources 404 Not Found [IP: 141.30.13.20 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/oneiric/restricted/binary-amd64/Packages 404 Not Found [IP: 141.30.13.20 80] E: Some index files failed to download. They have been ignored, or old ones used instead. I manually checked the de server and cannot find anything wrong with the stuff it's complaining about. Also it looks pretty much like, say, the us mirror. But oddly enough, the IP it lists, seems to point to a debian package server, which obviously does not contain ubuntu packages. So, is this a local problem that I can fix somehow (and if so, how?) or is there actually some server down right now?

  Read the article

• What is the correct way to restart udev in Ubuntu?

  - by zerkms

  I've changed the name of my eth1 interface to eth0. How to ask udev now to re-read the config? service udev restart and udevadm control --reload-rules don't help. So is there any valid way except of rebooting? (yes, reboot helps with this issue) UPD: yes, I know I should prepend the commands with sudo, but either one I posted above changes nothing in ifconfig -a output: I still see eth1, not eth0. UPD 2: I just changed the NAME property of udev-rule line. Don't know any reason for this to be ineffective. There is no any error in executing of both commands I've posted above, but they just don't change actual interface name in ifconfig -a output. If I perform reboot - then interface name changes as expected. UPD 3: let I explain all the case better ;-) For development purposes I write some script that clones virtual machines (VirtualBox-driven) and pre-sets them up in some way. So I perform a command to clone VM, start it and as long as network interface MAC is changed - udev adds the second rule to network persistent rules. Right after machine is booted for the first time there are 2 rules: eth0, which does not exist, as long as it existed in the original VM image MAC eth1, which exists, but all the configuration in all files refers to eth0, so it is not that good for me So I with sed delete the line with eth0 (it is obsolete and useless in cloned image) and replace eth1 with eth0. So currently I have valid persistent rule, but there is still eth1 in /dev. The issue: I don't want to reboot the machine (it will take another time, which is not good thing on building-VM-stage) and just want to have my /dev rebuilt with some command so I have ready-to-use VM without any reboots.

  Read the article

• Have to run sudo dhclient eth0 automatically every boot

  - by Fyksen

  I just installed ubuntu 12.04.1 alternative install (for raid 0 on some disks). I Have some problems with the net. I'm at school, we use cable, and it got IPv6. If I run ifconfig eth0 heres my output: eth0 Link encap:Ethernet HWaddr e0:cb:4e:87:ff:db inet addr:128.39.194.217 Bcast:128.39.194.223 Mask:255.255.255.224 inet6 addr: 2001:700:1100:8008:e2cb:4eff:fe87:ffdb/64 Scope:Global inet6 addr: fe80::e2cb:4eff:fe87:ffdb/64 Scope:Link inet6 addr: 2001:700:1100:8008:48f7:c23:1d87:da6c/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1063378 errors:0 dropped:0 overruns:0 frame:0 TX packets:489811 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1577173461 (1.5 GB) TX bytes:37043669 (37.0 MB) Interrupt:68 Base address:0x6000 My /etc/network/interfaces look like this: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 # NetworkManager#iface eth0 inet dhcp # NetworkManager#hostname 2001:700:1100:1::4 # This is an autoconfigured IPv6 interface iface eth0 inet6 auto (I had to remove the hash tags, because of the BIGFONT i get on ask ubuntu) The "network manager" says that I'm not connected. Let me know if you need any more information. :)

  Read the article

• Mounting an encrypted partion Error

  - by indiajoe

  Using the disk utilities in ubuntu 11.04, i had encrypted a partition with a passphrase. Each time i used to click on the partition to mount, it used to ask me the passphrase and get mounted. All was fine, until i installed the 12.04. After the installation, this encrypted partition, disappeared from the menu. fdisk -l /dev/sda Shows the encrypted partition in the list /dev/sda7 298953648 488392064 94719208+ 7 HPFS/NTFS/exFAT I tried the following commands to mount it. But they all gave following errors $ sudo cryptsetup luksDump /dev/sda7 Device /dev/sda7 is not a valid LUKS device. $ ecryptfs-unwrap-passphrase /dev/sda7 Passphrase: # i entered the correct passphrase here... Error: Unwrapping passphrase failed [-5] Info: Check the system log for more information from libecryptfs $ grep ecryptfs /var/log/syslog Oct 31 22:43:51 benny ecryptfs-unwrap-passphrase: Error attempting to open [/dev/sda7] for reading Nov 1 01:28:02 benny ecryptfs-unwrap-passphrase: Error attempting to open [/dev/sda7] for reading Nov 1 01:29:06 benny ecryptfs-unwrap-passphrase: Error attempting to open [/dev/sda7] for reading I don't understand why I am getting the "Device /dev/sda7 is not a valid LUKS device." Could it be due to some corruption in partition table? Is there any way to recover this encrypted partition? Thanks indiajoe

  Read the article

< Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >