Search Results

Search found 21004 results on 841 pages for 'assembly load'.

Page 468/841 | < Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >

• NIC Bonding/balance-rr with Dell PowerConnect 5324

  - by Branden Martin

  I'm trying to get NIC bonding to work with balance-rr so that three NIC ports are combined, so that instead of getting 1 Gbps we get 3 Gbps. We are doing this on two servers connected to the same switch. However, we're only getting the speed of one physical link. We are using 1 Dell PowerConnect 5324, SW version 2.0.1.3, Boot version 1.0.2.02, HW version 00.00.02. Both servers are CentOS 5.9 (Final) running OnApp Hypervisor (CloudBoot) Server 1 is using ports g5-g7 in port-channel 1. Server 2 is using ports g9-g11 in port-channel 2. Switch show interface status Port Type Duplex Speed Neg ctrl State Pressure Mode -------- ------------ ------ ----- -------- ---- ----------- -------- ------- g1 1G-Copper -- -- -- -- Down -- -- g2 1G-Copper Full 1000 Enabled Off Up Disabled Off g3 1G-Copper -- -- -- -- Down -- -- g4 1G-Copper -- -- -- -- Down -- -- g5 1G-Copper Full 1000 Enabled Off Up Disabled Off g6 1G-Copper Full 1000 Enabled Off Up Disabled Off g7 1G-Copper Full 1000 Enabled Off Up Disabled On g8 1G-Copper Full 1000 Enabled Off Up Disabled Off g9 1G-Copper Full 1000 Enabled Off Up Disabled On g10 1G-Copper Full 1000 Enabled Off Up Disabled On g11 1G-Copper Full 1000 Enabled Off Up Disabled Off g12 1G-Copper Full 1000 Enabled Off Up Disabled On g13 1G-Copper -- -- -- -- Down -- -- g14 1G-Copper -- -- -- -- Down -- -- g15 1G-Copper -- -- -- -- Down -- -- g16 1G-Copper -- -- -- -- Down -- -- g17 1G-Copper -- -- -- -- Down -- -- g18 1G-Copper -- -- -- -- Down -- -- g19 1G-Copper -- -- -- -- Down -- -- g20 1G-Copper -- -- -- -- Down -- -- g21 1G-Combo-C -- -- -- -- Down -- -- g22 1G-Combo-C -- -- -- -- Down -- -- g23 1G-Combo-C -- -- -- -- Down -- -- g24 1G-Combo-C Full 100 Enabled Off Up Disabled On Flow Link Ch Type Duplex Speed Neg control State -------- ------- ------ ----- -------- ------- ----------- ch1 1G Full 1000 Enabled Off Up ch2 1G Full 1000 Enabled Off Up ch3 -- -- -- -- -- Not Present ch4 -- -- -- -- -- Not Present ch5 -- -- -- -- -- Not Present ch6 -- -- -- -- -- Not Present ch7 -- -- -- -- -- Not Present ch8 -- -- -- -- -- Not Present Server 1: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:55 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:28:ae USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:28:af USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.52.1 NETMASK=255.255.0.0 GATEWAY=10.200.2.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:55 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:ae Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:af Server 2: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:a7 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:30:30 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:30:31 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.53.1 NETMASK=255.255.0.0 GATEWAY=10.200.3.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:a7 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:30 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:31 Here are the results of iperf. ------------------------------------------------------------ Client connecting to 10.200.52.1, TCP port 5001 TCP window size: 27.7 KByte (default) ------------------------------------------------------------ [ 3] local 10.200.3.254 port 53766 connected with 10.200.52.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 950 MBytes 794 Mbits/sec

  Read the article

• Memcached Lagging

  - by Brad Dwyer

  Let me preface this by saying that this is a followup question to this topic. That was "solved" by switching from Solaris (SmartOS) to Ubuntu for the memcached server. Now we've multiplied load by about 5x and are running into problems again. We are running a site that is doing about 1000 requests/minute, each request hits Memcached with approximately 3 reads and 1 write. So load is approximately 65 requests per second. Total data in the cache is about 37M, and each key contains a very small amount of data (a JSON-encoded array of integers amounting to less than 1K). We have setup a benchmarking script on these pages and fed the data into StatsD for logging. The problem is that there are spikes where Memcached takes a very long time to respond. These do not appear to correlate with spikes in traffic. What could be causing these spikes? Why would memcached take over a second to reply? We just booted up a second server to put in the pool and it didn't make any noticeable difference in the frequency or severity of the spikes. This is the output of getStats() on the servers: Array ( [-----------] => Array ( [pid] => 1364 [uptime] => 3715684 [threads] => 4 [time] => 1336596719 [pointer_size] => 64 [rusage_user_seconds] => 7924 [rusage_user_microseconds] => 170000 [rusage_system_seconds] => 187214 [rusage_system_microseconds] => 190000 [curr_items] => 12578 [total_items] => 53516300 [limit_maxbytes] => 943718400 [curr_connections] => 14 [total_connections] => 72550117 [connection_structures] => 165 [bytes] => 2616068 [cmd_get] => 450388258 [cmd_set] => 53493365 [get_hits] => 450388258 [get_misses] => 2244297 [evictions] => 0 [bytes_read] => 2138744916 [bytes_written] => 745275216 [version] => 1.4.2 ) [-----------:11211] => Array ( [pid] => 8099 [uptime] => 4687 [threads] => 4 [time] => 1336596719 [pointer_size] => 64 [rusage_user_seconds] => 7 [rusage_user_microseconds] => 170000 [rusage_system_seconds] => 290 [rusage_system_microseconds] => 990000 [curr_items] => 2384 [total_items] => 225964 [limit_maxbytes] => 943718400 [curr_connections] => 7 [total_connections] => 588097 [connection_structures] => 91 [bytes] => 562641 [cmd_get] => 1012562 [cmd_set] => 225778 [get_hits] => 1012562 [get_misses] => 125161 [evictions] => 0 [bytes_read] => 91270698 [bytes_written] => 350071516 [version] => 1.4.2 ) ) Edit: Here is the result of a set and retrieve of 10,000 values. Normal: Stored 10000 values in 5.6118 seconds. Average: 0.0006 High: 0.1958 Low: 0.0003 Fetched 10000 values in 5.1215 seconds. Average: 0.0005 High: 0.0141 Low: 0.0003 When Spiking: Stored 10000 values in 16.5074 seconds. Average: 0.0017 High: 0.9288 Low: 0.0003 Fetched 10000 values in 19.8771 seconds. Average: 0.0020 High: 0.9478 Low: 0.0003

  Read the article

• Trying to build OpenSimulator.. nant fails

  - by Gary

  Output of nant is: Buildfile: file:///root/opensim-0.6.8-release/OpenSim.build Target framework: Mono 2.0 Profile Target(s) specified: build [echo] Using 'mono-2.0' Framework init: Debug: [echo] Platform unix build: [nant] /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build build Buildfile: file:///root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build Target framework: Mono 2.0 Profile Target(s) specified: build build: [echo] Build Directory is /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/bin/Debug [csc] Compiling 29 files to '/root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/bin/Debug/OpenSim.Framework.Servers.HttpServer.dll'. [csc] /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/AsynchronousRestObjectRequester.cs(103,41): error CS0246: The type or namespace name `TResponse' could not be found. Are you missing a using directive or an assembly reference? [csc] Compilation failed: 1 error(s), 0 warnings BUILD FAILED - 0 non-fatal error(s), 1 warning(s) /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build(14,6): External Program Failed: /usr/lib/pkgconfig/../../lib/mono/2.0/gmcs.exe (return code was 1) Total time: 1.2 seconds. BUILD FAILED Nested build failed. Refer to build log for exact reason. Total time: 1.3 seconds. OS is Fedora 7. Any ideas appreciated. :)

