Search Results

Search found 12681 results on 508 pages for 'logical drive'.

Page 46/508 | < Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >

  • Boot problems w/ External HDD

    - by JeremyT
    I'm having a problem with booting a live image off of a USB Hard Drive. I used Startup Disk Creator to make an Ubuntu 11.10 live image on a partition on my external so that I can use it on various computers. I set it up with ~4GB of persistent data So far I've tried it on two computers. One, a Dell, will boot to my external but it loads the select boot device very slowly. It hangs on a screen with an underscore for up to 5 minutes until it allows me to select which drive I want to boot from. After that, it works great. However, on my primary computer it doesn't work at all. It's an Acer from 2009 and it won't even recognize the drive. I don't see it anywhere in BIOS or the select boot disk list. The light on the external will come on at boot just fine so I know it's powering it at this time. Both computers worked perfectly with my 4GB flash drive that I had partitioned half and half (1st half FAT32 and second Ubuntu 11.10 live)

    Read the article

  • linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

    - by devicerandom
    We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

    Read the article

  • Mapped networkdrive on logout

    - by Robuust
    I'm using a script to keep a mapped networkconnection alive, but ofcourse the mapped connection is gone when I logout. The point is now, that I'm running this on Windows Server 2008 R2, where I use remote desktop to login on the administrator account. However, it should remain logged in and not remove the mapped connection as this script takes care of not logging out on MS office 365 sharepoint. Is there a way to keep the mapped networklocation (L:) available after logout? So the script can run to remain the connection? # Create an IE Object and navigate to my SharePoint Site $ie = New-Object -ComObject InternetExplorer.Application $ie.navigate('https://xxx.sharepoint.com/') # Don't need the object anymore, so let's close it to free up some memory $ie.Quit() # Just in case there was a problem with the web client service # I am going to stop and start it, you could potentially remove this # part if you want. I like it just because it takes out a step of # troubleshooting if I'm having problems. Stop-Service WebClient Start-Service WebClient # We are going to set the $Drive variable here, this is just # going to tell the command what drive letter to map you can # change this to whatever you want (if you change it to a # drive that is already mapped it will overwrite it, so be careful. $Drive = "L:" # You can change the drive destiniation to whatever you want, # it has to be a document library or folder of course. $DrvDest = "https://xxx.sharepoint.com/files/" # Here is where we create the object to map the network drive and # then map the network drive $net = New-Object -ComObject WScript.Network; $net.mapnetworkdrive($Drive,$DrvDest) # That is the end of the script, now schedule this with task # scheduler and every so often and you should be set.

    Read the article

  • How can I control disk numbering (enumeration) in Windows 7 Disk Management?

    - by tim11g
    A desktop system had two drives (Assigned C and D, which were enumerated in Disk Management as Disk 0 and Disk 1). A new SSD was added as the boot drive, after copying the C drive to the SSD. The SSD was connected to SATA 0 (master) port on the motherboard. The previous C Drive was moved to SATA 2 and is reformatted as a non-booting NTFS partition. The D drive remained on SATA 1. The system boots and everything seems fine. I was able to manually adjust the Drive Letters. However, the list in Disk Management is re-ordered. Disk 0 is the the previous Disk 2 (D Drive) on SATA 1, Disk 1 is the new Boot Drive (now C) on SATA 0, and Disk 2 is the former C Drive (now assigned E) on SATA 2. Does the Disk 0, 1, 2, designation mean anything? I would prefer to have them display in Disk Management as Drives C, D, and E from top to bottom. Is the Disk enumeration based on the SATA port or something else? (If it was based on SATA Port, they should be ordered C, D, E. Is there any way to re-order the Disk number assignments? What actually does determine the Disk number enumeration?

    Read the article

  • Recover data from physically damaged harddrive. What are my options?

    - by Michael Kniskern
    I was trying to replace the power supply in my desktop PC and ended up physically damaging the data connection from the hard drive to the motherboard. The plastic shelf for the copper prongs on the hard drive broke into the cable. Here is a picture of my handy work: I went to Best Buy Geek Squad to discuss my options and they said that they will need to send it to the recover center it could cost anywhere between $250 to $1600 USD to recover the data out the hard drive Is this reasonable for data recovery from a physically damaged hard drive? Are there any other options I can explore? I am going to talk to the data doctors to see what my options are. Update I took the HD to Data Doctors, and they told me that the SATA connection was broken to they would need to replaced the data connector and then copy the data to a brand new hard drive. So, with the initial analysis, cost of replacement parts, and data recovery fee it came out to $865.00 USD. The technician specifically stated if this was an older hard drive that would just need to replace the data connector. But because there is specific information related to the individual hard drive in the flash ROM, they need to transfer the data to a brand new hard drive.

    Read the article

  • Migrate Windows Server 2008 to a new hard disk

    - by MainMa
    Hi, I have a machine with Windows Server 2008. I want to change the hard disk drive, but keep everything else. I don't have a cd/dvd drive and don't want to buy it. My first idea was to make a byte-to-byte copy of the disk with Paragon Advanced Recovery. The problem is that when I try to boot from a new hard disk, it says that there were hardware changes and that Windows must be repaired, inviting me to insert the installation disk and follow repair instructions. I searched and found that 1:1 copy is not a correct way to do things. The correct one is to restore Windows to a new hard disk from a full system backup. But to restore, I need to have a dvd drive. I tried to make a copy of the Windows Server 2008 .iso on an USB flash drive, but the drive is not bootable (while the same procedure applied to Paragon Advanced Recovery ISO produces a bootable recovery USB flash drive). Now what else can I do (except buying a dvd drive)? Is there a way either to make Windows work without doing recovery or recover Windows 2008 without using a cd drive?

    Read the article

  • RAID controller dropping the wrong drive

    - by bramp
    I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

    Read the article

  • How is the extra mSATA SSD disk used/configured in a Dell XPS laptop?

    - by Mark
    Some machines in the new XPS laptop range from Dell come with a regular, large (500GB+) HDD and an additional 32GB m-SATA SSD. The only detail I can find about this extra drive on the Dell site is this: Store your important files, multimedia and photos with XPS 15’s large hard drive options. To get instant access to your media, choose an optional mSATA solid-state drive (SSD) that can boot up to twice as fast as a regular hard drive and resumes in less than 1 second. I'd like to know more about how this extra drive is set up and used, specifically: Is anything installed on it (e.g. OS files or a boot loader) or is it just used as swap space? Is the m-SATA drive visible as a lettered drive in Windows? (I'd guess not if it's used for swap file only.) Is this unusual configuration likely to cause any problems later down the line - e.g. when upgrading to Windows 8? As usual, Dell's sales team haven't been able to help. If anyone's actually got a Dell machine with this or a similar hard drive set-up and can give a definitive answer rather than speculation I'll accept the answer.

