Search Results

Search found 12330 results on 494 pages for 'old retired dude'.

Page 465/494 | < Previous Page | 461 462 463 464 465 466 467 468 469 470 471 472  | Next Page >

• I need to understand why my server turned off

  - by Dema

  Our organization was robbed and definitely it was inside job. I was set up. I work as a manager and as system administrator in this organization and everything goes against me. The only clue I have is that someone accidentally or intentionally turned of a server that is in the office indicating that some one was inside at the time that no one should be. This is the only evidence I have that can justify me.  I looked the log files and they show that the Power button was pressed. Can you help me to find out that that was not a bug or systems overheat? I will post the log files and if you will ask more I will gladly provide the information. Messages: Dec 24 21:43:14 jamx shutdown[27883]: shutting down for system halt Dec 24 21:43:15 jamx init: Switching to runlevel: 0 Dec 24 21:43:15 jamx smartd[3047]: smartd received signal 15: Terminated Dec 24 21:43:15 jamx smartd[3047]: smartd is exiting (exit status 0) Dec 24 21:43:15 jamx avahi-daemon[3015]: Got SIGTERM, quitting. Dec 24 21:43:15 jamx avahi-daemon[3015]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::221:85ff:fe11:8221. Dec 24 21:43:15 jamx avahi-daemon[3015]: Leaving mDNS multicast group on interface eth0.IPv4 with address 82.207.41.239. Dec 24 21:43:15 jamx shutdown[27962]: shutting down for system halt Dec 24 21:43:15 jamx saslauthd[2983]: server_exit     : master exited: 2983 Dec 24 21:43:29 jamx nmbd[2921]: [2010/12/24 21:43:29, 0] nmbd/nmbd.c:terminate(58) Dec 24 21:43:29 jamx nmbd[2921]:   Got SIGTERM: going down... Dec 24 21:43:31 jamx clamd[2526]: Pid file removed. Dec 24 21:43:31 jamx clamd[2526]: --- Stopped at Fri Dec 24 21:43:31 2010 Dec 24 21:43:31 jamx clamd[2526]: Socket file removed. Dec 24 21:43:31 jamx mydns[2645]: jamx.org.ua up 9h44m48s (35088s) 117 questions (0/s) NOERROR=117 SERVFAIL=0 NXDOMAIN=0 NOTIMP=0 REFUSED=0 (100% TCP, 117 queries) Dec 24 21:43:31 jamx mydns[2645]: terminated Dec 24 21:43:34 jamx ntpd[2512]: ntpd exiting on signal 15 Dec 24 21:43:34 jamx hcid[2265]: Got disconnected from the system message bus Dec 24 21:43:35 jamx rpc.statd[2167]: Caught signal 15, un-registering and exiting. Dec 24 21:43:35 jamx portmap[28473]: connect from 127.0.0.1 to unset(status): request from unprivileged port Dec 24 21:43:35 jamx auditd[2021]: The audit daemon is exiting. Dec 24 21:43:35 jamx kernel: audit(1293219815.505:4044): audit_pid=0 old=2021 by auid=4294967295 Dec 24 21:43:35 jamx pcscd: pcscdaemon.c:572:signal_trap() Preparing for suicide Dec 24 21:43:36 jamx pcscd: hotplug_libusb.c:376:HPRescanUsbBus() Hotplug stopped Dec 24 21:43:36 jamx pcscd: readerfactory.c:1379:RFCleanupReaders() entering cleaning function Dec 24 21:43:36 jamx pcscd: pcscdaemon.c:532:at_exit() cleaning /var/run Dec 24 21:43:36 jamx kernel: Kernel logging (proc) stopped. Dec 24 21:43:36 jamx kernel: Kernel log daemon terminating. Dec 24 21:43:37 jamx exiting on signal 15 Acpid: [Fri Dec 24 21:43:14 2010] received event "button/power PWRF 00000080 00000001" [Fri Dec 24 21:43:14 2010] notifying client 2382[68:68] [Fri Dec 24 21:43:14 2010] executing action "/bin/ps awwux | /bin/grep gnome-power-manager | /bin/grep -qv grep || /sbin/shutdown -h now" [Fri Dec 24 21:43:14 2010] BEGIN HANDLER MESSAGES [Fri Dec 24 21:43:15 2010] END HANDLER MESSAGES [Fri Dec 24 21:43:15 2010] action exited with status 0 [Fri Dec 24 21:43:15 2010] completed event "button/power PWRF 00000080 00000001" [Fri Dec 24 21:43:15 2010] received event "button/power PWRF 00000080 00000002" [Fri Dec 24 21:43:15 2010] notifying client 2382[68:68] [Fri Dec 24 21:43:15 2010] executing action "/bin/ps awwux | /bin/grep gnome-power-manager | /bin/grep -qv grep || /sbin/shutdown -h now" [Fri Dec 24 21:43:15 2010] BEGIN HANDLER MESSAGES [Fri Dec 24 21:43:15 2010] END HANDLER MESSAGES [Fri Dec 24 21:43:15 2010] action exited with status 0 [Fri Dec 24 21:43:15 2010] completed event "button/power PWRF 00000080 00000002" [Fri Dec 24 21:43:34 2010] exiting

  Read the article

• md/raid:md2: cannot start dirty degraded array, kernel panic

  - by nl-x

  After having made use of a remote power switch, my server did not come back online. When I went to the datacenter and reboot the computer on the spot I see the server booting (I see the centos progress bar with running almost all the way to the end) and eventually giving the following messages: md/raid:md2: cannot start dirty degraded array. md/raid:md2: failed to run raid set. md: pers->run() failed ... md/raid:md2: cannot start dirty degraded array. md/raid:md2: failed to run raid set. md: pers->run() failed ... Kernel panic - not syncing: Attempted to kill init! Pid: 1, comm: init not tainted 2.6.32-279.1.1.el6.i686 #1 Call Trace: [<c083bfbc>] ? panic+0x68/0x11c [<c045a501>] ? do_exit+0x741/0x750 [<c045a54c>] ? do_group_exit+0x3c/0xa0 [<c045a5c1>] ? sys_exit_group+0x11/0x20 [<c083eba4>] ? syscall_call+0x7/0xb [<c083007b>] ? cmos_wake_setup+0x62/0x112 The server runs CentOS and has software raid, and I don't have backups of the raid settings. The only backup I have is of /home and the database dumps. (Glad to at least have those though.) Since the server is an old Dell PowerEdge 1750 with no CD-ROM drive, I have no way of booting the machine from a boot disk. I also remember in the past that the server also wouldn't boot from a bootable USB disk. So the only way I know how to boot the server is to go to the datacenter, pick up the server and take it to the office. Screw open the server. Attach a cdrom drive to an IDE slot on the motherboard. And then boot it. I am hoping you guys could help me avoid this. I have looked a bit through the boot options and I found the following boot options. When CentOS is about to boot and interrupt the boot-countdown: CentOS (2.6.32-279.1.1.el63.i686) CentOS Linux (2.6.32-71.29.1.el6.i686) centos (2.6.32-71.el6.i686) I think the first configuration is the default one, because choosing that gets me to the above mentioned kernel panic. The other ones end with something like "Sleeping forever". I can press 'e' to edit boot commands, press 'a' to modify kernel arguments and press 'c' for grub command line. The command line gives a grub prompt. But I have no idea how to get the system to boot without (trying to) access the dirty partitions. What I want to do is off course: - boot the machine - check hard drive for errors - mark the drive as clean

  Read the article

• SNTP, why do you mock me?!

  - by Matthew

  --- SOLVED SEE EDIT 5 --- My w2k3 pdc is configured as an authoritative time server. Other servers on the domain are able to sync with it if I manually specify it in the peer list. By if I try to sync from flags 'domhier', it wont resync; I get the error message The computer did not resync because no time data was available. I can only think that it is not querying the pdc. I also tried setting the registry as shown here (http://support.microsoft.com/kb/193825). But no luck (I have not restarted the server, I am hoping I wont have to since it is the pdc) If you would like any further information on my config, please let me know. Edit 1: I have set the w32time service config AnnouceFlags to 0x05 as documented here www.krr.org/microsoft/authoritative_time_servers.php and a number of other places. The PDC syncs to an external time source (ntp). I can get the stripchart on the client from the pdc no problems. The loginserver for the host I am trying to configure is shown as the pdc. Edit 2: The packet capture has revealed something interesting. The client is contacting the correct server, and getting a valid response but I still get the same error message. Here is the NTP excerpt from the client to the server Flags: 11.. .... = Leap Indicator: alarm condition (clock not synchronized) (3) ..01 1... = Version number: NTP Version 3 (3) .... .011 = Mode: client (3) Peer Clock Stratum: unspecified or unavailable (0) Peer Polling Interval: 10 (1024 sec) Peer Clock Precision: 0.015625 sec Root Delay: 0.0000 sec Root Dispersion: 1.0156 sec Reference Clock ID: NULL Reference Clock Update Time: Sep 1, 2010 05:29:39.8170 UTC Originate Time Stamp: NULL Receive Time Stamp: NULL Transmit Time Stamp: Nov 8, 2010 01:44:44.1450 UTC Key ID: DC080000 Here is the reply NTP excerpt from the server to the client Flags: 0x1c 00.. .... = Leap Indicator: no warning (0) ..01 1... = Version number: NTP Version 3 (3) .... .100 = Mode: server (4) Peer Clock Stratum: secondary reference (3) Peer Polling Interval: 10 (1024 sec) Peer Clock Precision: 0.00001 sec Root Delay: 0.1484 sec Root Dispersion: 0.1060 sec Reference Clock ID: 192.189.54.17 Reference Clock Update Time: Nov 8,2010 01:18:04.6223 UTC Originate Time Stamp: Nov 8, 2010 01:44:44.1450 UTC Receive Time Stamp: Nov 8, 2010 01:46:44.1975 UTC Transmit Time Stamp: Nov 8, 2010 01:46:44.1975 UTC Key ID: 00000000 Edit 3: dumpreg for paramters on pdc Value Name Value Type Value Data ------------------------------------------------------------------------ ServiceMain REG_SZ SvchostEntry_W32Time ServiceDll REG_EXPAND_SZ C:\WINDOWS\system32\w32time.dll NtpServer REG_SZ bhvmmgt01.domain.com,0x1 Type REG_SZ AllSync and config Value Name Value Type Value Data -------------------------------------------------------------------------- LastClockRate REG_DWORD 156249 MinClockRate REG_DWORD 155860 MaxClockRate REG_DWORD 156640 FrequencyCorrectRate REG_DWORD 4 PollAdjustFactor REG_DWORD 5 LargePhaseOffset REG_DWORD 50000000 SpikeWatchPeriod REG_DWORD 900 HoldPeriod REG_DWORD 5 LocalClockDispersion REG_DWORD 10 EventLogFlags REG_DWORD 2 PhaseCorrectRate REG_DWORD 7 MinPollInterval REG_DWORD 6 MaxPollInterval REG_DWORD 10 UpdateInterval REG_DWORD 100 MaxNegPhaseCorrection REG_DWORD -1 MaxPosPhaseCorrection REG_DWORD -1 AnnounceFlags REG_DWORD 5 MaxAllowedPhaseOffset REG_DWORD 300 FileLogSize REG_DWORD 10000000 FileLogName REG_SZ C:\Windows\Temp\w32time.log FileLogEntries REG_SZ 0-300 Edit 4: Here are some notables from the ntp log file on the pdc. ReadConfig: failed. Use default one 'TimeJumpAuditOffset'=0x00007080 DomainHierachy: we are now the domain root. ClockDispln: we're a reliable time service with no time source: LS: 0, TN: 864000000000, WAIT: 86400000 Edit 5: F&^%ING SOLVED! Ok so I was reading about people with similar problems, some mentioned w32time server settings applied by GPO, but I tested this early on and there were no settings applied to this service by gpo. Others said that the reporting software may not be picking up some old gpo settings applied. So I searched the registry for all w32time instaces. I came across an interesting key that indicated there may be some other ntp software running on the server. Sure enough, I look through the installed software list and there the little F*&%ER is. Uninstalled and now working like a dream. FFFFFFFUUUUUUUUUUUU

  Read the article

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post.

  Read the article

• Causes of sudden massive filesystem damage? ("root inode is not a directory")

  - by poolie

  I have a laptop running Maverick (very happily until yesterday), with a Patriot Torx SSD; LUKS encryption of the whole partition; one lvm physical volume on top of that; then home and root in ext4 logical volumes on top of that. When I tried to boot it yesterday, it complained that it couldn't mount the root filesystem. Running fsck, basically every inode seems to be wrong. Both home and root filesystems show similar problems. Checking a backup superblock doesn't help. e2fsck 1.41.12 (17-May-2010) lithe_root was not cleanly unmounted, check forced. Resize inode not valid. Recreate? no Pass 1: Checking inodes, blocks, and sizes Root inode is not a directory. Clear? no Root inode has dtime set (probably due to old mke2fs). Fix? no Inode 2 is in use, but has dtime set. Fix? no Inode 2 has a extra size (4730) which is invalid Fix? no Inode 2 has compression flag set on filesystem without compression support. Clear? no Inode 2 has INDEX_FL flag set but is not a directory. Clear HTree index? no HTREE directory inode 2 has an invalid root node. Clear HTree index? no Inode 2, i_size is 9581392125871137995, should be 0. Fix? no Inode 2, i_blocks is 40456527802719, should be 0. Fix? no Reserved inode 3 (<The ACL index inode>) has invalid mode. Clear? no Inode 3 has compression flag set on filesystem without compression support. Clear? no Inode 3 has INDEX_FL flag set but is not a directory. Clear HTree index? no .... Running strings across the filesystems, I can see there are what look like filenames and user data there. I do have sufficiently good backups (touch wood) that it's not worth grovelling around to pull back individual files, though I might save an image of the unencrypted disk before I rebuild, just in case. smartctl doesn't show any errors, neither does the kernel log. Running a write-mode badblocks across the swap lv doesn't find problems either. So the disk may be failing, but not in an obvious way. At this point I'm basically, as they say, fscked? Back to reinstalling, perhaps running badblocks over the disk, then restoring from backup? There doesn't even seem to be enough data to file a meaningful bug... I don't recall that this machine crashed last time I used it. At this point I suspect a bug or memory corruption caused it to write garbage across the disks when it was last running, or some kind of subtle failure mode for the SSD. What do you think would have caused this? Is there anything else you'd try?

  Read the article

• pptpd not working externally on Ubuntu Server 11.10

  - by Brendan

  I am trying to set up a pptpd vpn on our newly installed Ubuntu 11.10 64 bit server, but am not having success having a client connect via an iPhone to the VPN. Note that no clients have been able to connect to this VPN from outside of the network. The system is up to date with patches. Here is the output of /var/log/syslog. Please note that 222.153.x.y is my remote IP address. Mar 30 22:07:47 server pptpd[9546]: CTRL: Client 222.153.x.y control connection started Mar 30 22:07:47 server pptpd[9546]: CTRL: Starting call (launching pppd, opening GRE) Mar 30 22:07:47 server pppd[9555]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Mar 30 22:07:47 server pppd[9555]: pppd 2.4.5 started by root, uid 0 Mar 30 22:07:47 server pppd[9555]: Using interface ppp0 Mar 30 22:07:47 server pppd[9555]: Connect: ppp0 <--> /dev/pts/3 Mar 30 22:07:47 server pptpd[9546]: GRE: Bad checksum from pppd. Mar 30 22:08:17 server pppd[9555]: LCP: timeout sending Config-Requests Mar 30 22:08:17 server pppd[9555]: Connection terminated. Mar 30 22:08:17 server pppd[9555]: Modem hangup Mar 30 22:08:17 server pppd[9555]: Exit. Mar 30 22:08:17 server pptpd[9546]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Mar 30 22:08:17 server pptpd[9546]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Mar 30 22:08:17 server pptpd[9546]: CTRL: Reaping child PPP[9555] Mar 30 22:08:17 server pptpd[9546]: CTRL: Client 222.153.x.y control connection finished As you can see, the problem seems to be the connection timing out after 30 seconds ("Mar 30 22:08:17 server pppd[9555]: LCP: timeout sending Config-Requests". Over Wifi however (inside the local network) there are no issues: Mar 30 22:12:33 unreal-server pptpd[12406]: CTRL: Client 192.168.0.100 control connection started Mar 30 22:12:33 unreal-server pptpd[12406]: CTRL: Starting call (launching pppd, opening GRE) Mar 30 22:12:33 unreal-server pppd[12407]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Mar 30 22:12:33 unreal-server pppd[12407]: pppd 2.4.5 started by root, uid 0 Mar 30 22:12:33 unreal-server pppd[12407]: Using interface ppp0 Mar 30 22:12:33 unreal-server pppd[12407]: Connect: ppp0 <--> /dev/pts/3 Mar 30 22:12:33 unreal-server pptpd[12406]: GRE: Bad checksum from pppd. Mar 30 22:12:36 unreal-server pppd[12407]: peer from calling number 192.168.0.100 authorized Mar 30 22:12:36 unreal-server pppd[12407]: MPPE 128-bit stateless compression enabled Mar 30 22:12:36 unreal-server pppd[12407]: Cannot determine ethernet address for proxy ARP Mar 30 22:12:36 unreal-server pppd[12407]: local IP address 192.168.0.10 Mar 30 22:12:36 unreal-server pppd[12407]: remote IP address 192.168.1.1 I have set up an iptables config for the server; to check this isn't the problem I allowed all traffic temporarily, but this does NOT change the symptoms in the first example. Here is the output from /etc/iptables.rules.save *filter :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT Even with these rules applied, the output from /var/log/syslog is LINE FOR LINE what I saw in the the first block of code. Please note that before running this Ubuntu server; an old SME Server box was running in place of it, that had a pptpd server on it just like we are using, and we experienced no issues.

  Read the article

• How to delete files and folders that cannot be deleted?

  - by glenneroo

  I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

  Read the article

• Asus P8P67 Rev. 3.1 Motherboard issues powering on and saving settings

  - by Scott

  Edit: New Information Have some updated information from the old question below: So basically my issue right now is somewhat similar, but I've been able to rule out a couple of things. I don't think this has anything to do with light on the motherboard. No matter what lights are on/off on the motherboard when the computer is off, they don't affect this issue. The main power LED on the Mobo is always lit when the power supply is turned on, and that's what matters anyway. Even when the main power LED is on, the PC will NOT boot up the first time I hit the power switch. I have to go reset the power supply (make all lights turn off on the Mobo and back on), and THEN hit the power switch. Then everything boots up. Also, the BIOS settings are reset every time this happens. Asus Tech Support told me to try jumping the power with something metal to try and rule out that it's a problem with the connectors getting power, or if it's a problem with the case power switch pins - haven't done that yet though. Any ideas? This is a lot simpler than it was before when I thought it had to do with certain LED indicators for RAM, EPU, etc. Original Question So I built my new desktop just about 3 weeks ago. I've been having a few issues which I think are all related to my motherboard, an Asus P8P67 Revision 3.1, but I'm not 100% sure as this is really the first from-scratch build I've ever done. I've posted these questions on the Asus forums, Asus Tech Support, and the Corsair forums as well as I thought it might have something to do with my power supply at one point. None of these avenues have solved my issue until now completely, so I thought I'd come here to see what you guys think. Here's what's happening: My computer is off, and I go to power it on. I press the power switch on the case (Antec Nine Hundred), and nothing seems to happen. Upon further inspection, I see that what this actually does is simply turn on the EPU LED on my motherboard, but doesn't actually boot anything up. I then have to go and flip the main power switch on the power supply off and back on. What this does is turn off all lights on the Motherboard after a few seconds, and turn them all back on (including the EPU LED that was off before I hit the power switch the first time). Now, hitting the power switch works. The machine boots up fine, and starts going through the boot up process. As a side note: My Motherboard is set to "Force BIOS", and every single time I change this to do the opposite, the next time my computer boots up that change reverts itself. I think this may be due to the fact that I am doing the hard reset on the power supply each time, but I'm not sure. I had thought that the Motherboard would keep its BIOS settings unless you did something to the Mobo itself - so this may be a related issue, or something else completely. That's basically it. Once it's on, it's on. It works fine, recognizes all of my hardware, and runs great. All fans/lights in the case work great, and I'm getting standard readings. The next time I go to shut the computer down however, I can expect the same exact process getting it up and running, including being forced to go into BIOS and exit again before I can load Windows. Another side note: If I power on my computer using the power switch DIRECTLY after shutting it down, it powers right back on (I think this is because the EPU LED light doesn't have time to turn off). It looks as if as long as the EPU LED is lit up on the motherboard before I hit the power switch on the case, the thing will boot up fine (although this doesn't explain the "Force BIOS" issue, at least it's something). Any ideas? Thanks guys. P.S. - System Specs Asus P8P67 Rev. 3.1 Motherboard Intel Core i7 2600K Processor 16GB (4x4GB) G-Skill 1600 RAM NVIDIA EVGA GTX 570 Video Card Crucial 128GB SSD HD Corsair 850W Power Supply Seagate 2TB HDD

  Read the article

• e2fsck / resize2fs problems

  - by BlakBat

  I've got 6 drives (each 1.5T, all same model and firmware revision) that are part of a RAID5 array. The RAID5 makes a LVM volume group and a logical group. The latter contains only one ext3 partition. I've recently ran: e2fsck -f /dev/vg03/lv01 && resize2fs -M /dev/vg03/lv01 which exited without an error. Now when I try to mount /dev/vg03/lv01 I get: EXT3-fs error (device dm-0): ext3_check_descriptors: Block bitmap for group 30533 not in group (block 1000532368)! EXT3-fs: group descriptors corrupted! How do I get out of this predicament? This is all the info I can currently give you: fdisk -l /dev/sd[cdefgh] shows (correctly) that they are "Linux raid autodetect" but fdisk now shows: fdisk -l /dev/md0 Disk /dev/md0: 7501.5 GB, 7501495664640 bytes ... Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table (instead of a LVM type partition) fdisk -l /dev/vg03/lv01 Disk /dev/vg03/lv01: 7501.5 GB, 7501491732480 bytes ... Disk identifier: 0x00000000 Disk /dev/vg03/lv01 doesn't contain a valid partition table (instead of a ext3 type partition) I've tried: e2fsck -fy /dev/vg03/lv01 e2fsck 1.41.12 (17-May-2010) e2fsck: Group descriptors look bad... trying backup blocks... Block bitmap for group 30533 is not in group. (block 1000532368) Relocate? yes Inode bitmap for group 30533 is not in group. (block 1000532369) Relocate? yes Pass 1: Checking inodes, blocks, and sizes Relocating group 30533's block bitmap to 1000524246... Error allocating 1 contiguous block(s) in block group 30533 for inode bitmap: Could not allocate block in ext2 filesystem e2fsck: aborted Extra information I can give you: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active (auto-read-only) raid5 sdg1[0] sdh1[5] sdf1[4] sde1[3] sdc1[2] sdd1[1] 7325679360 blocks level 5, 128k chunk, algorithm 2 [6/6] [UUUUUU] bitmap: 1/175 pages [4KB], 4096KB chunk unused devices: Lastly, all smartctl tests (short and extendend) showed no errors on any of the disks. Should I try to resize2fs to grow /dev/vg03/lv01 and redo a e2fsck ? Should I cfdisk /dev/md0 and /dev/vg03/lv01 back to their real types? Thanks in advance for all and any help. 2011-09-20 UPDATE I issued the following commands and was able to remount the partition, but by viewing the size (df) of before and after, it seems that 1Tb of data have gone missing. By checking the MD5SUMS (from an old backup) of some files with the "same" files from the remounted partition, some errors have been detected. Commands issued to remount the partition were: dumpe2fs /dev/vg03/lv01 Block count: 1000491435<br /> Block size: 4096<br /> tune2fs -O ^has_journal /dev/vg03/lv01 resize2fs -p /dev/vg03/lv01 dumpe2fs /dev/vg03/lv01 Block count: 1831418880<br /> Block size: 4096<br /> mount -o ro,noatime /dev/vg03/lv01 /mnt/raid OK... but files have been damaged / gone missing.

  Read the article

• Installing .NET Framework 4 Client Profile breaks Windows Update

  - by Richard

  I have a Samsung NC-10 netbook with a fresh install of Windows 7 Home Premium 32-bit (it only had 2GB). If Microsoft .NET Framework 4 Client Profile is installed on it, Windows Update will always return error code 8024402F ("Windows Update encountered an unknown error"). As soon as I uninstall it, Windows Update works just fine again. Out of the four computers in this house, only this netbook has the problem. My question is: How can I get the .NET Framework 4 Client Profile installed on my netbook and continue to have a functioning Windows Update? ----- More information ----- The hard-drive recently died on my netbook so I replaced it with a nice new SSD and did a fresh installation of Windows 7 Home Premium (SP1) - along with all the updates. At some point I found that, when I ran Windows Update, I was greeted with error code 8024402F ("Windows Update encountered an unknown error"). Looking in C:\Windows\WindowsUpdate.log, I saw the following issue: WARNING: ECP: Failed to validate cab file digest downloaded from http://download.windowsupdate.com/msdownload/update/software/dflt/2012/02/4913552_4a5c9563d1f58c77f30d0d5c9999e4b8bff3ab21.cab with error 0x80091007 WARNING: ECP: This roundtrip contained some optimized updates which failed. New Update count = 0, Old Count = 3 FATAL: ProcessCoreMetadata did not return any update to be committed WARNING: Sync of Updates: 0x8024402f WARNING: SyncServerUpdatesInternal failed: 0x8024402f When I downloaded the CAB from the URL listed and opened it, it contained a file called 4913552.txt. A search on Google suggested that it's related to Microsoft .NET Framework 4 Client Profile. Other people had reported problems with it breaking Windows Update, but they were running Windows XP. I tried the steps outlined on the Microsoft site for this error code, but it reported that there was nothing wrong. I also found this superuser question, I tried all the answers listed but none of them made any difference. My router doesn't block ActiveX, changing my internet settings in IE made no difference, assuming it was a corrupted update repository didn't do anything (except wipe my update history), my date and time was correct, switching to Google's DNS didn't work and neither did disabling IPv6. Figuring that this update was corrupted, I repaired it and nothing changed. In desperation I un-installed it and Windows Update started working again! Brilliant! I then downloaded the full version from the Microsoft website, installed it and, thankfully, Windows Update continued to work just fine. A week later I turn on my netbook and Windows Update is broken again with exactly the same error message and log entries as before. Repairing .NET Framework 4 Client Profile did nothing, removing it entirely solved the problem again. Thinking this might be some odd Windows installation issue, I formatted the hard-drive and re-installed Windows. Same problem as before - as soon as .NET Framework 4 Client Profile ended up on the netbook, Windows Update stopped working and reported error 8024402F. As soon as it was un-installed, everything worked just fine again. There are three other machines in this house and all of them have working Windows Update and this Client Profile. Does anyone know why it causes this netbook to break and, more importantly, how I can fix it?

  Read the article

• How to diagnose and solve an erratic "HDCP Support Required"?

  - by Jom Orgstrom

  I am playing a digital tv broadcast on Windows Media Center for Windows 7. I built this system so it works with HDCP, and in fact I have been able to watch tv and bluray before with this same computer. However, I suddenly started getting an "HDCP Support Required" error from WMC. The entire message is as follows: HDCP Support Required High-bandwidth Digital Content Protection (HDCP) may not be supported by the current video card. Use an HDCP-compliant display, video card, and video driver. Or, connect using an analog connection such as component or VGA. Relevant specs are: CPU: Ivy Bridge Core i7-3770 Motherboard: Asus P8H77-I Memory: 16GB DDR3-1600 Graphics: Radeon HD 7850 (Driver by AMD, version 8.982.0.0 built on 2012/07/27) Display: Acer P243w connected by HDMI Sound: Roland Quad-Capture (It complains even when I use the bundled VIA HD Audio) TV Tuner: I-O Data GV-MC7/HZ3 OS: Windows 7 Professional SP1, Windows Update enabled. All patched and up to date. As you can see, there is nothing weird or old about my setup. I am also not doing anything strange, not doing any overclocking, weird system changes and so on. One thing that does happen from time to time, is that the display goes black for a few seconds (sometimes when watching media contents, sometimes when just using photoshop or Visual Studio). This happened with my previous setup as well, so I'd be inclined to think it is a display or cable issue (apart from the BD drive, these are the only things I kept from my previous setup to this one). But being a digital transfer, as far as I know, these things either work or not. Never erratically or with decreased quality. The thing is that sometimes I can watch the TV, sometimes not. This happens with recorded programs as well, so it's not a per-program thing. Sometimes rebooting helps, sometimes it doesn't. Sometimes unplugging and plugging back the HDMI connector helps, sometimes it doesn't. Sometimes doing so doesn't even turn the screen back on, so I have to reboot. Unfortunately, WMC's error message is quite unhelpful. I'd like to know exactly where the problem is, so I can solve it. I don't want to buy a brand new display just to then find out it was a registry setting that was misconfigured. I've tried looking at the system event viewer, but these errors don't show up at all in there. Other people who have this problem seem to have a setup that is not HDCP compliant, so I turn to you guys here. Anybody knows how to diagnose this problem? Edit: So I got the Cyberlink Blu-ray disc advisor. I ran it and told me everything was okay, except for the Video Connection Type, which showed as "Digital (without HDCP)". I then proceeded to unplug the power cable from the monitor, plugged it in again, ran the tool again, and now it's "Digital (with HDCP)". Needless to say, I can watch my TV and recorded programs on WMP again. I'm guessing that at some point, something may be slightly wrong with the HDCP setup, and Windows decides to reset the entire content protection path (which leads to the screen blanking out). Usually the reset succeeds, but sometimes it doesn't, so Windows defaults to turning HDCP off. There's no way to turn it back on, except by doing a hard reset of the display. I really want to know what the exact error was, so I can fix it. Is it the cable? is it the display? is it the video card? the driver? Also, is there any other way to try and turn HDCP on again without having to hard reset the display? Oh, questions, questions...

  Read the article

• Dell Latitude E6430 Docking Station + Dual Monitor + Laptop Screen Tri-Monitor setup

  - by Larry

  I have a company issued laptop and docking station as well as two monitors The specifications of the hardware are as follows; Laptop: Latitude E6430 BIOS: A02.00 Processor: i7-3720QM CPU @ 2.60 (8 CPUs) Memory: 4096MB RAM Page file: 1825MB used, 4793MB available DirectX 11 Display Driver/Chip: MVIDIA NVS 5200M DAC: Integrated RAMDAC Aprox Total Memory: 2376 (Above 3 details same for both displays) Current Display Mode (Display 1): 1600x900 Current Display Mode (Display 2): 1440x900 the docking station is a Dell Latitude E6420 Docking Station PR03X Port Replicator and I don't think the monitor model is particularly relevant to resolving this issue but they are both Acer V193Ws The story goes like this; the laptop works fine if I VGA one monitor into the laptop through the vga port on the back of the lefthand side of the laptop I can achieve dual monitor display fine (laptop screen + monitor) if I plug the laptop into the docking station and use the vga port in the back of the docking station I can dual monitor fine (laptop screen + monitor) if I plug the laptop into the docking station, the laptop's lefthand side VGA port no longer seems to function at all I've spoken to internal IT about this issue and they're going to get me some kind of VGA splitter or a DVI-VGA adapter to use with the docking station for the second Acer Monitor, but that isn't going to happen for a few days. So I guess what I'm wondering is; is there any way to continue to use the side VGA port on my laptop while using the docking station VGA port? and as a secondary 'followup' pending resolution of the initial issue with getting both monitors up and running (at the moment I have both monitors on my desk but am just using my laptop screen as one of my dual monitor display with one of the monitors [the one connected to dock]), is there any way to CONTINUE to use my laptop monitor to in effect have a triple monitor display (2 monitors + docked laptop)? I am wondering this because internal IT told me that they were aware of some issues with the particular display drivers in my box and triple monitor displays but weren't really going to look TOO much in-depth into that (which is perfectly understandable) since getting the adapter for the dual monitors up and running was the greater priority within their purview. So this is a two parter; Can I dual monitor using two vga cables with 1 docking station vga port and one laptop vga port? is there a setting that can be tweaked somewhere? because plugging the box into the station seems to make the side port stop working and... Is there any reasonably simple and cost-effective work around (e.g. I am find with shelling out maybe a few dollars out of my own pocket for some hardware or software to make my company box tri-display capable) but if this requires some extensive rebuild or new OSs or doing stuff to the BIOS I'd rather have a straight answer about this being untenable as a slight modification to a (once again) company laptop and stop wasting time looking into it Thanks! and please let me know if you guys need any more details (tech specs or something) to answer this question [EDIT] 2/10/2014 Just an update; turned out it really was just a hardware limitation issue. The old laptop just couldn't hack it. Got a new laptop with a better video card and different monitors from my company and am successfully using a triple display currently (2 monitors + laptop screen)

  Read the article

• RAID controller dropping the wrong drive

  - by bramp

  I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

  Read the article

• Why are USB 2.0 devices crashing my system?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic baby-ATX motherboard with no identifying markings. CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. There's one stamp on the motherboard that says "Rev.B". On board it has 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. It has an 80Gb Western Digital hard drive freshly formatted and built with Windows XP Professional with Service Pack 3 and all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 crashes the machine as soon as it starts up). It's got a Daytek MV150 15" touch screen running through the VGA and COM1 with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem If I hook any USB 2.0 devices to this machine, it hangs the whole machine and I have to hard boot it to get it back up. Workarounds found I can plug the same devices into the on board USB 1.0 connectors and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions I've tried disabling all the on board devices that I'm not using - such as the on board LAN, the second COM port, the AGP connector etc. through the BIOS in an (perhaps misguided or futile) attempt to reduce the power consumption... I don't think it had any effect but it didn't do any harm. I was wondering if the PSU wattage just isn't enough to drive the USB 2.0 devices; I've seen this suggested but haven't found any confirmation that this could really be an issue - nor have I found a way to work around this issue - if indeed it is one. Any ideas? The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference. I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself. Other thoughts Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

  Read the article

• Where to download replacement "Explorerframe.DLL" Files for x64 Windows 7 Pro?

  - by Ben Franchuk

  After posting this question, I did some research to reveal what the problem likely was, and found what I need to fix. Following this is the original post, then my updated question. A few months ago I ended up requiring to change my computer's SID to fix a problem it had been having- Instead of fixing the problem, though, it screwed up my at-the-time current install of windows, to the point of me needing to do a fresh install. As I am in possession of an OEM copy of Windows 7 Pro 64 Bit, I successfully reinstalled over the dead copy with that (all the files that were on the computer previous to this windows install were put in a Windows.old folder). Everything installed and worked absolutely fine, except for one thing. The problem I am experiencing is that, in some Windows Explorer windows, the explorer pane doesn't show. Instead, it simply shows a white area where the pane would show. This makes some software not usable, I recently realized; Software such as Cubase, which use just the explorer pane to select file save locations, cannot save at all as the pane itself is... not operational. Below is a screenshot of this problem as it occurs in cubase; ...and again as it shows in UTorrent in the save location selector window. The highlighted area is where the sidebar would NORMALLY be. Pardon my scribbling over some of the things in the window- I would personally rather the internet did not get a glimpse of my files. I have yet to find a common reason why the pane works in some applications when they pull explorer, and others not. I have yet to see it go away, and the software affected by it has been affected since I reinstalled my copy of windows. Initially, I was able to live with it as I can type out save locations in the file name bar to navigate, but with software like Cubase, I do not have this option. Reinstalling windows again is NOT an option. Here's the updated question. After posting this question originally, I did some research on the problem in question, and it turns out that this is extremely easily fixable via replacing the file "ExplorerFrame.DLL" which is located in the System32 and SystemWOW64 Folders, in the windows folder, on the C:\ drive. As I quite frequently customize my computer, this is a normal thing for me to do and I know exactly how to safely and properly replace this file. The only problem is that I cannot for the life of me find a download of this file that actually works with my computer. I tried a couple from some different sites but they all caused explorer to not restart (I was given an error when starting the application from Task Manager) and was forced to revert to the broken .DLL files. Since there are 2 separate "ExplorerFrame.DLL" files; one for 64 bit and the other for 32 bit, I am assuming that I will need to download 2 separate versions to replace the corrupted ones. Where can I acquire these files? I am currently running Windows 7 Professional x64 Bit.

  Read the article

• How to connect FreeBSD Jail to network

  - by jgtumusiime

  So recently I successfully installed and configured a freebsd jail and I would like to install software within my jail but I cannot connect to the network. I'm trying to setup an apache+php+mysql installation within the jail and have the webserver accessible by users. Here is my rc.conf for the jail. ... jail_enable="YES" # Set to NO to disable starting of any jails jail_list="mambo2" # Space separated list of names of jails jail_mambo2_rootdir="/usr/jails/j01" # jail's root directory jail_mambo2_hostname="mambo2.ug" # jail's hostname jail_mambo2_ip="192.168.100.174" # jail's IP address jail_mambo2_devfs_enable="YES" # mount devfs in the jail jail_mambo2_devfs_ruleset="mambo2_ruleset" # devfs ruleset to apply to jail here is my jail ifconfig output mambo2# ifconfig rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 00:c1:28:00:48:db media: Ethernet autoselect (100baseTX <full-duplex>) status: active plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> metric 0 mtu 1500 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 mambo2# It does not show the IP address I configured within /etc/rc.conf. But, when I list the running jails, it shows the right IP address. Here is a list of jails running [root@mambo /usr/home/jtumusiime]# jls JID IP Address Hostname Path 5 192.168.100.174 mambo2.ug /usr/jails/j01 I also created a /etc/resolv.conf for nameservers. This was not in existence so I'm not quite sure if it is necessary? mambo2# cat /etc/resolv.conf nameserver 192.168.100.251 nameserver 8.8.8.8 mambo2# my host has 4 ip addresses, 3 public and one private: 192.168.100.173 I tried creating a jail using ezjail and this does not work out. [root@mambo /usr/src]# ezjail-admin update -p -i Error: Cannot find your copy of the FreeBSD source tree in . Consider using 'ezjail-admin install' to create the base jail from an ftp server. [root@mambo /usr/src]# I have an updated copy of freebsd 7.1 source tree from SVN in /usr/src/ [root@mambo /usr/src]# svn info Path: . URL: http://svn.freebsd.org/base/release/7.1.0 Repository Root: http://svn.freebsd.org/base Repository UUID: ccf9f872-aa2e-dd11-9fc8-001c23d0bc1f Revision: 243371 Node Kind: directory Schedule: normal Last Changed Author: kensmith Last Changed Rev: 186660 Last Changed Date: 2009-01-01 01:57:14 +0300 (Thu, 01 Jan 2009) [root@mambo /usr/src]# and I did #make buildworld while building the first jail i.e mambo2 Here is an excerpt of ouput of ezjail-admin install ... 221 Goodbye. Trying 193.162.146.4... Connected to ftp.freebsd.org. 220 ftp.beastie.tdk.net FTP server (Version 6.00LS) ready. 331 Guest login ok, send your email address as password. 230 Guest login ok, access restrictions apply. Remote system type is UNIX. Using binary mode to transfer files. 200 Type set to I. 550 pub/FreeBSD-Archive/old-releases/i386/7.1-RELEASE/base: No such file or directory. 221 Goodbye. Could not fetch base from ftp.freebsd.org. Maybe your release (7.1-RELEASE) is specified incorrectly or the host ftp.freebsd.org does not provide that release build. Use the -r option to specify an existing release or the -h option to specify an alternative ftp server. Querying your ftp-server... The ftp server you specified (ftp.freebsd.org) seems to provide the following builds: Trying 193.162.146.4... total 10 drwxrwxr-x 13 1006 1006 512 Feb 20 2011 8.2-RELEASE drwxrwxr-x 13 1006 1006 512 Apr 10 2012 8.3-RELEASE lrwxr-xr-x 1 1006 1006 16 Jan 7 2012 9.0-RELEASE -> i386/9.0-RELEASE drwxrwxr-x 7 1006 1006 1024 Feb 19 2012 ISO-IMAGES -rw-rw-r-- 1 1006 1006 637 Nov 23 2005 README.TXT drwxrwxr-x 5 1006 1006 512 Nov 2 02:59 i386 I do not want to upgrade my freebsd installation. I have googled around; but all in vail. Thank you

  Read the article

• stunnel crashing

  - by Jay

  I'm trying to use stunnel to secure a legacy application's communications. I can't seem to get it setup and working. Can anyone provide any hints where I'm going wrong? Here's what I'm trying to accomplish: A windows service on a client machine connects to a server on port 7000 using TCP. I'd like to encrypt the communication between client and server. Here's what I've tried: Created a new server that accepts ssl connections on port 7443. Got a certificate for the server and installed it. That seems to work with my test setup. Installed stunnel on my windows machine (version 7.43 from the distribution archive file). Installed libssl32.dll and libeay32.dll in the same directory as stunnel.exe ( from the openssl-0.9.8h-1 binary distribution). Installed it as a service using "stunnel -install" Configured stunnel as follows: debug=7 output=C:\p4\internal\Utility\Proxy\proxy.log service=Proxy taskbar=no [exchange] accept=7000 client=yes connect=proxy.blah.com:7443 I changed my hosts file to trick the old application into connecting through stunnel: server.blah.com 127.0.0.1 # when client looks up server it goes to stunnel proxy.blah.com IP-address-of-server.blah.com # stunnel connects to new server "server.blah.com" now resolves to the machine it's running on (i.e. stunnel). "proxy.blah.com" goes to the real server. stunnel should connect to the server. I start the stunnel service and try to connect. It looks like it's working but the stunnel service just shuts down with no message. 2010.04.19 13:16:21 LOG5[4924:3716]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:16:21 LOG5[4924:3716]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange accepted connection from 127.0.0.1:4134 2010.04.19 13:16:49 LOG6[4924:3748]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange connected remote server from x.253.120.19:4135 2010.04.19 13:20:24 LOG5[3668:3856]: Reading configuration from file stunnel.conf 2010.04.19 13:20:24 LOG7[3668:3856]: Snagged 64 random bytes from C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: Wrote 1024 new random bytes to C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: RAND_status claims sufficient entropy for the PRNG 2010.04.19 13:20:24 LOG7[3668:3856]: PRNG seeded successfully 2010.04.19 13:20:24 LOG7[3668:3856]: SSL context initialized for service exchange 2010.04.19 13:20:24 LOG5[3668:3856]: Configuration successful 2010.04.19 13:20:24 LOG5[3668:3856]: No limit detected for the number of clients 2010.04.19 13:20:24 LOG7[3668:3856]: FD=312 in non-blocking mode 2010.04.19 13:20:24 LOG7[3668:3856]: Option SO_REUSEADDR set on accept socket 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange bound to 0.0.0.0:7000 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange opened FD=312 2010.04.19 13:20:24 LOG5[3668:3856]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:20:24 LOG5[3668:3856]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:21:02 LOG7[3668:4556]: Service exchange accepted FD=372 from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:4556]: Creating a new thread 2010.04.19 13:21:02 LOG7[3668:4556]: New thread created 2010.04.19 13:21:02 LOG7[3668:3756]: Service exchange started 2010.04.19 13:21:02 LOG7[3668:3756]: FD=372 in non-blocking mode 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange accepted connection from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:3756]: FD=396 in non-blocking mode 2010.04.19 13:21:02 LOG6[3668:3756]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:21:02 LOG7[3668:3756]: connect_blocking: s_poll_wait x.80.60.32:7443: waiting 10 seconds 2010.04.19 13:21:02 LOG5[3668:3756]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange connected remote server from x.253.120.19:4157 2010.04.19 13:21:02 LOG7[3668:3756]: Remote FD=396 initialized 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): before/connect initialization 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server certificate A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server done A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client key exchange A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write change cipher spec A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write finished A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 flush data 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read finished A The client thinks the connection is closed: No connection could be made because the target machine actively refused it 127.0.0.1:7000 at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress) at System.Net.Sockets.Socket.Connect(EndPoint remoteEP) at Service.ConnUtility.Connect() Any suggestions?

  Read the article

• VMware vSphere cluster design for site redundancy

  - by Stefan Radovanovici

  I have a question about the best design for site redudancy when using vSphere clusters. A bit of background info about our situation first though. We are a medium-sized company with two main offices, located in different countries. Our networks are linked by a Layer2 150Mbps leased line which is currently underused. We have a variety of services running for internal use within the company, some on physycal servers and some on existing vSphere clusters. In our department we also run several services (almost all running under various forms of Linux) like NTP, Syslog, jump servers, monitoring servers and so on. We have now the requirement that those servers need to be redundant within each location (which they are not at the moment) and also site redudant (which they are to some extent, the servers are duplicated in the 2nd location with configurations kept in sync via various methods at the application layer). There is no SAN available for us, at least not something that we can use at the moment. Cost is also an issue. While we do have some budget available for this, we can't afford to buy SANs for both locations for example. I looked at the VSA feature and it seems that this could be something for us but I am unsure how to solve the site-redudancy requirement. At the moment for testing purposes I am setting up in a lab a vSphere 5 with VSA on two ESXi hosts. I am currently using the Essentials Plus kit with VSA license, which allows me to build a VSA cluster on up to 3 hosts, together with a vCenter license to manage them. The hosts each have two dual-port network cards and two 600GB drives, running in Raid1. Hardware-wise this will be enough for us to run the all the services we need as VMs and will provide redundandcy within the site. At the moment I see only two option to have site redundancy: build an identical VSA cluter in the second location and keep the various services sync'ed at application layer (database sync, rsync and so on). simply move one of the hosts from the existing cluster to the second location, basically having the VSA cluster span the 150Mbps link between the sites. I would very much prefer the second option but I am unsure how well it'll work, if it can work at all. Technically it should, we can span the needed VLANs across the leased line and have them available in the second location. The advantage would be that we don't need to worry at all about sync'ing databases and the like. But I have the feeling that the bandwidth will not be enough, I have no way of knowing how much traffic will the VSA cluster generate between the hosts. I realize that this will most likely depend on the individual usage of the VMs but still, I have no idea how VSA replicates data between the ESXi hosts. Are these my only options or can my goals be achieved in some other way ? Is there perhaps a way to have some sort of "cold stand by" cluster in the second location where the VMs would be sync'ed once per night from the main location ? The idea is that in case the first site becomes unavailable, we would be able to bring all those VMs online there. We would be ok with the data being 1 day old. Any answers are appreciated. Best regards, Stefan

  Read the article

• Computer not POSTing "randomly"?

  - by smoth190

  I have a custom built PC that is exhibiting some...odd... behavior, something I've never seen before. It was working fine one day, and the next day, it wouldn't start. Seeing as I wanted an upgrade anyway, I purchased a new motherboard that was compatible with all my parts. While replacing the motherboard, I accidentally damaged the CPU. Well, I wanted a new one anyway... so I got a new one. Seeing as I was replacing a ton of parts already, I bought a new PSU because the old one was super loud. When I slapped it all together, it starts up, lights, fans, drives, they all start. But I get no display from the monitor. No beeps, which I believe means it doesn't POST. I figured it was the RAM, because after removing the sound card and graphics card, there was nothing else that I hadn't replaced. When I remove both sticks of RAM, I get a continuous beeping, and according to the mobo handbook, means no RAM. So I think the mobo is functional, or atleast partly. I bought new RAM, but it still didn't work. I tried 3 monitors, with both VGA and DIV. So it's probably not the monitor, either. Now, let me get to the random part. Every 20 or so boots (I should also mention, for about 3 out of 5 boots I have to unplug the PC because it won't powerdown via the button), it will POST and I'll get display. Then, after about 2 or 3 resets, it won't work again. This confuses me so much, because even when I change nothing, it will/will not work. My thought is that maybe it has something to do with the RAM not clearing or something. I also reset the CMOS battery, incase that had anything to do with it, but no eval. I found some weird suggestion online about holding the power button for 30 seconds while it was unplugged. That did nothing, but I didn't expect it would... I've replaced just about the entire computer, and all the parts are compatible. Done about everything I can think of, but nothing has worked. Hopefully someone can help me here. And as I side note: When I do get my computer to boot, it says my hardware has changed and I have to re-activate windows. But it says I have to call Microsoft to do it. So I get this fancy automated voice that asks me to enter in a code into windows, then it asks me "How many computers have you activated with this copy of Windows?". Well, I had it on my computer before I replaced everything, so I said 1. Then he yelled at me for violating my 1-use license. I dunno what's going on there, do I have to re-purchase Windows 7? And they wonder why people pirate software... That's just a bonus question, though. Specs: 8GB of DDR2 RAM (Corsair) AMD CPU (I don't know what GHz or model because I can't find the box... (I think its 4 cores of 2.8Ghz) ASRock A785GM-LE Motherboard

  Read the article

• libvirt upgrade caused vms to not see drives (boot media not found)

  - by bias

  I upgraded to Ubuntu 12.04.1 and now libvirt (via open nebula) successfully runs vms but they aren't finding the 2 drives (specifically, the boot drive). One is "hd" the other is "cdrom". The machine boots but fails and displays something like "boot media not found hd" (this was in a vnc terminal and I didn't copy the output anywhere so that's not the verbatim message). I tried constructing a new disk using the new version of qemu (via vmbuilder) and this new machine has the same problem as the old machine. In case it matters (I can't see why it would) I'm using open nebula to manage the machines. There's nothing relevant in any of the logs: syslog, libvirtd, oned. Which is to say nothing interesting/anomalous is reported when the machine is brought up. Versions libvirt 0.9.8-2ubuntu17.4 qemu-kvm 1.0+noroms-0ubuntu14.3 The libvirt xml config portions (relavent) <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> ... <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='qcow2'/> <source file='/var/lib/one//203/images/disk.0'/> <target dev='sda' bus='scsi'/> <alias name='scsi0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/var/lib/one//203/images/disk.1'/> <target dev='sdc' bus='scsi'/> <readonly/> <alias name='scsi0-0-2'/> <address type='drive' controller='0' bus='0' unit='2'/> </disk> <controller type='scsi' index='0'> <alias name='scsi0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </controller> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </memballoon> ... </devices> The libvirt/qemu log contains 2012-11-25 22:19:24.328+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 256 -smp 1,sockets=1,cores=1,threads=1 -name one-204 -uuid 4be6c276-19e8-bdc2-e9c9-9ca5352f2be3 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/one-204.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -device lsi,id=scsi0,bus=pci.0,addr=0x5 -drive file=/var/lib/one//204/images/disk.0,if=none,id=drive-scsi0-0-0,format=qcow2 -device scsi-disk,bus=scsi0.0,scsi-id=0,drive=drive-scsi0-0-0,id=scsi0-0-0,bootindex=1 -drive file=/var/lib/one//204/images/disk.1,if=none,media=cdrom,id=drive-scsi0-0-2,readonly=on,format=raw -device scsi-disk,bus=scsi0.0,scsi-id=2,drive=drive-scsi0-0-2,id=scsi0-0-2 -netdev tap,fd=18,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3 -netdev tap,fd=19,id=hostnet1 -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4 -usb -vnc 0.0.0.0:204 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x6 kvm: -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom" kvm: -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom"

  Read the article

• Set up lnux box for hosting a-z [apache mysql php ssl]

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure Virtualhosts for SSL, setting up a CA, setting up SFTP with openSSH, or anything else would be appreciated.

  Read the article

• Pairing Bluetooth device with PIN fails

  - by Pikaro

  I'm trying to pair my old BlackBerry 8310 to my Linux desktop (up-to-date Debian Sid, 3.15-10.dmz.1-liquorix-amd64) by using blueman and its associated tools. Scanning for the device works equally well for both sides; however, I am unable to pair the two once it comes to entering the PIN. If I scan from my PC, I have two options in blueman-manager regarding my phone: Directly selecting "pair", or selecting "setup". If I select "pair", nothing happens on my desktop, but the phone asks me to enter a PIN; if I do so, it reports that pairing has failed. During that, nothing is logged to the console. Selecting "setup" opens a configuration dialog that allows for entering or generating a PIN. Regardless, I get to a screen that tells me to enter the PIN on the phone, and at the same time, the phone pops up the equivalent dialog. This would be what one would expect to work; but whatever I enter (naturally, the same on both), both devices report that pairing has failed, and blueman-manager logs init_services (/usr/lib/python2.7/dist-packages/blueman/main/Device.py:73) Loading services org.bluez.Error.AuthenticationFailed: Authentication Failed If I instead try to pair from the phone, I cannot see any kind of reaction from my desktop - all I get is the equivalent "pairing failed" message from the BlackBerry after I entered a PIN in the dialog that pops up there. hcitool scan and hciconfig -a work without complaints, but I cannot find a way to try the pairing as a whole on the console since bluez-simple-agent seems to have been discontinued and this recommendation is everywhere on Google. hcitool cc as root opens the PIN dialog on the phone, then fails with "Input/Output error" once I enter it. The user is not permitted to execute this command. I also tried creating /usr/lib/bluetooth/<MAC>/pincodes to manually define a persistent PIN, which seems to have had no effect. The same goes for running the different commands as root, though I'm really confused about the internal structure of the Bluetooth subsystem now: They usually and inconsistently failed with Python or DBUS errors or just showed the same results. The only other Bluetooth device I have around are a pair of Creative speakers. Trying "setup" asks me to enter a key on them, which is impossible. If I try "pair", I'm asked for a PIN as I should, but no pairing takes place, and no errors appear on the console. (It just repeats their name a few times.) Interestingly, I tried that before writing my question, and nothing happened in terms of PIN questions, just like with the BlackBerry, which still shows no change. I don't think I actively changed anything since then. The BlackBerry can pair with and connect to the speakers, and everything goes as one would expect, so the problem is definitely with my desktop. So thus my questions: What is that PIN window generated by, and why does it seem to appear randomly? How can I find out what, exactly, fails after trying to add the speakers, as this may give me a clue? Is there any kind of complete log that concerns itself with Bluetooth? What data can I provide to make this more solvable?

  Read the article

• Nginx Multiple Domains

  - by showFocus

  I am trying to add a second virtual host to nginx. When i go to the new domain it redirects to the old one. I have tried restarting Nginx, rebooting the server. Has anyone come across this before, care to share? File: nginx.conf ### user www-data www-data; worker_processes 4; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; tcp_nopush on; tcp_nodelay off; keepalive_timeout 5; gzip on; gzip_comp_level 2; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; include /usr/local/nginx/sites-enabled/*; } File: ../sites-enabled/domain1.co.uk server { listen 80; server_name www.domain1.co.uk; rewrite ^/(.*) http://domain1.co.uk/$1 permanent; } server { listen 80; server_name domain1.co.uk; access_log /home/me/public_html/domain1.co.uk/log/access.log; error_log /home/me/public_html/domain1.co.uk/log/error.log; location / { root /home/me/public_html/domain1.co.uk/public/; index index.php index.html; # WordPress supercache & permalinks. include /usr/local/nginx/conf/wordpress_params.super_cache; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include /usr/local/nginx/conf/fastcgi_params; fastcgi_param SCRIPT_FILENAME /home/me/public_html/domain1.co.uk/public/$fastcgi_script_name; } } File: ../sites-enabled/domain2.co.uk server { listen 80; server_name www.domain2.co.uk; rewrite ^/(.*) http://domain2.co.uk/$1 permanent; } server { listen 80; server_name domain2.co.uk; access_log /home/me/public_html/domain2.co.uk/log/access.log; error_log /home/me/public_html/domain2.co.uk/log/error.log; location / { root /home/me/public_html/domain2.co.uk/public/; index index.php index.html; # Basic version of WordPress parameters, supporting nice permalinks. # include /usr/local/nginx/conf/wordpress_params.regular; # Advanced version of WordPress parameters supporting nice permalinks and WP Super Cache plugin include /usr/local/nginx/conf/wordpress_params.super_cache; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include /usr/local/nginx/conf/fastcgi_params; fastcgi_param SCRIPT_FILENAME /home/me/public_html/domain2/public/$fastcgi_script_name; } }

  Read the article

• Configuring a PIX 506e for Asterisk

  - by orthogonal3

  Hi all! I'm having problems configuring a old Cisco PIX running 6.3 and wondered if anyone can lend a hand? Simply put I have a PIX 506e that I want to put in my VoIP data path. I can't update it and getting a compat version of Java for that version of PIX is tough so I can't log onto the web interface. The PIX straddles two networks..... 192.168.5.0 on the inside, ...50.0 on the outside both net masks are 255.255.255.0 I have a local Asterisk server cluster with a single service IP (<local asterisk>) SIP is on UDP 5060 and RTP (for the voip data) is on UDP 18000-18999 I know thats a big range but hey may as well. I need the 192.168.5.0 net to have web and ftp access for updates and the like. DHCP, DNS and NTP is already provided on that network so I don't need external DNS access. So I think I want the following rules: SIP or RTP from <my itsp> arriving at <outside voip ip> NATed to <local asterisk> SIP or RTP able to do the reverse route (should be covered by high sec - low sec??) HTTP and FTP access outbound for software update for the servers etc I have the following config at the minute - and I think I'm almost there (I hope)... interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password wouldyouliketobeapeppertoo encrypted passwd wouldyouliketobeapeppertoo encrypted hostname afirewall domain-name adomain fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 access-list acl_ping permit icmp any any access-list voip permit ip host <my itsp> host <local asterisk> mtu outside 1500 mtu inside 1500 ip address outside <outside pix ip> 255.255.255.0 ip address inside <inside pix ip> 255.255.255.0 arp timeout 14400 global (outside) 1 <outside generic ip> nat (inside) 1 192.168.5.0 255.255.255.0 0 0 static (inside,outside) <outside voip ip> <local asterisk> netmask 255.255.255.255 0 0 static (outside,inside) <local asterisk> <outside voip ip> netmask 255.255.255.255 0 0 access-group acl_ping in interface outside access-group acl_ping in interface inside route outside 0.0.0.0 0.0.0.0 <my next hop router> 1 route outside <my itsp> 255.255.255.255 <my next hop router> 1 I think I just need a hand with the access-lists and NAT/static rules. Would anyone be able to help as I've RTFM'd the Cisco docs a few times and they're heavy. Wishing I'd completed my CCNA now! Thanks all for any help, Phil

  Read the article

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

  Read the article

< Previous Page | 461 462 463 464 465 466 467 468 469 470 471 472  | Next Page >