  Read the article

• cisco 2900xl - SNMP - Get mac address of device connected to an interface

  - by ankit

  Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

  Read the article

• Intermittent 404 on select assets, LAMP stack

  - by Tom Lagier

  We have a LAMP stack WordPress server that is serving most assets correctly. However, one plugin's CSS file and several images are returning soft 404s roughly 20% of the time. I can't find any reference to the 404 in the access logs, but the browser is definitely receiving a 404 response from somewhere (WordPress, I would assume). When I use an alias URL that does not match the site URL but does resolve to the asset path, the resource loads correctly 100% of the time. However, using the site url only resolves for the select, problematic assets 20% of the time. You can test one of the problematic assets here: http://www.mreco.org/wp-content/uploads/2014/05/zero-cost.jpg However the alias link always resolves correctly: http://mr-eco.wordpress.promocampaigns.com/wp-content/uploads/2014/05/zero-cost.jpg Stranger, if I attempt to access outdated content that definitely does not exist on the server, at the live URL it returns the content roughly 50% of the time. Using the alias link, it 404s 100% of the time - the correct behavior. Error log and PHP error log are clean. A sample access log (pulled from grep 'zero-cost.jpg' /var/log/httpd/mr-eco-access_log) from several refreshes of the live direct link (where I am not seeing any 404's): 10.166.202.202 - - [28/May/2014:20:27:41 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 304 - 10.166.202.202 - - [28/May/2014:20:27:42 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 304 - 10.166.202.202 - - [28/May/2014:20:27:43 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 304 - 10.166.202.202 - - [28/May/2014:20:27:43 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 304 - 10.176.201.37 - - [28/May/2014:20:27:56 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 200 57027 Chrome's dev tools list the following network activity before displaying 404 page content: zero-cost.jpg /wp-content/uploads/2014/05 GET 404 Not Found text/html Other 15.9?KB 73.2?KB 953?ms 947?ms My Apache configuration is standard, I've listed the virtual host entry and .htaccess file below. I can provide other parts of Apache config if necessary. Virtual host: <VirtualHost *:80> DocumentRoot /var/www/public_html/mr-eco.wordpress.promocampaigns.com ServerName www.mreco.org ServerAlias mreco.org mr-eco.wordpress.promocampaigns.com ErrorLog logs/mr-eco-error_log CustomLog logs/mr-eco-access_log common <Directory /var/www/public_html/mr-eco.wordpress.promocampaigns.com> AllowOverride All SetOutputFilter DEFLATE </Directory> </VirtualHost> .htaccess: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress I have checked for multiple A records and can confirm that there is a single A record pointing at the domain: ;; ANSWER SECTION: mreco.org. 60 IN A 50.18.58.174 I'm fairly new to systems administration, and at a complete loss as to what could cause this. In the past, inconsistently 404ing assets have been because of out-of-sync instances behind a load balancer. In this case, it is a single instance behind the load balancer. Because of the inconsistency, it feels like a caching issue. We don't make use of Apache caching, and as far as I know WordPress should not be caching either. What I've done so far: Reset WordPress permalinks Disabled WordPress plugins Re-generated WordPress .htaccess file Swapped ServerName and ServerAlias directives Cleared browser cache Confirmed disk location of resources Checked PHP, access, and error logs Confirmed correct DNS setup (can post if necessary) I'm at a total loss. Thanks for helping me out!

  Read the article

• What is the minimal steps to setup a client-server network using Windows Server 2008 R2 standard?

  - by Motivated Student

  Background I have One computer server with Win Server 2008 R2 standard installed but it has not been configured. This server has 2 LAN adapters. One adapter is connected to ISP and the other one connected to HUB/Switch. Other computers working as clients are connected to the same HUB/Switch to which the server is connected. IP Printers, IP scanners, IP camera are also connected to the same HUB/Switch. Note: I am a newbie. I only know how to plug RJ-45 sockets and assembly computer peripherals. I have no prior experience in Windows Server at all. Please teach me from the newbie's point of view. Objective I want to establish the following: Each client can access the internet, printers, scanners after it has been successfully authenticated by the server. Unauthenticated clients cannot access the internet, printers, etc. The server hosts a local site. Clients can browse internally using a private domain www.company.com. If the same domain name has been used by other on the internet, my private domain must override the public domain.

  Read the article

• Incorrect gzipping of http requests, can't find who's doing it

  - by Ned Batchelder

  We're seeing some very strange mangling of HTTP responses, and we can't figure out what is doing it. We have an app server handling JSON requests. Occasionally, the response is returned gzipped, but with incorrect headers that prevent the browser from interpreting it correctly. The problem is intermittent, and changes behavior over time. Yesterday morning it seemed to fail 50% of the time, and in fact, seemed tied to one of our two load-balanced servers. Later in the afternoon, it was failing only 20 times out of 1000, and didn't correlate with an app server. The two app servers are running Apache 2.2 with mod_wsgi and a Django app stack. They have identical Apache configs and source trees, and even identical packages installed on Red Hat. There's a hardware load balancer in front, I don't know the make or model. Akamai is also part of the food chain, though we removed Akamai and still had the problem. Here's a good request and response: * Connected to example.com (97.7.79.129) port 80 (#0) > POST /claim/ HTTP/1.1 > User-Agent: curl/7.19.7 (x86_64-pc-linux-gnu) libcurl/7.19.7 OpenSSL/0.9.8k zlib/1.2.3.3 libidn/1.15 > Host: example.com > Accept: */* > Referer: http://example.com/apps/ > Accept-Encoding: gzip,deflate > Content-Length: 29 > Content-Type: application/x-www-form-urlencoded > } [data not shown] < HTTP/1.1 200 OK < Server: Apache/2 < Content-Language: en-us < Content-Encoding: identity < Content-Length: 47 < Content-Type: application/x-javascript < Connection: keep-alive < Vary: Accept-Encoding < { [data not shown] * Connection #0 to host example.com left intact * Closing connection #0 {"msg": "", "status": "OK", "printer_name": ""} And here's a bad one: * Connected to example.com (97.7.79.129) port 80 (#0) > POST /claim/ HTTP/1.1 > User-Agent: curl/7.19.7 (x86_64-pc-linux-gnu) libcurl/7.19.7 OpenSSL/0.9.8k zlib/1.2.3.3 libidn/1.15 > Host: example.com > Accept: */* > Referer: http://example.com/apps/ > Accept-Encoding: gzip,deflate > Content-Length: 29 > Content-Type: application/x-www-form-urlencoded > } [data not shown] < HTTP/1.1 200 OK < Server: Apache/2 < Content-Language: en-us < Content-Encoding: identity < Content-Type: application/x-javascript < Content-Encoding: gzip < Content-Length: 59 < Connection: keep-alive < Vary: Accept-Encoding < X-N: S < { [data not shown] * Connection #0 to host example.com left intact * Closing connection #0 ?V?-NW?RPR?QP*.I,)-???A??????????T??Z? ??/ There are two things to notice about the bad response: It has two Content-Encoding headers, and the browsers seem to use the first. So they see an identity encoding header, and gzipped content, so they can't interpret the response. The bad response has an extra "X-N: S" header. Perhaps if I could find out what intermediary adds "X-N: S" headers to responses, I could track down the culprit...