    Read the article

  • Data Modeling: Logical Modeling Exercise

    - by swisscheese
    In trying to learn the art of data storage I have been trying to take in as much solid information as possible. PerformanceDBA posted some really helpful tutorials/examples in the following posts among others: is my data normalized? and Relational table naming convention. I already asked a subset question of this model here. So to make sure I understood the concepts he presented and I have seen elsewhere I wanted to take things a step or two further and see if I am grasping the concepts. Hence the purpose of this post, which hopefully others can also learn from. Everything I present is conceptual to me and for learning rather than applying it in some production system. It would be cool to get some input from PerformanceDBA also since I used his models to get started, but I appreciate all input given from anyone. As I am new to databases and especially modeling I will be the first to admit that I may not always ask the right questions, explain my thoughts clearly, or use the right verbage due to lack of expertise on the subject. So please keep that in mind and feel free to steer me in the right direction if I head off track. If there is enough interest in this I would like to take this from the logical to physical phases to show the evolution of the process and share it here on Stack. I will keep this thread for the Logical Diagram though and start new one for the additional steps. For my understanding I will be building a MySQL DB in the end to run some tests and see if what I came up with actually works. Here is the list of things that I want to capture in this conceptual model. Edit for V1.2 The purpose of this is to list Bands, their members, and the Events that they will be appearing at, as well as offer music and other merchandise for sale Members will be able to match up with friends Members can write reviews on the Bands, their music, and their events. There can only be one review per member on a given item, although they can edit their reviews and history will be maintained. BandMembers will have the chance to write a single Comment on Reviews about the Band they are associated with. Collectively as a Band only one Comment is allowed per Review. Members can then rate all Reviews and Comments but only once per given instance Members can select their favorite Bands, music, Merchandise, and Events Bands, Songs, and Events will be categorized into the type of Genre that they are and then further subcategorized into a SubGenre if necessary. It is ok for a Band or Event to fall into more then one Genre/SubGenre combination. Event date, time, and location will be posted for a given band and members can show that they will be attending the Event. An Event can be comprised of more than one Band, and multiple Events can take place at a single location on the same day Every party will be tied to at least one address and address history shall be maintained. Each party could also be tied to more then one address at a time (i.e. billing, shipping, physical) There will be stored profiles for Bands, BandMembers, and general members. So there it is, maybe a bit involved but could be a great learning tool for many hopefully as the process evolves and input is given by the community. Any input? EDIT v1.1 In response to PerformanceDBA U.3) That means no merchandise other than Band merchandise in the database. Correct ? That was my original thought but you got me thinking. Maybe the site would want to sell its own merchandise or even other merchandise from the bands. Not sure a mod to make for that. Would it require an entire rework of the Catalog section or just the identifying relationship that exists with the Band? Attempted a mod to sell both complete albums or song. Either way they would both be in electronic format only available for download. That is why I listed an Album as being comprised of Songs rather then 2 separate entities. U.5) I understand what you bring up about the circular relation with Favorite. I would like to get to this “It is either one Entity with some form of differentiation (FavoriteType) which identifies its treatment” but how to is not clear to me. What am I missing here? u.6) “Business Rules This is probably the only area you are weak in.” Thanks for the honest response. I will readdress these but I hope to clear up some confusion in my head first with the responses I have posted back to you. Q.1) Yes I would like to have Accepted, Rejected, and Blocked. I am not sure what you are referring to as to how this would change the logical model? Q.2) A person does not have to be a User. They can exist only as a BandMember. Is that what you are asking? Minor Issue Zero, One, or More…Oops I admit I forgot to give this attention when building the model. I am submitting this version as is and will address in a future version. I need to read up more on Constraint Checking to make sure I am understanding things. M.4) Depends if you envision OrderPurchase in the future. Can you expand as to what you mean here? EDIT V1.2 In response to PerformanceDBA input... Lessons learned. I was mixing the concept of Identifying / Non-Identifying and Cardinality (i.e. Genre / SubGenre), and doing so inconsistently to make things worse. Associative Tables are not required in Logical Diagrams as their many-to-many relationships can be depicted and then expanded in the Physical Model. I was overlooking the Cardinality in a lot of the relationships The importance of reading through relationships using effective Verb Phrases to reassure I am modeling what I want to accomplish. U.2) In the concept of this model it is only required to track a Venue as a location for an Event. No further data needs to be collected. With that being said Events will take place on a given EventDate and will be hosted at a Venue. Venues will host multiple events and possibly multiple events on a given date. In my new model my thinking was that EventDate is already tied to Event . Therefore, Venue will not need a relationship with EventDate. The 5th and 6th bullets you have listed under U.2) leave me questioning my thinking though. Am I missing something here? U.3) Is it time to move the link between Item and Band up to Item and Party instead? With the current design I don't see a possibility to sell merchandise not tied to the band as you have brought up. U.5) I left as per your input rather than making it a discrete Supertype/Subtype Relationship as I don’t see a benefit of having that type of roll up. Additional Revisions AR.1) After going through the exercise for FavoriteItem, I feel that Item to Review requires a many-to-many relationship so that is indicated. Necessary? Ok here we go for v1.3 I took a few days on this version, going back and forth with my design. Once the logical process is complete, as I want to see if I am on the right track, I will go through in depth what I had learned and the troubles I faced as a beginner going through this process. The big point for this version was it took throwing in some Keys to help see what I was missing in the past. Going through the process of doing a matrix proved to be of great help also. Regardless of anything, if it wasn't for the input given by PerformanceDBA I would still be a lost soul wondering in the dark. Who knows my current design might reaffirm that I still am, but I have learned a lot so I am know I at least have a flashlight in my hand. At this point in time I admit that I am still confused about identifying and non-identifying relationships. In my model I had to use non-identifying relationships with non nulls just to join the relationships I wanted to model. In reading a lot on the subject there seems to be a lot of disagreement and indecisiveness on the subject so I did what I thought represented the right things in my model. When to force (identifying) and when to be free (non-identifying)? Anyone have inputs? EDIT V1.4 Ok took the V1.3 inputs and cleaned things up for this V1.4 Currently working on a V1.5 to include attributes.

    Read the article

  • Can you use a USB hard drive in ESXI?

    - by semi
    I know that you can install ESXi 4.0 on a thumbdrive, but I was wondering if you could plug in an external harddrive to give extra storage to one of your VMs? We run a fileserver inside of ESXi that needs a space upgrade, but we're thinking of migrating to a different fileserver solution and would rather stick to external media to ease the later transition. edit: Ideally I'd like the drive to show up to the VM directly and not have ESXi control it, so that I could move it to a different machine and still have all of the data appear the same.

    Read the article

  • Can I rebuild degraded RAID1 on a SAS 5 i controller with a larger mirror drive size?

