Search Results

Search found 15210 results on 609 pages for 'technical writing'.

Page 460/609 | < Previous Page | 456 457 458 459 460 461 462 463 464 465 466 467  | Next Page >

• Most cost efficient way to backup Subversion data to S3?

  - by sludge

  I'm looking at using S3 as an offsite backup repo for my Subversion database. When I dump my SVN database, it's about 10 gigabytes. I would like to avoid the charge of uploading that data repeatedly. The anatomy of this large file such that new changes to Subversion modify the tail of the file, with everything else staying the same. Because Amazon S3 does not allow you to "patch" files with changes, I will have to upload ten gigs every time I instantiate a backup after doing a simple submit to Subversion. Here are the options as I see them: Option 1 I am looking at duplicity which has --volsize which splits data over an amount of megs. Is it possible to split the Subversion dumps using this so further incremental backups are measured in megabytes? Option 2 Can I just backup the hot subversion repository? This seems like a bad idea if it is in the middle of writing a submit. However, I have the option of taking the repo offline between the hours of midnight and 4am. Each revision in my Berkeley DB uses a file as its record.

  Read the article

• Subdocument in Word won't save

  - by ChrisW

  Because I know Word has a history of not liking very large documents (my supervisor specifically told me not to use LaTeX... grr), I decided to learn the Master document / subdocument feature of Word when writing my PhD thesis. I have the title page / table of contents etc in the master document, and each chapter as a separate document. However, when I save the master document, it appears to save all the chapter documents apart from one (Chapter 4), for which it brings up the Save Document dialog box, helpfully with "Chapter4.docx" in the "Save as" box (n.b. Chpater4.dox is not open). Clicking save does nothing, and doesn't make the dialog box go away. Saving as a different document means that my changes aren't reflected in the same document. There must be some reason Word doesn't like this particular document but I've got no idea why - there's nothing special in it that isn't in any of the other chapters. I have tried closing all documents, renaming Chapter4.docx, opening the master document, expanding all documents, OKing the warning that Chapter4.dox does not exist, and inserting the 'new' document, but even when I save the master document it still won't save the new Chapter4 document. If anyone knows any reason why Word is acting like this (or if I'm doing anything stupid), I'll be eternally grateful (p.s. sorry for the long rambling message. It's late; I've been working on my PhD 4.5 years, I really really want to throw this computer out the window, and I hope people are kind enough not to downvote this question because of it's rambling nature!) Update With Word closed, I've tried to delete Chapter4.docx (having made a backup!) - but I get a warning that it can't be deleted because it's open in Microsoft Word... these files are on a network drive and the same problems are happening on 2 different computers. I could login to the filestore through ssh and force the file to be deleted, but I'm curious to know why this is happening!

  Read the article

• Upstart can't determine my process' pid

  - by sirlark

  I'm writing an upstart script for a small service I've written for my colleagues. My upstart job can start the service, but when it does it only outputs queryqueue start/running; note the lack of a pid as given for other services. #/etc/init/queryqueue.conf description "Query Queue Daemon" author "---" start on started mysql stop on stopping mysql expect fork env DEFAULTFILE=/etc/default/queryqueue umask 007 kill timeout 30 pre-start script #if [ -f "$DEFAULTFILE" ]; then # . "$DEFAULTFILE" #fi [ ! -f /var/run/queryqueue.sock ] || rm -rf /var/run/queryqueue.sock #exec /usr/local/sbin/queryqueue -s /var/run/queryqueue.sock -d -l /tmp/upstart.log -p $PIDFILE -n $NUM_WORKERS $CLEANCACHE $FLUSHCACHE $CACHECONN end script script #Originally this stanza didn't exist at all if [ -f "$DEFAULTFILE" ]; then . "$DEFAULTFILE" fi exec /usr/local/sbin/queryqueue -s /var/run/queryqueue.sock -d -l /tmp/upstart.log -p $PIDFILE -n $NUM_WORKERS $CLEANCACHE $FLUSHCACHE $CACHECONN end script post-start script for i in `seq 1 5` ; do [ -S /var/run/queryqueue.sock ] && exit 0 sleep 1 done exit 1 end script The service in question is a python script, which when run without error, forks using the code below right after checking command line options and basic environmental sanity, so I tell upstart to expect fork. pid = os.fork() if pid != 0: sys.exit(0) The script is executable, and has a python shebang. I can send the TERM signal to the process manually, and it quits gracefully. But running stop queryqueue claims queryqueue stop/waiting but the process is still alive and well. Also, it's logs indicate it never received the kill signal. I'm guessing this is because upstart doesn't know which pid it has. I've also tried expect daemon and leaving the expect clause out entirely, but there's no change in behaviour. How can I get upstart to determine the pid of the exec'd process

  Read the article

• How to change the spell checking language in Chromium?

  - by mote

  When write I need spell checking in Danish or English (one at a time, not both at the same time), but changing from one language to the other is not working well for me. Example: Writing an email in English, everything is underlined as misspelled because the spelling language is set to Danish. I then right-click the text field and choose "Spell-checker Options" and set the language to English. But is does not change the language. Only after I try maybe 4-5 times it does. Selecting the text, clicking it, clicking the background, click the text, I have tried it all but I cannot figure out how it works. Sometimes it changes on first try, sometimes I have to do it 6-7 times. Searching brings lots of a known bugs stating that Chromium does not re-check the text after changing the language. But that is not what drives me crazy, for starters being able to change the language in the first try would be nice. It is not a fault in my installation, I have the same problem on 3 computers. Does any know something that I don't?

  Read the article

• Broad Band LAN connection through existing 6 wire phone line ( no phone connected )

  - by Paul Taylor

  I have an (up to but never achieved ) 10 mb broadband signal coming into my house along the telephone line. The modem then connects the broadband signal via a LAN connection and Wi-Fi signal to my computers and iPad. My workshop desk is 54 yards (approx. 50m) downhill from the modem (part of a separate building) – too far to give a good direct signal. The inside corner of the workshop (by a window) receives a weak signal. I have a disconnected telephone cable consisting of 6 wires going from the house to the workshop. The telephone is no longer used in the workshop - we use our mobile number for business calls. A broad band signal using the cable would not have to share with a phone. What would be the most economic price/efficient way to get the broadband signal to the workshop? I am writing in hope that since the telephone didn't need the six wires, an Ethernet connection might be similar and not need all the eight wires for a LAN connection. In theory could use the telephone wire to pull an Ethernet cable trough the underground pipe but I doubt if the cable would survive the strain. The broad band connection in the workshop does not have to have network facility. My skill level is high enough to do house wiring, plumbing and gas fitting; so given any sound advice and a wiring diagram or instructions I can probably work out the rest myself.

  Read the article

• Legal IT documents

  - by TylerShads

  I have been wondering this past week because my big boss told me to start keeping track of all the things I have fixed, how to fix them, etc. Which is reasonable and have been doing anyway. But then a related question came to mind. What kind of documentation should I have on hand as far as users go. More specifically I am talking in terms of EULA, ToC, etc (correct me please if I'm using the wrong terms) Or more specifically a policy, so to speak, for the users and such. Can't say I'm a legal expert, otherwise I'd be a lawyer. The environment the users are in is pretty laid back so I don't forsee a problem. But assume that there should ever arise a problem, what should I have written up/have on hand? EDIT: I really should have noted that we are a medical transport facility and have patient records so I know that something must be done there to comply with HIPAA policies I believe. I do like what anthonysomerset said about the "If I get by a bus" Scenario and want to apply it not only to the documentation I am currently writing but also for if say an employee were to steal info from the server or edge cases, theft, etc. As far as our staff, its relatively small as in a single HR person, no legal department aside from the 2 owners' lawyers and me being the only IT person on staff with a guy who is no more than a mac superuser.

  Read the article

• Can't install xclip on Ubuntu 10.10

  - by wildster

  I'm trying to load an SSH key to Github from a new machine and this command is not working: sudo apt-get install xclip Reading package lists... Done Building dependency tree Reading state information... Done Package xclip is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package xclip has no installation candidate when I try: sudo aptitude install xclip Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done No candidate version found for xclip No candidate version found for xclip The following partially installed packages will be configured: synaptics-dkms 0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0B of archives. After unpacking 0B will be used. Writing extended state information... Done Setting up synaptics-dkms (1.1.1) ... Loading new synaptics-1.1.1 DKMS files... Error! Cannot locate /usr/src/synaptics-1.1.1.dkms.tar.gz. File does not exist. dpkg: error processing synaptics-dkms (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: synaptics-dkms E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up synaptics-dkms (1.1.1) ... Loading new synaptics-1.1.1 DKMS files... Error! Cannot locate /usr/src/synaptics-1.1.1.dkms.tar.gz. File does not exist. dpkg: error processing synaptics-dkms (--configure): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: synaptics-dkms Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Any idea how I can install this? Mucho thanks in advance

  Read the article

• How to reject messages to unknown user in sendmail cooperating with MS-Exchange?

  - by user71061

  Hi! I have an MS Exchange 2003 configured as a mail server for an organization. As this server is located in this organization internal network and I don't want to expose it directly over internet, I have second server - linux box with sendmail - configured as intelligent relay (it accept all messages from internet addressed to @my_domain, and forward it to internal Exchange serwer, and accepts all messages from this internal Exchange server and forward it over internet). This configuration work's fine, but I want to eliminate messages addressed to not exiting users as early as possible. Good solution could be Enabling on Exchange server function of filtering recipients together with "tar pitting", but in my case this dosn't solve problem, because before any message reach my Exchange server (which could eventually reject it), it has to be already accepted by sendmail server, sitting in front of this Exchange server. So, I want to configure my sendmail server in such a way, that during initial SMTP conversation it could query somehow my Exchange server checking whether recipient address is valid or not, and based on result of this query, accept or reject (possibly with some delay) incoming message in a very early phase. In fact, I have already solved this issue by writing my own, simple sendmail milter program which checks recipient address against text file with list of valid addresses. But this solution is not satisfying me any longer, because it requires frequent updates of this file, and due to lack of time/motivation/programming skills, I don't want to cope further with my source code, adding to it functionality of querying my Exchange server. Maybe I can achieve desired effect by configuring any component of already available linux software. Any ideas?

  Read the article

• Files deleted. What could have happened?

  - by jjfine

  I'm having a weird issue today. I was writing and testing out some simple cgi scripts this morning when I realized that I couldn't run them from one of the other computers on the (windows) network. So I had my network admin come in and take a look at what was going on. A few minutes later a co-worker came in and told me that a bunch of files he was working with as well as a bunch of others (all *.c files) on the network drive got deleted. He also noticed some strange apache_dump_500.log.txt files in the same directories where the files got deleted. The apache_dump_500.log.txt files all look like this: REDIRECT_HTTP_ACCEPT=*/*, image/gif, image/x-xbitmap, image/jpeg REDIRECT_HTTP_USER_AGENT=Mozilla/1.1b2 (X11; I; HP-UX A.09.05 9000/712) REDIRECT_PATH=.:/bin:/usr/local/bin:/etc REDIRECT_QUERY_STRING= REDIRECT_REMOTE_ADDR=<my computer's local ip> REDIRECT_REMOTE_HOST= REDIRECT_SERVER_NAME=<my computer's domain url> REDIRECT_SERVER_PORT= REDIRECT_SERVER_SOFTWARE= REDIRECT_URL=/cgi-bin/trojan.py I looked and I don't have any trojan.py in my cgi-bin folder. And all my apache logs are clean. Windows event logger seems to not have any traces of what happened either. My httpd.conf: http://pastebin.com/Yny2Yh8v I think we've got some kind of virus that added this trojan.py file to my cgi-bin, ran the script, and deleted the script and any traces from the logs. Is this a thing that happens? Any ideas whatsoever would be much appreciated!

  Read the article

• EFS Remote Encryption

  - by Apoulet

  We have been trying to setup EFS across our domain. Unfortunately Reading/Writing file over network share does not work, we get an "Access Denied" error. Another worrying fact is that I managed to get it working for 1 machine but no other would work. The machines are all Windows 2008R2, running as VM under ESXi host. According to: http://technet.microsoft.com/en-us/library/bb457116.aspx#EHAA We setup the involved machine to be trusted for delegation The user are not restricted and can be trusted for delegation. The users have logged-in on both side and can read/write encrypted files without issues locally. I enabled Kerberos logging in the registry and this is the relevant logs that I get on the machine that has the encrypted files. In order for all certificate that the user possess (Only Key Name changes): Event ID 5058: Audit Success, "Other System Events" Key file operation. Subject: Security ID: {MyDOMAIN}\{MyID} Account Name: {MyID} Account Domain: {MyDOMAIN} Logon ID: 0xbXXXXXXX Cryptographic Parameters: Provider Name: Microsoft Software Key Storage Provider Algorithm Name: Not Available. Key Name: {CE885431-9B4F-47C2-8415-2D766B999999} Key Type: User key. Key File Operation Information: File Path: C:\Users\{MyID}\AppData\Roaming\Microsoft\Crypto\RSA\S-1-5-21-4585646465656-260371901-2912106767-1207\66099999999991e891f187e791277da03d_dfe9ecd8-31c4-4b0f-9b57-6fd3cab90760 Operation: Read persisted key from file. Return Code: 0x0[/code] Event ID 5061: Audit Faillure, "System Intergrity" [code]Cryptographic operation. Subject: Security ID: {MyDOMAIN}\{MyID} Account Name: {MyID} Account Domain: {MyDOMAIN} Logon ID: 0xbXXXXXXX Cryptographic Parameters: Provider Name: Microsoft Software Key Storage Provider Algorithm Name: RSA Key Name: {CE885431-9B4F-47C2-8415-2D766B999999} Key Type: User key. Cryptographic Operation: Operation: Open Key. Return Code: 0x8009000b Could this be related to this error from the CryptAcquireContext function NTE_BAD_KEY_STATE 0x8009000BL The user password has changed since the private keys were encrypted. The problem is that the users I using at the moment can not change their password.

  Read the article

• While loop read multiple lines from a grep

  - by Basil

  I'm writing a script in AIX 5.3 that will loop through the output of a df and check each volume against another config file. If the volume appears in the config file, it will set a flag which is needed later in the script. If my config file only has a single column and I use a for loop, this works perfectly. My problem, however, is that if I use a while read loop to populate more than one variable per line, any variables I set between the while and the done are discarded. For example, assuming the contents of /netapp/conf/ExcludeFile.conf are a bunch of lines containing two fields each: volName="myVolume" utilization=70 thresholdFlag=0 grep volName /netapp/conf/ExcludeFile.conf | while read vol threshold; do if [ $utilization -ge $threshold ] ; then thresholdFlag=1 fi done echo "$thresholdFlag" In this example, thresholdFlag will always be 0, even if the volume appears in the file and its utilization is greater than the threshold. I could have added an echo "setting thresholdFlag to 1" in there, see the echo, and it'll still echo a 0 at the end. Is there a clean way to do this? I think my while loop is being done in a subshell, and changes I make to variables in there are actually being made to local variables that are discarded after the done.

  Read the article

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• HTTP request hangs for for exactly 150 seconds, then gives incomplete response. How do I find out wh

  - by Nathan

  I am hosting a Wordpress blog, and having a strange problem. When I connect to the server (http://71.65.199.125/ at the time of this writing) it displays the Title correctly, and half of a download bar, indicating it has received some of the page, then it hangs for exactly 150 seconds (timed it twice), then it sends the rest of the page, but without the stylesheet. after that it hangs indefinitely, continuing to say "connecting..." without making any progress. If you have any clues as to what might be happening, or how I could print debug logs of PHP or something to see what it is looking for during that hang time that would probably help. recent changed I have made: switched wordpress themes, however I did see it work once with the new theme. moved the server to another building, with an identical ISP, and linksys router forwarding setup. I have also added a favicon.gif file to /var/www but without linking to it from any of the wordpress pages. I have also had a unanticipated power interruption. System info: Ubuntu debian 9.04 Apache2 PHP 5 Wordpress 2.9.2 Thank you

  Read the article

• What should be monitored to troubleshoot file sharing problems?

  - by RyanW

  I'm running into some problems with a file share used by an ASP.NET web application. With this configuration, there are 2 web servers (win2k8 web) that connect to a file server (win2k8 enterprise), reading and writing files using a file share. Recently, one of the web servers has begun encountering an error accessing the file share: IOException: The specified network name is no longer available. There does not appear to be much info on the web for explaining what's causing this and how to best fix it, so I'm looking at what I can monitor in order to get clues. I'm not sure if it's hardware, just a load issue, file size, frequency, etc. With Windows perfmon, what can I monitor on the File Server side? There's the "Files Open" object, any other good ones? What can I monitor on the web server side? EDIT: I'll add that the UNC path uses the IP address of the file server, not a name to resolve. Also the share is a single, flat directory with over 100K files.

  Read the article

• Map a URL bought with Dreamhost to Amazon EC2 (AWS)

  - by Edan Maor

  I have several URLs I purchased through Dreamhost. I'm starting to use Amazon's AWS, and I'd like to map the URLs to Amazon. This is something of a silly question, and I've already done the same thing several times to other services (mapping from Dreamhost to WebFaction). But for some reason when I tried to find the proper way to do the same mapping to Amazon, I find a lot of detailed writing talking about whether I should be using CNAME or A records, etc. So I wanted to ask in the simplest possible terms and hopefully get a simple, concrete answer: I bought a URL from Dreamhost, I have an EC2 server running on AWS (to which I already mapped an Elastic IP address). How do I make the URL map to AWS? And if there are several options, which one should I effectively be using? P.S. Meta-question - why are things so much more difficult with AWS? When I search Google for "Move from Dreamhost to WebFaction, I get very simple answers on how to do the mapping. In what way is AWS different?

  Read the article

• auto-mounting shared folders in VirtualBox

  - by brannerchinese

  I am writing to ask what the effect of the auto-mounting process is in VirtualBox, and where the folders can be accessed within a guest Linux system if auto-mount is used. I have VirtualBox 4.0.4 installed on Mac OS 10.6.7, with Guest Additions apparently running correctly. The guest OS is Ubuntu 10.04, and I observe no apparent problems with it. I find that if the shared folders have "auto-mount" unchecked in the VirtualBox settings, they can then be mounted using the prescribed syntax sudo mount -t vboxsf folder_name path_to_mount_point and all works as it is supposed to. But if the auto-mount option is checked, then I find that I can no longer mount the shared folders manually. I get the error mounting failed with the error: Invalid argument and the folders also do not appear to mount anywhere else accessible to me. Using the syntax sudo mount -t vboxsf without specifying a path installs them in /media, with their names prefixed with sf_, but they are not easily accessible there and I have not been able to change their owner using chown, either. Thanks for your patient explanation.

  Read the article

• Sudden problems with iptables not running

  - by Fourjays

  I've got a sudden issue with iptables not running on my CentOS 5.8/DirectAdmin XenVPS. All I have done today is install PHP APC and run an update (although I admittedly didn't pay much attention today - I usually do). Iptables has been running fairly smoothly since I installed it over 6 months ago. Basically when I try to run iptables -L it tells me: iptables v1.3.5: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. I've looked around and tried a few things and it appears that maybe my kernel doesn't have the modules loaded? I've been reading this and tried the two commands they suggest to no avail. Except there does appear to be a mismatch on one bit of output: -bash-3.2# cd /lib/modules -bash-3.2# ls 2.6.18-194.32.1.el5xen 2.6.18-238.5.1.el5xen 2.6.18-274.7.1.el5xen 2.6.39.1-cs-domU 2.6.18-238.12.1.el5xen 2.6.18-238.9.1.el5xen 2.6.37.2-cs-domU 3.0.1-cs-domU -bash-3.2# depmod -a WARNING: Couldn't open directory /lib/modules/2.6.18-274.18.1.el5xen: No such file or directory FATAL: Could not open /lib/modules/2.6.18-274.18.1.el5xen/modules.dep.temp for writing: No such file or directory Does this mean the versions are out of sync? If so, what are my next steps to getting this fixed? As you can probably tell I am still learning how to manage my server so please be very clear in all advice. Many thanks :)