  Read the article

• http request via iptables --to-destination ip redirect results in no response

  - by Wouter Vegter

  I have two Ubuntu servers with each having their own ip addresses. Let's call them server1 and server2, having respectively ip 1.1.1.1 and 2.2.2.2 I have a nginx running on server2. The sole purpose I want server1 to have is to redirect all incoming http (so port 80) requests to server2 without clients noticing that their request is being redirected. I tried the following command on server1: iptables -t nat -A PREROUTING -p tcp --dport 80 -j DNAT --to-destination 2.2.2.2 But when I enter 1.1.1.1 in my browser I get no respond: the page keeps trying to load without giving any message or error message (I get a time-out after 2-3 mins). But when I do remove the above iptables rule I immediately do get a "page not found error" when I enter 1.1.1.1 in my browser; so something is working but not as it should: when I enter 1.1.1.1 I want the html page to load that is hosted on 2.2.2.2 Because when i enter 2.2.2.2 in my browser I do see the webpage loaded. Could anyone please help me with this? I am searching quite some time (on severfault & Google) on this now so that's why I ask. Many thanks for reading my question! Update: Thank you all for you information. Unfortunately I still get no response I have the following iptables configuration: root@ip-10-48-238-216:/home/ubuntu# sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination root@ip-10-48-238-216:/home/ubuntu# sudo iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination DNAT tcp -- anywhere anywhere tcp dpt:www to:2.2.2.2 Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination When i run tcpdump and do request via chrome to 1.1.1.1 i get the following root@ip-10-48-238-216:/home/ubuntu# sudo tcpdump -i eth0 port 80 -vv tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 13:56:18.346625 IP (tos 0x0, ttl 52, id 12055, offset 0, flags [DF], proto TCP (6), length 60) 212-123-161-112.ip.telfort.nl.16386 ip-10-48-238-216.eu-west-1.compute.internal.www: Flags [S], cksum 0xb398 (correct), seq 2639758575, win 5840, options [mss 1460,sackOK,TS val 1223672 ecr 0,nop,wscale 6], length 0 13:56:18.346662 IP (tos 0x0, ttl 51, id 12055, offset 0, flags [DF], proto TCP (6), length 60) 212-123-161-112.ip.telfort.nl.16386 ww1dc1.shopreme.com.www: Flags [S], cksum 0x9ee0 (correct), seq 2639758575, win 5840, options [mss 1460,sackOK,TS val 1223672 ecr 0,nop,wscale 6], length 0 13:56:18.598747 IP (tos 0x0, ttl 52, id 10138, offset 0, flags [DF], proto TCP (6), length 60) 212-123-161-112.ip.telfort.nl.16387 ip-10-48-238-216.eu-west-1.compute.internal.www: Flags [S], cksum 0xac40 (correct), seq 2645658541, win 5840, options [mss 1460,sackOK,TS val 1223735 ecr 0,nop,wscale 6], length 0 13:56:18.598777 IP (tos 0x0, ttl 51, id 10138, offset 0, flags [DF], proto TCP (6), length 60) 212-123-161-112.ip.telfort.nl.16387 ww1dc1.shopreme.com.www: Flags [S], cksum 0x9788 (correct), seq 2645658541, win 5840, options [mss 1460,sackOK,TS val 1223735 ecr 0,nop,wscale 6], length 0 ^C 4 packets captured 4 packets received by filter 0 packets dropped by kernel the mentioned address relate to the following 212-123-161-112.ip.telfort.nl.16386 : my personal computer ww1dc1.shopreme.com.www : dns of server2 (2.2.2.2) ip-10-48-238-216.eu-west-1.compute.internal.www : amazon web services ec2 internal address of server1 (1.1.1.1) However, the tcpdump log on server2 (2.2.2.2) stays empty and I get no response back in my browser. I am able to ping from server1 to server2. And net.ipv4.ip_forward is set to 1 and so is /proc/sys/net/ipv4/ip_forward Could there be anything else that is missing?

  Read the article

• IBM Server Config questions

  - by Joel Coel

  I have a few questions on a potential server setup. First, the situation: Last year we bought an IBM x3500 server with 2 Xeon E5410's, 9GB RAM, 6 HDDs. The original intent for this server was to replace the old exchange e-mail server. It was brought in, set up, and then shortly after we switched to gmail. Shortly after that my predecessor left for greener pastures, and finally I was hired. So this nice server is now sitting (mostly) idle. This year I have budget again for one server, and of course I want to put this other server to work. I'm thinking about the best use for the two server, and I think I finally have a plan for what I want to do with them. The idea is to use the two newer servers as a pair of VM hosts. I will set up each server with the same 8 VMs, but divide up the load so that only 4 are active per physical host. That means I've normally got 2GB RAM + 2 cores per host. I've done some load testing to pick out what servers to convert to virtual, and chose them so that each host will be capable of handling the entire set of 8 by itself in a pinch with 1 core and 1GB RAM, but would be very taxed to do so. This should take our data center from 13 total servers down to 7. The "servers" I'm replacing are mostly re-purposed desktops, so I'm more than happy to be able to do this. Now it's time to go shopping for the new server. I'd like my two hosts to match as closely as possible, and so I'm looking at IBM again. It also helps that we have some educational matching grant money from IBM that I need to use to help pay for this system (we're a small private college). So finally, (if you're not bored already), we come to my questions: Am I missing anything big or obvious in this plan? I'm a little worried about network performance since the VM hosts will only have 4 nics total where 8 used to be, but I don't think it will be a problem. Is there anything else like this I might be overlooking? Am I making it even too complicated? IBM no longer has a good analog to last year's server. If I want to match the performance (8 cores, 9GB RAM, 1333mhz front side bus, 6 spindles), I have to spend quite a bit more than we paid last year: $2K+, or nearly a 33% cost increase. This only brings a marginal increase in performance. The alternative to stay in budget is to take a hit on the fsb down to 800mhz or cut the number of cores in half, neither of which is attractive. The main cost culprit is the processor. IBM no longer offers the E5410. It's listed as a part, but not available in any of the server configs I've looked at. I'm considering getting the cheapest 800mhz fsb dual core xeon I can configure and then buying the E5410's separately. That's still an extra $350 I wasn't counting on, but that's better than $2K. I want to know what others think of this - will it work or will I end up with the wrong motherboard or some other issue? Am I missing a simple way to configure the server I really want? I don't really intend to do this, but one option to save some money back is to omit the redundant power supply. Since my redundancy plan for these system is to switch over to a completely different host, the extra power isn't fully necessary. That said, it's still very helpful to avoid even short downtimes while I switch over VMs. Has anyone done this?

  Read the article

• IIS 6 + ASP.NET web service - DW20 and stackoverflow exception

  - by pcampbell

  Consider an ASP.NET SOAP web service that starts up fine, but craters hard when receiving its first hit. Please note that this is deployment works in the Test environment, but not in the PreProd environment. Both are Windows 2003 SP3 + IIS 6 + ASP.NET 3.5. All up-to-date. The behaviour that we're seeing is: restart the site & app pool the app pool is configured to run under Network Service. browsing to the .asmx and .wsdl responds normally, as expected. send a normal well-formed SOAP request / normal payload to the web service 100% CPU usage after 5 seconds, the page request / site returns "Service Unavailable" no entry is created in the IIS log file (i.e. c:\windows\system32\logfiles\W3C-foo) the app pool ends up being stopped The processes that hit the CPU hard are dw20.exe. I am unsure why Dr Watson is involved here. Event Log shows an ASP.NET Runtime error: Task Manager: Event log text: EventType clr20r3, P1 w3wp.exe, P2 6.0.3790.3959, P3 45d6968e, P4 errormanagement, P5 1.0.0.0, P6 4b86a13f, P7 24, P8 0, P9 system.stackoverflowexception, P10 NIL. Questions Any thoughts on what this system.stackoverflow exception might be? Given that the code is the same between environments, might it be a payload problem? Could it be a configuration issue? You can see the name of my .NET assembly there in the exception message: "ErrorManagement"

  Read the article

• Does this prove a network bandwidth bottleneck?

  - by Yuji Tomita

  I've incorrectly assumed that my internal AB testing means my server can handle 1k concurrency @3k hits per second. My theory at at the moment is that the network is the bottleneck. The server can't send enough data fast enough. External testing from blitz.io at 1k concurrency shows my hits/s capping off at 180, with pages taking longer and longer to respond as the server is only able to return 180 per second. I've served a blank file from nginx and benched it: it scales 1:1 with concurrency. Now to rule out IO / memcached bottlenecks (nginx normally pulls from memcached), I serve up a static version of the cached page from the filesystem. The results are very similar to my original test; I'm capped at around 180 RPS. Splitting the HTML page in half gives me double the RPS, so it's definitely limited by the size of the page. If I internally ApacheBench from the local server, I get consistent results of around 4k RPS on both the Full Page and the Half Page, at high transfer rates. Transfer rate: 62586.14 [Kbytes/sec] received If I AB from an external server, I get around 180RPS - same as the blitz.io results. How do I know it's not intentional throttling? If I benchmark from multiple external servers, all results become poor which leads me to believe the problem is in MY servers outbound traffic, not a download speed issue with my benchmarking servers / blitz.io. So I'm back to my conclusion that my server can't send data fast enough. Am I right? Are there other ways to interpret this data? Is the solution/optimization to set up multiple servers + load balancing that can each serve 180 hits per second? I'm quite new to server optimization, so I'd appreciate any confirmation interpreting this data. Outbound traffic Here's more information about the outbound bandwidth: The network graph shows a maximum output of 16 Mb/s: 16 megabits per second. Doesn't sound like much at all. Due to a suggestion about throttling, I looked into this and found that linode has a 50mbps cap (which I'm not even close to hitting, apparently). I had it raised to 100mbps. Since linode caps my traffic, and I'm not even hitting it, does this mean that my server should indeed be capable of outputting up to 100mbps but is limited by some other internal bottleneck? I just don't understand how networks at this large of a scale work; can they literally send data as fast as they can read from the HDD? Is the network pipe that big? In conclusion 1: Based on the above, I'm thinking I can definitely raise my 180RPS by adding an nginx load balancer on top of a multi nginx server setup at exactly 180RPS per server behind the LB. 2: If linode has a 50/100mbit limit that I'm not hitting at all, there must be something I can do to hit that limit with my single server setup. If I can read / transmit data fast enough locally, and linode even bothers to have a 50mbit/100mbit cap, there must be an internal bottleneck that's not allowing me to hit those caps that I'm not sure how to detect. Correct? I realize the question is huge and vague now, but I'm not sure how to condense it. Any input is appreciated on any conclusion I've made.

  Read the article

• opennms postgres connection slow

  - by krisdigitx

  i am running the opennms application server on a physical server and the database on an ESXi VM. Recently the opennms webconsole has been very slow to load as such i deleted most of the events from the database table, now both servers have no load at all, and the psql connection from the application server to the database server is also very fast, but somehow opennms webconsole is still slow. this is the strace from the opennms process id: 18629 futex(0x2aaac77d8a84, FUTEX_WAIT_PRIVATE, 453, NULL <unfinished ...> 3015 futex(0x2aaabc4a2ee4, FUTEX_WAIT_PRIVATE, 323, NULL <unfinished ...> 10863 futex(0x2aaabbebaa94, FUTEX_WAIT_PRIVATE, 395, NULL <unfinished ...> 25260 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 10859 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 10982 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 3011 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 25260 futex(0x2aaae098fc28, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 10982 futex(0x2aaac0eaf928, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 3011 futex(0x2aaab0cb1728, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 10859 futex(0x2aaac062c328, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 25260 <... futex resumed> ) = 0 10982 <... futex resumed> ) = 0 3011 <... futex resumed> ) = 0 10859 <... futex resumed> ) = 0 25260 futex(0x2aaabc38b6b4, FUTEX_WAIT_PRIVATE, 443, NULL <unfinished ...> 10982 futex(0x2aaabc5d7b94, FUTEX_WAIT_PRIVATE, 99, NULL <unfinished ...> 3011 futex(0x2aaac7c55334, FUTEX_WAIT_PRIVATE, 183, NULL <unfinished ...> 10859 futex(0x2aaabbb8c9d4, FUTEX_WAIT_PRIVATE, 347, NULL <unfinished ...> 10846 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 10846 futex(0x2aaae9022428, FUTEX_WAKE_PRIVATE, 1) = 0 10846 futex(0x2aaabe0030b4, FUTEX_WAIT_PRIVATE, 251, NULL <unfinished ...> 20281 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 14100 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 2925 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 10843 <... futex resumed> ) = -1 ETIMEDOUT (Connection timed out) 20281 futex(0x2aaac7e93628, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 14100 futex(0x2aaac04e8c28, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 2925 futex(0x2aaaec085528, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> 10843 futex(0x2aaab20b0528, FUTEX_WAKE_PRIVATE, 1 <unfinished ...> and shows lots of connection timeout??? i think its the connection between the java application and database which is causing issues. any ideas how to troubleshoot this???

  Read the article

• php-fpm + persistent sockets = 502 bad gateway

  - by leeoniya

  Put on your reading glasses - this will be a long-ish one. First, what I'm doing. I'm building a web-app interface for some particularly slow tcp devices. Opening a socket to them takes 200ms and an fwrite/fread cycle takes another 300ms. To reduce the need for both of these actions on each request, I'm opening a persistent tcp socket which reduces the response time by the aforementioned 200ms. I was hoping PHP-FPM would share the persistent connections between requests from different clients (and indeed it does!), but there are some issues which I havent been able to resolve after 2 days of interneting, reading logs and modifying settings. I have somewhat narrowed it down though. Setup: Ubuntu 13.04 x64 Server (fully updated) on Linode PHP 5.5.0-6~raring+1 (fpm-fcgi) nginx/1.5.2 Relevent config: nginx worker_processes 4; php-fpm/pool.d pm = dynamic pm.max_children = 2 pm.start_servers = 2 pm.min_spare_servers = 2 Let's go from coarse to fine detail of what happens. After a fresh start I have 4x nginx processes and 2x php5-fpm processes waiting to handle requests. Then I send requests every couple seconds to the script. The first take a while to open the socket connection and returns with the data in about 500ms, the second returns data in 300ms (yay it's re-using the socket), the third also succeeds in about 300ms, the fourth request = 502 Bad Gateway, same with the 5th. Sixth request once again returns data, except now it took 500ms again. The process repeats for several cycles after which every 4 requests result in 2x 502 Bad Gateways and 2x 500ms Data responses. If I double all the fpm pool values and have 4x php-fpm processes running, the cycles settles in with 4x successful 500ms responses followed by 4x Bad Gateway errors. If I don't use persistent sockets, this issue goes away but then every request is 500ms. What I suspect is happening is the persistent socket keeps each php-fpm process from idling and ties it up, so the next one gets chosen until none are left and as they error out, maybe they are restarted and become available on the next round-robin loop ut the socket dies with the process. I haven't yet checked the 'slowlog', but the nginx error log shows lots of this: *188 recv() failed (104: Connection reset by peer) while reading response header from upstream, client:... All the suggestions on the internet regarding fixing nginx/php-fpm/502 bad gateway relate to high load or fcgi_pass misconfiguration. This is not the case here. Increasing buffers/sizes, changing timeouts, switching from unix socket to tcp socket for fcgi_pass, upping connection limits on the system....none of this stuff applies here. I've had some other success with setting pm = ondemand rather than dynamic, but as soon as the initial fpm-process gets killed off after idling, the persistent socket is gone for all subsequent php-fpm spawns. For the php script, I'm using stream_socket_client() with a STREAM_CLIENT_PERSISTENT flag. A while/stream_select() loop to detect socket data and fread($sock, 4096) to grab the data. I don't call fclose() obviously. If anyone has some additional questions or advice on how to get a persistent socket without tying up the php-fpm processes beyond the request completion, or maybe some other things to try, I'd appreciate it. some useful links: Nginx + php-fpm - recv() error Nginx + php-fpm "504 Gateway Time-out" error with almost zero load (on a test-server) Nginx + PHP-FPM "error 104 Connection reset by peer" causes occasional duplicate posts http://www.linuxquestions.org/questions/programming-9/php-pfsockopen-552084/ http://stackoverflow.com/questions/14268018/concurrent-use-of-a-persistent-php-socket http://devzone.zend.com/303/extension-writing-part-i-introduction-to-php-and-zend/#Heading3 http://stackoverflow.com/questions/242316/how-to-keep-a-php-stream-socket-alive http://php.net/manual/en/install.fpm.configuration.php https://www.google.com/search?q=recv%28%29+failed+%28104:+Connection+reset+by+peer%29+while+reading+response+header+from+upstream+%22502%22&ei=mC1XUrm7F4WQyAHbv4H4AQ&start=10&sa=N&biw=1920&bih=953&dpr=1

  Read the article

• Permissions Required for Sharepoint Backups

  - by Wyatt Barnett

  We are in the process of rolling out an extranet for some of our partners using WSS 3.0 as the platform. We already use it internally for a variety of things, and we are using the following powershell script to backup the server: param( $url="http://localhost", $backupFolder="c:\" ) [System.Reflection.Assembly]::LoadWithPartialName("Microsoft.SharePoint") $site= new-Object Microsoft.SharePoint.SPSite($url) $names=$site.WebApplication.Sites.Names foreach ($name in $names) { $n2 = "" if ($name.Length -eq 0) { $n2="ROOT" } else { $n2 = $name } $tmp=$n2.Replace("/", "_") + ".sbk" $saveas = "" if ($backupFolder.Length -eq 0) { $saveas = $tmp } else { $saveas = join-path -path $backupFolder -childPath $tmp } $site.WebApplication.Sites.Backup($name, $saveas, "true") write-host "$n2 backed up to $saveas." } This script works perfectly on the current installation running as our domain backup user. On the new box, it fails when ran as the backup user--claiming "The web application located at http://extranet/" could not be found. That url does, in fact, work so I'm fairly certain it isn't anything that dumb and rather is some permissions issue. Especially because, when executed from my security context, the script works perfectly. I have tried making the backup user a farm owner, as well as added him to the various site collection admin groups on the extranet. The one major difference between the extranet and the intranet server is that the extranet has an alternative access mapping (for https://xnet.example.com) and also uses forms authentication for that mapping. Anyhow, what permissions (or other voodoo) do I need to setup to get this script to work properly?

  Read the article

• apache webserver unresponsible with server-status showing all child processes waiting for connection

  - by Jeff

  My setup: i have 3 nearly identical webserver machines serving the same high loaded dynamic website with simple load balancing over dns. The service has been working for over two ears with the same apache config. apache2, php5, ubuntu 8.04 linux 2.6.24-29-server My problem: since about two weeks i'm experiencing problems with this config. Nearly every day i have one small moment about 5 minutes, in which the website is unreachable. I'm still able to login to the servers over ssh. If i run htop, i see the machine simply doing nothing. i have about 1000 apache processes running, but no cpu activity. i've used the apache mod_status to debug this situation. the process scoreboard looks like this: _C.___K_______________________R._______.__K_K____K___C_______.__ _______C__________.___________________________________.________C _.____K__________K___K_WK_____._K_____________________________._ W______K__________K________.____________________._______C_______ _C_.__K__K____.._.._____________________________________C_______ _R___________K___.______C________.C_________.______._____C______ ____________KKC____K_____K__WC_________________C_____.__.____.__ _____________________C_________K______.____C______._____________ _.___C____.___.___________________________.K______.____K________ W__.___________________C.__.____K________K_______R_._.__._______ __C__C_.__________C__C_______._____W______________C_.___C_______ ____.______C_____________C________.____C____________.________._K __.__________.K_____________K_________._____C____.K__________KW_ __K.W________R_________._______.___W___________.____.__K_____W__ W___.___..________W____K Scoreboard Key: "_" Waiting for Connection, "S" Starting up, "R" Reading Request, "W" Sending Reply, "K" Keepalive (read), "D" DNS Lookup, "C" Closing connection, "L" Logging, "G" Gracefully finishing, "I" Idle cleanup of worker, "." Open slot with no current process So the most of the processes are just waiting for connection. after about 5 minutes the situation will return to normal: i have lot least processes on every machine, the most workers have the "."-status (meaing they are open to process a request) and of course the website is reachable! so i'm trying to find something in the logs, but there is simply nothing... the apache access log is silent for about 4 minutes, the same is for the error log. i also can not figure out anything wrong in other system logs. the situation is the same on all 3 webservers (all of them have this load peak and unresposibility at the same time), so i do not thing this is hardware related. but i think, this might be related to some network (tcp) issue. any ideas? EDIT: some more information, that i have just discovered: it has just happened again. and i was able to verify that i'm also not able to connect locally when this problem occurs. i have made some connection statistics with the following command after it happend netstat -an|awk '/tcp/ {print $6}'|sort|uniq -c 109 CLOSE_WAIT 2652 ESTABLISHED 2 FIN_WAIT1 11 LAST_ACK 12 LISTEN 91 SYN_RECV 1 SYN_SENT 16 TIME_WAIT If i execute the same command some time later, i have something like this: 4 CLOSING 108 ESTABLISHED 18 FIN_WAIT1 182 FIN_WAIT2 37 LAST_ACK 12 LISTEN 50 SYN_RECV 11276 TIME_WAIT So in the normal situation i have only 100-200 open connections by clients beeing handled by apache in this moment. when i have this "crash", i have a lot more connections. what is the best way to analyse this? EDIT2: the important lines in apache2.conf are: KeepAlive On MaxKeepAliveRequests 20 KeepAliveTimeout 1 <IfModule mpm_prefork_module> ServerLimit 920 StartServers 30 MinSpareServers 80 MaxSpareServers 120 MaxClients 920 MaxRequestsPerChild 700 </IfModule> it is an apache2 prefork with php_mod. the server has 8GB ram and a 4gb swap partition.