    - by Kenny
    A drive failed on a Dell SAS 5i controller - see controller bios screengrab: http://imagebin.ca/view/SkZbszA.html The primary is a 160GB 10k sata drive. I added a 250GB 7k rpm drive in the hope that the array would rebuild onto this drive. This did not happen. (assuming that the controller would just operate at the speed of the slowest drive) The controller could see the new drive, but it didn't automatically rebuild the raid1 onto this drive. (my assumption is that it did not do this rebuild as the drive sizes are different). There was an option to add the new drive to the existing raid1 array - but when I tried this a message appeared stating that all data on the array would be lost. (I didn't get a screenshot of this message, I will later) Should the SAS 5i allow me to rebuild the array onto a larger drive? Is the option to add the drive to the array the right way to go? Many thanks!

    Read the article

  • Windows XP-64 loses audio sounds, drive letters... why?

    - by Ira Baxter
    Until sometime in early December, I had a wonderfully functioning XP-64 system. It was configured to auto download/install MS patches. I occassionally update the software on it, e.g. Open Office, Adobe Reader, Skype, but I don't fetch hundreds of tools or anything much beyond what I just mentioned. In December, suddenly my audio stopped, and drive letters assigned to various mount points on other machines quit being available. Apparantly, the services that support these (and some others) are now not starting up when I boot/login. There isn't anything obvious in the event log. If I manually restart the associated services, these facilities come back on line and work for awhile (a day) but pretty soon the problem reappears. I don't reboot very often, nor do I log out out much. Hints?

    Read the article

  • Setting up a laptop hard drive as a secondary on a tower?

    - by vermiculus
    I'm trying to install Windows 8 for a friend who has recently bricked a laptop hard drive. The new one is OEM so there is no OS - I need to be able to stick it in to my tower and load the new OS on it. Both bricked and replacement laptop hard drives are SATA and connect to my mobo just like any other. After I post this I'm going to check the BIOS and see if it shows up, but so far I don't have it showing up in Disk Management. Any ideas would be greatly appreciated.

    Read the article

  • How to prevent hard drive from spinning down Windows 7?

    - by JL.
    I had a Western Digital External 1TB drive, which I was accessing via USB. I decided one day, that I would prefer to mount the HDD in my case, and access it via SATA interface. So I took it apart, and the actual mounting was a breeze. The only thing is, I think the device has some default power saving features, which means the device tends to stop spinning when idle for (x) amount of time. This creates delays when I am accessing the HDD. Is there anyway I can turn off these power saving features for this HDD?

    Read the article

  • What are logical and path queries

    - by NomeN
    I'm reading a paper which mentions that a language for refactoring has three specific requirements. functional features (like ML) logical queries (like Datalog) path queries (like Datalog) I know what they mean by functional features, but I'm not totally clear on the latter two and can't find a clear explanation either. Although I have a good idea after what I could find on the subjects, I need to be sure so here goes: Could the SO-community please clearly explain to me what logical queries and path queries are? Or at the very least what the people from the paper meant?

    Read the article

  • How to boot from a flash drive OS using VirtualBox?

    - by kokbira
    I have two flash drive, one with Slax installed and another for Android x86 Live installed, but they do not boot in my laptop (in my work they boot perfectly). I can boot from some live CDs/DVDs or its ISO files using VirtualBox, but I cannot do it for live flash drives - I put the flash drives and start a VirtualBox without any virtual HD, but VirtualBox does not recognize them as boot options, as it does for CDs/DVDs. Any ideas? Any alternatives if VirtualBox does not support it? Edit1: I'm using Windows (Windows 7) but I would like to know how to do it in Linux (Ubuntu, for example) too.

    Read the article

  • HP Probook 4530s great specs, but lagging. Hard Drive?

    - by Mark
    I have this laptop, which has a i3 processor, 4gb memory, 7200rpm hard drive. So there is nothing wrong with the specs. Even when I have no applications open, simply closing and opening windows, lags. Or opening the start menu, or dragging icons across the desktop. sometimes even the cursor lags. So I checked out the resource monitor, and the resources using disk activity are svchost Avast ------- my antivirus, but not much System (PID 4) ------ This is using a huge chunk The total disk activity fluctuates between %50 - %100

    Read the article

  • Can I rebuild degraded RAID1 on a SAS 5 i controller with a larger mirror drive size?

    - by Kenny
    Hi, A drive failed on a Dell SAS 5i controller - see controller bios screengrab: http://imagebin.ca/view/SkZbszA.html The primary is a 160GB 10k sata drive. I added a 250GB 7k rpm drive in the hope that the array would rebuild onto this drive. This did not happen. (assuming that the controller would just operate at the speed of the slowest drive) The controller could see the new drive, but it didn't automatically rebuild the raid1 onto this drive. (my assumption is that it did not do this rebuild as the drive sizes are different). There was an option to add the new drive to the existing raid1 array - but when I tried this a message appeared stating that all data on the array would be lost. (I didn't get a screenshot of this message, I will later) Should the SAS 5i allow me to rebuild the array onto a larger drive? Is the option to add the drive to the array the right way to go? Many thanks!

