Search Results

Search found 12588 results on 504 pages for 'memory allocation'.

Page 465/504 | < Previous Page | 461 462 463 464 465 466 467 468 469 470 471 472  | Next Page >

• Linux RAID-0 performance doesn't scale up over 1 GB/s

  - by wazoox

  I have trouble getting the max throughput out of my setup. The hardware is as follow : dual Quad-Core AMD Opteron(tm) Processor 2376 16 GB DDR2 ECC RAM dual Adaptec 52245 RAID controllers 48 1 TB SATA drives set up as 2 RAID-6 arrays (256KB stripe) + spares. Software : Plain vanilla 2.6.32.25 kernel, compiled for AMD-64, optimized for NUMA; Debian Lenny userland. benchmarks run : disktest, bonnie++, dd, etc. All give the same results. No discrepancy here. io scheduler used : noop. Yeah, no trick here. Up until now I basically assumed that striping (RAID 0) several physical devices should augment performance roughly linearly. However this is not the case here : each RAID array achieves about 780 MB/s write, sustained, and 1 GB/s read, sustained. writing to both RAID arrays simultaneously with two different processes gives 750 + 750 MB/s, and reading from both gives 1 + 1 GB/s. however when I stripe both arrays together, using either mdadm or lvm, the performance is about 850 MB/s writing and 1.4 GB/s reading. at least 30% less than expected! running two parallel writer or reader processes against the striped arrays doesn't enhance the figures, in fact it degrades performance even further. So what's happening here? Basically I ruled out bus or memory contention, because when I run dd on both drives simultaneously, aggregate write speed actually reach 1.5 GB/s and reading speed tops 2 GB/s. So it's not the PCIe bus. I suppose it's not the RAM. It's not the filesystem, because I get exactly the same numbers benchmarking against the raw device or using XFS. And I also get exactly the same performance using either LVM striping and md striping. What's wrong? What's preventing a process from going up to the max possible throughput? Is Linux striping defective? What other tests could I run?

  Read the article

• How to stop a random ramp in FCGI Processes Killing the server

  - by Andy Main

  So got the below earlier to day... Around that time the logs show a ramp in processes(600) and associated memory (1.2g), cpu usage load average (80) untill the server gave out. Server had to be hard reset by host as there was no ssh or plesk panel access. Fast CGI is configured as below and is setup for one high use site. As I understand it FcgidMaxProcesses 20 should protect against what happen but has not. I've read many forums with differing answers and references to many different fcgi directives, but have found nothing conclusive. Any one got some definitive answers on how to stop this sort of server process ramping and subsequent server failure? If you need more info let me know. Cheers Andy  /var/log/apache2/error_log [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17651 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17650 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17649 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17644 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17643 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17638 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17633 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17627 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17622 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17674 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17673 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17672 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17667 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17666 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17665 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17664 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17659 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17658 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17657 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17656 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17651 graceful kill fail, sending SIGKILL https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VRmFLWEZfR2VBb2M https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VWTcwZEhoV2Fqejg https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VUUtVWWFINHZjZ0U https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VZEVMclh6ZUdaOUE <IfModule mod_fcgid.c> <IfModule !mod_fastcgi.c> AddHandler fcgid-script fcg fcgi fpl </IfModule> FcgidIPCDir /var/lib/apache2/fcgid/sock FcgidProcessTableFile /var/lib/apache2/fcgid/shm FcgidIdleTimeout 40 FcgidProcessLifeTime 30 FcgidMaxProcesses 20 FcgidMaxProcessesPerClass 20 FcgidMinProcessesPerClass 0 FcgidConnectTimeout 30 FcgidIOTimeout 120 FcgidInitialEnv RAILS_ENV production FcgidIdleScanInterval 10 FcgidMaxRequestLen 1073741824 </IfModule>

  Read the article

• OpenVPN Client timing out

  - by Austin

  I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

  Read the article

• mysql: job failded to start. mysqld.sock is missing

  - by Freefri

  How can I fix this and start mysql-server? After /etc/init.d/mysql start or service mysql start I get the message start: "Job failed to start" And after # mysqld I get this: mysqld 121123 11:33:33 [ERROR] Can't find messagefile '/usr/share/mysql/errmsg.sys' 121123 11:33:33 [Note] Plugin 'FEDERATED' is disabled. mysqld: Unknown error 1146 121123 11:33:33 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 121123 11:33:33 InnoDB: The InnoDB memory heap is disabled 121123 11:33:33 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121123 11:33:33 InnoDB: Compressed tables use zlib 1.2.3.4 121123 11:33:33 InnoDB: Initializing buffer pool, size = 128.0M 121123 11:33:33 InnoDB: Completed initialization of buffer pool 121123 11:33:33 InnoDB: highest supported file format is Barracuda. 121123 11:33:33 InnoDB: Waiting for the background threads to start 121123 11:33:34 InnoDB: 1.1.8 started; log sequence number 1595675 121123 11:33:34 [ERROR] Aborting 121123 11:33:34 InnoDB: Starting shutdown... 121123 11:33:35 InnoDB: Shutdown completed; log sequence number 1595675 121123 11:33:35 [Note] I try to do what mysql say me to do: mysql_upgrade Looking for 'mysql' as: mysql Looking for 'mysqlcheck' as: mysqlcheck Running 'mysqlcheck' with connection arguments: '--port=3306' '--socket=/var/run/mysqld/mysqld.sock' mysqlcheck: Got error: 2002: Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) when trying to connect FATAL ERROR: Upgrade failed And yes, /var/run/mysql is empty: mysql_upgrade Looking for 'mysql' as: mysql Looking for 'mysqlcheck' as: mysqlcheck Running 'mysqlcheck' with connection arguments: '--port=3306' '--socket=/var/run/mysqld/mysqld.sock' mysqlcheck: Got error: 2002: Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) when trying to connect FATAL ERROR: Upgrade failed And this is my file /etc/mysql/my.cnf # cat /etc/mysql/my.cnf |grep sock # Remember to edit /etc/mysql/debian.cnf when changing the socket location. socket = /var/run/mysqld/mysqld.sock socket = /var/run/mysqld/mysqld.sock socket = /var/run/mysqld/mysqld.sock Then I try to reinstall mysql from cero: apt-get purge mysql-client mysql-common mysql-server rm -R /var/lib/mysql rm -R /etc/mysql rm -R /var/run/mysqld userdel mysql apt-get install mysql-server mysql-client Then, after typing my root password for mysql I get this error: | Unable to set password for the MySQL "root" user ¦ ¦ ¦ ¦ An error occurred while setting the password for the MySQL administrative ¦ ¦ user. This may have happened because the account already has a password, or ¦ ¦ because of a communication problem with the MySQL server. ¦ ¦ ¦ ¦ You should check the account's password after the package installation. ¦ ¦ ¦ ¦ Please read the /usr/share/doc/mysql-server-5.5/README.Debian file for more ¦ ¦ information. And again I can't start mysql getting the same messages.