  Read the article

• Being a more attractive job candidate - Certs XOR Degree

  - by Zephyr Pellerin

  I'm currently working in an IT position, where I do helpdesk stuff, and predominantly security related issues/consulting (In the loosest sense of the term) In-House and for Service-Contract clients (as the only/acting CCSP [I guess I should say only person with Cisco experience] in my organization). I've professionally written Kernel Mode drivers for a gaming company. Among other things that I'm proud to put on a resume. I think of myself as very reasonably qualified as a System Administrator, With excellent Cisco experience, among other things I think would make a good addition to almost any IT staff in need of a new employee. However, Something has always tripped me up - Human Resources. Let me explain, I decided to skip the university route - I'm immensely glad that I did, The computer science graduates that I've met and work with rarely know much of anything about Computers (Until they gain some 'real' experience), Even when asked about Theoretical Computing fundamentals they can rattle something off about Turing Completeness but rarely do they understand the mathematical underpinnings. In short, I think instead of going to college, I'd rather pick up some real world experience. However, Apparently, Employers rarely think the same way. A quick perusal of jobs through the standard job search engine yields nothing short of a conspiracy to exclude anyone without 'A Bachelors Degree in Computer Science or Equivalent'. Interviews I've had in the past have almost always been entangled with - 1. My Age (Which I can't really change) and 2. Lack of Degree. Employers frequently disregard the CCNA/CCSP, The experience I've gained through internships, My extensive experience in x86 assembly and C, among so many other things I like to think are valuable to employers - In lieu of the fact that I don't have a piece of paper. So, AS AN EMPLOYER - Is it even worth working on my CCIE? Or should I pad my resume with certifications that are easier to acquire (Like CISSP, MSCE, Network+, etc.). Or should I ditch the whole idea and head back to get a Mathematics or CS degree?

  Read the article

• RAID administration in Debian Lenny

  - by Siim K

  I've got an old box that I don't want to scrap yet because it's got a nice working 5-disk RAID assembly. I want to create 2 arrays: RAID 1 with 2 disks and RAID 5 with the other 3 disks. The RAID card is Intel SRCU31L. I can create the RAID 1 volume in the console that you access with Ctrl+C at startup. But it only allows for creation of one volume so I can't do anything with the 3 remaining disks. I installed Debian Lenny on the RAID 1 volume and it worked out nicely. What utilites could I now use to create/manage the RAID volumes in Debian Linux? I installed the raidutils package but get an error when trying to fetch a list: #raidutil -L controller or #raidutil -L physical # raidutil -L controller osdOpenEngine : 11/08/110-18:16:08 Fatal error, no active controller device files found. Engine connect failed: Open What could I try to get this thing working? Can you suggest any other tools? Command #lspci -vv gives me this about the controller: 00:06.1 I2O: Intel Corporation Integrated RAID (rev 02) (prog-if 01) Subsystem: Intel Corporation Device 0001 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step ping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: Memory at f9800000 (32-bit, prefetchable) [size=8M] [virtual] Expansion ROM at 30020000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: PCI_I2O Kernel modules: i2o_core

  Read the article

• Configuration for httphandler in classic mode

  - by happyspider

  I have to install an httphandler that needs to run on classic mode. I have created an application on the iis that uses a classic apppool and put the handler assembly there. The vendor gave me a configuration in the deployment document that looks like this: <system.web> <globalization requestEncoding="iso-8859-1" responseEncoding="iso-8859-1" /> <httpModules> </httpModules> <httpHandlers> <add verb="*" path="*" type="ProductName.ProductName, ProductName" /> </httpHandlers> </system.web> <system.webServer> <validation validateIntegratedModeConfiguration="false"/> <handlers> <add name="someUnspecificName" path="*" verb="*" modules="IsapiModule" scriptProcessor="C:\Windows\Microsoft.NET\Framework\v2.0.50727\aspnet_isapi.dll" resourceType="Unspecified" requireAccess="None" preCondition="classicMode,runtimeVersionv2.0,bitness32" /> </handlers> </system.webServer> The error I get when requesting a URL on the application is a 404, so I guess the handle is not used at all. Does the configuration look ok for a 64bit system?

  Read the article

• Debian virtual memory reaching limit

  - by Gregor

  As a relative newbie to systems, I inherited a Debian server and I've noticed that virtual memory is very high (around 95%!). The server has been running slow for around 6 months, and I was wondering if any of you had any tips on things I could try, particularly on freeing up memory. The server hosts various websites and also a Postit email server. Here are the details: Operating system Debian Linux 5.0 Webmin version 1.580 Time on system Thu Apr 12 11:12:21 2012 Kernel and CPU Linux 2.6.18-6-amd64 on x86_64 Processor information Intel(R) Core(TM)2 Duo CPU E7400 @ 2.80GHz, 2 cores System uptime 229 days, 12 hours, 50 minutes Running processes 138 CPU load averages 0.10 (1 min) 0.28 (5 mins) 0.36 (15 mins) CPU usage 14% user, 1% kernel, 0% IO, 85% idle Real memory 2.94 GB total, 1.69 GB used Virtual memory 3.93 GB total, 3.84 GB used Local disk space 142.84 GB total, 116.13 GB used Free m output: free -m total used free shared buffers cached Mem: 3010 2517 492 0 107 996 -/+ buffers/cache: 1413 1596 Swap: 4024 3930 93 Top output: top - 11:59:57 up 229 days, 13:38, 1 user, load average: 0.26, 0.24, 0.26 Tasks: 136 total, 2 running, 134 sleeping, 0 stopped, 0 zombie Cpu(s): 3.8%us, 0.5%sy, 0.0%ni, 95.0%id, 0.7%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3082544k total, 2773160k used, 309384k free, 111496k buffers Swap: 4120632k total, 4024712k used, 95920k free, 1036136k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 28796 www-data 16 0 304m 68m 6188 S 8 2.3 0:03.13 apache2 1 root 15 0 10304 592 564 S 0 0.0 0:00.76 init 2 root RT 0 0 0 0 S 0 0.0 0:04.06 migration/0 3 root 34 19 0 0 0 S 0 0.0 0:05.67 ksoftirqd/0 4 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 5 root RT 0 0 0 0 S 0 0.0 0:00.06 migration/1 6 root 34 19 0 0 0 S 0 0.0 0:01.26 ksoftirqd/1 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/1 8 root 10 -5 0 0 0 S 0 0.0 0:00.12 events/0 9 root 10 -5 0 0 0 S 0 0.0 0:00.00 events/1 10 root 10 -5 0 0 0 S 0 0.0 0:00.00 khelper 11 root 10 -5 0 0 0 S 0 0.0 0:00.02 kthread 16 root 10 -5 0 0 0 S 0 0.0 0:15.51 kblockd/0 17 root 10 -5 0 0 0 S 0 0.0 0:01.32 kblockd/1 18 root 15 -5 0 0 0 S 0 0.0 0:00.00 kacpid 127 root 10 -5 0 0 0 S 0 0.0 0:00.00 khubd 129 root 10 -5 0 0 0 S 0 0.0 0:00.00 kseriod 180 root 10 -5 0 0 0 S 0 0.0 70:09.05 kswapd0 181 root 17 -5 0 0 0 S 0 0.0 0:00.00 aio/0 182 root 17 -5 0 0 0 S 0 0.0 0:00.00 aio/1 780 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata/0 782 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata/1 783 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata_aux 802 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_0 803 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_1 804 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_2 805 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_3 1013 root 10 -5 0 0 0 S 0 0.0 49:27.78 kjournald 1181 root 15 -4 16912 452 448 S 0 0.0 0:00.05 udevd 1544 root 14 -5 0 0 0 S 0 0.0 0:00.00 kpsmoused 1706 root 13 -5 0 0 0 S 0 0.0 0:00.00 kmirrord 1995 root 18 0 193m 3324 1688 S 0 0.1 8:52.77 rsyslogd 2031 root 15 0 48856 732 608 S 0 0.0 0:01.86 sshd 2071 root 25 0 17316 1072 1068 S 0 0.0 0:00.00 mysqld_safe 2108 mysql 15 0 320m 72m 4368 S 0 2.4 1923:25 mysqld 2109 root 18 0 3776 500 496 S 0 0.0 0:00.00 logger 2180 postgres 15 0 99504 3016 2880 S 0 0.1 1:24.15 postgres 2184 postgres 15 0 99504 3596 3420 S 0 0.1 0:02.08 postgres 2185 postgres 15 0 99504 696 628 S 0 0.0 0:00.65 postgres 2186 postgres 15 0 99640 892 648 S 0 0.0 0:01.18 postgres