    Read the article

  • Is there a command line (or autohotkey) way of dismounting a USB drive?

    - by justintime
    I find dismounting a USB drive takes far too many mouse clicks for my liking. Is there are command line way of doing it (XP and Vista)? Addition I have an eye condition that makes hand mouse coordination difficult so any suggestion that there aren't too many clicks will be downvoted as not answering my question. However I use AutoHotkey a lot and one use case would be to call it from an AHK script. So if there is a way to code it in AHK that will do. Added this to the tags. Further question - is it safe to remove a disk when the computer is a. on Standby or b. Hibernated. I recall that W2000 got uspet if you pulled a disk from a hibernated machine. Or is it better to explicitly dismount or sync before you hibernate or standby - prabably in a script.

    Read the article

  • Can I lose files when changing security on an XP drive within Windows 7?

    - by Will
    Hard to come up with a title for this one, sheesh. Have a friend whose computer went down. He asked me to get all his data off his drive. His old computer was running XP. So, I've plugged it into my Windows 7 computer. When I attempt to open up his Documents and Settings folder, I get prompted to elevate in order to "permanently get access to this folder." If I do this, will I be able to access the files in this directory, or will all the current files be lost? I may be overly paranoid about this, but I can't find any information about exactly what will happen when I do this. TIA.

    Read the article

  • Is it safe to run an operating system from an USB flash drive?

    - by Georg
    I've got a laptop that has a broken harddisk controller. Replacing the motherboard is quite expensive. I thought about buying a flash drive and installing & running the system from it. However, I'm concerned about some things. Speed: Are they fast enough for swap memory (I've got only 1GB RAM installed.) I'm considering buying 2 or 3 of them and making them into a RAID. What about limited write cycles? How long will it last for a system that has a filesystem with journaling enabled? I'd hate to abandon it. Are there significant differences between internal SSD which are used in modern laptops like MacBooks and USB flash drives? What should I expect in 10 years when the memory wear starts kicking in?

    Read the article

  • How to Create a shortcut to files / folders on a drive with different / changing letters (root)?

    - by Rolo
    I have seen this question asked and answered many times but the location one usually desires to create the shortcut is on the actual drive with the different letters. I would like to create the shortcut on the drive with the permanent letter. So, let me explain further. I have a C Drive and a G Drive. The C Drive is always C and it's on a Windows XP computer. The G drive may be G today, but H tomorrow. How can I create a permanently working shortcut on the C Drive that points to the G, sometimes H, external hard drive? P.S. I am referring to an external hard drive, but I would also (not instead) be interested in the answer if it were a usb flash drive. (Keep in mind the shortcut is being created on the drive with the permanent letter). Thanks.

    Read the article

  • C drive should only contain OS. Myth or fact?

    - by Fasih Khatib
    So, I have a 500GB HDD @7200RPM. It is split as: C: 97GB D: 179GB E: 188GB My belief is to keep OS ONLY in C:\ and any adamant programs that won't go anywhere apart from C:\ [because this speeds up the PC during startup process] and install programs in D:\ so that in case I have to reinstall the OS, I will have the programs readily available after reinstall. But I have begun to think this approach is flawed because if C:\ is formatted, I will lose registry values and stuff that goes in %appdata% and so it is no use keeping programs in D:/ drive because they will be useless after all. Should I go ahead and install ALL of my programs in C:\ and then use D:\ and E:\ for storing my data like photos, text files, java files n all? How will this impact the performance of the HDD? I only have 3 programs in D:\Program Files so it will be easy to reinstall them :)

    Read the article

  • My Portable Hard Drive with USB3 didn't work when connected to My Laptop, but it working with USB2 properly

    - by Mohammad Hasan Esfahanian
    I have Western Digital My Passport Essential Portable Hard Drive with USB3 and Model:WDBACY5000ABK-EESN. Until about two or three months ago when I connected that to My Laptop USB3 port, that worked very well. But now when I'm connecting that to My device, The system does not detect any Hard Drives. When plug in the USB2 port is working properly. I connected that to another Laptop whit USB3 port but I had the same problem. I tested My Laptop port with a Flash Memory by USB3 and ports were healthy and I'm sure they are working. For this issue, I changed the windows, but it still did not work. What can I do? Thanks in advance.

    Read the article

< Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >