Search Results

Search found 14780 results on 592 pages for 'low level'.

Page 460/592 | < Previous Page | 456 457 458 459 460 461 462 463 464 465 466 467  | Next Page >

  • Redirect specific domains with DNS

    - by user66377
    Currently we filter internet content using OpenDNS, our internal Windows DC/DNS servers point to the router's DNS, which then points to the OpenDNS servers. This works well to block all computer's on the network equally. New issue. We now need to separate what computers can go to what sites. So facebook is blocked for everyone right now, but I need to open it up to the 3 community computers now. The 3 community computers will be on an untrusted network seperate from the company computers so they can have their own DNS server, from their own router. The issue is though they still must connect to the internet using the same IP address. So OpenDNS sees the same IP and blocks them the same way. We are looking into getting a second IP, but it's not likely an option without going up to the next major level with our ISP which we don't want to do. My thought is this. Can I setup a DNS server on the untrusted network, and then depending on the request that comes in, have it send it to either OpenDNS or our ISP's DNS? Example www.facebook.com and www.youtube.com are both on the OpenDNS blacklist. So if they go to www.youtube.com, the local DNS server goes to the ISP's DNS to get the IP and thus the client gets the right IP and can go to the site. This would be manually entered for each allowed site thus creating a white list. Then if they go to www.facebook.com, since the local DNS server does not find an entry, it sends the request to OpenDNS, which then sees the site is on the blacklist, and thus sends the it's blocked webpage. The local DNS server can be either Bind on Linux or MS DNS on Window 2008. If this can be done, can you give some direction as well as I've never setup a DNS such as this before. Thanks

    Read the article

  • Recommendations for colocation in the US

    - by Emil
    Hello serverfault I work for a European media company and we are currently looking for colocation in the US. I know the European market quite well unfortunately that is not the case for the US. I'm hoping for you guys to help me out a bit with a few questions, it would be much appreciated! I am looking for a data center that can deliver a high level of availability (tier 3 or better). The installation will be fairly large so capacity is important. Good internet connectivity/carrier presence. However most important is good customer support, skilled dedicated and responsive technical staff, since we won't have tech staff close by. I'm looking for a small and fast moving company that target internet businesses rather than big old enterprise hosting. What locations should we go for given that we want to reach all of the US from a single site and still maintain decent latency? (do we need east and west coast?) Where are the main internet hubs and should you try and get as close as possible? Are there any good online resources I should look at? Where do the large scale internet/media services colocate? Lastly I would be very happy to get some actual recommendations for companies to talk to P.S I'm happy to return the favor if anyone has question regarding data centers and colocation in Europe.

    Read the article

  • setting up git on cygwin - openssl

    - by user23020
    I'm trying to get git running in cygwin on a windows 7 machine I have git unpacked and the directory git-1.7.1.1 when i run make install from within that directory, I get CC fast-import.o In file included from builtin.h:4, from fast-import.c:147: git-compat-util.h:136:19: iconv.h: No such file or directory git-compat-util.h:140:25: openssl/ssl.h: No such file or directory git-compat-util.h:141:25: openssl/err.h: No such file or directory In file included from builtin.h:6, from fast-import.c:147: cache.h:9:21: openssl/sha.h: No such file or directory In file included from fast-import.c:156: csum-file.h:10: error: parse error before "SHA_CTX" csum-file.h:10: warning: no semicolon at end of struct or union csum-file.h:15: error: 'crc32' redeclared as different kind of symbol /usr/include/zlib.h:1285: error: previous declaration of 'crc32' was here csum-file.h:15: error: 'crc32' redeclared as different kind of symbol /usr/include/zlib.h:1285: error: previous declaration of 'crc32' was here csum-file.h:17: error: parse error before '}' token fast-import.c: In function `store_object': fast-import.c:995: error: `SHA_CTX' undeclared (first use in this function) fast-import.c:995: error: (Each undeclared identifier is reported only once fast-import.c:995: error: for each function it appears in.) fast-import.c:995: error: parse error before "c" fast-import.c:1000: warning: implicit declaration of function `SHA1_Init' fast-import.c:1000: error: `c' undeclared (first use in this function) fast-import.c:1001: warning: implicit declaration of function `SHA1_Update' fast-import.c:1003: warning: implicit declaration of function `SHA1_Final' fast-import.c: At top level: fast-import.c:1118: error: parse error before "SHA_CTX" fast-import.c: In function `truncate_pack': fast-import.c:1120: error: `to' undeclared (first use in this function) fast-import.c:1126: error: dereferencing pointer to incomplete type fast-import.c:1127: error: dereferencing pointer to incomplete type fast-import.c:1128: error: dereferencing pointer to incomplete type fast-import.c:1128: error: `ctx' undeclared (first use in this function) fast-import.c: In function `stream_blob': fast-import.c:1140: error: `SHA_CTX' undeclared (first use in this function) fast-import.c:1140: error: parse error before "c" fast-import.c:1154: error: `pack_file_ctx' undeclared (first use in this functio n) fast-import.c:1154: error: dereferencing pointer to incomplete type fast-import.c:1160: error: `c' undeclared (first use in this function) make: *** [fast-import.o] Error 1 I'm guessing that most of these errors are due to the iconv.h and openssl files which apparently are missing, but I can't figure out how I'm supposed to install those (if I am), or if there is some other way to get around this.

    Read the article

  • After update to Windows 8.1 brigthness isn't working (changing)

    - by Bibo
    I just update my Windows 8 to Windows 8.1 by Windows Store and I have some problems. My notebook is Acer Aspire Timelinex 3820TG and I know it's little old for Windows 8 but I install them and works fine (I updated my HDD to SSD). Now I just updated Windows and I have problem with changing brightness on my dedicated graphic card (Ati HD 5650). First I can changing brigthness with fn + keys but It just changing level in OS. No change in real. I tried reinstall drivers, install drivers for my card from Acer with compatibility to Windows 7 and without change. When I switch to integrated card changing brightness works. I think the problem is with drivers but I don't know how to get it working. Thanks for help Bonus question: I have another problem (but this one is not so important). Does anyone knows what msietxghh.exe is doing? Everytime when my system runs (after update) I get message that this program stops working but I just cancel and looks everything works fine.

    Read the article

  • Application to automate Windows software installation in a test lab

    - by Marc
    I have several test environments (hyper-V) which contain a variety of windows servers. Each machine needs periodically rolling back to a given snapshot and then re-installing with the latest version of our software to test. The software installs are quite complex MSI's with a fair few option screens. I know that the installs can be driven from the command line, passing in parameters to override the wizard options. At the simplest level I suppose I could just write a batch file to kick off each install with the required parameters, however the values that are passed in do need to change from time to time (and environment to environment) so a tool with a config file and simple GUI seems like a better idea. I think what makes it slightly more painful is the multiple environments. For example one environment might contain 4 servers and need a config file with all the server names, service endpoints etc. Another environment might be a 1-box install with all names and endpoints set to localhost. So, ideally I want to be able to store different setup configurations and use them to run all the required installers with the relevant settings against the relevant machines. Before I go off to write the thing, does anyone know of an existing, simple, free tool that will let me achieve this?

    Read the article

  • Architecture for highly available MySQL with automatic failover in physically diverse locations

    - by Warner
    I have been researching high availability (HA) solutions for MySQL between data centers. For servers located in the same physical environment, I have preferred dual master with heartbeat (floating VIP) using an active passive approach. The heartbeat is over both a serial connection as well as an ethernet connection. Ultimately, my goal is to maintain this same level of availability but between data centers. I want to dynamically failover between both data centers without manual intervention and still maintain data integrity. There would be BGP on top. Web clusters in both locations, which would have the potential to route to the databases between both sides. If the Internet connection went down on site 1, clients would route through site 2, to the Web cluster, and then to the database in site 1 if the link between both sites is still up. With this scenario, due to the lack of physical link (serial) there is a more likely chance of split brain. If the WAN went down between both sites, the VIP would end up on both sites, where a variety of unpleasant scenarios could introduce desync. Another potential issue I see is difficulty scaling this infrastructure to a third data center in the future. The network layer is not a focus. The architecture is flexible at this stage. Again, my focus is a solution for maintaining data integrity as well as automatic failover with the MySQL databases. I would likely design the rest around this. Can you recommend a proven solution for MySQL HA between two physically diverse sites? Thank you for taking the time to read this. I look forward to reading your recommendations.

    Read the article

  • Samba PDC share slow with LDAP backend

    - by hmart
    The scenario I have a SUSE SLES 11.1 SP1 machine as Samba master PDC with LDAP backend. In one share there are Database files for a Client-Server application. I log XP and Windows 7 machines to the local domain (example.local), the login is a little slow but works. In the client computers have an executable which opens, reads and writes the database files from the server share. The Problem When running Samba with LDAP password backend the client application runs VERY SLOW with a maximum transfer rate of 2500 MBit per second. If disable LDAP the client app speed increases 20x, with transfer rate of 50Mbit/sec and running smoothly. I'm doing test with just two users and two machines, so concurrency, or LDAP size shouldn't be the problem here. The suspect LDAP, Smb.conf [global] section configuration. The Question What can I do? I've googled a lot, but still have no answer. Slow smb.conf WITH LDAP [global] workgroup = zmartsoft.local passdb backend = ldapsam:ldap://127.0.0.1 printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = Yes add machine script = /usr/sbin/useradd -c Machine -d /var/lib/nobody -s /bin/false %m$ domain logons = Yes domain master = Yes local master = Yes netbios name = server os level = 65 preferred master = Yes security = user wins support = Yes idmap backend = ldap:ldap://127.0.0.1 ldap admin dn = cn=Administrator,dc=zmartsoft,dc=local ldap group suffix = ou=Groups ldap idmap suffix = ou=Idmap ldap machine suffix = ou=Machines ldap passwd sync = Yes ldap ssl = Off ldap suffix = dc=zmartsoft,dc=local ldap user suffix = ou=Users

    Read the article

  • How do I make ESXi 5.0 to shutdown virtual machines when the physical power button is pushed?

    - by Pawel Sawicki
    I have a home NAS/DLNA server built out of an HP Micro Server with the HP branded VMware ESXi 5.0.0 build-623860 (free license) installed. Being a home media center I'd like it to be "manageable" by all my household members. This requires that it needs to be powered on an off (including all the VMs inside) by anybody with the physical access to the server by simply pressing the power button on the chassis. The "startup" part is easy to obtain - all I had to do was to configure the startup/shutdown policy: Once the server powers up, all VMs start as well and that's exactly what I need. Well.. it did work up until 5.0.0U1, but that's a different story: http://blogs.vmware.com/vsphere/2012/03/free-esxi-hypervisor-auto-start-breaks-with-50-update-1.html Unfortunately, pressing the power button doesn't gracefully shutdown the guest machines - they are terminated instead. If I run the "shut down" command from the vSphere Client interface guests are powered off. I'd like to get the same end result when the physical power button is switched. I've poked around a bit on the ESXi server. There's a "/sbin/shutdown.sh" script that seemed to do exactly what I need... but after trying it does exactly what the power off button. The "/etc/inittab" contains an entry for the "shutdown" level but I suppose it's not hooked to the power button. I can't find any acpi related configuration, neither do I know what exactly is executed when the power button is pressed. Does anybody have a clue how can I make the VMs shutdown automatically when the physical power switch is pressed to turn of the computer?

    Read the article

  • What's the lowest cost, legal, Microsoft server stack you can assemble?

    - by McKAMEY
    Assuming that you have an app infrastructure that generally only requires: ASP.NET MVC / C# / .NET Database or NoSQL data store (must be accessible from C#) Here's the challenge to you server gods: What is the least expensive configuration that will allow you to deploy to production in a way that doesn't break any licensing rules? In what ways does this solution differ from the "standard" Microsoft deployment scenario? Where does this solution's performance break down once the app begins to scale? I'm not concerned about the hardware, only the server software itself. I would love to hear about any solutions you've personally put into production. Especially if they are unique alternatives. For ideas, consider some of the possible variations, a) any Microsoft server solutions where they have lowered the barrier to entry to compete with OSS, or b) any OSS alternatives to Microsoft products which perform at a similar level. An example of a): SQL Server 2008 Express Edition SP1 is a 100% free version of SQL Server which will scale to the needs of many smaller / early stage applications. An example of b): running the Mono Framework on Linux. An example of differing from the "standard" stack: running Mono on Linux will require a completely different server OS familiarity. None of the Windows-based knowledge really transfers. An example of breaking down under scale: SQL Server Express will only scale to 1GB of memory and 4GB of disk storage. After that point, the application will need to move to one of the paid versions of SQL Server.