  Read the article

• what is best config for nginx worker_rlimit_nofile and worker_connections 28672

  - by Binh Nguyen

  i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

  Read the article

• What would cause Memcached to Hang for 2+ seconds?

  - by Brad Dwyer

  I'm going nuts trying to scale memcached. From their site: Memcached operations are almost all O(1). Connecting to it and issuing a get or stat command should never lag. If connecting lags, you may be hitting the max connections limit. See ServerMaint for details on stats to monitor. If issuing commands lags, you can have a number of tuning problems. Most common are hardware problems, not enough RAM (swapping), network problems (bandwidth, dropped packets, half-duplex connections). On rare occasion OS bugs or memcached bugs can contribute. Well.. it is most certainly not performing like an O(1) operation for me. Under low to normal load on our site memcached response times for get and set ops are about 0.001 seconds. Not bad. But if we triple the load we get outliers that take 100x (or in rare cases 1000x!) that long. I even had one instance where it took 2.2442 seconds for memcached to store a value. Obviously this is killing our site. Here's the output of Memcached-getStats during one of the slow periods: [pid] => 18079 [uptime] => 8903 [threads] => 4 [time] => 1332795759 [pointer_size] => 32 [rusage_user_seconds] => 26 [rusage_user_microseconds] => 503872 [rusage_system_seconds] => 125 [rusage_system_microseconds] => 477008 [curr_items] => 42099 [total_items] => 422500 [limit_maxbytes] => 943718400 [curr_connections] => 84 [total_connections] => 4946 [connection_structures] => 178 [bytes] => 7259957 [cmd_get] => 1679091 [cmd_set] => 351809 [get_hits] => 1662048 [get_misses] => 17043 [evictions] => 0 [bytes_read] => 109388476 [bytes_written] => 3187646458 [version] => 1.4.13 So things that I have ruled out so far are: Hitting the max connections limit (curr_connections of 84 is well below the default of max of 1024) Swapping - the machine has 900M out of 1024M of memory dedicated to memcached on a dedicated machine. It only appears to be using about 7MB of data as per the bytes stat. How would I diagnose the other hardware problems? prstat doesn't really show a whole lot going on in terms of CPU or memory usage. Not sure how to figure out the network problems but as this is a dedicated server on the same private network as the web box I don't think it's a connectivity issue (ping is less than a millisecond between the boxes). Is there something else I'm missing here? It's driving me nuts. Edit: Also forgot to mention that I've tried both persistent and non-persistent connections with minimal-to-no impact.

  Read the article

• Dell XPS 1530 DVD-RW firmware problem

  - by josecortesp

  Hello everyone. I have this XPS laptop since a year and a half ago. About 2 months ago, with the waranty expired, i tried to run the optiarc slot load DVD-RW firmware update, and said everything was okay. Then I restarted it and the problem started: Now, every single time I turn on my computer, it get stuck at the BIOS POST until the drive sounds like "ready" and then the computer starts normally. And this happen EXACTLY the same when it's getting back from sleep. I'm pretty sure is not a software issue, because I tried with Vista Home Premiun 32 bits, Ubuntu (from 8.10+)32 & 64, and with W7 64. Already tried to run the firmware installer like a million time, in case it is a failing install with no luck. Also, google it to see if someone has the same problem, and again, no. The Drive performs pretty okay once the System is on, but waiting to the drive to be ready everytime is really annoying. The Firmware I updated was this, and the drive is: K937C Assembly, Dvd+/-rw, 8, SLOT, 1530 Sony Nec Optiarc Inc. I'll apreciate any help you can give me

  Read the article

• Why does my computer run slowly and freeze sometimes?

  - by Brae

  EDIT I disabled sound in the BIOS, rebooted and it hung. I removed the (previously) faulty HDD, rebooted and it hung. I have managed to get my Realtek audio manager open again after its mysterious disappearance. Subsequently my microphone is now working again, to fix it I had to uninstall audio drivers, disable audio in BIOS, install audio drivers, enable audio in BIOS. Access via network (with faulty HDD in) seems to not be triggering hangs at the moment. I think with the sound problem fixed it might play a little nicer, but I think its still going to hang. If it does, then I'm fairly sure its been narrowed down to the mobo. EDIT Pretty convinced my motherboard is the culprit, because nothing else seems to have any obvious problems (bar the hard drive, which the PC still hangs without it being plugged in) So thank you all for helping, once I get more rep ill up a few of the answers. My PC is doing some weird things... Sometimes when I open up a program, lets say Adobe Photoshop, it will load everything normally, nice and quick no problems and I can use it fine. Other times its a little odd, and it loads the program as if it's only using half of the CPU. It's pretty obvious when it does it, normally the loading screen skims past, but when it does this weird load you see it slowly tick though each thing, and the program itself becomes incredibly slow. Even Google Chrome does it sometimes. Yet when I exit and reopen the program without doing anything else, it typically opens fine without lagging. I think this problem is probably a symptom of something bigger, because of other problems I'm having. Random hangs; no matter what I have open or what I'm doing. My PC will sort of freeze up for a few seconds. If music is playing it will either loop the last second or two, or it will buzz. This only lasts for a few seconds then it returns to normal without having to restart. During this time all programs lock up and freeze, and the mouse and keyboard are useless. I am also having a weird issue with my audio jacks, without touching my PC at all, sometimes I will see a popup saying that I have unplugged something or plugged something in, neither of which has actually happened. Pretty sure this is cause by the motherboard. I recently had a 'Pink Screen of Death' (yes pink) which pointed to my audio drivers. The lockups seem to happen with some consistency when someone is accessing my shared files via my home LAN. Which leads me to believe either one of my hard drives is acting up or more likely the controller. One of my drives had a bit of a crash before, I used Spinrite and managed to recover my stuff and now the drive appears to be working okay. This is possibly adding to the problems. My best guess is something has gone wrong with my motherboard, possibly a power issue or a chip has died, I really don't know. So what I would like to know is: Have I have missed some obvious diagnostic to help figure out what it is, or should I just bite the bullet and assume its my motherboard acting up and buy a new system? dxdiag[64-bit] - http://pastebin.com/G30kb2TL PSOD (minidump) - http://pastebin.com/aZsv0H56 HWiNFO64 (system info / specs) - http://pastebin.com/X6h3K8g6

  Read the article

• Where is my VMware-ws FreeNAS CIFS(ZFS) bottle-neck?