  Read the article

• Forms authentication failed between web server and sql server

  - by Matt Bear

  I've actually found the solution, but I'm trying to understand why it failed, and why my solution fixed the problem. We have an application that uses forms authentication between a web server and sql server, web server runs server 2008, sql server runs 2008 r2, and sql server 2008. In august the sql server was patched with .net 3.5.1, the web server was untouched, and the forms authentication continued to work. 1 week ago we virtualized the web server onto our vSphere server because of failing hardware. Afterwards the form authentication failed with event code 4005, detail code 50201, The ticket supplied was invalid (on the sql server). In fact the sql server started generating Schannel errors and began blue screening 3-4 times a day. At this point I touched the sql server for the first time(ever), the errors were non specific, any reference to them I could find had to do with either zone alarm(which we don't run), or memory errors. So I applied service pack 1, which stopped the blue screening, but did not fix the forms authentication. At this point we had a work around, so we put it on the back burner while we completed another project, and I was able to get back on it last night. First thing was to adjust some code in the webconfig file on the sql server, nothing, next was regenerate and change out the machine key, still no change. Update the DNS servers, no change. Finally I went through and installed all windows updates, two reboots, (over RDP installed a network card driver which failed, and did not have my server room key, that was fun). After that, forms authentication was working again. And the sql server stopped generating as many errors, I've gotten two schannel errors since then. In short, forms authentication began failing when the web server was cloned onto a virtual machine, which caused the sql server to blue sceen? and forms authentication to fail. And could only be fixed by applying patches to the sql server?(I'm wishing I had patched the servers one at a time so I could know for sure which patch on which server fixed it). My question is why did it fail, and why did patching fix it? I hate fixing something without fully understanding the why and how.

  Read the article

• Need Windows XP VGA driver for i3 Haswell

  - by AFH

  Background: I have recently upgraded my hardware because the previous Pentium system started failing to the point that it would not run long enough to boot. It was obviously a hardware fault, but I had no way of knowing whether it was in the motherboard, CPU or memory. Not all the components were now available, so I decided to replace all three. In order to get some benefit from the expenditure, I though I would put in faster components, and for future-proofing went for recently released ones: MSI Z87-G41-PCMate and Intel i3-4130 with 4400 HD graphics. The system performs excellently with Ubuntu 13.10, so I know there are no hardware problems, but I need to continue running XP because it runs several thousand pounds (UK) worth of software, which meets my needs more than adequately: in some cases there is no longer support for later Windows releases, and in most others an expensive and to me unnecessary upgrade is required. Problem: The motherboard specifications claim Windows XP support for the live driver update utility, which misled me into believing that XP drivers were available. Not true: Intel have apparently refused to provide XP drivers for Haswell chips. The update program runs on XP, but finds no suitable Intel drivers. The system is more or less running on the default fail-safe VGA driver, but DirectX will not load, which stops a number of my applications from running. I have been trawling the internet for a month now, but I have not found a graphics driver which will load successfully: all show "This device cannot start. (code 10)". I don't need HDMI support: my monitor is 1280x1024 and connected through the VGA port, so all I need is a driver which will handle this resolution well enough to support DirectX. Has anyone found a driver which will do this? Please don't reply with information found from internet searches, unless you have actually solved this problem: be assured that I have been all round the houses looking at solutions which others have reported as working, but none of them does for me. Incidentally, I did find an Intel HD sound driver which XP accepts (winxp_145111.exe from Intel), though without connecting to an HDMI port on a TV or sound system I have no idea if it works in practice. However, the graphics section of the same driver fails, like all the others I've tried.

  Read the article

• ubuntu eth0 not reconnecting after cable unplugged

  - by Alex

  I'm running kubuntu 9.10 w/ gnome, I have a static IP defined in /etc/network/interfaces When I unplugged my network cable and rebooted, then reconnected the network cable I was not able to connect. I tried using sudo ifup eth0, and then ifconfig and it seemed as though the IP address had been assigned and I was connected, but I wasn't. I then did ifdown eth0, and again ifup eth0. For some reason I'm not able to access the network. Furthermore, I also attempted to connect via wlan, and was able to connect to the wireless network, but cannot "see" the network. I can't transfer data or access the internet or anything on the network including the router. How do I resolve this? topsy@monolyth:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:25:1c:df:70 inet addr:192.168.1.145 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:25ff:fe1c:df70/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5720 errors:0 dropped:0 overruns:0 frame:0 TX packets:565 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:378035 (378.0 KB) TX bytes:46832 (46.8 KB) Memory:fe000000-fe020000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) By access the network I mean the local network as well as the internet. topsy@monolyth:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=9.14 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.24 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.01 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=1.00 ms [snip... all OK, icmp_seq from 5-30, time between 0.981-1.25ms] ^C --- 192.168.1.1 ping statistics --- 30 packets transmitted, 30 received, 0% packet loss, time 29035ms rtt min/avg/max/mdev = 0.971/1.300/9.140/1.458 ms topsy@monolyth:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 root@monolyth:~# cat /etc/resolv.conf # Generated by NetworkManager

  Read the article

• SSH login very slow on OS X Leopard

  - by acjohnson55

  My SSH sessions take a very long time to initiate. This applies for logins with and without passwords, interactive and non-interactive. I have tried setting 'GSSAPIAuthentication no' and 'IPQoS 0x00' on the client side, and 'UseDNS no' on the server side, but no dice. I'm really stumped and frustrated. The worst part is that it SFTP takes forever to establish connections too, making file transfer much longer than it would be otherwise. I thought the problem might be something with PAM, because of where the hang is in the sshd log below, so I tried commenting out each line one-by-one in the /etc/pam.d/sshd file. Some caused login to be impossible, some had no apparent effect. I can't really tell if PAM is stalling for other services, but I can say that su'ing into my account from another account with 'su -l' has no apparent delay. I tried creating a new user account, just to see if there was something wrong with my existing account, and the same problem persisted. Any ideas of what's going on? On the client side, the most verbose mode outputs (redacted where reasonable): OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data ... debug1: ... line 1: Applying options for ... debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 53: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to ... [x.x.x.x] port 22. debug1: Connection established. debug1: identity file /.../.ssh/id_rsa type -1 debug1: identity file /.../.ssh/id_rsa-cert type -1 debug3: Incorrect RSA1 identifier debug3: Could not load "/.../.ssh/id_dsa" as a RSA1 public key debug1: identity file /.../.ssh/id_dsa type 2 debug1: identity file /.../.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.2 debug1: match: OpenSSH_5.2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug2: fd 3 setting O_NONBLOCK debug3: load_hostkeys: loading entries for host "..." from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],ssh-rsa debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],ssh-rsa,[email protected],[email protected],ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 136/256 debug2: bits set: 523/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ... debug3: load_hostkeys: loading entries for host "..." from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug3: load_hostkeys: loading entries for host "x.x.x.x" from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug1: Host '...' is known and matches the RSA host key. debug1: Found key in /.../.ssh/known_hosts:9 debug2: bits set: 492/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /.../.ssh/id_dsa (0x7f8b7b41d6c0) debug2: key: /.../.ssh/id_rsa (0x0) debug1: Authentications that can continue: publickey,password,keyboard-interactive debug3: start over, passed a different list publickey,password,keyboard-interactive debug3: preferred publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering DSA public key: /.../.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-dss blen 434 debug2: input_userauth_pk_ok: fp ... debug3: sign_and_send_pubkey: DSA ... debug1: Authentication succeeded (publickey). Authenticated to ... ([x.x.x.x]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. ****** Hangs here ****** debug2: callback start debug2: client_session2_setup: id 0 debug2: fd 3 setting TCP_NODELAY debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env TERM_PROGRAM debug3: Ignored env SHELL debug3: Ignored env TERM debug3: Ignored env TMPDIR debug3: Ignored env Apple_PubSub_Socket_Render debug3: Ignored env TERM_PROGRAM_VERSION debug3: Ignored env TERM_SESSION_ID debug3: Ignored env USER debug3: Ignored env COMMAND_MODE debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env Apple_Ubiquity_Message debug3: Ignored env __CF_USER_TEXT_ENCODING debug3: Ignored env PATH debug3: Ignored env MKL_NUM_THREADS debug3: Ignored env PWD debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env DYLD_LIBRARY_PATH debug3: Ignored env PYTHONPATH debug3: Ignored env LOGNAME debug3: Ignored env DISPLAY debug3: Ignored env SECURITYSESSIONID debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 On the server side, the debug output looks like: Sep 16 18:46:40 ... sshd[31435]: debug1: inetd sockets after dupping: 3, 4 Sep 16 18:46:40 ... sshd[31435]: Connection from x.x.x.x port 52758 Sep 16 18:46:40 ... sshd[31435]: debug1: Current Session ID is 56AC0FB0 / Session Attributes are 00008000 Sep 16 18:46:40 ... sshd[31435]: debug1: Running in inetd mode in a non-root session... assuming inetd created the session for us. Sep 16 18:46:40 ... sshd[31435]: debug1: Client protocol version 2.0; client software version OpenSSH_5.9 Sep 16 18:46:40 ... sshd[31435]: debug1: match: OpenSSH_5.9 pat OpenSSH* Sep 16 18:46:40 ... sshd[31435]: debug1: Enabling compatibility mode for protocol 2.0 Sep 16 18:46:40 ... sshd[31435]: debug1: Local version string SSH-2.0-OpenSSH_5.2 Sep 16 18:46:40 ... sshd[31435]: debug1: Checking with Service ACLs for ssh login restrictions Sep 16 18:46:40 ... sshd[31435]: debug1: call to mbr_user_name_to_uuid with <...> suceeded to retrieve user_uuid Sep 16 18:46:40 ... sshd[31435]: debug1: Call to mbr_check_service_membership failed with status <0> Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: initializing for "..." Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: setting PAM_RHOST to "x.x.x.x" Sep 16 18:46:40 ... sshd[31435]: Failed none for ... from x.x.x.x port 52758 ssh2 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys2 Sep 16 18:46:40 ... sshd[31435]: debug1: fd 5 clearing O_NONBLOCK Sep 16 18:46:40 ... sshd[31435]: debug1: matching key found: file /.../.ssh/authorized_keys2, line 1 Sep 16 18:46:40 ... sshd[31435]: Found matching DSA key: ... Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys2 Sep 16 18:46:40 ... sshd[31435]: debug1: fd 5 clearing O_NONBLOCK Sep 16 18:46:40 ... sshd[31435]: debug1: matching key found: file /.../.ssh/authorized_keys2, line 1 Sep 16 18:46:40 ... sshd[31435]: Found matching DSA key: ... Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: ssh_dss_verify: signature correct Sep 16 18:46:40 ... sshd[31435]: debug1: do_pam_account: called Sep 16 18:46:40 ... sshd[31435]: Accepted publickey for ... from x.x.x.x port 52758 ssh2 Sep 16 18:46:40 ... sshd[31435]: debug1: monitor_child_preauth: ... has been authenticated by privileged process Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: establishing credentials ***** Hangs here ***** Sep 16 18:46:54 ... sshd[31435]: User child is on pid 31654 Sep 16 18:46:54 ... sshd[31654]: debug1: PAM: establishing credentials Sep 16 18:46:54 ... sshd[31654]: debug1: permanently_set_uid: 509/20 Sep 16 18:46:54 ... sshd[31654]: debug1: Entering interactive session for SSH2. Sep 16 18:46:54 ... sshd[31654]: debug1: server_init_dispatch_20 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_open: ctype session rchan 0 win 1048576 max 16384 Sep 16 18:46:54 ... sshd[31654]: debug1: input_session_request Sep 16 18:46:54 ... sshd[31654]: debug1: channel 0: new [server-session] Sep 16 18:46:54 ... sshd[31654]: debug1: session_new: session 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_open: channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_open: session 0: link with channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_open: confirm session Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_global_request: rtype [email protected] want_reply 0 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request pty-req reply 1 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req pty-req Sep 16 18:46:54 ... sshd[31654]: debug1: Allocating pty. Sep 16 18:46:54 ... sshd[31435]: debug1: session_new: session 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_pty_req: session 0 alloc /dev/ttys008 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request env reply 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req env Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request shell reply 1 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req shell Sep 16 18:46:54 ... sshd[31655]: debug1: Setting controlling tty using TIOCSCTTY.

  Read the article

• SSD Fresh Does Not Start

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• Kickstart based installation of RHEL 6.4 from USB

  - by Peter

  I want to setup some brand new servers with RHEL 6.4. Servers do not have DVD, so, I have to use USB for the installation. I already have a custom ISO with a kickstart file that I use on servers with DVD flawlessly. I used iso2usb to move the ISO t? my USB. When I boot from the USB, the ks file is found, anaconda starts, but then stops with the following error: "The installation source given by device ['sda1'] could not be found. Please check your parameters and try again" Notes: The USB IS the sda. My custom ISO file is renamed to linux.iso from iso2usb and it is present in the root directory of the USB. Kickstart file has the following entry: harddrive --partition=sda1 --dir=/ Please help me to automate the installation with kickstart. Edit 1: This the anaconda.log file: 09:01:57,029 INFO : no /etc/zfcp.conf; not configuring zfcp 09:01:57,259 INFO : created new libuser.conf at /tmp/libuser.4rAbps with instPath="/mnt/sysimage" 09:01:57,259 INFO : anaconda called with cmdline = ['/usr/bin/anaconda', '--stage2', 'hd:sda1:///images/install.img', '--dlabel', '--kickstart', '/tmp/ks.cfg', '--graphical', '--selinux', '--lang', 'en_US.UTF-8', '--keymap', 'us', '--repo', 'hd:sda1:/'] 09:01:57,260 INFO : Display mode = g 09:01:57,260 INFO : Default encoding = utf-8 09:01:59,444 DEBUG : X server has signalled a successful start. 09:01:59,446 INFO : Starting window manager, pid 1345. 09:01:59,537 INFO : Starting graphical installation. 09:01:59,741 INFO : Detected 7968M of memory 09:01:59,741 INFO : Swap attempt of 7968M 09:02:00,840 INFO : ISCSID is /usr/sbin/iscsid 09:02:00,840 INFO : no initiator set Edit 2: This is the part of anaconda log that indicates that it found the USB etc: 09:01:47,918 INFO : starting STEP_STAGE2 09:01:47,918 INFO : partition is sda1, dir is //images/install.img 09:01:47,918 INFO : mounting device sda1 for hard drive install 09:01:48,005 INFO : Path to stage2 image is /mnt/isodir///images/install.img 09:01:54,214 INFO : mounted loopback device /mnt/runtime on /dev/loop0 as /tmp/install.img 09:01:54,214 INFO : Looking for updates for HD in /mnt/isodir///images/updates.img 09:01:54,214 INFO : Looking for product for HD in /mnt/isodir///images/product.img 09:01:54,227 INFO : got stage2 at url hd:sda1:///images/install.img 09:01:54,254 INFO : Loading SELinux policy 09:01:54,700 INFO : getting ready to spawn shell now 09:01:54,975 INFO : Running anaconda script /usr/bin/anaconda 09:01:56,882 INFO : _Fedora is the highest priority installclass, using it 09:01:56,921 INFO : Running kickstart %%pre script(s) 09:01:56,922 WARNING : '/bin/sh' specified as full path 09:01:56,926 INFO : All kickstart %%pre script(s) have been run

  Read the article

• Secret, unlogged, transparent, case-sensitive proxy in IIS6?

  - by Ian Boyd

  Does IIS have a secret, unlogged, transparent, case-sensitive proxy built into it? A file exists on the web-server: GET http://www.stackoverflow.com/javascript/ModifyQuoteArea.js HTTP/1.1 Accept: text/html, application/xhtml+xml, */* Accept-Language: en-US User-Agent: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; WOW64; Trident/5.0) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: www.stackoverflow.com HTTP/1.1 200 OK Connection: Keep-Alive Content-Length: 29246 Date: Mon, 07 Mar 2011 14:20:07 GMT Content-Type: application/x-javascript ETag: "5a0a6178edacb1:1c51" Server: Microsoft-IIS/6.0 Last-Modified: Fri, 02 Tue 2010 17:03:32 GMT Accept-Ranges: bytes X-Powered-By: ASP.NET ... Problem is that a changes made to the file will not get served, the old (i.e. February of last year) version keeps getting served: HTTP/1.1 200 OK Connection: Keep-Alive Content-Length: 29246 Date: Mon, 07 Mar 2011 14:23:07 GMT Content-Type: application/x-javascript ETag: "5a0a6178edacb1:1c51" Server: Microsoft-IIS/6.0 Last-Modified: Fri, 02 Tue 2010 17:03:32 GMT Accept-Ranges: bytes X-Powered-By: ASP.NET ... The same old file gets served, even though we've: renamed the file deleted the file restarted IIS The request for this file does not appear in the IIS logs (e.g. C:\WINNT\System32\LogFiles\W3SVC7\) And this only happens from the outside (i.e. the internet). If you issue the request locally on the server, then you will: - get the current file (file there) - 404 (file renamed) - 404 (file deleted) But if i change the case of the requested resource, i.e.: GET http://www.stackoverflow.com/javascript/MoDiFyQuOtEArEa.js HTTP/1.1 Accept: text/html, application/xhtml+xml, */* Accept-Language: en-US User-Agent: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; WOW64; Trident/5.0) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: www.stackoverflow.com Note: MoDiFyQuOtEArEa.js verses ModifyQuoteArea.js Then i do get the proper file (or get the 404 as i expect if the file is renamed or deleted). But any subsequent changes to the file will not show up until i change the case of the file i'm asking for. Checking the IIS logs all indicate that the (internet) requests are all coming the correct client on the internet (i.e. not from some intermediate proxy). Since the file doesn't exist on the hard drive anymore, i conclude that there is a proxy. The requests serviced from this proxy are not logged in the IIS logs. The requests for new files are logged, and from the client IP, not a proxy IP. The proxy is case sensitivie. This does not sound like something Microsoft, or IIS, would do: - a transparent proxy - case-sensitivie - unlogged - surviving restarts of IIS - surviving in a cache for hours i can't believe that our customer's IIS is doing these things. i'm assuming there is some other transparent proxy in front of IIS. Or, does IIS have a transparent, unlogged, case-sensitive, memory based, proxy, that caches content for at least 7 hours? (Come Monday morning, IIS is serving the correct file, unlogged).

  Read the article

• RHEL 6.x on Rackspace Cloud and Dedicated hardware experiencing Redis Timeouts

  - by zhallett

  I just recently set up a mixture of RHEL 6.1 Rackspace cloud hosts and RHEL 6.2 dedicated hosts using Rackconnect. I am experiencing intermittent Redis timeouts from within our Rails 3.2.8 app with Redis 2.4.16 running on the RHEL 6.2 dedicated hosts. There is no network latency or packet loss. Also there are no errors on any interfaces on our cloud or dedicated servers or on the managed firewall from Rackspace. When Redis timesout, there is nothing logged within redis even though it is set up to do debug logging. The only error we receive is from Airbrake saying there was a Redis timeout. Network topology: RHEL 6.1 cloud hosts <--> Alert logic IDS <--> Cisco ASA 5510 <--> RHEL 6.2 dedicated hosts (web nodes) (two way NAT) (db hosts running redis) Ping from db host to web host: 64 bytes from 10.181.230.180: icmp_seq=998 ttl=64 time=0.520 ms 64 bytes from 10.181.230.180: icmp_seq=999 ttl=64 time=0.579 ms 64 bytes from 10.181.230.180: icmp_seq=1000 ttl=64 time=0.482 ms --- web1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999007ms rtt min/avg/max/mdev = 0.359/0.535/5.684/0.200 ms Ping from web host to db host: 64 bytes from 192.168.100.26: icmp_seq=998 ttl=64 time=0.544 ms 64 bytes from 192.168.100.26: icmp_seq=999 ttl=64 time=0.452 ms 64 bytes from 192.168.100.26: icmp_seq=1000 ttl=64 time=0.529 ms --- data1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999017ms rtt min/avg/max/mdev = 0.358/0.499/6.120/0.201 ms Redis config: daemonize yes pidfile /var/run/redis/6379/redis_6379.pid port 6379 timeout 0 loglevel debug logfile /var/lib/redis/log syslog-enabled yes syslog-ident redis-6379 syslog-facility local0 databases 16 save 900 1 save 300 10 save 60 10000 rdbcompression yes dbfilename dump-6379.rdb dir /var/lib/redis maxclients 10000 maxmemory-policy volatile-lru maxmemory-samples 3 appendfilename appendonly-6379.aof appendfsync everysec no-appendfsync-on-rewrite no auto-aof-rewrite-percentage 100 auto-aof-rewrite-min-size 64mb slowlog-log-slower-than 10000 slowlog-max-len 1024 vm-enabled no vm-swap-file /tmp/redis.swap vm-max-memory 0 vm-page-size 32 vm-pages 134217728 vm-max-threads 4 hash-max-zipmap-entries 512 hash-max-zipmap-value 64 list-max-ziplist-entries 512 list-max-ziplist-value 64 set-max-intset-entries 512 zset-max-ziplist-entries 128 zset-max-ziplist-value 64 activerehashing yes Redis-cli info: redis-cli info redis_version:2.4.16 redis_git_sha1:00000000 redis_git_dirty:0 arch_bits:64 multiplexing_api:epoll gcc_version:4.4.6 process_id:4174 uptime_in_seconds:79346 uptime_in_days:0 lru_clock:1064644 used_cpu_sys:13.08 used_cpu_user:19.81 used_cpu_sys_children:1.56 used_cpu_user_children:7.69 connected_clients:167 connected_slaves:0 client_longest_output_list:0 client_biggest_input_buf:0 blocked_clients:6 used_memory:15060312 used_memory_human:14.36M used_memory_rss:22061056 used_memory_peak:15265928 used_memory_peak_human:14.56M mem_fragmentation_ratio:1.46 mem_allocator:jemalloc-3.0.0 loading:0 aof_enabled:0 changes_since_last_save:166 bgsave_in_progress:0 last_save_time:1352823542 bgrewriteaof_in_progress:0 total_connections_received:286 total_commands_processed:507254 expired_keys:0 evicted_keys:0 keyspace_hits:1509 keyspace_misses:65167 pubsub_channels:0 pubsub_patterns:0 latest_fork_usec:690 vm_enabled:0 role:master db0:keys=6,expires=0 edit 1: add redis-cli info output

  Read the article

• CPU Lockup when loading folder of bookmarks in Firefox

  - by Gary M. Mugford

  I am running Firefox 3.6 on WinXPSP3 on a duo Core machine with 4G of memory. I am also running Avast! free anti-virus and ZoneAlarm free firewall, both latest versions. Within the last month, my service provider basically forced me to upgrade to a Docsis 3.0 compliant modem (offered me a deal I couldn't turn down). At that point, I also upgraded to FF3.6. Basically, I am not unhappy with many aspects of this switchover, EXCEPT, when I now load a folder of bookmarks (anywhere from 10 to 38) I get nothing like the load times I experienced a couple of months back. It's taking minutes rather than seconds. And the first bookmark in one of the folders, GMail, rarely loads before timing out. I have used the old trick of powering off the cable modem before my day's work. This used to fix 'load-lag' in the old days. I have switched from my ISP's DNS server to Google, OpenDNS and back. And nothing seems to work currently. It's not my DNS cache. That's been flushed and secondary computers also have the same issue when loading folders. I have watched the CPU usage and loading the folder will send VSMon (ZoneAlarm) usage over 40 percent, AVastSvc (Avast!) over 30 and Firefox will then push the needle to 100. There's a brief burst by SVCHost when the others falter in devouring cycles. Then everything subsides to single digits once the last tab is loaded. The only other nominal nastiness is VSMon ALWAYS hitting 50 percent when ANY program starts downloading content from the internet. If I shutdown ZoneAlarm (and VSMon with it), the same slow loading takes place, but this time System is running 50% plus, again driving the usage to 100 per cent. I have my doubts FF3.6 vs FF3.5 is an issue, since the other computers are still running 3.5 and suffer the same issue. Those computers are on, but inactive, most of the time, being backups. Obviously, when the CPU hits 100, I can't do much of anything in FireFox OR in other programs. Video play through WMPC or VLC is extremely choppy, although it doesn't seem to affect the audio. Any ideas what I can try next? Thanks, GM

  Read the article

• Crashes and freezes after fixing "BOOTMGR is missing" error

  - by Greg-J

  I came back from a 3-day weekend to a computer that was off. I leave my PC on 24/7, so this was odd. Turn it on to get the dreaded "BOOTMGR is missing" screen. Two attempts at Windows Recovery and it booted into Windows fine. After an hour or so, I get a frozen Chrome and my start bar disappears. Ctrl+Alt+Del brings up an error box telling me that Ctrl+Alt+Del failed to work properly. Clicking on any open application triggers an error (I can't recall the error now, but it essentially just said that the application couldn't be found running or something along those lines). I restart, and again, the same thing happens after a while of use. I turn it on, install the 47 updates I have or so, and then restart it. After a while of use (under an hour), it just freezes completely. My thoughts are: SSDs, RAM or PS. My system specs below: (RAID0) 2 x Crucial M4 CT128M4SSD2 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD) CORSAIR Vengeance 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model CML16GX3M4A1600C9 CORSAIR HX Series HX750 750W ATX12V 2.3 / EPS12V 2.91 SLI Ready CrossFire Ready 80 PLUS GOLD Certified Modular Active 1 x ASUS Maximus IV Gene-Z/GEN3 LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard 1 x Hitachi GST Deskstar 7K1000.C 0F10383 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive 1 x Intel Core i7-2600K Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 1 x SAPPHIRE 21197-00-40G Radeon HD 7970 3GB 384-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card 1 x Noctua NH-D14 120mm & 140mm SSO CPU Cooler This is all crammed in a pretty small case (NZXT Vulcan) and has been running perfectly problem-free since January. The only thing out of the ordinary is that there is a fan in the case that is now making noise whereas the case has previously been completely silent. I have no reason to believe this is anything more then correlation, but felt it is worth mentioning. I believe it MAY be the SSDs simply because of the BOOTMGR error, but not sure how to test that theory. My belief that it may be the RAM is simply from experience with frozen machines. I haven't had the time to memtest it, but will. The PS being the culprit is something I've picked up by reading similar threads on various forums, and it seems plausible. I am unsure how to test this though. ANY insight whatsover would be greatly appreciated!

  Read the article

• Resizing Partitions on Live RHEL/cPanel Server

  - by Timothy R. Butler

  I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

  Read the article

• Windows XP installation problems

  - by Samurai Waffle

  I recently asked a question on here, and thought I had it working... Here is a link to it. Windows XP Installation problems So basically I'm having trouble getting XP installed. To sum it up, a computer I have had a boot sector virus, and I used Darik's Nuke and Boot to wipe the hard drive clean. So the hard drive has nothing on it. I had to try and install Windows through a DOS prompt, because for some reason it won't read it off the DVD. The UBCD is able to look at the files located on the DVD I have in, but I can't boot from it for some reason. So I extracted it to a USB drive, booted to DOS and started the setup process. Here's the weird thing with DOS... It can only find the C: drive. The C: drive in DOS is the flash drive that I have in, running DOS. I can't find the hard drive anywhere! So anyways, after starting the setup process, it copied the files over to the "hard drive" (which took 16 hours because the version of DOS I ran couldn't run smartdrv.exe), and it said the computer had to reboot. So I let it reboot, and it stopped and said there is no boot device. So I popped in UBCD that I have installed on a flash drive, and I discovered that it had copied the Windows files over to the flash drive and not the hard drive. It never asked where it should extract the files... So I toyed around with UBCD, ran a memory test on the hard drive to make sure it was fine, and it came out clean. So I'm stuck now. How can I get this installed? Writing this, I came up with an idea. If I copy the DOS startup files over to the hard drive, would I be able to start DOS from it? If so, I believe that could fix my problems. Any help is greatly appreciated, because I am running out of ideas and am at my wits end with this computer.

  Read the article

• CPU overheating after cleaning it

  - by Roberts

  I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

  Read the article

• How to enable caching on Apache / Ubuntu Linux?

  - by Jim Mischel

  I have a large (several megabytes) XML file that's updated rather frequently (every 10 minutes or less) and gets a lot of traffic. I'd like to implement some caching to reduce bandwidth and server load. Looking at the Apache documents, I see a dizzying array of configuration options that involve various combinations of mod_expires, mod_headers, and mod_cache (and variants). I end up running in circles and the results aren't what I expect. I'm comfortable editing the various configuration files if I have some idea what I'm supposed to change. But at the moment I'm poking around in the dark and that's never a comfortable feeling. So, perhaps if I describe what I want, somebody here can take me by the hand and say, "This is what you need to do." Periodically, this file, call it "stuff.xml" is updated and a new version copied to the directory. The external url would be, for example, http://example.com/stuff.xml. Understand, this part works. Whenever I request the file, I get the expected result. But the file is big and I want to save bandwidth, so first I'd like to implement conditional GET semantics with the If-Modified-Since header. How do I do this? I've enabled mod_headers and mod_expired and added the <FilesMatching> section in my httpd.conf as recommended in countless examples I've seen online, but that didn't change the behavior when made a conditional GET request. I always get a status 200 with the entire document. So how the heck do I implement this? That'll cut down on neeless transfers. I'd also like to limit the amount of data transferred. Seeing as this is XML, gzipping it should save me 50% or more. My next step would be to somehow gzip the file and, if it's not too difficult, store it in memory. That'll cut down on per-access data transfer, and also reduce disk transfers. So how do I implement this type of caching? Thanks in advance.

  Read the article

• Why does NX Client for Windows silently closes after connection?

  - by pavel

  Hey! I connect remotely to my Ubuntu server from Vista machine. Now I need to run a GUI application on the server (Wireshark). So I decided to use FreeNX server/client to view Ubuntu GUI on Vista I have successfully installed FreeNX on Ubuntu and NX Client on Vista. I was following this guide Unfortunately, now I found myself stuck with the following problem. At the client, the !M logo window appears, but after a few seconds that window just closes, even without showing any error message. Guys, I'm really stuck, please help! Maybe I should have installed some graphical environment on the server? These are the details from NX client, it seems there are no errors. ----------------- Info: Display running with pid '7768' and handler '0x670d24'. NXPROXY - Version 3.4.0 Copyright (C) 2001, 2007 NoMachine. See http://www.nomachine.com/ for more information. Info: Proxy running in client mode with pid '2168'. Session: Starting session at 'Sat Dec 19 10:58:35 2009'. Warning: Connected to remote version 3.3.0 with local version 3.4.0. Info: Connection with remote proxy completed. Info: Using WAN link parameters 768/24/1/0. Info: Using cache parameters 4/4096KB/16384KB/16384KB. Info: Using pack method 'adaptive-9' with session 'kde'. Info: Using ZLIB data compression 1/1/32. Info: Using ZLIB stream compression 1/1. Info: No suitable cache file found. Info: Forwarding X11 connections to display ':0'. Info: Listening to font server connections on port '11000'. Session: Session started at 'Sat Dec 19 10:58:35 2009'. Info: Established X server connection. Info: Using shared memory parameters 0/0K. Session: Terminating session at 'Sat Dec 19 10:58:37 2009'. Session: Session terminated at 'Sat Dec 19 10:58:37 2009'. -----------

  Read the article

• Encoding multiple video streams with a single avconv invocation

  - by automatthias

  I played with avconv on Ubuntu and I'm now able to e.g. record the desktop with sound from a soundcard. One thing I wanted to do was recording two video inputs at the same time, for instance the desktop and from the webcam. I thought about doing something like this: avconv \ -f alsa \ -i default \ -acodec flac \ -f video4linux2 \ -r 6 \ -i /dev/video0 \ -f x11grab \ -i :0.0 \ out.mkv My thinking was that if you define multiple video inputs, and the .mkv format can handle multiple video streams, avconv will encode 2 video streams and 1 audio stream into one file. But this isn't what happens: avconv version 0.8.4-6:0.8.4-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:11 with gcc 4.7.2 [alsa @ 0x1091bc0] capture with some ALSA plugins, especially dsnoop, may hang. [alsa @ 0x1091bc0] Estimating duration from bitrate, this may be inaccurate Input #0, alsa, from 'default': Duration: N/A, start: 1354364317.020350, bitrate: N/A Stream #0.0: Audio: pcm_s16le, 48000 Hz, 2 channels, s16, 1536 kb/s [video4linux2 @ 0x10923e0] Estimating duration from bitrate, this may be inaccurate Input #1, video4linux2, from '/dev/video0': Duration: N/A, start: 100607.724745, bitrate: 29491 kb/s Stream #1.0: Video: rawvideo, yuyv422, 640x480, 29491 kb/s, 6 tbr, 1000k tbn, 6 tbc [x11grab @ 0x107b2a0] device: :0.0+83,87 -> display: :0.0 x: 83 y: 87 width: 854 height: 480 [x11grab @ 0x107b2a0] shared memory extension found [x11grab @ 0x107b2a0] Estimating duration from bitrate, this may be inaccurate Input #2, x11grab, from ':0.0+83,87': Duration: N/A, start: 1354364318.488382, bitrate: 196761 kb/s Stream #2.0: Video: rawvideo, bgra, 854x480, 196761 kb/s, 15 tbr, 1000k tbn, 15 tbc Incompatible pixel format 'bgra' for codec 'mpeg4', auto-selecting format 'yuv420p' [buffer @ 0x107fcc0] w:854 h:480 pixfmt:bgra [avsink @ 0x10bdf00] auto-inserting filter 'auto-inserted scaler 0' between the filter 'src' and the filter 'out' [scale @ 0x10dc680] w:854 h:480 fmt:bgra -> w:854 h:480 fmt:yuv420p flags:0x4 Output #0, matroska, to '.../out.mkv': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: mpeg4, yuv420p, 854x480, q=2-31, 4000 kb/s, 1k tbn, 15 tbc Stream #0.1: Audio: libvorbis, 48000 Hz, 2 channels, s16 Stream mapping: Stream #2:0 -> #0:0 (rawvideo -> mpeg4) Stream #0:0 -> #0:1 (pcm_s16le -> libvorbis) Press ctrl-c to stop encoding [mpeg4 @ 0x10bd800] rc buffer underflow ^Cframe= 160 fps= 15 q=2.0 Lsize= 3414kB time=10.66 bitrate=2623.0kbits/s video:3273kB audio:131kB global headers:4kB muxing overhead 0.165600% Received signal 2: terminating. I'm not sure if it's the question of mapping (some -map options to add?) or that avconv just can't encode more than 1 video stream at one time. So is it an actual avconv limitation, or a limitation of the available containers, or me simply not finding the right combination of command line options?

  Read the article

• Ubuntu Server 12.04 CPU Load

  - by zertux

  I have a Server (2x Hexa-Core Xeon E5649 2.53GHz w/HT with 32GB RAM and 20000 GB Bandwidth) running Ubuntu Server 12.04 LTS. The server runs LAMP and serves one website only, the estimated number of users is to be ~ 15,000 at the same time. At the moment i have around 2000 users online each of them runs 50 MySQL queries (small values mostly select and insert) from the beginning until the end of the session. Server CPU Load is high at this number of connections while the RAM usage is almost 1GB out of 32GB its worth mentioning that the server was running very fast with no problems at all but am concerned about the load average. http://s12.postimage.org/z7hi6mz3h/photo.png top - 03:02:43 up 9 min, 2 users, load average: 50.83, 30.14, 12.83 Tasks: 432 total, 1 running, 430 sleeping, 0 stopped, 1 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 66.5%id, 33.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32939992k total, 3111604k used, 29828388k free, 84108k buffers Swap: 2048280k total, 0k used, 2048280k free, 1621640k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2860 root 20 0 25820 2288 1420 S 3 0.0 0:11.18 htop 1182 root 20 0 0 0 0 D 2 0.0 0:01.46 kjournald 1935 mysql 20 0 12.3g 161m 7924 S 1 0.5 102:31.45 mysqld 11 root 20 0 0 0 0 S 0 0.0 0:00.38 kworker/0:1 1822 www-data 20 0 247m 25m 4188 D 0 0.1 0:01.81 apache2 2920 www-data 20 0 0 0 0 Z 0 0.0 0:01.20 apache2 <defunct> 2942 www-data 20 0 247m 23m 3056 D 0 0.1 0:00.20 apache2 3516 www-data 20 0 247m 23m 3028 D 0 0.1 0:00.06 apache2 3521 www-data 20 0 247m 23m 3020 D 0 0.1 0:00.09 apache2 3664 www-data 20 0 247m 23m 3132 D 0 0.1 0:00.09 apache2 3674 www-data 20 0 247m 23m 3252 D 0 0.1 0:00.06 apache2 3713 www-data 20 0 247m 23m 3040 D 0 0.1 0:00.09 apache2 1 root 20 0 24328 2284 1344 S 0 0.0 0:03.09 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.01 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 9 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/1:0 root@server:~/codes# vmstat 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 19 0 0 29684012 86112 1689844 0 0 19 590 254 231 48 0 47 5 23 0 0 29704812 86128 1697672 0 0 4 320 11100 8121 77 1 22 0 33 0 0 29671044 86156 1705308 0 0 0 5440 13190 9140 95 1 4 0 33 3 0 29670088 86160 1706288 0 0 0 32932 12275 7297 99 0 1 0 35 0 0 29693456 86188 1710724 0 0 4 676 12701 7867 98 1 1 0 ^C I have not changed any of the default configurations that comes with Ubuntu. Is this load normal for such powerful server ? is there any optimization i can make to Apache/MySQL to minimize the load ? What do you recommend ?

  Read the article

• How to get more information from the system crash

  - by viraptor

  I'd like to debug an issue I'm having with a linux (debian stable) server, but I'm running out of ideas of how to confirm any diagnosis. Some background: The servers are running DL160 class with hardware raid between two disks. They're running a lot of services, mostly utilising network interface and CPU. There are 8 cpus and 7 "main" most cpu-hungry processes are bound to one core each via cpu affinity. Other random background scripts are not forced anywhere. The filesystem is writing ~1.5k blocks/s the whole time (goes up above 2k/s in peak times). Normal CPU usage for those servers is ~60% on 7 cores and some minimal usage on the last (whatever's running on shells usually). What actually happens is that the "main" services start using 100% CPU at some point, mainly stuck in kernel time. After a couple of seconds, LA goes over 400 and we lose any way to connect to the box (KVM is on it's way, but not there yet). Sometimes we see a kernel reporting hung task (but not always): [118951.272884] INFO: task zsh:15911 blocked for more than 120 seconds. [118951.272955] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [118951.273037] zsh D 0000000000000000 0 15911 1 [118951.273093] ffff8101898c3c48 0000000000000046 0000000000000000 ffffffffa0155e0a [118951.273183] ffff8101a753a080 ffff81021f1c5570 ffff8101a753a308 000000051f0fd740 [118951.273274] 0000000000000246 0000000000000000 00000000ffffffbd 0000000000000001 [118951.273335] Call Trace: [118951.273424] [<ffffffffa0155e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 [118951.273510] [<ffffffff804294f6>] schedule_timeout+0x1e/0xad [118951.273563] [<ffffffff8027577c>] __pagevec_free+0x21/0x2e [118951.273613] [<ffffffff80428b0b>] wait_for_common+0xcf/0x13a [118951.273692] [<ffffffff8022c168>] default_wake_function+0x0/0xe .... This would point at raid / disk failure, however sometimes the tasks are hung on kernel's gettsc which would indicate some general weird hardware behaviour. It's also running mysql (almost read-only, 99% cache hit), which seems to spawn a lot more threads during the system problems. During the day it does ~200kq/s (selects) and ~10q/s (writes). The host is never running out of memory or swapping, no oom reports are spotted. We've got many boxes with similar/same hardware and they all seem to behave that way, but I'm not sure which part fails, so it's probably not a good idea to just grab something more powerful and hope the problem goes away. Applications themselves don't really report anything wrong when they're running. I can run anything safely on the same hardware in an isolated environment. What can I do to narrow down the problem? Where else should I look for explanation?

  Read the article

• What presentation software suits my needs?

  - by claws

  Background: I'm teaching biology to 12th grade students. The syllabus I'm teaching is huge. I mean literally, very huge. There is a lot for students to remember. There are no less than 1000 facts (weird names, dates etc) for students to remember. They'll have to remember all of them, they don't have a choice. The notes I compiled for their learning itself is upto 80 printed pages(Just the bullet outline & facts). That's just one chapter. We have 34 chapters. Also my students are very hardworking, they study upto 8-10hrs per day (Yeah! we are from India :). So, I want to ensure maximum retaining by the students at each and every stage (Teaching & Learning). I'm trying to as many memory training techniques as possible. I'm trying to incorporate, mnemonics, strong visual aids (pictures, 3D-animations, real videos etc.), spaced repetition etc. I think MS powerpoint is not suitable for my needs: There are about 200 slides per chapter. Its very easy for students to get lost while teaching. Because the problem with powerpoint is that it gives facts (as bullets) but it doesn't exploit the association & organization (Concept Map) of the content, which helps students learn quickly. I found an amazing software called XMind. You can see the screenshot here. Problem is that it is not as powerpoint in terms of powerpoint. This software can be used for just for concept maps. In the above screenshot, each topic occupies a single slide. I have an Image/picture(Detailed huge picture) and about 5-10 bullet points and probably a video or an animation of somethings. And this XMind is not good at presenting, in terms that it doesn't allow me to set what to present after what. I want to present a top down view, with a slide for each topic. PS: I Don't like prezi.com. I tried but it simply is too confusing for my students. It zooms here and there. I didn't tried it but I've seen few presentations.

  Read the article

• Lag spikes at full CPU usage, maybe video card

  - by Roberts

  I am posting this thread in hurry so few things may be missed (I will update tomorrow). My PC specs: Motherboard Name - Gigabyte GA-945PL-S3 CPU Type - DualCore Intel Core 2 Duo E4300, 1800 MHz (9 x 200) OS - Microsoft Windows 7 Ultimate OS Kernel Type - 32-bit OS Version - 6.1.7601 I bougth a new video card one month ago. GeForce 210. I didn't have any problems. I wanted to overclock it, in other words: "Play with it". So I installed Gigabyte EasyBoost from CD and overclocked the GPU 590 + 110 mhz, memory to max to 960mhz from 800mhz. Benchmarks showed a little bit bigger score. Then I overclocked shader clock from 1405 to [..] (don't remeber really). So I was playing Modern Warfare 2 when off sudden computer froze when I wanted to select team, I was afk before that. I had to reset CMOS. After that I had problems with Skype: unread messages and no sound. Then I figured it out that when ever I open EasyBoost - Skype starts to glitch again. Now I use EVGA Precission X. Now after a month, I cleaned computer and closed the case, it was open all the time. I started to overclock GPU clock only (just a bit) because there was no problems that would stop me. So sometimes on heavy CPU load graphics starts to lag. Dragging a window is painful to watch too. Sometimes the screen freezes for 5 to 10 seconds (I can see that hard disk activity is maximal). You may say that CPU fault it is, isn't it? But sometimes lag spikes starts randomly when CPU load is at maximum. All 3 benchmark softwares (PerformanceTest, NovaBench and MSI Kombustor) shows that performance of my video card has dropped about 25%. BUT! CPU score is lower too. I ignored these problems but when I refreshed Windows Experience Index I was shocked. Month before (in latvian language but not so hard to understand): Now (upgraded RAM): This happened when I tried to capture Minecraft with Fraps on underclocked GPU to 580mhz (def: 590mhz): All drivers are up to date. Average CPU temperature from 55°C to 75°C (at 70°C sometimes starts these lag spikes). Video card's tempratures are from 45°C to 60°C (very hard to reach 60°C). So my hope is that the video card is fine, cause this card is very new and I want to upgrade CPU anyways. Aplogies for my mistakes in vocabulary (I am trying to type this as fast I can).

  Read the article

• Windows 7, weird/annoying explorer problem

  - by Shiki

  First of all, I'm asking the moderators if you could summarize my problem in the Title and modify it according to that. Thanks in advance and sorry, my english is not that good. The problem. It happened on two of my machines already. Once it happens there are many problems with explorer. I'll try to describe at precisely I just can. So. Basically when you create a new folder, you have to hit the enter key TWICE because first it'll throw an error that "there is no such file..". Okay. Then if you try to delete some, this happens also. Renaming is the same. Here is an example. I tried adding a "2" to the end of the folder name, hit enter and got this. Here I can press cancel, nothing happens. If I press retry, the popup disappears and it'll finally change the folder name. I can't come up with anything for this. Using BitDefender (registered, full protection), Windows 7 x86 Ultimate retail (boxed, english version). The other PC had the same anti-virus protection , but it have a Windows 7 x64. Both systems are activated, updated totally. I don't remember installing any new stuff on the PCs. All the stuff on the PCs are legal, no cracked / any other software present. It just happened, so to say. Already reinstalled the other PC because I thought * I * messed up something and its just something FUBAR. However, I dont want to reinstall my laptop also. Any ideas are welcome. (Today I had a strange bug. Windows Explorer had 1.0+gb memory usage with 100% cpu. Killed it, launched a new explorer.exe and thats all. Nothing changed, but it may worth a try. The other PC did NOT have this problem, ever.) Isn't there a registry fix for this or something? :/

  Read the article

< Previous Page | 461 462 463 464 465 466 467 468 469 470 471 472  | Next Page >