Search Results

Search found 16809 results on 673 pages for 'nothing 2 lose'.

Page 463/673 | < Previous Page | 459 460 461 462 463 464 465 466 467 468 469 470  | Next Page >

• Sparc v440 unable 2 boot after recommended patch install

  - by user100660

  After installing the October 2011 recommended patch bundle on a Solaris 10 the host fails to boot. The output is {0} ok boot SC Alert: Host System has Reset screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. Sun Fire V440, No Keyboard Copyright 1998-2003 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.10.10, 8192 MB memory installed, Serial #54744555. Ethernet address 0:3:ba:43:55:eb, Host ID: 834355eb. Rebooting with command: boot Boot device: /pci@1f,700000/scsi@2/disk@0,0:a File and args: \ Evaluating: Out of memory Warning: Fcode sequence resulted in a net stack depth change of 1 Evaluating: Evaluating: The file just loaded does not appear to be executable. {3} ok If I do a boot -F failsafe the host come up and I'm able to mount the root device (ufs on /dev/dsk/c1t0d0s0) and nothing appears broken, i.e I can see the logfiles from the patch install etc. Root device still have 1GB+ free. Only 2 kernel patches was installed from the patch bundle: 144500-19 & 147440-02. Any hints how to debug it further, etc.

  Read the article

• Ubuntu Postfix Gmail SMTP Relay Not Working

  - by Nick DeMayo

  I currently have postfix set up to relay messages from my websites through gmail, and up until recently it was working perfectly. However, within the last week or so (not really sure when) I started getting the below error whenever attempting to send an email: Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[2001:4860:800a::6c]:587: Network is unreachable Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[173.194.76.109]:587: Connection refused Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[173.194.76.108]:587: Connection refused Here is my configuration file: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h #readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = [my domain name] alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases #myorigin = /etc/mailname mydestination = [my host name], localhost.localdomain, localhost relayhost = [smtp.gmail.com]:587 mynetworks = 127.0.0.0/8 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = loopback-only inet_protocols = all ########################################## ##### non debconf entries start here ##### ##### client TLS parameters ##### smtp_tls_loglevel=1 smtp_tls_security_level=encrypt smtp_sasl_auth_enable=yes smtp_sasl_password_maps=hash:/etc/postfix/sasl/passwd smtp_sasl_security_options = noanonymous ##### map username@localhost to [email protected] ##### smtp_generic_maps=hash:/etc/postfix/generic Nothing changed on my server, as far as I know...any ideas what could have caused it to stop working?

  Read the article

• pure-ftpd not listening on specified port

  - by Jason McLaren

  I installed the pure-ftpd package (version 1.0.35-1) on an Ubuntu 12.04 box (an EC2 instance based on the standard Ubuntu 12.04 AMI). The pure-ftpd daemon is running (verified with ps), though there is no PID file (expected one to be created by the /etc/init.d/pure-ftpd script). Here's the resulting command that gets run by the init.d script: /usr/sbin/pure-ftpd -l pam -O clf:/var/log/pure-ftpd/transfer.log -o -8 UTF-8 -u 1000 -E -B -g /var/run/pure-ftpd/pure-ftpd.pid Here's my real problem: the ftp server isn't actually listening on any port (checked with netstat and nmap). So I can't ftp to the server (either locally using localhost or remotely using the public IP address). I tried adding a Bind file to /etc/pure-ftpd/conf and restarting, but it didn't help. When I installed pure-ftpd, it replaced inetd with openbsd-inetd, but did not run it since there were no services enabled. So inetd is not listening on port 21 either. (Apparently Ubuntu has a no-inetd-by-default policy, according to https://lists.ubuntu.com/archives/ubuntu-users/2010-September/227905.html .) I want to run pure-ftpd by itself (not with inetd) anyways, since the /etc/init.d/pure-ftpd script requires no inetd if you use the UploadScript feature. I'm not familiar with how Ubuntu handles network services (and can't find any relevant docs besides generic man pages), so I'm probably missing something obvious. Nothing seems out of the ordinary with /etc/hosts.allow (empty) or hosts.deny (empty), and I didn't add any firewall rules (iptables -L shows that the firewall is in its initial state). I've checked the pure-ftpd docs; not sure what else to look at. Any help would be appreciated, thanks!

  Read the article

• Apache2 will not start on OpenSUSE after enabling mod_pagespeed

  - by alpha1

  I have a linode VPS, running openSUSE 12.1 (A little outdated, but stable). I have installed the RPMS for mod_pagespeed. mod_pagespeed.conf has "ModPagespeed on". Restarting apache fails after enabling pagespeed. the errors are not very helpful. li361-39:/usr/lib64/apache2 # a2enmod pagespeed li361-39:/usr/lib64/apache2 # service apache2 restart redirecting to systemctl Job failed. See system logs and 'systemctl status' for details. li361-39:/usr/lib64/apache2 # systemctl status apache2.service apache2.service - apache Loaded: loaded (/lib/systemd/system/apache2.service; enabled) Active: failed since Thu, 06 Jun 2013 20:49:00 +0000; 1s ago Process: 6701 ExecStop=/usr/sbin/httpd2 -D SYSTEMD -k stop (code=exited, status=0/SUCCESS) Process: 6704 ExecStart=/usr/sbin/start_apache2 -D SYSTEMD -k start (code=exited, status=1/FAILURE) Main PID: 6637 (code=exited, status=0/SUCCESS) CGroup: name=systemd:/system/apache2.service li361-39:/usr/lib64/apache2 # a2dismod pagespeed li361-39:/usr/lib64/apache2 # service apache2 restart redirecting to systemctl li361-39:/usr/lib64/apache2 # And the error log (/var/log/apache2/error_log) is useless as well. [Thu Jun 06 20:48:59 2013] [notice] caught SIGTERM, shutting down [Thu Jun 06 20:49:12 2013] [warn] Init: Session Cache is not configured [hint: SSLSessionCache] [Thu Jun 06 20:49:13 2013] [notice] Apache/2.2.21 (Linux/SUSE) mod_ssl/2.2.21 OpenSSL/1.0.0k PHP/5.4.15 configured -- resuming normal operations EDIT This is from /var/log/messages Jun 12 14:24:14 li361-39 start_apache2[27951]: httpd2-prefork: Syntax error on line 116 of /etc/apache2/httpd.conf: Syntax error on line 34 of /etc/apache2/sysconfig.d/loadmodule.conf: Cannot load /usr/lib64/apache2/mod_pagespeed.so into server: /usr/lib64/apache2/mod_pagespeed.so: undefined symbol: ap_unixd_config Full Log is here: http://pastebin.com/hjnbZZTr I've tried looking for other logs and checking the mod_pagespeed.conf against posts claiming it works and nothing is striking as wrong. Any Ideas?

  Read the article

• ASUS P8B WS - Endless Reboots

  - by tuxGurl

  I am running a Intel XEON 1245 with 4GBx2 Kingston Memory ECC Unbuffered DDR3 on an ASUS P8B WS motherboard. BIOS Version 0904 x64. This system is a little over a month old. It is running Ubuntu 11.10. This evening I found the machine turned off. When I tried to restart it, it would POST and stop at the GRUB screen. When I selected Ubuntu and hit enter within 2-3 seconds the would shutdown and restart. If I stayed at the GRUB screen and did nothing the system would not cut out. I tried booting off a USB stick and again 2-3 seconds after selecting 'Try Ubuntu without Installing' the machine will cut power and reboot. Things I have tried so far: Resetting the BIOS using the on board jumper Resetting the BIOS settings to default Disconnecting all external hardware - except keyboard & monitor Booting with 1 stick of RAM - I tried different single sticks Ensured that onboard EPU and GPU boost switches are in the off position. I am running a Memtest86 right now and it has been running for 38+ minutes. This is not an OS problem or an overheating issue (I have a CoolerMaster HAF Case with 3 fans besides the CPU fan) I am at a loss as to what to try next. I think the BIOS is mis-configured somehow but I don't know what to look for.

  Read the article

• OCZ Vertex 3 SSD boot failure

  - by Col Zero

  Ok, so I just purchased and received a 120GB OCZ Vertex 3. I had Windows 7 on an .ISO file on my computer. I formatted a USB stick and configured it to be read as a CD so that I could install windows onto my SSD from it. I started my comp, had the boot priority set to my USB, starting installing windows 7 to my SSD. And out of no where (I wasn't watching) my computer restarted and it brought me back to the beginning of the Windows 7 set-up. So I turned my computer off and booted it up from the SSD to see if it had installed onto the SSD. The first 2 attempts I had a disk boot failure. So I plugged my hard drive back in, started my computer, turned it off, plugged the SSD back in (literally) and it booted up fine/ Finalized windows got internet set up, and Windows had updates that required a restart. So I restarted and had another disk boot failure. Now I have a disk boot failure every time I try to start my computer up through my SSD. Extra Info: My SSD has never been able to be detected in my BIOS unless my Hard Drive was unplugged (eve then my BIOS didn't always detect it). MY SSD wasn't detected in my BIOS the first and only time it successfully booted up. My SSD literally boots up successfully randomly (only once unfortunately) and is detected in my BIOS randomly. I've tried switching cords etc and nothing has worked. I just want to get this damn thing running so I can see whats its like. I finally found a way to get the OS on this sucker and now it won't even boot up. Any help appreciated