  - by maka

  Background: I'm building a quiet HTPC + NAS that is also supposed to be used for general computer usage. I'm so far generally happy with things, it was just that I was expecting a little better IO performance. I have no clue if my expectations are unreal. The NAS is there as a general purpose file storage and as a media server for XBMC and other devices. ZFS is a requirement. Question: Where is my bottle-neck, and is there anything I can do config wise, to improve my performance? I'm thinking VM-disk settings could be something but I really have no idea where to go since I'm neither experienced with FreeNAS nor VMware-WS. Tests: When I'm on the host OS and copy files (from the SSD) to the CIFS share, I get around 30 Mbytes/sec read and write. When I'm on my laptop laptop, wired to the network, I get about the same specs. The test I've done are with a 16 GB ISO, and with about 200 MB of RARs and I've tried avoiding the RAM-cache by reading different files than the ones I'm writing ( 10 GB). It feels like having less CPU cores is a lot more efficient, since the resource manager in Windows reports less CPU-usage. With 4 cores in VMware, CPU usage was 50-80%, with 1 core it was 25-60%. EDIT: HD ActiveTime was quite high on SSD so I moved the page file, disabled hibernate and enabled Win DiskCache both on SSD and RAID. This resulted in no real performance difference for one file, but if i transferred 2 files the total speed went up to 50 Mbytes/s vs ~40. The ActiveTime avg also went down a lot (to ~20%) but has now higher bursts. DiskIO is on ~ 30-35 Mbytes/s avgs, with ~100Mb bursts. Network is on 200-250Mbits/s with ~45 active TCP connections. Hardware Asus F2A85-M Pro A10-5700 16GB DDR3 1600 OCZ Vertex 2 128GB SSD 2x Generic 1tb 7200 RPM drives as RAID0 (in win7) Intel Gigabit Desktop CT Software Host OS: Win7 (SSD) VMware Worksation 9 (SSD) FreeNAS 8.3 VM (20GB VDisk on SSD) CPU: I've tried 1, 2 and 4 cores. Virtualisation engine, Preferred mode: Automatic 10,24Gb ram 50Gb SCSI VDisk on the RAID0, VDisk is formatted as ZFS and exposed through CIFS through FreeNAS. NIC Bridge, Replicate physical network state Below are two typical process print-outs while I'm transfering one file to the CIFS share. last pid: 2707; load averages: 0.60, 0.43, 0.24 up 0+00:07:05 00:34:26 32 processes: 2 running, 30 sleeping Mem: 101M Active, 53M Inact, 1620M Wired, 2188K Cache, 149M Buf, 8117M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 102 0 50164K 10364K RUN 0:25 25.98% smbd 1897 root 6 44 0 168M 74808K uwait 0:02 0.00% python last pid: 2746; load averages: 0.93, 0.60, 0.33 up 0+00:08:53 00:36:14 33 processes: 2 running, 31 sleeping Mem: 101M Active, 53M Inact, 4722M Wired, 2188K Cache, 152M Buf, 5015M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 76 0 50164K 10364K RUN 0:52 16.99% smbd 1897 root 6 44 0 168M 74816K uwait 0:02 0.00% python I'm sorry if my question isn't phrased right, I'm really bad at these kind of things, and it is the first time I post here at SU. I also appreciate any other suggestions to something, I could have missed.

  Read the article

• 1600+ 'postfix-queue' processes - OK to have this many?

  - by atomicguava

  I have a Plesk 9.5.4 CentOS server running Postfix. I had been having massive problems with the mailq being full of 'double-bounce' email messages containing errors relating to 'Queue File Write Error', but I believe these are now fixed thanks to this thread. My new problem is that when I run top, I can see lots of processes called 'postfix-queue' and have fairly high load: top - 13:59:44 up 6 days, 21:14, 1 user, load average: 2.33, 2.19, 1.96 Tasks: 1743 total, 1 running, 1742 sleeping, 0 stopped, 0 zombie Cpu(s): 5.1%us, 8.8%sy, 0.0%ni, 85.3%id, 0.8%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3145728k total, 1950640k used, 1195088k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1324 apache 16 0 344m 33m 5664 S 21.7 1.1 0:03.17 httpd 32443 apache 15 0 350m 36m 6864 S 14.4 1.2 0:13.83 httpd 1678 root 15 0 13948 2568 952 R 2.0 0.1 0:00.37 top 1890 mysql 15 0 689m 318m 7600 S 1.0 10.4 219:45.23 mysqld 1394 apache 15 0 352m 41m 5972 S 0.7 1.3 0:03.91 httpd 1369 apache 15 0 344m 33m 5444 S 0.3 1.1 0:02.03 httpd 1592 apache 15 0 349m 37m 5912 S 0.3 1.2 0:02.52 httpd 1633 apache 15 0 336m 20m 1828 S 0.3 0.7 0:00.01 httpd 1952 root 19 0 335m 28m 10m S 0.3 0.9 1:35.41 httpd 1 root 15 0 10304 732 612 S 0.0 0.0 0:04.41 init 1034 mhandler 15 0 11520 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1036 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1041 mhandler 17 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1043 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1063 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1068 mhandler 15 0 11516 1128 860 S 0.0 0.0 0:00.00 postfix-queue 1071 mhandler 17 0 11512 1152 884 S 0.0 0.0 0:00.00 postfix-queue 1072 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1081 mhandler 16 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1082 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1089 popuser 15 0 33892 1972 1200 S 0.0 0.1 0:00.02 pop3d 1116 mhandler 16 0 11516 1164 884 S 0.0 0.0 0:00.00 postfix-queue 1117 mhandler 15 0 11516 1124 860 S 0.0 0.0 0:00.00 postfix-queue 1120 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1121 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1130 mhandler 17 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1131 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1149 root 17 -4 12572 680 356 S 0.0 0.0 0:00.00 udevd 1181 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1183 mhandler 15 0 11512 1116 860 S 0.0 0.0 0:00.00 postfix-queue 1224 mhandler 16 0 11516 1160 884 S 0.0 0.0 0:00.00 postfix-queue 1225 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1228 apache 15 0 345m 34m 5472 S 0.0 1.1 0:04.64 httpd 1241 mhandler 16 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1242 mhandler 15 0 11512 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1251 mhandler 17 0 11516 1156 884 S 0.0 0.0 0:00.00 postfix-queue 1252 mhandler 15 0 11516 1120 860 S 0.0 0.0 0:00.00 postfix-queue 1258 apache 15 0 349m 37m 5444 S 0.0 1.2 0:01.28 httpd When I run ps -Al | grep -c postfix-queue it returns 1618! My question is this: is this normal or is there something else going wrong with Postfix? Right now, if I run mailq it is empty, and qshape deferred / qshape active are empty too. Thanks in advance for your help.

  Read the article

< Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >