Search Results

Search found 16499 results on 660 pages for 'off rhoden'.

Page 467/660 | < Previous Page | 463 464 465 466 467 468 469 470 471 472 473 474  | Next Page >

  • Cooling for a small server room

    - by John Zwinck
    I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

    Read the article

  • How to set the VirtualDocumentRoot based on the files within

    - by Chuck Vose
    I'm trying to set up Apache to use the VirtualDocumentRoot directive but my sites aren't all exactly the same. Most of the sites have a drupal folder which should be the root but there are a few really old drupal sites, a few rails sites, some django sites, etc. that want the Document root to be / or some other folder. Is there a way to set up VirtualDocumentRoot based on a conditional or is there a way to use RewriteRule/Cond to detect that / is the incorrect folder if there is a drupal folder or a public folder? Here's what I have so far: <VirtualHost *:80> # Wildcard ServerAlias, this is the default vhost if no specific vhost matches first. ServerAlias *.unicorn.devserver.com # Automatic ServerName, based on the HTTP_HOST header. UseCanonicalName Off # Automatic DocumentRoot. This uses the 4th level domain name as the document root, # for example http://bar.foo.baz.com/ would respond with /Users/vosechu/Sites/bar/drupal. VirtualDocumentRoot /Users/vosechu/Sites/%-4/drupal </VirtualHost> Thanks in advance! -Chuck

    Read the article

  • How to find out which program a default beep is coming from in Windows 7?

    - by leeand00
    There's a "default beep" (as defined in System Sounds) that emanates from my computer every so often. It kind of goes like this (where each number is a "default beep" sound): 1, 2, 3, 4, 5. So there's a distinct pattern to it. I thought I had this figured out a way to figure out what was happening by going to Control Panel-Ease of Access-Ease of Access Center-Replace sounds with visual cues But that just isn't the case. Whichever window I click on, that one displays the visual queue when this happens. It's driving me crazy, and I can't figure out which program is causing this. Update: it appears to only happen on one user profile on the computer...does that help? Update 2: Discovered that this sound was coming from a utility on my laptop called ASUS NB Probe; I'm certain that it is emanating from this program because the error message displayed by it changes in sync with the sound playing. Apparently the S.M.A.R.T. feature of my hard drive was reporting an issue. It displays the issue for a brief second and then makes it disappear, I'll have to keep watching it to see what it says, but I believe is says something about a read. I have an external hdd connected with eSATA to a container of sorts (BlacX) that you can plug two hdds into. I have one hdd attached and it's a Western Digital WD1001FALS - 00E8B0 Thanks again! Now I'm off to go around the Internet and report on this...since I posted it so many places!

    Read the article

  • windows 2003 under Hyper-V - can't send/receive ping

    - by glaucon
    I've installed Windows 2003 x64 R2 SP2 under Hyper-V (the Windows Pro 8 edition). I have a NIC configured but I can't move any traffic on it. In particular I can't send or receive Pings. Scoreboard There is a second VM running Ubuntu under the Windows 8 host which is able to send and receive pings from the host O/S . When I try to ping from Windows 2003 guest to Windows 8 host I get 'Request Timed Out'. When I try to ping from Windows 8 host to Windows 2003 guest I get 'Reply from 192.168.10.107 Destination Host Unreachable'. There's no problem pinging from the Ubuntu guest to the Windows 8 host and no problem pinging from the Windows 8 host to the Unbuntu guest. Environment Integration services are installed on Windows 2003. The windows 2003 needs a static IP address of 192.168.10.15. The Windows 2003 ipconfig output looks like this : While the host o/s ipconfig output looks like this : Event Logs The only things I can see in the event logs which is (a) looks signifcant and (b) is not related to the lack of networking is this : I'm not sure if that's significant or not. Hyper-V and NICs When the Windows 2003 guest was first booted it had no NIC; I subsequently added a 'Legacy Network Connector' which I couldn't get Windows 2003 to recognise; I subsequently removed that and added a 'Standard Network Connector' and at least on the surface this works ... only it doesn't. 'Virtual Network Type' is external. Although I've only mentioned ping there's no other evidence of network activity. 'Allow incoming echo request' is enabled on the Windows 2003 guest. HELP ? What else should I look at or do to resolve this problem ? EDIT 1: I should have said that I turned off the firewall on the W2003 server for a while and retested the pings; same result.

    Read the article

  • 500 error with deploying rails application via apache2+passenger

    - by user1633983
    I finally completed my own app, so the only work left is deploying the app. I'm using Ubuntu 10.04 and apache2(installed by apt-get), so I'm trying to deploy through passenger. I installed passenger gem like this: sudo gem install passenger rvmsudo passenger-install-apache2-module and I configured apache settings as what the installation message says. I added below lines in the middle of /etc/apache2/apache2.conf file. LoadModule passenger_module /home/admin/.rvm/gems/ruby-1.9.3-p194/gems/passenger-3.0.17/ext/apache2/mod_passenger.so PassengerRoot /home/admin/.rvm/gems/ruby-1.9.3-p194/gems/passenger-3.0.17 PassengerRuby /home/admin/.rvm/wrappers/ruby-1.9.3-p194/ruby and, I appended below lines in /etc/apache2/sites-available/default file. <VirtualHost *:80> ServerName localhost # !!! Be sure to point DocumentRoot to 'public'! DocumentRoot /home/admin/homepage/public <Directory /home/admin/homepage/public> # This relaxes Apache security settings. AllowOverride all # MultiViews must be turned off. Options -MultiViews </Directory> But when I restart the apache service and hit the address, 500 error occurs. At first, it was same 500 error but the 500 error page is from apache's, but when I reinstalled the libapache2-module-passenger, the 500 error page is changed to that from rails'. Because of rails' 500 error page(which is located at public/500.html), I think passenger module is properly connected with apache. What should I do to fix this problem? Do I need to configure something inside my app before deployment?

    Read the article

  • Lenvo B450 won't boot on battery only?

    - by Mywiki Witwiki
    We bought a Lenovo B450 laptop almost a year ago. It comes with a NVIDIA GEFORCE with CUDA graphics and so the battery life is terrible. It will only last 1:30 hours max. We try to run it on battery as much as possible but because the battery life is short sometimes we can't notice that the battery is so low until the computer blacks out. Because of the short battery life, the laptop is always plugged on AC power. One night the computer froze. Because it was already late, I just reset the laptop my pressing the power button for 10 seconds. The laptop shut off but I did not bother restarting it. The next morning, the laptop won't turn on on battery only. It will only turn on on AC power. The computer instantly shuts down(improperly) once the adapter is removed. But the battery was at 100% then. Now it is slowly losing charge (currently at 74%). The battery indicator says, "Plugged in, not charging". I want to bring the laptop to school but I can't because it won't be portable at all. Just to summarize it all: 1) The laptop suffered some blackouts already. 2) The laptop was on AC power most of the time. 3) When the computer froze, it was reset (hard shutdown). 4) The laptop won't boot with battery only since then. 5) The laptop will shutdown instantly when AC adapter is removed. 6) The battery won't charge and is gradually losing charge. ======================= UPDATE ============================= We got the battery replaced. Unfortunately, it delivers only 2 hours max of power.

    Read the article

  • OSX Server 10.5 - Cannot log into Workgroup Manager - diradmin password is correct

    - by Mister IT Guru
    I've got a setup where I am trying to rescue a broken AD. We can no longer authenticate on the Workgroup manager, with passwords being rejected all the time - even though it is correct. I can connect using the workgroup manager on another server and I get the user list as expected, but when I click the padlock to make changes, I get the following screen: The problem is, I know the password is correct, I just used it to connect to the server in the first place. I can log into the server using the local admin, and services such as AFP, VPN and SMB continue to serve users. I have about 300 or so users on this server, and I would very much like to avoid having a rebuild. As there is much configuration that has been done without my knowledge (it's a client machine), I'd like to attempt to fix it, and then create another server and migration OD off this broken machine, then decommission it "gently". Ultimately this would mean no disruption of services. What I'd like it some tips as to how to fix the problem with authenticating to make changes in the work group manager, and maintenance on open directory in general. Thanks

    Read the article

  • Deploying workstations - best practices?

    - by V. Romanov
    Hi guys I've been researching on the subject of workstation deployment for a while, and found a ton of info and dozens different methods and tools, but no "best practice" method that doesn't lack at least one feature that i consider required for the solution to be perfect. I'm currently interested in windows workstation deployment, but if the tools can be extended to Linux, then it's an added value. I want the deployment tools I use to be able to do the following: hardware independent - I want my image or installation to have a minimum of hardware and driver dependency, so that i can use a single image/package for all workstations easily updatable - I want to be able to update my image as easily as possible without redeploying/rebuilding/reimaging all configurations PXE bootable deployment - I want the tools to be bootable off the network so that I don't need a boot cd/DOK. scriptable for minimum human input - Ideally, the tool should run automatically after being booted and perform a "default" deployment (including partitioning) unless prompted otherwise. i.e - take a pc, hook it up, power on, PXE boot and forget about it until the OS is deployed. I found no single product or environment that does all this. Closest i came to is the windows deployment services/WIM image format. I also checked out numerous imaging and deployment tools including clonezilla, ghost, g4u, wpkg and others, but most of them lack the hardware Independence and updatability features. We currently have a Symantec Ghost server setup that does imaging over the network, but I'm not satisfied with it as it has all the drawbacks i listed above. Do you have suggestions how to optimize the process of workstation deployment? How do you deploy them in your organization? Thanks! Vadim.

    Read the article

  • How to change controller numbering/enumeration in Solaris 10?

    - by Jim
    After moving a Solaris 10 server to a new machine, the rpool disk is now c1t0d0. We have some third party applications hard coded for c0t0d0. How can I change the controller enumeration on this machine? There is no longer a c0. I've tried rebuilding the /etc/path_to_inst, but the instance numbers don't seem to match up with the controller numbers. Also, it's not clear if i86pc platforms use this file. I've tried devfsadm -C to clear the dangling links, but I'm not sure how to cause devfsadm to start numbering from 0 again (or force certain devices in the tree to a specific controller number). Next I am going to try to create the symlinks manually in /dev/dsk and rdsk to point to the correct /devices. I feel like I am going way off path here. Any suggestions? Thanks Update: This is on virtual ESXi hardware with an additional pass-through HBA. There is no controller 0 on the machine, that is for sure. devfsadm -C cleans up all the c0 device symlinks but keeps the already linked controllers at their current ids.

    Read the article

  • No digital audio output with Asus Xonar DG

    - by Lunatik
    I've purchased an Asus Xonar DG as replacement for faulty onboard audio in a Medion 8822 as it has an optical output which is all I really need to feed my HTPC. I uninstalled the previous drivers/devices, switched the PC off, inserted the Asus card, powered up, disabled the onboard audio in the BIOS, then installed the driver that came on the CD (same version as on Asus' website as of today) and everything went perfectly - no errors. I set the audio devices up in Windows and in the Asus utility (SPDIF enabled, 6-ch audio) as I would expect to see them work, but the only thing is I have no digital audio from test tones within Windows/the Asus utility, PCM audio or Dolby Digital from DVD. Analogue audio is fine. I've uninstalled things and reinstalled a couple of times now, as well as trying almost all combinations of analogue/digital outputs but can't get it sorted. Does anyone have any tips on how to get this working? This card has just been released so there isn't much out there to go on. Notes: The light on the toslink port is lit. OS is Vista 32-bit SP2 and all up to date, pretty much a fresh install with almost no 3rd party applications installed This page seems to suggest that a digital output device in Windows is not needed with Xonar cards as it was with the previous Realtek so I have it set to Analog. The only other output device is S/PDIF pass-thru