    Read the article

  • How to recover a Linksys WRT54GL router that has a blinking green power LED and no response from the

    - by Peter Mounce
    I was flashing the router with the Tomato firmware, but something went wrong; I'm not sure what. Now, the router responds to ping at 192.168.1.1 (my Mac's on a static IP 192.168.1.21), but the web-interface doesn't come up. I have read that this situation is recoverable in a [couple of places][2], but I haven't been having much success and so I wondered whether anyone could help. From my Mac (OSX 10.5) I have tried to tftp a new vanilla-Linksys firmware to the router and reboot; according to the trace, this sends it but the router behaves no differently after a reboot. I've read that if boot_wait is turned on, I'll have an easier time, but I haven't been able to find any instructions that tell me how I can tell whether I did this or not (I don't think I have, but I might have, when I tinkered the first time months ago - the router has worked since then, though). I have found a couple of references to [something called JTAG][3], which seems like some kind of [homebrew diagnostic cable thing][4], but that's a little beyond my ken. Happy to try it, with muppet-level instructions, though (I do software, not hardware!). So, I'm at a bit of a loss, really, and wondered whether anyone could provide me with the route (ha. ha.) out of this mess? Hm, I can't post all the links I wanted to until I have some more reputation.

    Read the article

  • Reasonable automatic HTML to PDF conversion (in UNIX/Linux environment)

    - by Alex Balashov
    Is there a way to generate PDF documents from HTML files automatically in Linux where the PDF offers some kind of reasonable level of resemblance to the input file? A command-line tool - as opposed to an interactive GUI of some kind - is key. I have tried htmldoc and some related cousins, of course. But these tools are hopelessly stone-age; htmldoc doesn't support CSS at all. You won't find a lot of HTML documents these days that don't have at least some CSS styling. I don't really care about stupid effects or minor embellishments, but the issue is that CSS is at the core of most layouts these days; not many folks are using 6 layers of nested tables anymore. So, if the conversion tool has no grasp of CSS whatsoever, it's not just a matter of "the document doesn't look quite right"; it is likely to not meet the minimum standard of usability at all. It has been suggested to me by some folks to try to use the Gecko rendering engine to generate images that can be converted to PDFs, but I have no idea how one would go about doing this, let alone easily. I have no trouble believing that there are good commercial tools that do this, but I'm really looking for an open-source package if possible, as the endeavour itself is an open-source one and doesn't pay. Thanks in advance!

    Read the article

  • JVM system time runs faster than HP UNIX OS system time

    - by winston
    Hello I have the following output from a simple debug jsp: Weblogic Startup Since: Friday, October 19, 2012, 08:36:12 AM Database Current Time: Wednesday, December 12, 2012, 11:43:44 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:45:38 AM Line 1 was a recorded variable during WebLogic webapp startup. Line 2 was output from database query select sysdate from dual; Line 3 was output from java code new Date() I have checked from shell date command that line 2 output conforms with OS time. The output of line 3 was mysterious. I don't know how it comes from Java VM. On another machine with same setting, the same jsp output like this: Weblogic Startup Since: Tuesday, December 11, 2012, 02:29:06 PM Database Current Time: Wednesday, December 12, 2012, 11:51:48 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:51:50 AM Another machine: Weblogic Startup Since: Monday, December 10, 2012, 05:00:34 PM Database Current Time: Wednesday, December 12, 2012, 11:52:03 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:52:07 AM Findings: the pattern shows that the longer Weblogic startup, the larger the discrepancy of OS time with JVM time. Anybody could help on HP JVM? On HP UNIX, NTP was done daily. Anyway here comes the server versions: HP-UX machinex B.11.31 U ia64 2426956366 unlimited-user license java version "1.6.0.04" Java(TM) SE Runtime Environment (build 1.6.0.04-jinteg_28_apr_2009_04_46-b00) Java HotSpot(TM) Server VM (build 11.3-b02-jre1.6.0.04-rc2, mixed mode) WebLogic Server Version: 10.3.2.0 Java properties java.runtime.name=Java(TM) SE Runtime Environment java.runtime.version=1.6.0.04-jinteg_28_apr_2009_04_46-b00 java.vendor=Hewlett-Packard Co. java.vendor.url=http\://www.hp.com/go/Java java.version=1.6.0.04 java.vm.name=Java HotSpot(TM) 64-Bit Server VM java.vm.info=mixed mode java.vm.specification.vendor=Sun Microsystems Inc. java.vm.vendor="Hewlett-Packard Company" sun.arch.data.model=64 sun.cpu.endian=big sun.cpu.isalist=ia64r0 sun.io.unicode.encoding=UnicodeBig sun.java.launcher=SUN_STANDARD sun.jnu.encoding=8859_1 sun.management.compiler=HotSpot 64-Bit Server Compiler sun.os.patch.level=unknown os.name=HP-UX os.version=B.11.31

    Read the article

  • Why is my global security group being filtered out of my logon token?

    - by Jay Michaud
    While investigating the effects of filtered tokens on my file permissions, I noticed that one of my global security groups is being filtered in addition to the regular system-defined filtered groups. My Active Directory environment is a single-domain forest on the Windows Server 2003 functional level. I'll call the domain "mydomain.example.com". I am logged onto a Windows Server 2008 Enterprise Edition machine (not a domain controller) as a member of the "MYDOMAIN\Domain Admins" group and the "MYDOMAIN\MySecurityGroup" global security group (among others). When I run "whoami /groups" from an elevated command prompt, I see the full list of groups to which my account belongs as expected. When I run "whoami /groups" from a regular, non-elevated command prompt, I see the same list of groups, but the following groups are described as "Group used for deny only". BUILTIN\Administrators MYDOMAIN\Schema Admins MYDOMAIN\Offer Remote Assistance Helpers MYDOMAIN\MySecurityGroup Numbers 1 through 3 above are expected based on Microsoft documentation; number 4 is not. The "MYDOMAIN\MySecurityGroup" global security group is a group that I created. It contains three non-built-in global security groups, and these security groups contain only non-built-in user accounts. (That is, I created all of the accounts and groups that are members of the "MYDOMAIN\MySecurityGroup" global security group.) There are other, similar groups of which my account is a member that are not being filtered out of my logon token, and this group is not granted any specific user rights in the security settings of this computer or in Group Policy. What would cause this one group to be filtered out of my logon token?

    Read the article

  • How do i set up a fully featured small business network?

    - by JoshReedSchramm
    This has the possibility to be a very large question but I recently acquired a few rack mount servers and the hardware necessary to run them. Unfortunately I'm a programmer with very little understanding of how to set up a good working network so I'm hoping someone on here might be able to help. What I want to do is run a domain with a series of subdomains which would all be externally accessible. The setup would live inside my home and my internet connection is your run of the mill cable model (which means a dynamic IP) I want to be able to set up a couple site, specifically: www.mycompany.com (mycompany.com with no subdomain would redirect to this) build.mycompany.com (for my continuous integration server) ruby.mycompany.com (for ruby projects) win.mycompany.com (for windows project) etc. Additionally this is still my home network so our personal machines need to be able to get on via wifi with at least the same security we have now through an out of the box router from best buy. I'm thinking i need a DNS server, DHCP server and one of those would run either no-ip or dyndns to accommodate the dynamic ip. I don't necessarily need mail but it might be helpful to have some sort of mail server i could use for testing, it doesn't need to get out to the greater internet though. So how do i set up this kinda of network? tl;dr Need to know how to set up your standard office style network in my home off my normal consumer level cable modem connection.

    Read the article

  • Is there a free XML viewer to do "pivot tables"

    - by FumbleFingers
    I have an *.xml file on a PC running Windows XP, with a structure something like... <movies id="my movies" <movie name="Unforgiven" <people star="Clint Eastwood" director="Clint Eastwood"/> </movie> <movie name="A Fistful of Dollars" <people star="Clint Eastwood" director="Sergio Leone"/> </movie> <movie name="J Edgar" <people star="Leonardo DiCaprio" director="Clint Eastwood"/> </movie> </movies> I want to open this file in a viewer utility which will show one line per movie, filtered by a condition such as director="Clint Eastwood", including the relevant value for movie name on each line. Note - that's just an example. My actual file has thousands of lines, each possibly several hundred bytes long, and there are many more levels and named values. The important thing is I want to apply a filter for a specified value of some field at some level. And I want to see one line for every case where that value occurs, showing the values for any fields I specify, even if they're stored at higher levels. I may be mistaken in saying what I want is a "pivot table" - I don't know what I should call it.

    Read the article

  • Does visual source safe take .cvsignore as configuration ?

    - by superuser
    An easy way to tell CVS to ignore these directories is to create a file named .cvsignore (note the leading period) in your top-level source directory Has anyone verified this with vss? Plus,does vss have these similar command lines: * To refresh the state of your source code to that stored in the the source repository, go to your project source directory, and execute cvs update -dP. * When you create a new subdirectory in the source code hierarchy, register it in CVS with a command like cvs add {subdirname}. * When you first create a new source code file, navigate to the directory that contains it, and register the new file with a command like cvs add {filename}. * If you no longer need a particular source code file, navigate to the containing directory and remove the file. Then, deregister it in CVS with a command like cvs remove {filename}. * While you are creating, modifying, and deleting source files, changes are not yet reflected in the server repository. To save your changes in their current state, go to the project source directory and execute cvs commit. You will be asked to write a brief description of the changes you have just completed, which will be stored with the new version of any updated source file.

    Read the article

  • Somewhat powerful server needed for computationally expensive stuff

    - by Dane Larsen
    So here's my problem. My Dad runs a company that does some rather computationally expensive stuff. This is not supercomputer level stuff, but it does take several hours to run the average job on his Core i7 desktop. He asked me to look into a way to have his customers use the code on an hourly basis, namely via a server. Ideally he'd be able to buy a box for about $1000, and hook it right up to our home connection. Unfortunately, the data that needs to be both sent and received is on the order of several hundred megs. We live in a rural area, and the fastest connection offered is 1.5Mbit/s. Download. It's like .3Mbit/s upload. Not workable. What are the options for this kind of thing? Ideally, we'd have about 2GB of ram, 300-500GB of storage, and a nice dual core, and it has to run some flavor of Linux. Any suggestions? Thanks in advance EDIT: Also, ideally the monthly price would be < $100 per month.

    Read the article

  • Cannot login to ISCSI Target - hangs after sending login details

    - by Frank
    I have an ISCSI target volume, to which i am trying to connect using CentOS Linux server. Everything works fine, but cannot its stuck at login. Here are the steps i am performing: [root@neon ~]# iscsiadm -m node -l iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session20 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session21 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session22 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session23 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session30 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session31 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session78 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session79 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session80 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session81 Logging in to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) After this step, its stucks, waits for some time and then gives this output: Logging in to [iface: iface1, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) iscsiadm: Could not login to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260]. My iscsi.conf is this: node.startup = automatic node.session.timeo.replacement_timeout = 15 # default 120; RedHat recommended node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 5 node.session.err_timeo.abort_timeout = 15 node.session.err_timeo.lu_reset_timeout = 20 node.session.initial_login_retry_max = 8 # default 8; Dell recommended node.session.cmds_max = 1024 # default 128; Equallogic recommended node.session.queue_depth = 32 # default 32; Equallogic recommended node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 discovery.sendtargets.iscsi.MaxRecvDataSegmentLength = 32768 node.conn[0].iscsi.HeaderDigest = None node.session.iscsi.FastAbort = Yes Also, in access control, i have given full access to Any IP, Any CHAP user and fixed iscsi initiator name. With same access level, all other volumes on rest of servers are working, except this one.

    Read the article

  • Filezilla client unable to get directory listing from Filezilla Server (Windows)

    - by sestocker
    I've set up a self signed certificate in FileZilla server and enabled FTP over SSL/TPS. When I connect from the client FileZilla, I am able to authenticate but cannot get a directory listing: Status: Connecting to MY_SERVER_IP:21... Status: Connection established, waiting for welcome message... Response: 220-FileZilla Server version 0.9.39 beta Response: 220-written by Tim Kosse ([email protected]) Response: 220 Please visit http://sourceforge.net/projects/filezilla/ Command: AUTH TLS Response: 234 Using authentication type TLS Status: Initializing TLS... Status: Verifying certificate... Command: USER MYUSER Status: TLS/SSL connection established. Response: 331 Password required for MYUSER Command: PASS ******** Response: 230 Logged on Command: PBSZ 0 Response: 200 PBSZ=0 Command: PROT P Response: 200 Protection level set to P Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is current directory. Command: TYPE I Response: 200 Type set to I Command: PORT 10,10,25,85,219,172 Response: 200 Port command successful Command: MLSD Response: 150 Opening data channel for directory list. Response: 425 Can't open data connection. Error: Failed to retrieve directory listing I have ports 21 and 50001 through 50005 open on the firewall. We are migrating servers - the 50001 - 50005 is one of the things that helped get FTPS working on the old server. I'm not sure this installation would use the same ports? What else could be the problem?

    Read the article

  • Apache2.2 not responding on Windows 7 desktop

    - by Adam
    Afternoon! I'm having some trouble with Apache2.2 on Windows 7. For over a year it's been running no problem, but all of a sudden requests have just stopped responding. They don't ever time out, the browser just keeps on waiting for a response, which makes me think it's something blocking communication with Apache. Interestingly though, if I stop Apache the requests fail immediately. The Apache service is running, and using netstat I can see it listening on port 80 as configured: TCP 127.0.0.1:80 0.0.0.0:0 LISTENING If I stop the Apache service, that line disappears. I have an entry within my hosts file for each VHost I'm trying, all pointing to 127.0.0.1. Each VHost is configured to *:80. Nothing however is getting recorded in the access or error (at debug level) log files. I've verified the file paths are correct, even though they were never changed. Neither is anything getting recorded within Windows' Event Log. The problem showed up when I added a new VHost and restarted, however I hadn't been using it for a couple of days prior so I don't believe it's the config change. I have performed a syntax check to be sure, and when starting from the command prompt no errors are reported there. I do have Windows Firewall running, however I've verified the Apache rule is correct and tried turning it off to ensure that wasn't the problem. I've reinstalled Apache, in the hope it might magically fix something using the default config, but still no joy. I've also tried using a different port. I'm completely lost for ideas now. Can anybody help? Cheers Adam

    Read the article

  • check_snmp warning & critical thresholds with negative values

    - by Oesor
    I'm querying some signal level values measured in dBm, and the SNMP host on the remove device reports the values as negative values, ie, -90 dBm. However, check-snmp seems to be incapable of dealing with negative numbers as part of its threshold values. If I specify the values as part of a collection of OIDs, it accepts the syntax but converts the snmp value to positive, thus always generating a WARNING/CRITICAL result: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::AverageReceiveSNR.0,DEVICE-MIB::CurrentNoiseFloor.0 -w 10:,~:-85 -c 15:,~:-80 -vvvv /usr/bin/snmpget -t 1 -r 5 -m ALL -v 1 [authpriv] 192.168.1.100:161 DEVICE-MIB::AverageReceiveSNR.0 DEVICE-MIB::CurrentNoiseFloor.0 DEVICE-MIB::AverageReceiveSNR.0 = INTEGER: 25 DEVICE-MIB::CurrentNoiseFloor.0 = INTEGER: -97 Processing line 1 oidname: DEVICE-MIB::AverageReceiveSNR.0 response: = INTEGER: 25 Processing line 2 oidname: DEVICE-MIB::CurrentNoiseFloor.0 response: = INTEGER: -97 SNMP CRITICAL - 25 *97* | DEVICE-MIB::AverageReceiveSNR.0=25 DEVICE-MIB::CurrentNoiseFloor.0=97 If I run it with a single OID, it gives me an error that the format is incorrect: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::CurrentNoiseFloor.0 -w ~:-85 -c ~:-80 -vvvv Range format incorrect And if I run it with no thresholds defined, it works properly and returns the right value. This makes the graphs correct, however it'll never generate a notification when out of range: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::CurrentNoiseFloor.0 -vvvv /usr/bin/snmpget -t 1 -r 5 -m ALL -v 1 [authpriv] 192.168.1.100:161 DEVICE-MIB::CurrentNoiseFloor.0 DEVICE-MIB::CurrentNoiseFloor.0 = INTEGER: -97 Processing line 1 oidname: DEVICE-MIB::CurrentNoiseFloor.0 response: = INTEGER: -97 SNMP OK - -97 | DEVICE-MIB::CurrentNoiseFloor.0=-97 What am I doing wrong here? How would I, for example, generate a CRITICAL when the noise floor is -80 dBm or higher, a WARNING when it's -85 to -80 dBm, and an OK when -85 dBm or lower? Do I have to write my own SNMP plugins when dealing with negative values?

    Read the article

  • SQL server agent job to execute SSIS package fails, package succeds if run manually

    - by growse
    I've got a SSIS package installed on a SQL server (SQL Server 2012). It's fairly simple and just fetches data from a remote data source and adds it into a local table. The remote connection string is using SQL server authentication, while the local connection is using Windows auth. The remote connection password is protected, and the package was imported setting the protection level to Rely on server storage and roles for access control. If I run the SSIS package manually, it works. If I run it from the command line using dtexec, it works. If I use runas to switch to the domain account that the SQL server agent is running under, and then run the package using dtexec, it works. If I create a SQL Agent job with a single step to run the package, it fails, providing very little detail as to what's going on. I'm guessing it's not able to get the password to log into the remote SQL server, because it fails very quickly. Also, if I tick 'log to table' and view the resulting file, I get the following: Description: ADO NET Source has failed to acquire the connection {0D8F2CD4-A763-4AEB-8B52-B8FAE0621ED3} with the following error message: "Login failed for user 'username'.". If I try to add the password in the connection string manually under data sources in the job step dialog, it refuses to save it, always seeming to remove the 'password' bit of the connection string. I thought that SQL server agent jobs always ran under the context of the account which the SQL server agent is running under. This account is a sysadmin on the local SQL server, and the package works using dtexec under that account, so why would it fail when trying to run as an agent job?