  Read the article

• Can't successfully run Sharepoint Foundation 2010 first time configuration

  - by Robert Koritnik

  I'm trying to run the non-GUI version of configuration wizard using power shell because I would like to set config and admin database names. GUI wizard doesn't give you all possible options for configuration (but even though it doesn't do it either). I run this command: New-SPConfigurationDatabase -DatabaseName "Sharepoint2010Config" -DatabaseServer "developer.mydomain.pri" -AdministrationContentDatabaseName "Sharepoint2010Admin" -DatabaseCredentials (Get-Credential) -Passphrase (ConvertTo-SecureString "%h4r3p0int" -AsPlainText -Force) Of course all these are in the same line. I've broken them down into separate lines to make it easier to read. When I run this command I get this error: New-SPConfigurationDatabase : Cannot connect to database master at SQL server a t developer.mydomain.pri. The database might not exist, or the current user does not have permission to connect to it. At line:1 char:28 + New-SPConfigurationDatabase <<<< -DatabaseName "Sharepoint2010Config" -Datab aseServer "developer.mydomain.pri" -AdministrationContentDatabaseName "Sharepoint 2010Admin" -DatabaseCredentials (Get-Credential) -Passphrase (ConvertTo-SecureS tring "%h4r3p0int" -AsPlainText -Force) + CategoryInfo : InvalidData: (Microsoft.Share...urationDatabase: SPCmdletNewSPConfigurationDatabase) [New-SPConfigurationDatabase], SPExcep tion + FullyQualifiedErrorId : Microsoft.SharePoint.PowerShell.SPCmdletNewSPCon figurationDatabase I created two domain accounts and haven't added them to any group: SPF_DATABASE - database account SPF_ADMIN - farm account I'm running powershell console as domain administrator. I've tried to run SQL Management studio as domain admin and created a dummy database and it worked without a problem. I'm running: Windows 7 x64 on the machine where Sharepoint Foundation 2010 should be installed and also has preinstalled SQL Server 2008 R2 database Windows Server 2008 R2 Server Core is my domain controller that just serves domain features and nothing else I've installed Sharepoint according to MS guides http://msdn.microsoft.com/en-us/library/ee554869%28office.14%29.aspx installing all additional patches that are related to my configuration. Any ideas what should I do to make it work?

  Read the article

• Create new folder for new sender name and move message into new folder

  - by Dave Jarvis

  Background I'd like to have Outlook 2010 automatically move e-mails into folders designated by the person's name. For example: Click Rules Click Manage Rules & Alerts Click New Rule Select "Move messages from someone to a folder" Click Next The following dialog is shown: Problem The next part usually looks as follows: Click people or public group Select the desired person Click specified Select the desired folder Question How would you automate those problematic manual tasks? Here's the logic for the new rule I'd like to create: Receive a new message. Extract the name of the sender. If it does not exist, create a new folder under Inbox Move the new message into the folder assigned to that person's name I think this will require a VBA macro. Related Links http://www.experts-exchange.com/Software/Office_Productivity/Groupware/Outlook/A_420-Extending-Outlook-Rules-via-Scripting.html http://msdn.microsoft.com/en-us/library/office/ee814735.aspx http://msdn.microsoft.com/en-us/library/office/ee814736.aspx http://stackoverflow.com/questions/11263483/how-do-i-trigger-a-macro-to-run-after-a-new-mail-is-received-in-outlook http://en.kioskea.net/faq/6174-outlook-a-macro-to-create-folders http://blogs.iis.net/robert_mcmurray/archive/2010/02/25/outlook-macros-part-1-moving-emails-into-personal-folders.aspx Update #1 The code might resemble something like: Public WithEvents myOlApp As Outlook.Application Sub Initialize_handler() Set myOlApp = CreateObject("Outlook.Application") End Sub Private Sub myOlApp_NewMail() Dim myInbox As Outlook.MAPIFolder Dim myItem As Outlook.MailItem Set myInbox = myOlApp.GetNamespace("MAPI").GetDefaultFolder(olFolderInbox) Set mySenderName = myItem.SenderName On Error GoTo ErrorHandler Set myDestinationFolder = myInbox.Folders.Add(mySenderName, olFolderInbox) Set myItems = myInbox.Items Set myItem = myItems.Find("[SenderName] = " & mySenderName) myItem.Move myDestinationFolder ErrorHandler: Resume Next End Sub Update #2 Split the code as follows: Sent a test message and nothing happened. The instructions for actually triggering a message when a new message arrives are a little light on details (for example, no mention is made regarding ThisOutlookSession and how to use it). Thank you.

  Read the article

• Nexus 1000v VEM fails on 2 out of 8 hosts.

  - by cougar694u

  I have 8 ESXi hosts. I do a fresh install from the installable CD directly to 4u1. We have another 2-node cluster with a working Nexus 1000v primary & secondary. Everything's up and running. I installed 6 hosts and everything worked great, migrated them to the Nexus DVS, and VUM installed the modules. I did the 7th host, and when I tried to migrate it to the DVS, it failed with the following error: Cannot complete a Distributed Virtual Switch operation for one or more host memebers. DVS Operation failed on host , error durring the configuration of the host: create dvswitch failed with the following error message: SysinfoException: Node (VSI_NODE_net_create) ; Status(bad0003)= Not found ; Message = Instance(0): Inpute(3) DvsPortset-0 256 cisco_nexus_1000v got (vim.fault.PlatformConfigFault) exception Then, I tried to do host 8, and got the exact same problem. It worked about 15 minutes prior when I did host 6, nothing changed, then went to host 7 and it failed. If I try to remediate either of these two hosts, either patches or extensions, it fails. Anyone else have these problems?

  Read the article

• WHS - Windows Update Failure

  - by Kyle B.

  Clicking "Update Now..." inside my EX470 control panel for Windows Update produces the following error message: "Windows Home Server updates installation can not complete. Please try again later. If the problem persists, please restart the server." I have rebooted the server numerous times, and I have also used remote desktop to connect to the machine to perform the update this way, however the browser is unable to pull up http://windowsupdate.microsoft.com. This is very strange behavior because I am able to access all other sites (gmail.com, serverfault.com, etc). Would it be possible for someone to explain to me how I can check to see what is blocking the connection of this device, which apparently has a valid internet connection, to the Microsoft Windows Update site? note #1 Using the shortcut: %SystemRoot%\system32\wupdmgr.exe does not work either. It says "Connecting to 65.55.200.155..." but nothing ever happens. This is strange because all other sites seem fine. Also, I can connect to windowsupdate.microsoft.com on my local desktop so I know this is running as well

  Read the article

• Resize Debian in VirtualBox

  - by Poni

  I have a VM with one HD of size 3GB and I'd like to enlarge its HD to 7GB. So I execute this command on the host (while guest is shutdown): VBoxManage modifyhd debian.vdi --resize 7168 Then I run the guest, Debian 6, and then: smith@debian6:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda1 2.8G 2.6G 60M 98% / tmpfs 61M 0 61M 0% /lib/init/rw udev 57M 160K 57M 1% /dev tmpfs 61M 0 61M 0% /dev/shm smith@debian6:~$ sudo parted /dev/sda print Model: ATA VBOX HARDDISK (scsi) Disk /dev/sda: 3221MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 3035MB 3034MB primary ext3 boot 2 3036MB 3220MB 185MB extended 5 3036MB 3220MB 185MB logical linux-swap(v1) smith@debian6:~$ cat /proc/partitions major minor #blocks name 8 0 3145728 sda 8 1 2962432 sda1 8 2 1 sda2 8 5 180224 sda5 So, no automatic resizing (detection) of the HD/partition (while VirtualBox, in the host, shows it's 7GB now). Ok... Then I do: smith@debian6:~$ sudo resize2fs /dev/sda1 resize2fs 1.41.12 (17-May-2010) The filesystem is already 740608 blocks long. Nothing to do! smith@debian6:~$ sudo parted GNU Parted 2.3 Using /dev/sda Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) select /dev/sda1 Using /dev/sda1 (parted) resize WARNING: you are attempting to use parted to operate on (resize) a file system. parted's file system manipulation code is not as robust as what you'll find in dedicated, file-system-specific packages like e2fsprogs. We recommend you use parted only to manipulate partition tables, whenever possible. Support for performing most operations on most types of file systems will be removed in an upcoming release. Partition number? 1 Start? 0 End? [3034MB]? Here I'm stuck. At the above parted it asks me to resize to 3GB. No point in that, right.. What should I do in order to enlarge this partition?

  Read the article

• Unable to boot with Windows 2008 DVD / USB Key

  - by r0ca

  Hi everyone, I am trying to install Windows 2008 server on a HP Proliant DL180 G5. There is no built-in DVD reader so I need to use my LaCie USB one. When I put the CD in and boot from the USB DVD on the server, I get the error message: Boot Failed! Please insert boot media in selected boot device. So I tried with another Windows bootable CD and still no luck. What I've done then, I copied the installation DVD on my 16go USB key. Again, impossible to boot from the USB Key. I have 2 147go SAS 15k HDD on my server. They are not showing in the Bios. I was wondering if this is a reason why nothing will boot on it. I am trying to find a way to deploy Windows 2008 server on my HP server as soon as possible. If you guys have ideas, feel free to let me know :) Best regards, David. System Information: HP Proliant DL180 G5 Quad-Core 2.5 4GO Ram 2x 147GO SAS 15k P.S. This is my first installation ever on SAS/SCSI HDD. Thanks a bunch! Edit: Well, my bad! I purchased a new USB DVD and now I can install Windows 2008 server. Thanks a bunch for your help!

  Read the article

• HP c6180 driver refuses to install - "must reboot to continue delete files and continue install" loo

  - by Aszurom

  User called me last night, can't get HP drivers to install for printer. 500 meg download for latest c6180 driver. PC says "computer must be restarted to delete some files, then setup will continue." and it won't pass that point. (that's not exact phrasing of the error, and I'm not on the system now) Target machine is XP SP2. I upgraded to SP3. Fully patched. Ran malwarebytes, spybot, hijack this and turned off all startup entries. I noted that windows update also failed on optional printer driver updates for other printers installed on the machine. Went to printer server properties, removed all print drivers from system, deleted all printer ports. Made sure no services were marked disabled. After 5 hours of fighting this I started to get desperate, and uninstalled anything that referenced HP in the machine at all. Still no cure. I'm 6 hours into this and completely stumped. Google returns nothing applicable except unanswered requests for help on same topic.

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• External USB attached drive works in Windows XP but not in Windows 7. How to fix?

  - by irrational John

  Earlier this week I purchased this "N52300 EZQuest Pro" external hard drive enclosure from here. I can connect the enclosure using USB 2.0 and access the files in both NTFS partitions on the MBR partitioned drive when I use either Windows XP (SP3) or Mac OS X 10.6. So it works as expected in XP & Snow Leopard. However, the enclosure does not work in Windows 7 (Home Premium) either 64-bit or 32-bit or in Ubuntu 10.04 (kernel 2.6.32-23-generic). I'm thinking this must be a Windows 7 driver problem because the enclosure works in XP & Snow Leopard. I do know that no special drivers are required to use this enclosure. It is supported using the USB mass storage drivers included with XP and OS X. It should also work fine using the mass storage support in Windows 7, no? FWIW, I have also tried using 32-bit Windows 7 on both my desktop, a Gigabyte GA-965P-DS3 with a Pentium Dual-Core E6500 @ 2.93GHz, and on my early 2008 MacBook. I see the same failure in both cases that I see with 64-bit Windows 7. So it doesn't appear to be specific to one hardware platform. I'm hoping someone out there can help me either get the enclosure to work in Windows 7 or convince me that the enclosure hardware is bad and should be RMAed. At the moment though an RMA seems pointless since this appears to be a (Windows 7) device driver problem. I have tried to track down any updates to the mass storage drivers included with Windows 7 but have so far come up empty. Heck, I can't even figure out how to place a bug report with Microsoft since apparently the grace period for Windows 7 email support is only a few months. I came across a link to some USB troubleshooting steps in another question. I haven't had a chance to look over the suggestions on that site or try them yet. Maybe tomorrow if I have time ... ;-) I'll finish up with some more details about the problem. When I connect the enclosure using USB to Windows 7 at first it appears everything worked. Windows detects the drive and installs a driver for it. Looking in Device Manager there is an entry under the Hard Drives section with the title, Hitachi HDT721010SLA360 USB Device. When you open Windows Disk Management the first time after the enclosure has been attached the drive appears as "Not initialize" and I'm prompted to initialize it. This is bogus. After all, the drive worked fine in XP so I know it has already been initialized, partitioned, and formatted. So of course I never try to initialize it "again". (It's a 1 GB drive and I don't want to lose the data on it). Except for this first time, the drive never shows up in Disk Management again unless I uninstall the Hitachi HDT721010SLA360 USB Device entry under Hard Drives, unplug, and then replug the enclosure. If I do that then the process in the previous paragraph repeats. In Ubuntu the enclosure never shows up at all at the file system level. Below are an excerpt from kern.log and an excerpt from the result of lsusb -v after attaching the enclosure. It appears that Ubuntu at first recongnizes the enclosure and is attempting to attach it, but encounters errors which prevent it from doing so. Unfortunately, I don't know whether any of this info is useful or not. excerpt from kern.log [ 2684.240015] usb 1-2: new high speed USB device using ehci_hcd and address 22 [ 2684.393618] usb 1-2: configuration #1 chosen from 1 choice [ 2684.395399] scsi17 : SCSI emulation for USB Mass Storage devices [ 2684.395570] usb-storage: device found at 22 [ 2684.395572] usb-storage: waiting for device to settle before scanning [ 2689.390412] usb-storage: device scan complete [ 2689.390894] scsi 17:0:0:0: Direct-Access Hitachi HDT721010SLA360 ST6O PQ: 0 ANSI: 4 [ 2689.392237] sd 17:0:0:0: Attached scsi generic sg7 type 0 [ 2689.395269] sd 17:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 2689.395632] sd 17:0:0:0: [sde] Write Protect is off [ 2689.395636] sd 17:0:0:0: [sde] Mode Sense: 11 00 00 00 [ 2689.395639] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412003] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412009] sde: sde1 sde2 [ 2689.455759] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.455765] sd 17:0:0:0: [sde] Attached SCSI disk [ 2692.620017] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2707.740014] usb 1-2: device descriptor read/64, error -110 [ 2722.970103] usb 1-2: device descriptor read/64, error -110 [ 2723.200027] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2738.320019] usb 1-2: device descriptor read/64, error -110 [ 2753.550024] usb 1-2: device descriptor read/64, error -110 [ 2753.780020] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2758.810147] usb 1-2: device descriptor read/8, error -110 [ 2763.940142] usb 1-2: device descriptor read/8, error -110 [ 2764.170014] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2769.200141] usb 1-2: device descriptor read/8, error -110 [ 2774.330137] usb 1-2: device descriptor read/8, error -110 [ 2774.440069] usb 1-2: USB disconnect, address 22 [ 2774.440503] sd 17:0:0:0: Device offlined - not ready after error recovery [ 2774.590023] usb 1-2: new high speed USB device using ehci_hcd and address 23 [ 2789.710020] usb 1-2: device descriptor read/64, error -110 [ 2804.940020] usb 1-2: device descriptor read/64, error -110 [ 2805.170026] usb 1-2: new high speed USB device using ehci_hcd and address 24 [ 2820.290019] usb 1-2: device descriptor read/64, error -110 [ 2835.520027] usb 1-2: device descriptor read/64, error -110 [ 2835.750018] usb 1-2: new high speed USB device using ehci_hcd and address 25 [ 2840.780085] usb 1-2: device descriptor read/8, error -110 [ 2845.910079] usb 1-2: device descriptor read/8, error -110 [ 2846.140023] usb 1-2: new high speed USB device using ehci_hcd and address 26 [ 2851.170112] usb 1-2: device descriptor read/8, error -110 [ 2856.300077] usb 1-2: device descriptor read/8, error -110 [ 2856.410027] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 2856.730033] usb 3-2: new full speed USB device using uhci_hcd and address 11 [ 2871.850017] usb 3-2: device descriptor read/64, error -110 [ 2887.080014] usb 3-2: device descriptor read/64, error -110 [ 2887.310011] usb 3-2: new full speed USB device using uhci_hcd and address 12 [ 2902.430021] usb 3-2: device descriptor read/64, error -110 [ 2917.660013] usb 3-2: device descriptor read/64, error -110 [ 2917.890016] usb 3-2: new full speed USB device using uhci_hcd and address 13 [ 2922.911623] usb 3-2: device descriptor read/8, error -110 [ 2928.051753] usb 3-2: device descriptor read/8, error -110 [ 2928.280013] usb 3-2: new full speed USB device using uhci_hcd and address 14 [ 2933.301876] usb 3-2: device descriptor read/8, error -110 [ 2938.431993] usb 3-2: device descriptor read/8, error -110 [ 2938.540073] hub 3-0:1.0: unable to enumerate USB device on port 2 excerpt from lsusb -v Bus 001 Device 017: ID 0dc4:0000 Macpower Peripherals, Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0dc4 Macpower Peripherals, Ltd idProduct 0x0000 bcdDevice 0.01 iManufacturer 1 EZ QUEST iProduct 2 USB Mass Storage iSerial 3 220417 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 5 Config0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 4 Interface0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Update: Results using Firewire to connect. Today I recieved a 1394b 9 pin to 1394a 6 pin cable which allowed me to connect the "EZQuest Pro" via Firewire. Everything works. When I use Firewire I can connect whether I'm using Windows 7 or Ubuntu 10.04. I even tried booting my Gigabyte desktop as an OS X 10.6.3 Hackintosh and it worked there as well. (Though if I recall correctly, it also worked when using USB 2.0 and booting OS X on the desktop. Certainly it works with USB 2.0 and my MacBook.) I believe the firmware on the device is at the latest level available, v1.07. I base this on the excerpt below from the OS X System Profiler which shows Firmware Revision: 0x107. Bottom line: It's nice that the enclosure is actually usable when I connect with Firewire. But I am still searching for an answer as to why it does not work correctly when using USB 2.0 in Windows 7 (and Ubuntu ... but really Windows 7 is my biggest concern). OXFORD IDE Device 1: Manufacturer: EZ QUEST Model: 0x0 GUID: 0x1D202E0220417 Maximum Speed: Up to 800 Mb/sec Connection Speed: Up to 400 Mb/sec Sub-units: OXFORD IDE Device 1 Unit: Unit Software Version: 0x10483 Unit Spec ID: 0x609E Firmware Revision: 0x107 Product Revision Level: ST6O Sub-units: OXFORD IDE Device 1 SBP-LUN: Capacity: 1 TB (1,000,204,886,016 bytes) Removable Media: Yes BSD Name: disk3 Partition Map Type: MBR (Master Boot Record) S.M.A.R.T. status: Not Supported

  Read the article

• Recommendations for secure business collaboration tools

  - by Michael Prescott

  I'm searching for a secure and easy way for business partners to collaboratively edit and exchange documents, share calendars, create schedules, and assign tasks. I speculate that the ideal collaboration environment or work-flow would actually involve several technologies and services. My co-workers and I have tried a variety of things from Google Apps to Wiki's, but nothing feels very fluid or complete. I suppose defining what we need and our constraints is probably in order: collaboratively edit basic text documents and spreadsheets exchange documents like flow-charts, graphs, and files generated by our other desktop applications, but not source code assign tasks to each other and ourselves and track the history of those tasks easily see when relevant documents have been modified since last viewing and ability to easily push notifications to relevant workers (a clean front page that shows updates would probably suffice) provide limited access to contract workers and guests users if a remote user system is compromised (keystroke logger or other spyware) we don't want the criminal to be able to gain access to all business documents (processes, trade-secrets, customer lists, etc.) simply because they gained access to a single Google account (or whatever web service) Cannot be a difficult to administer VPN infrastructure Cannot cost more than $100 per month (yeah, money is tight) Needs to support up to 25 users We can host our own web applications, but it must be low maintenance solution

  Read the article

• mysqld causes high CPU load

  - by Radu

  My mysqld goes to use 99.9% of CPU for variable time (between 2 - 20 minutes), and then goes back to normal 0.1% - 5%. Checked processlist: all is normal, 1 to 20 inserts or updates that last 2 to 5 sec, and about 20 process that are in Sleep Mode (maybe because the scripts don't close the mysql connection, but are they are closed in about 5 - 10 secs, I didn't make the scripts :P but the server was running fine the last 2 years, since is was made): | 15375 | root | localhost | stoc | Query | 0 | NULL | show processlist | | 79480 | pppoe | localhost | pppoe | Sleep | 4 | NULL | NULL | | 79481 | pppoe | localhost | pppoe | Sleep | 4 | NULL | NULL | | 79482 | pppoe | localhost | pppoe | Sleep | 4 | NULL | NULL | | 79483 | pppoe | localhost | pppoe | Query | 0 | init | UPDATE acc SET InputOctets="0", OutputOctets="0", InputPackets="unknown", OutputPackets="User | | 79484 | pppoe | localhost | pppoe | Sleep | 5 | NULL | NULL | | 79485 | pppoe | localhost | pppoe | Sleep | 5 | NULL | NULL | | 79486 | pppoe | localhost | pppoe | Sleep | 5 | NULL | NULL Checked raid, seemns OK: [root@db2]# cat /proc/mdstat Personalities : [raid5] [raid4] [raid1] md0 : active raid1 sdd1[3] sdc1[2] sdb1[0] sda1[1] 136448 blocks [4/4] [UUUU] md1 : active raid5 sdd2[3] sdc2[2] sdb2[0] sda2[1] 12023808 blocks level 5, 256k chunk, algorithm 2 [4/4] [UUUU] md3 : active raid5 sda4[1] sdd4[3] sdc4[2] sdb4[0] 203647488 blocks level 5, 256k chunk, algorithm 2 [4/4] [UUUU] md2 : active raid5 sda3[1] sdd3[3] sdc3[2] sdb3[0] 24024576 blocks level 5, 256k chunk, algorithm 2 [4/4] [UUUU] unused devices: <none> [root@db2]# top sees my mysqld cpu load, but nothing else seems to be wrong: [root@db2]# top top - 17:56:05 up 7 days, 3:55, 3 users, load average: 32.93, 24.72, 22.70 Tasks: 75 total, 4 running, 71 sleeping, 0 stopped, 0 zombie Cpu(s): 63.4% us, 36.6% sy, 0.0% ni, 0.0% id, 0.0% wa, 0.0% hi, 0.0% si, 0.0% st Mem: 1988824k total, 1304776k used, 684048k free, 99588k buffers Swap: 12023800k total, 0k used, 12023800k free, 951028k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 5754 mysql 19 0 236m 57m 5108 R 99.9 2.9 21:58.76 mysqld 1 root 16 0 7216 700 580 S 0.0 0.0 0:00.39 init 2 root RT 0 0 0 0 S 0.0 0.0 0:00.00 migration/0 Repaired all mysql databases, reindexed raid ... I'm running out of ideeas ... Anyone has an ideea what can go wrong with this server ? Thank you

  Read the article

• Windows system restore deletes various executables and *.js files. How does it decide which files to delete?

  - by Leftium

  I restored my system from a Windows System Restore point. It solved some issues I was having, but introduced other strange problems (like my optical drive disappeared). One thing that surprised me was several files from my Web2Py installation were deleted: the executables and *.js files; possibly some others (like favicon.ico). I did not expect this because Web2Py is basically a portable, standalone application. You just unzip it and run the executable inside, so nothing should be registered with Windows. My question is: what files does Windows system restore delete, and how does it decide this? I'm just wondering what other files I'm missing and if there's a way to get restore them (without rolling back the restore point). Perhaps it scans for certain files types (like exe, js, ico, dll) with a creation date that was after the restore point creation date? Some other people who experienced a similar problem: Dropbox: Lost Files User files missing after run system restore. update: I found some more references on how Windows System Restore works: Understanding how System Restore in Windows Vista treats executable files Why Vista's System Restore is Dangerous and What to do About it

  Read the article

• Ubuntu 12.4 compiz - disable all compiz plugin - empty screen

  - by gotqn

  A friend of mine has installed on my new machine Ubuntu 10.4 (I have always been windows user and have no experience with Linux). I started to watch some tutorial about how to make 'Rotated Cube' using 'Compiz',but the cube appears in the form of a list (only two slides). I have thought this could be result of my video cards (only two - one from the processor and one from the motherboard) and they can not support this options. Anyway, I have decided to disable all compiz plugins and options because my friend has set some, and I started to think there is some misunderstanding between the plugins. After, that I got only empty screen(no menu, no icons, anything) and can do nothing. How to fix this? EDIT: When I remove the compiz stuffs (from the console), the menu is shown again. Then I install the compiz again (some of the effect are still not working). After restart or log out/in the menu is hidden again. I suppose that there are some settings that I've broken but they are saved somewhere in the system and remove the compiz do not deleted them and as a result they are activated after compiz is installed again and the PC is restarted?

  Read the article

• How to render remote assistance to a person using Live Messenger?

  - by Cheeso

  There is a feature within Windows Live Messenger v9 that allows a person to ask for remote assistance. BBut as I understand it, this works only if the router is UPnP enabled on both ends. Today I tried this with a friend during an active chat session, and nothing happened. I suspect a router problem. as I am remote, I cannot configure the router for them. What's a good way to render remote assistance? Here's the scenario: it will be based on invitation only (it's not a remote desktop or "logmein" situation). It's a younger person, a computer novice, on the other end of the wire. I'll be assiting with their use of applications on the PC. I'd l ike to be able to SEE the screen, and also use the mouse and keyboard. I have used Ultra-Vnc on the target machine and vncviewer on my machine, on a LAN. It works well. But I don't think I can use that, because it's my kids' computer in my ex-wife's place, and I don't want her to accuse me of spying on her computer. That's why I need it to be invitation only. Advice please. Is there an easy way for me to set up Remote Assistance? IS there some other tool I can use?

  Read the article

• Debian amd64 on Dell Studio 540 reboot hangs

  - by Shcheklein

  Hi, I have Dell Studio 540 desktop and Debian Lenny installed on it: 2.6.26-2-amd64 #1 SMP Tue Mar 9 22:29:32 UTC 2010 x86_64 GNU/Linux The problem is that I can't reboot it. It just hangs after "Will now restart" message. I've already tried: reboot=b, reboot=a, reboot=h kernel options. Nothing helps. Additional info (I can provide any other information): dmidecode System Information Manufacturer: Dell Inc. Product Name: Studio 540 lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 3 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller 02:00.0 FireWire (IEEE 1394): JMicron Technologies, Inc. Device 2380 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

  Read the article

• NetApp FAS270 head doesn't see disks

  - by wfaulk

  I have an FAS270C. For months, I've been running it in a split-head manner (that is, with each head serving data totally independently, and without any clustering even being enabled) in order to facilitate moving some data around. I finally got everything situated, moved all the data to one of the heads, and was trying to get clustering set back up. Now when I try to install OnTap onto the "new" head, it cannot see any of the disks in the head shelf. (That is, the shelf into which the heads are inserted.) I've booted into maintenance mode, and it shows me that the 0b adapter, which should be the adapter that that shelf and its disks should be presented on, is in "OFFLINE (physical)" state. If I try to enable it with either "storage enable adapter 0b" or "fcadmin online 0b", it waits for about 30 seconds and then says: [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 0b. [fci.adapter.online.failed:error]: Fibre Channel adapter 0b failed to come online. There is currently nothing attached to its external 0b port. I've tried it with and without an SFP plugged into it, and with and without its internal termination switch on. The currently active head can see those disks, and can see that two of them are assigned to the other head. Before I started reconfiguring, the "new" head could see disks on that shelf. They may even be the same disks that OnTap was installed on previously. Does anyone have any idea how to proceed?

  Read the article

• Default browser hangs

  - by Craig Hinrichs

  Intermittent hangs would occur when I would use Internet Explorer to open a new main page or new tab to a site I know would be up. The browser would open and say "Waiting for site example.com" and do nothing more. If I closed the window and reopened it it would immediately connect. Over time I would have to close and reopen the window to get to the page. This would happen to any page, including Google. Got sick of it and started using Chrome. I recently upgraded my anti-virus and am now experiencing the same issue with Chrome. I use AVG for my antivirus. Empirically it seems that if I don't make Chrome my default browser I don't experience the issue. I tested this theory for over two hours yesterday. Possible issues I have found this could be but not confirmed yet: MTU settings are not correct. I am infected but my antivirus has not caught it (unlikely but possible) ?? I would like to think this is related to my antivirus but I am unsure how to verify. I don't like the idea of killing my antivirus if #2 is a possibility. I am looking for tips on how I can troubleshoot possible issues.

  Read the article

• Why won't Google Chrome install on my Windows 7?

  - by quakkels

  I can tell something is wrong with my computer. A little history: Google Chrome was not running correctly. When i was using facebook, any link on face that ran an ajax javascript function would not work. No error was being thrown, it just wasn't working. I uninstalled Chrome and reinstalled it. On re-install, a toolbar automatically installed with Chrome. BitTorrentBar. I did not install BitTorrentBar, it installed on it's own. Bad. When BitTorrentBar was active, then ajax functions on facebook worked. When I deactivated or uninstalled BittorrentBar from Chrome extensions, then ajax stopped working. I ran scanned the computer with Avast (free version) and SpyBot Search and Destroy (also free). They found nothing wrong. I uninstalled Chrome using Control Panel and then I went through my file system deleting anything that had "google", "BitTorrent", "chrome", or "conduit". Conduit seems to distribute BitTorrentBar. After doing all that, I tried to reinstall Chrome. I got this error: System.ComponentModel.Win32Exception: The system cannot find the file specified at System.Diagnostics.Process.StartWithShellExecuteEx(ProcessStartInfo startInfo) at System.Diagnostics.Process.Start() at System.Diagnostics.Process.Start(ProcessStartInfo startInfo) at ClickOnceBootStrap.ClickOnceEntry.Main() This error interupts the Chrome install every time! computer scans don't show anything wrong. So then, I thought this might be a .net framework error. Perhaps I deleted something I wasn't supposed to. So I reinstalled .NET Framework 4 and checked the repair option. I also ran Windows Updates. When I tried to download Chrome, again I got the same error as listed above. What should I do?

  Read the article

• Window Management for Mac OS X

  - by Paolo Maffei

  Ok, I feel dumb. I've put many hours into this and found nothing, yet. When I was using Windows I had this little tool called WinSplit Revolution. What it did was letting you divide your screen into how many and of how much size you choose "virtual monitors". You set one time of you want to divide your monitor, then everytime WinSplit is opened the monitor is automatically divided into Virtual Monitors. Screenshots: http://www.google.com/images?hl=en&q=winsplit%20revolution&um=1&ie=UTF-8&source=og&sa=N&tab=wi&biw=1045&bih=499 I'm now using a 30' which i want almost always divided into 4 equal size "virtual monitors" (plus my mbp 13' those will be 5 1280x800 virtual monitors) Now I've switched to Mac OS X and can't find anything that does just this efficiently. I tried Divvy but I found no way to divide my screen into arbitrary "virtual monitors", I need a couple of clicks to select a 3x3 space on a 9x9 grid. Before starting coding something like this can you tell me if you already know of some software that does window management like this?

  Read the article

< Previous Page | 459 460 461 462 463 464 465 466 467 468 469 470  | Next Page >