Search Results

Search found 29426 results on 1178 pages for 'user99572 is fine'.

Page 461/1178 | < Previous Page | 457 458 459 460 461 462 463 464 465 466 467 468  | Next Page >

• Catalyst Control Center removal

  - by Allan

  I've recently tested a graphics card on a machine that required different drivers than my onboard integrated graphics, so I had catalyst control center installed. After I pulled out the graphics card and went back to using the onboard graphics, I deleted the catalyst center through control panel - programs.. which was fine. But apparently it didn't really remove it. it doesn't show up under programs anymore but when I reboot windows I get an error saying "The catalyst Control Center is not supported by the driver version of your enabled graphics adapter" and its still in the process bar... how do I permanently remove it?

  Read the article

• Storage drives is causting system crash

  - by Chad

  I'm running Centos 5.4 with 750GB(ntfs) and 2TB drives for storage. Originally I installed the 750, everything seemed fine and then I installed the 2TB drive with NTFS already partitioned. I noticed when I would copy a lot of videos it would crash (no mouse or response from server) about 20min into it. After doing some troubleshooting I noticed the 750 would also crash when doing the same task so I decided that NTFS may be the problem. I unmounted the 2TB drive and tried to partition and format it using ext2 but when using parted it would crash at this point "writing inode tables". Looking at the dmesg logs I believe this is the error "mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining". Any idea as to what could be causing this?

  Read the article

• ASUS P5B Plus motherboard - no any drives found - how to restore RAID array?

  - by Moha

  We have a small server machine with an ASUS P5B Plus motherboard and 4 SATA HDDs. The HDDs were configured in a RAID10 array. Up until now, everything worked fine, but now the system doesn't recognize the drives. BIOS is set to RAID, jMicron controller is set to RAID, yet I can't see any of the drives in the BIOS setup, and jMicron BIOS tells me "no any drives found" The HDDs all spin up, I hear no clicking sounds or anything that would suggest HDD error. I did a search on this problem and replaced the SATA cables as suggested, but nothing's changed. What I have in mind is checking the CMOS battery and resetting the BIOS to use IDE mode, but I don't know if it will ruin the RAID system on the HDDs. It is not a critical server and there's only one database running on it (which I have backup of), but I don't want to setup the server from scratch if not necessary. What should I try to restore the RAID array and put the server back to working order?

  Read the article

• Can't print graphic from Publisher to pre-printed document

  - by Michael Itzoe

  I have a client who was given a stack of 8.5x11 tri-fold (unfolded) brochures printed on standard printer paper that they need to add their bulk mail permit stamp to. They've created a Publisher document with the stamp. If they print the document to standard paper in the tray, it prints fine. When they load the brochures into the tray, the brochure feeds through the printer but the stamp doesn't print. The stamp document is also 8.5x11. The printer is a Canon MF4300-D44. I can remoted in, but obviously have no access to the hardware. Any ideas?

  Read the article

• Sharepoint Document Library not receiving emails

  - by ria

  I have created a sharepoint document library which is email enabled. However when i send email to the designated email address from anywhere, i dont receive the email & attachment in the list. I have done some R&D and i hv found that in order to receive email from anywhere i have to expose my DNS of the sharepoint site to the outside world. Now i dont know whether it applies to the email address designated to me in the Active directory profile as well (my company domain email address). How to test that this email reception is working in the document library? I have tried sending an email from the sharepoint site and it works fine so the SMTP settings are correctly done.

  Read the article

• Opening firewall to incoming port 443

  - by jrdioko

  I recently set up the ufw firewall on a Linux machine so that outgoing connections are allowed, incoming connections are denied, and denied connections are logged. This seems to work fine for most cases, but I see many denied connections that are incoming on port 443 (many with IPs associated with Facebook). I can open that port to incoming connections, but first wanted to ask what these could be. Shouldn't HTTPS requests be initiated by me and be treated as outbound, not inbound connections? Is it typical to open incoming port 443 on consumer firewalls?

  Read the article

• why do I get this mail server configuration error?

  - by Francesco

  <<The configuration of your mail servers and your DNS are not ok! The report of the test is: mail.mydomain.com. -> mydomain.com -> 78.47.63.148 -> static.148.63.47.78.clients.your-server.de Spam recognition software and RFC821 4.3 (also RFC2821 4.3.1) state that the hostname given in the SMTP greeting MUST have an A record pointing back to the same server.>> I have a A Record that points mail.mydomain.com to 78.47.63.148 (which is my given ip address for my vps) All other records are fine, so what's wrong and what record should I create to make it right? Thanks

  Read the article

• After installing updates, Windows 7 reboots when it gets to "Preparing to Configure"

  - by Travis

  After letting Windows 7 Pro install updates at shutdown I now cannot get it to boot back up. I have tried selecting safemode, and "last known working configuration" and I get the same results. It gets to the screen and says "Preparing to configure Windows" and then reboots. If it is giving me a BSOD it is happening so fast I can not see it. This is a generic PC that has been running fine for the last year. It had 22 updates to do at shutdown. Windows 7 Pro Service Pack 1 64 bit in an Active Directory Domain.

  Read the article

• How do I make a Minecraft kiosk for portable USB drive that boots on most computers

  - by user2044589

  Some time ago, someone referred me to a cool website called Rapid Rollout. It worked fine until I tried to install an OS onto a netbook. To put it short, it didn't work as well as I expected it to. It also didn't install USB flash drives. I'm trying to build a system (or use a service that would create a system) that would open up the Minecraft Launcher (jar) and show it in full-screen with no background. It would also all have to fit into 8 Gigabytes (as this is the most that I can use right now). How can I accomplish this?

  Read the article

• Auto logon to internet provider

  - by user31673

  We use wireless internet access. The wireless is secured and to get an IP address, you provide the right key. That is setup just fine. However, on top of that, the first time we access the internet, a browser page appears and we have to enter a password. then we have access to the internet for a period of time. How can the password step be automated? I also have a web-based printer that doesn't work (except via USB connection) because it can't get out to the web. I can't change the router settings. Is there anything I can do to get the printer working and automatic the access?

  Read the article

• Java application not starting in Tomcat, Plesk 9 server

  - by netagence

  Hi I have a Plesk 9.3 CentOS 5 server on which I installed the addon to have Tomcat functions. One application I have uploaded appears in the Plesk Tomcat user panel but with a yellow exclamation mark and the error "Actual status of the application does not correspond to the status retrieved from the database". The app therefore does not run, while other uploaded test .war applications do. The server runs Tomcat tomcat5.5.23-0jpp.7.el5_2.1 which matches the requirements for the required app according the the company that made it. While searching for the solution I could find all 3 uploaded .war applications in /usr/share/tomcat5/psa-wars/domainhere.com/ but they do not seem uncompressed there even though 2 of them run fine. Not enough Tomcat / Java knowlede to go on... Any idea to help me here ? Best regards.

  Read the article

• High Lock Wait ratio in MySQL

  - by FunkyChicken

  on my site I log every pageview (date,ip,referrer,page,etc) in a simple mysql table. This table gets very little selects (3 per minute), but a lot of inserts. (about 100 per second) Today I changed this table from an InnoDB table to a MEMORY table, this made sense to me to prevent unnecessary hard disk IO. I also prune this table once per minute, to make sure it never get's too big. -- Performance wise, things are running fine. But I noticed that while running tuning-primer, that my Current Lock Wait ratio is quite high. Current Lock Wait ratio = 1 : 561 My question: Should I worry about this Lock Wait Ratio? And is there something I can change in my my.cnf to improve things so that the lock wait ratio isn't so high?

  Read the article

• Realtime file-level mirroring from local NTFS to network drive

  - by hurfdurf

  We have some data collection machines running WinXP. After a new file is written, we would like to immediately copy the new file to network storage (a NetApp CIFS share) automagically. We need realtime or near realtime copies generated (copy upon filehandle close would be fine -- these are not long-running system logs). Two commercial applications I've found so far are MirrorFile and IBM's Tivoli CDP. Are there any reliable open source programs or simple ways to get Shadow Copy to do something similar? Bonus points if it runs as a service.

  Read the article

• Mongo Scripting the shell

  - by cKendrick

  On my production stack, I have a front-end server and a Mongo server. I would like to be able to set a cron job on the front-end server to create some logs daily. I wrote a script that does this: ./mongo server:27017/dbname --quiet my_commands.js If I run it from the Mongo server as above, it works fine. However, I would like to be able to run it from the front-end server. When I try to do that, I get: -bash: mongo: command not found Since mongo is not installed on the front end server, it gives me that error. Is it possible to somehow bind mongo to my mongo on the Mongo server?

  Read the article

• Apache2 unable to start: private key not found

  - by user3161330

  today I edited some vhosts in my Apache installation and when I tried to restart it I got this error: [Sun Jun 08 15:20:19 2014] [error] Init: Private key not found [Sun Jun 08 15:20:19 2014] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag [Sun Jun 08 15:20:19 2014] [error] SSL Library Error: 218640442 error:0D08303A:asn1 encoding routines:ASN1_TEMPLATE_NOEXP_D2I:nested asn1 error [Sun Jun 08 15:20:19 2014] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag [Sun Jun 08 15:20:19 2014] [error] SSL Library Error: 218595386 error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error [Sun Jun 08 15:20:19 2014] [error] SSL Library Error: 67710980 error:04093004:rsa routines:OLD_RSA_PRIV_DECODE:RSA lib [Sun Jun 08 15:20:19 2014] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag [Sun Jun 08 15:20:19 2014] [error] SSL Library Error: 218595386 error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error I have tried to generate new self signed certificates issuing this command: openssl req -x509 -nodes -days 365 -newkey rsa:2048 -keyout server.cert.key -out server.cert.crt but the error still exists. The private key chmod is 600, and if I open it with nano looks, fine. I'm running Apache2 on a debian 7 machine.

  Read the article

• PHP 5.4.7 and Apache 2.2 Trouble under Windows XP

  - by IssamTP

  I'm trying to setup a test enviroment on a virtual machine running Windows XP Home (totally updated), with Apache 2.2 and PHP 5.4.7. I can load the PHP 5 module inside httpd.conf and if I don't rename php.ini-DEVELOPMENT (or -PRODUCTION) file to php.ini, the engine works fine. This basic configuration doesn't have MySQL module loaded, so I have to rename rename the .ini-DEVELOPMENT into .ini and edit as follows: ; Directory in which the loadable extensions (modules) reside. ; http://php.net/extension-dir ; extension_dir = "./" ; On windows: extension_dir = "C:/php/ext/" ... extension=php_mysql.dll extension=php_mysqli.dll Restart Apache with no problems and... all I can get is a blank page. Where can I see some error or do you know where is the trouble? Tell me if I need to post something else to give you more details.

  Read the article

• How do I get PHP to work with UserDir

  - by Callmeed

  I've got a fresh CentOS 5.5 box and have installed Webmin+VirtualMin 3.79. I've enabled UserDir in apache and the sites are visible via http://ipaddress/~user/ but PHP does not work. (PHP works fine if I visit the site via it's domain) Here's what I put in my httpd.conf to get where I'm at: <IfModule mod_userdir.c> UserDir public_html </IfModule> <Directory /home/*/public_html> Options -Indexes +IncludesNOEXEC +FollowSymLinks +ExecCGI allow from all AllowOverride All AddHandler fcgid-script .php AddHandler fcgid-script .php5 </Directory> When I try to hit a PHP file, I get a 500 error and the following is logged to /var/log/httpd/error_log: suexec failure: could not open log file fopen: Permission denied Any help/direction is appreciated.

  Read the article

• Windows 7 Won't connect to Wireless Router too far away (but still have 3 bars)

  - by Kerry

  I have found this problem a couple of times. Windows 7 with Intel AGN 5100 won't connect to a WPA2-PSK router when it's too far away. Both times I've had this happen I was in a foreign country (London and Stockholm), and both times I was upstairs while the router was downstairs. Now, it still has 2-3 bars when looking at local WiFi, but I get the "will not connect" error, and debugging doesn't help at all (it doesn't know what's wrong). I went downstairs and it connected immediately (but I need to be able to have it upstairs). My Android Cell Phone and iPad were able to connect upstairs just fine. Any suggestions?

  Read the article

• Why did my mouse/trackpad suddenly stop working on my MacBook under Windows XP?

  - by Jack B Nimble

  My mouse and track pad have suddenly stopped working on my MacBook, which is running Windows XP from BootCamp. Both the USB mouse and the trackpad work fine in OS X. The device manager says that the driver is missing or corrupt on both items (they have a yellow exclamation point). I tried uninstalling the mice, and reinstalling them. Since the USB mouse is a Logitech I tried replacing the driver with one downloaded from Logitech.com. Anyone know how I can repair the mouse driver that Windows XP is using?

  Read the article

• Setting Rails up on a Linode - Nginx Issue

  - by rctneil

  I am extremely new to this so please don't shoot me down: I have set up a Linode running Ubuntu, It is all sort of working except Nginx. I am following this guide: http://rubysource.com/deploying-a-rails-application/ And this for nginx: http://library.linode.com/web-servers/nginx/installation/ubuntu-10.04-lucid When I go to my IP, I get a 500 internal server error. I have tried starting nginx and it looks like it starts fine. I run this: ps awx | grep nginx and I get: 308 ? Ss 0:00 nginx: master process /usr/sbin/nginx 2309 ? S 0:00 nginx: worker process 2311 ? S 0:00 nginx: worker process 2312 ? S 0:00 nginx: worker process 2313 ? S 0:00 nginx: worker process 2850 pts/0 S+ 0:00 grep --color=auto nginx I really am not sure what else to do to get it running. Any help? Neil

  Read the article

• Can't Read/Write the Hard disk used in NAS

  - by mgpyone

  I've lately purchased a Synology DS212j and I intended to use my two 3.5" HDs into it. One of them was in used as an external HD. Thus when I install these two unit in NAS, it asked me to formatted in order to used with its format (I think it's ext3?) . I installed the Disks and omit the formatting option. I just got another 3.5" Hard Disk now. I've installed it in the NAS. everything's fine. However, when I take out the (used) HD from the NAS and install back in the standalone casing, I found out that it can't be read from both OSX an Windows 7. I've tried with ext2sd and I only found 2GB portion of the whole 1.5 TB Hard Disk. Here's another reference from EASEUS Partition Master

  Read the article

• Why does Windows 7 x64 work faster than an x86 edition on my PC?

  - by Jasper

  Why does Windows 7 x64 work faster than an x86 edition on my PC even though I mostly use x86 things in it? What's wrong with me, and what am I missing? Majority of the things I use is x86 (e.g. DAWs, games, media players). A considerable amount of them, however, are x64 (although their x86 counterparts work just fine). I've tried using the same things on the same system but always ended up finding Windows 7 x64 working slightly faster than x86. I'm very observant. I even notice the tiniest window animations. System: Windows 7 Ultimate x64 CPU: Intel Core 2 Duo E7500 @ 2.93 GHz RAM: 2 GB x 2 = 4 GB DDR2 @ 332 MHz Motherboard: Intel D945GCNL Graphics: ATI Radeon HD 4350 @ 1 GB Dedicated Audio: M-Audio FastTrack Pro HDD: Samsung HD753LJ 733 GB & Samsung HD160JJ 156 GB As you can see, my system is old.

  Read the article

• grub2 error: out of disk

  - by Carl Smotricz

  I'm trying to make a 250G USB hard disk Ubuntu-bootable on a Compaq nc6220 laptop. I've removed all other disks, so /dev/sda (the USB disk) is the only disk other than CDROM. I installed Ubuntu 9.10 to this disk from the live CD, putting the bootloader on /dev/sda . The default system couldn't be booted, and nothing I did in the Grub menu/cmdline helped. So I chrooted onto the disk and did grub-install /dev/sda. That seemed to work fine, but Grub (1.97 beta 4) keeps coming up with error: out of disk Even when I drop to the command line to do something simple like ls or help, it's always the same error message. Any hints for resolving this, please?

  Read the article

• Image doesn't fill monitor when connected via HDMI

  - by russau

  Connecting a Dell Studio Slim to a Dell ST2210 21.5" monitor. The PC has a ATI Radeon HD 4350 video card. The video card has DVI and HDMI connections. When I connect with the DVI everything works fine. When I connect with the HMDI the image doesn't fill the screen, i.e. there's a approx 1 inch black border around the image. Win7 tells me the res is 1920x1080 (the native res of the monitor). Tried rebooting, no luck.

  Read the article

• Why do some devices seemingly need the wifi router to reboot before they can connect?

  - by CreeDorofl

  I've noticed a pattern but I'm not sure if it's a crappy router, crappy wireless device, or maybe everything is working as intended. I can wirelessly connect my office PC to the router's settings page for a day, maybe two, then afterwards I can't anymore until it's reset. Unrelated, but similar, in various places that offer free wifi, my kindle will connect fine most days, but occasionally won't unless the router is reset. After the reset, I connect ok. What's happening behind the scenes that makes a router stop allowing you to connect? Is it something on my end that's changing, or on the router's end?

  Read the article

< Previous Page | 457 458 459 460 461 462 463 464 465 466 467 468  | Next Page >