    Read the article

  • FastCGI and Apache 500 error intermittently

    - by benkorn1
    Hello, I have a FastCGI (mod_fastcgi)problem. It happens every once in a while, and does not casue a complete server meltdown, just 500 errors. Here are a couple things. First I am using APC so PHP is in control of it's own processes, not FastCGI. Also, I have the webroot set as: /var/www/html And the fcgi-bin inside: /var/www/html/fcgi-bin First off here is the apache error_log: [Fri Jan 07 10:22:39 2011] [error] [client 50.16.222.82] (4)Interrupted system call: FastCGI: comm with server "/var/www/html/fcgi-bin/php.fcgi" aborted: select() failed, referer: http://www.domain.com/ I also ran strace on the 'fcgi-pm' process. Here is a snip from the trace around the time it bombs out: 21725 gettimeofday({1294420603, 14360}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 6503 38*", 16384) = 46 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 96595}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 6154 23*C /var/www/html/fcgi-bin/php.fcgi - - 6483 28*", 16384) = 92 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 270744}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 5741 38*", 16384) = 46 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 311502}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 6064 32*", 16384) = 46 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 365598}, NULL) = 0 21725 read(14, "C /var/www/html/fcgi-bin/php.fcgi - - 6179 33*C /var/www/html/fcgi-bin/php.fcgi - - 5906 59*", 16384) = 92 21725 alarm(131) = 0 21725 select(15, [14], NULL, NULL, NULL) = 1 (in [14]) 21725 alarm(0) = 131 21725 gettimeofday({1294420603, 454405}, NULL) = 0 I noticed that the 'select()' seems to stay the same regardless, however the read() changes its return from 46 to some other number while it is bombing out. Has anyone seen anything like this. Could this be some sort of file locking? Thanks, Ben

    Read the article

  • Phusion Passenger (Apache, Sinatra) suddenly not working for a single site on my server

    - by Kerrick
    I've had Phusion Passenger working for a few of my sites for months. Then, today, it stopped working for a single site. I hadn't changed anything (I hadn't even SSH'ed into the server for a week), and everything is set up the way it should for it to work. Plus, it's working fine for other sites! I'm about to pull my hair out trying to find out what's wrong, so I was hoping y'all could help. Passenger is not working on kerricklong.com -- I only get the "It works!" Apache default page. If I look at the headers, it's not even serving the X-Powered-By: Phusion Passenger (mod_rails/mod_rack) header that I get on my other (currently working) Passenger-powered sites on the same server running Ubuntu Server 10.04. The following is in my /etc/apache2/sites-available/kerricklong.com file, but it's identical (with names and paths changed) to the configuration file for the site that is working. <VirtualHost *:80> ServerAdmin [email protected] ServerName kerricklong.com ServerAlias *.kerricklong.com DocumentRoot /redacted/path/to/kerricklong.com/public ErrorLog /redacted/path/to/kerricklong.com/logs/error.log <Directory /redacted/path/to/kerricklong.com/public> Allow from all Options -MultiViews Include /etc/apache2/h5bp.conf </Directory> php_flag engine off </VirtualHost> I've got the necessary tmp/, logs/, and public/ directories, along with config.ru. I've also run sudo a2dissite then sudo a2ensite, sudo service apache2 restart, and reboot the server to try to fix it. What gives?

    Read the article

  • Windows 7 hangs while loading desktop

    - by Joshua
    I am facing a weird problem. My computer hangs while loading the desktop, and only the background shows up; no icons or bars load. If I power the system on and off about 4-6 times, I may be able to use it normally. The desktop loads normally after rebooting or in safe mode; this only occurs when I start the system normally. I've tried several things to fix it, such as removing all start-up items, but it still doesn't solve the problem. What should I do? I found three major errors in Event Viewer: Source: Microsoft-Windows-DistributedCOM Level: Error DCOM got error "1084" attempting to start the service WSearch with arguments "" in order to run the server: {7D096C5F-AC08-4F1F-BEB7-5C22C517CE39} Source: Microsoft-Windows-DistributedCOM Level: Error DCOM got error "1084" attempting to start the service WSearch with arguments "" in order to run the server: {7D096C5F-AC08-4F1F-BEB7-5C22C517CE39} Source: Service Control Manager Level: Error The Network List Service service depends on the Network Location Awareness service which failed to start because of the following error: The dependency service or group failed to start.

    Read the article

  • Installing sqlite gem fails on AWS Linux instance with sqlite-devel libraries installed

    - by Scott
    Hi, I'm running an instance built off ami-595a0a1c. I am trying to install the sqlite3 (or sqlite) gem and it's failing with the below error: $ sudo gem install sqlite3 Building native extensions. This could take a while... ERROR: Error installing sqlite3: ERROR: Failed to build gem native extension. /usr/bin/ruby extconf.rb checking for sqlite3.h... no sqlite3.h is missing. Try 'port install sqlite3 +universal' or 'yum install sqlite3-devel' and check your shared library search path (the location where your sqlite3 shared library is located). extconf.rb failed * Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/usr/bin/ruby --with-sqlite3-dir --without-sqlite3-dir --with-sqlite3-include --without-sqlite3-include=${sqlite3-dir}/include --with-sqlite3-lib --without-sqlite3-lib=${sqlite3-dir}/lib Gem files will remain installed in /usr/lib64/ruby/gems/1.8/gems/sqlite3-1.3.3 for inspection. Results logged to /usr/lib64/ruby/gems/1.8/gems/sqlite3-1.3.3/ext/sqlite3/gem_make.out Typically, this just means you need to install the development libraries and everything is cool. However, I have installed the sqlite-devel packages and still no dice. Since this is the Amazon Linux instance, I'd rather not add more repositories than the ones Amazon provides if possible. What can i do to get this thing to compile? Thanks for any insight! From a brand new instance, here's what I've done: $ sudo yum install rubygems ruby-devel $ sudo gem update --system $ sudo gem install rails $ rails new app $ cd app $ rails server Could not find gem 'sqlite3 (= 0)' in any of the gem sources listed in your Gemfile. $ sudo yum install sqlite-devel $ sudo gem install sqlite (or sqlite3 -- same result) See breakage above

    Read the article

  • NFS headaches with FreeBSD 4.9

    - by Ernie
    Once upon a time, this used to work, and I kept the configuration the same, but... now nothing. I'm just trying to get an NFS server set up on a FreeBSD 4.9 server. The process should be about as complicated as this: Add this entry to /etc/exports: /var/home /var/vpopmail/domains -maproot=root XXX.XX.XX.XXX Execute this: portmap nfsd -u -t -n 4 mountd -r Then this should work, regardless of network and firewall issues: showmount -e localhost But showmount -e localhost fails with the following error: RPC: Port mapper failure showmount: can't do exports rpc And even if I kill off the NFS daemon, and try a rpcinfo -p localhost, I get this error: rpcinfo: can't contact portmapper: rpcinfo: RPC: Unable to receive; errno = Connection reset by peer The portmapper is still running. Why the heck does nothing work as if it isn't? Edit to add: FYI: Sockstat gives me this: $ sockstat |egrep "(nfsd|portmap)" root nfsd 86310 3 udp4 *:2049 *:* root nfsd 86310 4 udp4 *:973 *:* root portmap 45920 0 tcp4 *:111 *:* Then, at a later time (say, 5 minutes) it's as if nfsd isn't acting as a server: $ sockstat |egrep "(nfsd|portmap)" root portmap 45920 0 tcp4 *:111 *:* But the nfs daemon is still running: $ ps ax |grep nfsd 86311 ?? I 0:00.00 nfsd: server (nfsd) 86312 ?? I 0:00.00 nfsd: server (nfsd) 86313 ?? I 0:00.00 nfsd: server (nfsd) 86314 ?? I 0:00.00 nfsd: server (nfsd)

    Read the article

  • Finding cause of TCP retransmission within a LAN

    - by Surreal
    Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

    Read the article

  • Disable write-protection on Micro SD

    - by Tim
    My task today is to open up and copy some files to 700 brand new micro SD cards. As I get going on this task I am finding that some of the Micro SD cards are telling me "sorry this drive is write protected" To copy the files I am using a standard SD to micro SD card adapter, and a USB SD card reader / writer. I have ensured that the switch is set to OFF on all of my adapters. As soon as I get a Micro SD that tells me it is write protected I can use the same adapter with another micro SD and it works fine, so I know the problem is not with my adapters. My question is: How can I disable the write protection on a Micro SD card? This eHow article seems to indicate that there is also a physical switch on Micro SD cards. However I have personally never seen a Micro SD with a physical switch, and none of the ones I am using today have said switch. Since these cards are brand new and thus empty are the ones that are telling me they are write protected simply useless? Could this be caused by some sort of defect in the cards?

    Read the article

  • MySQL /G output

    - by conandor
    I ran mysql query as below on a non-partition table mysql> use test31 Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Database changed mysql> explain partitions SELECT * FROM my_friends WHERE (requestor = '1234567890' OR contact = '1234567890') AND status = 1 ORDER BY request_id DESC LIMIT 0,100\G *************************** 1. row *************************** id: 1 select_type: SIMPLE table: my_friends partitions: NULL type: index_merge possible_keys: friend_index,requestor,contact key: friend_index,contact key_len: 17,17 ref: NULL rows: 2 Extra: Using sort_union(friend_index,contact); Using where; Using filesort 1 row in set (0.00 sec) on a partition table mysql> explain partitions SELECT * FROM my_friends WHERE (requestor = '1234567890' OR contact = '1234567890') AND status = 1 ORDER BY request_id DESC LIMIT 0,100\G *************************** 1. row *************************** id: 1 select_type: SIMPLE table: my_friends partitions: p1_p1sp0,p1_p1sp1,p1_p1sp2,p1_p1sp3,p1_p1sp4,p1_p1sp5,p1_p1sp6,p1_p1sp7,p1_p1sp8,p1_p1sp9,p1_p1sp10,p1_p1sp11,p1_p1sp12,p1_p1sp13,p1_p1sp14,p1_p1sp15,p1_p1sp16,p1_p1sp17,p1_p1sp18,p1_p1sp19,p1_p1sp20,p1_p1sp21,p1_p1sp22,p1_p1sp23,p1_p1sp24,p1_p1sp25,p1_p1sp26,p1_p1sp27,p1_p1sp28,p1_p1sp29 type: index_merge possible_keys: friend_index,requestor,contact key: friend_index,contact key_len: 17,17 ref: NULL rows: 60 Extra: Using sort_union(friend_index,contact); Using where; Using filesort 1 row in set (0.01 sec) What does the "rows" mean? less rows is more faster query?

    Read the article

  • Need assistance making a batch file for renaming files in separate folders

    - by Carnaxus
    Ok, here's one for you. I'm trying to use a batch file to rename a bunch of files, but none of them are in the same folder as the batch file itself. The command prompt keeps telling me that the directory can't be found. I suppose I could just rename all the files in all the folders that match the filename, but I don't want to do that either; I only want to change certain ones. My batch file as it stands is: @echo off ren "engine/info.txt" "disabled.txt" ren "gravplating/info.txt" "disabled.txt" ren "HAWX content/info.txt" "disabled.txt" ren "laserz/info.txt" "disabled.txt" ren "NeuroNaval/info.txt" "disabled.txt" ren "NeuroPlanes/info.txt" "disabled.txt" ren "NeuroTanks/info.txt" "disabled.txt" ren "NeuroWeapons/info.txt" "disabled.txt" ren "WAC Base/info.txt" "disabled.txt" ren "WAC DamageSystem/info.txt" "disabled.txt" ren "WAC GravityController/info.txt" "disabled.txt" ren "WAC Helicopters/info.txt" "disabled.txt" ren "WAC Sweps/info.txt" "disabled.txt" ren "weapons/info.txt" "disabled.txt" ren "AFF_ships/info.txt" "disabled.txt" ren "AntiTakeRifle/info.txt" "disabled.txt" ren "Catmull-Rom Cameras/info.txt" "disabled.txt" ren "Displacer Cannon/info.txt" "disabled.txt" ren "Drumdevil's Trains/info.txt" "disabled.txt" ren "EVEOnline/info.txt" "disabled.txt" ren "gm_botmap_v3/info.txt" "disabled.txt" ren "gm_construct_flatgrass_v5-2/info.txt" "disabled.txt" ren "gm_mobenix_v3_final/info.txt" "disabled.txt" ren "gm_mobenix_v3_highquality_Water/info.txt" "disabled.txt" ren "gm_snabbansairfield_b1/info.txt" "disabled.txt" ren "gm_XhS_construct/info.txt" "disabled.txt" ren "linedraw/info.txt" "disabled.txt" ren "ModelManipulator/info.txt" "disabled.txt" ren "NeuroCars/info.txt" "disabled.txt" ren "Propeller Engine/info.txt" "disabled.txt" ren "VanDookie and Predaaator's pack/info.txt" "disabled.txt" ren "WAC ECM/info.txt" "disabled.txt" ren "WAC Extra Helicopters/info.txt" "disabled.txt" echo Done! pause

    Read the article

  • What does a status of "Backup" mean for Windows 7 local user profiles?

    - by Howiecamp
    Summary: Upon logging on to Windows 7 RTM I get a message that my profile can't be loaded and a temporary user profile is created. I logged off and back on as Administrator. The user profiles dialog shows my user profile with a Type of "Local" and a Status of "Backup" rather than "Local" which it should be. How can I change this to make my user profile accessible? The long story: My PC has a single hard drive partitioned into a C: and a D:. I'd moved my user profile directory (c:\Users) to d:\Users, removed c:\Users and then used mklink.exe to create a directory symbolic link c:\Users -- d:\Users. Worked like a charm since I did it. Today, I make a System Restore Point for drives C: and D:. Next, I dismounted D: and used the Disk Management tool to remove the "D:" drive letter from the D volume. (My plan was to reboot and then redirect the symbolic link.) Upon reboot, I got the user profile error described above. Finally, I restored the System Restore Points that I'd created for both drives and then rebooted again. Same issue.

    Read the article

  • EEE PC dropbox server running 24/7

    - by microspino
    I'd like to create a mini dropbox and print server on a small soho network of 5 users (all of them use windows XP desktops). The device need to run 24/7 or at least 12/7 (I can accept just workday hours too but the other two options would be better). Dropbox mini server: I mean I will have a 90gb dropbox on every computer on my network LAN syncing with It and the one onto It syncing to the web. Print Server: I have Samsung SCX 4521F (fax/print/scan/copy), Samsung ML2010, HP Laser jet P1006, HP Color Laserjet CP1215, HP Office jet pro K8600, HP Design jet 500. All of them now are connected using little print servers and I want to get rid of them hooking everything to this mini server. The fax/print/scan/copy machine need to stay connected to a PC to make me able to use the software that comes with It. The mini server would save me on this too. Fax/Scan server: since I have the above mentioned fax/print/scan/copy machine I would like to make people use It from/to their computers through the mini server. I thought to a recent EEEBOX machine because I heard good things about ATOM cpus and because It seems that a recent BIOS version could switch It off and on autonomously. I'd like to listen some advice from You. Best of all would be: If You have something similar running for a long time If You disagree with this hardware choice and If You would suggest some other device. If You see any issues with my printing setup Anything else ;) My budget is from Zero (using right sw to build something on top on a old PC) to 500€ max.

    Read the article

  • Windows 7 UAC (user access control) is being disabled on every reboot

    - by Christian Thamer
    To put it simply, I noticed UAC was disabled so I enabled it. I was prompted to reboot the computer for the changes to take effect. Upon my reboot I checked the settings again as I hadn't disabled UAC in the first place. It was again set to off (never notify). For the heck of it I repeated the process a couple of more times. Same result each time. I have Microsoft Security Essentials running a full scan nightly so I should be protected from viruses. I also did an on demand scan with the online tool at www.antivirus.com. Nothing was found. Other than the fact that UAC is being disabled on each reboot I have no other reason to suspect a virus. So my question is does anyone have insight into if this is a possible problem with a virus or other malware changing my UAC settings on each boot or is it possibly a problem with Windows and UAC itself? If it is malware are there suggestions for other products outside of the ones I have used to detect and remove it.

    Read the article

  • ProCurve 1800 switch issue

    - by user98651
    I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, every night when our Windows 2008 R2 server (off site) runs a backup to a iSCSI target (on site) [facilitated through a PPTP tunnel] the LAN loses connectivity with the router. To clarify, there is only one router which is connected to the switch affected by this problem. The only way to resolve the issue is to either reboot the router or pull the ethernet cable that goes to the router and plug it back in. During the outage, clients cannot receive DHCP requests, DNS requests, ping, or do anything else with the router in this state. Now, neither the switch or router are configured extensively and the issue only seems to have surfaced with the new switch in place. I have tried a number of things including replacing cables, rebooting and checking the switch configuration (it is literally as basic as you can get at this point-- flat LAN, no trunking). Interestingly, the router shows (accessed externally) no changes in configuration or status during this state but similarly cannot ping or access other hosts on the network. This issue occurs in different stages of backup (ie, different amounts transferred). I've also dumped packets from the switch into WireShark but cannot seem to find any anomaly yet (I'm looking at packets around the time the issue appeared and at the time when I reset the NIC). Any suggestions for what to look for? Ideas on what could be causing this? I'm seeing some transmit/receive errors on the NIC from both the router and switch side but nothing serious when compared to the total packet counts. I'm seriously doubting hardware at this point, as I have tried another switch, different cables, and a different NIC on the router.

    Read the article

  • Remote Desktop Printing With Color

    - by philibertperusse
    Our ACCPACC administration software runs on an off-site dedicated hosted computer, running Windows 2003 Server with a completely different NT DOMAIN. We have many users connecting to that computer remotely to perform administrative tasks such as printing cheques, printing invoices, printing POs, packing slips and so on. Basically the setup is that we are all connecting using Remote Desktop Protocol (local computers are Mac OS.X, XP SP3, Vista and Windows 7). At our office we have a DOCUCOLOR 242 printer. When printing from the ACCPACC software, it prints to the local printer in our office. This is because we are using RDP features to connect printer ressources to the remote computer. This almost works now. I had to install the printer driver software on the remote 2003 Server for the printer sharing to work. Now, everyone is able to print black and white but color is out. NOTES: Normal users on that Windows 2003 server are running as part of a Group Policy Object to restrict what can be done. I took one of these normal users and gave him all domain administrator rights, no effect still B&W only. I took this account and moved it OUT of GPO policies, as a normal account instead, no effect still B&W only. It seems only MY account (which is domain administrator AND a normal account not part of the GPO objects) can actually print with color. This is the account that was used for installing the printer driver software. How can I manage to get everyone to print in color? Any suggestions as to what to try next?

    Read the article

  • Unable to connect to CopSSH when running Windows service, works when running sshd directly

    - by Joe Enos
    I've been using CopSSH (that uses OpenSSH and Cygwin, so I don't know which of the three is the problem) as my SSH server application at home on Windows 7 Ultimate 32 bit. I have used it for about a year with no real problems, other than it sometimes takes 2 or 3 connection attempts to get through, but it's always worked within a few attempts. A few days ago, it just stopped working. The Windows service is still running, and I've rebooted, restarted the service, etc. with no change. On the client (using Putty on Windows), I get the message "Software caused connection abort". On the server, my event viewer registers the following: fatal: Write failed: Socket operation on non-socket I finally got it working, but only by executing sshd.exe directly from the command line on the server. No special flags or options, just straight execution, and then when I connect remotely, it goes through. I do have firewall and anti-virus software which appears to be configured properly, but the fact that things work when running sshd.exe also indicates that the firewall is fine. I thought the service and executable did exactly the same thing, but apparently there's some difference. Does anyone have any ideas on where I should look for the problem? If I can't find something, I suppose I can write a Windows service or scheduled task that fires off sshd.exe directly and ensures that it stays running, but that's kind of a last resort, since it's just wrapping around something that should already work. I appreciate your help.

    Read the article

< Previous Page | 463 464 465 466 467 468 469 470 471 472 473 474  | Next Page >