    Read the article

  • How to tell which process is hogging my CPU when they don't add up to 100%?

    - by endolith
    Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. The individual processes do not add up to 100%. I try killing lots of processes, but the overall usage continues to be 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, which is never anywhere near 100% CPU unless I'm doing something that requires it (like loading 32 Firefox tabs), after which it goes back to a normal idle level. It's not a new install or anything. There is no reason the processor should be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing every process, one at a time, until the problem went away, and killing vino-server finally fixed it, even though that process never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). But the question remains: How did a single process manage to use 100% CPU while top only showed that process at 5%? How do I identify culprits like this in the future? Looks like I'm not the only one who's had this problem: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

    Read the article

  • What does this mean: "SATP VMW_SATP_LOCAL does not support device configuration"?

    - by Jason Tan
    Can anyone tell me what this means in ESXi 5.1?: SATP VMW_SATP_LOCAL does not support device configuration I've googled it and I get a lot of results, but as yet all the pages that contain the string are discussing other matters. The storage array is a HDS HUS-VM and the hosts are HP b460c G8 blades with flex fabric and flex fabric VCs which I am in the process of commissioning and would like to get it started on the right foot - i.e. error and warning free! naa.600508b1001c56ee3d70da65f071da23 Device Display Name: HP Serial Attached SCSI Disk (naa.600508b1001c56ee3d70da65f071da23) Storage Array Type: VMW_SATP_LOCAL Storage Array Type Device Config: SATP VMW_SATP_LOCAL does not support device configuration. Path Selection Policy: VMW_PSP_FIXED Path Selection Policy Device Config: {preferred=vmhba0:C0:T0:L1;current=vmhba0:C0:T0:L1} Path Selection Policy Device Custom Config: Working Paths: vmhba0:C0:T0:L1 Is Local SAS Device: true Is Boot USB Device: false This is the same LUN: ~ # esxcli storage core device list -d naa.60060e80132757005020275700000016 naa.60060e80132757005020275700000016 Display Name: HITACHI Fibre Channel Disk (naa.60060e80132757005020275700000016) Has Settable Display Name: true Size: 204800 Device Type: Direct-Access Multipath Plugin: NMP Devfs Path: /vmfs/devices/disks/naa.60060e80132757005020275700000016 Vendor: HITACHI Model: OPEN-V Revision: 5001 SCSI Level: 2 Is Pseudo: false Status: degraded Is RDM Capable: true Is Local: false Is Removable: false Is SSD: false Is Offline: false Is Perennially Reserved: false Queue Full Sample Size: 0 Queue Full Threshold: 0 Thin Provisioning Status: unknown Attached Filters: VAAI_FILTER VAAI Status: supported Other UIDs: vml.020001000060060e801327570050202757000000164f50454e2d56 Is Local SAS Device: false Is Boot USB Device: false ~ #

    Read the article

  • simple apache2 reverse proxy setup not working

    - by Nick
    I know what proxy is (very high level), it's just I have never set up one, and it feels like I might be missing some big fat point here. My setup: client server (static IP), runs apache on port 80 proxy (has 2 network cards, one is on the clients network, the other one with a static IP on the server network), runs apache on port 80 I am trying to configure these three machines so that when client requests: http://proxy/machine1 It gets served server's pages at server root URL, i.e. http://server/ I can access client pages just fine. However, when I try accessing a page from the client machine, it simply gets redirected to server's IP address, which it clearly can't access since they are not on the same network: ... <meta http-equiv="REFRESH" content="0;url=http://server/machine1"></meta> <title>Redirect</title> ... My apache2 config is: LoadModule proxy_module /modules/mod_proxy.so LoadModule proxy_http_module /modules/mod_proxy_http.so ProxyRequests off <Proxy *> Order Allow,Deny Allow from all </Proxy> ProxyPass /machine1 http://server:80 <Location /machine1> ProxyPassReverse / </Location> What gives? Thanks!

    Read the article

< Previous Page | 456 457 458 459 460 461 462 463 464 465 466 467  | Next Page >