  Read the article

• Best console based text editor not only for programmers [closed]

  - by robo

  I need console based text editor for writing both source codes and human readable texts such as emails. I need it to be user friendly. It mean for me: You can use it the same way as the notepad or gedit. You can use mouse there. If you need your mother of girlfriend or somebody to edit your text they will know what to do, they will not realize it is a console and will have only a feeling it is something like a notepad. copy, paste, undo works as usual with usual key combinations (Ctrl-C, Ctrl-V, Ctrl-Z). shift and arrows works as usual. They select the text. And when I return to the computer I want to use the text editor for programming. I expect: Syntax highliting auto indenting replacing spaces with tabs keyboard shortcuts for compiling possibility to configure it to use a debugger autocompletions for c#, java, c++ and other languages other things I expect from IDE's. I was working and configuring vim for a few years. But It never fulfilled all of my expectations (but it almost did). I thing I could get vim configured perfectly if I had few more weeks time for configurating it. Unfortunately I cannot afford to be configuring vim forever. Is there other alternative? Hopefully some editor I once set up and it will works forever? What do you use? I often hear people are using emacs. Is it worth learning?

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• 2 Printers 1 Queue

  - by Shazburg

  My issue: When an order is processed, the same document needs to be printed on two printers. My proposed solution: Create a single queue in CUPS with a backend script that spits the job out to the two real printers queues. My problem: Documentation. Maybe I'm looking at every ring around the bullseye, but I can't find anything that lays out the rules for writing a CUPS backend script. In the end, I have several questions: Is there already an option to do this in CUPS that I've missed? The line I use to add my queue is "lpadmin -p MultiPass -E -v multipass -P Generic PostScript Printer". But DeviceURI is bad unless I specify a directory like "-v multipass:/tmp". Why is this? For testing, my script does nothing but capture ARGV and write it out to a text file one line per argument. Problem is, I'm getting nothing. Logs show the job as successful, but I'm pretty sure my meager attempt at a backend isn't even being run. I've tried to keep this question brief, so please ask for more info as I'm sure I've left out the most important part in all this. Honestly, I'm just done chasing my own tail. Thank you for your time.

  Read the article

• Fast extraction of a time range from syslog logfile?

  - by mike

  I've got a logfile in the standard syslog format. It looks like this, except with hundreds of lines per second: Jan 11 07:48:46 blahblahblah... Jan 11 07:49:00 blahblahblah... Jan 11 07:50:13 blahblahblah... Jan 11 07:51:22 blahblahblah... Jan 11 07:58:04 blahblahblah... It doesn't roll at exactly midnight, but it'll never have more than two days in it. I often have to extract a timeslice from this file. I'd like to write a general-purpose script for this, that I can call like: $ timegrep 22:30-02:00 /logs/something.log ...and have it pull out the lines from 22:30, onward across the midnight boundary, until 2am the next day. There are a few caveats: I don't want to have to bother typing the date(s) on the command line, just the times. The program should be smart enough to figure them out. The log date format doesn't include the year, so it should guess based on the current year, but nonetheless do the right thing around New Year's Day. I want it to be fast -- it should use the fact that the lines are in order to seek around in the file and use a binary search. Before I spend a bunch of time writing this, does it already exist?

  Read the article

• Windows Server - share files without access for administrator

  - by Pawel

  We have a MS Windows Server 2008 R8 based server that is administrated by our IT department. We would like to achieve two things simultaneously: A folder on the server, containing several thousand files (new files added frequently) that is accessible to some ActiveDirectory users (e.g. board of directors) but is not accessible by IT department employees IT department employees still maintain rights to administrate the server, including installing new software and services We already checked some solutions: Using NTFS access rights. Unfortunately IT (members of "Administrators" group) can set themselves as new owners of the files and change the permissions so that they gain access to the files. Enabling EFS. Unfortunately even if you do not allow IT to access files, they still can disable EFS completely because they have administrative rights. Moreover as far as I know you have to manually add permissions for all users but the owner for each new file - very inconvenient. Creating a new role for the IT department that has all the privileges apart from taking ownership of files. Unfortunately if you're not a member of the Administrators group, you cannot install new software, no matter what privileges you add to the role. TrueCrypt - nice free encryption software, but with poor sharing capabilities. You can either mount an encryption container on the server (and then IT has access to its contents) or you mount them locally but only one user can mount it for writing. AxCrypt - free encryption software that enables file-by-file encryption on the server. There are some disadvantages though - you have to manually encrypt each new file added. The files have their extensions changes. You can only set one password for all files (so all users have to know this one password). Any other ideas? Our budget is limited so enterprise-class software from Symantec or PGP would probably be not an option.

  Read the article

• How can I store logs and meet compliance requirements for free?

  - by Martin

  I am trying to keep long-term logs of an app in such a way, that it could plausibly demonstrated to third parties/court that the application has processed certain data at a given time. The data can be represented in XML or text format. A simple gzipped log is not plausible, as I may have added or modified data afterwards, whereas an external logging service would be an overkill. Cost is an issue, we are not dealing with financial data or so, but rather some simple user generated content, where some malicious users tried to blame the operator in the past when things escalated and went to court. My question: Is there some kind of signing software for Linux that signs each element of a log in such a way, that it can be easily shown that no element can be added or modified afterwards? Plug-Ins into some free Splunk Alternatives would be fine too. Ideally the software I am looking for should be under a GPL or similar license. I could probably achive something like this by using PGP/GPG sgning functions and including the previous elements signituares within the following element, but I would prefer to use some program where you do not have to argue about the validity of your own code. Note to mods: I am not asking this question on Stackoverflow, because I am not looking for writing own code for reasons described above. I think this question rather fits into serverfault than superuser, as server-side logging software is discussed rather here than on superuser.

  Read the article

• Difficult to point-and-click target with Apple Magic Trackpad?

  - by Andrew Swift

  My Magic Trackpad is great for most things involving dragging and gestures, but for simple point-and-click use it is starting to get really annoying. For example, my bank has a numeric code that I need to enter from a visual grid on the screen, by clicking on the six numbers in order. To do this is quite difficult with the Magic Trackpad. Idea 1: it is because when you start dragging on the touchpad, there is a brief delay before the mouse starts to move. The delay might be enough to screw up my anticipation of where the cursor is going to go. Idea 2: it may have to do with the cursor acceleration. If I move it a little, the cursor moves a little. If I move it a lot, it goes much faster. I have tried various settings in the preference pane, and although the cursor does move more or less quickly, it doesn't seem any more or less easy to hit a given target. As I am writing this post, I tried a brief experiment -- I chose a spot on the page (the bracket in the superuser logo) and tried to move the cursor there in one quick movement. It's extremely difficult, even though I've been using Macs and touchpads since 1999. There is something about the behavior of the trackpad that is making it impossible for me to learn how to accurately predict where the cursor will end up. Does anyone else have this problem?

  Read the article

• Internet in the router but not in the local network.

  - by TheMouse

  I have a PC and a laptop (Windows 7 - both) which should connect through router to Internet. The router is Linksys wrt120. My ISP is using PPPoE. I have connected the Internet cable to the router, clone the MAC of my PC, writing the username and the password for my Internet connection. After seconds the router has acquired IP from my ISP. I have used the administration panel of Linksys and with the help of the ping and tracert commands which are built into it - I can connect to the world, outside the network. The problem is when I try to connect the PC or the laptop to the network. There's no problem here. The DHCP server of the router gives them appropriate addresses. The problem is that they couldn't connect to either Internet addresses (google.com) or IP addresses. But they can connect to the router and its control panel. I tried several times, reset the router..but there's no Internet..still.

  Read the article

< Previous Page | 456 457 458 459 460 461 462 463 464 465 466 467  | Next Page >