Search Results

Search found 12605 results on 505 pages for 'settings'.

Page 462/505 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

• Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

  - by Martin

  Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

  Read the article

• How should I use my new SSD drive?

  - by jasondavis

  I just built a new PC the other day. Specs... Processor: Intel i7-930 quad core CPU CPU Cooler: COOLER MASTER Hyper 212 Motherboard: AsRock X58 Extreme 3 RAM/Memory: 6gb G-Skill tripple channel DDR3 memory (3 sticks of 2gb planning to get another kit to make it 12gb total soon) Operating System Hard drive: Intel X25-M 80GB Mainstream SATA2 Solid State Drive Video Cards: 2 XFX ATI Redeon HD 4650 cards to run 3-4 monitors Case: Lian Li PC-B10 Midtower case Power Supply: Antec TruePower New TP-750 Blue 750W Operating System Windows 7 Pro 64bit Not sure if the specs are helpful at all but I posted them just in case. So I got everything put together and running great so far but I need some advice/ideas/help/tips. I got the SSD drive in hopes of using it strictly for my windows 7 install along with all my other programs I install. I am then going to get another drive or 2 just for data (video,music,photos, etc). So my plan is to just install the new data drives and then in windows 7 I will change my "My documents" "My Music" "My Video" "MY Photos" library's to be located on the data drives instead of the OS SSD drive. I would ultimately like to install all my programs with my windows install on the SSD drive and then create an IMAGE of the drive and then 6 months down the road if things are sluggish I can just wipe the drive and restore my IMAGE with all my programs and settings in tact still. So here are some questions now. 1) How can I verify that TRIM is working on my new SSD? 2) Is there anything above that I missed that I should be doing? I think I once read that there is a page file or some sort of file that windows changes a lot and that it should be moved off f an SSD an onto my data drives. DOes anyone know what I might of heard? If you do can you explain the pros and cons of doing such a thing as well as how to possibly? 3) Any tips or advice to get the best performance from all this, I built a pretty nice system and I just want to make it stay that way as long as I can.

  Read the article

• Suspected network performance issue on VirtualBox Ubuntu guest on Win7 host

  - by Adam

  I set up Ubuntu 12.04 in VirtualBox on the Win7 machine I was allocated on my new project. I am running Java, Eclipse, Tomcat to develop a large data-intensive application and I noticed that this application runs at half the speed of my colleague's identical machine, where he runs it all under Windows. I think I have narrowed down the performance issue to the network, after comparing and equalising all the Java VM settings with my colleague. Is there a ping test I can do or some other network diagnostic test to flag up any problems? To give some background, the network performance is confusing. Running a network speed test to my colleague's machine with iperf shows speeds of 6 Mb/s from my Ubuntu guest, and 90 Mb/s from the win7 host. Large downloads, e.g. the Java SDK, come down at about 1.2 MB/s on both the guest and the host. Pings are sub-1ms on the host, but 1.5ms on the guest. I also did a broadband speed test, and got 10Mb/s download speed on both, but the host has an upload speed of 10Mb/s but the guest only uploads at 3Mb/s. I've been trying to diagnose any MTU problems with ping -M do to identify any kind of packet fragmentation problem but it's progressing very slow because I don't have much experience in this area. From what I read on other people's networking issues with VB and Linux guests on Win7 hosts, I should be able to get the speed on the guest up to the same level as the host. I installed a fresh VM with Ubuntu again to see if I'd foobar'd it somehow, but I'm getting the same readings with iperf on the virgin installation. My setup is: Adapter 1: Intel PRO/1000 MT Desktop (NAT) Adapter 2: ditto (host-only adapter) eth0 Link encap:Ethernet HWaddr 08:00:27:0b:76:bf inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe0b:76bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86236 errors:0 dropped:0 overruns:0 frame:0 TX packets:49369 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:69163946 (69.1 MB) TX bytes:3530535 (3.5 MB) eth2 Link encap:Ethernet HWaddr 08:00:27:a3:26:b8 inet addr:192.168.56.101 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:26b8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:59 errors:0 dropped:0 overruns:0 frame:0 TX packets:57 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9148 (9.1 KB) TX bytes:7648 (7.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:701 errors:0 dropped:0 overruns:0 frame:0 TX packets:701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:66321 (66.3 KB) TX bytes:66321 (66.3 KB)

  Read the article

• "log on as a batch job" user rights removed by what GPO?

  - by LarsH

  I am not much of a server administrator, but get my feet wet when I have to. Right now I'm running some COTS software on a Windows 2008 Server machine. The software installer creates a few user accounts for running its processes, and then gives those users the right to "log on as a batch job". Every so often (e.g. yesterday at 2:52pm and this morning at 7:50am), those rights disappear. The software then stops working. I can verify that the user rights are gone by using secedit /export /cfg e:\temp\uraExp.inf /areas USER_RIGHTS and I have a script that does this every 30 seconds and logs the results with a timestamp, so I know when the rights disappear. What I see from the export is that in the "good" state, i.e. after I install the software and it's working correctly, the line for SeBatchLogonRight from the secedit export includes the user accounts created by the software. But every few hours (sometimes more), those user accounts are removed from that line. The same thing can be seen by using the GUI tool Local Security Policy > Security Settings > Local Policies > User Rights Assignment > Log on as a batch job: in the "good" state, that policy includes the needed user accounts, and in the bad state, the policy does not. Based on the above-mentioned logging script and the timestamps at which the user rights are being removed, I can see clearly that some GPOs are causing the change. The GPO Operational log shows GPOs being processed at exactly the right times. E.g.: Starting Registry Extension Processing. List of applicable GPOs: (Changes were detected.) Local Group Policy I have run GPOs on demand using gpupdate /force, and was able to verify that this caused the User Rights to be removed. We have looked over local group policies till our eyes are crossed, trying to figure out which one might be stripping these User Rights to "log on as a batch job." We have not configured any local group policies on this machine, that we know of; so is there a default local group policy that might typically do such a thing? Are there typical domain policies that would do this? I have been working with our IT staff colleagues to troubleshoot the problem, but none of them are really GPO experts... They wear many hats, and they do what they need to do in order to keep most things running. Any suggestions would be greatly appreciated!

  Read the article

• What's the best scenario for using a wireless router with Comcast Business Class

  - by Buck

  Just had Comcast Business Class internet installed (usage details at bottom of post). During the call to order I asked about the hardware they'd be providing and was told it was a docsis 3 modem that I'd have to pay $7.00/month for. Figuring I'd have to buy a router anyway, I decided to get my own modem - a Surfboard SB6121 Docsis 3. I called in to tech support to ask some questions and learned that the modem they would have provided DID have a router built in. It's an SMCD3G-CCR. It's not wireless (we need wireless). The guy explained that it was better to have their hardware here because if there's a problem with our service and we're using our own hardware, chances are they'll blame it on our hardware and do nothing since they don't support it. He explained that I could still hang my own wireless router off their modem/router and if we ever had any service problems, we'd be able to plug directly into their hardware and they'd be able to tell where the problem is and they wouldn't be able to pawn it off onto "customer provided equipment". That all said, a few questions: 1. Am I better off returning my Surfboard modem and getting the Comcast one? If I get a wireless router and plug into one of the ethernet ports of the Comcast device, should I NOT plug anything else into the Comcast device since it would be a different network from anything connecting via the wireless router? Is that correct? Given that I know VERY LITTLE about networking and setting up hardware like this... since I need wireless and will HAVE to get a wireless router to work with this Comcast device, do I need to do anything with the settings of the Comcast device? Do I use security on the Comcast device or the wireless router or both? Any suggestions or anything I need to think about, given this scenario, in order to use a business-type voip service like RingCentral or Jive or Nextiva? Any recommendations on a wireless router for this scenario? We are running 2 PCs (possibly 3-4 in the future) - could be wired for the time being if needed but would prefer wireless; would like to have a networked hard drive and a networked printer; NEED business-type VOIP service asap for 2 phone lines. Would like to hook up some IP cameras at some point (but not the kind that require static IPs since I don't have one nor do I plan to pay Comcast another $15/month for one). I don't have or plan to have any type of web servers or anything like that. Want to use WPA or WPA2 security and take advantage of the NAT feature of the router for additional protection (that's the extent of my networking knowledge).

  Read the article

• My network drive disappears from Mac OS Finder

  - by Mariusz

  I have recently bought a Netgear WNDR3800 router to use it in my home network. But just the same day I installed it, I noticed a strange behaviour of Finder and iTunes. Let me explain it further. There is a Synology DS111 NAS attached to that router and two Macs with Mac OS X Lion. One of them is connected by a cable and the second one wirelessly. Before I changed my router to the new one I mentioned above, Finder always used to display my NAS on its sidebar. So I could just click its network name to access shared folders existing on it. But after I installed WNDR3800, I can no longer access the NAS that way. It is no longer displayed. I always have to mount it manually by typing its IP address using the Finder's 'connect to server' option. The same NAS supports TimeMachine backups and has an inbuilt DLNA server. And the same situation here. I can't perform a backup because my NAS is no longer accessible in TimeMachine preferences. iTunes does not display it as well (as a multimedia server) even though it used to before I installed that router. What's important, everything works fine for a couple of minutes after I restart the router or the NAS. Or even when I change the NAS's IP address it becomes accessible again in Finder, TimeMachine and iTunes, but only for some time. Both the Mac computers I mentioned behave the same way. And all those issues have been taking place sice I installed that new router. Before I did that, everything had worked fine. My old router was Netgear WGR614v10. Would you be so kind to tell me what you think could possibly be the reason of that behaviour? What settings of the router should I look closer at? I'm not a network specialist, but is it possible that some network packets are blocked for some reason? I will be grateful for any clues you give me. Thank you.

  Read the article

• Ubuntu stopped recognizing my iPod

  - by flashnode

  Rythmbox on Ubuntu 10.10 used to recognize my 3rd gen Nano and transfer mp3s. Now I plug it in and Ubuntu doesn't pop-up that box that asks what you want to do anymore. It is only recognized if I reboot and the thing is plugged in. Here is the output to 'lsusb -v -s bus:device' Bus 001 Device 008: ID 05ac:1262 Apple, Inc. iPod Nano 3.Gen Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x05ac Apple, Inc. idProduct 0x1262 iPod Nano 3.Gen bcdDevice 0.01 iManufacturer 1 Apple Inc. iProduct 2 iPod iSerial 3 000A27001A670128 bNumConfigurations 2 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 149 bNumInterfaces 3 bConfigurationValue 2 iConfiguration 4 iPod USB Interface bmAttributes 0xc0 Self Powered MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 1 Audio bInterfaceSubClass 1 Control Device bInterfaceProtocol 0 iInterface 0 AudioControl Interface Descriptor: bLength 9 bDescriptorType 36 bDescriptorSubtype 1 (HEADER) bcdADC 1.00 wTotalLength 30 bInCollection 1 baInterfaceNr( 0) 1 AudioControl Interface Descriptor: bLength 12 bDescriptorType 36 bDescriptorSubtype 2 (INPUT_TERMINAL) bTerminalID 1 wTerminalType 0x0201 Microphone bAssocTerminal 2 bNrChannels 2 wChannelConfig 0x0003 Left Front (L) Right Front (R) iChannelNames 0 iTerminal 0 AudioControl Interface Descriptor: bLength 9 bDescriptorType 36 bDescriptorSubtype 3 (OUTPUT_TERMINAL) bTerminalID 2 wTerminalType 0x0101 USB Streaming bAssocTerminal 1 bSourceID 1 iTerminal 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 1 Audio bInterfaceSubClass 2 Streaming bInterfaceProtocol 0 iInterface 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 1 bNumEndpoints 1 bInterfaceClass 1 Audio bInterfaceSubClass 2 Streaming bInterfaceProtocol 0 iInterface 0 AudioStreaming Interface Descriptor: bLength 7 bDescriptorType 36 bDescriptorSubtype 1 (AS_GENERAL) bTerminalLink 2 bDelay 1 frames wFormatTag 1 PCM AudioStreaming Interface Descriptor: bLength 35 bDescriptorType 36 bDescriptorSubtype 2 (FORMAT_TYPE) bFormatType 1 (FORMAT_TYPE_I) bNrChannels 2 bSubframeSize 2 bBitResolution 16 bSamFreqType 9 Discrete tSamFreq[ 0] 8000 tSamFreq[ 1] 11025 tSamFreq[ 2] 12000 tSamFreq[ 3] 16000 tSamFreq[ 4] 22050 tSamFreq[ 5] 24000 tSamFreq[ 6] 32000 tSamFreq[ 7] 44100 tSamFreq[ 8] 48000 Endpoint Descriptor: bLength 9 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 1 Transfer Type Isochronous Synch Type None Usage Type Data wMaxPacketSize 0x00c0 1x 192 bytes bInterval 4 bRefresh 0 bSynchAddress 0 AudioControl Endpoint Descriptor: bLength 7 bDescriptorType 37 bDescriptorSubtype 1 (EP_GENERAL) bmAttributes 0x01 Sampling Frequency bLockDelayUnits 0 Undefined wLockDelay 0 Undefined Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 0 No Subclass bInterfaceProtocol 0 None iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.01 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 208 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 2 Device Status: 0x0000 (Bus Powered) This ubuntu forum told me to check the automount settings under /apps/nautilus/preferences/media_automount_open in gconf-editor. And I did that. Any clues?

  Read the article

• Can't validate mine, sudo nor root in Debian "Jessie" Gnome anymore?

  - by Janar

  I'm Debian beginner & GUI guy in a bit of trouble? Can't login as sudo/gksu/root/su nor as (main/super)user after removed user password via Gnome-user-settings. History of actions (Probably irrelevant though) Installed Debian "Jessie" GNU/Linux with xFce GUI (en-US) as only OS. HardWare is ThinkPad w510. Skipped root user password in setup, to get sudo for superuser easily. Logged in (as always had) with Gnome (3.4.x), not once with xFCE. (installed Xfce. Installed xFce only to achieve more control (easier management) over packages this way, to set-up gnome much more by mine likes. Added more jessie repros (same ones as in Wheesy stable by default but for Jessie as, Jessie only had repros for security updates by default). Installed lots of gtk(3) & gnome(3) based soft; (- restarted again after this) Installed propietary graphics card driver for mine nvidia quadro. (- restarted once again after that one) Installed more stuff related to mine work/school/devel. The actual problem Had a plan to restart again, but wanted to set up auto-login first, instead set user password to none (don't ask why / perhaps caused by being awake for a looooong time), noticed it, and set also to auto-login, but couldn't undo mine previous mistake to create new password for me. As mine password is set to none I would have expected that simply return in pass prompt for emty password field would do, but it won't authenticate. I tried Alt+F2 "gksu gedit" as well as: sudo wget "https://www.some-page.eu/file.ext" and "su" in terminals, none has applied (quite logical actually - as I'm sudoer and highest ranked super user, besides only user in computer). Current stand Everything worked & still works nice after this accident, besides this password prompts part. To spoked to log-out nor restart. Synaptic package-manager is still open with root rights (only one, that has left open prior to the issue and not closed since, just in case). Goggled for help and read some manuals/faqs/how-tos - mostly lead to sudoers file management, but not found one specifically for mine issue - so still not any smarter. Really hope, that I don't have to redo OS inst all over again, by just one stupid mistake. Thanks for your reply :-)

  Read the article

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• Windows7 issue in mutli- tasking and memory

  - by Nitesh

  I seeming some problem in my windows OS recently, let me first say my system configuration. processor - Intel(R) Core(TM)2 Quad CPU Q8400 @ 2.66 GHz Installed memory (RAM) - 4.00 GB (3.00 GB usable) System type - 32 bit operating system I am using two OS in this system, first one is Windows7 and the other is centOS. Well, I am using this from a long time there was no problem , and all of a sudden since from couple weeks I am facing problems in my Windows7 OS. In windows7 i was nearing using multiple jobs almost every time i log in, there was no problem but now i don't no what happen I am not able to do multiple jobs at same time. For example- 1 I am now not able to listen to music in windows media player and view photo's. All of a sudden the system stops working and does not respond and then respond after 5mins and the music get played where it got stopped after 5 mins. 2 When i start browersing internet it hangs all of sudden and doesn't respond for 2 or 3 mins and gets loading. I mean it just happens for every operation i do in the system. Even now typing was also difficult, it gets hanged very frequently even though i am doing single task. I have never come across this kind of problem before. So the first thing i did was to see the useage of the processor and the memory. Well, i thick the useage of the processor was fine, for single task the useage was some where around 3 to 5%. Well, it was something weird i found in the memory, in spite of no task that i was running it was using somewhere around 34 to 41% of memory. So i opened the task manager and click on resource monitor in performance tab. And in the memory section of the monitoring tool i found the usage of my RAM, it was something like this. Hardware reserved - 1029 MB In Use - 1430 MB Modified - 49 MB Standby - 1566 MB free - 22 MB And i could also see Available 1588 MB Cached 1615 MB Total 3067 MB Installed 4096 MB well, this if all i could find out and i have no idea why my computer is acting so weird all of a sudden and the performance problem is growing day by day and i also don't know if there is problem in Bios, i have let it for default settings from long time. please help me and Thank you in advance for reading this and helping me.

  Read the article

• I want to virtualize my workstation (Tier 1), Looking for Bare Metal Hypervisor for consumer grade components

  - by Chase Florell

  I find myself in this similar bind at least once a year. The bind whereby I'm either upgrading a motherboard, or an OS hard drive. It drives me crazy to have to reinstall Windows, Visual Studio, all my addins, reconfigure my settings etc... every single time. I have a layout and I like and I want to stick with it. My question is... Is there a Bare Metal Hypervisor on the market that will enable me to virtualize my consumer grade workstation? I really want to avoid Host/Client virtualization. Bare Metal is definitely a better way to go for my needs. Is this a good approach, or am I going to suffer some other undesirable side effects by doing this? Clarification My machine has very limited purposes. My primary use is Visual Studio 2010 Professional where I develop ASP.NET MVC Web Applications. The second piece of software that I use (that's system intensive) is Photoshop CS3. Beyond that, my applications are limited to Outlook, Internet Explorer, Firefox, Opera, Chrome, LinqPad, and various other (small) apps. Beyond this, I'm considering working on a node.js project and might run ubuntu on the same hypervisor if possible. System Specs: Gigabyte Motherboard Intel i7 920 12 GB Ram basic 500GB 7200RPM HDD for OS 4 VelociRaptors in Raid 1/0 for build disk Dual GTS250 (512MB) Graphics cards (non SLI) for quad monitors On a side note I also wouldn't be opposed to an alternative suggestion if the limitations are too great. I could install the ESXi (or Zen Server) on my box, and build a separate "thin client" to RDP into the virtual machine. It appears as though RDP supports dual monitors. Edit (Dec 9, 2011) It's been nearly a year since I first asked this question. Since then, there have been a lot of great strides in Hypervisor technology... AND MokaFive is now released for corporate use. I'd love to dig into this question a little more and find out if there is a solid BareMetal Hypervisor for workstations running consumer grade components (IE: not Dell, HP, Lenovo, Etc).

  Read the article

• Can this USB3 behaviour be anything else than a hardware failure?

  - by Jonas Wielicki

  While my motherboard is half a year old now (ASUS M5A99X EVO), I only recently made use of the USB3 boards (after purchase of USB3 external harddrive). However, I am encountering issues. I am running linux 3.6.7-4.fc16.x86_64. Initially, the harddrive worked fine with USB3 (amazing ˜160MB/s), but I had some problems after putting after putting the harddrive to sleep manually after use (backup) with hdparm -Y. After some time, the device disappears from lsusb and i see the following in dmesg: [ 1924.091107] xhci_hcd 0000:05:00.0: xHCI host not responding to stop endpoint command. [ 1924.091114] xhci_hcd 0000:05:00.0: Assuming host is dying, halting host. [ 1924.091147] xhci_hcd 0000:05:00.0: HC died; cleaning up [ 1924.091233] usb 11-1: USB disconnect, device number 2 [ 1924.091272] sd 6:0:0:0: Device offlined - not ready after error recovery Testing with my (USB3 capable) notebook, I could not immediately reproduce the behaivour. I put the drive to sleep with hdparm -Y and waited for like an hour, but it was still listed in lsusb and responded after a few seconds delay when I tried after the hour of waiting. After an hour, on the desktop, the device would've usually vanished. Googling for this issue, I came across hints that playing around with IOMMU settings and upgrading the BIOS might help. I upgraded the BIOS and tried both with and without IOMMU enabled, got similar results. Most disturbing is, that one of the two USB 3.0 hubs sometimes also disappears from lsusb (or does not show up after boot at all). I've also heard that there are some hardware issues with ASUS USB3 ports. Applying mechanic force to the capble doesn't push the issue to one side or the other. Also, udev seems to reenumerate all devices if I plug the HDD into the USB 3.0 port without success (I can notice from my keyboard layout being changed to the default, which I do not use normally). The drive is externally powered and the external power supply is plugged in (it also stays powered when unplugging from USB, although it will spin down then). So before I try to return the board, I wanted to find out whether this can be anything else than a failure on the motherboard?

  Read the article

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

• Alienware m15x (older model) BSOD investigation

  - by Crishu

  A frined of mine asked me to help him with an Alienware m15x laptop that had a little service history. It was bought in june 2008, serviced in january 2009 for a random fps drop problem, Alienware returned it saying nothing was wrong. The laptop still had hiccups, but after juggling a few drivers and settings, the fps drops weren't as noticeable. Eventually it died in Sept. 2009. It would not boot up locking itself on a white/gray screen. (i think it was overheating .. clocking in 100 degrees Celsius). So back to Alienware it went. They replaced the GPU and all was fine. Up until these blue screens started showing up. One other thing that was updated was the HDD and a Windows 7 reinstall, in August. From then on it seems to have started its BSOD. Could this be the culprit? Why? 0_o The original Windows was Vista but it was upgraded with a digital download/purchase of Windows 7 Home Premium and activated after installing windows. No errors on the old HDD, just on the latest installation. LE:Due note that now the old HDD is used to see if issues re-occur. So please, I am in need of someone who can interpret these windows dump files: Minidump I may have come to some conflicting conclusions. So if someone can clarify each dump/date and the probable cause/error it had; and a final conclusion or solution, we would be very grateful. Also please consult report for other system info I omitted: same link,code: XRWIVLWG If I missed something or if you have any other questions I'll be happy to answer them. Thank you. Good day. Processor: Intel(R) Core(TM)2 Duo CPU T9300 @ 2.50GHz Network Adapter Properties: Broadcom NetLink (TM) Gigabit Ethernet Intel(R) Wireless WiFi Link 4965AGN Video Adapter Properties: Driver Description NVIDIA GeForce 8800M GTX Driver Date 19.08.2009 Driver Version 8.16.11.8681 Driver Provider NVIDIA INF File oem19.inf Hardware ID PCI\VEN_10DE&DEV_060C&SUBSYS_0770152D&REV_A2 Location Information @system32\DRIVERS\pci.sys,#65536;PCI bus %1, device %2, function %3;(1,0,0) PCI Device NVIDIA GeForce 8800M GTX [NoDB] BIOS String Version 62.92.34.0.8 Installed Drivers nvd3dum (8.16.11.8681), nvwgf2um, nvwgf2um Hard Dik Drive: Model ID ST9120823ASG (**older one 120gb**) Model ID WD32000BEKT (new 320gb with fresh OS)

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

• Unknown problem causing major computer failure, Booting problem with windows 7, mainly with 0x0000000A

  - by ken

  Where do I begin? OS=Windows 7 I think it all started when I ran an installation file. I suspect it may have been a virus (even though AVG scan didnt pick anything up). The installation failed, computer crashed then restarted. In the middle of the reboot, I get BSOD. Normal boot up doesnt work so I use safe mode. Method 1: Not a problem I thought cos I will do what I normally do and that was to recover from my image file. Unfortunately, my Acronis software cant recover in safe mode. Method 2: I created a bootable disc for the Acronis recovery software. Managed to boot to Acronis and started the recovery from image file. This fail with some error message (did not manage to record). Something to do with not be able to copy to $AVG folder. Method 3: At this stage, assumed it was still a virus causing the problem so decided to format that partition to remove everything and hopefully the virus too. Had a lot of problems trying to bypass the system to allow me to format but (i think- more on this later) I managed to do that. Image was recovered, thought problem was resolved. Tried to boot windows but new error: Boot Manager is missing. Read up on this and managed to copy the Boot Manager from my Laptop's Manufacturer's partition (partition contains factory setup image file). Windows loaded but new BSOD with 0x000000A problem. Method 4: Attempted to reinstall factory settings but this failed cos i suspect by formating the partition, I may have removed the recovery software. Tried to create a bootable dvd of factory setting but machine is so bad it continues to crash. Bootable dvd method failed. Method 5:Spent alot of time reading up on this error, even installed a software to help scan and fix the problem. Scan failed and software required money! Anyway, lots of BSOD with different error message like 0x00000001A and 0x0000000D1. Error message changes with some reboots. Method 6: Found a hotfix from the windows site to fix 0x0000000A problem, great I thought! In safe mode, I cant install the file cos of error:0x8007043c. Tried to then install the fix in normal mode but installation just hangs. Returned to safe mode and followed advice to bypass 0x8007043c by changing the BITS status (read here: http://www.vistaheads.com/forums/microsoft-public-windowsupdate/181931-error-number-0x8007043c-windows-update.html). However, my machine at this time is so flaky that it hangs everytime i right mouse click the computer icon. I am at my wits end. Ya help or ideas? Cheers

  Read the article

• Why won't my Windows 8 Command line update its path

  - by mawcsco

  I needed to add a new entry to my PATH variable. This is a common activity for me in my job, but I've recently started using Windows 8. I assumed the process would be similar to Windows 7, Vista, XP... Here's my sequence of events: Open System properties (Start- [type "Control Panel"] - Control Panel\System and Security\System - Advanced system settings - Environment Variables) Add the new path to beginning of my USER PATH variable (C:\dev\Java\apache-ant-1.8.4\bin;) Opened a command prompt (Start - [type "command prompt" enter] - [type "path" enter] My new path entry is not available (see attached image and vide). I Duplicated the exact same process on a Windows 7 machine and it worked. EDIT Windows 8 Environment Variables and Command Prompt video EDIT This is definitely not the behavior of Windows 7. Watch this video to see the behavior I expect working in Windows 7. http://youtu.be/95JXY5X0fII EDIT 5/31/2013 So, after much frustration, I wrote a small C# app to test the WM_SETTINGCHANGE event. This code receives the event in both Windows 7 and Windows 8. However, in Windows 8 on my system, I do not get the correct path; but, I do in Windows 7. This could not be reproduced in other Windows 8 systems. Here is the C# code. using System; using Microsoft.Win32; public sealed class App { static void Main() { SystemEvents.UserPreferenceChanging += new UserPreferenceChangingEventHandler(OnUserPreferenceChanging); Console.WriteLine("Waiting for system events."); Console.WriteLine("Press <Enter> to exit."); Console.ReadLine(); } static void OnUserPreferenceChanging(object sender, UserPreferenceChangingEventArgs e) { Console.WriteLine("The user preference is changing. Category={0}", e.Category); Console.WriteLine("path={0}", System.Environment.GetEnvironmentVariable("PATH")); } } OnUserPreferenceChanging is equivalent to WM_SETTINGCHANGE C# program running in Windows 7 (you can see the event come through and it picks up the correct path). C# program running in Windows 8 (you can see the event come through, but the wrong path). There is something about my environment that is precipitating this problem. However, is this a Windows 8 bug?

  Read the article

• Computer suddenly dies; screen displays weird flickering lines, then restarts

  - by Imray

  I've been having this terrible problem for a little while and just managed to get a picture of 'dead screen' for the first time and I am posting it to seek help. Randomly, at irregular intervals (typically once a week), while working on something (it's been different things every time) my computer will just suddenly go dead - the screen turns to exactly the picture below (the lines flicker a little bit), it hangs there for a few seconds and then restarts. Obviously this is extremely frustrating and I want to try to stop it. I've searched numerous postings with similar keywords but nothing exactly the same as mine. Does anyone have any idea what might be the cause of this? I would post all my system settings and installed programs but the list is long and I don't know how much relevance each item would be. If you'd like to know something specific, please comment and I'll let you know whatever you need. SPECS C:\Users\Imray>systeminfo Host Name: Imray OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Workstation OS Build Type: Multiprocessor Free Registered Owner: Imray - Owner Registered Organization: Product ID: 00371-152-9333854-85895 Original Install Date: 06/09/1999, 5:45:21 PM System Boot Time: 22/03/2013, 8:58:18 AM System Manufacturer: Gateway System Model: DX4840 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 37 Stepping 2 GenuineIntel ~3201 Mhz BIOS Version: American Megatrends Inc. P01-A3 , 17/05/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume2 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 6,135 MB Available Physical Memory: 3,632 MB Virtual Memory: Max Size: 12,268 MB Virtual Memory: Available: 8,114 MB Virtual Memory: In Use: 4,154 MB Page File Location(s): C:\pagefile.sys Domain: WORKGROUP Logon Server: \\Imray-OWNER Hotfix(s): 4 Hotfix(s) Installed. [01]: KB971033 [02]: KB958559 [03]: KB977206 [04]: KB981889 Network Card(s): 2 NIC(s) Installed. [01]: 802.11n Wireless PCI Express Card LAN Adapter Connection Name: Wireless Network Connection DHCP Enabled: Yes DHCP Server: 192.168.2.1 IP address(es) [01]: 192.168.2.13 [02]: fe80::1df1:5399:6890:91f6 [02]: Microsoft Virtual WiFi Miniport Adapter Connection Name: Wireless Network Connection 2 DHCP Enabled: Yes DHCP Server: N/A IP address(es) Graphics Card Specs Name ATI Radeon HD 5570 PNP Device ID PCI\VEN_1002&DEV_68D9&SUBSYS_E142174B&REV_00\4&18A4B35E&0&0008 Adapter Type ATI display adapter (0x68D9), ATI Technologies Inc. compatible Adapter Description ATI Radeon HD 5570 Adapter RAM 1.00 GB (1,073,741,824 bytes) Installed Drivers atiu9p64 aticfx64 aticfx64 atiu9pag aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64 Driver Version 8.700.0.0 INF File oem1.inf (ati2mtag_Evergreen section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1920 x 1080 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xDFFFFFFF Memory Address 0xFBDE0000-0xFBDFFFFF I/O Port 0x0000D000-0x0000DFFF IRQ Channel IRQ 4294967293 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\atikmpag.sys (8.14.1.6095, 181.00 KB (185,344 bytes), 06/09/1999 5:59 PM)

  Read the article

• A proper way to create non-interactive accounts?

  - by AndreyT

  In order to use password-protected file sharing in a basic home network I want to create a number of non-interactive user accounts on a Windows 8 Pro machine in addition to the existing set of interactive accounts. The users that corresponds to those extra accounts will not use this machine interactively, so I don't want their accounts to be available for logon and I don't want their names to appear on welcome screen. In older versions of Windows Pro (up to Windows 7) I did this by first creating the accounts as members of "Users" group, and then including them into "Deny logon locally" list in Local Security Policy settings. This always had the desired effect. However, my question is whether this is the right/best way to do it. The reason I'm asking is that even though this method works in Windows 8 Pro as well, it has one little quirk: interactive users from "User" group are still able to see these extra user names when they go to the Metro screen and hit their own user name in the top-right corner (i.e. open "Sign out/Lock" menu). The command list that drops out contains "Sign out" and "Lock" commands as well as the names of other users (for "switch user" functionality). For some reason that list includes the extra users from "Deny logon locally" list. It is interesting to note that this happens when the current user belongs to "Users" group, but it does not happen when the current user is from "Administrators". For example, let's say I have three accounts on the machine: "Administrator" (from "Administrators", can logon locally), "A" (from "Users", can logon locally), "B" (from "Users", denied logon locally). When "Administrator" is logged in, he can only see user "A" listed in his Metro "Sign out/Lock" menu, i.e. all works as it should. But when user "A" is logged in, he can see both "Administrator" and user "B" in his "Sign out/Lock" menu. Expectedly, in the above example trying to switch from user "A" to user "B" by hitting "B" in the menu does not work: Windows jumps to welcome screen that lists only "Administrator" and "A". Anyway, on the surface this appears to be an interface-level bug in Windows 8. However, I'm wondering if going through "Deny logon locally" setting is the right way to do it in Windows 8. Is there any other way to create a hidden non-interactive user account?

  Read the article

• What are the most likely bottlenecks determining the performance of CamStudio screen recording?

  - by Steve314

  When doing screen recording, I can get a frame rate of maybe 15 frames per second for the full screen on my 1080p monitor using the XVID codec. I can increase the speed a bit by recording a region, changing screen modes, and tweaking other settings, but I'm curious what hardware upgrades might give me the biggest bang for my buck. My PC is budget, but modern... Athlon 2 X4 645 (3.1GHz, quad core, limited cache) processor. 4GB single channel DDR3 1066 RAM. ASRock motherboard with NVidia GeForce 7025/nForce 630a Chipset. ATI Radeon HD 5450 graphics card - 512MB on board, not configured to steal system RAM. I dual-boot Windows XP and Windows 7. For the moment, XP is my bigger performance concern as it's still my getting-things-done O/S as opposed to my browser-host O/S. My goal is to make a few programming-related tutorials. For a lot of that I don't need screen recording - I can make up some slides, record audio with the PC switched off, yada yada. When I do need screen recording, I'll mostly be recording Notepad++, Visual Studio or a command prompt. Occasionally, I may be recording some kind of graphics or diagram program and using my pre-Bamboo cheap Wacom tablet - I have the CS2 versions of Photoshop and Illustrator, but I'd much more likely be using Microsoft Paint. Basically, what I'll be recording won't be making huge demands on the machine - but recording a fair number of pixels (720p preferred) will be useful. What's particularly wierd - not so long ago I still had a five-year-old Pentium 4 based PC. And (with the same 1080p monitor) it could record at not far from the same frame rate. So clearly the performance issues are more subtle than just throw-money-at-it. My first guess would be that the main bottleneck is the bandwidth for transferring data to/from the graphics card. Is that likely to be correct? In support of that, see this [Radeon HD 5450 review][1] - the memory bandwidth is only 12.8 GB/s. If you can't get data out of graphics memory quickly, you can't transfer it back to the system memory quickly. Apparently, that's slower than some top-end cards in 2002.

  Read the article

• Can't find windows 2000 domain after PDC Change

  - by Mark A Kruger

  This is a windows 2000 domain issue. I had an old win2000 PDC that was beginning to fail. So, trying to be pre-emptive, I installed a new BDC, then "demoted" the old PDC and took it off the network. Now it appears that no member server can "find" the domain anymore. No logins work (for services or a RDP or anything). What I've tried (based on googling): Verified sysvol is shared on all servers. Used nslookup to verify that DC's are being found. netdiag /fix meta data cleanup routines. verified no firewall issues (port 389 etc) seizing all roles to new PDC (I did that as part of the original promotion). LMHOST file and Netbios settings. At the moment it seems like I can get the DC's returned but cannot contact them. I'm at a loss. My latest attempt was to remove a member server from the domain and try to "re-add" it. When I do that I get this message: The query was for the SRV record for _ldap._tcp.dc._msdcs.cfwebtools.com The following domain controllers were identified by the query: db-dev1.cfwebtools.com file-prod1.cfwebtools.com cfwt-pdc2.cfwebtools.com However no domain controllers could be contacted. It then goes on to ask if I've checked my A record and made sure they are running. Is there a way to force this domain to be seen? I also shared sysvol (or double checked it) and restarted the dfsr service. More information. I got looking at sysvol and found it was not shared on 2 of these servers. Only one of them (db-dev1) has a "good" or at least "populated" sys vol store. So I tried doing a "d2" recovery of my PDC against that good sysvol. But it never synchs - or at least it does not seem to synch. I'm guessing if I could get sysvol and netlogin to kick in and replicate that would fix my issue. I think these DC's aren't responding because they are waiting for replication which is broken somehow. Would taking down all the DC's except for db-dev1 fix the issue - at least temporarily? I know I can't just copy the sysvol stuff over to the other 2 can I?

  Read the article

• How to make Windows 7 use the internet connection that I specify

  - by user138957

  I have a LAN adapter and a USB wireless internet connection. When both connected windows 7 always uses the USB. I tried changing the metric values but no luck. Let me explains the steps I took. Currently automatic metric on all adapters. LAN connected. ipconfig shows that it is connected to the correct ip/dns/gateway etc. IPv4 Route table shows Metric 24 Then connected USB. ipconfig shows USB connectivity then LAN in that order. Internet is now through USB. IPv4 Route table shows Metric 4249 for LAN and USB is 41. Gateway for USB shows "on-link". netstat -rn shows USBDEVICE on top. Changed LAN metric to 5 and now the route table shows LAN as 9 (not sure why it added 4) and USB as 41. netstat shows LAN then USB. ipconfig shows LAN then USB. But still connection is through USB. How do I know? Task manager shows utilization only through USB as well as speed is showing around 1mbps rather than LANs 10mbps. How can I get win7 use LAN while USB is connected. I am just trying to use USB as a backup just in case I lose LAN connection. Please help!! I thought i will make USB metric manually to say 10. But it says I have to reconnect for it to be effective. Currently USB still shows below LAN and still has 9 and 41 in the table. Disconnected USB. Table shows LAN metric as 24 (Not sure why it got changed from 9 and setting got reverted by to automatic) Reconnected USB. Now in the setting still shows 10 and the route table shows 11 for USB and LAN shows 4249 (settings shows 4245, 4 less)) For some reason restarting USB is resetting LAN setting when reconnected. Thanks

  Read the article

• Wifi randomly drops on Windows 8 laptop

  - by JosiahS

  First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

  Read the article

• Dlink search is hijacking my browser

  - by James

  For months now "DLink search" has been hijacking my search engines. I use google chrome, and I have organized my search engines in the handy dandy "manage search engines" tool about a TRILLION times. It never even says D-link is hacking my search engines. It does not show up! I have read many posts on this forum and others saying that to fix this problem from internet explorer: Setup, internet options, yadayada, magical fairies, and you are solved, but my browser is google chrome! How am I supposed to do this from there! I do not know how to re-setup my Dlink router, which is the cause of the problem! HOW? In those posts with the magical fairies fixing it, HUNDREDS responded saying, "yep, those fairies definitely fixed it right. :)" These people were so satisfied. IT WORKED FOR THEM, WHY NOT ME. I look at it and go ":(" because it does not help me. There are no options for anything to do with this in GOOGLE chrome. PLEASE EXPLAIN and HELP. I see no "SETUP" option, no "Internet Options" button, no anything. BTW the exact posts are these: "Uncheck Advanced DNS in the router internet setup. This will take care of it. I had this problem with my DLink router before." "I had this issue with my DIR-655 and unchecking the Advanced DNS setting in Setup - Internet - Manual Internet Connection Setup fixed it." "If this is just internet explorer, you can go to Tools Internet Options or Internet Options in Control Panel. From here, go to the advanced tab and click the Reset button." "I would set the router's DNS to a site like OpenDNS, and I would ensure the machines are set to get their DNS settings via DHCP or set the machine's DNS setting to OpenDNS. If the router's DNS looks like it was messed with, some bad software know the default passwords for routers and could have changed it. If you don't already I would make sure the password to the router is not default or easy to guess. I've had spyware change a machine's DNS, but the fact it is happening on all machines makes me wonder if it is the router." "Something got into your router and changed the dns server most likely, do a hard reset of the router and then change the password to something strong. Also check for a firmware update for the router and apply it as soon as possible."

  Read the article

• Can I use one virtualbox disk for multiple machines?

  - by mxp

  I'm not sure what search term to use and skimming through the VirtualBox manual didn't help me either, so I ask my two questions here... My setup is this: PC with dual boot into Windows 7 and a Debian operating system (both 64bit). I've created a virtual machine (Kubuntu, 64bit) under Windows and put it's VDI file on a SMB share of my NAS. Then I created a VM under linux using the same settings for memory etc and assigned the existing VDI file to it. My idea was that I could use that virtual machine from Windows and Linux as well. (1) Is this generally something that should work without problems? I noticed that snapshots get me into trouble because they appear to be not visible from the other operating system: The snapshots I took after installing the guest system are not visible under Linux. That's why I shut down the VM after usage and not save its state while it's running. My current problem is this: I have used the VM under Windows first, then under Linux. Now it will only start on Linux. When trying this on Windows the guest OS detects some kind of hard disk error and fails to boot because it cannot mount its drive. Obviously the virtual hard disk won't fail so it must have something to do with me using it under Linux. (2) How can I fix that? Update: It also looks like any changes I made in the VM under Linux have been reset by trying to boot it under Windows. Looks like it's back to the latest snapshot. I'm confused... Update The answer to my first question can be found below. In short: It works, as long as you don't use snapshots. The answer to my second question is this: Under Windows set the VM back to the latest snapshot and then discard the snapshot so it gets merged. There should be no snapshots left at the end. If you have multiple snapshots, discard the earliest ones first (Snapshot 1, then 2, 3, ...). I'm not sure what happens if you start at the end (.., 3, 2, 1). This of course leads to some data loss since you revert all changes since the last snapshot. But at least the VM is usable again.

  Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >